Descripción: This document describes the CPRI MUX feature, including its technical principles, related features, networ...
SingleRAN
CPRI MUX (LampSite) Feature Parameter Description Issue
01
Date
2015-03-23
HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd. Address:
Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China
Website:
http://www.huawei.com
Email:
[email protected]
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
i
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
Contents
Contents 1 About This Document.................................................................................................................. 1 1.1 Scope.............................................................................................................................................................................. 2 1.2 Intended Audience.......................................................................................................................................................... 2 1.3 Change History............................................................................................................................................................... 2
2 Overview......................................................................................................................................... 5 2.1 Introduction.................................................................................................................................................................... 6 2.2 Benefits........................................................................................................................................................................... 6
3 Dependencies on BBU Boards and RF Units........................................................................... 8 3.1 BBU3900 Boards Supporting CPRI MUX.....................................................................................................................9 3.2 BBU3910 Boards Supporting CPRI MUX...................................................................................................................10 3.3 RF Units Supporting CPRI MUX.................................................................................................................................11
4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution......................... 13 4.1 CPRI MUX for Co-MPT Multimode Base Stations.....................................................................................................14 4.1.1 Constraints................................................................................................................................................................. 14 4.1.2 CPRI MUX Networking Mode..................................................................................................................................14 4.2 CPRI MUX for Separate-MPT Multimode Base Stations............................................................................................16 4.2.1 Constraints................................................................................................................................................................. 16 4.2.2 CPRI MUX Networking Mode..................................................................................................................................16
5 CPRI MUX Topologies with BBU3910s Used in the LampSite Solution......................... 19 5.1 CPRI MUX for Co-MPT Multimode Base Stations.....................................................................................................20 5.1.1 Constraints................................................................................................................................................................. 20 5.1.2 CPRI MUX Networking Mode..................................................................................................................................20 5.2 CPRI MUX for Separate-MPT Multimode Base Stations............................................................................................21 5.2.1 Constraints................................................................................................................................................................. 21 5.2.2 CPRI MUX Networking Mode..................................................................................................................................21
6 Specifications of the CPRI MUX Feature................................................................................24 7 Related Features...........................................................................................................................44 8 Network Impact........................................................................................................................... 45 8.1 System Capacity........................................................................................................................................................... 46 8.2 Network Performance...................................................................................................................................................46 Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
ii
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
Contents
8.3 Reliability..................................................................................................................................................................... 46
9 Engineering Guidelines............................................................................................................. 48 9.1 When to Use CPRI MUX............................................................................................................................................. 49 9.2 Required Information................................................................................................................................................... 49 9.3 Planning........................................................................................................................................................................ 49 9.4 Deployment.................................................................................................................................................................. 50 9.4.1 Requirements............................................................................................................................................................. 50 9.4.2 Data Preparation........................................................................................................................................................ 50 9.4.3 Activation.................................................................................................................................................................. 54 9.4.4 Activation Observation..............................................................................................................................................56 9.4.5 Deactivation...............................................................................................................................................................57 9.4.6 Reconfiguration......................................................................................................................................................... 57 9.5 Performance Monitoring...............................................................................................................................................57 9.6 Parameter Optimization................................................................................................................................................ 57 9.7 Troubleshooting............................................................................................................................................................ 57 9.7.1 Related Alarms.......................................................................................................................................................... 58 9.7.2 MML Commands for Maintenance........................................................................................................................... 60
10 Reference Documents............................................................................................................... 63
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
iii
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
1
1 About This Document
About This Document
1.1 Scope 1.2 Intended Audience 1.3 Change History
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
1
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
1 About This Document
1.1 Scope This document describes the CPRI MUX feature, including its technical principles, related features, network impact, and engineering guidelines. The base stations mentioned in this document refer to DBS3900 base stations in the LampSite solution. Any managed objects (MOs), parameters, alarms, or counters described herein correspond to the software release delivered with this document. Any future updates will be described in the product documentation delivered with future software releases. GSM, UMTS, and LTE are abbreviated as G, U, and L, respectively.
1.2 Intended Audience This document is intended for personnel who: l
Need to understand the features described herein
l
Work with Huawei products
1.3 Change History This section provides information about the changes in different document versions. There are two types of changes: l
Feature change Changes in features and parameters of a specified version as well as the affected entities.
l
Editorial change Changes in wording or addition of information and any related parameters affected by editorial changes. Editorial change does not specify the affected entities.
SRAN9.0 05 (2015-03-25) This issue includes the following changes. Change Type
Change Description
Parameter Change
Feature change
Updated specifications of the CPRI MUX feature. For details, see 6 Specifications of the CPRI MUX Feature.
None
Editorial change
None
None
SRAN9.0 04 (2015-01-30) This issue includes the following changes. Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
2
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
1 About This Document
Change Type
Change Description
Parameter Change
Feature change
l Added pRRU3902. For details, see 3.3 RF Units Supporting CPRI MUX.
None
l Updated specifications of the CPRI MUX feature. For details, see 6 Specifications of the CPRI MUX Feature. Editorial change
None
None
SRAN9.0 03 (2014-08-30) This issue includes the following changes. Change Type
Change Description
Parameter Change
Feature change
Added the BBU3910A that supports CPRI MUX. For details, see the following sections:
None
l 3.2 BBU3910 Boards Supporting CPRI MUX l 5 CPRI MUX Topologies with BBU3910s Used in the LampSite Solution Editorial change
None
None
SRAN9.0 02 (2014-07-30) This issue includes the following changes.
Issue 01 (2015-03-23)
Change Type
Change Description
Parameter Change
Feature change
None
None
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
1 About This Document
Change Type
Change Description
Parameter Change
Editorial change
Revised the descriptions in the following chapters:
None
l 4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution l 6 Specifications of the CPRI MUX Feature
SRAN9.0 01 (2014-04-30) This issue does not include any changes.
SRAN9.0 Draft A (2014-02-28) This is a new document for SRAN9.0.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
4
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
2 Overview
2
Overview
2.1 Introduction 2.2 Benefits
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
5
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
2 Overview
2.1 Introduction The CPRI MUX feature enables data transmission of multiple modes (such as GSM, UMTS, and LTE) on a common public radio interface (CPRI) port. Figure 2-1 shows the working principle of CPRI MUX. A multimode RF unit is connected to a single-mode or multimode(1) baseband processing unit (BBP)/interface board through CPRI connection. Another single-mode or multimode(1) BBP/interface board is connected to the preceding BBP/interface board through the BBU backplane and indirectly communicates with the multimode RF unit. The BBP/interface board that is directly connected to the multimode RF unit is called the converging board, and the corresponding mode is called the converging party. The BBP/ interface board that is indirectly connected to the multimode RF unit is called the converged board, and the corresponding mode is called the converged party. In Figure 2-1, mode A is the converged party and mode B is the converging party. Figure 2-1 Working principle of CPRI MUX
NOTE
In the LampSite solution, a multimode RF unit indicates a combination of the RHUB and pRRU.
2.2 Benefits This feature provides the following benefits: l
Reduced costs on optical modules and fiber optic cables for newly deployed multimode base stations: Multiple modes can use a CPRI port to transmit data, reducing the number of required optical modules and fiber optic cables considerably.
l
Low engineering costs and short service interruption duration in refarming scenarios: A multimode RF unit uses a single CPRI cable at the initial phase. CPRI MUX enables newly deployed modes to reuse the existing multimode RF unit and CPRI cable in refarming scenarios.
l
Guaranteed coverage for cascaded multimode RF units: CPRI MUX allows multimode RF units to be cascaded to ensure indoor coverage of different floors or areas. The
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
6
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
2 Overview
LampSite solution supports only RHUB cascading and does not support pRRU cascading.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
7
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
3
3 Dependencies on BBU Boards and RF Units
Dependencies on BBU Boards and RF Units
This chapter describes BBU boards and RF units that support CPRI MUX. 3.1 BBU3900 Boards Supporting CPRI MUX 3.2 BBU3910 Boards Supporting CPRI MUX 3.3 RF Units Supporting CPRI MUX
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
8
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
3 Dependencies on BBU Boards and RF Units
3.1 BBU3900 Boards Supporting CPRI MUX Co-MPT Scenarios In co-MPT scenarios, either or both of UMTS and LTE can serve as the converging party or converged party. Table 3-1 lists BBU3900 boards that support the CPRI MUX feature in a co-MPT multimode base station and constraints on the slots of the converging and converged boards. Table 3-1 BBU3900 boards that support the CPRI MUX feature in a co-MPT multimode base station and constraints on networking Mod e
Converging Board
Slot of the Converging Board
Constraints on Networking
UL
WBBPf, LBBPd, UBBPd_U, UBBPd_L
Slot 2 or 3
A WBBPf or UBBPd_Ux must be configured in slot 2 or 3.
NOTE
If a baseband processing board is named UBBPd_A/B/C, "A", "B", "C" indicates the mode whose baseband resources are configured on this board, baseband resources of different modes are isolated by "/". For example, UBBPd_U/L indicates a UBBPd configured with UMTS baseband resources, LTE baseband resources.
