C5 Config BSI
Short Description
Download C5 Config BSI...
Description
INFO’ DIAG DIAGNOSTIC TOOLS
CITROËN
LEXIA PROXIA CD 41
CITROËN SELLING DEALERS:
AFTER SALES DIVISION
-
PDI technicians
-
Campaign co-ordinators
N° 421
AUTHORISED REPAIRERS: -
Service Managers
19/12/2008
- Consultant technicians THE CONTENTS OF THIS BULLETIN SHOULD BE MADE KNOWN TO ALL PERSONNEL WHO, DIRECTLY OR INDIRECTLY, USE LEXIA / PROXIA DIAGNOSTIC TOOLS.
TITLE: Manual configuration of the BSI ECU on CITROËN C5 (X7).
CONCERNING: The operations for configuring a BSI ECU: •
Following the replacement of an ECU,
•
Following the downloading of an ECU,
•
Checking the configuration.
IMPORTANT: Incorrect configuration will affect the operation of the vehicle. Follow the internet configuration procedure described in this document and limit the use of manual configuration just to the cases quoted in the INFO'DIAG.
Page 1 / 31
CONTENTS
1
Introduction………………………………….....………………………………………..3
2
Preliminaries………………………………………...……………………………………3 2.1 Safety advice………………………………………………………………………….3 2.2 Technical advice……….…..………………………………………………………..3
3 Operations to be carried out…………........………….….......………………………....4 3.1
Operations to be carried out before removal, downloading or
configuration of the BSI……………………………………........................................5
4
3.2
Operations to be carried out to configure the BSI…………………………..6
3.3
Operations to be carried out after the configuration of the BSI…………8
Checking of configuration……………………………………………………………..9 4.1
Notes on the configuration tables…………………………………....………..10
4.2
Configuration menus…………………………………………………………….10
4.3
Customer options…………………….…………………………………………..11
4.4
Configuration……………………….……………………………………………..12
4.5
ECUs present………………………………….………………………………….29
4.6
« VIN code » menu………………………………………………………………31
Page 2 / 31
1
INTRODUCTION Configuration is a sensitive operation, which has direct consequences on the correct operation of the vehicle. Incorrect configuration can have an impact on: •
Safety (deactivation of vehicle protection devices),
•
Overall functioning of the vehicle (complete loss of or damage to vehicle functions)
•
Vehicle diagnostics (returning of fault codes which may cause the diagnostic tool methods to fail, and lead to the unjustified removal of parts).
You are therefore requested to perform the configuration operation following the instructions on this INFO’DIAG in order to ensure customer satisfaction by returning their vehicle in a perfect operational state.
2
PRELIMINARIES The instructions below must be followed to guarantee safety linked to vehicle operation and well-being.
2.1 Safety advice Before starting the engine: •
Check that the electronic parking brake is activated,
•
If the gearbox is automatic, check that the gear lever is in position «P » (Park),
•
If the gearbox is manual, check that the gear lever is in neutral.
2.2 Technical advice The BSI must be correctly configured before initialising the BSI, initialising the keys or starting the engine.
Page 3 / 31
3
OPERATIONS TO BE CARRIED OUT This chapter describes the steps to be followed to configure a BSI. •
If the configuration is being carried out following the replacement of a BSI, or following the downloading of the BSI: follow chapters 3.1, 3.2 and 3.3.
•
If the configuration is being carried out independently of a BSI replacement, or the downloading of a BSI (checking the correct configuration of a vehicle for example): follow chapters 3.1 and 3.2 only. Chapter 3.1
Operation to be carried out before removal, downloading or configuration of the BSI: Printing of customer options configuration values È Chapter 3.2 Operations to be carried out to configure the BSI: È A) Configuration by internet È B) Choice of maintenance plan È C) Manual configuration of customer options È D) Checking of certain parameters with manual configuration È Chapter 3.3 Operations to be carried out after the configuration of the BSI: Initialisation of BSI (or initialisation of keys or synchronisation of high frequency remote controls)
Page 4 / 31
3.1 Operations to be carried out before removal, downloading or configuration of BSI Before removing the faulty BSI ECU, or downloading or configuring the ECU, establish communication with this ECU on the vehicle using the LEXIA or PROXIA diagnostic tool. Print the screen « Customer Options » from the diagnostic tool, showing the configuration parameter values (or note these values down manually). To do so, carry out the following operations: LEXIA or PROXIA 1
Connect the diagnostic tool on the vehicle.
2
Select "Diagnosis"
3
Enter the vehicle details, then its RPO number
4
Start the "Global Test"
5
Select the menu « BSI », then validate using key « * ».
6
Select the item « Configuration ».
7
Select the item « Manual configuration ».
8
Select the menu « CUSTOMER OPTIONS ».
