ansi.b36.10.pdf

By Authority Of THE UNITED STATES OF AMERICA

Legally Binding Document By the Authority Vested By Part 5 of the United States Code § 552(a) and Part 1 of the Code of Regulations § 51 the attached document has been duly INCORPORATED BY REFERENCE and shall be considered legally binding upon all citizens and residents of the United States of America. HEED THIS NOTICE: Criminal penalties may apply for noncompliance.

e Document Name: CFR Section(s): Standards Body:

ANSI B36.19: Welded and Seamless Wrought Steel Pipe 24 CFR 3280.705(b)(1) American National Standards Institute

Official Incorporator: THE EXECUTIVE DIRECTOR

OFFICE OF THE FEDERAL REGISTER WASHINGTON, D.C.

AMERICAN NATIONAL STANDARD FOR WELDED AND SEAMLESS WROUGHT STEEL PIPE (ANSI 836.10.. 1979)1

FOREWORD In March, 1927, the American Standards Association authorized the organization of a Sectional Commit· tee on Standardization of Dimensions aizd Material of Wrought Steel and Wrought Iron Pipe and Tubing, for the purpose of unifying the standards of these commodities in force in this country. The American Society for Testing and Materials and The American Society of Mechanical Engineers were designated as sponsors and the first meeting of the sectional committee was held in Pittsburgh, Pa., on May 18,1928. The dimensions of commercial pipe, in general use in the United States at the time, conformed rather generally to, those recommended by the ASME Committee on Standard Pipe and Pipe Threads, published in 1886 (ASME Trans., vol. VIII, page 29). On these standards an enormous industry has been built and the satisfactory use of this product proves the soundness of the original design and specification. Increa:singly severe service demands at the time of the committee's organization, had been met by using the nearest available pipe or tubing for heavier secfions, such as casing, mechanical tubing, etc., with result· ing uneconomical multiplicity of wall thicknesses. Subsequently; the committee, with the cooperation of the industry, made a survey of existing practice as the logical statting point for the development of an American Standard. From this survey, a Table was designed to provide a selection of wall thicknesses of pipe to cover the power piping requirements of industry where strength to resist internal pressure governs selection and was later expanded to include pipe diameters and thicknesses used in other industries. The original intent of the Committe.e was to establish a system of Schedule Numbers for pipe size/wall combinations which would have an approximately uniform relationship equal to 1000 times the PIS expres· sion contained in the modified Barlow formula for pipe wall thickness as defined in the Appendix to this standard. The resulting Numbers departed so far from existing wall tllicknesses in common use that the original intent could not be accOlilplished. The Scheoule Numbers were th'E:n adopted strictly as a convenient designation system for use in ordering. In all cases, the designer must base his selection on the rules and allowable stresses set by the code which goverIls his particular construction. The table is dimensionally complete for all sizes and wall thicknesses within its scope, but some of the larger, heavier wall sections are beyond the capability of seamless mill production and must be obtained from forged and bored billets or other sources. The first issue, of this Standard was approved by letter ballot of the Sectional Committee in October 1934; by The American Society of Mechanic,al Engineers in November 1934, and by the AmericaIi Society for Testing and Materials in February 1935. Formal approval was given with the designation American Stan· dard' "tentative," by the American Standards Association, November 1935. Subsequent slight revisions to Table 1 and the footl\otes of the dimensional tables were approved in order by the Sectional Committee, the Sponsors, and the Am~rican Standards Association, The latter changed the designation to American Standard; date of approval April 28, 1939. Further revisions have been made by the Sectional Committee and approved by the Sponsors and the American Standards Association. The list of specifications in Table I has been revised where necessary and slight revisions in wall thicknesses of some of the large sizes of the heavy schedules have been made where PIS values were out of line. It was the hope in 1939 that the designations of pipe used commercially by all industry as standard weight, extra strong, and double extra strong would gradually be replaced by Schedule Number designation. However, owing to customs of over fifty years' standing, demand and production of pipe to these traditional dimensions is undiminished. Consequently. in response to a demand from users, accepted practice for dimensions and weights of commercial wrougllt steel and welded wrought iron pipe, were added. These changes in the Standard were approved by the Sectional Committee, the Sponsors, and the Amer· ican Standards Association, and it was designated an American Standard on February 23. 1950.

106.8

Subcommittee No.1 was reorganized in 1957 to revise and bring the Standard up to date. In addition to the necessary editorial.changes, a simplified format was selected for the tables of weights and dimensions so as to include and to identify the sizes and weights of API Standards 5L and 5 LX. The decimal wall thicknesses and plain end weights were established by a uniform procedure recognized by the tubular industry, and for some sizes the decimal wall thicknesses and plain end weights shown may vary slightly from those shown in the tables of previous issues of this Standard. These changes were approved by the Sectional Committee, the Sponsors, and the American Standards Association, and it was designated an American Standard on December 21,1959. This Standard was revised in 1969 to bring it up to date. A uniform method to calculate the plain end weight of steel pipe was included, and minor adjustments were made in the tabulated weights of steel pipe in Table 2 to conform to this new method. Additional sizes and thicknesses of steel pipe which have come into common use were also added to Table 2. Inasmuch as API Standard 5L no longer included wrought iron pipe, reference to this API Standard was deleted from Table 3. These changes in the Standard were approved by the Standards Committee, the Sponsors, and the American National Standards Institute, and it was designated an American National Standard on February 3, 1970. Further revisions were made .(0 this Standard in 1975. Additional sizes and thickness of steel pipe which had been added to API Specifications were added to Table 2. Table 3, Dimensions and Weights of Welded Wrought Iron Pipe was deleted in its entirety, since wrought iron pipe is no longer produced. These changes in the Standard were approved by the Standards Committee, the Secretariat, and the American National Standards Institute, and it was designated an American National Standard on June 5, 1975. .. This Standard was revised in 1978 to include SI metric dimensions. The outside diameter and wall thicknesses were converted to mm by multiplying the inch dimensions by 25.4. Outside diameters larger than 16" were rounded to' the nearest mm, and outside diameter 16" and smaller were rounded to the nearest 0.1 mm. Wall thicknesses were rounded to the nearest 0.01 mm. These converted and rounded SI metric dimensions were adde.d to Table 2.' A formula to calculate the SI metric plain end mass', kg/m, using SI metric diameters and thicknesses was adde.d to SectionS. TheSI metric plain end mass was calculated for each size and thickness, and was added to Table 2. These changes in the Standard were approved by the Standards Committee. the Secretariat, and the American National Standards Institute, and it was designed an American National Standard on July 18,1979 1

Reprinted by permission of the 'American Society of Mechanical Engineers, 345 East 47th St., New York, N.Y. 10017.

1069

ANSI 836.10-1979

AMERICAN NATIONAL STANDARD

WELDED AND SEAMLESS WROUGHT STEEL PIPE

1. SCOPE

5. WEIGHTS

This Standard covers the standardization of dimensions of welded and seamless wrought steel pipe, for high or low temperatures and pressures. The word pipe is used as distinguished from tube to apply to tubular products of dimimsions commoil1y used for pipelin.e and piping systems. Pipe dimensions of sizes 12 inch and smaller have ou'tside diameters numerically larger than corresponding sizes. In contrast, the outside diameters of tubes are numerically identical to the size number for all sizes.

The nominal weights of steel pipe are calculated values and are tabulated in Table 2. The nominal plain end weights, lbs./ft., are cal· culated using the following formula:

Wpe

= 10.68 (D - t) t

where

Wpe = nominal plain end weight rounded to the nearest 0.01 lb./ft. D

:1. SIZE The size of all pipe is iden tified by the nominal pipe size. The manufacture of pipe in the nominal sizes of 1/8 inch to 12 inches inclusive is based on a standardized outside diameter (OD). This OD was originally selected so that pipe with a standard OD and having a wall thickness which was typical of the period would have an inside diameter (ID) approximately equal to the nominal size. Although there is no such relation between the existing standard thickness-OD and nominal size-these nominal sizes and standard ODs continue in use as "standard." The manufacture of pipe in nominal sizes of 14 inch OD and larger. proceeds on the basis of an OD corresponding to the nominal size.