Separate-MPT Scenarios In separate-MPT scenarios, only UMTS and LTE can serve as the converging party. Table 3-2 lists BBU3900 boards that support the CPRI MUX feature in a separate-MPT multimode base station and constraints on the slots of the converging and converged boards. Table 3-2 BBU3900 boards that support the CPRI MUX feature in a separate-MPT multimode base station and constraints on the slots of the converging and converged boards Mode
Converging Board
Slot of the Converging Board
Converged Board
Slot of the Converged Board
UL
WBBPf or UBBPd_U
Slot 2 or 3
LBBPd or UBBPd_L
An LBBPd must be installed in slot 3 or 2.
LBBPd or UBBPd_L
Slot 2 or 3
WBBPf or UBBPd_U
A WBBPf must be installed in slot 3 or 2.
Restrictions on Slot Cabling Restrictions on slot cabling are imposed to maximize the utilization of baseband resources when the network uses CPRI MUX. Following these restrictions, operators do not need to Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
9
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
3 Dependencies on BBU Boards and RF Units
adjust the connections of boards or fiber optic cables in future capacity expansion (for example, capacity expansion from UMTS Only or LTE Only to UMTS+LTE). l
If a UBBPd is to be installed with a WBBPf or LBBPd, install the UBBPd in slot 2 or 3 and the LBBPd3 in slot 1. It is recommended that the fiber optic cables be connected to slot 3 of the UBBPd.
l
If an LBBPd1 or LBBPd2 is to be installed with an LBBPd3, install the LBBPd3 preferentially in a switching slot(such as slot3) or slot1. It is recommended that the fiber optic cables be connected to slot 3.
l
If a WBBPf3 or WBBPf4 is to be installed with an LBBPd1, LBBPd2, or LBBPd3, install them in slots 2 and 3, which are switching slots. Install the LBBPd3 preferentially in slot 3 or 1. It is recommended that the fiber optic cables be connected to slot 3.
l
In UMTS Only scenarios, the fiber optic cables can be connected to slots 2 and 3. It is recommended that the fiber optic cables be connected to slot 3. Do not connect the fiber optic cables to other slots to prevent cable adjustment in future capacity expansion from UMTS Only to UMTS+LTE.
l
In LTE Only scenarios, the fiber optic cables can be connected to slots 0, 1, 2, 3, 4, and 5. It is recommended that the fiber optic cables be connected to slot 3 (preferred) and slot 2. Do not connect the fiber optic cables to other slots to prevent cable adjustment in future capacity expansion from LTE Only to UMTS+LTE.
l
In UMTS+LTE scenarios, the fiber optic cables can be connected only to slots 2 and 3. It is recommended that the fiber optic cables be connected to slot 3.
3.2 BBU3910 Boards Supporting CPRI MUX Co-MPT Scenarios In co-MPT scenarios, either or both of UMTS and LTE can serve as the converging party or converged party. Table 3-3 lists BBU3910 boards that support the CPRI MUX feature in a co-MPT multimode base station and constraints on the slots of the converging and converged boards. Table 3-3 BBU3910 boards that support the CPRI MUX feature in a co-MPT multimode base station Mode
Converging Board
Slot of the Converging Board
UL
UBBPd_U/L
Slot0~Slot5
Separate-MPT Scenarios In separate-MPT scenarios, only UMTS and LTE can serve as the converging party. Table 3-4 lists BBU3910 boards that support the CPRI MUX feature in a separate-MPT multimode base station and constraints on the slots of the converging and converged boards.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
10
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
3 Dependencies on BBU Boards and RF Units
Table 3-4 BBU3910 boards that support the CPRI MUX feature in a separate-MPT multimode base station Mode
Converging Board
Slot of the Converging Board
Converged Board
Slot of the Converged Board
UL
UBBPd_U
Slot0~Slot5
UBBPd_L
Slot0~Slot5
UBBPd_L
Slot0~Slot5
UBBPd_U
Slot0~Slot5
Restrictions on Slot Cabling Restrictions on slot cabling are imposed to maximize the utilization of baseband resources when the network uses CPRI MUX. Following these restrictions, operators do not need to adjust the connections of boards or fiber optic cables in future capacity expansion (for example, capacity expansion from UMTS Only or LTE Only to UMTS+LTE). l
In the current release, the BBU3910 supports only the UBBPd serving as the baseband processing unit. The UBBPd can be installed in any slot. In separate-MPT scenarios, you are advised to install the baseband processing units of the same radio access technology in slots 2 and 3 so that the fiber optic cables can be connected to the two slots to support UMTS and LTE in future capacity expansion. In co-MPT scenarios, there are no such restrictions.
l
In UMTS Only scenarios, the fiber optic cables can be connected to slots 0, 1, 2, 3, 4, and 5. It is recommended that the fiber optic cables be connected to slot 3 (preferred) and slot 2. Do not connect the fiber optic cables to other slots to prevent cable adjustment in future capacity expansion from UMTS Only to UMTS+LTE.
l
In LTE Only scenarios, the fiber optic cables can be connected to slots 0, 1, 2, 3, 4, and 5. It is recommended that the fiber optic cables be connected to slot 3 (preferred) and slot 2. Do not connect the fiber optic cables to other slots to prevent cable adjustment in future capacity expansion from LTE Only to UMTS+LTE.
l
In UMTS+LTE scenarios, the fiber optic cables can be connected to slots 0, 1, 2, 3, 4, and 5. It is recommended that the fiber optic cables be connected to slot 3 (preferred) and slot 2. Do not connect the fiber optic cables to other slots.
3.3 RF Units Supporting CPRI MUX Table 3-5 lists RF units that support the CPRI MUX feature. Table 3-5 RF units that support CPRI MUX RF Unit
Issue 01 (2015-03-23)
Working Mode
CPRI MUX Support (Yes/No) Co-MPT
Separate-MPT
RHUB3908
UL
Yes
Yes
pRRU3901
UL
Yes
Yes
pRRU3902
UL
Yes
Yes
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
11
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
Issue 01 (2015-03-23)
3 Dependencies on BBU Boards and RF Units
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
12
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
4
4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution
CPRI MUX Topologies with BBU3900s Used in the LampSite Solution
This chapter describes CPRI MUX topologies in the LampSite solution for co-MPT multimode base stations and separate-MPT multimode base stations. 4.1 CPRI MUX for Co-MPT Multimode Base Stations 4.2 CPRI MUX for Separate-MPT Multimode Base Stations
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
13
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution
4.1 CPRI MUX for Co-MPT Multimode Base Stations 4.1.1 Constraints The converging and converged parties in the CPRI MUX feature must share one BBU.
4.1.2 CPRI MUX Networking Mode The following conditions must be met: l
A WBBPf, LBBPd, UBBPd_U, UBBPd_L can serve as the converging board and must be configured in slot 2 or 3.
l
A WBBPf or UBBPd_U must be configured in slot 2 or 3.
l
A BBU can connect to a maximum of 24 RHUBs. The RHUB connects to the BBU only in chain (single-link) topology. A BBU supports multiple RHUB chains. Each CPRI link supports a maximum of four levels of RHUB cascading.
l
When RHUBs and pRRUs work in branch chain (single-link) topology, an RHUB can connect to a maximum of eight pRRUs and the pRRUs do not support cascading.
l
When RHUBs and pRRUs work in branch load sharing topology, an RHUB can connect to a maximum of four pRRUs and the pRRUs do not support cascading.
Figure 4-1 shows UMTS+LTE CPRI MUX in branch chain (single-link) topology, where LTE serves as the converging party and UMTS serves as the converged party; the LBBPd/ UBBPd_L serves as the converging board and the WBBPf/UBBPd_U serves as the converged board.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
14
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution
Figure 4-1 UMTS+LTE CPRI MUX in co-MPT scenarios in branch chain (single-link) topology
Figure 4-2 shows UMTS+LTE CPRI MUX in branch load sharing topology, where LTE serves as the converging party and UMTS serves as the converged party; the LBBPd/ UBBPd_L serves as the converging board and the WBBPf/UBBPd_U serves as the converged board.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
15
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution
Figure 4-2 UMTS+LTE CPRI MUX in co-MPT scenarios in branch load sharing topology
4.2 CPRI MUX for Separate-MPT Multimode Base Stations 4.2.1 Constraints l
The converging and converged parties in the CPRI MUX feature must share one BBU.
l
One mode serves as either the converging party or the converged party but cannot serves as both parties. Data can be converged only to one converging board at a time.
l
One BBU can provide a maximum of six CPRI ports for data convergence, and these CPRI ports must be provided by the WBBPf, LBBPd, UBBPd_U, or UBBPd_L that is installed in slot 2 or 3.
4.2.2 CPRI MUX Networking Mode The following conditions must be met: l
A WBBPf, LBBPd, UBBPd_U, or UBBPd_L can serve as the converging board and must be configured in slot 2 or 3.
l
A WBBPf/UBBPd_U and an LBBPd/UBBPd_L must be configured in slot 2 and slot 3, respectively.
l
A BBU can connect to a maximum of 24 RHUBs. The RHUB connects to the BBU only in chain (single-link) topology. A BBU supports multiple RHUB chains. Each CPRI link supports a maximum of four levels of RHUB cascading.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
16
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution
l
When RHUBs and pRRUs work in branch chain (single-link) topology, an RHUB can connect to a maximum of eight pRRUs and the pRRUs do not support cascading.
l
When RHUBs and pRRUs work in branch load sharing topology, an RHUB can connect to a maximum of four pRRUs and the pRRUs do not support cascading.