9
Print the diagnostic tool screen showing the configuration parameter values, or note down these values by hand
10
Return to the Global Test by successive presses on the « Return » key.
Once this operation has been completed, you may replace or download the BSI, if required to do so.
Page 5 / 31
3.2 Operations to be carried out to configure the BSI A) Configuration by internet LEXIA
PROXIA
11
Select the menu « BSI », then validate using key « * ».
12
Select the item « Configuration ».
13
Select the item « Configuration by internet ».
14
Once the configuration parameters screen has appeared, validate using key « * ».
15
The list of configuration menus appears. Validate using key « F5 » to launch configuration by internet.
Check the accuracy of the vehicle’s VIN, then validate using key « * ».
To allow an internet connection, make the connections indicated on Once the tool has received the configuration data, return 16 the diagnostic tool then validate to the Proxia tool by validating with the « return » key. using key « * » to start configuration by internet. Successively select the menus: - « CONFIGURATION », - « ECUs PRESENT », - « VIN code ».
17
The list of configuration parameters appears. Validate using the key « * »
In the « CONFIGURATION » menu, select the submenus: - « Vehicle definition – Equipment – Driving information », - « Air conditioning – Cabin heating», - « Lighting – Signalling – Visibility – Rear view mirrors », - « Locking – Doors and tailgate – Immobiliser – Alarm », - « Fuel gauge law – Oil level gauge law ». In each sub-menu and in the ECUs present menu, validate using the « F5 » key to configure the parameters returned by the tool.
18
Return to the main menu of the BSI (« identification », « fault reading », etc.) with successive presses on the « return » key.
NOTE: If the configuration by internet does not work (presence of a message on the tool showing the error code linked to the phrase « it is pointless to repeat the operation »), carry out a manual configuration by replacing the internet configuration (based on the configuration tables in chapter 0), before continuing with the INFO’DIAG procedure from section B). NOTE: A monitoring of configuration failures is carried out centrally to correct any configuration malfunctions by internet. Page 6 / 31
B) Choice of maintenance plan LEXIA
PROXIA
19
Select the item « Maintenance – Operational Switch on the ignition. Select the item mode of BSI », « Maintenance – Operational mode of BSI », then validate with key « * ». then validate with key « * ».
20
Select the item « Maintenance », then validate with key « * ».
21
Select the item « Choice of maintenance plan (new vehicle preparation) ».
22
Follow the instructions given by the diagnostic tool: reply to the questions asked by the diagnostic tool.
23
Once the choice of maintenance plan procedure has been carried out, return to the main menu of the BSI (« identification », « fault reading »…) with successive presses on the « return » key.
C) Manual configuration of customer options Manually configure the «customer options » parameters, using the print-outs or notes previously made (chapter 3.1). LEXIA or PROXIA 24
Select the item « Configuration ».
25
Select the item « Manual configuration ».
26
Select the « CUSTOMER OPTIONS » menu.
27
Check (and modify if necessary), the values of each parameter, according to the values on the print-outs or notes.
28
Return to the main menu of the BSI (« identification », « fault reading », etc.) with successive presses on the « return » key.
D) Checking of certain parameters with manual configuration It is necessary to check certain configuration parameters (since the central base providing vehicle data may not be completely up to date). The parameters to check manually are shaded in grey in chapter 4. LEXIA or PROXIA Successively select the « CONFIGURATION », « ECUs PRESENT », and « VIN code » menus. In the « CONFIGURATION » menu select the sub-menus: - « Vehicle definition – Equipment – Driving information »,
29 - « Air conditioning – Cabin heating»,
- « Lighting – Signalling – Visibility – Rear view mirrors », - « Locking – Doors and tailgate – Immobiliser – Alarm », - « Fuel gauge law – Oil level gauge law ».
30
In each sub-menu and in the « ECUs present » and « VIN code » menus, check (and modify if necessary), the parameter values shaded in grey in the configuration tables (see chapter 4)
31
Return to the Global Test with successive presses on the « Return » key. Page 7 / 31
3.3 Operations to be carried out after the configuration of the BSI Operations to be carried out only if replacing or downloading a BSI: •
If the BSI has been replaced: initialise the new BSI ECU on the vehicle (« BSI initialisation »).
•
If the BSI has been downloaded, initialise the BSI ECU (« BSI initialisation »), or the keys, or simply synchronise the high frequency remote controls, depending on what is indicated in the procedure accompanying the recall campaign.
To carry out the initialisation operations, ALL of the customer’s keys and the confidential code card are required. LEXIA
PROXIA
32
Select the item « BSI », then validate using key « * ».
33
Select the item « Initialisation ».
34
Select the « BSI Initialisation » menu (or « Initialisation of keys »).
Select the « BSI Initialisation » menu (or « Initialisation of keys »).
35
Validate using key « * ».
