ADAPTIVE CRUISE CONTROL SYSTEM

A Seminar Report on ADAPTIVE CRUISE CONTROL SYSTEM Prepared by : Harshad S. Patel Roll No.

: 130420704010

Class

: ME (Electronics & Communication)

Semester

: III

Year

:

Guided by

: Prof. Vandana Shah

2014-15

Department Of Electronics & Communication Engineering Sarvajanik College of Engineering & Technology Dr R.K. Desai Road, Athwalines, Surat - 395001, India

ADAPTIVE CRUISE CONTROL SYSTEM 1

A Seminar Report Submitted by

Harshad S. Patel 1304207040

in partial fulfillment for the award of the degree of

MASTER OF ENGINEERING IN

ELECTRONICS & COMMUNICATION ENGINEERING

Year- 2013-14 At

SARVAJANIK COLLEGE OF ENGINEERING & TECHNOLOGY DR.R.K. DESAI ROAD, ATHWALINES SURAT-395001,INDIA

2

Sarvajanik College of Engineering & Technology Dr R.K. Desai Road, Athwalines, Surat - 395001, India.

Department Of Electronics & Communication Engineering

CERTIFICATE This is to certify that the Seminar report entitled Adaptive Cruise Control System is prepared & presented by H a r s h a d S . P a t e l Enrollment No 130420704010 of M.E.II Sem. III Electronics & Communication Engineering during year 20132014. His work is satisfactory.

Signature of Guide Department

Head

of

Electronics & comm. Engineering

Signature of Jury Members

3

Abstract Cruise control is a new technological development which incorporates a factor of comfort in driving. Safety is only a small benefit of this system. In short, cruise control can be said to be a system which uses the principles of radar to determine the distances between two consecutive moving vehicles in which either one or both of them is incorporated with this system. The electromagnetic rays from radar system are sensed by sensors in the vehicle which in turn rely commands to the throttle and brakes of the vehicle to perform according to the adjacent vehicle’s distance. So cruise control is a system which provides comfort to drivers during long monotonous drives.

4

Acknowledgement I take this opportunity to express my deep sense of gratitude to my guide Prof. Vandana

Shah for her guidance, help, suggestion and supporting me to clear my doubts during the preparation of seminar and inspiring me to put my best efforts. I will be falling in my duty, if I don‘t offer my gratitude towards faculty members of electronics & communication department who helped me time to time to understand my topic and the various related areas. Last but not least, Acknowledgement will not be over without mentioning a word of thanks to all my friends & colleagues who helped me directly or indirectly in all the way through my seminar preparation.

Harshad S. Patel

INDEX 5

1. INTRODUCTION……………………………………………………………… 2. WHAT IS CRUISE CONTROL………………………………………………... 2.1 HOW TO SET CRUISE CONTROL…….…………………………………. 3. ADAPTIVE CRUISE CONTROL……………………………………………… 4. PARTS AND WORKING………………………………..……………………… 4.1 MILLIMETER-WAVERADAR………………………….………………… 4.2 STEREO AMERA…………………………………………….……………. 4.3 IMAGE PROCESSOR……….…..………………………………………… 4.4 FUSION PROCESSOR……..……..……………………………………….. 4.5 HEADWAY CONTROL UNIT………….……………………….………... 5. FUTURE ASPECTS………………...…………………………………………. 6. DANGERS OF CRUISE CONTROL…………………………………………. 7. SUMMERY….………………………………………………………………… 8. REFERENCES…………………………………………………………………

1.Introduction 6

Every minute, on average, at least one person dies in a crash. If you read this article from start to finish 30 or more deaths will have occurred across the globe by the time you are done. Auto accidents will also injure at least 10 million people this year, two or three million of them seriously. All told, the hospital bills, damaged property and other costs will add up to 1 - 3 % of the world’s gross domestic product according to the Paris based organization for economic cooperation and development. And, of course, the losses that matter most is not even captured by these statistics, because there is no way to put a dollar value on them. Engineers have been chipping away at this staggering numbers for a long time. Many safety innovations in the areas of banking systems, air bags, seat belts, body structures, steering and suspension have had a beneficial effect. Air bags and seat belts save tens of thousands of people a year by preventing their head from crashing into the windshield. Supercomputers now let designers create car frames and bodies that protect the people inside by absorbing much of energy of crash as possible. As a result, number of fatalities per million kilometres of vehicle travel has decreased. But the ultimate solution and the only thing that will save far more lives, limbs and money are to keep out cars from smashing into each other in the first place. That is exactly what engineers in the United States, Europe and Japan are trying to do. They are applying advanced microprocessors, radars, high-speed ICs and signalprocessing chips and algorithms in R&D programs that mark an about face in the automotive industry: from safety systems that kick in after an accident occurs, attempting to minimize injury and damage, to ones that prevent collisions altogether. The first collision avoidance features are already on the road, as pricey cruise control options on a small group of luxury cars. Over the next few years, these systems will grow more capable and more widely available, until they become standard equipment on luxury vehicles. Meanwhile, researchers will be bringing the first cooperative systems to market. This will take active safety technology to the next level, enabling vehicles to communicate and coordinate responses to avoid collisions. Note that to avoid liability claims in the event of cars equipped with cruise control systems, manufacturers of these systems and the car companies that use them are careful not to refer them as safety devices. Instead they are being marketed as driver aids, mere convenience made possible by latest innovative technology.