Figure 4-3 shows UMTS+LTE CPRI MUX in branch chain (single-link) topology, where LTE serves as the converging party and UMTS serves as the converged party; the LBBPd/ UBBPd_L serves as the converging board and the WBBPf/UBBPd_U serves as the converged board. Figure 4-3 UMTS+LTE CPRI MUX in separate-MPT scenarios in branch chain (single-link) topology
Figure 4-4 shows UMTS+LTE CPRI MUX in branch load sharing topology, where LTE serves as the converging party and UMTS serves as the converged party; the LBBPd/ UBBPd_L serves as the converging board and the WBBPf/UBBPd_U serves as the converged board.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
17
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution
Figure 4-4 UMTS+LTE CPRI MUX in separate-MPT scenarios in load sharing topology
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
18
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
5
5 CPRI MUX Topologies with BBU3910s Used in the LampSite Solution
CPRI MUX Topologies with BBU3910s Used in the LampSite Solution
This chapter describes CPRI MUX topologies in the LampSite solution for co-MPT multimode base stations and separate-MPT multimode base stations. 5.1 CPRI MUX for Co-MPT Multimode Base Stations 5.2 CPRI MUX for Separate-MPT Multimode Base Stations
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
19
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
5 CPRI MUX Topologies with BBU3910s Used in the LampSite Solution
5.1 CPRI MUX for Co-MPT Multimode Base Stations 5.1.1 Constraints The converging and converged parties in the CPRI MUX feature must share one BBU.
5.1.2 CPRI MUX Networking Mode The following conditions must be met: l
A UBBPd_U, UBBPd_L can serve as the converging board and can be configured in slot 0~5.
l
A BBU can connect to a maximum of 24 RHUBs. The RHUB connects to the BBU only in chain (single-link) topology. A BBU supports multiple RHUB chains. Each CPRI link supports a maximum of four levels of RHUB cascading.
l
When RHUBs and pRRUs work in branch chain (single-link) topology, an RHUB can connect to a maximum of eight pRRUs and the pRRUs do not support cascading.
l
When RHUBs and pRRUs work in branch load sharing topology, an RHUB can connect to a maximum of four pRRUs and the pRRUs do not support cascading.
Figure 5-1 shows UMTS+LTE CPRI MUX in branch chain (single-link) topology, where LTE serves as the converging party and UMTS serves as the converged party; the UBBPd_L serves as the converging board and the UBBPd_U serves as the converged board. Figure 5-1 UMTS+LTE CPRI MUX in co-MPT scenarios in branch chain (single-link) topology
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
20
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
5 CPRI MUX Topologies with BBU3910s Used in the LampSite Solution
Figure 5-2 shows UMTS+LTE CPRI MUX in branch load sharing topology, where LTE serves as the converging party and UMTS serves as the converged party; the UBBPd_L serves as the converging board and the UBBPd_U serves as the converged board. Figure 5-2 UMTS+LTE CPRI MUX in co-MPT scenarios in branch load sharing topology
5.2 CPRI MUX for Separate-MPT Multimode Base Stations 5.2.1 Constraints The converging and converged parties in the CPRI MUX feature must share one BBU.
5.2.2 CPRI MUX Networking Mode The following conditions must be met: l
A UBBPd_U or UBBPd_L can serve as the converging board and can be configured in slot 0~5.
l
A BBU can connect to a maximum of 24 RHUBs. The RHUB connects to the BBU only in chain (single-link) topology. A BBU supports multiple RHUB chains. Each CPRI link supports a maximum of four levels of RHUB cascading.
l
When RHUBs and pRRUs work in branch chain (single-link) topology, an RHUB can connect to a maximum of eight pRRUs and the pRRUs do not support cascading.
l
When RHUBs and pRRUs work in branch load sharing topology, an RHUB can connect to a maximum of four pRRUs and the pRRUs do not support cascading.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
21
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
5 CPRI MUX Topologies with BBU3910s Used in the LampSite Solution
Figure 5-3 shows UMTS+LTE CPRI MUX in branch chain (single-link) topology, where LTE serves as the converging party and UMTS serves as the converged party; the UBBPd_L serves as the converging board and the UBBPd_U serves as the converged board. Figure 5-3 UMTS+LTE CPRI MUX in separate-MPT scenarios in branch chain (single-link) topology
Figure 5-4 shows UMTS+LTE CPRI MUX in branch load sharing topology, where LTE serves as the converging party and UMTS serves as the converged party; the UBBPd_L serves as the converging board and the UBBPd_U serves as the converged board.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
22
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
5 CPRI MUX Topologies with BBU3910s Used in the LampSite Solution
Figure 5-4 UMTS+LTE CPRI MUX in separate-MPT scenarios in load sharing topology
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
23
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6
6 Specifications of the CPRI MUX Feature
Specifications of the CPRI MUX Feature
In separate-MPT or co-MPT CPRI MUX scenarios, the converging capabilities of a multimode base station are determined by CPRI line rates and the capabilities of the converging party. Table 6-1 and Table 6-2 provide the converging capabilities of the converging party.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
24
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6 Specifications of the CPRI MUX Feature
Table 6-1 Converging capabilities of the converging party in multimode base stations enabled with CPRI MUX (LTE full compression) CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
Co-MPT
WBBPf/ LBBPd
2*LTE20MHz +UMTS 0*Cell
4*LTE20MHz+UMTS 0*Cell(20M/15M only)
Not supported
1*LTE20MHz +UMTS 1*Cell
3*LTE20MHz+UMTS 0*Cell(with different LTE bandwidths)
0*LTE20MHz +UMTS 3*Cell
2*LTE20MHz+UMTS 1*Cell
3*LTE10MHz +UMTS 0*Cell(10M only)
1*LTE20MHz+UMTS 3*Cell
2*LTE10MHz +UMTS 0*Cell(with different LTE bandwidths)
6*LTE10MHz+UMTS 0*Cell(10M only)
1*LTE10MHz +UMTS 1*Cell
3*LTE10MHz+UMTS 1*Cell
0*LTE10MHz +UMTS 3*Cell
2*LTE10MHz+UMTS 2*Cell
0*LTE20MHz+UMTS 6*Cell
5*LTE10MHz+UMTS 0*Cell(with different LTE bandwidths)
1*LTE10MHz+UMTS 3*Cell 0*LTE10MHz+UMTS 6*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
25
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
6 Specifications of the CPRI MUX Feature
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
UBBPd
2*LTE20MHz +UMTS 0*Cell
4*LTE20MHz+UMTS 0*Cell(20M/15M only)
1*LTE20MHz +UMTS 1*Cell
3*LTE20MHz+UMTS 0*Cell(with different LTE bandwidths)
8*LTE20MHz+UMTS 0*Cell(20M/15M only)
0*LTE20MHz +UMTS 3*Cell
2*LTE20MHz+UMTS 1*Cell
3*LTE10MHz +UMTS 0*Cell(10M only)
1*LTE20MHz+UMTS 3*Cell
2*LTE10MHz +UMTS 0*Cell(with different LTE bandwidths)
6*LTE10MHz+UMTS 0*Cell(10M only)
1*LTE10MHz +UMTS 1*Cell
3*LTE10MHz+UMTS 1*Cell
0*LTE20MHz+UMTS 13*Cell
0*LTE10MHz +UMTS 3*Cell
2*LTE10MHz+UMTS 2*Cell
12*LTE10MHz +UMTS 0*Cell(10M only)
0*LTE20MHz+UMTS 6*Cell
5*LTE10MHz+UMTS 0*Cell(with different LTE bandwidths)
1*LTE10MHz+UMTS 3*Cell 0*LTE10MHz+UMTS 6*Cell
6*LTE20MHz+UMTS 0*Cell(with different LTE bandwidths) 5*LTE20MHz+UMTS 1*Cell 4*LTE20MHz+UMTS 2*Cell 3*LTE20MHz+UMTS 4*Cell 2*LTE20MHz+UMTS 6*Cell 1*LTE20MHz+UMTS 9*Cell
10*LTE10MHz +UMTS 0*Cell(with different LTE bandwidths) 8*LTE10MHz+UMTS 1*Cell 7*LTE10MHz+UMTS 2*Cell 6*LTE10MHz+UMTS 3*Cell 5*LTE10MHz+UMTS 4*Cell 4*LTE10MHz+UMTS 5*Cell 3*LTE10MHz+UMTS 6*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
26
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
6 Specifications of the CPRI MUX Feature
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
2*LTE10MHz+UMTS 8*Cell 1*LTE10MHz+UMTS 10*Cell 0*LTE10MHz+UMTS 13*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
27
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6 Specifications of the CPRI MUX Feature
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