36
Follow the instructions given by the diagnostic tool screens, in particular those displayed in the band at the bottom of the screen.
37
Return to the main menu of the BSI (« identification », « fault reading », etc.) with successive presses on the « return » key.
Once steps n° 32 to n° 37 have been completed, carry out the following operations to check that the vehicle is able to start. LEXIA
PROXIA
38
Select the item « BSI », then validate using key « * ».
39
Select the « Parameter Measures » menu of the BSI.
40
Select the sub-menu « Immobiliser ».
Select the item « pre-defined parameter screens », then select the sub-menu « Immobiliser ».
41
Check that the parameter « BSI matched to engine ECU » has the value « Yes ».
42
Check that the parameter « Engine ECU locked » has the value « No ».
43
Check that the parameter « Number of keys initialised » has the value « xx », where « xx » corresponds to the total number of the customer’s vehicle keys.
44
For each key, check that the parameter « Transponder label recognised » has the value « Yes ».
45
Return to the main menus screen of the tool (« diagnosis », « downloading», etc.) with successive presses on the « return » key. The diagnostic tool may be disconnected.
Page 8 / 31
4
CHECKING OF THE CONFIGURATION 4.1 Notes on the configuration tables The display of configuration parameters is conditional on their being present in the BSI software. The parameters will be displayed by the diagnostic tool partially or totally depending on the BSI software version. An underlined configuration value corresponds to the value to be programmed on all the vehicles.
Configuration notes: (1): Means that you have to programme the parameter according to the absence or presence of the option or to the vehicle definition. If the option or the vehicle definition is easily identifiable, the instruction is not accompanied by any particular text. (2): Means that you have to programme the value indicated in the column « Value to be configured ». This value is valid for all vehicles. It is prohibited to programme any other value. (3): Means that this parameter is programmed automatically when you use the procedure « CHOICE OF MAINTENANCE Plan (PRE-DELIVERY INSPECTION) »
Page 9 / 31
4.2
Configuration menus
After you have selected the menu « Manual configuration », the following menus are available: Menus
Pages
Customer options
11
Configuration
12
ECUs present
29
VIN code
31
NOTE: The parameters of the « Customer options » menu are also present in the configuration menu, it is therefore not necessary to configure these if the configuration of the parameters of the « Configuration » menu have been or will be carried out.
Page 10 / 31
4.3 Customer Options Configuration parameter
Multiplexed folding electric rear view mirrors Presence of rear screen wiping in reverse gear Type of deflation detection
Type of daytime-running lamps
Detection of driver's seat belt not fastened
Values to be configured No Yes Absent Present Absent Direct without display of pressures No daytime-running lamps Dedicated daytimerunning lamps
Comments Driver's door control pad with screenprinted . button Driver's door control pad with screenprinted button
.
Configure Present if a rear wiper is fitted. With rubber wheel valves. With metallic wheel valves. (1)
No
Value not to be configured except on the express request of the customer (deactivation of the alert for detection of driver’s seat belt not fastened).
Yes
(2)
No
For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
Yes
For all vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
No
For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
Yes
For all vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
Lighting by default of daytimerunning lamps
Simultaneous lighting of daytimerunning lamps and sidelamps
Page 11 / 31
4.4 Configuration Once the « Configuration » menu is selected, the following screen appears. Menus A
Contents VEHICLE DEFINITION – EQUIPMENT – DRIVER’S INFORMATION
Pages 13
B
AIR CONDITIONING – CABIN HEATING
20
C
LIGHTING – SIGNALLING – VISIBILITY – REAR VIEW MIRRORS
23
D
LOCKING – DOORS AND TAILGATE – IMMOBILISER – ALARM
26
E
FUEL GAUGE LAW - OIL GAUGE LAW
28
The content of each Menu is listed in the following chapters.
Page 12 / 31
4.4.1 Menu: vehicle definition – equipment – driving information (menu A) Configuration parameter (A)
Value to be configured
Comments All countries other than:
Overspeed alert for the Arabian peninsula
Absent
Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar. Countries Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar.
Present Passenger’s seat position memorisation control unit option Automatic gearbox option Right-hand-drive vehicle Variable damping suspension option
Absent Absent Present No Yes Absent Present
(2)
(1) (1) Configure « present » for vehicles fitted with hydropneumatic suspension with 3.0L petrol (XFV) or 2.7 L diesel (UHZ) engine. For engines:
Absent Engine oil temperature sensor option
1.8 L petrol (6FY),
•
2.0 L petrol (RFJ),
•
2.2 L diesel (4HP, 4HT).
For engines: Present
Absent Presence of the telematic unit (RT3/RT4)
•
Present
•
3.0 L petrol (XFV),
•
1.6 L diesel (9HZ),
•
2.0 L diesel (RHR),
•
2.7 L diesel (UHZ).
•
Without audio equipment,
•
RD4 radio/CD/MP3.
