BS en 10277 4 2008 Bright Steel Products —Case Hardening Steel— Part 4 General
Short Description
Download BS en 10277 4 2008 Bright Steel Products —Case Hardening Steel— Part 4 General...
Description
BRITISH STANDARD
I S B ) c ( , y p o C d e l l o r t n o c n U , 6 0 0 2 0 0 : 0 0 + T M G 9 1 : 6 0 : 4 0 6 2 t c O u h T , a n , n u d l e i f f e h s n u d l e i f f e h s : y p o C d e s n e c i L
Bright steel products Ð Technical delivery conditions Ð Part 4: Case-hardening steels
The European Standard EN 10277-4:1999 has the status of a British Standard
ICS 77.140.60
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
BS EN 10277-4:1999
BS EN 10277-4:1999
National foreword I S B ) c ( , y p o C d e l l o r t n o c n U , 6 0 0 2 0 0 : 0 0 + T M G 9 1 : 6 0 : 4 0 6 2 t c O u h T , a n , n u d l e i f f e h s n u d l e i f f e h s : y p This British Standard, having o been prepared under the C direction of the Engineering d Sector Committee, was published e s under the authority of the n Standards Committee and comes e into effect on 15 December December 1999 c i L © BSI
12-1999
ISBN 0 580 32836 8
This British Standard is the English language version of EN 10277-4:1999. This part of BS EN 10277 together with BS EN 10278 and BS EN 10277 parts 1, 2, 3 and 5 supersedes BS 970-3:1991 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/31, Wrought steels, which has the responsibility to: Ð aid enquirers enquirers to understa understand nd the text; text; Ð present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; Ð monitor related international and European developments and promulgate them in the UK. A list of organiza organizations tions represen represented ted on this committee committee can be obtained obtained on request request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled ªInternational Standards Correspondence Indexº, or by using the ªFindº facility of the BSI Standards Electronic Catalogue. A British Standard Standard does not purport purport to include include all the necessary necessary provisions provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.
Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages pages 2 to 7 and a back cover. cover. The BSI copyright notice displayed in this document indicates when the document was last issued.
Amendments Amendmen ts issued since publication Amd. Amd. No.
Date
Comment Commentss
EN 10277-4 10277-4
EUROPEAN STANDARD Â ENNE NORME EUROPE È ISCHE NORM EUROPA I S B ) c ( , y p o C d e l l o r t n o c n U , 6 0 0 2 0 0 : 0 0 + T M G 9 1 : 6 0 : 4 0 6 2 t c O u h T , a n , n u d l e i f f e h s n u d l e i f f e h s : y p o C d e s n e c i L
July 1999
ICS 77.140.20; 77.140.60
English version
Brig Bright ht stee steell prod produc ucts ts Ð Techn echnic ical al deli delive very ry condi conditi tion onss Ð Part Part 4: Case-h Case-hard ardeni ening ng steels steels
Produits en acier transforme s aÁ froid Ð Conditions techniques de livraison Ð Partie 4: Aciers pour ce mentation  mentation
Blankstahlerzeugnisse Ð Technische Lieferbedingungen Ð Teil 4: Einsatzsta hle È hle
This European Standard was approved by CEN on 11 June 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which which stipul stipulate ate the condit condition ionss for giving giving this this Europe European an Standa Standard rd the status status of a nation national al standa standard rd withou withoutt any alter alterati ation. on. Up-toUp-to-dat date e lists lists and biblio bibliogr graph aphica icall references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version version in any other other language language made by translat translation ion under the responsib responsibility ility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN CEN memb member erss are are the the nati nation onal al stan standa dard rdss bodi bodies es of Aust Austri ria, a, Belg Belgiu ium, m, Czec Czech h Republ Republic, ic, Denma Denmark, rk, Finla Finland, nd, Franc France, e, Germa Germany ny,, Greec Greece, e, Icelan Iceland, d, Irela Ireland, nd, Italy Italy,, Luxem Luxembou bourg, rg, Nether Netherlan lands, ds, Norway Norway,, Portug Portugal, al, Spain, Spain, Sweden Sweden,, Switze Switzerla rland nd and United Kingdom.
