Benq Q7T3-FP731
Short Description
Q7T3-FP737S Dual function LCD Monitor Service Guide Alignment Procedure...
Description
Q7T3-FP737S Dual function LCD Monitor Service Guide Alignment Procedure 1. Alignment procedure (for function adjustment) A. Preparation: 1.
Setup input timing ICL-605, 32-Grays pattern.
2.
Setup unit and keep it warm up at least 30 minutes.
B. Timing adjustment: 1. Enter factory setting area (press “ENTER”, “EXIT” and then press “SOFTPOWER”). 2. Check the settings to following values: Contrast = 50 Brightness = 90 Volume = 30 OSD time = 20 Color = sRGB Language = English Then, turn off the monitor power. 3. Turn on power enter user area. C. Color balance adjustment: 1. Enter factory setting area (press “ENTER”, “EXIT” and then press “SOFTPOWER”). 2. Setup input timing ICL-605 (1280*1024 75Hz), 5-MOSAIC pattern.(timing 202 pattern 42) 3. Press”I-key”,to enter window for whitebalance and burning mode. 4. Press “Whitebalance”, to Calibrate ADC. 5. Setup input timing ICL-605, 32 -Gray pattern. 6. Checking if the picture is no good, reject this monitor. D. Color adjustment: 1. Setup input timing ICL-605, white pattern. 2. Measure color temperature by Minolta CA-110 (or equivalent equipment). 3. Alignment the color temperature Bluish, Reddish & sRGB. The color temperature specification as follows: White Balance (Bluish, 9300K set on OSD)
X+-
0.283+(-) 0.03
Y+-
0.297+(-) 0.03
White Balance (Reddish, 5800K set on OSD)
X+-
0. 326+(-) 0.03
Y+-
0. 342+(-) 0.03
White Balance (sRGB, 6500K set on OSD)
X+-
0. 313+(-) 0.03
Y+-
0. 329 +(-) 0.03
1 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Alignment Procedure 4. Turns off the monitor power. E. Writing EDID file: 1. Setup a PC with DDC card. 2. Connect PC to monitor with a D-sub signal cable. 3. Please refer to the C212 for the correct EDID file. 4. Runs the writing program to write the EDID file into EEPROM for analog input, ie. 15-pin D-sub. 5. Read both EEPROM data and confirm it to match with the C212 document definition. 6. Connect PC to monitor with a DVI-D signal cable. 7. Please refer to the C212 for the correct EDID file. 8. Runs the writing program to write the EDID file into EEPROM for DVI input, ie. 24-pin DVI-D. 9. Read both EEPROM data and confirm it to match with the C212 document definition.
2 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Alignment Procedure F. Command definition: PC Host will send 0x7C IIC slave address and then following 4 bytes command I2C Send Command Byte1 Byte2 Byte3 Byte4 Write Contrast CA 55 Data checksum Write Brightness CA 56 Data checksum Write Red Gain CA 57 Data checksum Write Green Gain CA 58 Data checksum Write Blue Gain CA 59 Data checksum Read Contrast C3 55 XX checksum Read Brightness C3 56 XX checksum Read Red Gain C3 57 XX checksum Read Green Gain C3 58 XX checksum Read Blue Gain C3 59 XX checksum Write C1 (Bluish) R-Gain Data to NVRAM AA 3C Data checksum Write C1 (Bluish) G-Gain Data to NVRAM AA 3D Data checksum Write C1 (Bluish) B-Gain Data to NVRAM AA 3E Data checksum Write C2 (sRGB) R-Gain Data to NVRAM AA 4C Data checksum Write C2 (sRGB) G-Gain Data to NVRAM AA 4D Data checksum Write C2 (sRGB) B-Gain Data to NVRAM AA 4E Data checksum Write C3 (Reddish) R-Gain Data to NVRAM AA 5C Data checksum Write C3 (Reddish) G-Gain Data to NVRAM AA 5D Data checksum Write C3 (Reddish) B-Gain Data to NVRAM AA 5E Data checksum Write User R-Gain Data to NVRAM AA 6C Data checksum Write User G-Gain Data to NVRAM AA 6D Data checksum Write User B-Gain Data to NVRAM AA 6E Data checksum Read C1 (Bluish) R-Gain data from NVRAM A3 3C XX checksum Read C1 (Bluish) G-Gain data from NVRAM A3 3D XX checksum Read C1 (Bluish) B-Gain data from NVRAM A3 3E XX checksum Read C2 (sRGB) R-Gain data from NVRAM A3 4C XX checksum Read C2 (sRGB) G-Gain data from NVRAM A3 4D XX checksum Read C2 (sRGB) B-Gain data from NVRAM A3 4E XX checksum Read C3 (Reddish) R-Gain data from NVRAM A3 5C XX checksum Read C3 (Reddish) G-Gain data from NVRAM A3 5D XX checksum Read C3 (Reddish) B-Gain data from NVRAM A3 5E XX checksum Read User R-Gain data from NVRAM A3 6C XX checksum Read User G-Gain data from NVRAM A3 6D XX checksum Read User B-Gain data from NVRAM A3 6E XX checksum Change Color Temperature to C1 (Bluish) CC 1 XX checksum Change Color Temperature to C2 (sRGB) CC 2 XX checksum Change Color Temperature to C3 (Reddish) CC 3 XX checksum Change Color Temperature to User CC 4 XX checksum 3 Confidential
Q7T3-FP737S Dual function LCD Monitor Service Guide Alignment Procedure User mode to factory mode Auto Color (Offset1, Offset2, Gain) Factory mode to User mode Clear user area data On burn in mode Off burn in mode Change Language Setting
1A 1B 1E 1F CE CE 66
5A 5A 5A 5A 1 XX* 0~7
XX XX XX XX XX XX XX
checksum checksum checksum checksum checksum checksum checksum
*: Any value except 1 can off burn-in mode Read EEPROM Bank-0 Read EEPROM Bank-1 Read EEPROM Bank-2 Read EEPROM Bank-3 Read EEPROM Bank-4 Read EEPROM Bank-5 Read EEPROM Bank-6 Read EEPROM Bank-7 Write EEPROM Bank-0
B0 B1 B2 B3 B4 B5 B6 B7 B8
Address Address Address Address Address Address Address Address Address
XX XX XX XX XX XX XX XX Data
checksum checksum checksum checksum checksum checksum checksum checksum checksum
Write EEPROM Bank-1
B9
Address
Data
checksum
Write EEPROM Bank-2
BA
Address
Data
checksum
Write EEPROM Bank-3
BB
Address
Data
checksum
Write EEPROM Bank-4
BC
Address
Data
checksum
Write EEPROM Bank-5
BD
Address
Data
checksum
Write EEPROM Bank-6
BE
Address
Data
checksum
Write EEPROM Bank-7
BF
Address
Data
checksum
Note A: Byte4(Checksum) = Byte1 + Byte2 + Byte3 Note B: Data = The value write to MCU Note C: XX = don't care, any value( Q4 will ON. That will make 3.3_M = 3.3V.
