BMW Rear-View Camera Retrofit for E65 and E66
Short Description
This documentation shows the walk through to adding a rear-view camera within your 7-Series BMW....
Description
Parts and Accessories. Installation Instructions. Rear-View Camera Retrofit BMW 7 Series (E 65 and E 66)
These installation instructions are only valid for cars with SA 609 (navigation system). Retrofit kit No.:
84 21 0 302 940
Installation time The installation time is approx 3.0 - 3.5 hours, but this may vary depending on the condition of the car and the equipment in it. Important information These installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies; In any event the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge. All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations. Ensure that the cables/lines are not kinked or damaged as you install them in the car. The costs incurred as a result of this will not be reimbursed by BMW AG. Additional cables/lines that you install must be secured with cable ties. If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used. Before you install the retrofit system, test the control module status with the CIP (coding, customising, programming) test program. If the test detects incorrect statuses in one or more control modules, these must be updated first using the “Load software” function. All the figures show LHD cars, proceed accordingly on RHD cars. Pictograms: !
denotes instructions that draw your attention to dangers. denotes instructions that draw your attention to special features.
!
denotes the end of the instruction or caution text.
See the EBA CD or Aftersales Portal for explanations of the pictograms. Do not archive the hard copy of these installation instructions since daily updates are made by Aftersales Portal. Subject to technical modifications.
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/1
List of special equipment The following special equipment must be taken into consideration when installing the retrofit kit: SA 609
Navigation system
Special tools required None
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/2
Contents Section
Page
1.
Parts Parts list list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
2.
Prep Prepar arat atio ions. ns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
3.
Conn Connec ecti tion on diagr diagram. am. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
4.
Inst Instal alla lati tion on and and cab cablin ling g dia diagr gram am . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
5.
To inst instal alll the the rea rearr-vie view w cam camer era a . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. .
9
6.
To inst install all and connec connectt the the contr control ol unit. unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.
To inst install all the the switc switchbo hbox. x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8.
To inst install all and connec connectt the the camer camera a cable. cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
9.
To inst install all and connec connectt the the power power supply supply cable cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
10. To inst install all and and conn connect ect the adap adapter ter cable cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 11. Conclu Concluding ding work work and and coding coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 12. Circui Circuitt diagra diagram m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/3
1.
Parts list
B
A
F
E
D
H
C
I
N
K
J
O
P
G
L
Q
M
R
065 0402 Z
Legend A
Camera cable
J
Miniature connector (5x)
B
Power supply cable
K
Cable tie 292 x 4.8 mm
C
Adapter cable
L
Cable tie 200 x 3.6 mm (20x)
D
Rear-view camera
M
Sealing strip (2x)
E
Control unit
Blue 4-pin socket casing
F
Switchbox
N O
Philips screw 3.5 x 16 mm (6x) (not required)
G
Protective strip
P
Philips screw 3.5 x 8 mm (4x) (not required)
H
Fillister head self-tapping screw 3.5 x 9.5 mm Q (2x) Fillister head self-tapping screw 4.2 x 13 mm R (4x)
I
© BMW AG, München
Moun Mounti ting ng plat plate e (no (nott req requi uire red) d) Moun Mounti ting ng plat plate e (not (not requ requir ired ed))
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/4
2.
Preparations
Conduct a brief test Disconnect the negative pole of the battery
TIS No. --12 00 ...
The following components must be removed first of all Trim for boot lid at bottom
51 49 005
Trim for boot lid at top
51 49 006
Centre rear lamp
63 21 186
Boot floor trim
51 47 101
Left boot – wheel arch trim
51 47 151
Right boot – wheel arch trim
51 47 161 -----
Control unit cover right (splash guard) Rear closing panel trim Navigation computer
© BMW AG, München
65 90 510
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/5
3.