= outside

diameter to the nearest 0.001 in . . (The symbol D is to be used for 00 only in h1athematical equations or fomulas.)

= specified wall thickness rounded to the

nearesfD.OOl in: The nominal plain _end mass, kg/m, is calculated using the following formula:

Wpe

= 0.02466 (D - /) /

where

3. MATERIALS

The dimensional standards for pipe described here arc for products covered in the ASTM and API specifi· cations listed in Table 1.

4. WALL THICKNESS The nominal wall thicknesses are given in Table 2. Table 2 also indicates wall thicknesses listed in API Standards 5L, 5LX and 5LS.

1070

Wpe = nominal plain end mass rounded to the nearest 0.0 1 kg/m D

(0 the nearest 0.1 mm for outside diameters which are 16 in. and smaller and 1.0 mm for outside diameter larger than 16 in. (The symbol D is to be used for OD only in mathematical equations or formulas).

= outside diameter

specified wall thickness rounded to the ncarest 0.0 I mm.

6. PERMISSIBLE VARIATIONS Variations in dimensions differ depending upon the method of manufacture cmployed in maldng the pipe to the various specifications listed in Table 1. Permis' sible variations for dimensions are indicated in each specification.

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE 7. PIPE THREADS

Unless otherwise specified, the threads of threaded pipe shall conform to ANSI B2.l Pipe Threads (Ex· cept Drysea/).

ANSI 836.10-1979

Pipe'of sizes and wall thickness other than those of Standard, Extra·Strong, Double Extra Strong, and Schedule Number were adopted from API Standards 5L, 5LX and 5LS. It was not considered practical to establish Schedule Numbers nor new designations for them.

8. WALL THICKNESS DESIGNATIONS

The wall thickness designations "Standard", "Extra·Strong", and Double Extra·Strong" have been commercially used designations for many years. As ex· plained in the Foreword, the Schedule Numbers were subsequently added as a convenient designation for use in ordering pipe. Standard and Schedule 40 are iden· tical for nominal pipe sizes up to 10 inch inclusive. All larger sizes of Standard have 3/8 inch wall thickness. Extra·Strong and Schedule 80 are identical for nom· inal pipe sizes up to 8 inch inclusive. All larger sizes of Extra·Strong have 1/2 inch wall thickness.

/

1071

9. WALL THICKNESS SELECTION

When the selection of wall thickness depends primarily upon capacity to resist internal pressure under given conditions, the designer shall compute the exact value of wall thickness suitable for conditions for which the pipe is required as prescribed in detail in the ASME Boiler and Pressure Vessel Code, ANSI B3l Code for Pressure Piping, or other similar codes, whichever governs the construction. A thickness shall be selected from Table 2 to suit the value computed to fulflll the conditions for which the pipe is desired.

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10-1979

Table 1 Specifications for Pipe with ANSI Designations and Titles of Standard Specifications ASTM or Ap·1

Designation

ANSI Designation

Title

ASTM A53

8125.1

Welded and Seamless Steel Pipe

ASTM A106

8125.30

Seamless Carbon Steel Pipe for High-Temperature Service

ASTM A120

8125.2

81ack and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless Steel Pipe for Ordinary Uses

ASTM A134

8125.55

Electri~-Fusion (Arc)-Welded Steel Plate Pipe (Sizes 16 in. and Over)

ASTM A135

8125.3

Electric-Resistance-Welded Steel Pipe

ASTM A139

8125.31

Electric-Fusion (Arc)-Welded Steel Plate Pipe (Sizes 4 in. and Over)

ASTM A155

8125.4

Electric-Fusion-Welded Steel Pipe for High-Pressure Service

ASTM A211

8122.56

Spiral-Welded Steel or Iron Pipe

ASTM A312

8125.16

Seamless and Welded Austenitic Stainless Steel Pipe

ASTM A333

8125.17

Seamless and Welded Steel Pipe for Low·Temperature Service

ASTM A335

8125.24

Seamless Ferritic Alloy Steel Pipe for High-Temperature Service

ASTM A358

8125.57

Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe :or HighTemperature Service

ASTM A369

8125.27

Carbon and Ferritic Alloy Steel Forged and 80red Pipe for High-Temperature Service

ASTM A376

8125.25

Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service

ASTM A381

8125.35

Metal-Arc-Welded Steel Pipe for High-Pressure Transmission Systems

ASTM A405

8125.26

Seamless Ferritic Alloy Steel Pipe Specially Heat Treated for High·Temperature Service

ASTM A523

G62.5

Plain End Seamless and Electric-Resistance-Welded Steel P;pe for High Prec:;sure Pipe-Type Cable Circuits

ASTM A524

8125.37

Seamless Carbon Steel Pipe for Process Piping

ASTM A530

8125.20

General Requirements for Specialized Carbon and Alloy Steel Pipe

API 5L

Line Pipe

API5LX

High-Test Line Pipe

API5LS

Spiral Weld Line Pipe

1072

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10·1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe 51 Units

Inch Units Identification

Plain

Standard (STD) X·strong (X) XX·strong (XXS)

Plain Outside Diameter mm

Wall Thickness mm

End Mass kg/m

Inch Nominal

Outside Diameter

Wall Thickness

En,d Weight

Size

in.

in.

Ib/ft

'/. '/.

0.405 0.405

0.068 0.095

0.24 0.31

5L 5L

STD XS

40 80

10.3 10.3

1.73 2.41

0.37 0.47

Yo Yo

0.540 0.540

0.088 0.119

0.42 0.54

5L 5L

STD XS

40 80

13.7 13.7

2.24 3.02

0.63 0.80

'/. %

0.675 0.675

0.091 0.126

0.57 0.74

5L 5L

STD XS

40 80

17.1 17.1

2.31 3.20

0.84 1.10

y, y, y, y,

0.840 0.840 0.840 0.840

0.109 0.147 0.188 0.294

0.85 1.09 1.31 1.71

5L 5L

STD XS

40 80 160

5L

XXS

21.3 21.3 21.3 21.3

2.77 3.73 4.78 7.47

1.27 1.62 1.95 2.55

% %

1.050 1.050 1.050 1,050

0.113 0.154 0.219 0.308

1.13 1.47 1.94 2.44

5L 5L,

STD XS

40 80 160

5L

XXS

26.7 26.7 26.7 26.7

2.87 3.91 5.56 7.82

1.69 2.20 2.90 3.64

1.315 1.315 1.315 1.315

0.133 0.179 0.250 0.358

1.68 2.17 2.84 3.66

5L 5L

STD XS

40 80 160

5L

XXS

33.4 33.4 33.4 33.4

3.38 4.55 6.35 9.09

2.50 3.24 4.24 5.45

1% 1% 1%

1.660 1.660 1.660 1.660

0.140 0.191 0.250 0.382

2.27 3.00 3.76 5.21

5L 5L

STD XS

40 80 160

5L

XXS

42.2 42.2 42.2 42.2

3.56 4.85 6.35 9.70

3.39 4.47 5.61 7.77

1% 1% 1% 1%

1.900 1.900 1.900 1.900

0.145 0.200 0.281 0.400

2.72 3.63 4.86 6.41

5L 5L

STD XS

40 80 160

5L

XXS

48.3 48.3 48.3 48.3

3.68 5.08 7.14 10.15

4.05 5.41 7.25 9.56

2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375 2.375

0.083 0.109 0.125 0.141 0.154 0.172 0.188 0.218 0.250 0.281 0.344 0.436

2.03 2.64 3.00 3.36 3.65 4.05 4.39 5.02 5.67 6.28 7.46 9.03

5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX 5L5LX

60.3 . 60.3 60.3 60.3 60.3 60.3 60.3 60.3 60.3 60.3 60.3 60.3

2.11 2.77 3.18 3.58 '3.91 4.37 4.78 5.54 6.35 7.14 8.74 11.07

3.03 3.93 4.48 5.01 5.44 6.03 6.54 7.48 8.45 9.36 11.11 13.44

% %

1Y4

2 2

2 2 2

2 2 2 2 2

API Specs

5L5LX

'Schedule No.