R16
C8 47P J
10K
C9 47P J
A
C
14
TP12
75
C6 47P J
A
PC5V + + -
TP11
R4
DSUB_SCL K
1
13
17
Q3 2N3904 2
PC5V_OFF
TP9
DSUB_SDA
1
3 R15 1K
12
A
R9 4.7K
TP6
R3
TP3 TP4
6 1 7 2 8 3 9 4 10 5
11
47
R2
J1
K
PC5V
R5
16
Q2 2N3906 2 3
3.3V_MCU 3.3V_MCU
DN4 1
DVIPC5V
BAV70LT1
K
3
2
R101 RX0-
J
RX0+
10
A
RX0P
RX1RX1+
TP92 TP93
RX2RX2+
A J
RX1M K
TP94 TP95
DVISDA DVISCL
RX1+
TP96 TP97
DVIPC5VGND TP98
R24
BAV99 DN7
10 R104
J
RX1P
RX2-
BAV99 DN8
RX2+
J
WP
7
B
3
A2
SCL
6
R22
4
GND
SDA
5
R23
47
DVISCL DVISDA
AT24C02
RX2P 10
J
RXCM 10
A
R108 J
RXCP 10
BAV99 DN12 K
A
Benq Corporation
A
J
D-detect
Project Code 99.L8372.001 Title
A
OEM/ODM Model Name
Q7T3 INTERFACE BOARD
Size PCB P/N 48.L8301.S72 Date:
3
2
PCB Rev. Document Number 99.L8372.000-C3-304-006
S72
Tuesday, December 23, 2003 Sheet Prepared By Reviewed By ANGEL HU
4
Model Name
A
BAV99 C49 DN14 0.01U K
5
47
R107
BAV99 DN11
BZV55-C5V1 A
A
BZV55-C5V1
A1
R106
BAV99 DN10
RXC+
D8
2
R21 4.7K
A
D7 BZV55-C5V1
K
K
K D6
8
RX2M
BAV99 DN9
K
RXC-
VCC
10
K 3.3V_MCU
A0
R105
10K
J101
C101 0.01U K
1
10
J K
TP90 TP91
RX1-
K
RX0RX0+
20 18 16 14 12 10 8 6 4 2
A
RX2RX2+
TP88 TP89
19 17 15 13 11 9 7 5 3 1
A
RX1RX1+
2061106210
RXCRXC+
R103
A
RX0RX0+
TP86 TP87
10
A
RXCRXC+
BAV99 DN6
R20 4.7K
U1
R102 J K
B
BAV99 DN5
C10 0.1U K
RX0M K
DVIPC5V
ARSENIO LIU 1
1
6 of Approved By ARIES CHU
R ev. 0
5
4
3
2
1
3.3V_MCU
VAD
C11 0.1U
VDVI VDPLL VPLL
C12 0.1U
C13 0.1U
C14 0.1U
C15 0.1U
C16 0.1U
C17 0.1U
3.3V_MCU
D
D
VDVI R25
18 87 97 117
RA1P RA1N RA2P RA2N RA3P RA3N
GA1P GA1N GA2P GA2N LVA3p/GA3P LVA3M/GA3N
98 99 100 101 102 103
GA1P GA1N GA2P GA2N GA3P GA3N
BA1P BA1N BA2P BA2N BA3P BA3N
88 89 90 91 92 93
BA1P BA1N BA2P BA2N BA3P BA3N
NC/RB1P NC/RB1N NC/RB2P NC/RB2N NC/RB3P NC/RB3N
16 17 22 23 24 25
RB1P RB1N RB2P RB2N RB3P RB3N
NC/GB1P NC/GB1N NC/GB2P NC/GB2N NC/GB3P NC/GB3N
8 9 12 13 14 15
GB1P GB1N GB2P GB2N GB3P GB3N
118 119 120 121 122 123 124 125 128 1 4 5
CLKAP CLKAN CLKBP CLKBN
NC/ESP OSP GPO0 GPO1 GPO2 GPO3 GPO4
75 76 83 82 81 80 79
ESP OSP GPO0 GPO1 GPO2 GPO3 GPO4
AD0 AD1 AD2 AD3 BUS TYPE/NC
30 77 78 31 6
U2
390 F MST8116B
C28 0.1U
3 3 3
B
CSZ RDZ WRZ
REFP
67
REFM
69 71 70 32 72
R202 100
RESET
66
INT
LVB3P/CLKAP LVB3M/CLKAN LVBCKMP/NC/CLKBP LVBCKP/NC/CLKBN LVB2P/NC LVB2M/NC LVB1P/NC/BB1P LVB1M/NC/BB1N LVB0P/NC/BB2P LVB0M/NC/BB2N NC/BB3P NC/BB3N
R65
10K
73 74
PWM0 PWM1
33
XIN
1
C34
4.7U 25V
2
C54 + R28 30K
C33 0.1U
Y1 14.318MHZ
4.7P C C35
R201 1M 34
XOUT
3.3V_MCU
1 220 OHM
220 OHM +
C19 22U 16V
C20 0.1U
C18 22U 16V
C23 0.1U
VDPLL VDVI L3
220 OHM
+
3.3V_MCU
C
L4 220 OHM
C45 22U 16V
C24 0.1U
C27 0.1U
Add C45 for Diagonal noise. Also reverse L1 and C19. L1, L3 and L4 change to 0 ohm for power ripple reduction.