Connection di diagram
A2
A3 A4 A5
A1
A6
A
A7 A8
B2
B
B3
A9
B4 B1
B5 B6 C2 C3 C4 C5
C
C1 C6 065 0386 Z
Item
Description
Signal
Cable colour / Cross-section
Connection location in the car
Abbreviation / Slot
---
---
A
Camera cable
---
---
A1
Black 12-pin socket casing
---
---
A2
Cable open
RFS
GN 0.75 mm2
A3
Cable open
RFS
GN 0.75
A4
Socket contact
Video +
A5
Socket contact
Video -
A6
Socket contact
RSF inv
A7 A8 A9
Cable open Cable open Socket contact
--To branch bran ch B1
PIN 24
To branch bran ch B1
PIN 11
To branch bran ch B1
PIN 23
To branch bran ch B2, B2, with miniature connector on red cable
PIN 25 PIN 12
mm2 mm2
Terminal 30
RT 0.75
Terminal 31
0.75 mm2
To branch bran ch B3, B3, with miniature connector on brown cable
TA
WS
Insulate and tie back
mm2
BR
0.25 mm2
© BMW AG, München
X709 PIN 1
mm2
SW 0.25
To left registration plate light or reversing light, with miniature connector on white/yellow cable Insulate and tie back
SW/BR 0.35
---
mm2
Transparent 0.14
To control unit E
EBA-Nr.: 01 29 0 300 852
---
Stand: 06.2003
EN/6
3.
Conn Connec ecti tion on diag diagrram
A2
A3 A4 A5
A1
A6
A
A7 A8
B2
B
B3
A9
B4 B1
B5 B6 C2 C3 C4 C5
C
C1 C6 065 0386 Z
Item
Description
Signal
Cable colour / Cross-section
Connection location in the car
Abbreviation Abbreviation / Slot
---
---
B
Power supply cable
---
---
B1
Blue 26-pin socket casing
---
---
B2
Cable open
B3 B4 B5 B6
Cable open Socket contact Eyelet M6 Socket contact
Terminal 30 Terminal 31 Terminal 30 Terminal 31
RT 0.75 mm 2 BR 0.75 mm 2 RT 0.75 mm 2 BR 0.75 mm 2
Terminal R VI/ WS 0.50
---
To branch bran ch A7, A7, with miniature connector on red cable
---
To branch bran ch A8, A8, with miniature connector on brown cable
---
Terminal 30 joint connector, behind module holder
X1889
Terminal 31 joint connector, below left tail light
X13094
To power module A71
X1856 PIN 18
mm 2
C
Adapter cable
---
---
C1
18-pin natural socket casing
---
---
C2
Socket contact
NAVR
To switchbox swi tchbox F
WS/RT
--To switchbox swi tchbox F
Socket contact
NAVG
WS/GN
X1312 PIN 3
To navigation unit plug A112
X1312 PIN 4
To navigation unit plug A112
X1312 PIN 5
To navigation unit plug A112
X1312 PIN 13
0.35 mm 2 C4
Socket contact
NAVB
VI 0.35
C5
Socket contact
C6
Blue 4-pin plug casing
NAV_31
---
© BMW AG, München
mm 2
Shield
---
---
To navigation unit plug A112
0.35 mm2 C3
---
To disconnected cables in car, with socket casing N
EBA-Nr.: 01 29 0 300 852
---
Stand: 06.2003
EN/7
4.
Inst Instal alla lati tion on and and cab cabli ling ng diag diagrram
1 E65
A E D
C
F
2
3
4
B 065 0369 Z
Legend A
Camera cable
B
Power supply cable
C
Adapter cable
D
Rear-view camera
E
Control unit
F
Switchbox
1
Power module A71, A71, plug X1856
2
Navigation computer A112
3
Terminal 30 joint connector X1889
4
Terminal 31 joint connector X13094
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/8
5.
To inst instal alll the the rear rear--view view came camerra Mark the dimensions on the rear lamp (2) and cut out in the marked area (1) with a saw.
1 8 mm
2
76 mm
38 mm
108 mm
065 0378 Z
1
Mark the dimensions on the rear lamp (2) and drill dril l out the drilling positions positions (1) with a 3.5 mm twist drill bit.
1
Countersink the drilling positions (1). 38 mm
2
7 mm
7 mm 065 0379 Z
Use fillister head self-tapping screws H to screw rear-view camera H firmly onto the rear lamp (1).
D
1
H
H 065 0380 Z
Route the cable (3) of the rear-view camera through the opening (2) in the boot lid (1).
1
Fit the rear lamp (4).
2 3
4 065 0381 Z
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/9
6.
To ins insta tall ll and and con conne nect ct the the con contr trol ol unit unit Do not damage the external panel of the boot lid.!
