BS EN 13877-2:2013
BSI Standards Publication
Concrete pavements Part 2: Functional requirements for concrete pavements
BS EN 13877-2:2013
BRITISH STANDARD
National foreword This British Standard is the UK implementation of EN 13877-2:2013. It supersedes BS EN 13877-2:2004, which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/510/3, Materials for concrete roads. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. © The British Standards Institution 2013. Published by BSI Standards Limited 2013. ISBN 978 0 580 79423 0 ICS 93.080.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2013. Amendments issued since publication Date
Text affected
BS EN 13877-2:2013
EN 13877-2
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
March 2013
ICS 93.080.20
Supersedes EN 13877-2:2004
English Version
Concrete pavements - Part 2: Functional requirements for concrete pavements Chaussées en béton - Partie 2: Exigences fonctionnelles pour les chaussées en béton
Fahrbahnbefestigungen aus Beton - Teil 2: Funktionale Anforderungen an Fahrbahnbefestigungen aus Beton
This European Standard was approved by CEN on 10 February 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN
All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
Ref. No. EN 13877-2:2013: E
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Contents
Page
Foreword ..............................................................................................................................................................3 1
Scope ......................................................................................................................................................4
2
Normative references ............................................................................................................................4
3 3.1 3.2
Terms and definitions, symbols and abbreviated terms ...................................................................5 Terms and definitions ...........................................................................................................................5 Symbols and abbreviated terms ..........................................................................................................6
4 4.1 4.2 4.2.1 4.2.2 4.2.3 4.3 4.3.1 4.3.2 4.3.3 4.4 4.5 4.6 4.7 4.8 4.9
Functional requirements for concrete pavements .............................................................................6 General ....................................................................................................................................................6 Strength of concrete pavements ..........................................................................................................6 General ....................................................................................................................................................6 Core compressive strength ..................................................................................................................7 Core tensile splitting strength ..............................................................................................................8 Thickness of concrete pavements .......................................................................................................9 General ....................................................................................................................................................9 Method 1 (from cores) ........................................................................................................................ 10 Method 2 (by a non-destructive method) ......................................................................................... 10 Density of concrete pavements......................................................................................................... 10 Freeze-thaw resistance ...................................................................................................................... 11 Wear resistance of concrete pavements to studded tyres ............................................................. 11 Bond between two concrete layers................................................................................................... 11 Dowels and tie bars ............................................................................................................................ 12 Resistance against fuel and oil penetration .................................................................................... 12
5
Categories of quality controls for concrete pavements ................................................................. 12
Annex A (informative) Method of evaluating concrete core strength ........................................................ 14 Annex B (normative) Functional requirements for penetration in pavements with high risk of exposure to fuel, oil and other chemical liquids ............................................................................. 15 Bibliography ..................................................................................................................................................... 16
2
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Foreword This document (EN 13877-2:2013) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013 and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13877-2:2004. The following modifications have been made:
The normative references have been reviewed.
The definition of continuously reinforced concrete roadbase (CRCR) has been modified to continuously reinforced concrete base (CRCB).
The units have been updated from N/mm to MPa.
The limitation for cracks in jointed unreinforced concrete pavements has been improved.
Alternative methods to EN 12390 for splitting strength might be used, if defined by relevant national standards or provisions in the place of use. A note has been included after Table 3 to explain it.
Table 3 has been modified to include more splitting strength classes.
In Table 4, a new category of Tolerance, T6, has been included.
Alternative methods to CEN/TS 12390-9 for freeze-thaw resistance might be used, if defined by relevant national standards or provisions in the place of use.
Regarding quality control, allowance has been included for different number of cores, if defined by specifications in the place of use; and the notes after table 7 have been included as normative text.
Reference to EN 197-1 has been added to the Bibliography.
2
This European Standard is one of a series of standards as listed below:
EN 13877-1, Concrete pavements — Part 1: Materials
EN 13877-2, Concrete pavements — Part 2: Functional requirements for concrete pavements
EN 13877-3, Concrete pavements — Part 3: Specifications for dowels to be used in concrete pavements
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3
BS EN 13877-2:2013 EN 13877-2:2013 (E)
1
Scope
This European Standard specifies requirements for concrete pavements cast in situ and compacted by vibration. This European Standard also covers concrete sub-bases as well as concrete wearing courses on bridges. This European Standard covers concrete pavements in motorways, airfields, pedestrian streets, cycle tracks, storage areas and, in general, all traffic-bearing structures.