+2.5V
C29 0.1U
Current setting=Direct DDR Bus
C30 0.1U
C31 0.1U
C32 0.1U
B
BUStype=Low : 3-wire Bus
TXO2+ TXO2-
BB1P BB1N BB2P BB2N BB3P BB3N
GNDC GNDC GNDC GNDC
AD0 AD1 AD2 AD3
pin 68: NC (MST suggested), 10/14. ** R28 & C33 are reserved for ESD
3.3V_MCU
Benq Corporation R26 4.7K
Project Code 99.L8372.001 Title
Model Name
OEM/ODM Model Name
Q7T3
PCB Rev. Document Number S72
99.L8372.000-C3-304-006
Tuesday, December 23, 2003 Date: Sheet Prepared By Reviewed By ANGEL HU 3
2
A
INTERFACE BOARD
Size PCB P/N 48.L8301.S72
R27 OPEN
0
4
+
3.3V_MCU
** R28 & C33 are reserved for ESD 5
VPLL L2
19 86 96 116
GNDP GNDP GNDP GNDP GNDP GNDP GNDP 10 20 85 95 105 115 127
AVSS_DVI AVSS_DVI AVSS_DVI 39 42 48
36
68 56 64
R203
AVSS AVSS AVSS
0.1U
AVSS_PLL
BYPASS AVSS_LPLL
54
A
3 2
AVSS_MPLL
C36 4.7P C
VAD
BUStype=High: Direct DDR Bus
CSZ/ALE SCL/RDZ SDA/WRZ HWRESETZ INT
12M
BRT_ADJ
3.3V_MCU L1
TXEC+ TXEC-
2
53
11 21 84 94 104 114 126 VDDP VDDP VDDP VDDP VDDP VDDP VDDP
VDDC VDDC VDDC VDDC
106 107 108 109 110 111 112 113
1
R+ RG+ GB+ BCK+ CKREXT
LVACKP/NC LVACKM/NC LVA2P/RA1P LVA2M/RA1N LVA1P/RA2P LVA1MRA2N LVA0P/RA3P LVA0M/RA3N
1
40 41 43 44 46 47 49 50 52
AVDD_PLL
45 51
35
RIN0 RIN0M GIN0 GIN0M SOGIN0 BIN0 BIN0M HSYNC0 VSYNC0 DDC1_CLK/GPO8 DDC1_DAT/GPO7
2
RX2P RX2M RX1P RX1M RX0P RX0M RXCP RXCM
C
63 62 60 59 61 58 57 37 38 29 28
2
BLUE+ BLUEHSYNC VSYNC
AVDD_DVI AVDD_DVI
RED+ REDGREEN+ GREEN-
AVDD_MPLL
AVDD AVDD
55 65
+2.5V
ARSENIO LIU
2
6 of Approved By ARIES CHU
1
R ev. 0
5
4
3
2
1
8 7 6 5
4.7K
RN7
4.7K
RN4
8 7 6 5
1 2 3 4
3.3V_MCU
3.3V_M
1 2 3 4
ENTER INC DEC EXIT
C43 0.1U K
3.3V_M 3.3V_MCU
LED_ORG D
3.3V_M
C301
4.7K
C46
0
0.1U K
22P J
R301要靠近MCU
Y2 12MHZ
C47
R308 1M
22P J
39
DA9/HALFV
38
9
P6.3/AD3
10
VSS
11
X2
U5
VOLUME
X1
13
ISDA/P3.4/T0
14
ISCL/P3.5/T1
15
STOUT/P4.2
37
VBLANK/P4.0
36
DA7/HCLAMP
35
MTV312MV64
16
P6.2/AD2/HLFHI
17
P1.0
A1
WP
7
3
A2
SCL
6
S CL
4
GND
SDA
5
S DA
P6.0/AD0
4.7K
D
MUTE
DA6/P5.6
34
P6.7/DA13
33
P6.6/DA12
32
PANEL_ON
P6.5/DA11
31
A-detect
I-KEY BLT_ON
P6.4/DA10
30
PW_SW
HSCL/P3.0/Rxd
29
DSUB_SCL
C
R307 10K
2
28
27
P6.1/AD1
P1.7
26
25
P1.5
P1.6 24
23
P1.3
P1.2
P1.4 22
21
20
P3.2/INT0
P1.1 18
19
4.7K
RN5
HBLANK/P4.1
SOCKET P/N: 22.10079.044
12
S DA S CL
C
8
1 2 3 4 DA8/HLFHO
VDD
8 7 6 5
Delete: Change PWR_OFF to VOL_ON_OFF on P6.2.
RN3
40
41
DA5/P5.5
DA4/P5.4
43
42
HSYNC
DA3/P5.3
1
44 VSYNC
DA2/P5.2
3
2 DA1/P5.1
VDD3
DA0/P5.0
RST
8
1 2 3 4
3.3V_M
4
6 7
R301
12M
5
8 7 6 5 R88
VCC
AT24C04N-10SI-2.7
HSDA/P3.1/Txd
C301 要靠近Scaler
NC
NC 3.3V_MCU 3.3V_M
3.3V_M
R31 4.7K
A0
LED_GRN
C44 0.22U K
R30 4.7K
U4 1
DSUB_SDA AD0
R43
100
PC5V_OFF D-detect 1 2 3 4
RESET
WRZ
8 7 6 5
CSZ
4.7K
RN2
AD1 INT AD2 AD3
3.3V_M 3.3V_MCU
8 7 6 5
8 7 6 5
4.7K
RN1
4.7K
RN6
1 2 3 4
1 2 3 4
RDZ
3.3V_MCU
R77 220
3.3V_MCU R76 220
R303 1k
LED_GRN
MUTE
CON1
2
3
R302 1k
Q6 2N3904
1
R0603
TP26
Q7 2N3904
1
R0603
1 2 3 4 5 6 7 8 9
TP27
2
LED_ORG
3
3.3V_MCU
200ms
200ms 1K INC ENTER EXIT DEC PW_SW I-KEY
B
VOL_ON_OFF
L12 L13 L10 L11 L301 L302
R46
TP28 TP29
R47 1K R44 1K
TP30 TP31
R45 1K R3041K
TP32 TP33
R3051K
C41 100P 50V J
C42 100P 50V J
C39 100P 50V J
C40 100P 50V J
C303 100P 50V J
B
2060091109
C302 100P 50V J
C53 0.1U K
C52 0.1U K
J4 3.3V_MCU
3.3V_MCU
220 OHM 1
VIN
MUTE
1
TP156
+2.5V
2072060207
2
+ C73 47U 25V
C77 0.1U K
C80 0.1U K
C76 0.1U K
C71 0.1U K
C60 0.1U K
+ C79 0.1U K
C78 0.1U K
C74 47U 25V
R309
0
GMT
U6
TP154
1
TP155
BRT_ADJ L6
VOUT
3 1
TP153 Z30 VOLUME
TP152
1 3 TP157 5 7 9 11 13
+ C57
G950T65U 22U 25V
2
L5
GND GND
2 4 6 8 10 12 14
2 G1
TP151
BLT_ON
2
+5V
C61 0.1U K
A
A
Benq Corporation Project Code
Model Name
99.L8372.001 Title Size P CB P/N 48.L8301.S72 D ate:
4
3
2
PCB Re v. Document Number S72
99.L8372.000-C3-304-006
Tuesday, December 23, 2003 Sheet Prepared By Reviewed By ANGEL HU
5
OEM/ODM Model Name
Q7T3 INTERFACE BOARD
ARSENIO LIU 1
3
of 6 Approved By ARIES CHU
Rev. 0
5
4
3
2
1
+5V 5V_PANEL
D
R57 100K
Q4 AO3401
G
1
LCD_PW
+ C68
D
20K
Q5 2N3904
1
D
22U 25V
2
R61
G(1)
2
PANEL_ON
S
3
+5V
C69 0.1U K
D(3)
S(2)
20K2085030
C
TP64 BB2N BB2P BB1N BB1P TXO2TXO2+ CLKBN CLKBP CLKAN CLKAP RA3N RA3P RA2N RA2P B
RA1N RA1P TXECTXEC+ GA3N GA3P
5V_PANEL
TXO0TXO0+ TXO1TXO1+ TXO2TXO2+
TP43 TP44 TP45 TP46 TP47 TP48