1
Mark the dimensions on the boot lid (2) and drill out the drilling position position (1) with a 6 mm twist drill bit. Deburr the hole and coat the bare surfaces with preservative. 15 mm
15 mm
2 065 0382 Z
Do not cut through the cable loop (1). !
G
1 Connect the connection plug (2) of the rear-view camera and branch A1 onto A1 onto control unit E. Affix protective strip G to control unit E.
E
Cut off any excess lengths.
A1 2 065 0371 Z
X709
Use a cable tie K to to secure control unit E to the hole (1) in the boot lid (2).
E
A2
Route branch A2 to A2 to plug X709 of X709 of the registration plate light. Use miniature connector J to connect branch A2 to the white/yellow cable of plug X709 (PIN X709 (PIN 1).
K
1
J
2 065 0370 Z
Danger of kinking and chafing. Camera cable A must be attached to the existing wiring harness using cable ties L.! !
L
1 2
Route camera cable A through the hinge pillar (1) into the boot to the fuse holder (2).
A 065 0385 Z
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/10
7.
To ins insta tall ll the swit switc chbo hbox Affix sealing strip M to the rear of switchbox F.
F
M
065 0403 Z
Depending on the equipment in the car, there are two possible ways of installing switchbox F.! First possibility Place switchbox F against the front base support system (1) and transfer two holes.
1
Drill through the front base support system (1) with a 3.5 mm twist drill bit.
F
Screw switchbox F on firmly using fillister head self-tapping screws I.
I 065 0383 Z
Second possibility
I 1
Place switchbox F against the holder (1) and transfer three holes. Drill through the holder (1) with a 3.5 mm twist drill bit.
F
Screw switchbox F on firmly using fillister head self-tapping screws I.
I 065 0384 Z
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/11
8.
To ins insta tall ll and and conn connec ectt the the came camerra cab cable le Route camera cable A to the right side of the boot.
A
065 0372 Z
Route camera cable A to switchbox F.
1
A
Remove the draw-in tool (1).
F 065 0400 Z
A3
Insulate branch A3, A3, green cable, and branch A9, A9, white cable, and tie them back.
A9
Connect branches A4 – A6 to A6 to branch B1, B1, blue plug, as follows: - Branch A4, A4, transparent cable, in PIN 24 - Branch A5, A5, black/brown cable, in PIN 11 - Branch A6, A6, black cable, in PIN 23
B1 A4-A6 065 0373 Z
B2
A7-A8
Connect branches A7 and A7 and A8 to A8 to branch B1, B1, blue plug, as follows: - Branch A7, A7, red cable, with miniature connector J to branch B2, B2, red cable (PIN 25) - Branch A8, A8, brown cable, with miniature connector J to branch B3, B3, brown cable (PIN 12)
B34 B1
J 065 0374 Z
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/12
9.
To inst instal alll and and conn connec ectt the the powe powerr supp supply ly cab cable le
B5
Unfasten tied-back joint connector connector terminal 30 X1889 (red/white X1889 (red/white cable).
B4
Connect branch B4, B4, red cable, to joint connector terminal 30 X1889. X1889.
X13094
Screw branch B5, B5, brown cable, onto joint connector terminal 31 X13094. X13094 .
X1889 065 0419 Z
Connect branch B1, B1, blue plug, to switchbox F.
B1
F
065 0387 Z
Route branch B6, B6, violet/white cable, to the boot on the right.
B6
065 0367 Z
Route branch B6, B6, violet/white cable, to the power module (1).
1
Connect branch B6, B6, violet/white cable, to PIN 18 of plug X1856. X1856. If pin chamber 18 is occupied, use miniature connector J to connect branch B6 to B6 to the violet/white cable of PIN 18. !
B6 X1856
065 0376 Z
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/13
10. To install install and and connec connectt the adapter adapter cable
1
Disconnect the following cables (1) from plug X1312 of X1312 of the navigation computer (2):
N
- Red Red cabl cable e from from PIN PIN 3 - Gree Green n cab cable le from from PIN PIN 4 - Blue Blue cabl cable e fro from m PIN PIN 5 - Shiel hield d fro from m PIN PIN 13
2
X1312
Connect the disconnected cables into socket casing N as follows: 065 0388 Z
- Red cable able in PIN PIN 3 - Gree Green n ca cable ble in in PIN PIN 1 - Blue lue cab cable le in PIN PIN 2 - Shiel ield in PIN PIN 4
Connect branches C2 – C5 as C5 as follows to plugX1312 plugX1312 of of the navigation computer (1):
C2-C5
- Branch C2, C2, white/red cable, in PIN 3 - Branch C3, C3, white/green cable, in PIN 4 - Branch C4, C4, violet cable, in PIN 5 - Branch C5, C5, shield, in PIN 13
1
X1312
065 0389 Z
C6 N
Connect socket casing N to branch C6, C6, blue plug. Connect branch C1, C1, natural colour plug, to switchbox F.