CEN European Committee for Standardization Comite Europe en de Normalisation Europa È isches È isches Komitee fu È r È r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels © 1999
CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10277-4:1999 E
Page 2 EN 10277-4:1999
I S Foreword B ) c This European Standard has been prepared by ( , y Technical Committee ECISS/TC 23, Steels for heat p treatment, alloy steels and free-cutting steels Ð o C Qualities and dimensions, the Secretariat of which is d held by DIN. e l l This European Standard shall be given the status of a o r t national standard, either by publication of an identical n text or by endorsement, at the latest by January 2000, o c and conflicting national standards shall be withdrawn n U at the latest by January 2000. , 6 This European Standard has been prepared under a 0 mandate given to CEN by the European Commission 0 2 and the European Free Trade Association. This 0 European Standard is considered to be a supporting 0 : standard to those applications and product standards 0 0 which in themselves support an essential safety + requirement of a New Approach Directive and which T Mmake reference to this European Standard. G This European Standard EN 10277, Bright steel 9 products products Ð Technical echnical delivery conditions, conditions, is 1 : subdivided as follows: 6 0 : Ð Part 1: General General; 4 0 Ð Part Part 2: Stee Steels ls for general general engineeri engineering ng purpose purposess; 6 Part 3: Free-cu Free-cuttin tting g stee steels ls; 2 Ð Part t Case-ha e-harden rdening ing stee steels ls; c Ð Part 4: Cas O Ð Part Part 5: Stee Steels ls for quench quenching ing and tem temperi pering. ng. u h Accordin According g to the CEN/CEN CEN/CENELEC ELEC Internal Regulatio Regulations, ns, T , the national standards organizations of the following a countries are bound to implement this European n , Standard: Austria, Belgium, Czech Republic, Denmark, n Finland, France, Germany, Greece, Iceland, Ireland, u d l Italy, Luxembourg, Netherlands, Norway, Portugal, e Spain, Sweden, Switzerland and the United Kingdom. i f f e h s n u d l e i f f e h s : y p o C d e s n e c i L
Contents Page Foreword
2
1
Scope
3
2
Normative references
3
3
Definitions
3
4
Classification and designation
3
4.1
Classification
3
4.2
Designation
3
5
Info Inform rmat atio ion n to be supp suppli lied ed by the the purchase purchaserr
3
6
Manufacturing process
3
7
Requirements
3
7.1
Chemical composition
3
7.2
Mechanical properties
3
7.3
Hardenability
3
7.4
Grain size
3
7.5
Non-metallic inclusions
3
7.6 7.6
Supp Supple lem menta entarry or speci pecial al requi quiremen ementts
3
8
Inspection and testing
3
9
Marking
3
© BSI
12-1999
Page 3 EN 10277-4:1999
I S B ) c ( , y p o C d e l l o r t n o c n U , 6 0 0 2 0 0 : 0 0 + T M G 9 1 : 6 0 : 4 0 6 2 t c O u h T , a n , n u d l e i f f e h s n u d l e i f f e h s : y p o C d e s n e c i L
1 Scope
6 Manufacturing process
10277 applies applies to bright steel bars 1.1 1.1 This part of EN 10277 in the drawn, turned or ground condition, in straight lengths of case-hardening steels.
See EN 10277-1.
1.2 1.2 This EN 10277-4 is complemented by EN 10277-1.
7.1 Chemical composition
2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publicatio publications ns apply apply to this European European Standard Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.
7 Requirements 7.1.1 Cast analysis The chemical composition of the steel according to the cast analysis shall be as specified in Table 1. 7.1.2 Product analysis The permissible deviations from the chemical composition as specified in Table 1 for cast analysis and the product analysis of the steel shall be as specified in Table 2. 7.2 Mechanical properties The mechanical properties of the steels shall be as specified in Table 3 and Table 4.
EN 10084:1998, 10084:1998, Case-hardening steels Ð Technical delivery delivery conditions conditions.
7.3 Hardenability
EN 10277-1, Bright steel products Ð Technical delivery conditions Ð Part 1: General .
Where steels are ordered with hardenability requirements, the requirements of EN 10084 shall apply.
EURONORM 1031), Microscopic determination of the ferriti fer riticc or austeni austenitic tic grain grain size size of stee steels ls.
7.4 Grain size
3 Definitions For the purpose of this standard, the following definition applies in addition to the definitions in EN 10277-1.