TXOCTXOC+ TXE0TXE0+
TP49 TP50 TP51 TP52 TP53 TP54
TXE1TXE1+
TP55 TP56
TXE2TXE2+ TXECTXEC+ TXE3TXE3+
TP57 TP58 TP59 TP60 TP61 TP62
G2 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1
TP63
G2 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1
C
B
Benq Corporation Project Code
J5
C401 0.1U K
99.L8372.001 Title Size PCB P/N 48.L8301.S72
4
3
2
A
PCB Rev. Document Number S72
99.L8372.000-C3-304-006
Tuesday, December 23, 2003 Sheet Prepared By Reviewed By ANGEL HU
5
OEM/ODM Model Name
Q7T3 INTERFACE BOARD
A
Date:
Model Name
4
ARSENIO LIU
of 6 Approved By ARIES CHU
1
Re v. 0
5
4
3
2
1
D
D
Screw Holes
Optical Points
OP1 OP
OP2 OP
OP3 OP
OP4 OP
OP5 OP
OP6 OP
OP7 OP
9
5
4
8
4
8
3 2
7
3
6
2
1
5
1
9
1
C
5
1
C
9
5
4
8
4
8
7
3
7
3
7
6
2
6
2
6
H1
H2
H3
H4
HOLE-V8
HOLE-V8
HOLE-V8
HOLE-V8
9
OP8 OP
OP9 OP
OP10 OP
OP11 OP
OP12 OP
OP13 OP
OP14 OP
B
B
Benq Corporation
A
Project Code 99.L8372.001 Title
Model Name
INTERFACE BOARD
Size PCB P/N 48.L8301.S72
PCB Rev. Document Number 99.L8372.000-C3-304-006
S72
Tuesday, December 23, 2003 Date: Sheet Reviewed By Prepared By ANGEL HU 5
4
3
2
A
OEM/ODM Model Name
Q7T3
ARSENIO LIU 1
5
6 of Approved By ARIES CHU
R ev. 0
5
4
3
2
1
D
D
20K2167050 TP99 RA3N RA3P RA2N RA2P RA1N RA1P GA3N GA3P GA2N GA2P C
GA1N GA1P
RA3N RA3P
FB0N FB0P
TP100 TP101
RA2N RA2P
FB1N FB1P
TP102 TP103
RA1N RA1P
FB2N FB2P
TP104 TP105
GA3N GA3P
FG0P FG0N
TP106 TP107
GA2N GA2P
FG1N FG1P
TP108 TP109
GA1N GA1P
FG2N FG2P
TP110 TP111 TP112 TP113
CLKAP CLKAN BA3N BA3P BA2N BA2P BA1N BA1P OSP ESP
OSP GPO1 GPO0
ESP
5 6 7 8
GPO3 GPO2 GPO4 B
5 6 7 8 22 4 3 2 1
BA3N BA3P
FR 0N FR0P
TP114 TP115
BA2N BA2P
FR 1N FR1P
TP116 TP117
BA1N 22 BA1P RN8 4 3 2 1
FR 2N FR2P
TP118 TP119
LP POL
TP120 TP121 TP122 TP123
CLKV STV OE
TP124 TP125 TP126
RN9 LCD_PW TP132
C602 0.1U K
G2 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1
C
20K2167030 TP127 RB3N RB3P RB2N RB2P RB1N RB1P GB3N GB3P J7
GB2N GB2P GB1N GB1P
RB3N B0N RB3P B0P
TP128 TP129
RB2N B1N RB2P B1P
TP130 TP131
RB1N B2N RB1P B2P
TP133 TP135
GB3N BG0N GB3P BG0P
TP136 TP137
GB2N BG1N GB2P BG1P
TP138 TP139
GB1N BG2N GB1P BG2P
TP140 TP141 TP142 TP143
CLKBP CLKBN BB3N BB3P
A
BB2N BB2P BB1N BB1P
BB3N BR0N BB3P BR0P
TP144 TP145
BB2N BR1N BB2P BR1P
TP146 TP147
BB1N BR2N BB1P BR2P
TP148 TP149
G2 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 G1
B
Benq Corporation Project Code 99.L8372.001 Title
3
PCB Rev. Document Number S72
99.L8372.000-C3-304-006
Tuesday, December 23, 2003 Date: Sheet Prepared By Reviewed By ANGEL HU
4
OEM/ODM Model Name
Q7T3
2
A
INTERFACE BOARD
Size PCB P/N 48.L8301.S72 J6
5
Model Name
ARSENIO LIU
6
6 of Approved By ARIES CHU
1
R ev. 0
Q7T3(CPT panel) LCD Monitor Service Guide Trouble Shooting Q7T3-CPT TROUBLE SHOOTING GUIDE 1.No Display or display is unstable No picture or picture unstable
Power off
Yes
Turn on power
No
Does cable plugs in
No
Check all of wire then turn on power
connector?
switch again.
Yes
Does power stable?
No
Check Power BD
Yes
Is LED light green/orange?
No
Check control BD
Yes
Is LED status normal?
No
Check Flash Rom or replace it
Yes
Does crystal work correctly?
No
Check crystal CKT or replace it
No
Replace interface BD
Yes
Is interface BD normally? Yes
Replace panel
1
Q7T3(CPT panel) LCD Monitor Service Guide Trouble Shooting 2. BUTTON function: OSD is not working Yes
Is control BD connecting?
No
Plug control BD then retry
Yes
Is bottom switch normally?
Yes
Replace control BD then retry
No Replace Control BD Is OSD working??
No Check Interface BD
3. OSD function: OSD doesn’t work
Is control BD working?
No
Replace control BD
Check interface BD
2
Q7T3(CPT panel) LCD Monitor Service Guide Trouble Shooting 4. Power Board
Backlight didn't shine
Y
Y Replace Q761
IC751 PIN 9 IS 15V? N
LED shined? N
N Plug CN701 again or checking I/F BD
Y PWM existed? (BLT_ADJ)
3.3V existed?
IS I/F board connected? Y
Y N Plug CN601 again or checking PW BD
Replace new fuse Turn on level existed? (BLT_ON)
N
Y
Replace new fuse
N Insert them again
N
Y Check CN752, CN753 was pluged properly?
Check IC701 OK?
Replace IC701
Y N Replace IC751,Q751
Y Checking F601 Broke?
Replace new fuse
N
Y Check IC601 Vcc existed?