2
Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 206-1, Concrete — Part 1: Specification, performance, production and conformity EN 12350-1, Testing fresh concrete — Part 1: Sampling EN 12390-1, Testing hardened concrete — Part 1: Shape, dimensions and other requirements for specimens and moulds EN 12390-2, Testing hardened concrete — Part 2: Making and curing specimens for strength tests EN 12390-6, Testing hardened concrete — Part 6: Tensile splitting strength of test specimens EN 12390-7, Testing hardened concrete — Part 7: Density of hardened concrete EN 12390-8, Testing hardened concrete — Part 8: Depth of penetration of water under pressure CEN/TS 12390-9 , Testing hardened concrete — Part 9: Freeze-thaw resistance — Scaling EN 12504-1, Testing concrete in structures — Part 1: Cored specimens — Taking, examining and testing in compression EN 13863-1, Concrete pavements — Part 1: Test method for the determination of the thickness of a concrete pavement by survey method EN 13863-2, Concrete pavements — Part 2: Test method for the determination of the bond between two layers EN 13863-3, Concrete pavements — Part 3: Test methods for the determination of the thickness of a concrete pavement from cores EN 13863-4, Concrete pavements — Part 4: Test methods for the determination of wear resistance of concrete pavements to studded tyres EN 13877-1, Concrete pavements — Part 1: Materials EN 13877-3, Concrete pavements — Part 3: Specifications for dowels to be used in concrete pavements
4
BS EN 13877-2:2013 EN 13877-2:2013 (E)
3
Terms and definitions, symbols and abbreviated terms
For the purposes of this document, the following terms and definitions, symbols and abbreviated terms apply.
3.1
Terms and definitions
3.1.1 maturity measure of strength gain of concrete as a function of the product of temperature and length of a specific time interval 3.1.2 characteristic strength value of strength below which 5 % of the population of all possible strength determinations of the volume of concrete under consideration are expected to fall 3.1.3 functional requirements properties of a concrete pavement that ensure compliance with the design requirements 3.1.4 jointed unreinforced concrete pavement concrete pavement with transverse joints at intervals generally from 3,0 m to 7,5 m Note 1 to entry: The slabs are not reinforced and the load transfer across transverse joints is provided either by round steel dowels (dowelled) or by aggregate interlock only (undowelled).
3.1.5 jointed reinforced concrete pavement concrete pavement with transverse joints at intervals generally from 8 m to 25 m Note 1 to entry: These joints may be either contraction or expansion joints. The pavement slabs contain steel reinforcement in both the longitudinal and transverse directions. The longitudinal reinforcement does not cross the transverse joints, which are usually dowelled.
3.1.6 continuously reinforced concrete pavement (CRCP) concrete pavement with continuous longitudinal steel reinforcement and no intermediate transverse expansion or contraction joints 3.1.7 continuously reinforced concrete base (CRCB) layer of continuously reinforced concrete, with a percentage of longitudinal crack control steel lower (about two thirds) than that generally used in continuously reinforced concrete pavements, and intended to be surfaced with a relatively thick (about 10 cm) overlay of bituminous mixture 3.1.8 contraction joint formed, sawn or tooled grooves in a concrete pavement to create a weakened plane and to control the location of cracking resulting from the dimensional change of the structure Note 1 to entry:
It could be transverse or longitudinal.