Unless otherwise agreed, the steel when tested in accordance with one of the methods described in EURONORM 103 shall show an austenitic grain size of 5 to 8. The grain structure shall be considered satisfactory if 70 % of the area is within the specified size limits. For verification see EN 10277-1, B.2 10277-1, B.2..
3.1 3.1 case-hardening steels
7.5 Non-metallic inclusions
steels with a relatively low carbon content, which are intended for carburizing or carbonitriding and subsequent hardening. Such steels, after treatment, are characterized by a high hardness surface layer and a tough core
The steels shall have a degree of cleanness corresponding to the special steel quality.
4 Classification and designation
For details of requirements and verification see A.1 see A.1 and annex D of EN 10084:1998. 7.6 Supplementary or special requirements See annex B of EN 10277-1.
4.1 Classification
8 Inspection and testing
Steel grades C10R, C15R and C16R are non-alloy special steels. All other steel grades covered by this European Standard are alloy special steels.
See EN 10277-1.
4.2 Designation See EN 10277-1.
9 Marking See EN 10277-1.
5 Information to be supplied by the purchaser See EN 10277-1.
1)
It may be agreed at the time of ordering, until this EURONORM has been adopted as a European Standard, that either this EURONORM or a corresponding national standard should be applied.
© BSI
12-1999
Page 4 EN 10277-4:1999
I e o ) S l t 4 b B a B 8 0 n 0 5 ) o 0 0 c s d 0 0 ( a , , e n 0 0 , r a y l l s 0 0 e p A t 0 0 i 5 1 . , 7 , 3 o r , t , 5 1 e a 0 1 C e p i o o h o o o N t t t t e r d p 0 0 0 0 h l e t l 0 8 4 2 a l , , , , g i c 0 3 0 1 i o n n r t a h s h 5 5 i n c 2 2 n , , f i e o 0 0 c m o , o t o f o y n t M t e U l 5 5 s i i o b 1 , , 1 , r p a 0 0 6 n u e ) 0 p d 3 , 0 0 0 0 0 r 0 ) ) 0 0 e a 2 1 , , 3 , 7 , 0 , 9 , 1 h h 2 s ) , 1 , t 1 0 1 1 0 1 i 1 1 r e r 0 s s s C o t o t o t o t o t o t h o t o f y t a 0 l : t n 0 0 0 0 0 5 0 a m a c 0 n 8 6 8 0 6 8 3 e , , , , , , , h f y 0 a b t f 0 0 0 1 0 0 0 a r + e h % T t h s , c t i 0 0 0 o h a n 0 0 0 0 0 M c 4 4 4 , 4 4 4 4 4 o w 0 0 i 0 , 0 , , 0 e G ( t , 0 , 0 , 0 , , r s s i 0 0 0 t 0 0 0 0 0 a n s S n o 9 o h o o o e o t o t o t o 5 t t 5 t t o c t 1 i p r m 3 3 : t u l 0 0 0 0 0 0 0 0 m 0 0 i 6 s o , , p e 2 2 2 2 2 2 2 2 e 0 0 c 0 0 0 0 0 0 0 0 0 e , 0 , 0 , 0 , # 0 , 0 , # 0 , 0 , h h : o l 0 c t a 4 p c f u s 0 m i o . t f m x o 5 5 5 5 5 5 5 5 5 5 6 o n , c e 3 3 3 3 3 3 3 3 3 3 e 2 l h P a e 0 0 0 0 0 0 0 0 0 0 m , , , , , , , , , , m r C t a u e 0 0 0 0 0 0 0 0 0 0 t e c i c c r a g O m a f u 0 0 0 5 0 0 0 0 0 0 n e a e 7 4 0 9 u 6 6 9 3 3 9 , , , , h , , , , , , h t 1 1 0 0 h c 0 0 0 1 1 0 n t m T o o o o u i o o o o o o M t t t t t t t t t t h o n , d 0 0 0 0 0 0 0 0 5 0 t a n i d e 3 3 6 0 0 1 7 4 6 6 s , , , , , , , , , , n a w u 0 0 0 1 1 1 0 0 0 0 l s , e l e a n d e i t r . u a s e x i a d e t r a 0 0 0 0 0 0 0 0 0 S 0 l g h 4 4 4 4 4 4 4 4 4 m 4 t m , , , , , , , , , , e i l 0 0 0 0 0 0 0 0 0 0 t o r f e f e h e d t e t e o h S d r 0 2 9 3 3 8 8 9 9 d 0 s o 2 1 2 2 1 , 0 , 0 , 0 , 2 , 1 , 1 , 1 , 1 , 0 , a p y a n Ð C 0 0 