Separate -MPT
WBBPf/ LBBPd
2*LTE20MHz +UMTS 0*Cell
4*LTE20MHz+UMTS 0*Cell(20M/15M only)
5*LTE20MHz+UMTS 3*Cell
1*LTE20MHz +UMTS 1*Cell
3*LTE20MHz+UMTS 0*Cell(with different LTE bandwidths)
4*LTE20MHz+UMTS 5*Cell 3*LTE20MHz+UMTS 7*Cell
0*LTE20MHz +UMTS 3*Cell
2*LTE20MHz+UMTS 2*Cell
3*LTE10MHz +UMTS 0*Cell(10M only)
1*LTE20MHz+UMTS 5*Cell
2*LTE10MHz +UMTS 0*Cell(with different LTE bandwidths)
6*LTE10MHz+UMTS 0*Cell(10M only)
1*LTE10MHz +UMTS 2*Cell
4*LTE10MHz+UMTS 1*Cell
6*LTE10MHz+UMTS 5*Cell
0*LTE10MHz +UMTS 3*Cell
3*LTE10MHz+UMTS 2*Cell
5*LTE10MHz+UMTS 6*Cell
2*LTE10MHz+UMTS 4*Cell
4*LTE10MHz+UMTS 8*Cell
1*LTE10MHz+UMTS 5*Cell
3*LTE10MHz+UMTS 9*Cell
0*LTE10MHz+UMTS 6*Cell
2*LTE10MHz+UMTS 10*Cell
0*LTE20MHz+UMTS 6*Cell
5*LTE10MHz+UMTS 0*Cell(with different LTE bandwidths)
2*LTE20MHz+UMTS 9*Cell 1*LTE20MHz+UMTS 10*Cell 0*LTE20MHz+UMTS 10*Cell 8*LTE10MHz+UMTS 3*Cell 7*LTE10MHz+UMTS 4*Cell
1*LTE10MHz+UMTS 10*Cell 0*LTE10MHz+UMTS 10*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
28
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
6 Specifications of the CPRI MUX Feature
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
LBBPd Extende d
Not supported
Not supported
8*LTE20MHz+UMTS 0*Cell(20M/15M only) 6*LTE20MHz+UMTS 0*Cell(with different LTE bandwidths) 5*LTE20MHz+UMTS 3*Cell 4*LTE20MHz+UMTS 5*Cell 3*LTE20MHz+UMTS 7*Cell 2*LTE20MHz+UMTS 9*Cell 1*LTE20MHz+UMTS 10*Cell 0*LTE20MHz+UMTS 10*Cell 12*LTE10MHz +UMTS 0*Cell(10M only) 10*LTE10MHz +UMTS 0*Cell(with different LTE bandwidths) 9*LTE10MHz+UMTS 1*Cell 8*LTE10MHz+UMTS 3*Cell 7*LTE10MHz+UMTS 4*Cell 6*LTE10MHz+UMTS 5*Cell 5*LTE10MHz+UMTS 6*Cell 4*LTE10MHz+UMTS 8*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
29
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
6 Specifications of the CPRI MUX Feature
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
3*LTE10MHz+UMTS 9*Cell 2*LTE10MHz+UMTS 10*Cell 1*LTE10MHz+UMTS 10*Cell 0*LTE10MHz+UMTS 10*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
30
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
6 Specifications of the CPRI MUX Feature
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
UBBPd
2*LTE20MHz +UMTS 0*Cell
4*LTE20MHz+UMTS 0*Cell(20M/15M only)
1*LTE20MHz +UMTS 1*Cell
3*LTE20MHz+UMTS 0*Cell(with different LTE bandwidths)
8*LTE20MHz+UMTS 0*Cell(20M/15M only)
0*LTE20MHz +UMTS 3*Cell
2*LTE20MHz+UMTS 2*Cell
3*LTE10MHz +UMTS 0*Cell(10M only)
1*LTE20MHz+UMTS 5*Cell
2*LTE10MHz +UMTS 0*Cell(with different LTE bandwidths)
6*LTE10MHz+UMTS 0*Cell(10M only)
1*LTE10MHz +UMTS 2*Cell
4*LTE10MHz+UMTS 1*Cell
0*LTE20MHz+UMTS 13*Cell
0*LTE10MHz +UMTS 3*Cell
3*LTE10MHz+UMTS 2*Cell
12*LTE10MHz +UMTS 0*Cell(10M only)
0*LTE20MHz+UMTS 6*Cell
5*LTE10MHz+UMTS 0*Cell(with different LTE bandwidths)
2*LTE10MHz+UMTS 4*Cell 1*LTE10MHz+UMTS 5*Cell 0*LTE10MHz+UMTS 6*Cell
6*LTE20MHz+UMTS 0*Cell(with different LTE bandwidths) 5*LTE20MHz+UMTS 3*Cell 4*LTE20MHz+UMTS 5*Cell 3*LTE20MHz+UMTS 7*Cell 2*LTE20MHz+UMTS 9*Cell 1*LTE20MHz+UMTS 11*Cell
10*LTE10MHz +UMTS 0*Cell(with different LTE bandwidths) 9*LTE10MHz+UMTS 1*Cell 8*LTE10MHz+UMTS 3*Cell 7*LTE10MHz+UMTS 4*Cell 6*LTE10MHz+UMTS 5*Cell 5*LTE10MHz+UMTS 6*Cell 4*LTE10MHz+UMTS 8*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
31
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
6 Specifications of the CPRI MUX Feature
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
3*LTE10MHz+UMTS 9*Cell 2*LTE10MHz+UMTS 10*Cell 1*LTE10MHz+UMTS 12*Cell 0*LTE10MHz+UMTS 13*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
32
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6 Specifications of the CPRI MUX Feature
NOTE
l The converging capabilities of a CPRI link or a board and the CPRI link rate refer to those of the converging party. l The minimum CPRI line rate on the converging party is 2.5 Gbit/s. In the LampSite solution, the CPRI line rate of 4.9 Gbit/s or 9.8 Gbit/s is recommended. l The capabilities of the converging board cannot exceed the maximum capacity specifications of a site. For the maximum capacity specifications of a site, see Product Specifications > Technical Specifications of the BBU3900 > Capacity Specifications in LampSite Technical Description. l Converging capabilities in Table 6-1 apply to common cells. For the impact of different features on cell capacity, see the corresponding feature parameter description. l Table 6-1 lists the number of UMTS cells supported when the antenna capability is 1T2R. l Table 6-1 lists the number of LTE 20 MHz cells supported in the 2T2R antenna configuration, 20 MHz cell bandwidth, and 2:1 compression configuration for CPRI bandwidth. l Table 6-1 lists the number of LTE 10 MHz cells supported in the 2T2R antenna configuration, 10 MHz cell bandwidth, and 3:2 compression configuration for CPRI bandwidth. l Table 6-1 lists the converging capability of the LBBPd extended board at 9.8 Gbit/s in separateMPT mode when the LBBPd board enables the extended mode. CPRI extension mode is enabled through CPRIEX in the MOD BBP or LST BBP command. CPRI extension mode only affects the bandwidth specifications of the LBBPd at 9.8 Gbit/s in CPRI compression mode. For details, see BBU Hardware Description > BBU3900 and BBU3910 Hardware Description > BBU3900 and BBU3910 Boards > LBBP in 3900 Series Base Station Product Documentation. l The WBBPf3 board supports CPRI line rates of 4.9 Gbit/s, 6.144 Gbit/s, and 9.8 Gbit/s, but the RHUB does not support 6.144 Gbit/s. Table 6-1 does not list the CPRI line rate of 6.144 Gbit/s for the WBBPf3 board because this rate is not applicable when the WBBPf3 board is connected to the RHUB. l In separate-MPT scenarios, the LBBPd board supports CPRI extension mode. In CPRI extension mode, LTE bandwidth compression must be used. For example, a 5 MHz or 10 MHz bandwidth uses 3:2 compression and a 15 MHz or 20 MHz bandwidth uses 2:1 compression for LTE cells. l In separate-MPT scenarios, when the LBBPd board at a CPRI line rate of 9.8 Gbit/s does not enable CPRI extension mode, LTE bandwidth compression and non-compression cannot be configured on the same CPRI link. l In co-MPT scenarios, the LBBPd board does not support CPRI extension mode. l LTE in Table 6-1 supports TDD, FDD, and FDD+TDD. Note that LTE TDD 5 MHz does not support bandwidth compression but LTE FDD 5 MHz supports 3:2 bandwidth compression. Bandwidth combinations in this table do not support LTE TDD 5 MHz. Table 6-2 lists bandwidth combinations for LTE TDD 5 MHz. l "With different LTE bandwidths" in the table indicates that an LTE cell of a smaller bandwidth exists in addition to the bandwidths specified in a combination. In the combination of 6 x LTE 20 MHz + UMTS 0 x cell (with different LTE bandwidths), an LTE cell of 10 MHz or 5 MHz exists in addition to at least one 20 MHz bandwidth specified in the combination. Unless otherwise stated, a combination supports different LTE bandwidths. LampSite supports only LTE cells of 5 MHz or higher. Therefore, LTE 5 MHz in the combinations does not include other bandwidths.
Capacity specifications for each mode with different configurations are calculated as follows: l
l
UMTS –
The number of cells supported when the antenna capability is 1T1R is the same as that supported when the antenna capability is 2T2R.
–
The antenna capability is inversely proportional to the number of cells. For example, the number of cells supported when the antenna capability is 1T1R is twice that supported when the antenna capability is 2T2R.
LTE –
Issue 01 (2015-03-23)
When LTE cells have the same antenna capability and CPRI line rate, the number of 5 MHz or 10 MHz cells supported is inversely proportional to the bandwidth of Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
33
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6 Specifications of the CPRI MUX Feature
cells. For example, the number of cells supported by a 5 MHz cell is twice that supported by a 10 MHz cell. LTE 5 MHz cells and 10 MHz cells use the same compression configuration 3:2.