STD

, . 40

XS

80

XXS

·N-Item not shown in ANSI 836.10-1975 which has been added to API Specifications. C-Corrected listing for an item that 'was incorrectly listed in ANSI 836.10-1975. No Code Letter-Item correctly listed in ANSI 836.10-1975.

1073

Previous Statu5

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE . .

ANSI 836:10-1979

Table,2 Dimensions arid Weights of Welded and Seamless Wrought Steel Pipe (Continued) Inch UnitS

81 Units Identification

Plain Incn

Outside

Wall

End

Nominal Size

Diameter in.

Thickness in.

Weight Ib/ft

0.083 0.109 0.125 0.141 0.156 0.172 0.188 0.203 0.216 0.250 0.276 0.375 0.552

2.47 3.22 3.67 4.12 4.53 4.97 5,40 5.79 6.13 7eOl 7.66 . 10.01 13.69

3.500 0.083 3 3 3.500 0.109 3.500 0.125 3 3.500 0.141 3 3.500 0.156 3 --:;3_ _ _-:3,:.;.5;.:0"'0_ _.,,0'-:.1"'72, 3 3.500 0.188 3 3.500 0.216 3 3.500 0.250 3.500 0.281 3 3.500 0.300 3.500 0,438 3 3.S00 0.600 3

3.03 3.95 4.51 5.06 5.57 6.11 6.65 7.58 8.68 9.66 10.25 14.32 18.58

2% 2% 2% 2% 2% 2~

2Ya

2% 2% 2%

2% 2% 2%

3~

2.875 2.875 2.875 2.875 2.875 2.875 2.875 2.875 2.875 .. 2.875 2.875 ·2.875 2.875

Plain

Standard (STDJ API Specs

5L5LX 5L5LX 5L5LX 5L 5LX 5L5LX 5L5LX 5L5LX 5L 5LX 5L 5LX 5L 5LX 5L 5LX 5L 5LX

4.000 4.000

0.083 0.109

3,47 4.53

5L 5LX SL5LX

4 4

4.500 4.500

0.083 0.109

3.92 5.11

5L 5LX 5LS 5L 5LS

Wall

X-strong (X)

Schedule

Diameter

Thickness

End Mass

XX'strong (XXSJ

No.

mm

mm

kg/m

73.0 73.0 73.0 73.0 73.0 73.0 73.0 73.0 73.0 73.0

2.11 2.77 3.18 3.58 3.96 4.37 4.78 5.16 5,49 6.35 7.01 9.53 14.02

3.69 4.80 5,48 6.13 6.74 7,40 8.04 8.63 9.14 10.44 11,41 14.92 20.39

STD

40

XS

80 160

XXS

5L 5LX 5L 5LX 5L 5LX 5L 5LX 5L 5LX 5L 5~L",X_ _ _ _ _ _ _ _ __ 5L 5 LX 5L5LX STD 40 5L 5LX 5L 5LX XS S L 5 LX 80 160 XXS 5L 5LX

3~

Outside

nO

73.0 73.0 88.9 88.9 88.9 88.9 88.9 88.9 -88.9 88.9 88.9 88.9 88.9 88.9 88.9

101.6 101.6 ~3Y.~'____~4~.0~0~0~__~0~'iI2~5~__~5~.~'7~~5~L~5~L~X~_________________________':0'.6 3~ 4.000 0.141 5.81 5L·SLX 101.6 3~ 4.000 0.156 6,40 5L 5LX 101.6 3~ 4.000 0.172 7.03 5L 5LX 101.6 3~ 4.000 0.188 7.65 5L 5LX 101.6 3~ 4.000 0.226 9.11 5L5LX STD 40 101.6 3~ 4.000 0.250 10.01 5L 5LX 101.6 3~ 4.000 0.281 11.16 5L5LX 101.6 3~ 4.000 0.318 12.50 5L 6LX XS 80 101.6 114.3 114.3

~:-------=:;:':~"'~S~~--~~;;::.;.~~T.~;----'~;;::~~:~---;~~~'-:~:';~"'~~~:=:~~~----------------------:.'-:'~~ H 4 4 4 4 4 4

4.500 4.500 4.500 4.500 4.500 4.500

0.156 0.172 0.188 0.203 0.219 0.237

7.24 7.95 8.66 9.32 10,01 10.79

5L 5LX 5LS 5L5LX5LS 5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS

STD

1074

40

114.3 114.3 114.3 114.3 114.3 114.3

2.11 2.77 3.18 3.58 3.96 4.37 4.78 5.49

Previous Status

4.52 5.88 6.72 7.53 8.29 9.11 9.92 11.29 6.3:,,5'--_712~.~~_ _ __ 14,40 7.14 7.62 15.27 11.13 21.35 15.24 27.68 2.11 2.77 3.18 3.58 3.96 4.37 4.78 5.74 6.35 7.14 8.08

5.18 6.75 7.72 8.65 9.53 10,48 11,41 13.57 14.92 16.63 18.63

.2.11 2.77 3.18 3.58 3.96 4.37 4.78 5·16 5.56

5.84 7.62 8.71 9.77 10.78 11.85 12.91 13.89 14.91 16.07

6.Q2

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI

B36.10·197~

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) Inch Units

81 Units

Identification

Inch

Outside

Wall

Nominal Size

Diameter in.

Thickness in.

Plain End Waight Ib/ft

4.500 4.500 4.500 4.500 4.500 4.500 4.500

0.250 0.281 0.312 0.337 0.438 0.531 0.674

11.35 12.66 13.96 14.98 19.00 22.51 27.54

5L 5LX 5L 5LX 5L 5LX 5L 5LX 5L 5LX 5L 5LX 5L 5LX

5LS 5LS 5LS 5LS 5LS 5LS 5LS

"5.563. 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563 5.563

0.083 0.125 0.156 0.188 0.219 .0.258 0.281 0.312 0.344 0.375 0.500 0.625 0.750

4.86 7.26 9.01 10.79 12.50 14.62 15.85 17.50 19.17 20.78 27.04 32.96 38.55

5L 5L 5L 5L 5L 5L 5L 5L 5L 5L 5L 5L 5L

5LS 5LS 5LS 5LS 5LS 5LS 5LS 5LS 5LS

6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625 6.625

0.083 ·0.109 0.125 0.141 0.156 0.172 0.188 0.203 0.219 0.250 0.280 0.312 0.344 0.375 0.432 0.500 0.562 0.625 0.719 0.864

5.80 7.59 8.68 9.76 10.78 11.85 12.92 13.92 14.98 17.02 18.97 21.04 23.08 25.03 28.57 32.71 36.39 40.05 45.35 53.16

5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX tLS 5L 5LX 5LS 5L

4 4

4 4 4 4

5

5 5 5 5 5 5 5 5

6 6

6 6 6

6 6 6 6 6 6 6 6 6 6 6 6 6 6 6

0.125 11.35 0.156 14.11 ~8~_-,-_8~.:!.62~5,-__0~'c'.1",88~_..!.-"16.94 8 8.625 0.203 18.26 0.219 19.66 8 8;625 8 8.625 0.250 22.36 8 8.625 0.277 24.70 8 8

8.625 8.625

Standard (STOI

API Specs

5L5LX 5L5LX 5L 5LX 5LX 5L 5LX 5L 5LX 5L 5LX

X-strong (X) XX·strong (XXSI

XS

Schedule No.

