Cruise Control Fitting

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Cruise Control Installation Guide Vauxhall Corsa C Vehicle Engine Codes: Z12XEP Z14XEP Approximate Years: 54 > 56 plates

[22/03/2014] Steps Performed on the following model: Vauxhall Corsa Z14XEP 1.4 Twinport 2006 Facelift 5 Door SXI+

EARLY APOLOGIES FOR ANY GRAMMATICAL ERRORS READ THE DISCLAIMER SECTION ON PRINCIPLE TO UNDERSTAND THE SERIOUS IMPLICATIONS THAT COULD RESULT FOLLOWING FAILURE TO CORRECTLY MODIFY THE CAR

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Recognition Thanks for all the help figuring out how to make the MOD work credit goes to these people on Corsa C UK for their help. It would not have been easy or essentially possible to produce this guidance however, neither the author nor related contributors accept any responsibility for the information contained within this guide – and therefore reject all prior legal responsibility to any damage/ accident or loss following the guidance of this guide.

If you want a list of the contributors I can provide it to you at a later date but they all know who they are!

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

DISCLAIMER – YOU MUST READ THIS FIRST! I (THE AUTHOR) DO NOT IN ANY WAY SHAPE OR FORM ACCEPT LIABILITY FOR ANY DAMAGE/ INJURY OR LOSS RESULTING FROM THIS GUIDE ON CRUISE CONTROL INSTALLATION AND DO NOT CODONE ITS USE AS STRICT RULE, IT IS MEANT AS A GUIDE ON HOW CRUISE CONTROL COULD BE ADDED – AND HENCE FORTH REJECT ANY RESPONSIBILITY FOR YOUR ACTIONS RESULTING FROM THIS GUIDANCE. DURING THIS MODIFICATION – THERE IS THE POSSIBILITY YOU COULD IRREVERIABILY DAMAGE YOUR CARS ELECTRICAL AND MECHNICAL SYSTEMS AND THEREFORE THE UPMOST CARE SHOULD BE TAKEN DURING EACH STEP. YOU MUST HAVE A REASONABLE AMOUNT OF EXPERIENCE OF ELECTRONICS AND AUTOMATIVE TECHNICS IN ORDER TO CORRECTLY STEER THROUGH THE STEPS. It is the car owner/ drivers responsibility to ensure the safety of their vehicle following any modification to the electrical system. If you are concerned about any aspect of this guide DO NOT attempt it – and have a fully qualified automotive technician check the safety of your vehicle by way of a safety check or MOT. This guidance is not necessarily the best or proper way to handle the cars electrical system and my methods/ techniques are therefore to be considered as ‘bad practice’ in all shapes and form – for your own protection.

THIS MODIFICATION HAS THE POTENTIAL TO DO SERIOUS BODILY HARM SHOULD THE SYSTEM MALFUNCTION AND HENCE FAILS TO DISABLE. THEREFORE IT IS THE DRIVERS/ OWNERS RESPONSBILITY TO TAKE THIS INTO CONSIDERATION BEFORE USE OR INSTALLATION OF THE CRUISE CONTROL RETROFIT SYSTEM Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

INTRODUCTION: No doubt you find yourself reading this guide today because you find yourself with foot ache or because you are a long distance driver wanted cruise control that was not natively fitted to your Corsa C. The cruise control system was an optional extra on Vauxhall Corsa’s and came as part of the “Plus Pack” which included 16” alloy wheels, remote ultrasonic alarm system. It was ONLY available on MANUAL models.

Corsa C Facelift Variants < In order of features from poverty to sport >  Expression (cheapest, poverty model)  Life  Design  SXI  SXI+  SRI (most expensive, sports model)

I will seek to show you the steps that are required in installing Cruise Control (CC) into your FACELIFT Corsa C; with images and diagrammatic representations of the wiring system surrounding your Motronic Canbus Engine Control Unit.

Don’t bother rushing your Cruise Control Installation – take this guide and re-read every step and plan. It takes perseverance to get the system to work! Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

A breakdown then of the steps you will be required to carry out to get the system live:

1. ) Check your engine code is compatible with that of this manual Z12XEP (1.2 Twinport) Z14XEP (1.4 Twinport) Should you have a different engine code I will provide some information at the back of this book about slight differences in the steps you need to take to get the system working and the troubles you may have.