3.1.9 expansion joint separation between pavement slabs filled with a compressible material
5
BS EN 13877-2:2013 EN 13877-2:2013 (E)
3.2
Symbols and abbreviated terms
CC8 to CC100
compressive strength classes for concrete
SC1,3 to SC6,0
tensile splitting classes for concrete
fck,core
characteristic compressive strength of concrete determined from cores
ftk,core
characteristic tensile splitting strength of concrete determined from cores
T1 to T6
categories for thickness tolerance
DMAX
the nominal maximum size of the coarse aggregate, expressed in millimetres (mm)
FT0 to FT2
categories for freeze/thaw resistance
m28 and m56
mass loss after 28 days and 56 days, expressed in kilograms per square metre (kg/m2)
WR0 to WR4
categories for wear resistance of concrete pavement to studded tyres
RWI
relative wear index value
Xm
mean value of bond strength between two concrete layers, expressed in megapascals (MPa)
xi
individual result for compressive or tensile splitting strength determined from cores
x4m
mean value of 4 consecutive results of compressive or tensile splitting strength determined from cores
fv
the required bond strength, expressed in megapascals (MPa)
sn
the standard deviation; a value of 0,4 shall be used if sn < 0,4
4
Functional requirements for concrete pavements
4.1
General
The appropriate functional requirements shall be specified. Jointed unreinforced concrete pavements shall not have large cracks impairing their bearing capacity.
4.2
Strength of concrete pavements
4.2.1
General
The strength of a concrete pavement shall be determined from cores, which have been drilled from the full depth of the slab. The concrete strength shall be determined in accordance with one of the methods given in 4.2.2 and 4.2.3. The strength class shall be selected from a characteristic value given in 4.2.2 or 4.2.3. The characteristic strength shall be evaluated in accordance with EN 206-1. NOTE 1
6
Classes refer to the 28 day equivalent maturity strength.
BS EN 13877-2:2013 EN 13877-2:2013 (E)
The criteria given in Annex A may be used for the evaluation of core strengths throughout the whole of the constructed pavement. Intermediate strength classes may be selected among those given in 4.2.2 and 4.2.3. NOTE 2
4.2.2
The different classes given in 4.2.2 and 4.2.3 are not directly correlated.
Core compressive strength
The core compressive strength shall be determined in accordance with EN 12504-1. The number of cores to be tested shall be as specified in Clause 5. Where it is not possible to test cores with a length/diameter ratio equal to 1, corrections shall be made in accordance with specifications in the place of use or as recommended in Table 1. Additionally, corrections due to the presence of steel reinforcement may be made in accordance with specifications in the place of use. Table 1 — Correction factors for compressive strength of cores with different length/diameter ratios Length/diameter ratio
Correction factor
1,00
1,00
1,25
1,07
1,50
1,12
1,75
1,16
2,00
1,18
The strength class shall be selected from a characteristic value given in Table 2.
7
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Table 2 — Compressive strength classes of cores Strength class
Characteristic core strength (fck,core) MPa
CC8
8
CC12
12
CC16
16
CC20
20
CC25
25
CC30
30
CC35
35
CC40
40
CC45
45
CC50
50
CC55
55
CC60
60
CC70
70
CC80
80
CC90
90
CC100
100
For functional reasons it is recommended that the minimum strength class for pavement concrete should not be less than CC20. If cores are not tested at a maturity of 28 days at 20 °C the result should be modified either by using maturity concepts to give estimated strength at 28 days at 20 °C or in accordance with specifications in the place of use. Cores can be taken after 3 days to 7 days and should be cured in accordance with EN 12504-1. For CRCP and CRCB an upper limit of strength may be specified. 4.2.3
Core tensile splitting strength
The core splitting strength shall be determined in accordance with EN 12390-6. Other test methods may be specified by relevant national standards or provisions in the place of use. The number of cores to be tested shall be as specified in Clause 5. The strength class shall be selected from a characteristic value given in Table 3.
8
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Table 3 — Tensile splitting strength classes of cores Strength Class
Characteristic core strength (ftk,core) MPa
SC1,3
1,3
SC1,7
1,7
SC2,0
2,0
SC2,4
2,4
SC2,7
2,7
SC3,3
3,3
SC3,7
3,7
SC4,0
4,0
SC4,3
4,3
SC4,6
4,6
SC4,8
4,8
SC5,0
5,0
SC5,5
5,5
SC6,0
6,0
For functional reasons it is recommended that the minimum strength class for pavement concrete should not be less than SC1,7. If cores are not tested at a maturity of 28 days at 20 °C the result should be modified using maturity concepts to give estimated strength at 28 days at 20 °C or in accordance with specifications in the place of use. Cores can be taken after 3 days to 7 days and should be cured in accordance with EN 12504-2. For CRCP and CRCB an upper limit of strength may be specified. Table 3 can be substituted for a national table, if a test method other than EN 12390-6 is used to determine the tensile splitting strength.