Replace IC601,ZD601,C606, C611
N
Replace IC602, IC702,D702 or check I/F BD
3
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification Table of Contents
1. Introduction ...................................................................................................................................4 2. Operational Specification ..........................................................................................................5 2.1 Environment.................................................................................................................................5 2.1.1 Temperature ..................................................................................................................................................... 5 2.1.2 Relative Humidity ........................................................................................................................................... 5 2.1.3 Altitude ............................................................................................................................................................. 5
2.2 Transportation .............................................................................................................................5 2.2.1 Vibration Test (Package, Non-Operating)................................................................................................... 5 2.2.2 Drop Test (Package, Non-Operating) .......................................................................................................... 6 2.2.3 Vibration Test (Unpackaged, Non-Operating) ........................................................................................... 7 2.2.4 HALF-SINE SHOCK ..................................................................................................................................... 7
2.3 Packing Configuration ................................................................................................................7 2.3.1 Container Specification .................................................................................................................................. 7 2.3.2 Carton Specification ....................................................................................................................................... 8 2.3.3 Pallet Specification ......................................................................................................................................... 8 2.3.4 Container Carrying Capacity ......................................................................................................................... 8
2.4 Electrostatic Discharge Requirements.......................................................................................9 2.5 Safety Requirements....................................................................................................................9 2.6 EMI Requirements ......................................................................................................................9 2.7 Reliability......................................................................................................................................9 2.8 Mechanical Design for TCO 99: .................................................................................................9 2.9 Environment Protection Design: ................................................................................................10 2.10 Acoustical Noise .........................................................................................................................10
3. Input / Output Signal Specification .......................................................................................10 3.1 Input Signal Requirements .........................................................................................................10 3.1.1 Signal cable (Directly attached to unit) ....................................................................................................... 10 3.1.2 Video signals: .................................................................................................................................................. 10 3.1.3 Sync signal:...................................................................................................................................................... 10
3.2 Function ........................................................................................................................................11 3.2.1 Support timing ................................................................................................................................................. 11
3.3 Number of display colors: ...........................................................................................................12 3.4 Adjustment function ....................................................................................................................12 3.5 Power Supply Requirements.......................................................................................................12 3.5.1 Input Power Requirements ............................................................................................................................ 12 3.5.2 Output Power Requirement ........................................................................................................................... 13 1
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification Table of Contents 3.5.3 Power Management ........................................................................................................................................ 13
3.6
Specification of Inverter ...........................................................................................................13
3.7 Panel optical Characteristics ......................................................................................................14
4. Functional specification .............................................................................................................16 4.1 Display Quality.............................................................................................................................16 4.1.1 Display Data Area (with full white pattern) ................................................................................................ 16 4.1.2 Video Performance ......................................................................................................................................... 16 4.1.3 Light Output .................................................................................................................................................... 16 4.1.4 Brightness Adjustment Range ....................................................................................................................... 16
5. Physical Specifications................................................................................................................17 5.1 Physical Dimension & Appearance ............................................................................................17 5.1.1 Overall Dimensions: ....................................................................................................................................... 17 5.1.2 Outer Appearance: .......................................................................................................................................... 17
5.2 Construction and Materials on outer surface ...........................................................................17 5.3 Base ...............................................................................................................................................17 5.4 Marking & Labels........................................................................................................................17 5.4.1 Reference Label (Rear panel)........................................................................................................................ 17 5.4.2 Controls & Connectors................................................................................................................................... 17
5.5 Packaging......................................................................................................................................17 5.5.1 Carton Dimension: .......................................................................................................................................... 17 5.5.2 Shipping Weight: ............................................................................................................................................ 17 5.5.3 Shipping Container: ........................................................................................................................................ 17
6. Maintainability Specifications .................................................................................................17 6.1 General & Requirements ............................................................................................................17 6.1.1 Installation: ...................................................................................................................................................... 17 6.1.2 Periodic Maintenance: .................................................................................................................................... 17 6.1.3 Repair & Calibration: ..................................................................................................................................... 17
6.2 Mean Time to Repair...................................................................................................................17 6.2.1 Module Level: ................................................................................................................................................. 17 6.2.2 Component Level: .......................................................................................................................................... 17
6.3 Accessibility ..................................................................................................................................17 6.3.1 General: ............................................................................................................................................................ 17 6.3.2 Outside Cabinet, access to the following elements .................................................................................... 18 6.3.3 Cover Removal, Access ................................................................................................................................. 18
6.4 Equipment & Tools Required.....................................................................................................18 6.4.1 Standard Test Equipment ............................................................................................................................... 18 6.4.2 Documentation ................................................................................................................................................ 18
2
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification Table of Contents
6.5 Electrical Emission and Energy Saving summary for TCO99 ................................................18 6.5.1 Electrical Field(AC): ...................................................................................................................................... 18 6.5.2 Magnetic Field(AC): ...................................................................................................................................... 18 6.5.3 Energy Saving: ................................................................................................................................................ 18
Appendix 1 – Shipment Conditions..................................................................................................18 Fig. 1
Physical Dimension Front View and Side view .................................................................19
3
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification 1. Introduction
This specification describes a 17.0” color TFT LCD monitor which is supported by analog interface solution and support maximum resolution 1280x1024 at 76 Hz refresh rate. It has the following features: - User controls: (a) “Power on/off” switch. (b) “Exit” key( Back to main menus or leave OSD menu). (c) “I-key”( For auto adjust vertical position, phase, horizontal position and pixel clock ). (d) “Enter” key(For enter sub-menus or select items. And hot key lock / unlock mode). (e) “Left” key (Select left, decreasing adjust and hot key of Contrast mode). (f) “Right” key (Select right, increasing adjust and hot key of Brightness mode). - OSD window for control and information display with 8 languages selection. - DPMS (Display Power Management System) - Power on/off indicator. - High quality advanced zoom function (Scaling function) - Tilt base : Attached base with 0~25 degree tilt. -DDC2B function supported. - A LCD monitor (a)Head part: (1) A LCD module(CPT 170EA03). (2) An AC power and inverter board. (3) An Interface board. (4) A control board. (5) A 15pin D-sub connector .