2.WHAT IS CRUISE CONTROL 7

Cruise control is a system, which automatically controls the speed of an automobile. The driver sets the speed and the system will take over the throttle of the car to maintain the speed. The system is thereby improving driver comfort in steady traffic conditions. In congested traffic conditions where speeds vary widely these systems are no longer effective. Most cruise control systems don’t allow the use of cruise control below a certain speed. The use of cruise control would be significantly increased if the vehicle speed could automatically adapt to the traffic flow. This feature can be handy for long drives along sparsely populated roads and usually results in better fuel efficiency. It is also known in some places as “poor man’s radar detector”, as by cruise control, a driver who otherwise tends to unconsciously increase speed over the course of a highway journey may avoid a speeding ticket. Blind inventor and mechanical engineer Ralph teeter invented cruise control in 1945. His idea was born out of the frustration of riding in a car driven by his lawyer, who kept speeding up and slowing down as he talked. The Chrysler Corporation on the 1958 Chrysler imperial introduced first car with cruise control systems.

2.1 HOW TO SET CRUISE CONTROL In modern designs, the cruise control may or may not need to be turned on before use – in some designs it is always “on” but not always enabled. Most designs have a separate “on” switch, as well as set, resume, accelerate and coast functions. The system is operated with controls easily within the driver’s reach, usually with two or more buttons on the steering wheel or on the windshield wiper or turn signal stalk. The cruise switches of a latest Ford car are shown in the figure below.

Fig 3.1

8

Driver should bring the car to speed manually and then use a button to set cruise control to the current speed. Most systems do not allow the use of cruise control below a certain speed to discourage use in city driving. The car will maintain that speed by actuating the throttle. Most systems can be turned off both explicitly or automatically, when the driver hits the brake or clutch. When the cruise control is in effect, the throttle can still be used to accelerate the car, although the car will then slow down until it reaches the previously set speed.

Fig 3.2 Control Buttons Now let us see the individual functions of each cruise switches in detail. 1.

The on and off buttons really don’t do much. Some cruise controls don’t have these buttons; instead, they turn off when the driver hits the brakes, and turn on when the driver hits the set button.

2.

The set/accelerate button tells the car to maintain the speed you are currently driving. If you hit the set button at 45 km/hr, the car will maintain your speed at 45 km/hr. holding down the set/accelerate button will make the car accelerate. On most cars, tapping it once will make the car go 1 km/hr faster.

3.

If recently disengaged the cruise control by hitting the brake or clutch pedal, hitting the resume button will command the car to accelerate back to the most recent speed setting.

9

4.

Holding down the coast button will cause the car to decelerate, just as if you took your foot completely off the gas. On most cars, tapping the coast button once will cause the car to slow down by 1 km/hr.

5.

The brake pedal and clutch pedal each have a switch that disengages the cruise control as soon as the pedal is pressed. So you can disengage the cruise control with a light tap on the brake or clutch.

10

3.ADAPTIVE CRUISE CONTROL There is a new type of cruise coming onto the market called adaptive cruise control. Two companies, TRW and Delphi Automotive Systems are developing a more advanced cruise control that can automatically adjust a car’s speed to maintain a safe following distance. Adaptive cruise control is similar to conventional cruise control in that it maintains the vehicle’s pre-set speed. However, unlike conventional cruise control, this new system can automatically adjust speed in order to maintain a proper and safe distance between vehicles in the same lane. These adaptive cruise control (ACC) systems, which add $1500 to $3000 to the cost of a car uses laser beams or forward looking radars to measure the distance from the vehicle they are in to the car ahead and its speed relative to theirs. If a car crosses into the lane ahead or if the lead vehicle slows down, say, and the distance is now less than the preset minimum (typically a 1 or 2 second interval of separation) or if another stationary object is detected, the system applies brakes, slowing down the vehicle, until it is following at the desired distance. If the leading car speeds up or moves out of the lane, the system opens the throttle until the car has returned to the cruise control speed set by the driver. In May 1998, Toyota became the first to introduce an ACC system on a production vehicle when it unveiled a laser-based system for its progress compact luxury sedan, which it sold in Japan. Then Nissan followed suit with a radar-based system, in the company’s Cima 41LV-2, a luxury sedan also sold only in Japan. In September 1999, Jaguar began offering an ACC for its XKR coupes and convertibles sold in Germany and Britain. Delphi Delco Electronic Systems supplies the radar sensing unit; TRW Automotive Electronics, the brake control; and Siemens, the assembly that manipulates the throttle. Last fall, Mercedes-Benz and Lexus joined the adaptive cruise control movement. Lexus offers an ACC option for its top-of-the-line LS430; at the movement, it is the only ACC system available in the United States. Mercedes’ system is an option on its C-Class and S-Class models, which are available in Europe.