4.3 4.3.1
Thickness of concrete pavements General
The thickness of concrete pavement shall be determined by using one of the methods given in 4.3.2 and 4.3.3. The method for determining the thickness of concrete pavement shall be specified. The pavement thickness shall be the arithmetic mean of the individual core measurements and shall not be less than the design thickness. Any individual core measurements shall not be less than the design thickness minus the T-category value given in Table 4.
9
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Table 4 — Categories for thickness tolerance Category of tolerance
Maximum reduction of pavement thickness on an individual core mm
T1
< 25
T2
< 20
T3
< 15
T4
< 10
T5
1,5 kg/m2
No requirement
No requirement
FT2
< 0,5 kg/m2 on average
< 1,0 kg/m2 on average with no individual result > 1,5 kg/m2
≤2
4.6
Wear resistance of concrete pavements to studded tyres
Wear resistance of concrete pavements to studded tyres is classified according to its Relative Wear Index (RWI) value determined in accordance with EN 13863-4. Categories shall be selected from Table 6. Table 6 — Categories for wear resistance of concrete pavements to studded tyres
4.7
Category
Relative Wear Index
WR0
No requirement
WR1
> 135
WR2
> 110 and ≤ 135
WR3
> 85 and ≤ 110
WR4
≤ 85
Bond between two concrete layers
If the bond between two concrete layers is to be tested, testing shall be carried out in accordance with EN 13863-2. The number of cores to be tested shall be as specified in Clause 5 and should not be less than 9.
11
BS EN 13877-2:2013 EN 13877-2:2013 (E)
The mean value for the bond strength between two concrete layers shall satisfy the following relationship. X m ≥ f v + 1,4 sn
(1)
where Xm
is the mean value of bond strength between two concrete layers, expressed in megapascals (MPa);
fv
is the required bond strength, expressed in megapascals (MPa);
sn
is the standard deviation; a value of 0,4 shall be used if sn < 0,4.
NOTE
4.8
The bond strength for normal concrete is typically fv = 1,0 MPa.
Dowels and tie bars
Where required, dowels and tie bars shall conform to EN 13877-1 and EN 13877-3. The distance between tie bars shall not exceed 2 m and the spacing between dowels shall not be greater than 12 times their diameter. These values may be doubled for lightly trafficked lanes (e.g. overtaking lanes), for emergency lanes, and between wheel tracks for heavily trafficked lanes. The outer dowels shall not be less than 250 mm from an edge. The tolerances for dowel and tie bar positions shall be in accordance with specifications in the place of use.
4.9
Resistance against fuel and oil penetration
When required, the test shall be in accordance with the method given in Annex B.
5
Categories of quality controls for concrete pavements
Quality control for compliance testing shall be determined in accordance with Table 7. Other numbers of cores different from those included in Table 7 are possible, depending on the specifications in the place of use. Different categories can be selected for each requirement.
12
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Table 7 — Number of cores for different categories of quality control of constructed pavements Requirement
Category a 0
1
2
Strength of concrete (see 4.2)
N.R.
3/10 000 m²
1/1 000 m²
Thickness of concrete pavement (see 4.3)
N.R.
3/10 000 m²
1/1 000 m² b
Density of concrete (see 4.4) c
N.R.
3/10 000 m²
1/1 000 m²
Freeze/thaw resistance (see 4.5)
N.R.
3/10 000 m²
1/1 000 m²
Wear resistance of concrete pavement to studded tyres (see 4.6)
N.R.
N.R.
3/100 000 m²
Bond between two concrete layers (see 4.7)
N.R.
3/10 000 m²
1/1 000 m²
d
a
N.R. = No requirement for functional testing.
b
For paving areas up to 3 000 m² a minimum of 3 cores shall be taken. For each further area of 1 000 m 2 an additional core shall be taken.
c
A minimum of 3 cores shall be taken.
d
A minimum of 9 cores shall be taken in order to obtain a statistically significant result.