Issue 01 (2015-03-23)
–
When LTE cells have the same antenna capability and CPRI line rate, 15- and 20MHz cells support the same number of cells.
–
When LTE cells have the same bandwidth, the number of cells supported by 1T2R and 2T2R antennas is the same.
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
34
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6 Specifications of the CPRI MUX Feature
Table 6-2 Converging capabilities of the converging party in multimode base stations enabled with CPRI MUX (LTE full non-compression/compression and non-compression) CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
Co-MPT
WBBPf/ LBBPd
1*LTE20MHz +UMTS 0*Cell
2*LTE20MHz+UMTS 0*Cell
Not supported
0*LTE20MHz +UMTS 3*Cell
1*LTE20MHz+UMTS 1*Cell
2*LTE10MHz +UMTS 0*Cell 1*LTE10MHz +UMTS 1*Cell 0*LTE10MHz +UMTS 3*Cell 4*LTE5MHz +UMTS 0*Cell(Noncompression only) 3*LTE5MHz +UMTS 0*Cell(Compres sion and noncompression)
0*LTE20MHz+UMTS 6*Cell 4*LTE10MHz+UMTS 0*Cell(Noncompression+10M only) 3*LTE10MHz+UMTS 0*Cell(Compression/ non-compression with different LTE bandwidths) 2*LTE10MHz+UMTS 1*Cell 1*LTE10MHz+UMTS 3*Cell 0*LTE10MHz+UMTS 6*Cell
2*LTE5MHz +UMTS 1*Cell
8*LTE5MHz+UMTS 0*Cell(Noncompression only)
1*LTE5MHz +UMTS 2*Cell
6*LTE5MHz+UMTS 0*Cell(Compression and non-compression)
0*LTE5MHz +UMTS 3*Cell
4*LTE5MHz+UMTS 1*Cell 3*LTE5MHz+UMTS 2*Cell 2*LTE5MHz+UMTS 3*Cell 0*LTE5MHz+UMTS 6*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
35
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
6 Specifications of the CPRI MUX Feature
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
UBBPd
1*LTE20MHz +UMTS 0*Cell
2*LTE20MHz+UMTS 0*Cell
4*LTE20MHz+UMTS 0*Cell
0*LTE20MHz +UMTS 3*Cell
1*LTE20MHz+UMTS 1*Cell
3*LTE20MHz+UMTS 1*Cell(with different LTE bandwidths)
2*LTE10MHz +UMTS 0*Cell 1*LTE10MHz +UMTS 1*Cell 0*LTE10MHz +UMTS 3*Cell 4*LTE5MHz +UMTS 0*Cell(Noncompression only) 3*LTE5MHz +UMTS 0*Cell(Compres sion/ noncompression) 2*LTE5MHz +UMTS 1*Cell 1*LTE5MHz +UMTS 2*Cell 0*LTE5MHz +UMTS 3*Cell
0*LTE20MHz+UMTS 6*Cell 4*LTE10MHz+UMTS 0*Cell(Noncompression+10M only) 3*LTE10MHz+UMTS 0*Cell(Compression/ non-compression with different LTE bandwidths) 2*LTE10MHz+UMTS 1*Cell 1*LTE10MHz+UMTS 3*Cell 0*LTE10MHz+UMTS 6*Cell 8*LTE5MHz+UMTS 0*Cell(Noncompression only) 6*LTE5MHz+UMTS 0*Cell(Compression/ non-compression) 4*LTE5MHz+UMTS 1*Cell 3*LTE5MHz+UMTS 2*Cell 2*LTE5MHz+UMTS 3*Cell 0*LTE5MHz+UMTS 6*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
2*LTE20MHz+UMTS 3*Cell 1*LTE20MHz+UMTS 6*Cell 0*LTE20MHz+UMTS 13*Cell 8*LTE10MHz+UMTS 0*Cell(10M only) 6*LTE10MHz+UMTS 0*Cell(with different LTE bandwidths) 5*LTE10MHz+UMTS 2*Cell 4*LTE10MHz+UMTS 3*Cell 3*LTE10MHz+UMTS 5*Cell 2*LTE10MHz+UMTS 6*Cell 1*LTE10MHz+UMTS 9*Cell 0*LTE10MHz+UMTS 13*Cell 16*LTE5MHz+UMTS 0*Cell 13*LTE5MHz+UMTS 1*Cell 10*LTE5MHz+UMTS 2*Cell 8*LTE5MHz+UMTS 3*Cell
36
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
6 Specifications of the CPRI MUX Feature
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
7*LTE5MHz+UMTS 4*Cell 5*LTE5MHz+UMTS 6*Cell 4*LTE5MHz+UMTS 7*Cell 2*LTE5MHz+UMTS 8*Cell 1*LTE5MHz+UMTS 10*Cell 0*LTE5MHz+UMTS 13*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
37
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6 Specifications of the CPRI MUX Feature
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
Separate -MPT
WBBPf/ LBBPd
1*LTE20MHz +UMTS 0*Cell
2*LTE20MHz+UMTS 0*Cell
4*LTE20MHz+UMTS 0*Cell
0*LTE20MHz +UMTS 3*Cell
1*LTE20MHz+UMTS 3*Cell
3*LTE20MHz+UMTS 3*Cell
0*LTE20MHz+UMTS 6*Cell
2*LTE20MHz+UMTS 6*Cell
4*LTE10MHz+UMTS 0*Cell(Noncompression+10M only)
1*LTE20MHz+UMTS 10*Cell
2*LTE10MHz +UMTS 0*Cell 1*LTE10MHz +UMTS 1*Cell 0*LTE10MHz +UMTS 3*Cell 4*LTE5MHz +UMTS 0*Cell(Noncompression only) 3*LTE5MHz +UMTS 0*Cell(Compres sion/ noncompression) 2*LTE5MHz +UMTS 1*Cell 1*LTE5MHz +UMTS 2*Cell 0*LTE5MHz +UMTS 3*Cell
3*LTE10MHz+UMTS 0*Cell(Compression/ non-compression with different LTE bandwidths) 2*LTE10MHz+UMTS 2*Cell 1*LTE10MHz+UMTS 5*Cell 0*LTE10MHz+UMTS 6*Cell 8*LTE5MHz+UMTS 0*Cell(Noncompression only) 6*LTE5MHz+UMTS 0*Cell(Compression/ non-compression) 5*LTE5MHz+UMTS 1*Cell 4*LTE5MHz+UMTS 2*Cell 3*LTE5MHz+UMTS 3*Cell 2*LTE5MHz+UMTS 4*Cell 0*LTE5MHz+UMTS 6*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
0*LTE20MHz+UMTS 10*Cell 8*LTE10MHz+UMTS 0*Cell(10M only) 6*LTE10MHz+UMTS 0*Cell(with different LTE bandwidths) 5*LTE10MHz+UMTS 3*Cell 4*LTE10MHz+UMTS 5*Cell 3*LTE10MHz+UMTS 7*Cell 2*LTE10MHz+UMTS 9*Cell 1*LTE10MHz+UMTS 10*Cell 0*LTE10MHz+UMTS 10*Cell 16*LTE5MHz+UMTS 0*Cell 14*LTE5MHz+UMTS 1*Cell 13*LTE5MHz+UMTS 2*Cell 12*LTE5MHz+UMTS 3*Cell
38
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
6 Specifications of the CPRI MUX Feature
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
11*LTE5MHz+UMTS 4*Cell 10*LTE5MHz+UMTS 5*Cell 8*LTE5MHz+UMTS 6*Cell 7*LTE5MHz+UMTS 7*Cell 6*LTE5MHz+UMTS 8*Cell 5*LTE5MHz+UMTS 9*Cell 4*LTE5MHz+UMTS 10*Cell 0*LTE5MHz+UMTS 10*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
39
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
6 Specifications of the CPRI MUX Feature
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
UBBPd
1*LTE20MHz +UMTS 0*Cell
2*LTE20MHz+UMTS 0*Cell
4*LTE20MHz+UMTS 0*Cell
0*LTE20MHz +UMTS 3*Cell
1*LTE20MHz+UMTS 3*Cell
3*LTE20MHz+UMTS 3*Cell
0*LTE20MHz+UMTS 6*Cell
2*LTE20MHz+UMTS 6*Cell
4*LTE10MHz+UMTS 0*Cell(Noncompression+10M only)
1*LTE20MHz+UMTS 10*Cell
3*LTE10MHz+UMTS 0*Cell(Compression/ non-compression with different LTE bandwidths)
8*LTE10MHz+UMTS 0*Cell(Noncompression+10M only)
2*LTE10MHz +UMTS 0*Cell 1*LTE10MHz +UMTS 1*Cell 0*LTE10MHz +UMTS 3*Cell 4*LTE5MHz +UMTS 0*Cell(Noncompression only) 3*LTE5MHz +UMTS 0*Cell(Compres sion/ noncompression) 2*LTE5MHz +UMTS 1*Cell 1*LTE5MHz +UMTS 2*Cell 0*LTE5MHz +UMTS 3*Cell
1*LTE10MHz+UMTS 5*Cell
6*LTE10MHz+UMTS 0*Cell(Compression/ non-compression with different LTE bandwidths)
0*LTE10MHz+UMTS 6*Cell
5*LTE10MHz+UMTS 3*Cell
8*LTE5MHz+UMTS 0*Cell(Noncompression only)
4*LTE10MHz+UMTS 5*Cell
2*LTE10MHz+UMTS 2*Cell
6*LTE5MHz+UMTS 0*Cell(Compression/ non-compression)
3*LTE10MHz+UMTS 7*Cell 2*LTE10MHz+UMTS 9*Cell
5*LTE5MHz+UMTS 1*Cell
1*LTE10MHz+UMTS 11*Cell
4*LTE5MHz+UMTS 2*Cell
0*LTE10MHz+UMTS 13*Cell
3*LTE5MHz+UMTS 3*Cell
16*LTE5MHz+UMTS 0*Cell(Noncompression only)
2*LTE5MHz+UMTS 4*Cell 0*LTE5MHz+UMTS 6*Cell Issue 01 (2015-03-23)
0*LTE20MHz+UMTS 13*Cell
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
12*LTE5MHz+UMTS 0*Cell(Compression/ non-compression) 40
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
CoMPT or Separat e-MPT
Baseba nd Process ing Board Providi ng CPRI Optical Ports
Converging Capabilities of A CPRI Link (2.5 Gbit/s)
6 Specifications of the CPRI MUX Feature
Converging Capabilities of A CPRI Link (4.9 Gbit/s)
Converging Capabilities of A CPRI Link (9.8 Gbit/s)
11*LTE5MHz+UMTS 1*Cell 10*LTE5MHz+UMTS 2*Cell 9*LTE5MHz+UMTS 3*Cell 8*LTE5MHz+UMTS 4*Cell 7*LTE5MHz+UMTS 5*Cell 6*LTE5MHz+UMTS 6*Cell 5*LTE5MHz+UMTS 7*Cell 4*LTE5MHz+UMTS 8*Cell 2*LTE5MHz+UMTS 11*Cell 1*LTE5MHz+UMTS 12*Cell 0*LTE5MHz+UMTS 13*Cell
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
41
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
6 Specifications of the CPRI MUX Feature
NOTE