11

Fig 3.1 Detection of Vehicle Edges By The Fusion Sensor All of the ACC systems available today are built around sensors that detect the vehicle ahead through the use of either radar or lidar (light detecting and ranging, the laser based analog to radar). The choice of sensors presents classic design tradeoffs. We will see the radar-based system in detail later. Lidar is less expensive to produce and easier to package but performs poorly in rain and snow. The light beams are narrower than water droplets and snowflakes, pushing down the signal-to-noise ratio in bad weather. Another problem is that accumulations of mud, dust or snow on the car can block lidar beams. At present, only one automaker, Lexus, uses a laser-based ACC system, in its LS430 luxury sedan. System engineers have acknowledged lidar’s shortcomings and taken steps to make the system unavailable in situations where the weather may limit its effectiveness. According to the LS430 owner’s manual, the system will automatically shut itself off if the windshield wipers are turned to a rapid setting, indicating heavy rain or snow; if something activates the anti-lock braking system (which helps the driver maintain a steering control and reduces stopping distances during emergency braking

12

situations); or if the vehicle skid control system detects the slipping of tires on turns that is common in wet weather.

Fig 3.2 The Lexus LS430 laser sensor built into the front grille

13

4.PARTS AND WORKING We have already seen the working of a laser-based ACC system, its limitations and all. Now let us take a look at how radar-based ACC system works, in detail. The main components of a typical radar-based ACC system are the following. 1.

Fusion sensor

2.

Headway control unit

3.

Throttle

4.

Brake

5.

Dashboard display

Fusion sensor is a combination of sensors and processors. The fusion sensor consists of the following components. 1.

Millimeter-wave radar

2.

Stereo camera

3.

Image processor

4.

Fusion processor

Fig 4.1 Architecture of a radar-based ACC system

14

Let us take a close look at each of these components, their individual roles, in detecting hazards in the roadway and responding in the correct manner so as to avoid those detected hazards. 4.1 MILLIMETER-WAVE RADAR Fundamental to any cruise control system is a sensor that can reliably detect obstacles in the traffic environment in a variety of conditions. Millimeter-wave radar is a method used for detecting the position and velocity of a distant object. This radar has a forward-looking range of up to 500 feet. The radar unit is housed behind the radiator grille. Every 60 milliseconds, the sensor sends out a trio of overlapping beams of electromagnetic radiations of approximately 3 degrees each (roughly the width of one traffic lane). The beam runs up to 500 feet ahead of the vehicle, and the sensor receives signals that are reflected back from objects in the roadway. Velocity and range is derived, by measuring the Doppler frequency shift and time of flight of transmission. Range is calculated using the formula C = 2*R/T Where ‘C’ is the velocity of light ‘R’ is the range ‘T’ is the time of flight of transmission. This information is then fed into a microprocessor (fusion processor) inside the passenger compartment. A major advantage of radar is that the performance is not affected by the time of the day, and therefore no driver adaptation is required for nighttime driving. The performance advantages of radar over other sensors are enhanced during poor weather conditions. Systems that rely on visible light are known to suffer significantly in the very conditions for which they are relied upon the most. Experience of radar operations has shown that reliable results can be obtained, even in inclement weather conditions. Radar-based systems can “see” at least 150 meters ahead in fog or rain, heavy enough to cut the driver’s ability to see down to 10 meters or less.

15

4.2 STEREO CAMERA The camera’s function is the same, as that of the radar, detection of cars and other objects in the roadway. Camera view reaches to a distance of 60 meters ahead of the vehicle. The stereo camera is situated by the rear view mirror. The camera view produces good lateral image, but it is unable to provide good estimates of range. The lane markings on the road are also detected by processing images from the camera. The image is then sent to the image processor. 4.3 IMAGE PROCESSOR The image-processing unit acts as an intermediate between the stereo camera and the fusion processor. It is also situated by the rear view mirror, along with the stereo camera. What image-processing unit is doing is that, it processes the images from the stereo camera and the data is then fed into the fusion processor. 4.4 FUSION PROCESSOR The function of fusion processor is termed as Data Fusion. Data fusion is a collection of techniques for combining the measurements from more than one sensor to provide a more unified result. This has several benefits. 