2. ) Stalk/ Indicator Wiring at dashboard level Pin 4 of Indicator/ Cruise Stalk > Pin 2 of Body Control Module Plug Facelift Corsa’s SHOULD have this cable in situ as standard on (SXI/ SXI+) models but I have not investigated any other models/ variants.

3. ) Cruise Control Switch Assembly and Wiring Clutch Switch Pin (there are only two) to Pin 8 of Engine Control Unit Delphi Plug

4. ) Engine Control Unit Wiring Entering the Delphi Plug/ inserting a wire and clip safely

5. ) OPCOM programming steps Using your OPCOM programme to activate Cruise Control in the Engine Management and Body Control System

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Catch 22: Find these things out first!  Pin 4 Stalk to Pin 2 BCM – brown and grey wire? Remove your trim panels in the drivers foot well and the Steering Cowling to determine if you have this wire. If you do like I did then your job is 50% done.

 Pin 8 Delphi Connector ECU (X53) – Pin 4 Clutch Switch It is unlikely that you have this wire in situ. Using the Dephi Plug disassembly guide – check to see if you have a GREY wire coming from Pin 8 – I did! Although I never used it. If you don’t it is not the end of the world. If you do: Check the next set of places: Plug X21 (drivers footwell) Pin 10 – as seen in the red circle.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

X1 – Pin 34 It is my opinion that if the grey cable does not meet you in the interior loom at plug X21 Pin 10, it will be at the X1 socket at pin 34 (red ring). Should this be the case I would disregard its presence and fit a new cable as the hassle of getting at it in the body control module is more work that its worth. HOWEVER, if you are trying to wire a stalk wire Pin 4 to BCM Pin 2 on the X45 BCM plug (green ring) you may have more of a chance and it MAY be worthwhile.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Step 1: What you will need (Shopping List) Tools:      

Torx Screwdriver/ ¼ Drive Socket Set/ Allen Keys

     

Insulation Tape

Wire Strippers Wire Side cutters Soldering Iron/ Solder/ Flux Heatshrink Wire – approximately Gauge 16 – automotive high temp wire preferable Zip Ties/ Cable Tidy Precision Screwdrivers Standard size – Flat Head/ Philips Screwdrivers Long Nose Pliers Gloves (minimize injury, and dirt)

Hardware:     

Cruise Control Stalk – (£44.60 from Vauxhall) Clutch Switch – (£9.80 from Vauxhall) OPCOM – (£18 - £30 from Ebay) A portable computer from OPCOM Small radio control modelling connector or computer fan connector (commonly used in PC LED applications/ or Remote Control Cars/ PC fans) for connecting to Clutch Switch

 Delphi Wiring Harness Pin (from a Scrap Car: preferable car is a 05,55,06,56) plate Astra H as it has a long wire and pin to assist (you can pick out one from a Corsa C facelift but it will more difficuilt to find and harder to wire).

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

STEP 2: Indicator/ Cruise Control Stalk You MUST identify whether or not you have the correct number of wires installed in your indicator stalk. 1) Remove the steering column cover and expose the indicator stalk and its plug. 2) There should be 1 T20 Torx screw underneath the steering cover, and then two clips behind the steering wheel. 3) Once the covers are off – remove the indicator stalk by squeezing the lugs together to release the entire component. You then must remove the plug from the back by pushing the blue slider back and releasing a clip. 4) Now you need to check the presence of your wires: a. There should be FOUR (4) wires present at the plug and the cruise control wire is the BROWN/GREEN wire.

b. If your wire is NOT present you need to: Install a small 0.2mm wire from Pin 4 of this connector to Pin 2 of the Body Control Module Plug which is located in the engine bay on the nearside just in front of the car battery (under a cover which is waterproofed and sealed with Torx screws) 5) I HAVE NOT PROVIDED PHYSICAL IMAGES OF THE WIRING PROCESS AS MY MODEL VARIANT HAD THIS WIRE IN SITU HOWEVER ILL PROVIDE SOME DIAGMATIC VIEWS OF WHAT NEEDS TO BE DONE.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Possible steps to take if you need to install this cable: 1) Scavenge a donor stalk cable from a Corsa C with the plug to obtain the pin required to fit into the plug and a donor cable and pin from the BCM unit of the same car. 2) Run a small wire from this stalk down the steering system (without affecting the motion of the wheel) behind the dashboard to the BCM - this is located behind the glove compartment. 3) Disassemble the BCM by removing the control units – unpinning the BCM board and repining the plug with the scavenged wire. 4) Solder the two wires together and heat shrink.