l The converging capabilities of a CPRI link or a board and the CPRI link rate refer to those of the converging party. l The minimum CPRI line rate on the converging party is 2.5 Gbit/s. In the LampSite solution, the CPRI line rate of 4.9 Gbit/s or 9.8 Gbit/s is recommended. l The capabilities of the converging board cannot exceed the maximum capacity specifications of a site. For the maximum capacity specifications of a site, see Product Specifications > Technical Specifications of the BBU3900 > Capacity Specifications in LampSite Technical Description. l Converging capabilities in Table 6-2 apply to common cells. For the impact of different features on cell capacity, see the corresponding feature parameter description. l Table 6-2 lists the number of UMTS cells supported when the antenna capability is 1T2R. l Table 6-2 lists the number of LTE 20 MHz cells supported when the following configurations are applied: 2T2R antenna configuration, 20 MHz cell bandwidth, and CPRI bandwidth in noncompression only mode or mode coexistence of non-compression and 2:1 compression. Unless otherwise stated for the LTE 20 MHz cells, non-compression coexists with 2:1 compression. If the CPRI line rate of the WBBPf/LBBPd board is 9.8 Gbit/s, mode coexistence of non-compression and compression is not supported, no matter whether the base station works in separate-MPT scenarios or co-MPT scenarios; in this situation, data in the table is in non-compression only mode. The UBBPd board is free from this restriction. l Table 6-2 lists the number of LTE 10 MHz cells supported when the following configurations are applied: 2T2R antenna configuration, 10 MHz cell bandwidth, and CPRI bandwidth in non-compression only mode or mode coexistence of non-compression and 3:2 compression. Unless otherwise stated for the LTE 10 MHz cells, non-compression coexists with 3:2 compression. If the CPRI line rate of the WBBPf/LBBPd board is 9.8 Gbit/s, mode coexistence of non-compression and compression is not supported, no matter whether the base station works in separate-MPT scenarios or co-MPT scenarios; in this situation, data in the table is in non-compression only mode. The UBBPd board is free from this restriction. l Table 6-2 lists the number of LTE 5 MHz cells supported when the following configurations are applied: 2T2R antenna configuration, 5 MHz cell bandwidth, and CPRI bandwidth in noncompression only mode or mode coexistence of non-compression and 3:2 compression. Unless otherwise stated for the LTE 5 MHz cells, non-compression coexists with 3:2 compression. If the CPRI line rate of the WBBPf/LBBPd board is 9.8 Gbit/s, mode coexistence of non-compression and compression is not supported, no matter whether the base station works in separate-MPT scenarios or co-MPT scenarios; in this situation, data in the table is in non-compression only mode. The UBBPd board is free from this restriction. l In non-compression only mode or mode coexistence of non-compression and compression for an LTE network, the LBBPd board does not support CPRI extension mode. l LTE in Table 6-2 supports TDD, FDD, and FDD+TDD. Note that LTE TDD 5 MHz does not support bandwidth compression but LTE FDD 5 MHz supports 3:2 bandwidth compression. Bandwidth combinations in this table support LTE TDD 5 MHz. l "With different LTE bandwidths" in the table indicates that an LTE cell of a smaller bandwidth exists in addition to the bandwidths specified in a combination. In the combination of 6 x LTE 20 MHz + UMTS 0 x cell (with different LTE bandwidths), an LTE cell of 10 MHz or 5 MHz exists in addition to the 20 MHz bandwidth specified in the combination. Unless otherwise stated, a combination supports different LTE bandwidths. LampSite supports only LTE cells of 5 MHz or higher. Therefore, LTE 5 MHz in the combinations does not include other bandwidths.
Capacity specifications for each mode with different configurations are calculated as follows: l
Issue 01 (2015-03-23)
UMTS –
The number of cells supported when the antenna capability is 1T1R is the same as that supported when the antenna capability is 2T2R.
–
The antenna capability is inversely proportional to the number of cells. For example, the number of cells supported when the antenna capability is 1T1R is twice that supported when the antenna capability is 2T2R. Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
42
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
l
Issue 01 (2015-03-23)
6 Specifications of the CPRI MUX Feature
LTE –
When LTE cells have the same antenna capability and CPRI line rate, the number of 15- and 20-MHz cells supported is the same.
–
When LTE cells have the same bandwidth, the number of cells supported by 1T2R and 2T2R antennas is the same.
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
43
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
7 Related Features
7
Related Features
Prerequisite Features None
Mutually Exclusive Features None
Impacted Features None
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
44
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
8 Network Impact
8
Network Impact
8.1 System Capacity 8.2 Network Performance 8.3 Reliability
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
45
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
8 Network Impact
8.1 System Capacity No impact.
8.2 Network Performance No impact.
8.3 Reliability CPRI MUX in Separate-MPT Scenarios CPRI MUX in separate-MPT scenarios has the following impacts on system reliability: l
Operations or exceptions on the converging party Circuit switched (CS) and packet switched (PS) services of the converged party will be interrupted if a CPRI port of the converging party becomes faulty or if any of the following operations is performed by the converging party: –
Software reset or power-off reset on the main control board or the converging board
–
Blocking, removing and then inserting the main control board or the converging board
–
Commissioning a CPRI port on the converging board
In general, the service interruption lasts less than 3 minutes. In the worst case, the service interruption does not exceed 5 minutes. l
Operations or exceptions on the converged party –
Performing software reset on the main control board: The data rate of PS services of the converging party may be reduced for less than 3s and the longest duration of rate reduction does not exceed 10s. CS services remain normal in this situation.
–
Performing power-off reset, inserting and then removing the main control board: CS and PS services on the converging party will be interrupted for less than 1 minute in general. In the worst case, the service interruption does not exceed 3 minutes.
CPRI MUX in Co-MPT Scenarios CPRI MUX in co-MPT scenarios has the following impacts on system reliability: l
CS and PS services of the converged party will be interrupted if a CPRI port of the converging party becomes faulty or if any of the following operations is performed by the converging party: –
Software reset or power-off reset on the converging board
–
Blocking, removing and then inserting the converging board
–
Commissioning a CPRI port on the converging board
In general, the service interruption lasts less than 3 minutes. In the worst case, the service interruption does not exceed 5 minutes. l
Issue 01 (2015-03-23)
If the WBBPf converges data, cells on the converged party will become unavailable for less than 5 minutes when a UMTS application is deleted or reset. Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
46
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
8 Network Impact
l
If the LBBPd converges data, cells on the converged party will become unavailable for less than 5 minutes when an LTE application is deleted or reset.
l
When a UBBPd serves as the converging board, deleting or resetting the applications of the modes configured on this board does not affect the converged party.
l
Adding baseband resources to one mode on a UBBPd interrupts services of other modes on this UBBPd, but does not affect services of the converged party that communicates with this UBBPd through the BBU backplane. NOTE
The service interruption period does not include the time required for manual operations, such as blocking, removing, and inserting boards.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
47
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9
9 Engineering Guidelines
Engineering Guidelines
This chapter describes how to implement the CPRI MUX feature. 9.1 When to Use CPRI MUX 9.2 Required Information 9.3 Planning 9.4 Deployment 9.5 Performance Monitoring 9.6 Parameter Optimization 9.7 Troubleshooting
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
48
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
9.1 When to Use CPRI MUX You can enable the CPRI MUX feature in the following scenarios: l
Sites in which a single-mode base station is to be evolved into a multimode base station and the operator requires that the existing topology of fiber optic cables remain unchanged to reduce engineering costs
l
Sites in which a co-MPT dual-mode or multimode base station is to be deployed and the operator requires that costs of fiber optic cables be reduced
l
Sites whose coverage must be ensured through cascaded RF units, such as stadiums, subways, and high-speed railways
9.2 Required Information The following information must be collected before feature deployment: l
Names of baseband processing units that are to be used in CPRI MUX
l
Names of RF units that are to be used in CPRI MUX
l
Information about optical modules
l
Planned site capacity
9.3 Planning RF Planning N/A
Network Planning Perform network planning according to 4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution.