80 120 160

XXS

STO

40

XS

80 120 160

5LS 5LS XXS

STO

40

XS

80 120 160

XXS

5LS 5LS 5LS 5LS 5LS 5LS 5LS

20 30

1075.

Outside

Wall

Plain End

Diameter mm

Thicknt:ss mm

Mass kg/m

114.3 114.3 114.3 114.3 114.3 114.3 114.3

6.35 7.14 7.92 8.56 11.13 13.49 17.12

16.90 18.87 20.78 22.32 28.32 33.54 41.03

141.3 141.3 141.3 141.3 141.3 .141.3 141.3 141.3 141.3 141.3 141.3 141.3 141.3

2.11 3.18 3.96 4.78 5.56 6.55 7.14 7.92 8.74 9.53 12.70 15.88 19.05

7.24 10.83 13.41 16.09 18.61 21.77 23.62 26.05 28.57 30.97 40.28 49.11 57.43

168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3 168.3

,2.11 2.77 3.18 3.58 3.96 4.37 4.78 5.16 5.56 6.35 7.11 7.92 8.74 9.53 10.97 12.70 14.27 15.88 18.26 21.95

8.65 11.31 12.95 14.54 16.05 17.67 19.27 20.76 22.31 25.36 28.26 31.32 34.39 37.31 42.56 48.73 54.20 59.69 67.56 79.22

Previous

Status

c

219.1 3.18 16.93 21.01 219.1 3.96 _~~.1_ _~4~."7,8~_-=2~5~.2~6_ _ ___ 219.1 5.16 27.22 29.28 219.1 5.56 219.1 6.35 33.31 219.1 7.04 36.81

AMERICAN NATIONAL STANDARD WELDED·AND:SEAMLESS WROUGHT STEEL PIPE

ANSIB36.1 ()';1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) 51 Units

Inch Units Identification

Plain Inch Nominal Size

Standard (STD)

Out'side Diameter in.

Wall Thickness in.

End Weight Ib/ft

8 8 8 8 8 8 8 8 8 8 8 8 8 8

8.625 8.625 8.625 8.625 8.625 8.625 8.625 8.625 8.625 8.625 '.8.625 8.625 8.625 8.625

0.312 0.322 0.344 0.375 0;406 .0.438 0.500 0.562 0.594 0.625 0.719 . 0.812 0.875 0.906

.27.70 78.55 3Q.42 33.04 35.64 38.30 43.39 48.40 50.95 53.40 60.71 67.76 72.42 74.69

10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10,750 10.750 10.750 10.750 10.750 10.750 10.750 10.750

0.156 0.188 0.203 0.219 0.250 0.279 0.307 0.344 0.365 0.438 0.500 0.562 0.594 0.625 0.719 0.812 0.844 1.000 1.125

1.7.65 21..21 22.87 24.1>3 28.04 31.20 34.24 38.23 40.48 48.24 ", 54.74 61.15 64-.43 67.58 77.03 86.18 89.29 104.13 115.64

5L 5LX 5LS 5L 5LX 5LS 5 LX 5 LS 5L 5LX SLS SL SLX SLS 5L 5LXSLS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS

12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

12.750 12.750 12.750 12.750 12,750 12.750 12.7S0 12.7S0 12.7S0 12.750 12.750 12.750 12.7S0 12.7S0 12.750

0.172 0.188 0.203 0.219 0.250 0.281 0.312 0.330 0.344 0.375 0.406 0.438 0.600 0.562 0.625

23.11 25.22 27.20 29.31 33.38 37.42 _41.4S 43.77 45.58 49.S6 53.S2 S7.59 65.42 73.15 80.93

5L 5LX 5LS 5L 5LX 5LS 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS SL SLX 5LS SL SLX SLS SL SLX 5LS 5L SLX 5LS 5LX 5LS 5L SLX SLS 5L 5LX SLS 5L5LXSLS 5L SLX SLS

X~strong

API

Specs

5L 5LX 5L 5LX 5L 5LX 5L 5LX

5LS 5LS 5LS 5LS

(X)

XX·strong (XXS)

STD

Schedule

No.

40

60 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS

XS

80' 100

5L 5LX 5LS 5L 5LX 5LS 5L

120 140 XXS 160

20 30 STD

40

XS

60 80

5L 5LX 5LS 5L SLX 5LS 5L 5LS

100

XXS

120 140 160

20

30 STD

40 XS

60

1076

Outside

Wall

Plain End

Diameter

Thickness

Mass

mm

mm

kgim

219.1 219.1 219.1 219.1 219.1 219.1 219 ..1 219.1 219.1 219.. 1 219.1 219.1 219.1 219.1

7,92 8.18 8;74 9.53 10.31 11.13 '·12.70 14.27 15.09 15.88 18.26 20.62 22.23 23.01

41.24 42.55 45.34 49.25 53.08 57.08 64.64 72.08 75.92 79.58 90.44 100.92 107.92 111.27

273.1 273.1 273.1 273.1 273,1 2}3.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1 273.1

3.96 4.78 S.16 5.56 6.35 7.09 7.80 8.74 9.27 11.13 12.70 14.27 15.09 15.88 18.26 20.62 21.44 25.40 28.58

26.28 31.63 34.09 36.68 41.77 46.51 51.03 56.98 60.31 71.90 81.55 91.08 96.01 100.73 114.75 128.38 133.06 155.15 .172.33

323.9 3.23.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9

4.37 4.78 5.16 5.56 6.35 7.14 7.92 8.38 8.74 9.S3 10.31 11.13 12.70 14.27 lS.88

34.43 37.62 40.56 43.65 49.73 5S.77 61.71 65.20 67.93 73.88 79.73 85.84 97.46 108.96 120.62

Previous ,Status

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI B36.1 0-1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) Inch Units

SI Units (Identification

Plain Inch Nominal Size

Wall Thickness in.

End Weight Ib/ft

12 12 12 12 12 12 12 12

12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750

0.G88

0.750 0.812 0.844 0.875 1.000 1.125 1.312

88.63 96.12 103.53 107.32 110.97 125,49 139.67 160.27

5L 5LX 5LS 5L 5LX·5LS 5L 5LX 5LS

14 14 14 14 14 14 14 14 14 14 14 14 14 14

14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000

0.188 0.203 0.210 0.219 0.250 0.281 0.312 0.344 0.375 0,406 0.438 0,469 0.500 0.562 --'1_'_4_~__'1_'_4:;:.0.:;0=_0_-:;0.594 14 14.000 0.625 14 14.000 0.688 14 14.000 0.750 14 14.000 0.812 14 14.000 0.875 14 14.000 0.938 14 14.000 1.094 14 14.000 1.250 14 14.000 1.406 14 14.000 2.000 14 14.000 2.125 14 14.000 2.200 14 14.000 2.500

27.73 29.91 30.93 32.23 36.71 41.17 45.61 50.17 54.57 58.94 63,44 67.78 72.09 80.66 85.05 89.28 97.81 106.13 114.37 122.65 130.85 150.79 170.21 189.11 256.32 269.50 277.25 307.05

5L5LX5LS 5L 5LS 5 LX 5 LS 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5 LX 5 LS 5L 5LX 5LS 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS

0.188 0.203 0.219 0.250 0.281 0.312 0.344 0.375 0,406 0.438 0.469 0.500

31.75 34.25 36.91 42.05 47.17 52.27 57.52 62.58 67.62 72.80 77.79 82.77

5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LX 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5LX 5LS 5L5LX5LS 5LX 5LS 5L 5LX 5LS

16 16 16 16 16 16 16 16 16 16 16 16

16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000

Plain

Standard (STDI

Outside Diameter in.