The overall estimates of parameters can be more accurate than for individual sensor estimate, as they reinforce each other.



Any parameter need not depend on one sensor alone. This has benefits of Fault Tolerance by allowing redundancy to be introduced into the system. For example, if the system had infrared and video based sensors, it could survive the failure of either of these and continue to function although accuracy and performance in certain conditions can be reduced. The fusion processor receives information from the two sensors, millimeter-wave

radar and stereo camera. The data contains information like lane path, vehicle speed, range etc relative to host vehicle. The video produces good lateral image, but it is not able to provide good estimate of range. The radar conversely produces good estimates of range and hence good relative velocity estimates, but has poor lateral positional accuracy. Thus by fusing data from these two sensors the object position can be localized to a better accuracy by considering the intersection of the two areas of positional uncertainty generated by each sensor.

16

Another possible benefit of data fusion is that of object identification, by combining the expected responses of an object in the sensors. For example, the image processing may confuse a stationary pedestrian and a traffic sign, especially at longer ranges, as they both are tall, thin objects. However fusing data would allow an unambiguous decision to be reached immediately as the two objects have radically different radar responses. 4.5 HEADWAY CONTROL UNIT Having detected a hazard the system must respond in the most appropriate manner so as to avoid the hazard. Evidence suggests that a small reduction in driver reaction time will dramatically reduce the number of accidents. This can be achieved by intervening with the controls of the vehicle. Headway control unit takes up this job. Headway control unit has control on the brakes and throttle. Headway control unit makes necessary adjustments to the brakes and throttle that would allow maintaining a constant and safer distance behind the vehicle in front. In addition to all these, if a suddenly stopped vehicle or a large object in the roadway or even a bend in the road is detected, a red triangle flashes on the dashboard, warning the driver. Then the driver must stop the vehicle by applying brakes manually in the first two cases and steer the vehicle in the third case.

Fig 4.2 A Prototype of a Car with Fusion Sensor Arrangement

17

FUTURE ASPECTS Though conventional cruise control is still an expensive novelty, the next generation, called co-operative adaptive cruise control, or CACC, is already being tested in California and elsewhere. While ACC can only respond to a difference between its own speed and the speed of the car ahead, cooperative systems will two or more cars to communicate and work together to avoid a collision. Ultimately, experiments say, the technology may let cars follow each other at intervals as short as half a second. At 100 km/hr, that would amount to a distance between cars of less than 14 meters (roughly two car lengths).

Fig 5.1 Meanwhile at Fujitsu Ten Ltd, Japan, engineers are working towards another vision of the future of adaptive cruise control-one targeted squarely at the realities of driving on often-congested urban and suburban highways. Fujitsu Ten has demonstrated a prototype system for so called stop-and-go adaptive cruise control. Ordinary ACC systems maintain a safe distance between cars at speeds above 40 km/hr, whereas Fujitsu Ten’s system will work primarily at lower speeds in heavy traffic. If the car in front stops, it will bring a vehicle to a complete stop. Afterward, it will not re-engage the throttle-that’s up to the driver-but as soon as the throttle is engaged, it will accelerate and decelerate along with the leading car over any range of speeds between zero and the cruising speed set by the driver.

18

Within a decade or so, the drivers of the most advanced cars will only have to steer. Eventually, people might not be even entrusted with that task, at least on limited access highways.

19

DANGERS OF CRUISE CONTROL The only danger with cruise control is the use of cruise control in wet and slippery roads. You should turn off cruise control while driving through such conditions. It is very dangerous to use cruise control in any slippery conditions like rain, snow, or ice as it takes the complete control of the vehicle out of your hands. That is because most cruise control systems are designed for normal dry conditions and can’t sense whether the wheels are spinning uselessly. If your car begins to careen out of control, cruise control will continue to accelerate as it tries to maintain a constant speed. It would put your car into a sideway spin cause the vehicle to flip over.

Fig

20

SUMMERY This seminar has described about the cruise control systems that are commonly seen in luxury cars now a day. Fully autonomous car is probably not viable in the foreseen future. The Intelligent Vehicle Initiative in the United States and Ertico program in Europe are among dozens of groups working on technologies that may ultimately lead to vehicles that are wrapped in a cocoon of sensors, with a 360 view of their environment. Then nearby vehicles would be in constant communication with each other and act co-operatively, enabling groups of cars to race along like train cars, almost bumper to bumper, at speeds above 100 km/hr. It will probably take decades, but car accidents may eventually become almost as rare as plane crashes are now. The automobile, which transformed the developed world by offering mobility and autonomy, will finally stop exacting such an enormous cost in human lives.

REFERENCE 21

22