•
Telematic unit (RT4/RT5),
•
Telematic unit (NG4),
•
Radio navigation (RNEG).
Presence of water-indiesel-fuel sensor
Present
(1) The presence of the sensor for detecting water in the diesel fuel filter is visible thanks to the blue 3way connector on the diesel fuel filter.
Presence of air pump
Absent
(2)
Multifunction screen option
Present
(2)
Absent
Key: Parameter to be systematically checked after configuring by internet Page 13 / 31
Configuration parameter (A) Origin of the waterin-diesel-fuel information Driving position memorisation option Presence of a trailer relay unit (BSR) Presence and type of vehicle cruise control
Value to be configured
Comments
Engine ECU
(2)
Absent
Driver's seat with manual adjustment.
Present
Driver's seat with electric adjustment and memory.
No Yes Cruise control and speed limiter
Depending on the presence of a towbar. (2) For engines:
Engine ECU Origin of the oil temperature information
No Yes Absent
Type of parking assistance
Parking assistance with visual information Parking assistance with sound information Type of deflation detection
1.8 L petrol (6FY),
•
2.0 L petrol (RFJ),
•
2.2 L diesel (4HP, 4HT).
For engines: Engine Relay Unit
Presence of a parking assistance button
•
Rear Front and rear and available parking space No Yes No Yes Absent
•
3.0 L petrol (XFV),
•
1.6 L diesel (9HZ),
•
2.0 L diesel (RHR),
•
2.7 L diesel (UHZ).
Depending on the presence of the button (or the presence of sensors on the bumpers, front and rear) Without ultra-sonic sensors on the bumpers. With 4 ultra-sonic sensors on the rear bumper only. With 4 ultra-sonic sensors on the front and rear bumpers. Depending on the absence or presence of ultrasonic sensors on the rear bumper. Depending on the absence or presence of ultrasonic sensors on the rear bumper. With rubber wheel valves.
Direct without With metallic wheel valves. display of pressures
Type of detection of presence of fuel cap
No detection
If particle filter absent.
By the BSI
If particle filter present.
Piloting of the diesel
No particle filter
If particle filter absent.
Key: Parameter to be systematically checked after configuring by internet Page 14 / 31
Configuration parameter (A) fuel additive pump
Value to be configured Control by wire
Presence of available parking space warning lamp Total time before next maintenance
If particle filter present.
Standard
For vehicles except those fitted with a 2.0 L petrol (RHR) or 1.8 L petrol (6FY) engine.
Controlled
For vehicles fitted with a 2.0 L petrol (RHR) or 1.8 L petrol (6FY) engine.
Type of alternator Presence of available parking space button
Comments
No Yes No
(1)
(2) (3)
12 or 24 months
12 months for « severe » use of the vehicle. 24 months for « normal » use of the vehicle.
0 km
Configure 0 km for vehicles with an RPO number ≥ 11480 (14th April 2008) or for vehicles which have had their first service.
2500 km
Configure 2500 km for vehicles with an RPO number < 11480 and which have not had their first service.
Threshold for first service
Maintenance Speedometers in kilometres - CASE N°1 threshold (marketing) (3) For severe use and engines: 15 000 km
•
2.0 L petrol (RFJ),
•
1.6 L diesel (9HZ).
(3) For normal use and engines: •
2.0 L petrol (RFJ),
•
1.6 L diesel (9HZ).
For severe use and engines: 20 000 km
•
1.8 L petrol (6FY),
•
3.0 L petrol (XFV),
•
2.0 L diesel (RHR),
•
2.2 L diesel (4HP, 4HT),
•
2.7 L diesel (UHZ).
Key: Parameter to be systematically checked after configuring by internet Page 15 / 31
Configuration parameter (A)
Value to be configured
Comments (3) For normal use and engines:
30 000 km
•
1.8 L petrol (6FY),
•
3.0 L petrol (XFV),
•
2.0 L diesel (RHR),
•
2.2 L diesel (4HP, 4HT),
•
2.7 L diesel (UHZ).
Speedometers in miles - CASE N°2 (3) For severe use and engines: 16 000 km
•
2.0 L petrol (RFJ),
•
1.6 L diesel (9HZ).
(3) For normal use and engines: •
2.0 L petrol (RFJ),
•
1.6 L diesel (9HZ).
For severe use and engines: 20 000 km
•
1.8 L petrol (6FY),
•
3.0 L petrol (XFV),
•
2.0 L diesel (RHR),
•
2.2 L diesel (4HP, 4HT),
•
2.7 L diesel (UHZ).
(3) For normal use and engines:
32 000 km
Duration before 1st service
00 months
(2)
Kilometre threshold for forcing of customer mode
250 km
(2)
Memorisation of faults
Authorised
Presence of an electric secondary brake Electrically adjustable rear seats
No Yes Absent
•
1.8 L petrol (6FY),
•
3.0 L petrol (XFV),
•
2.0 L diesel (RHR),
•
2.2 L diesel (4HP, 4HT),
•
2.7 L diesel (UHZ).
(2) (3) (1) (2)
Key: Parameter to be systematically checked after configuring by internet Page 16 / 31
Configuration parameter (A)
Value to be configured
Presence of the welcome function for the driver
No
With manual adjustment of the height and reach of the steering wheel.