C1 F 065 0390 Z
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/14
11. 11. Conclu Concludin ding g work work and coding coding This retrofit system does not require coding. - Conn Connec ectt the the batt batter ery y - Cond Conduc uctt a brie brieff tes testt Check the function of the rear-view camera as follows: - Swit Switch ch on the the ign ignit itio ion n - Dea Deacti ctivat vate e the help help text texts s in the the Setting Settings s menu menu - Sele Select ct the Navi Naviga gatio tion n men menu u - Select Select fullfull-scr screen een displ display ay in the the Naviga Navigatio tion n menu - Engage Engage reverse; reverse; an image image must must appear appear on the the on-board on-board monitor monitor - Dise Diseng ngag age e reve revers rse e gear gear The on-board monitor must switch over after about 5 seconds.
- Re-a Re-ass ssem embl ble e the the car car
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/15
12. 12. Cir Circuit cuit diag diagrram
1 3 _ V A N
3 1
B V A N
5
I V 5 3 , 0
6 1
4
N G / S W 5 3 , 0
7 1
2 1 1 A
G V A N
m r i h c S
T R / S W 5 3 , 0
3
R V A N
2 1 3 1 X
8 1
1 3 _ 4 V A N
m r i h c S
I V 5 3 , 0
2 B V A N
4 1
T R / S W 5 3 , 0
3 R V A N
5 1
N G 5 7 , 0 x
3 S F R
N G 5 7 , 0 x
4 A T
S W 5 2 , 0 x
x S W 5 3 , 0
o e d i V
1 3
4
x T R 5 3 , 0
0 3
* 1 X
© BMW AG, München
R V A N
1 3 _ V A N
B V A N
G V A N
R V A N
* 3 A
* 5 X
* 4 X
T R 5 7 , 0 x
2 1
1 3
5 2 0 3
R B 5 7 , 0 x
4 9 0 3 1 X
T R 5 7 , 0 x
9 8 8 1 X
3 1 1 3
0 3
6 2
+ o e d i V
3
W S 5 3 0 x
* 6 X
2
0 3
* 1 A
G V A N
9 0 7 X
R B 5 7 , 0 x
* 2 A
1
Z 1 9 3 0 5 6 0
B V A N
* 7 X
1
1 3
2
1 3 _ V A N
* 9 X
* 3 X
E G 5 3 , 0 x
6
3 1
N G / S W 5 3 , 0
1 G V A N
9
v n i F S R
+ o e d i V
o e d i V
3 v n 2 i F S R
5
x W S 5 2 , 0
6
t n e r a p s n a r t 4 1 , 0
x
4 2
x R B / W S 5 3 , 0
* 2 X
EBA-Nr.: 01 29 0 300 852
x S W / I V 0 5 , 0
o e d i V
* 8 X
8 1 R
0 1 R
1 1
2 1
+ o e d i V
* 8 X
1 7 A
6 5 8 1 X
Stand: 06.2003
EN/16
12. 12. Circ Circuit uit diagr diagram am Legend A1* A2* A3*
Rear-view camera Control unit Switchbox
A112 A71
Navigation computer Power module
X1* X2* X3* X4* X5* X6* X7* X8* X9*
Black 4-pin socket casing Black 12-pin socket casing Blue 4-pin socket casing Miniature connector Miniature connector Socket contact Cable open Blue 26-pin socket casing 18-pin natural socket casing
X709 X1312 X1856 X1889 X13094
Blue 3-pin plug Black 20-pin plug Black 18-pin plug Terminal 30 joint connector Terminal 31 joint connector
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram
Cable colours BL BR GE GN GR RT SW VI WS
Blue Brown Yellow Green Gr e y Red Black Violet White
© BMW AG, München
EBA-Nr.: 01 29 0 300 852
Stand: 06.2003
EN/17
View more...
Comments