Where strength, thickness and/or density are determined, they may be measured from the same core. To prevent undue damage to the pavement surface, cores should not be extracted at points where high stresses can occur, such as corners of slabs, and not within 0,5 m of any joint. The ideal locations for taking cores are between the quarter points along a slab in a jointed pavement, and between two consecutive transverse cracks in a CRCP and a CRCB. When taking cores to check for compliance with the design, the positions for drilling the cores should be agreed in advance by the relevant parties.
13
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Annex A (informative) Method of evaluating concrete core strength This method is based on overlapping groups of four consecutive results on cores taken from the constructed pavement in accordance with EN 12504-1, and following the criteria given in 4.2. Concrete shall be accepted if both the criteria in Table A.1 are satisfied for four results derived from strength tests on cores taken from the constructed pavement. Table A.1 — Conformity criteria for evaluation of core strengths Method of assessing strength Compressive test Tensile splitting test
Criterion 1
Criterion 2
Mean of any 4 consecutive results x4m
Any individual result xI
MPa
MPa
≥ fck, core + 4
≥ fck, core − 4
≥ ftk, core + 0,5
≥ ftk, core − 0,5
NOTE The use of overlapping groups allows a more frequent assessment of compliance to be made than with nonoverlapping groups. The use of overlapping groups in place of non-overlapping groups reduces the risk of accepting material of unacceptable quality. The use of groups of four samples, whilst maintaining the acceptance criteria given in EN 206-1 that is appropriate for groups of three specimens, provides a compensation for this change of risk.
14
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Annex B (normative) Functional requirements for penetration in pavements with high risk of exposure to fuel, oil and other chemical liquids Fuel, oil and chemical liquid penetration shall be determined from cores 150 mm in diameter, drilled from either the full depth of the slab or with a length of at least 80 mm. NOTE 1
This requirement is only relevant to concrete pavements with a high risk of fuel or oil spillage.
The cores shall be tested in accordance with EN 12390-8 using water as the penetrating agent. The test shall be carried out when the concrete has reached a maturity between 13 440 °Ch and 16 800 °Ch. The maturity at the time of drilling shall be calculated from data provided by an official meteorological institute. After drilling the cores they shall be stored in accordance with EN 12504-1. At least one day before testing, the exposed side of the core shall be coated with an epoxy, leaving a central circle of 75 mm in diameter. NOTE 2 Comparative tests have shown that there is no significant difference between using fuel or water as the penetrating agent.
The allowable vertical depth of penetration shall be not more than 30 mm. The number of cores to be tested shall be as specified in Clause 5. Table B.1 — Categories for testing of fuel and oil penetration a Requirement Fuel and oil penetration a
Category 0 No requirement
1 3/10 000 m2
2 1/1 000 m2
Water, fuel and oil tightness of joints shall be developed in the future.
15
BS EN 13877-2:2013 EN 13877-2:2013 (E)
Bibliography [1]
16
EN 197-1, Cement — Part 1: Composition, specifications and conformity criteria for common cements
This page deliberately left blank
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
British Standards Institution (BSI) BSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.
About us
Revisions
We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.
Our British Standards and other publications are updated by amendment or revision.
The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.
Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at bsigroup.com/standards or contacting our Customer Services team or Knowledge Centre.
Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at bsigroup.com/shop, where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.
Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to bsigroup.com/subscriptions. With British Standards Online (BSOL) you’ll have instant access to over 55,000 British and adopted European and international standards from your desktop. It’s available 24/7 and is refreshed daily so you’ll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when they’re revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit bsigroup.com/shop. With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as they’re available, you can be sure your documentation is current. For further information, email
[email protected].
BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK
We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.
Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.
Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders):
[email protected] Email (enquiries):
[email protected] Subscriptions Tel: +44 845 086 9001 Email:
[email protected] Knowledge Centre Tel: +44 20 8996 7004 Email:
[email protected] Copyright & Licensing Tel: +44 20 8996 7070 Email:
[email protected]