Yes
With electrical adjustment of the height and reach of the steering wheel.
Comments
For engines: Engine relay unit (BSM) Origin of the oil pressure information
Number of switches for non-fastening of seatbelts Sensor for detection of presence of a front passenger Detection of nonfastening of the driver's seatbelt
5
(2)
Absent
(2)
Yes
(2)
Detection of nonfastening of the front passenger’s seat belt
Yes
(2)
Presence of a red warning lamp for the Steering Assistance alert Presence of an orange warning lamp for the Steering Assistance alert Tolerance on value set for the cruise control / speed limiter Lane Departure Warning System option
3.0 L petrol (XFV),
•
1.6 L diesel (9HZ),
•
2.0 L diesel (RHR),
•
2.7 L diesel (UHZ).
For engines:
Engine ECU
Presence of a radio RD4
•
No Yes
•
1.8 L petrol (6FY),
•
2.0 L petrol (RFJ),
•
2.2 L diesel (4HP, 4HT).
(1)
No
Mechanical power steering.
Yes
Hydraulic power steering.
Yes
(2)
3 km/h
(2)
Absent
(1) Depending on presence of a button for deactivation of the function.
Present
Key: Parameter to be systematically checked after configuring by internet Page 17 / 31
Configuration parameter (A)
Value to be configured No
Presence of a fuel pump
Comments All diesel engines except: •
On engines: Yes
Presence of a boot relay unit
No
(2)
Type of vehicle
Saloon Estate
(1)
Presence of HeadUp display
No
(2)
Presence of a mobile deflector
No
(2)
Presence of HandsFree Kit Presence of CD changer
2.7 L diesel (UHZ).
No Yes Absent Present
•
Petrol,
•
2.7 L diesel (UHZ).
(1) (1)
Detection of nonfastening of middle rear passenger’s seat belt
Yes
(2)
Detection of nonfastening of rear LH passenger’s seatbelt
Yes
(2)
Detection of nonfastening of rear RH passenger’s seatbelt
Yes
(2)
No
(1) Depending on the presence of a bass box in the boot.
Presence of an audio equaliser amplifier Sound alert for parking assistance emitted by switch module under steering wheel
Yes No
With radio/CD/MP3/RD4 or telematic unit (RT4, RT5, NG4) or radio navigation (RNEG).
Yes
Without audio equipment.
Key: Parameter to be systematically checked after configuring by internet Page 18 / 31
Configuration parameter (A)
Value to be configured
Display of fuel consumption without overconsumption due to regeneration of the particle filter
No
Time of response by the engine ECU to the BSI during operation of cruise control Display of the rear seat belt fastening alert on opening of a rear door or switching on the ignition Retention of braking (by the ESP) for 2 seconds when starting on a gradient Battery charge estimation function Presence of massaging front seats Presence of a Built-in Hydraulic Interface (BHI)
(2)
0.6 s
•
All engines except 1.6 L Diesel (9HZ),
•
1.6L diesel (9HZ) engine and BSI software version ≥ 6.30.
•
1.6L diesel (9HZ) engine and BSI software version = 5.50.
1.2 s
Yes
(2)
No
Handbrake with warning lamp.
Yes
Electric secondary brake.
Present, performed by the Battery (2) charge status control unit No Yes
(1)
No
Metal suspension.
Yes
Hydropneumatic suspension
No
Presence of power steering
Yes
Presence of services module
No Yes
Presence of a navigation system (NG4) Presence of a radio RD4 Presence of HandsFree Kit
Comments
No Yes No Yes No Yes
With mechanical power steering. With hydraulic power steering, (presence of an electro-pump) (1) Configure « yes » if a telematic unit (NG4) with emergency call button is present. (1) (1) (1)
Key: Parameter to be systematically checked after configuring by internet Page 19 / 31
Configuration parameter (A)
Value to be configured
Presence of CD changer
No Yes
(1)
Presence of massaging front seats
No Yes
(1)
Comments
4.4.2 Menu: air conditioning – cabin heating (menu B) Configuration parameter (B) Presence of the pollution sensor Presence of humidity sensor in the cabin
Type of sunlight sensor
Value to be configured No
For Mono-zone Automatic Air Conditioning.