Stalk Pin 4 goes to X45 plug Pin Number 2 – a visual representation of the plug is seen above. There is an approximate location in the CATCH 22 section of this document.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

STEP 3: Cruise Control Switch Wiring The cruise control switch is similar to that of a brake stop switch located just to the right of the clutch pedal. There has been people that have recycled a brake stop switch from Corsa C into the clutch switch and essentially that will work – however in the interest of a neat job I have purchased a proper PTB Clutch Position Switch and Connector. The clutch PTB switch works one of two ways depending on how it is wired and there is no information as to whether it remains live throughout ignition operation. When the pedal is at its highest position the switch will be pushed in on the CLOSED loop there is 12 volts to Pin 8 of the ECU. When you depress the clutch the circuit is broken and there should be no power to Pin 8. The ECU then knows that the pedal has been depressed and it should no longer continue CC throttle body regulation. You can check the voltage and wiring using a multimeter – to determine if any current is being transmitted through the cables – or without having the system live, resistance test the wiring (continuity test) to determine if the wire is good. It is located under the dashboard behind a series of covers and for the purpose of this I will not go into how to remove those – but a handy Haynes Manual or a Corsa C UK tutorial will show you how this is done.

The clutch switch is located inside that square metal piece of the clutch pedal assembly and sits “upside down” with the wires pointing up so the button makes contact with the pedal.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

If you happen to have a 1.7 Diesel Turbo Injected Engine from the Corsa C before 54 plate in the preface lift style you SHOULD have the wiring in place for the switch. If not you will need these two components: The physical switch and then a connector in order for reliable operation.

This is the switch and connector that I will be using in this tutorial. 1) With your clutch connector – the GREY wire is the wire that proceeds to pin 8 of the ECU and therefore is the signal. You will need to SOLDER (the only reliable way of wiring) onto the end of your lead – leaving a long stretch of wire to pass through the wall of the cockpit and down to the ECU. a. The new grey wire that you have extended will then pass behind the dashboard through the stereo and into the back of the glove compartment. 2) The BLACK connector is the ignition live, originally it was fed from Fuse 40 (a 10Amp rated fuse) however this is not possible to do effectively so you have two choices: a. Patch an ignition live from the brake stop switch on the middle peddle to the black wire (this is the recommended route). b. Place a wire from the cigarette lighter socket (wire behind), to an inline fuse holder with a rated fuse of 10 Amps, and then use this as your ignition live feed.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

You can see demonstrated the brake switch: To remove this – there are two lugs – one located underneath and the other on top – it can be very difficult to remove this switch but don’t just pull – take your time and remember to try and release those lugs without snapping them off. 1) There is two black and yellow wires and these are NOT to be touched. 2) Then there is a small black wire that looks across pins 1 and 3 – which is to carry a 12v ignition current over two pins. Then there is a single black wire proceeding up to the main loom. 3) You will need to cut this wire, strip it off and then attach another small wire and solder everything up together. 4) Before you solder, place a decent length of heat shrink on the unconnected wire so it can cover the soldered connection. But make sure it is cool first otherwise the heat shrink will not fit over and shrink itself before you have it correctly placed. 5) It is ridiculously difficult and soldering in a confined space its hard but eventually you will get it to connect as I did. 6) I did all this, and then placed some duct tape over the whole lot – just to protect the join from heat sources. You don’t have to but I was paranoid).

*WARNING: YOU AND VAUXHALL MUST CHECK & TRIPLE CHECK THE OPERATION OF YOUR BRAKE LIGHTS FOLLOWING THIS STEP! YOU ABSOLUTELY MUST NOT DRIVE ON ANY ROAD WITHOUT THEM WORKING* Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

You can see from the diagram to the left the location of the clutch switch and the wiring I have coming off of it. You can see vaguely the blue zip tie I have running around the switch holding the wires in place so that the connector does not come off. Here is a picture of the types of connector that can be used for the clutch switch – you can find this type of connector from a typical computer fan, or even something like a remote control car, or a computer reset/ light wire– this isn’t the precise one but I am confident that it will fit the switch pins! (The red and white wire/ connector I used was from an old PC reset switch) – Perfect fit!

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Fitting the Clutch Switch to the Pedal: I struggled to fit the clutch switch as it is a VERY tight fit: My advice is as follows: Find a spare but of cable and tie the clutch pedal down to the steering column so that you have more room to manoeuvre the switch. Do not bother pressing the lugs on the switch as you’ll only damage the plastic on them and then the switch won’t stay in.