0 0 0 0 l l r u 1 o o o o a o t o t o t o t o t t t t t o n c t d l e o s i 7 2 2 4 4 7 3 4 4 7 l t m e 0 1 1 1 1 1 1 1 1 1 i n r , 0 , 0 , 0 , 0 , 0 , 0 , 0 , 0 , 0 , e o b f 0 f a t f n n e T i o 8 8 8 8 h e 8 8 8 8 8 8 i o 9 9 9 9 b t 9 9 9 9 9 i 9 s e t 9 9 9 9 d t 9 9 9 9 9 9 d g : d 1 a n : 1 : 1 : 1 : 1 : 1 : 1 : 1 : 1 : 1 : o y n a r 4 4 4 4 4 4 4 4 4 4 i l g d e p 8 8 8 8 l 8 8 8 8 8 8 h l r a t 0 0 0 0 0 0 0 0 0 0 o e o h 0 0 0 0 0 s t e c C 1 0 1 0 1 0 1 0 1 1 1 1 1 0 1 e n t c e l S a v d N N N N N N N N N N b e a r E E E E E E E E E E t e p s s i o r n h t t l e 7 0 8 9 0 e 9 5 2 6 9 n e b n e 0 4 0 5 3 6 4 1 2 6 c i e i t m 2 1 2 1 1 k 1 7 7 5 5 d a S u 1 1 1 7 7 L 7 e t . 5 . 5 . 6 . 6 . t n n . . . . . o i t a n e g i m s a e n D l e e t S
1 1 1 1 1
5 5 S r B r C C n n R R R 0 5 6 M 1 1 1 6 M C C C 1 6 1
s d e n s o i a t e d a i n r v u c n e o i r d e a e s t o b e y h p a t u m ; r t s u s n f l e e c t u n s o r c o d p n e g s a n s i r e u n u a r t o g c h n a a p s f u o n m h e p a h m t r e o h f f o t t t i p n e o m c l g i x e i n r , d e d n p p e e t u t p e i e m h d t r , , e s p t s n e e a e r t c . a n s e o s i n i c h s o r t y z l u I n d a f l . n e u a n s t s e t e r s d u r e q a a c h e h g r i . h e 2 e h t s e r n o a l r b o c o d f a ) e e b i s T P l h t p t i t o f m . % p o u i l c 5 s s 3 c e a 0 , e s e h s b t n o e t y m u b a h g l o u a r v P m o f , t s e % ) t e n t n h o h 5 t 1 i , e t s m e 0 a t e i . a v s g v o . r e r e a c e t p d r ( t e d m i m h h a u o g t e i i l l t o c s l f l t , l o a u ) c a 4 . n g b n 8 y i i o . 0 t i t 0 l i e , i 1 d n d n b o a N a d i n t E % a e a e 1 e d h m 0 r e , t s 0 a f r ( o h ± o f y f t t e n l d o i l o u i b i e s b x s e o a a r r n a e c a d r e f s n c d o r n a e a a e i h s t y d r i o i n a l f i f l o c b t u e o e h a s n n d d i a t e d h n l i e c l m a o d e d r d r t m a e e n a d c e o s x e c s t v e a n 1 1 1 1 1 o b e o g c e t r n u i s m o q l i 2 4 n p d h e t l a m r , u t i i l 2 6 o u r e h c s . q n S n h n i y e v 5 4 3 S i s i ( o o s t e t t n i s r S l w S . i n i r S o i e w r 1 r M r M r e o l s % n t b r C C o % 5 r m a e h u a e C i C i C e n i i c h , t e 0 1 i , o l l l l c 0 M N N N N E r W a S 0 B e p 1 0 p 2 h , y 4 s ) 1 p a ) 3 0 b ) 2 6 1 5 1 0 2 7 1 )
© BSI
12-1999
Page 5 EN 10277-4:1999
I S B ) c ( , y p o C d e l l o r t n o c n U , 6 0 0 2 0 0 : 0 0 + T M G 9 1 : 6 0 : 4 0 6 2 t c O u h T , a n , n u d l e i f f e h s n u d l e i f f e h s : y p o C d e s n e c i L
Table 2 Ð Permissible deviations between the product analysis and the limiting values given in Table 1 for the cast analysis Element
Permissibl e ma xi m um content in the cast analysis
Permissible deviation1)
% by mass
% by mass
0,23
±0,02
0,40
+0,03
1,00
±0,04
C
#
Si
#
Mn
#
>1,00 P
#
S
#
Cr
#
Mo
#
Ni
#
±0,05
0,035
+0,005
0,040
+0,0052)
1,30
±0,05
0,25
±0,03
2,00
±0,05
>2,00 B
1,40
#
3,50
#
0,005 0
#
±0,07 ±0,000 5
1) ±
means that in one cast the deviation may occur over the upper value or under the lower value of the specified range in Table 1, but not both at the same time.