Yes
For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side).
No
(2)
Mono-zone sunlight sensor
Type of air mixing Bi-zone Mono-zone
Type of additional heating
For Mono-zone Automatic Air Conditioning.
For Bi-zone Automatic Air Conditioning (separate Bi-zone sunlight adjustment of the temperature and air distribution on the sensor left-hand side and right-hand side). Mono-zone
Type of air distribution
Comments
For Mono-zone Automatic Air Conditioning. For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). For Mono-zone Automatic Air Conditioning.
Bi-zone
For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side).
Absent
For petrol engines.
Heating elements Autonomous burner
For a diesel engine without additional heating. For a diesel engine with additional heating.
Key: Parameter to be systematically checked after configuring by internet Page 20 / 31
Configuration parameter (B)
Value to be configured Programmable burner 1,19
Comments For a diesel engine with programmable additional heating. For engines: •
3 L petrol (engine plate XFV).
For engines: 1,24 Aircon compressor drive ratio
•
1.8 L petrol (engine plate 6FY),
•
2.0 L petrol (engine plate RFJ).
For engines: • 1.6 L diesel (engine plate 9HZ),
1.28
• 2.0 L diesel (engine plate RHR), • 2.2 L diesel (engine plate 4HP and 4HT).
1.34 Mono-zone Presence and type of blown air sensor Presence of electric sun blind
Bi-zone No
For engines: •
2.7 L diesel (engine plate UHZ).
For Mono-zone Automatic Air Conditioning. For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). (2)
Key: Parameter to be systematically checked after configuring by internet Page 21 / 31
Configuration parameter (B)
Value to be configured
Comments
Temperate (-17°C to +37°C)
For vehicles destined for the following countries, territories or departments: South Africa, Barbados, Belgium, Bermuda, Cyprus, Spain, Metropolitan France, United Kingdom, Greece, Grenada, Guadeloupe, Guyana, Ireland, Italy, Jamaica, Luxembourg, Malta, Martinique, Mauritius, New Caledonia, New Zealand, Netherlands, French Polynesia, Portugal, Reunion, St. Martin, St. Lucia, Seychelles, Tahiti, Trinidad & Tobago.
Cold (-25°C to +37°C)
For vehicles destined for the following countries: Albania, Germany, Austria, Azerbaijan, Bosnia, Bulgaria, Croatia, Denmark, Estonia, Hungary, Iceland, Latvia, Lithuania, Macedonia, Poland, Romania, SerbiaMontenegro, Slovakia, Slovenia, Switzerland, Czech Republic.
Very cold (-30°C to +37°C)
For vehicles destined for the following countries: Armenia, Belarus, Finland, Georgia, Kazakhstan, Kirghizistan, Moldavia, Norway, Uzbekistan, Russia, Sweden, Turkmenistan, Ukraine.
Hot (-17°C to +45°C)
For vehicles destined for the following countries: Algeria, Angola, Antigua & Barbuda, Argentina, Aruba, Australia, Bahamas, Bangladesh, Benin, Bolivia, Botswana, Brazil, Brunei , Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Sierra Leone, Chile, Colombia, Comoros, Congo, South Korea, Costa Rica, Ivory Coast, Cuba, Djibouti, Egypt, El Salvador, Ecuador, Ethiopia, Fiji, Gabon, Gambia, Ghana , Guatemala, Guinea, Haiti, Honduras, Hong Kong, India, Indonesia, Iraq, Iran, Israel, Japan, Jordan, Kenya, Laos, Lebanon, Liberia, Libya, Macao, Madagascar, Malaysia, Malawi, Mali, Morocco, Mauritania, Mayotte, Mexico , Mozambique, Namibia, Nicaragua, Niger, Nigeria, Uganda, Pakistan, Palestine, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Central African Republic, Dominican Republic, Rwanda, Senegal, Singapore, Somalia, Sudan, Sri Lanka, Surinam, Syria, Tajikistan, Taiwan, Tanzania, Chad, Thailand, Togo, Tonga, Tunisia, Turkey, Myanmar, Uruguay, Venezuela, Vietnam, Yemen, Zambia, Zimbabwe.
Very hot (-17°C to +50°C)
For vehicles destined for the following countries: Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar.
Type of climate
Key: Parameter to be systematically checked after configuring by internet Page 22 / 31
Configuration parameter (B)
Value to be configured
Presence of heated seats
No Yes
Type of aircon pressure sensor
Pressure sensor 30 bars
Comments Depending on presence or absence of heated seat controls. (2)
4.4.3 Menu: lighting – signalling – visibility – rear view mirrors (menu C) Configuration parameter (C) Sunlight sensor option
Rain sensor option
Value to be configured Absent Present Absent Present
Comments Configure Present if the vehicle is fitted with a wipers stalk with « auto » position. Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.