API Specs

Outside

Wall

End

Previous

Status

X-strong (X)

Schedule

Diameter

Thickness

XX·strong (XXSI

No.

mm

mm

Mass kg/m

80

323.9 323.9 323.9 323.9 323.9 323.9 323.9 323.9

17,48 19.05 20.62 21.44 22.23 25,40 28.58 33.32

132.08 143.21 154.21 159.91 165.37 186.97 208.14 238.76

355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6 355.6

4.78 5.16 5.33 5.56 6.35 7.14 7.92 8.74 9.53 10.31 11.13 11.91 12.70 14.27 15.09 15.88 17,48 19.05 20.62 22.23 23.83 27.79 31.75 35.71 50.80 53.98 55.88 63.50

100 5L5LX5LS XXS

120 140 160

10 20 STD

30 40

XS

60 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS

80

100 120 140 160

10 20 STD

30

XS

40

'1077

41.35 44.59 46.04 47.99 54.69 61.35 67.90---74.76 81.33 87.79 94.55 100.94 107.39 120.11 126.71 133.03 145.75 158.10 170.33 182.75 194.96 224.65 253.56 281. 70 381.83 '401.50 413.01 457.40

406.4 4.78 47.34 406.4 ~16 51~6 406.4 5.56 54.96 . 406.4 6.35 62.64 406.4 7.14 70.30 406.4 '7.92 77.83 406.4 8.74 85.71 406.4 9.53 93.27 406.~.4_ _ _1~0~.3~1~_~1~0~0~.7~0~_ ___ 406.4 11.13 108.49 406.4 11.91 115.86 406.4 12.70 123.30

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10-1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) 81 Units

Inch Units Identification

Plain

Plain

Standard ISTD)

Inch Nominal

Outside Diameter

Wall Thickness

End Weight

Size

in.

in.

Ib/ft

16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16

16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000

0.562 0.625 0.656 0.688 0.750 0.812 0.844 0.875 0.938 1.000 1.031 1.062 1.125 1.219 1.438 1.594

92.66 102.63 107.50 112.51 122.15 131.71 136.61 141.34 150.89 160.20 164.82 169.43 178.72 192.43 223.64 245.25

5L 5LX 5LS 5L 5LX 5LS

18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18

18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000

0.188 0.219 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0,459 0.500 0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.156 1.188 1.250 1.375 1.562 1.781

35.76 41.59 47.39 53.18 58.94 64.87 70.59 76.29 .82.15 87.81 93.45 104.67 115.98 127.21 138.17 149.06 160.03 170.92 181.56 192.11 202.75 207.96 213.31 223.61 244.14 274.22 308.50

5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5LX 5LS 5L5LX5LS 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS

20 20 20 20 20

20.000 20.000 20.000 20.000 20.000

0.219 0.250 0.281 0.312 0.344

46.27 52.73 59.18 65.60 72.21

API Specs

X-strong (XI

Schedule

Diameter

Thickness

No.

mm

mm

End Mass kg/m

406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4 406.4

14.27 15.88 16.66 17.48 19.05 20.62 21.44 22.23 23.83 25.40 26.19 26.97 28.58 30.96 36.53 40.49

137.99 152.93 160.12 167.65 181.97 196.16 203.53 210.60 224.82 238.64 245.56 252.35 266.28 286.64 333.19 365.35

60

80 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 100 5L 5LX 5LS 5L 5LX 5LS 120 140 160

10 20 STD

30 XS 'lU

60

80

100 5L 5LX 5LS 5L 5LX 5LS 120 140 160 5LX 5LX 5LX 5LX 5LX

Wall

XX-strong IXXS)

5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS

5L 5L 5L 5L 5L

Outside

5LS 5LS 5LS 5LS 5LS

10

1078

Previous Status

457 4.78 53.31 457 5.56 61.90 457 6.35 70.57 457 7.14 79.21 457 7.92 87.71 457 8.74 96.61 457 9.53 105.16 457 10.31 113.57 457 11.13 122.38 457 11.91 130.72 457 12.70 139.15 457 _ _--'-'4"'.=.27'c---__'''''5'''5'''.8'''0'---_ __ 457 15.88 172.74 457 17.48 189.46 457 19.05 205.74 457 20.62 221.89 457 22.23 238.34 457 23.83 254.55 25.40 270.34 457 457 26.97 286.00 457 28.58 301.94 457 29.36 309.62 457 30.18 317.66 457 31.75 332.95 457 34.93 363.56 457 39.67 408.26 457 45.24 459.37 508 508 508 508 508

5.56 6.35 7.14 7.92 8.74

68.89 78.55 88.19 97.67 107.60

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI B36.10-1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) Inch Units

51 Units

I nch

Outside

Wall

Plain End

Nominal

Diameter

Thickness

Weight

Size

in.

. in.

Ib/ft

20 20 20 20 20

20.000 20.000 20.000 20.000 20.000

Identification

Plain

Standard (STD)

OutSide

Wall

End

Previous

X-strong (X)

Schedule

Diameter

Thickness

Mass

Status

XX·strong (XXS)

No.

mm

mm

kg/m

20

508 S08 S08 S08 508

9.53 10.31 11.13 11.91 12.70

'117.15 126.S3 136.37 145.70 155.12

20 20.000 1.500 296.37 120 508 20 20.000 1.750 341.09 140 508 --;:.20:c----;020"'.~00;;:0:c---::-1.96;o9--..;3:;:7;;9c:.l;::7:------~---~~-------:1 60-'--508

38.10 44.45 50,01

441.d9 508.11 564.81

0.375 0.406 0.438 0.469 0.500

78.60 84.96 91.S1 97.83 104'.13

API Specs

SL SLX SLX SLSLX S LX SL SLX

5 LS SLS SLS S LS SLS

STD

XS 30 __~2~0_ _~2~0.~0~0~0_ _~0.~S~627-~1~1~6~.6~7_~S~L~S~L~X~S=LS~_ _ _ _ _ _ _ _~_ _~S.08 ___~1~4.~2~7--~1~73~.~74~_ __ 20 20.000 0.S94 123.11 40 508 15.09 183.42 20 20.000 0.625 129.33 SL SLX SLS 508 lS.88 192.71 20 20.000 0.688 141.90 SL SLX SLS 508 17.48 211.44 20 20.000 0.750 154.19 SL SLX SLS 508 19.05 229.70 20 20.000 0.812166.40 SLSLXSLS 60' 508 20.62 247.83 20 20.000 0.875 178.72 SL SLX SLS 508 22.23 266.29 20 20.000 0.938 190.96 SL SLX SLS 508 23.83 284.52 20 20.000 1.000 202.92 SL SLX SLS 508 25.40 302.28 20 20.000 1.031208.87 80 508 26.19 311.17 20 20.000 1.062 214.80 SL SLX SLS 508 26.97 319.92 20 20.000 1.12S 226.78 SL SLX SLS 508 28.58 337.89 20 20.000 1.188 238.68 SL SLX SLS 508 30.18 355.61 20 20.000 1.250 250.31 SL SLX SLS 508 31.75 372.88 20 20.000 1.281 256.10 100 508 32.54 381.53 20 20.000 1.312 261.86 SL SLX SLS 508 33.32 390.03 --"-20:--....::.20"'."'0~0·0:---1;.:.~37="5:---,:2:;:.73;.51 5L SLX 5 LS:------------.,:S:-=0"'8--~3"'4"'.::'.93"----=40"'7::.;.;:;49:-----