(b) Base part: (1) Tilt base. (2)Foldable - A power cord - An user menu. -Setup disk. (including .INF/.ICM/Test pattern) --all INF/ICM/Test pattern are loaded in CD manual + Quick start guide
4
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification 2. Operational Specification 2.1 Environment
2.1.1 Temperature 0 to 40 oC -20 to 60 oC
-Operating -Storage
2.1.2 Relative Humidity -Operating -Storage
10 to 90% Max. ( non-condensing) 10 to 95% Max. ( non-condensing)
2.1.3 Altitude -Operating -Storage
0 to 3,048m (10,000ft) 0 to 12,192m (40,000ft)
2.2 Transportation 2.2.1 Vibration Test (Package, Non-Operating) A) Sine-wave vibration for initial resonance sweeps and dwell * Sine sweep Frequency (Hz) 5 ~ 26.6 26.6 ~ 50 50 ~ 500
Status 0.6G 0.016" 1.5G
Sweep times: 1 sweep / Per Axis (X,Y, and Z Axis ) * One major resonance dwell is required for each axis. Total dwell time at each resonance point shall be 15 minutes. B) Random Vibration Frequency (Hz) Slope ( dB/Oct.) Spectrum Level (g2/Hz) 0 0.015 5 ~ 100 -6 --100 ~ 200 200 --0.0038 Equivalent to 1.47 G rms * Duration: 30 Minutes / Per Axis (X,Y, and Z Axis ) Total test time : 90 Minutes
5
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification
2.2.2 Drop Test (Package, Non-Operating) A) Drop Height
Weight ( Kg )
ACM Spec. Height (cm)
0–9 > 9 - 18.2 > 18.2 - 27.2 > 27.2 - 45.4 > 45.4 - 68.1 > 68.1 – 113.5
91 76 61 46 31 26
Upgrade one level of height before MP. B)
Drop Sequence 6
1 Surface
1. Top 2. Front 3. Bottom 4. Rear 5. Right 6. Left
2 4
Manufacturing joint 5
3
-Corner 5-3-2 select
at weakness side [the low left(or right) corner of the front panel] -An edge drop with impact on the shortest edge radiating from corner 5-3-2 -An edge drop with impact on the next shortest edge radiating from corner 5-3-2 -An edge drop with impact on the longest edge radiating from corner 5-3-2 -A flat drop with impact on the rear -A flat drop with impact on the front -A flat drop with impact on the right -A flat drop with impact on the left -A flat drop with impact on the bottom -A flat drop with impact on the top After test, there is no electrical and mechanical damage permitted.
6
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification
2.2.3 Vibration Test (Unpackaged, Non-Operating) 5~200Hz at 1.04g rms FREQUENCY (Hz)
SPECTRUM LEVEL (g2/Hz)
2.0 4.0 8.0 40.0 55.0 70.0 200.0
0.0185 0.0300 0.0300 0.0030 0.0100 0.0100 0.0010
DURATION: 15 MINUTES PER AXIS.
2.2.4 HALF-SINE SHOCK
Test conditions: Test unit : 2 sets Each unit has to withstand 18 shocks.(3 shocks pre face) No- operation Half-sine wave Duration : 3ms Acceleration(G) : 75G
2.3 Packing Configuration 2.3.1 Container Specification a. Shipping Container 20'*8'*8'6 " Steel
Container Type
40'*8'*8'6" Steel
40'*8'*9'6" High Cube Steel
Weight (Kegs)
Interior Measurement (mm)
Gross
24,000
30,480
30,480
Tare
2,370
4,000
4,200
Payload
21,630
26,480
26,280
Length
5,898
12,031
12,031
Width
2,352
2,352
2,352
Height
2,394
2,394
2,699
33.2
67.74
76.4
Width
2,340
2,340
2,340
Height
2,280
2,280
2,585
Length
5,890
12,000
12,000
Width
2,330
2,330
2,330
Height
2,100
2,100
2,405
Volume (Cubic Meter) Door opening (mm) Useable Interior Dimension (Deducted pallet (130mm & Operating space 50mm) b. Air Transport Container Type Gross
Container (1)
Container (2)
Container (3)
125"*96"*96"
125"*96"*118"
125"*88"*64"
6,804
6,804
4,627
7
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification Weight (Kegs)
Interior Measurement (mm)
Tare
129
129
129
Payload
6,675
6,675
4,498
Length
3,048
3,048
3,048
Width
2,260
2,260
2,082
Height
2,438
2,997
1,625
17
19
11
Volume (Cubic Meter)
2.3.2 Carton Specification Product
Net
4.2
Weight (Kegs)
Gross
6.2
Length
368
Width
407
Height
140
Length
385
Width
445
Height
147
Carton Interior Measurement (mm)
Carton External Measurement (mm)
2.3.3 Pallet Specification a. Dimension Transport Type Shipping Pallet Dimension (mm)
Air Transport Pallet Dimension (mm)
Pallet A
Pallet B
Pallet C
Length
770
770
Width
890
1335
890
1335
Height
115
115
115
115
Length
X
X
X
X
Width
X
X
X
X
Height
X
X
X
X
Pallet D 1155
1155
2.3.4 Container Carrying Capacity a. Shipping Container Stowing Type
20'
Quantity of products (sets)
Quantity of Products (sets)
Quantity of pallet (sets)
(Every container)
(Every Pallet)
(Every Container)
1050
with pallet 40'
2100
Pallet A: 56
Pallet A: 6
Pallet B:
Pallet B:
6
Pallet C:84
Pallet C:
1
Pallet D:126
Pallet D: 1
Pallet A: 56
Pallet A: 15
Pallet B:
Pallet B: 15
84
84
8
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification 2.4 Electrostatic Discharge Requirements The subject product must withstand 8 KV for contact discharge and 15 KV for air discharge of Electrostatic Discharge and meet the acceptance criteria as specified IEC 801-2 .
2.5 Safety Requirements The display unit complies with the following safety standards and specifications. -UL compliance....standard for information-processing and business equipment, UL 1950. -CSA compliance...standard C22.2 No. 950-M89, data processing equipment. -TUV compliance...EN60950 safety specification-business equipment. -ISO13406-2 .Ergonomic Requirements of Visual Display. -Demko...EN60950. -Nemko...EN60950. -Semko...EN60950. -Fimko...EN60950.
2.6 EMI Requirements 1. This display unit complies with the following EMC rules and regulations. -FCC compliance...FCC Rule, Part 15, Subpart B, Class B. -VCCI compliance...VCCI Rule, Class-2. -CE Mark Compliance... 89/336/EEC. EN55024, EN61000-4-2/-3/-4/-5/-6/-8/-11 EN55022, Class B. EN61000-3-2,EN61000-3-3. -DNSF compliance...EN55022, Class B. -MPR2 compliance - TCO99 -C-Tick -BSMI -EPA 2. The sample for EMI agency approval should be under 4 dB of the limit. The production pilot run units should be under 3 dB of the limit. The mass production units should be under 1 dB of the limit.
2.7 Reliability 1. The prediction MTBF of display unit shall be greater than 60,000 hours excluding the lamp.(at 25 ℃) 2. Lamp life time : 40,000 hrs typical at which brightness of lamp is 50% compare to that of initial value at 7.0mA and 25℃.
2.8 Mechanical Design for TCO 99: 1) Front Frame Reflectance: * diffuse reflectance: > 20% * Gloss 25g shall be marked in accordance with ISO11469 3) Variety of Plastic: All plastic components that weight > 100g shall be made from the same type of plastic. 4) Painting of Plastic: *Any plastic components that weight >100g shall not be painted lacquer or vanished, so that the paint, lacquer or vanish in dry matter exceed 1 weight-% of the plastic component. * Mould decoration (IMD) is not allowed * All paints, lacquers, vanishes or colour additives used shall be declared by the type and mount.