Hardware Planning When selecting boards and RF units that are to be used in the CPRI MUX feature, you must consider the application scenarios and constraints provided in 3 Dependencies on BBU Boards and RF Units and 4 CPRI MUX Topologies with BBU3900s Used in the LampSite Solution.
NOTICE The CPRI link rates of baseband processing units/interface boards, optical modules, and RF units must match each other and meet the specifications in 6 Specifications of the CPRI MUX Feature.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
49
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
9.4 Deployment 9.4.1 Requirements Hardware RF units have been installed. Cables between RF units and BBUs have been connected as required by the CPRI MUX feature. For detailed installation procedures, see the corresponding Base Station Installation Guide and Site Maintenance Guide of the base stations. NOTE
If CPRI MUX is to be deployed in a site where a single-mode base station is to be evolved into a multimode base station, the hardware configuration must meet the requirements of CPRI MUX. Otherwise, replace the hardware.
License None
9.4.2 Data Preparation l
l
Issue 01 (2015-03-23)
The following table describes the parameters related to the RRUCHAIN MO for configuring the RHUB chain. Parameter Name
Parameter ID
Remarks
Data Source
Topo Type
TT
Set this parameter to CHAIN.
Network plan (negotiation not required)
Backup Mode
BM
Set this parameter to COLD.
Network plan (negotiation not required)
The following table describes the parameters related to the RHUB MO for configuring the RHUB. Parameter Name
Parameter ID
Remarks
Data Source
RHUB Chain No.
RCN
Set this parameter to the number of the RHUB chain onsite.
Network plan (negotiation not required)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
50
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
l
9 Engineering Guidelines
Parameter Name
Parameter ID
Remarks
Data Source
RHUB Position
PS
This parameter specifies the position of an RHUB on an RHUB chain or ring. For example, set this parameter to 0 for the firstlevel RHUB and 1 for the second-level RHUB.
Network plan (negotiation not required)
The following table describes the parameters related to the RRUCHAIN MO for configuring the pRRU chain. Parameter Name
Parameter ID
Remarks
Data Source
Topo Type
TT
Set this parameter to CHAIN.
Network plan (negotiation not required)
Backup Mode
BM
Set this parameter to COLD.
Network plan (negotiation not required)
NOTE This parameter is required only when the RHUBs and pRRUs work in branch chain (single-link) topology.
l
Issue 01 (2015-03-23)
The following table describes the parameters related to the RRU MO for configuring the pRRU. Parameter Name
Parameter ID
Remarks
Data Source
RRU Chain No.
RCN
Set this parameter to the number of the pRRU chain onsite.
Network plan (negotiation not required)
RRU Position
PS
Set this parameter to 0.
Network plan (negotiation not required)
RRU type
RT
Set this parameter to MPMU.
Network plan (negotiation not required)
RRU Topo Position
TP
Set this parameter to BRANCH.
Network plan (negotiation not required)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
51
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
Parameter Name
Parameter ID
Remarks
Data Source
RF Unit Working Mode
RS
l In Branch Chain (Single-Link) Topology, set this parameter to UO(UMTS_ONLY), TDL(LTE_TDD), LO(LTE_FDD), or UL(UMTS_LTE).
Network plan (negotiation not required)
l In Branch Load Sharing Topology, set this parameter to TDL(LTE_TDD), LO(LTE_FDD), or UL(UMTS_LTE).
CPRI MUX in Separate-MPT Scenarios Multimode RF units that work in multiple modes must follow the following configuration rules: l
RF units are configured and monitored by each mode.
l
RF units working in the same mode must have the same configuration. Otherwise, ALM-26274 Inter-System Board Object Configuration Conflict will be reported.
l
Table 9-1 lists parameters that must have the same configuration when CPRI MUX is deployed in separate-MPT scenarios.
Table 9-1 Configuration of common parameters Parameter Name on the UMTS/LTE Side
Parameter ID on the UMTS/LTE Side
Topo Type
TT
Cabinet No.
CN
Subrack No.
SRN
Slot No.
SN
RRU Type
RT
RRU Work Standard
RS
The RHUB/pRRU configuration of the converged party takes effect only after RHUB/pRRUs of the converging party have been configured. Before activating CPRI MUX, configure the RRUCHAIN MO on the converged party (UMTS or LTE). The key parameters are listed in Table 9-2. Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
52
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
Table 9-2 Parameters to be configured on the converged party Parameter Name
Parameter ID
Remarks (Configuration Principle for Different Scenarios)
Data Source
Access Type
AT
Set this parameter to PEERPORT.
Engineering Design
Head Cabinet No.
HCN
Engineering Design
Head Subrack No.
HSRN
Head Slot No.
HSN
Set these parameters to the cabinet number, subrack number, slot number, and optical port number of the CPRI port on the baseband board of the peer end, respectively.
Head Port No.
HPN
Local Slot No.
LSN
Engineering Design Engineering Design Engineering Design
If a BBU3900 is used, the slot number for the converged board does not need to be configured. In this case, set this parameter to 255.
Equipment Planning
If a BBU3910 is used and CPRI MUX works in UMTS/LTE separate-MPT scenarios, set this parameter to the slot number for the converged board.
CPRI MUX in Co-MPT Scenarios In co-MPT scenarios, if the networking meets the requirements in 4.1.1 Constraints, CPRI MUX is supported by default. Activating this feature does not need software configurations. NOTE
When CPRI MUX is used in UMTS+LTE co-MPT scenarios where the LBBPd or WBBPf provides 9.8 Gbit/s CPRI optical ports, run the ADD RRUCHAIN command to set the CPRI line rate to 4.9 Gbit/s. In co-MPT scenarios, the LBBPd board does not support CPRI extension mode.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
53
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
9.4.3 Activation Using MML Commands Step 1 On the converging party, run the ADD RRUCHAIN command to add an RHUB chain. Step 2 On the converging party, run the ADD RHUB command to add an RHUB to the RHUB chain. Step 3 On the converging party, run the ADD RRUCHAIN command to configure the pRRU chain. Step 4 On the converging party, run the ADD RRU command to add a pRRU to the pRRU chain. Step 5 On the converged party, run the ADD RRUCHAIN command for UMTS or LTE to add an RHUB chain. Step 6 On the converged party, run the ADD RHUB command to add an RHUB to the RHUB chain. Step 7 On the converged party, run the ADD RRUCHAIN command for UMTS or LTE to configure the pRRU chain. Step 8 On the converged party, run the ADD RRU command for UMTS or LTE to add a pRRU to the pRRU chain. ----End NOTE
Data configurations must be the same for RRUs on the converging party and converged party. For detailed parameter settings, see Table 9-1. When configuring the parameter AT(UMTS NodeB,LTE FDD eNodeB,LTE TDD eNodeB) in separate-MPT scenarios, set the local port for the converging party and the peer port for the converged party. For details, see Table 9-2. In separate-MPT scenarios where the CPRI line rate is 9.8 Gbit/s, if the bandwidth compression mode is changed for a cell on a CPRI link, all cells on the CPRI link must be deactivated, reconfigured, and then activated.
Using the CME to Perform Single Configuration Set parameters on the CME according to the operation sequence in Table 9-3. For instructions on how to perform the CME single configuration, see CME Single Configuration Operation Guide. Table 9-3 Configuring parameters on the CME
Issue 01 (2015-03-23)
SN
MO
Parameter Name
Parameter ID
Notes
1
RRUCHAIN
Chain No.
RCN
Topo Type
TT
Access Type
AT
Add an RRU chain on the converging party side.
Head Cabinet No.
HCN
Head Subrack No.
HSRN
Head Slot No.
HSN
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
54
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
SN
2
3
4
5
6
Issue 01 (2015-03-23)
MO
RHUB
RRUCHAIN
RRU
RRUCHAIN
RHUB
9 Engineering Guidelines
Parameter Name
Parameter ID
Head Port No.
HPN
Cabinet No.
CN
Subrack No.
SRN
Slot No.
SN
RRU Chain No.
RCN
RRU Position
PS
RHUB Name
RN
Chain No.
RCN
Topo Type
TT
Access Type
AT
Head Cabinet No.
HCN
Head Subrack No.
HSRN
Head Slot No.
HSN
Head Port No.
HPN
Cabinet No.
CN
Subrack No.
SRN
Slot No.
SN
RRU Chain No.