22 22 22 22 22 22

22.000 22.000 22.000 22.000 22.000 22.000

. 0.219 0.250 0.281 0.312 0.344 0.375

22 22 22 22 22 22 22 22 22 22 22 22 22 22

22.000 22.000 22.000 22.000 22:000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000

0.562 0.62S 0.688 0.7S0 0.812 0.87S 0.938 1.000 1.062 1.12S 1.188 1.2S0 1.312 1.37S

50.94 58.07 65.18 72.27 79.56 86.61 -2"'2:----:2"'2--:.0"'O-O:O---,OAo6 93.63 22 22.000 0.438 100.86 22 22.000 0.469 107.85 -2~2:---722~.-O:OO~0:--~0~.S~0~0:-~17147.~8~1128.67 142.68 156.60 170.21 183.7S 197.41 211.00 224.28 237.48 250.81 264.06 277,01 289.88 302.88

5L 5LX 5LS. 559 5:56 75.88" SL SLX 5LS 10 559 6.35 86.54 SLSLX5LS 559 7.14 97.17 SL SLX SLS SS9 7.92 107.63 SL SLX SLS 559 8.74 118.60 SL SLX SLS STD 20 559 9.53 129.13 c SLX SLS 559 10.31 139.50 SL SLX SLS 559 ":13 150.37 SLX SLS 559 11.91 160.68 SL5=LX~S~L~S---~X~S~----~3~0---=SS"'9:--~1~2.~7~0-----1--:7~1--:.0:-;;9~---SL SLX SL SLX SL SLX SL SLX SL SLX SL 5LX SL5LX SL SLX SL 5LX 5L SLX 5L SLX SLSLX SL SLX SL SLX

SLS SLS SLS SLS 5LS 5LS SLS SLS SLS SLS 5LS SLS SLS S LS

60

80

100

1079

559 559 S59 S59 . SS9 SS9 559 559 SS9 559 SS9 559 SS9 5S9

14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75 33.32 34.93

191.69 212.69 233.43 2S3.65 273.76 294.25 314.49 334.23 353.84 373.83 393.S7 412.81 431.94 4S1.42

AMERICAN NATIONAL STANDARD WELDED. AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10-1979

Table 2 DimensiQns and Weights Qf Welded and S~amless Wrought Steel Pipe (Continued) SI Units

IflCh Units Identification

Outside Diameter

Ttlickness

in.

in.

Plain End Weight Ib/ft

22 22 22 22 22

22.000 22.000 22.000 22.000 22.000

1,438 1.S00 1.62S 1.87S 2.125

31S.79 328.'-1 3S3.61 403.00 4S1.06

SL SLX SLS SL SLX SLS

'24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24

24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.0 00 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 2,4.000 24.000 24.000 24.000 24.000 24.000 24.000

0.2S0 0.281 0.312 0.344 0.37S 0,406 0,438 0.4S9 O.SOO 0.S62 0.625 0.688 0.750 0.812 0.875 0.938 0.969 1.000 1.062 1.12S 1.188 1.219 1.2S0 1.312 1.37S 1.438 1.500 1,S31 l.S62 1.812 2.062 2.344

63.41 71.18 78.93 86.91 94.62 102.31 110.22 117.86 12S.49 14Q.68 156.03 171.29 186.23 201.09 216.10 23'1.03 238.35 24S.64 260.17 274.84 289,44 296.S8 303.71 317.91 332.25 346.S0 360.4S 367.39 374.31 429.39 483.12 542.13

SL SLX SLS SL SLX SLS SL SLX 5LS SL SLX SLS SL SLX 5LS SLX SLS 5L SLX SLS SLX SLS SL SLX SLS SL SLX 5LS 5L 5LX 5LS 5L 5LX SLS 5L 5LX 5LS 5L 5LX 5LS SL 5LX 5LS 5L 5LX 5LS

26 26 '26 26 26 26 26 26 26 26 26

26.000 26.000 26.000 26.000 26.000 26.000 26.000 26000 26.000 26.000 26.000

0.250 0.281 0.312 0.344 0.375 0,406 0.438 0.469 O.SOO 0.S62 0.62S

68.7S 77.18 8S.60 94.26 102.63 110.98 119.57 127.88 136.17 1S2.68 169.38

Inch Nominal Size

Wall

Standard (STDI X·strong (Xl XX·strong (XXSI

API Specs

Plain

Schedule No.

120 140 160 10

STD

20

XS 30 40

60 SL SLX 5L 5LX SL SLX SL 5LX

SLS SLS SLS SLS

SL SLX SL SLX SL SLX SL SLX SL 5LX

SLS SLS SLS 5LS SLS

80

100 5L 5LX 5LS 120 140 160 5L 5LX SL 5LX SL 5LX SL SLX SL SLX SLX SL SLX SLX 5L SLX SL 5LX SL 5LX

SLS SLS SLS SLS SLS SLS SLS SLS SLS 5LS 5LS

10 STD

XS

1080

20

Outside

Wall

Diameter

Thickness

mm

mm

End Mass kg/m

SS9 SS9 559 559 559

36.S3 38.10 41.28 47.63 S3.98

470.66 489,41 527.02 600.63 672.26

610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 610 61 0 610 610 610 610 610 610

ii.35 7.14 7.92 8.74 9.S3 10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 24.61 2S,40 26.97 28.58 30.18 30.96 31.7S 33.32 34.93 36.53 38.10 38.89 39.67 46.02 52.37 S9.S4

94.53 106.15 117.59 129.59 141.12 1S2.47 164.37 175.66 187.06 209.64 232.66 255.41 277.61 299.69 322.21 344.46 35S.26 366.17 ,'387.76 409.77 431.S2 442.08 4S2.74 473.84 49S.35 S16.80 S37.33 547.71 SS7,43 640.03 720.15 808.22

660 660 660 660 660 660 660 660 660 660 660

6.3S 7.14 7.92 8.74 9.53 10.31 11.13 11.91 12.70 14.27 1S.88

102.36 114.9S 127.36 140.37 152.87 16S.18 178.09 190.34 202.72 227.23 2S2.24

Previous

Status

C

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10-1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) Inch Units

SI Units

Identification

Plain

Outside

Wall

End

Nominal

Diameter

Thickness

Weight

Size

in.

in.

l!l/ft

API Specs

26 26 26 26 26 26

26.000 26.000 26.000 26.000 26.000 26.000

0.688 0.750 0.812 0.875 0.938 1.000

185.99 202.25 218.43 234.79 251.07 267.00

5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS

28 28 28 28 28 28 28 28 28 28 28 28 28 28 28

28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000 28.000

0.250 0.281 0.312 0.344 0.375

74.09 83.19 92.26 101.61 110.64 119.65 128.93 137.90 146.85 164.69 182.73 200.68 218.27 235.78

5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5LX 5LS 5L5LX5LS 5LX 5LS 5L 5LX 5LS 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L5LX5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS

00406 00438 00469

0.500 0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000

253048

271.10 288.36

Plain

Standard (STOI

Inch

Outside

Wall

End

Previous

Status

X-strong (X)

Schedule

Diameter

Thickness

XX·strong (XXSI

No.

mm

mm

Mass kg/m

660 660 660 660 660 660

17.48 19.05 20.62 22.23 23.83 25.40

276.96 301.1 0 325.12 349.62 373.84 397.49

711 ·711 711 711 711 711 711 711 711 711 711 711 711 711 711 711 711

6.35 7.14 7.92 8.74 9.53 10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40

110.34 123.93 137.32 151.36 164.85 178.15 192.09 205.32 218.69 245.18 271.21 298.95 325.06 351.05 377.58 403.81 429.44