9
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification 5) Metallization of Plastic Housing: * Metallization is not allowed. 6) Plastic components
> 25g shall not contain retardants of organically bound chloride or bromide.
2.9 Environment Protection Design: Product is Per ES 715-c49 Environment Design Guide
2.10 Acoustical Noise
With the display operating, the issue of sound measured is contained within 40 dB/A in the audible field.
3. Input / Output Signal Specification 3.1 Input Signal Requirements 3.1.1 Signal cable (Directly attached to unit) 3.1.1.1 Video Inputs: (1) DSUB –digital Signal Inputs 15pin D-sub connector is on the captive signal cable for IBM VGA, compatible graphic adapters. The pin assignment of this connector is described as below: 5 10 15
1 6 11
15pin D-sub female 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
RED VIDEO GREEN VIDEO BLUE VIDEO GROUND GROUND RED GROUND GREEN GROUND BLUE GROUND PC5V SYNC GROUND GROUND SDA H SYNC (H+V) V SYNC SCL
3.1.1.2 Cable length: 1600mm +/-
20mm
3.1.2 Video signals: RGB separate, Analog 0.7Vp-p/75 Ohm
3.1.3 Sync signal: - H/V separate, TTL level - H/V composite, TTL level
10
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification 3.2 Function 3.2.1 Support timing This Interface board is designed to operate in any of the following video mode. Incoming display mode (Input timing) Resolution
Multi-scan operation
Horizontal Vertical Dot Clock Remark Frequency (KHz) Frequency (Hz) Frequency (MHz)
640x350
31.47(P)
70.08(N)
25.17
DOS
720x400
31.47(N)
70.08(P)
28.32
DOS
640x480
31.47(N)
60.00(N)
25.18
DOS
640x480
35.00(N)
67.00(N)
30.24
Macintosh
640x480
37.86(N)
72.80(N)
31.5
VESA
640x480
37.50(N)
75.00(N)
31.5
VESA
800x600
37.88(P)
60.32(P)
40.00
VESA
800x600
48.08(P)
72.19(P)
50.00
VESA
800x600
46.86(P)
75.00(P)
49.50
VESA
832X624
49.72(N)
74.55(N)
57.29
Macintosh
1024x768
48.36(N)
60.00(N)
65.00
VESA
1024x768
56.48(N)
70.10(N)
75.00
VESA
1024x768
60.02(P)
75.00(P)
78.75
VESA
1024X768
60.24(N)
74.93(N)
80.00
Macintosh
1152x864
67.50(P)
75.00(P)
108.00
VESA
1152x870
68.68(N)
75.06(N)
100.00
Macintosh
1152x900
61.80(N)
66.00(N)
94.50
SUN 66
1152x900
71.81(N)
76.14(N)
108.00
SUN
1280x1024
64.00(P)
60.00(P)
108.00
VESA
1280x1024
75.83(N)
71.53(N)
128.00
IBM1
1280x1024
80.00(P)
75.00(P)
135.00
VESA
1280x1024
81.18(N)
76.16(N)
135.09
SPARC2
Actual display resolution 1280x943
full screen 1280x1024
11
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification Notes: (1) If the incoming display mode is not supported by this I/F board listed above, the picture can show up or doesn’t which is unpredictable, even the picture can display but probably isn’t good or clear. (2) Some signals from graphics board may not function properly. (3) “P”, “N” stands for “Positive”, “Negative” polarity of incoming HSYNC/VSYNC(input timing). (4) OSD will show “No Signal” message on the screen as below to indicate it while no display mode inputs. (5) OSD will show “Out of Range” message on the screen to indicate it while input display mode meet the following condition (a) The resolution is large than 1280x1024. (b) The resolution is 1280x1024 but it frequency of vertical sync (Fv) is large than 77Hz. (c) The frequency of horizontal sync (Fh) is large than 82KHz. (d) The frequency of vertical sync (Fv) is large than 76Hz.
3.3 Number of display colors: 16M color numbers (With Dithering)
3.4 Adjustment function
Brightness Contrast Display position (Vertical , Horizontal) Phase Pixel clock Color gain(Red, Green, Blue) OSD position (Vertical , Horizontal) Multi-language selection OSD time Recall function(Position Recall、Color Recall、Recall All)
3.5 Power Supply Requirements 3.5.1 Input Power Requirements (1) Input Voltage Range
The unit shall meet all the operating requirements with an input voltage range of 90~264 Vac . (2) Input Current Maximum Input Current (MAX) 2 Arms
Measuring Range 90Vac 〜 264Vac
(3) Frequency Range The unit shall operate within a frequency range of 47Hz to 63Hz. (4) Inrush Current Power supply inrush current shall be less than the ratings of its critical components(including Power switch, fuse, rectifiers and surge limiting device) for all conditions of line voltage. (5) Regulator Efficiency 70% minimum (measuring at 115Vac and full load) Power saving mode < 1 Watts
12
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification
3.5.2 Output Power Requirement The power circuit shall supply DC power outputs as followings: Output
Nominal
Regulation
Load Current Range
1
12V-panel
±10%
0 ~ 0.25A
2
3.3V-panel
±10%
0 ~ 0.1A
3
3.3V-Fix
±5%
0 ~ 1.0A
3.5.3 Power Management Mode
H/Vsync
Power consumption
Normal
Both exist
< 40W
off
None or Only one exist
< 1W
LED Color (Status) Green (Normal)
Recovery Time
Amber
5 sec
--
3.6 Specification of Inverter The backlight system is an edge-lighting type with 4 CCFLs (Cold Cathode Fluorescent Tube). The characters of dual lamps are shown in the following tables.
ITEM
Lamp Voltage
SYMBOL VL
IL
Lamp Current Inverter Frequency
FL
Starting lamp voltage
VS
Lamp life time
LT
MIN --
TYP 710
10 45
--
MAX --
Unit V
14 50 ---
16 70 1350 1080
mA kHz V V
50,000 (40,000)
--
Hr
Condition IL=7.0 mA Each connector Tb=0 oC Ta=25oC IL = 6.0mA Continuous Operation (IL=7.0 mA)
NOTE: 1.All condition are at 25C ambient unless otherwise specified. 2. Load Panel=SXGA 17”
13
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification
3.7 Panel optical Characteristics Item
Condition
Symbol
Min.
Typ.
Max.
Unit
Contrast Ratio
ψ=0°,θ=0°
CR
360
450
--
--
Vertical Up Down
ψ=0° ψ=0°
(CR>=10) (CR>=10)
θ θ
-55~55 -55~55
-65~65 -65~65
---
Deg. Deg.
Horizontal Left Right
θ=0° θ=0°
(CR>=10) (CR>=10)
ψ ψ
-60~60 -60~60
-70~70 -70~70
--
Deg. Deg.
