BS EN 1716
Short Description
Download BS EN 1716...
Description
British Standard I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i L
A single copy of this British Standard is licensed to lbocvzr lbocvzr
25 June 2003
This is an uncontrolled copy. Ensure use of the most current version of this document by searching British Standards Online at bsonline.techindex.co.uk
BRITISH STANDARD
Plastics piping systems Ð Polyethylene (PE) tapping tees Ð Test method for impact resistance of an assembled tapping tee I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i L
The European Standard EN 1716 : 1997 has the status of a British Standard
ICS 23.040.45
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
BS EN 1716 : 1997 BS 2782 : Part 11 : Method 1108T : 1997
BS EN 1716 : 1997
Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/61 Plastics piping systems and components, upon which the following bodies were represented:
I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h gThis British Standard, having ubeen prepared under the o Ldirection of the Sector Board for f Materials and Chemicals, was o published under the authority of y t i the Standards Board and comes s r into effect on e15 June 1997 v i n© BSI 1997 U , r z v c o b l r z v c The following BSI references o b l relate to the work on this : standard: y Committee reference PRI/61 p oDraft for comment 95/121251 DC C dISBN 0 580 27391 1 e s n e c i L
British Gas plc British Plastics Federation British Plumbing Fittings Manufacturers' Association British Valve and Actuator Manufacturers' Association Chartered Institution of Water and Environment Management Department of the Environment (British Board of AgreÂment) Department of the Environment (Building Research Establishment) Department of Transport Electricity Association Health and Safety Executive Institute of Building Control Institute of Materials Institution of Civil Engineers Institution of Gas Engineers National Association of Plumbing, Heating, and Mechanical Services Contractors Pipeline Industries Guild Plastics Land Drainage Manufacturers Association Society of British Gas Industries Society of British Water Industries Water Companies Association Water Services Association of England and Wales The following bodies were also represented in the drafting of this standard, through subcommittees and panels: ERA Technology Ltd. Engineering Equipment and Materials Users' Association RAPRA Technology Ltd.
Amendments issued since publication
Amd. No.
Date
Text affected
BS EN 1716 : 1997
Contents
Committees responsible National foreword Foreword Scope Normative references Principle
2 3 3 3 3
Apparatus Test pieces Conditioning Procedure Test report
3 3 3 3 4
Method 1 2 3 4 5 I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i L
6 7 8
© BSI
1997
Page Inside front cover ii
i
BS EN 1716 : 1997
National foreword This British Standard has been prepared by Technical Committee PRI/61 and is the English language version of EN 1716 : 1997 Plastics piping systems Ð Polyethylene (PE) tapping tee Ð Test method for impact resistance of an assembled tapping tee, published by the European Committee for Standardization (CEN). It is incorporated into BS 2782 Methods of testing plastics: Part 11: Thermoplastics pipes, fittings and valves, as Method 1108T : 1997, for association with related test methods for plastics materials and plastics piping components. This test method has been prepared for reference by other standards under preparation by CEN for specification of plastics piping and ducting systems and components. It has been implemented to enable experience of the method to be gained and for use for other fresh applications. I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i Lii
It is also for use for the revision or amendment of other national standards as practicable, but it should not be presumed to apply to any existing standard or specification which contains or makes reference to a different test method until that standard/specification has been amended or revised to make reference to this method and adjust any requirements as appropriate. Cross-references Publication referred to
Corresponding British Standard
EN 744 : 1995
BS EN 744 : 1996 BS 2782 : Part 11 : Method 1108C : 1996 Plastics piping and ducting systems Ð Thermoplastics pipes Ð Test method for resistance to external blows by the round-the-clock method
NOTE. In the descriptors, the term `shock resistance' should be read as `impact resistance' to avoid confusion with methods for assessing resistance to thermal shock or hydraulic shock.
Warning note. This British Standard, which is identical with EN 1716 : 1997, does not necessarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act 1974. Attention should be paid to any appropriate safety precautions and the method should be operated only by trained personnel. Compliance with a British Standard does not of itself confer immunity from legal obligations .
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover.
© BSI
1997
EN 1716
EUROPEAN STANDARD NORME EUROPEÂ ENNE È ISCHE NORM EUROPA
January 1997
ICS 23.040.45 Descriptors: Plastic tubes, fluid pipelines, polyethylene, junctions, impact tests, determination, shock resistance
English version
Plastics piping systems Ð Polyethylene (PE) tapping tees Ð Test method for impact resistance of an assembled tapping tee I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i L
SysteÁmes de canalisations en plastiques Ð Prises de branchement en polyeÂthyleÁne (PE) Ð MeÂthode d'essai pour la re sistance au choc d'une prise de branchement assemble e
Kunststoff-Rohrleitungssysteme Ð Anbohr-T-Stu È cke aus Polyethylen (PE) Ð Pru È fverfahren fu È r die Widerstandsfa È higkeit gegen Schlagbeanspruchung eines montierten Anbohr-T-Stu È cks
This European Standard was approved by CEN on 1996-09-02. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to Central Secretariat or any CEN member. This European Standard exists in three offical versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CEN European Committee for Standardization Comite EuropeÂen de Normalisation Europa È isches Komitee fu È r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels
© 1997
Copyright reserved to CEN members Ref. No. EN 1716 : 1997 E
Page 2 EN 1716 : 1997
Foreword This European Standard has been prepared by Technical Committee CEN/TC 155, Plastics piping systems and ducting systems, the secretariat of which is held by NNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 1997, and conflicting national standards shall be withdrawn at the latest by July 1997. The material-dependent parameters and/or performance requirements are incorporated in the I SSystem Standard(s) concerned. BThis standard is one of a series of standards on test ) c methods which support System Standards for plastics ( , piping systems and ducting systems. y p According to the CEN/CENELEC Internal Regulations, o Cthe national standards organizations of the following dcountries are bound to implement this European e l l Standard: Austria, Belgium, Denmark, Finland, France, oGermany, Greece, Iceland, Ireland, Italy, Luxembourg, r t nNetherlands, Norway, Portugal, Spain, Sweden, o c Switzerland and the United Kingdom. n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i L
© BSI
1997
Page 3 EN 1716 : 1997
1 Scope
5 Test pieces
This standard specifies a test method for the resistance to impact of polyethylene (PE) tapping tees. This standard is applicable to PE tapping tees intended for the transport of fluids.