4)

1) There is a red sheath located on the clutch switch – you will need to push this down slightly in order to remove the green security pin (protects the switch on transport) 2) Pull the red sheath back up to the top as this in affect allows the lugs that hold the switch in position to move in slightly as you push the switch in 3) Once the switch is push in – push the red sheath all the way back so it locks the switch in position Untie your clutch pedal and gently lift it in the first instance to come into contact with the switch as it locks the switch on the first contact.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

STEP 4: Engine Control Unit Wiring There are a number of things to consider with this step: 1) Are you competent and comfortable with messing with the cars can bus electrical wiring as without proper knowledge you could seriously damage the internal workings of the system and cause faults? 2) Are you prepared for it to go wrong? To be safe – consider what you will do if you damage the plug or wires – the bill for a new loom is approximately £250 from a registered Vauxhall Dealership so be prepared in case it all goes wrong! So at this stage you should have your cruise control stalk installed, and a clutch switch located with a single wire passing into the engine bay to be installed. Firstly you are wanted to install your cruise control wire onto the cars electrical loom on a DELPHI grey handle push fit plug (usually the lower of the two connectors). This has only one single wire passing out one side as opposed to the other bosch wire that has two and connects up all the engine sensors such as the Mass Air Flow, O2 Lambda, Crankshaft and Oil Pressure. This is a picture of the DELPHI plug from an actual Corsa C.

You can recognize this plug by its white central connector – its grey handle and slider than pass out of the plug on removal – this grey mechanism can be a bit stuff and using a screwdriver on the slider can help to unlock it from the control unit.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

This is a demonstration of the wires already fitted in this plug. They are not glued in on this model, and all that is required is a 0.35mm grey wire (or equivalent) to be installed along the top line (demonstrated in the image) on the 8th pin in from the grey slider side. You can see the line and reference point from the brown/ red wire located in pin 13 (see arrow). To get the correct wire and pin: Take a trip to your nearest scrap yard or phone them before hand to identify two things: 1) Do they have a Corsa C in stock beyond 54 plate (petrol 1.0/1.2/1.4). 2) Is there a loom still in situ for the ECU plug? Once you have located a suitable donor – remove the Delphi plug cutting as far from the plug as you can to give yourself lots of wire to play with. DO NOT ATTEMPT TO WIRE CRUISE CONTROL TO THE TOP PLUG PICTURED BELOW

This is the plug for the engine harness and wires up sensors – it plays no part in CC but I have it pictured here for your demonstration. This has two wires out of either side and it’s the first plug you see that you have to slide a plastic cover across to disconnect. Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Delphi Plug Diassembly and Pin Wiring Process: THIS IS THE SAME PLUG AS THE CORSA C (ITS FROM AN ASTRA H) BUT DISREGARD THE DIFFERENCE IN COLOUR.

^ THE DELPHI PLUG AS IT WILL BE IN SITU ^

1: Take the plug out of the ECU socket – it can be stif. (As you pull back on the grey plastic handle, use a screwdriver to prise the slider out as well as you will break the handle doing it alone. 2: Make a decent amount of space to work on the plug around the engine

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

3: You need to remove the top cover of the plug – make sure the handle is pulled all the ways back otherwise the cover won’t come off. Then release the two lugs on each side by carefully prising with a precision screwdriver.

4: Slide the cover back towards the grey handle to remove from the final lug.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Notice that the back of the plug with the cover open has small numbers identifying the pins on the end of each row – this is useful for finding Pin 8 – (PIN 8 is arrowed).

5: To insert a pin – you need to remove the pin locking plastic – it is a small red/brown coloured device and you just prise it out with a precision screwdriver. 6: Find Pin 8 on the plug – notice there are small numberings on the side to help you locate the correct hole.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Note the small pin has a (tooth edge at the top) this locks it into place which is why when you feel resistance you may have the pin the wrong way round.