10 STO

XS

20 30

30 30.000 0.250 79043 5L 5LX 5LS 30 30.000 0.281 89.19 5L5LX 5LS 30 30.000 0.312 98.93 5L 5LX 5LS 10 30 30.000 0.344 108.95 5LX 5LS 30 30.000 0.375 118.65 5L 5LX 5LS STO 30 30.000 00406 128.32 5 LX 5 LS 30 30.000 00438 138.29 5L 5LX 5LS 00469 147.92 5LX 5LS 30 30.000 157.53 5L 5LX 5LS XS 20 30 30.000 0.500 30 30.000 0.562 176.69 5L 5LX 5LS . 30 30.000 0.625 196.08 5L 5LX 5LS 30 30 30.000 0.688 215.38 5L 5LX 5LS 30 30.000 0.750 234.29 5L 5LX 5LS 30 30.000 0.812 253.12 5L 5LX 5LS _-=3~0_ _..;3:;0::.:.0:;0~0_ _::0.~8",75~---:2:::7~2",.1:-;7_.-o57'-L-::5"'L.,-;x..,5,.,L'''S-----------291.14 5L 5LX 5LS 30 30.000 0.938 30 30.000 1.000 309.72 5L 5LX 5LS

762 6.35 118.33 762 7.14 132.91 762 7.92 147.28 762 8.74 162.35 762 9.53 176.84 762 10.31 191.1 1 762 11.13 206.09 762 11.91 220.30 762 12.70 234.67 762 14.27 263.12 762 15.88 292.18 762 17048 320.93 762 19.05 349.02 762 20.62 376.98 762 22.23 405.54 762---23.83·--4:;:3"'3;:.7"'8':----762 25040' 461.38

_~30~-__::3~0"'.0~0~0--1~.~06~2~__::3~2~8."'2~2-_;5L~5~L~X~5~LS~-----------~7~6~2--~2~6~.9~7--~478::8.~8~5-~N~30 30 30

30.000 30.000 30.000

1.125 1.188 1.250

346.93 365.56 383.81

5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS

762 762 ~62

28.58 30.18 31.75

516.90 544.65 571.75

32 32 32

32.000 32.000 32.000

0.250 0.281 0.312

84.77 95.19 105.59

5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS

813 813 813

6.35 7.14 7.92

126.31 141.89 157.24

10.

1081

N N N

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

.

ANSI

.'

B36.10-1~79

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) 81 Units

Inch Units

Identification

Inch

Outside

Wall

Plain End

Nominal Size

Diameter in.

Thickness in.

Weight Ib/tt

API Specs

32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32

32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.600 32.000 32.000

0.344 0.375 00406 0.438 00469 0,500 0.562 0.62S 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.12S 1.188 1.2S0

116.30 126.66 136.99 147.64 157.94 168.21 188.70 209043 230.08 250.31 270.47 290.86 311.17 331.08 350.90 370.96 390.94 410.S1

5LX5LS 5L 5LX 5LS 5LX 5LS 5L 5LX 5LS 5LX 5LS 5L 5LX 5LS 5L SLX 5LS 5L 5LX 5LS SL SLX 5LS 5L 5LX 5LS 5L SLX SLS SL 5LX 5LS SL5LX5LS SL 5LX 5LS 5L 5LX SLS SL SLX SLS 5L 5LX 5LS SL SLX SLS

34 34 34 34 34 34 24 34 34 34 34 34 34 34 34 34 34 34 34 34 34

34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34'.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000

0.250 0.281 0.312 0.344' 0.37S 0.406 0.438 0.469

90.11 101.19 112.2S 123.6S 134.67 14S.67 157.00 167.9S 178.89 200.70 222.78 244.77 266.33 287.81 309.55 331.21 352.44 373.59 394.99 416.31 437.21

5L SLX SLS SL SLX SLS SLSLXSLS SLX SLS SL 5LX SLS SLX SLS 5L SLX 5LS SLX 5LS 5L 5LX 5LS SL 5LX 5LS 5L 5LX SLS 5L 5LX SLS 5L 5LX SLS 5L SLX SLS SL 5LX SLS 5L 5LX SLS 5L 5LX SLS SL 5LX SLS 5L 5LX SLS 5L5LXSLS 5L SLX SLS

36 36 36 36 36 36 36 36 36

36.000 36.000 36.000 36.000 3Q.000 36.000 36.000 36.000 36.000

9S.45 107.20 118.92 131.00 142.68 154.34 166.3S 177.97 189.S7

SL 5LX 5LS SL 5LX SLS 5LSLXSLS 5LX 5LS 5L 5LX 5LS 5LX SLS 5L SLX SLS SLX SLS SL SLX SLS

O.SOO

0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.469 O.SOO

Standard (STD) X-strong (Xl XX-strong (XXS)

Plain Schedule

No.

STD

XS

20 30 40

10 STD

XS

20 30 40

10 STD

XS

1082

20

Outside Diameter mm

Wall Thickness mm

End

Previous

Mass kg/m

Status

813 813 813 813 813 813 813 813 813 813 813 813 813 813 813 813 813 813

8.74 9.53 10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.S8 30.18 31.75

173.34 188.82 204.08 220.08 235.28 250.64 281.07 312.15 342.91 372.98 402.92 433.49 463.7S 493.32 S22.77 SS2.8S S82.61 611.68

N N

864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864 864

6.35 7.14 7.92 8.74 9.53 10.31 11.13 11.91 12.70 14.27 lS.88 17.48 19.0S 20.62 22.23 23.83 2S.40 26.97 28.S8 30.18 31.75

134.30 lS0.87 167.20 184.33 200.31 217.0S 234.08 2S0.26 266.61 299.02 332.12 364.90 396.93 428.8S 461.4S 493.72 S2S.27 556.69 588.79 620.56 651.61

N N N N

914 914 914 914 914 914 914 914 914

6.35 142.13 7.14 159.67 7.92;.-_-71,::76='."'96;-_ __ 8.74 19S.11 9.S3 212.S6 229.76 10.31 11.13 247.31 11.91 264.94 12.70 282.27

N

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10-1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) Inch Units

SI Units

I nch Nominal Size

Outside Diameter in.

Wall Thickness in.

Plain End Weight Ib/ft

36 36 36 36 36 36 36 36 36 36 36 36

36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000

0.562 0.625 0.688 0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250

212.70 236.13 259.47 282.35 305.16 328.24 351.25 373.80 396.27 419.02 441.69 463.91

38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38

38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 38.000 .38.000 38.000 38.000

40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40

40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000 40.000

Identification

API Specs

5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS

125.58 0.312 0.344 138.35 0.375 150.69 0.406 163.01 0.438 175.71 0.469, 187.99 0.500 200.25 224.71 0.562 249.48 0.625 0.688 274.16 0.750 298.37 322.50 0.812 346.93 0.875 0.938 371.28 .395.16 1.000 1.062 418.96 1.125 '443.05 1.188 467.06 490.61 1.250

5L5LX5LS 5L 5LX 5LS 5L5LX5LS 5 L 5 LX 5 LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS 5 L 5 LX 5 LS

0.312 0.344 0.375 0.406 0.438 0.469 0.500 0.562 0.625 0.688 0.750 0.812 0.8 75 0.938 1.000 1.062 1.125

5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS 5L 5LX 5LS

132.25 145.69 158.70 171.68 185.06 198.D1 210.93 236.71 262.83 288.86 314.39 339.84 365.62 391.32 416.52 441.64 467.08

St;ndard (STO) X·strong (X) XX·strong (XXS)

Plain Wall Thickness

End

Previous

Schedule

Outside Diameter

Mass

Status

No.

mm

mm

kg/m

914 914 914 914 914 914 914 914 914 914 914 914

14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75

316.11 351.70 386.45 420.42 454.27 488.86 523.11 556.59 589.95 624.03 657.77 690.76

965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965 965

• 7.92 8.74 9.53 10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75

186.92 206.10 224.54 242.72 261.80 279.92 298.24 334.56 371.68 408.43 444.38 480.21 516.82 553.08 588.53 623.87 659:97 695.73 730.69

1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 1016 . 1016 1016 1016

7.92 8.74 9.53 10.31 11.13 11.91 12.70 14.27 15.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58

196.89 217.09 236.53 255.69 275.80 294.90 314.22 352.51 391.65 430.42 468.34 506.14 544.78 583.05 620.48 657.78 695.92

30 40

STO

XS

STO

XS

1083

N N

N N

N N N N

N N

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10-1979

Table 2 Dimensions and:,V'ieights ,o~ Welded and Seamless Wrought :iteel Pipe (Continuec;l) Inch U,nits

81 Units I~entifi,?ation

Inch Nominal Size

Outside Diameter in.