RCN
RRU Type
RT
RF Unit Working Mode
RS
Chain No.
RCN
Topo Type
TT
Access Type
AT
Head Cabinet No.
HCN
Head Subrack No.
HSRN
Head Slot No.
HSN
Head Port No.
HPN
Local Slot No.
LSN
Cabinet No.
CN
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Notes
Add an RHUB to the RRU chain on the converging party side.
Add an RRU chain on the converging party side.
Add a pRRU to the RRU chain on the converging party side.
Add an RRU chain on the converged party side for UMTS/ LTE.
Add an RHUB to the RRU
55
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
SN
MO
7
RRUCHAIN
8
RRU
9 Engineering Guidelines
Parameter Name
Parameter ID
Notes
Subrack No.
SRN
Slot No.
SN
chain on the converged party side.
RRU Chain No.
RCN
RRU Position
PS
RHUB Name
RN
Chain No.
RCN
Topo Type
TT
Access Type
AT
Head Cabinet No.
HCN
Head Subrack No.
HSRN
Head Slot No.
HSN
Head Port No.
HPN
Local Slot No.
LSN
Cabinet No.
CN
Subrack No.
SRN
Slot No.
SN
RRU Chain No.
RCN
RRU Type
RT
RF Unit Working Mode
RS
Add an RRU chain on the converged party side.
Add a pRRU to the RRU chain on the converged party side.
Using the CME to Perform Batch Modification This feature does not support batch modification using the CME.
9.4.4 Activation Observation After the configured data is activated, check whether RF unit-related alarms are reported on the Alarm/Event tab page of the RNC LMT, and eNodeB LMT. For details about RF unitrelated alarms, see 9.7.1 Related Alarms. Check whether the status of pRRUs is normal. l
Check whether the status of pRRUs is normal. –
Issue 01 (2015-03-23)
Separate-MPT scenarios Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
56
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
On the NodeB LMT or U2000, run the DSP BRD command to check whether RF units function properly. On the eNodeB LMT or U2000, run the DSP BRD command to check whether RF units function properly. –
Co-MPT scenarios On the BTS3900 LMT or U2000, run the DSP BRD command to check whether RF units function properly.
l
Check whether the line rate of the converging port is the same as planned. –
Separate-MPT scenarios On the LMT or U2000 of the converging party of a 3900 series base station, run the DSP CPRIPORT command to check whether the line rate of the converging port is the same as planned.
–
Co-MPT scenarios Run the DSP CPRIPORT command to check whether the line rate of the converging port is the same as planned.
9.4.5 Deactivation This feature does not need to be deactivated.
9.4.6 Reconfiguration Reconfiguration in the UL dual-mode branch chain (single-link) topology and UL dual-mode branch load sharing topology includes the following operations: l
Adding an RHUB to an RHUB chain
l
Adding a pRRU to an RHUB
l
Removing an RHUB from an RHUB chain
l
Removing a pRRU from an RHUB
For details about these operations, navigate to Engineering Guidelines (NodeB) > Deployment > Reconfiguration or Engineering Guidelines (eNodeB) > Deployment > Reconfiguration in RF Unit and Topology Management Feature Parameter Description.
9.5 Performance Monitoring N/A
9.6 Parameter Optimization N/A
9.7 Troubleshooting
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
57
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
9.7.1 Related Alarms Table 9-4 lists alarms related to the CPRI MUX feature. For detailed troubleshooting operations, see 3900 Series Multimode Base Station Alarm Reference. Table 9-4 CPRI MUX-related alarms Alarm ID
Alarm Name
Description
ALM-26215
Inter-Board Service Link Failure
This alarm is reported if inter-board communication fails in the BBU. Services of the converged party are affected.
ALM-26235
RF Unit Maintenance Link Failure
This alarm is reported if the maintenance link between the BBU and the RF unit malfunctions. The alarm is triggered by any of the following faults and is reported by the converged party in separateMPT scenarios: l Optical modules on the baseband board of the converging party become faulty. l Links used to forward data from the converged party to the converging party through the BBU backplane become faulty or resources are insufficient. l The baseband board of the converging party is not installed, powered on, configured or the baseband board experiences hardware failures. l The hardware capability of the baseband boards of the two parties is insufficient to support data converging through the BBU backplane. l Aggregation relationships are incorrectly configured.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
58
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
Issue 01 (2015-03-23)
9 Engineering Guidelines
Alarm ID
Alarm Name
Description
ALM-26270
Inter-System Communication Failure
In multi-mode configuration, this alarm is reported if the main control board in the current mode cannot communicate with the main control board in the other mode. If the two main control boards cannot communicate with each other for about 45s, this alarm is reported. If the two main control boards can communicate with each other for about 30s consecutively, this alarm is cleared.
ALM-26272
Inter-System RF Unit Parameter Settings Conflict
In multi-mode configuration, this alarm is reported if the parameter settings of an RF unit in a mode are inconsistent with those of the same RF unit in the other mode, such as the working mode or other RF parameters.
ALM-26274
Inter-System Board Object Configuration Conflict
In multi-mode configuration, this alarm is reported if the cabinet/ subrack/slot configuration of a board is inconsistent in different modes, the cabinet/ subrack/slot configuration of different boards is the same in different modes, or a board that supports only one mode is used by multiple modes at the same time.
ALM-26277
Inter-System Control Rights Conflict
In multi-mode configuration, this alarm is reported if the loading control rights are not configured or are inconsistent between different modes in the base station.
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
59
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
Alarm ID
Alarm Name
Description
ALM-26278
RF Unit Working Mode and Board Capability Mismatch
In multi-mode configuration, this alarm is reported if the configured working mode of an RF unit does not match the actual capability of the RF unit.
ALM-28203
Local Cell Unusable
ALM-28206
Local Cell Capability Decline
When CPRI MUX is implemented, multiple modes use one CPRI link to transmit data. As a result, bandwidth on the UMTS side may be insufficient and this alarm is reported.
ALM-29240
Cell Unavailable
ALM-29243
Cell Capability Degraded
When CPRI MUX is implemented, multiple modes use one CPRI link to transmit data. As a result, bandwidth on the LTE side may be insufficient and this alarm is reported.
NOTE
In separate-MPT scenarios, if a UMTS cell fails to be activated and EVT-28200 Iub Common Procedure Failure Indication is reported, check whether the UMTS+LTE cell configurations exceed the specifications of a single Ethernet cable. If so, modify the UMTS+LTE cell configurations. If not, run the BLK CPRIPORT command to block the CPRI_E port and then the UBL CPRIPORT command to unblock the CPRI_E port.
9.7.2 MML Commands for Maintenance In separate-MPT scenarios, the converging and converged parties have their own O&M platforms. In co-MPT scenarios, the converging and converged parties share the same O&M platform. Table 9-5 lists MML commands for maintenance. NOTE
After CPRI MUX is implemented, alarms will be reported if any exceptions occur. Clear the alarms according to the alarm reference.
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
60
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
9 Engineering Guidelines
Table 9-5 MML commands for maintenance MML Command
Application Scenario
Support by the Converging Party
Support by the Converged Party (Only in SeparateMPT Scenarios)
DSP RRUCHAIN
Use this command to query:
Fully supported
Fully supported
l Number of pRRUs/ RHUBs carried on an RRU chain or ring over an optical port on the converging party l Number of RHUB cascading levels. DSP RRUCHAINPH YTOPO
Use this command to query information about the pRRUs/RHUBs connected to the CPRI port.
Fully supported
Fully supported
DSP CPRIPORT
Use this command to query:
Fully supported
Partially supported: Use this command to query:
l Real-time data rates and other information about the optical port on the panel of the converging party
l Data rates on the CPRI port l Aggregation state
l Whether the optical port is in the aggregation state DSP CPRILBR
Use this command to query:
Fully supported
l Current CPRI line rate of the specified chain or ring l Maximum CPRI line rate of the baseband processing board
Partially supported: Use this command to query the line rate on the head and the end of the CPRI chain or ring. Other information is displayed as NULL.
l Maximum CPRI line rate of each RHUB on a chain or ring
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
61
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
MML Command
Application Scenario
Support by the Converging Party
Support by the Converged Party (Only in SeparateMPT Scenarios)
STR CPRILBRNEG
Use this command to start negotiation of the line rate on the optical port on the panel. Run this command if the RHUB chain cannot be set up or the chain cannot operate at the maximum line rate due to changes in parameter settings of the RHUB chain. Executing this command causes link disconnection, interrupting services.
Supported
Not supported
MOD RRUCHAIN
Use this command to set breakpoints on an RHUB chain.
Supported
Not supported
L: DSP CELL
Use this command to query the cell status. Cell setup fails and cell capability degrades when CPRI bandwidth is insufficient.
Supported
Supported
U: DSP ULOCELL
Issue 01 (2015-03-23)
9 Engineering Guidelines
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
62
SingleRAN CPRI MUX (LampSite) Feature Parameter Description
10
10 Reference Documents
Reference Documents
1.
3900 Series Base Station Technical Description
2.
3900 Series Multimode Base Station Alarm Reference
3.
3900 series base station installation guide package
4.
NodeB MML Command Reference
5.
eNodeB MML Command Reference
6.
RF Unit and Topology Management
7.
3900 series base station site maintenance guide package
Issue 01 (2015-03-23)
Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
63