5.1 Sampling
2 Normative references
I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i L
This Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 744 : 1995
Plastics piping and ducting systems Ð Thermoplastics pipes Ð Test method for resistance to external blows by the round-the-clock method
3 Principle The cap of the tapping tee is subjected to an impact by means of a weight falling from a constant height, parallel to the axis of the pipe onto which the tapping tee is fused. After two impacts from opposite directions parallel to the main axis of the pipe, the tee is inspected for visible damage and for loss of airtightness. The test is carried out at (0 ± 2) ÊC unless otherwise specified in the referring standard. NOTE. It is assumed that the following test parameters are set by the standard making reference to this standard: a) the sampling requirements (see 5.1); b) the number of test pieces (see 5.3); c) if applicable, the conditioning temperature (see clause 6).
4 Apparatus 4.1 A falling weight testing machine, incorporating the following basic components:
a) main frame, with guide rails or a guiding tube fixed in the vertical position to accommodate a striker and means to release it to fall vertically and freely. When calibrated, the speed of the striker at the moment of hitting the tapping tee shall be not less than 95 % of the theoretical speed; b) striker , conforming to EN 744, but having a special nose consisting of a cylinder with a diameter of (50 ± 2) mm and having a mass of (2500 ± 20) g. 4.2 A rigid support, with a steel mandrel capable of maintaining the test piece in the position shown in figure 1, and means capable of preventing any rotation of the test piece during the test.
© BSI
1997
The sampling requirements shall be as specified in the referring standard. 5.2 Preparation of test pieces The test pieces shall comprise a complete assembly of a pipe, a tapping tee and an end cap. The length of the pipe shall be such that L equals d e (see figure 1).
All joints shall be assembled in accordance with the tapping tee manufacturer's instructions. 5.3 Number of test pieces
The number of test pieces shall be as specified in the referring standard.
6 Conditioning At least 24 h after the tapping tee has been assembled, the test piece shall be conditioned at (0 ± 2) ÊC, unless otherwise specified by the referring standard, for 4 h in air or 2 h in a liquid bath.
7 Procedure 7.1 Condition the test piece in accordance with clause 6 and ensure that the striker will fall through the specified height (see 7.3) before removing the test piece from conditioning. Proceed immediately to 7.2. 7.2 Within 30 s of removal from conditioning, slip the test piece over the mandrel as shown in figure 1 and strike the test piece in accordance with 7.3 or 7.5, as applicable. 7.3 Drop a striker (4.1) on to the cap of the tapping tee from a height of (2000 ± 10) mm along an axis parallel to that of the pipe onto which the tapping tee is assembled. The point of impact, P, on the end cap shall be situated as shown in figure 1. 7.4 Invert the assembly in order to hit the opposite side of the cap. 7.5 After reconditioning under the same conditions, repeat the procedure of 7.2 and 7.3 to strike the cap on the opposite side of the stem of the tapping tee. 7.6 Examine the joint visually, without magnification, and record any crack or rupture, along with its position and its extent. 7.7 Using a liquid as an external leak detector, test the airtightness of the test piece at 25 mbar at an ambient temperature of (23 ± 2) ÊC. Record any evidence of leakage.
Page 4 EN 1716 : 1997
I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 L = d e 0 2 L1 = 0,5 L2 e n A Steel mandrel u J B End cap 5 P Point of impact 2 , h Figure 1. g u o r o b8 Test report h gThe test report shall include the following information: u o a) the reference to this standard and to the referring L standard; f o b) the complete identification of the sample, y t i including the type of material and the nominal s r dimensions of the pipe and of the tapping tees; e v i c) the test temperature; n U d) the mass of the falling weight; , r z e) the drop height; v c f) the number of test pieces tested; o g) any type of failure and/or evidence of leakage; b l r z h) any factors which may have affected the results, v such as any incidents or any operating details not c o specified in this standard; b l i) the date of test. : y p o C d e s n e c i L
© BSI
1997
BS EN 1716 : 1997
List of references
See national foreword.
I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c o b l : y p o C d e s n e c i L
© BSI
1997
I S B ) c ( , y p o C d e l l o r t n o c n U , 3 0 0 2 e n u J 5 2 , h g u o r o b h g u o L f o y t i s r e v i n U , r z v c o b l r z v c BSI o b l 389 Chiswick High Road : London y pW4 4AL o C d e s n e c i L
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
BSI Ð British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions
British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards
Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards
BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means ± electronic, photocopying, recording or otherwise ± without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
View more...
Comments