Headlamp wash option
Absent Present
(1)
Automatic lighting of instrument panel and multifunction screen depending on external brightness
Absent
(2)
Automatic lighting of hazard warning lamps in the event of impact
Absent
(2)
Absent Present
Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.
Automatic lighting of hazard warning lamps under heavy deceleration
Present
(2)
Presence of front foglamps
No Yes
(1)
Guide-me-home lighting option
Key: Parameter to be systematically checked after configuring by internet Page 23 / 31
Configuration parameter (C)
Value to be configured
Multiplexed folding electric rear view mirrors
No
Rear view mirrors indexed to reverse gear
Yes No Yes
Comments Driver's door control pad with screenprinted button . Driver's door control pad with screenprinted button . Depending on whether the rear view mirrors are equipped with electric folding or not.
Presence of rear screen wiping in reverse gear
Absent Present
Configure Present if a rear wiper is fitted.
Lighting of hazard warning lamps on pressing the emergency call button
Absent
(2)
Single filament halogen bulbs
(1)
Type of headlamps
Discharge bulbs
Type of daytimerunning lamps
Presence of a rain and sunlight sensor with wipers with regulated speed Presence of a lighting stalk with four positions Presence of a stalk with one-touch activation of automatic wipe
No daytimerunning lamps Dedicated daytimerunning lamps
(1)
No Yes
Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.
No Yes
(1)
No Yes
Configure yes if the vehicle is fitted with a wipers stalk with « auto » position.
Key: Parameter to be systematically checked after configuring by internet Page 24 / 31
Configuration parameter (C)
Value to be configured
Activation of automatic lighting of headlamps via the personalisation menu
No
Presence of a third button on the high frequency remote control for switching on the lights
Lighting of daytimerunning lamps by default
Simultaneous lighting of daytime-running lamps and sidelamps
Comments
(2)
No Configure « No » for vehicles fitted with a motorised boot. Yes
No
For all vehicles except those destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
Yes
For all vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
No
For all vehicles except those destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
Yes
For all vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)
Presence of parking lamps
No
(2)
Presence of headlamp height correctors
No
(2) Configure this parameter to « No » even if the vehicle is fitted with headlamp height correctors
Presence of the light pack unit
No Yes
Configure yes if the vehicle is fitted with « light bars » under the fascia.
Type of bend lighting
Static lighting controlled by the BSI Dynamic lighting: directional headlamps
Presence of rear screen wiping in reverse gear
Absent Present
If the vehicle is fitted with halogen bulbs.
If the vehicle is fitted with discharge bulbs.
Configure Present if a rear wiper is fitted.
Key: Parameter to be systematically checked after configuring by internet Page 25 / 31
4.4.4 Menu: locking – doors and tailgate - immobiliser - alarm (menu D) Configuration parameter (D)
Value to be configured
Opening of the boot using the high frequency remote control option
Absent
If standard tailgate.
Present
If motorised boot tailgate.
Deadlocking Type of locking Normal locking Number / type of sun roof Type of child lock Passenger door lock
Inviolability mode Anti-pinch function on windows and sun roof Presence of a multiplexed sun roof Opening of the rear screen using the high frequency remote control option Presence of electronically controlled fuel flap When actioning unlocking by high frequency remote control
With a locking control with Deadlocking (to check carry out a Deadlocking actuator test). With a locking control with normal locking (to check carry out a Deadlocking actuator test).
No sun roof 1 sun roof
(1)
blind Electric Mechanical Absent Present No alarm
Type of alarm
Comments
(1) Left-hand drive vehicle. Right-hand drive vehicle. Without ultra-sonic detectors (on the roof console or on the windscreen aperture pillars)
Standard alarm
With ultra-sonic detectors (on the roof console or on the windscreen aperture pillars)
Alarm for Belgium
For vehicles destined for Belgium with ultra-sonic detectors (on the roof console or on the windscreen aperture pillars).
Active
(2) (3)
Present on all openers
(2)
Absent
(2)
No
(2)
Absent
(2)
Simultaneous unlocking of all of the Vehicle with normal unlocking. doors Unlocking of driver’s door only
Vehicle with deadlocking.
Key: Parameter to be systematically checked after configuring by internet Page 26 / 31
Configuration parameter (D)
Value to be configured
Type of fitting of alarm
Factory fitted alarm
Type of motorised boot tailgate
Presence of specific high frequency receptor (Japan)
Comments (2)
No motorised boot tailgate (1) Multiplexed motorised boot tailgate Absent
(2)
Key: Parameter to be systematically checked after configuring by internet Page 27 / 31
4.4.5 Menu: fuel gauge law – oil gauge law (menu E) Configuration parameter (E) Type of fuel Tank capacity Gauge resistance for empty tank Gauge resistance for full tank Fuel gauge law - alert level Fuel gauge law selection of the vehicle
Oil gauge law – engines
Value to be configured Petrol Diesel
Comments (1)
71 litres
For petrol engines.