2)
For steels with a specified sulfur range (0,020 % to 0,040 % according to cast analysis), the permissible deviation is ± 0,005 %.
© BSI
12-1999
Page 6 EN 10277-4:1999
I n ) S w ) 4 s a . B C s ) 3 r + e B x d ) n H a A d m c + d ( l A + r a o ( , c H 5 6 8 1 2 8 7 0 2 6 8 8 2 4 4 y + 2 1 0 9 7 3 3 1 9 7 4 3 2 0 8 p 2 2 2 1 1 2 2 2 1 1 2 2 2 2 1 o C d e ) d s n s H e e r . l S u l x n t + d B a o H r + r t a m ) A 3 + n H A ( 1 1 1 3 3 3 6 6 6 o + 3 3 3 4 4 4 5 5 5 c Ð Ð Ð Ð Ð Ð 1 1 1 1 1 1 1 1 1 n U . , n 5 i A % 6 m 0 8 9 0 1 2 1 2 1 7 8 9 1 1 2 1 7 8 9 1 1 2 1 0 2 ) 1 s 0 e ) i 0 t 2 : C . 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ) 2 m n 6 3 0 4 8 0 8 3 7 0 2 0 5 9 2 0 s r + e ( i m l p m 7 7 7 6 5 8 7 7 6 6 8 8 7 6 6 0 e o R / m o t o t o t o t o t o t o t o t o t o t o t o t o t o t o + e r n N t p w T t a l 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 s a r 6 M y c 4 3 4 0 5 8 4 3 5 0 5 5 4 5 3 2 3 0 4 8 3 4 3 2 4 0 4 6 3 i d d G l o n l a o 9 l h C a c 1 e : n 2 ) 6 o M 2 m 2 , 0 n 0 m : p / R N 4 f 0 o 0 0 0 0 0 0 0 0 0 5 0 0 0 0 5 s 5 0 8 4 0 6 6 e 5 0 8 8 4 1 0 6 3 . 3 3 2 2 1 3 3 2 2 2 4 3 3 2 2 r i 2 t . e % d t r r 0 c e o 1 d ± O p o n y ) 2 a r 0 0 0 0 0 0 0 0 0 b u p H m 5 5 5 0 0 0 2 2 2 y m S h l r ) 5 5 5 6 6 6 6 6 6 i m R / + m ( T a u R o t o t o o t o t o o t o t o q N t t t ( , i c d n h e e a n 0 0 0 0 0 0 0 0 0 t n f 1 1 1 3 3 3 5 5 5 n a r 3 3 3 Ð Ð 3 3 3 Ð Ð 3 3 3 o g n u , h e e r t n c m t + s i u e t e d l d s e i M e l s h s l t l 4 4 4 e e n i o 3 3 3 8 8 8 8 8 8 t e n B f a t 6 6 6 7 7 7 1 1 1 f Ð r d H r 1 1 1 1 1 1 e s e 3 o t o t o d a h e t t A o o o o o o h e e H t t t t t t r d 5 5 5 s l g n 2 2 2 8 8 8 0 0 0 b a 9 9 9 Ð Ð 9 9 9 Ð Ð 1 1 1 e a n a b % u T 0 y d l a 1 ) 1 . e 2 . m s i % s f y t s f n e 0 e 0 0 0 i b e 1 m n t e 0 6 0 3 0 0 6 0 3 0 0 6 0 3 0 e m ± r k 1 1 4 6 1 1 1 4 6 1 1 1 4 6 1 m h e t a r e y c i p i s # # # # # # # # # # # # # # # i b o v h u e e r : 5 0 0 0 T p d q y 1 6 1 0 4 3 6 5 1 6 1 0 4 3 6 5 1 6 1 0 4 3 6 l e t a $ $ $ r y i > > > > > > > > > > > > a p v c a s e i o s m e d n a ) C r n 2 , d y h e 0 r a c b d p e R a m h m e m ( s t u s e t a h m l n n h u f l t g 7 0 8 e n i m r 0 4 0 n e o e e m r c f x 2 1 2 o t i i S 1 1 1 m t s s a . . . t L 5 f m e a 1 1 1 n g i s e e D m a n l e e t S