25±2.5° ψ=0°,θ=0°
Tr Tf
---
---
9 16
---
ms ms
ψ=0°,θ=0°
Tr+Tf
--
--
25
--
ms
White Luminance
Center point at CCFL 7.0mA
--
240
300
--
cd/m²
Brightness Uniformity
θ=ψ=0°
--
70
--
--
%
Crosstalk
θ=ψ=0°
CMR
--
--
1
%
0.607 0.314 0.280 0.552 0.113 0.070 0.283 0.299
0.637 0.344 0.310 0.582 0.143 0.100 0.313 0.329
0.667 0.374 0.340 0.612 0.173 0.130 0.343 0.359
Viewing Angle
Response Time Rise Time Fall Time Cross Talk
Red Chromaticity
x y Green x y Blue x y White x y
ψ=0°,θ=0°
--
Note: 1. Viewing Angle, Contrast Ratio, Response Time, Reflectance, and Chromaticity are measured at panel center. 2. Viewing Angle(θ, ψ) Measurement is done on position 1. Viewing angle origine is the axis normal to the flat panel. Left (L) and Right (R) value are the maximum angles for which CR=10. Up (U) and (D) value are the maximum angles for which CR=10. See figure below
Normal E y È Ö = 180 , Left
Ö
Ö = 90 , Up x Ö = 0 , Right
Ö = 270 , Down
14
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification
3.Contrast Ratio (CR) is defined mathematically as: Luminance in White Level (Max.) Luminance in Black Level (Min.) o
o
(at θ = 0 , φ = 0 )
4. Response time TrR measures the transition time of L1 relative luminance from white to black state, from 90% to 10% (see graph below) TrD measures the transition time of L1 relative luminance from black to white state, from 10% to 90% (see graph below) BLACK
WHITE
WHITE
100% 90%
10% 0%
t TrR
TrD
5. Cross talk shall be measured between two patterns. 1/2
1/6
2/3
1/2
1/3 1/6
FULL WHITE A
1/6
A' B'
B
184 gray level
184 gray level
1/3 1/2 2/3
0 gray level
l LA-LA’ l / LA x 100%= 1.2% max., LA and LB are brightness at location A and B l LB-LB’ l / LB x 100%= 1.2% max., LA’ and LB’ are brightness at location A’ and B’ LA:Luminance of measured point in A (cd/m2) LB:Luminance of measured point in B (cd/m2) LA’:Luminance of measured point in A’ (cd/m2) LB’:Luminance of measured point in B’ (cd/m2) o
(at Viewing Angle θ = 0 ,φ = 0 ) o
15
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification 6. Brightness Uniformity of these 9 points is defined as below: 1
2
3
4
5
6
7
8
9
90%
Brightness Uniformity
=
50% 90%
50%
Min. brightness
10%
10%
/ Max. brightness x 100 % > 70%
4. Functional specification
All the tests to verify specifications in this section must be performed under the following standard conditions unless otherwise noted. The standard conditions are: -Temperature : 0 to 40 degree Celsius -AC line input voltage : 90 Vac to 264 Vac, 47Hz or 63Hz -Warm-up time : 30 minutes minimum
4.1 Display Quality 4.1.1 Display Data Area (with full white pattern) (1) Horizontal: 337.920 mm (2) Vertical: 270.336 mm
4.1.2 Video Performance (1) Resolution : 1280 X 1024 pixels Maximum (2) Contrast ratio : 360(Min.), 450(Typ.) (3) Response time : 25 mS(Typ.) (4)Viewing angle : Up:65° Down:65° R/L:70° (At contrast ratio >= 10) (5)CIE Coordinate: White ( 0.313, 0.329 ) +/- (0.03, 0.03) (at user mode) (6) Display color: 18 bits color
4.1.3 Light Output Brightness rating : 300cd/㎡(Typ.) @7.0mA
4.1.4 Brightness Adjustment Range At contrast ratio control set at maximum level, adjusting Brightness control from minimum to maximum position, the light output of WHITE pattern shall be increased more than 40cd/㎡.
16
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification 5. Physical Specifications
5.1 Physical Dimension & Appearance 5.1.1 Overall Dimensions: 375mm (W) X 370mm (H) X 155mm (D)
5.1.2 Outer Appearance: see Fig.1
5.2 Construction and Materials on outer surface (1) Materials: Plastic (2) Color: To be defined for Model
5.3 Base (1)Tilt:
fiest hinge:0°~ 25° , second hinge : 25 °~135°
5.4 Marking & Labels 5.4.1 Reference Label (Rear panel) (1) Reference numbers (2) Manufacture data (3) Agency Approvals (4) Power Ratings
5.4.2 Controls & Connectors (1) AC power cord input: abbreviated labels (2) User's Controls: standard print
5.5 Packaging 5.5.1 Carton Dimension: 385mm (W) X455mm (D) X 1478mm (H) (LCD monitor)
5.5.2 Shipping Weight: 6.2kg (LCD monitor) 5.5.3 Shipping Container:
2100 sets per 40 feet container with pallet.
6. Maintainability Specifications 6.1 General & Requirements 6.1.1 Installation: From outside of unit with standard tools and documentation provided to user.
6.1.2 Periodic Maintenance:
No periodic maintenance is required.
6.1.3 Repair & Calibration:
Require spare modules or components as specified as followings: (1) Interface board ASSY (2) AC-DC converter board ASSY (3) Control board ASSY
6.2 Mean Time to Repair 6.2.1 Module Level: Less than 10 minutes
6.2.2 Component Level:
Less than 15 minutes
6.3 Accessibility 6.3.1 General: All panels, covers, and major assemblies are removable without disruption of permanent mounting or fasteners.
17
Q7T3(CPT panel) LCD Monitor Service Guide Engineering Specification
6.3.2 Outside Cabinet, access to the following elements -Operating Controls -AC Inlet -Audio in
6.3.3 Cover Removal, Access All sub assemblies and internally adjustable components may be accessed by removing the base and the rear cover .
6.4 Equipment & Tools Required 6.4.1 Standard Test Equipment (1) Voltmeter (2) Dual trace oscilloscope (3) Hand tools as required (4) Computer with IBM VGA , or compatible graphic adapter
6.4.2 Documentation in
A service manual will be available which covers all service requirements. A users manual written Japanese German, Italian, Spanish, France and English will be available to ship with the product.
6.5 Electrical Emission and Energy Saving summary for TCO99 6.5.1 Electrical Field(AC): *Band I< 10V/m (132cd/m^2,”+” pattern) *Band II< 1V/m (132cd/m^2,”+” pattern) Note: Shielded power cord is not acceptable
6.5.2 Magnetic Field(AC): *Band I< 200nt (132cd/m^2,”+” pattern) *Band II< 32nt (132cd/m^2,”+” pattern) Note: Shielded power cord is not acceptable
6.5.3 Energy Saving:
*1st stage:
View more...
Comments