72 litres
For diesel engines.
330 ohms
For petrol engines.
332 ohms
For diesel engines.
58 ohms
(2)
7 litres
For diesel engines.
8 litres
For petrol engines.
9 litres
For petrol and alcohol engines.
Petrol vehicles Diesel vehicles Type of engine: XFV (3.0L petrol) Type of engine: 9HZ (1.6L diesel) Type of engine: RHR (2.0L diesel) Type of engine: 4HP, 4HT (2.2L diesel) Type of engine: UHZ (2.7L diesel) Type of engine: 6FY (1.8L petrol) Type of engine: RFJ (2.0L petrol)
(1)
(1)
For engines: Engine relay unit (BSM) Origin of the oil level information
•
3.0 L petrol (XFV),
•
1.6 L diesel (9HZ),
•
2.0 L diesel (RHR),
•
2.7 L diesel (UHZ).
For engines: Engine ECU
•
1.8 L petrol (6FY),
•
2.0 L petrol (RFJ),
•
2.2 L diesel (4HP, 4HT).
Key: Parameter to be systematically checked after configuring by internet Page 28 / 31
4.5 ECUs present Value to be configured
Comments
Steering wheel with fixed central controls
Present
(2)
Airbag
Present
(2)
High frequency receptor
Absent
(2)
Engine relay unit (BSM)
Present
(2)
Rain / sunlight sensor
Absent Present
(1)
Driver's door module
Present
(2)
Built-In Systems Interface
Present
(2)
Alarm
Absent Present
Parking assistance
Absent Present
Instrument panel
Present
Calculator
Absent Audio equipment Present Lane wandering alert
Absent Present
NaviDrive telematic unit
Absent Present Absent
Display Present
Depending on presence of ultra-sonic sensors on the roof console or the windscreen aperture pillar. Depending on the absence or presence of 4 ultra-sonic sensors in the rear bumper. (2) Without radio type RD4. With a telematic unit (RT3, RT4 or NG4). With radio navigation (RNEG). With radio type RD4 (CD or CD/MP3). Depending on presence of a switch for activation of the function. Depending on presence of a NaviDrive telematic receiver (RT3 or RT4), of a telematic unit (NG4) or of radio navigation (RNEG). With telematic unit (RT3, RT4 or NG4) or with radio navigation (RNEG). Without telematic unit (RT3, RT4 or NG4) or with radio navigation (RNEG). Depending on the presence of a trailer relay unit (this equipment is necessary if the vehicle is fitted with a towbar).
Trailer relay unit
Absent Present
Air conditioning
Present
(2)
Driver’s seat memorisation control unit
Absent Present
(1)
Key: Parameter to be systematically checked after configuring by internet Page 29 / 31
Calculator CD changer
Hands-Free Kit
Value to be configured
Comments
Absent Present
(1)
No Yes
Configure « Yes » for vehicles with an RD4 radio (or radio navigation (NG4) without service module) and hands-free kit. To check for the presence of a handsfree kit, press on the « Menu » button of the radio, note the presence of the following icon on the right of the multifunction screen.
Windscreen wipers
Present
(2)
Audio amplifier
Absent Present
(1)
Steering angle sensor
Present
(2)
Engine ECU
Present
(2)
Automatic gearbox / piloted manual gearbox
Absent Present
(1)
ABS / ESP ECU
Present
(2)
Absent
Vehicle with rubber wheel valves.
Present
Vehicles with metallic wheel valves.
Tyre under-inflation detection
Variable damping
Absent Present
Configure « present » for vehicles fitted with hydropneumatic suspension with 3.0L petrol (XFV) or 2.7 L diesel (UHZ) engine.
Suspension
Absent Present
Configure « present » for vehicles fitted with hydropneumatic suspension.
Electric parking brake
Absent Present
(1)
Absent
Vehicles with mechanical power steering.
Present
Vehicles with hydraulic power steering (presence of an electro-pump).
Power steering
Key: Parameter to be systematically checked after configuring by internet Page 30 / 31
Calculator
Value to be configured
Comments
Absent
Vehicles with halogen headlamps.
Present
Vehicles with Xenon headlamps.
Present
(2)
Directional headlamps
Yaw / lateral acceleration sensor Additional heating Motorised boot unit
Absent Present Absent Present
(1) (1)
Seat belt not fastened warning lamp (TNB)
Present
(2)
Battery charge status unit
Present
(2)
4.6 Menu: «VIN code » Enter the vehicle’s VIN code (17 characters).
Key: Parameter to be systematically checked after configuring by internet Page 31 / 31
View more...
Comments