7: Take your pin and wire, and slide it (the correct way up) into the plug – usually they slide in with ease but if not a SMALL spray on the pin of WD40 will assist. If it won’t go in it maybe the wrong way round. Make sure you have soldered your new piece of wire that has enough length to travel to the drivers foot well before inserting the pin for your ease. 8: Reassemble remembering to carefully lock all the pins off using the red plastic retainer. 10: Place the plug back on the ecu pulling the handle back and gently tapping with a screwdriver on the slider until it locks into position.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car







Once you have got into the plug – gently pull a suitable wire with the pin intact – and then SOLDER, the main CC clutch switch wire you have passed into the engine bay onto it. You may have a hole in the top casing of the plug on removal (see first image on removal guide) – so if this is the case like mine, run a couple of strips of duct tape over it to keep it watertight. Ensure that the plug is assembled correctly! Finally with your wire in place; carefully INSULATE with special insulation tape or fabric tape along your cruise control wire so it does not short or get melted from any hot components as it will be more vulnerable to the elements than if it was installed from factory.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

STEP 5: OPCOM Programming You’ll need your cars security code in order to access the programming aspect of the body control module so have this ready! These guides should be pretty much the same for any Canbus compatible Vauxhall model from 2002 onwards.

2 SIMPLE PROGRAMMING STEPS From the main menu select diagnostics At vehicle identification menu select year, and on the next page select model. At the next page select Engine, and at next page engine code. Press programming button. Program variant configuration. Change the 'not present' cruise control to 'present' then press 'Perform coding go back and close down 'Engine' options and engine code windows. In system description select 'body' select 'BCM' select 'programming' select program variant configuration enter 4 digit security code keep pressing next until you come to the option 'cruise control' and change 'not' present to present. press 'program' and select yes. press 'back' then 'back' then 'close'

Should this process not work: OPCOM is not the most definitive answer in programming (as I found out – mine did not work initially) The only alternative is Vauxhall turning it on via TECH2. It is costly and they will charge you a minimum of 30 minutes labour approximately £35 – 55.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

OPCOM TROUBLESHOOTING Of all the steps involved, I found that getting it programmed was the hardest! Message: Could not load file CCORSAZ14XEP.var I had trouble programming CC with my OPCOM – there were only two things that worked for me. Run OPCOM 100219a in Windows XP (not Win 7 with compatibility but a computer with the REAL windows XP) with Firmware 1.44 for the engine step – on the Z14XEP it would not let me programme variant config – I had to select Z12XEP despite that fact it wasn’t my engine – this can be REALLY dangerous so don’t do it – although it worked for me. Cannot Access the Body Control Module For my Z14XEP the best way to get into the BCM was again using Windows XP (I tried Windows 7 and 8 with no success), using OPCOM firmware 1.39 and using the China Clone 2010)

Hints and Tips:    

Always check/ test your interface in Settings first to check it is working correctly Configure the software to your correct hardware revision Do not swap firmware from your original factory firmware unless you have to – it can damage the interface and this may have been my problem Don’t run the engine whilst programming – just have the ignition on (only for a max of 5 minutes)

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Wiring Diagrams and Relevant Materials:

Location of required ECU Plug – X53

Diagram of the Brake Switch Connector

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Diagrammatic representation of the X53 ECU plug and its layout

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Clutch Switch and Stop Switch Wiring Diagram from Top at Fuse 40 to wire leading to Pin 8 of the X53 ECU Delphi Connector.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

INFORMATION FOR XE Engines (Prefacelift

From what I can determine there is a good chance you can install Cruise Control on: Z14XE – Multec S (F) ECU – connect to Pin 8 Z18XE – Simtec 71 ECU – connect to Pin 10 Z10XEP – Motronic 7.6.1 – connect to Pin 8 From my knowledge the 1.8 engine is used across the Astra range and they come with an engine management system capable of cruise control and some SRI 1.8 models have the cruise control system fitted but that would need to be confirmed by someone who owns a Corsa C 1.8 with Cruise. There has been some success threads about installing in a Z14XE so for now I will say it is possible however; that is again subject to the ECU having the correct software.

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.

Author accepts no responsibility/ liability for damage/ accidents or losses following the use of this guidance during any cruise control modification – always have a qualified Vauxhall specialist technician modify your car

Thanks for taking the time to read the guide – remember you must be careful with engine wiring, brake lights and your personal safety! Be safe on the roads! DO NOT use your vehicle if you suspect damage has occurred resulting from a cruise control modification. Take it to your local approved Vauxhall Dealership for Diagnostics.

If you found this useful, the guidance worked for you or your need assistance with something see the thread http://www.corsa-c.co.uk/forum/showthread.php?402151-CruiseControl-Install

Before you use your Cruise Control system after fitting it from this guidance – you have to have it PROPERLY TESTED by a fully approved Vauxhall Specialist.