Wall Thickness in.

Plain ,End Weight, Ib/ft

40 40

40.000 40.000

1.188 1.2S0

492.44 S17,31

SL SLX SLS SL SLX SLS

42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42 42

42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42·000

0.344 0.37S 0.406 0.438 0.469

153.04 166.71 180.35 194.42 208,03 221.61 248.72 276.18 303.5S 330.41 3S7.19 384.31 411.3S 437.88 4,64.32 491.11 S17.82 S44.01

SL SLX SLS 5L 5LX SLS 5L 5LX 5LS SL 5LX SLS SL 5LX SLS 5L 5LX 5LS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SLSLXSLS SLSLX SLS SL SLX SLS SL SLX SLS

44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44 44

A4.000 44.090 44.000 44.000 44.000 44.000 44.000 44.000 44.000 4.4.000 44.000 44.000 44.000 44.000 44.000 44.000 44.000 44.000

160.39 174.72 189.03 203.78 218.04 232.29 260.72 289.S3 318.2S 346.43 374.S3 403.00 4S9.24 487.01 S15.14 543.19 S70.71

SL SLX SLS SL SLX 5LS SL 5LX 5LS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS SL SLX SLS

46 46 46 46 46 46 46 46 46

46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000

167.74 182.73 197.70 213.13 . 228.06 242.97 272.73 302.88 332.95

SL SLX SL SLX SL SLX 5L 5LX SL SLX SL SLX 5L 5LX SL eLX SL SLX

O.SOO

0.562 0.62S .0.688 0.7S0 0.812 .0.87S 0.938 1.000 1.062 1.12S 1.188 1.2S0 0.344 0.375 0.406 0.438 0,4S9 O.SOO

0.S62 0.62S 0.688 0,7S0 0.812 0.87S 0.938 1.000 1.062 1.125 ·,.188 1.2S0 0.344 0.37S 0.406 0,438 0,4S9 O.SOO

0.562 0.625 0.688

~31.39

Plain

Standard (STD) API Specs

SLS 5LS SLS SLS SLS SLS SLS 5LS SLS

X-strong (Xi)

Schedule

XX·strong (X1(S)

No.

STD

XS

STD

XS

STD

XS

1084

Outside Diameter mm

- Wall

End

Previous Staw~,

rnm

Mass kg/m

1016. 1016

30.18 31.75

733.68 770.62

N N

1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 1067 10E!7

8.74 9.53 10.31 11.13 11.91 12.70 14.27 1S.88 17.48 19.0S 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75

228.09 248.52 268.66 289.80 309.88 330.19 370.4S 411.62 452.40 492.30 S32.07 S72. 73 613.02 652.42 691.70 731,86 771.64 810.55

N N N N

1118 ·1118 1118 1118 1118 1118 1118 1118 1118 1118 1118 11.18 1118 1118 1118. 1118 1118 1118

8.74 9.53 10.31 11-13 11.91 12.70 14.27 1S.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75

239.08 260,50 281.62 303,80 ,324.80 G46.16 388.40 431.S9 474.37 S16.26 SS8.00 600.69 642.99 684.37 725.62 767.80 809.60 850.48

N N N

1168 1168 1168 1168 1168 1168 1168 1168 1168

8.74 9.S3 10.31 11.13 11.91 12.70 .14.27 1S.88 17,48

249.85 272.25 294.34 317.52 339.S4 3S1,82 406.00 451.17 49S.94

Thickness

AMERICAN NATIONAL STANDARD WELDED AND SEAMLESS WROUGHT STEEL PIPE

ANSI 836.10-1979

Table 2 Dimensions and Weights of Welded and Seamless Wrought Steel Pipe (Continued) Inch Units

81 Units Identification

Inch

Outside

Wall

Plain end

Nominal Size

Diameter in.

Thickness in.

Weight Ib/ft

API Specs

46 46 46 46 46 46 46 46 46

46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000 46.000

0.750 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250

362.45 391.88 421.69 451.42 480.60 509.69 539.17 568.S7 597.41

5L 5LX 5LS 5L 5LS 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS SL SLX 5LS 5L 5LX 5LS 5L 5LX 5LS

48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48

48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000 48.000

0.344 0.375 0.406 0.438 0.469 0.500 0.562 0.625 0.688 0.7S0 0.812 0.875 0.938 1.000 1.062 1.125 1.188 1.250

175.08 190.74 206.37 222.49 238.08 253.65 284.73 316.23 374.64 378.47 409.22 440.38 471.46 501.96 S32.38 563.20 593.94 624.11

5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS SL 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS SL SLX SLS SL 5LX SLS 5LSLXSLS SL 5LX 5LS SL SLX SLS SL 5LX 5LS 5L SLX SLS 5L 5LX 5LS 5L 5LX 5LS 5L 5LX 5LS 5L5LX5LS

Standard (STD) X·strong (X) XX·strong (XXS)

STD

XS

Plain

Schedule

No.

Outside Diameter mm

Wall. Thickness mm

1168 1168 1168 1168 1168 1168 1168 1168 1168

19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75

539.76 583.43 628.10 672.37 715.68 758.88 803.04 846.81 889.63

N N N N

1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219 1219

8.74 9.53 10.31 11.13 11.91 12.70 14.27 lS.88 17.48 19.05 20.62 22.23 23.83 25.40 26.97 28.58 30.18 31.75

260.85 284.24 307.30 331.S2 354.52 377.79 423.94 471.14 517.92 563.70 609.36 656.06 702.34 747.63 _ 792.80 838.99 884.77 929.56

N N N N

End Mass

k~im

Previous Status

52 S2

52.000 0.375 206.76 5L 5LX 5LS 132" 9.53 308.21 N 52.000 0.406 223.72 5L 5LX 5LS 1321 10.31 333.24 iii _:::S2~__5:::2~.0~0~0;_--;:0.438c---;2;;:4",1~.2~0--;5:-;:L:.;5~L~X:-:5",L::;Sc-_ _ _ _ _ _ _ _ _ _ __:_1~32~1;_-__:_1_:_1:.;.1:;3_ _.-;3o;5;::9::.;.5",1:-__:_N,:-_ 52 52,000 0.469 258.115L5LX5LS 1321 11.91 384.48 N 52 52.000 0.500 275.01 SL 5LX 5LS 1321 12.70 409.64 N S2 52.000 0.562 308.74 SL 5LX 5LS 1321 14.27 459.84 N 52.000 0.625 342.93 5L 5LX 5LS 1,32" 15.88 511.09 N 52 S2 52.000 0.688 377.03 SL 5LX 5LS 1321 17.48 S61.89 N S2 S2.000 0.7S0 410.S1 SLSLXSLS 1321 19.05 611.62 N 52.000 0.812 443.91 5L 5LX 5LS 1321 20.62 661.23 N 52 52 52,000 0.875 477.76 5L 5LX 5LS 1321 22.23 711.98 N 52 52.000 0.938 511.53 5L 5LX 5LS 1321 23.83 762.28 N 52.000 1.000 544.68 ,SL 5LX 5LS 1321 25.40 811.52 N 52