Fluent Meshing Migration Manual
ANSYS, Inc. Southpointe 2600 ANSYS Drive Canonsburg, PA 15317
[email protected] http://www.ansys.com (T) 724-746-3304 (F) 724-514-9494
Release 18.0 January 2017 ANSYS, Inc. and ANSYS Europe, Ltd. are UL registered ISO 9001: 2008 companies.
Copyright and Trademark Information © 2016 SAS IP, Inc. Unauthorized use, distribution or duplication is prohibited. ANSYS, ANSYS Workbench, Ansoft, AUTODYN, EKM, Engineering Knowledge Manager, CFX, FLUENT, HFSS, AIM and any and all ANSYS, Inc. brand, product, service and feature names, logos and slogans are registered trademarks or trademarks of ANSYS, Inc. or its subsidiaries in the United States or other countries. ICEM CFD is a trademark used by ANSYS, Inc. under license. CFX is a trademark of Sony Corporation in Japan. All other brand, product, service and feature names or trademarks are the property of their respective owners.
Disclaimer Notice THIS ANSYS SOFTWARE PRODUCT AND PROGRAM DOCUMENTATION INCLUDE TRADE SECRETS AND ARE CONFIDENTIAL AND PROPRIETARY PRODUCTS OF ANSYS, INC., ITS SUBSIDIARIES, OR LICENSORS. The software products and documentation are furnished by ANSYS, Inc., its subsidiaries, or affiliates under a software license agreement that contains provisions concerning non-disclosure, copying, length and nature of use, compliance with exporting laws, warranties, disclaimers, limitations of liability, and remedies, and other provisions. The software products and documentation may be used, disclosed, transferred, or copied only in accordance with the terms and conditions of that software license agreement. ANSYS, Inc. and ANSYS Europe, Ltd. are UL registered ISO 9001: 2008 companies.
U.S. Government Rights For U.S. Government users, except as specifically granted by the ANSYS, Inc. software license agreement, the use, duplication, or disclosure by the United States Government is subject to restrictions stated in the ANSYS, Inc. software license agreement and FAR 12.212 (for non-DOD licenses).
Third-Party Software See the legal information in the product help files for the complete Legal Notice for ANSYS proprietary software and third-party software. If you are unable to access the Legal Notice, Contact ANSYS, Inc. Published in the U.S.A.
Table of Contents 1. Migrating to Fluent Meshing 18.0 .......................................................................................................... 1 1.1. The Contents of This Manual ............................................................................................................. 1 1.2. Additional Resources ........................................................................................................................ 1 2. Feature Changes in Fluent Meshing 18.0 ................................................................................................ 3 2.1. Changes in Product Behavior from Previous Releases ......................................................................... 3 2.2. Added Features ................................................................................................................................ 3 3. Text Command List Changes in Fluent Meshing 18.0 ............................................................................. 5 3.1. Modified Fluent Meshing Text Commands ......................................................................................... 5 3.2. New Fluent Meshing Text Commands ................................................................................................ 5
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
iii
iv
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
Chapter 1: Migrating to Fluent Meshing 18.0 The purpose of the Fluent Meshing Migration Manual is to help you transition to the most recent version of ANSYS Fluent Meshing. Read through the entire document to understand the changes that have taken place. 1.1.The Contents of This Manual 1.2. Additional Resources
1.1. The Contents of This Manual This version of the Fluent Meshing Migration Manual highlights changes between Fluent Meshing 17.2 and Fluent Meshing 18.0. This document will include a brief description of new features and changes in text command settings. The information is enclosed in the following chapters: • Feature Changes in Fluent Meshing 18.0 (p. 3) • Text Command List Changes in Fluent Meshing 18.0 (p. 5) If you are upgrading across several releases, you may find it helpful to consult technical support for assistance.
1.2. Additional Resources For a complete list of Fluent manuals, see The Contents of the Fluent Manuals. To access documentation files on the ANSYS Customer Portal, go to http://support.ansys.com/documentation. Here you can also find Release Notes and a list of Known Issues and Limitations. Expand the General category to access these documents For a list of platform/OS levels that are supported in the current release, visit the ANSYS website. Please note that beta features have not been fully tested and validated. ANSYS, Inc. makes no commitment to resolve defects reported against these prototype features. Changes in behavior are sometimes expected and are not captured in this document. However, if there are differences between the Release 16.X beta features and the Release 18.0 standard Fluent Meshing features that concern you, contact technical support for assistance. Your feedback is appreciated and will help us improve the overall quality of the product.
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
1
2
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
Chapter 2: Feature Changes in Fluent Meshing 18.0 Several features have been improved or added in Fluent Meshing Release 18.0. The following sections describe such feature changes: 2.1. Changes in Product Behavior from Previous Releases 2.2. Added Features
2.1. Changes in Product Behavior from Previous Releases • Interior zones between different cell zones will no longer be automatically converted to internal type when the mesh/case file is read. • The file size and time taken for writing case files in the Hierarchical Data Format (HDF) should be significantly reduced due to a change in the default compression level. • Domains are now updated to include new zones after face zones are remeshed and replaced. • The option for creating intersection loops for marked cross-object intersections has been changed to create only cross-object intersection loops.
2.2. Added Features The new features available in the meshing mode in Fluent include enhancements to existing features, and improved robustness through defect fixes. The following enhancements have been made: • Dialog boxes containing lists are expandable. • An octree option has been added for hexcore cell generation. This option will result in faster hexcore mesh generation but does not support hexcore generation up to boundaries. • The Inverse Orthogonal Quality measure has been added. • New scripting commands are available for marking faces; improving and remeshing boundary faces; and connecting overlapped face zones.
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
3
4
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
Chapter 3: Text Command List Changes in Fluent Meshing 18.0 Changes to the text command lists are classified as either Modified or New; where a modified command refers to either a changed behavior or a deleted command, and a new command is one that did not exist in previous versions of Fluent Meshing. Details of the text command list changes are tabulated in the following pages: 3.1. Modified Fluent Meshing Text Commands 3.2. New Fluent Meshing Text Commands
3.1. Modified Fluent Meshing Text Commands Modified text commands appear in the following tables, grouped according by menu. • Table 3.1: Modified Text Commands/Settings for the file/ Menu (p. 5) • Table 3.2: Modified Text Commands/Settings for the report/ Menu (p. 5) Table 3.1: Modified Text Commands/Settings for the file/ Menu Text Command
Modified Command or Setting
/file/read-multiple-case
This command has been removed.
Table 3.2: Modified Text Commands/Settings for the report/ Menu Text Command
Modified Command or Setting
/report/quality-method
The inverse-ortho-quality method has been added.
3.2. New Fluent Meshing Text Commands Text commands added in the latest release of Fluent Meshing appear in the following tables, grouped according by menu. • Table 3.3: New Text Commands for the mesh/ Menu (p. 5) Table 3.3: New Text Commands for the mesh/ Menu Text Command /mesh/hexcore/controls/octree-hexcore?
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
5
6
Release 18.0 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential information of ANSYS, Inc. and its subsidiaries and affiliates.