R 0 1 C
R 5 1 C
R 6 1 C
u < o t o o l a s r v e p d s e s s e l e a s h n t e e n k d s n c t r n i a a a h h f l t r r = e o o A h F F + T
) 1 ) 2 ) 3 ) 4
© BSI
12-1999
Page 7 EN 10277-4:1999
I S B ) c ( , y p o C d e l l o r t n o c n U , 6 0 0 2 0 0 : 0 0 + T M G 9 1 : 6 0 : 4 0 6 2 t c O u h T , a n , n u d l e i f f e h s n u d l e i f f e h s : y p o C d e s n e c i L
Table 4 Ð Mechanical properties of alloy steels Designation Steel name
Thickness1)
Steel num ber
mm
16MnCrS5
16MnCrB5
20MnCrS5
16NiCrS4
15NiCr13
20NiCrM 20NiCrMoS2oS2-2 2
17NiCrM 17NiCrMoS6oS6-4 4
Mechanical properties1)
1.7139
1.7160
1.7149
1.5715
1.5752
1.6526 1.6526
1.6569 1.6569
5
+A2) + turned (+A +SH)
+A 2) + cold drawn (+A +C)
+FP3) + turned (+FP +SH)
+FP3) + cold drawn (+FP +C)
Hardness HB max.
Hardness4) HB max.
Hardness HB
Hardness4) HB
10
Ð
260
Ð
Ð
>10 #16
Ð
250
Ð
Ð
>16 #40
207
245
140 to 187
140 to 240
>40 #63
207
240
140 to 187
140 to 235
>63 #100
207
240
140 to 187
140 to 235
10
Ð
260
Ð
Ð
>10 #16
Ð
250
Ð
Ð
>16 #40
207
245
140 to 187
140 to 240
>40 #63
207
240
140 to 187
140 to 235
>63 #100
207
240
140 to 187
140 to 235
10
Ð
270
Ð
Ð
>10 #16
Ð
260
Ð
Ð
>16 #40
217
255
152 to 201
152 to 250
>40 #63
217
250
152 to 201
152 to 245
>63 #100
217
250
152 to 201
152 to 245
10
Ð
270
Ð
Ð
>10 #16
Ð
260
Ð
Ð
>16 #40
217
255
156 to 207
156 to 245
>40 #63
217
255
156 to 207
156 to 240
>63 #100
217
255
156 to 207
156 to 240
$
5
$
5
$
5
$
5
#
#
#
#
10
Ð
Ð
>10 #16
Ð
Ð
>16 #40
255
166 to 217
>40 #63
255
166 to 217
>63 #100
255
166 to 217
$
5
#
10
Ð
270
Ð
Ð
>10 #16
Ð
260
Ð
Ð
>16 #40
212
255
149 to 194
149 to 240
>40 #63
212
255
149 to 194
149 to 235
>63 #100
212
255
149 to 194
149 to 235
10
Ð
275
Ð
Ð
>10 #16
Ð
265
Ð
Ð
>16 #40
229
260
149 to 201
149 to 250
>40 #63
229
255
149 to 201
149 to 245
>63 #100
229
255
149 to 201
149 to 245
$
5
$
#
#
1)
For thicknesses
View more...
Comments
