8000 INM SR6.0 Third Party HW & SW Requirements...
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 76.8060-70222D 09.12.2014
Document Information
Revision Revision History Document No.
Date
Description of Changes
76.806 76.8060-7 0-70222 0222D D
09.12.2 09.12.2014 014
mTera mTera UTP added added in chapter chapterss 2.3, 2.3, 2.4, 2.8, 2.8, 2.9, 2.9, 5.1.3 5.1.3 and 5.4. 5.4. Product family limitation in DSC removed from chapter 2.9. Linux support for 5500 added in chapter 2.4 and the 5500 data modified in chapter 5.4. OpenSwitch OpenSwitch Server data added in chapter 5.1.4. Sybase Replication Replication Server and Sybase OpenSwitch OpenSwitch Server tables added in chapter 5.1.6. Chapter 5.4.5 OpenSwitch Server Software and chapter 5.4.6 Replication Server Software added.
76.8 76.806 0600-70 7022 222C 2C
07.1 07.10. 0.20 2014 14
Hot Standby Standby data added in chapter chapterss 2.2.2 and and 4. 8615 Smart Router added in the Recommendation for Maximum Number of Node s pe r Commu nication Server table in cha pter 2.3. Sybase ASE 15.7 version updated to SP122 in chapter 5.4.3.
76.8 76.806 0600-70 7022 222B 2B
11.07 1.07.2 .201 014 4
The document document has been been rebranded rebranded.. Windows 8.1 support for a workstation added in chapters 1, 5.2, 5.3, 5.4 and 5.4.1. Configuration definitions modified in chapter 1. 8115 NTU and 8155 Access Switch added in the Recommendation Recommendation for Maximum Number of Nodes per Communication Communication Server table in chapter 2.3 and 8100 EFM added in chapters 2.3, 2.5 and 5.1.3. Numbers in the SSC and DSC data modified in chapters 2, 2.8 and 2.9. A note on 6300 Craft Terminal not being supported in SSC added in chapter 2.8 and 6300 Adapter notes modi fied in chapters 2.3 and 5.4.2. Minimum required disk space per user with ThinClient user data added in chapter 5.1.6. A note on Eiconcard limitation in Windows Server 2012 removed removed and V6R10 added in chapter 5.1.7. Sybase ASE 15.7 version updated to SP110 SP110 in chapter 5.4.3. 5.4.3. ThinClient Server version updated to Citrix XenApp 7.5 and the operating operating system data to Windows Windows Server 2012 R2 in chapter 5.4.4.
© 2014 Coriant. All rights reserved. reserved. treaties. Your right to use this manual is This manual is protected by U.S. and internati onal copyright laws, conventions and treaties. subject to limitations and restrictions imposed by applicable licenses and copyright laws. Unauthorized reproduction, modi fication, distribution, display or other use of this ma nual may result in criminal and civil penalties. The speci fications and information regarding the products in this manual are subject to change without notice. All statements, information, and recommendations in this manual are believed to be accurate but are presented without warranty of any kind, express or implied. Users must take full responsibility for their application of any products. Adobe ® Reader ® are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 2
76.8060-70222D © 2014 Coriant.
Document Information
Revision Revision History Document No.
Date
Description of Changes
76.806 76.8060-7 0-70222 0222D D
09.12.2 09.12.2014 014
mTera mTera UTP added added in chapter chapterss 2.3, 2.3, 2.4, 2.8, 2.8, 2.9, 2.9, 5.1.3 5.1.3 and 5.4. 5.4. Product family limitation in DSC removed from chapter 2.9. Linux support for 5500 added in chapter 2.4 and the 5500 data modified in chapter 5.4. OpenSwitch OpenSwitch Server data added in chapter 5.1.4. Sybase Replication Replication Server and Sybase OpenSwitch OpenSwitch Server tables added in chapter 5.1.6. Chapter 5.4.5 OpenSwitch Server Software and chapter 5.4.6 Replication Server Software added.
76.8 76.806 0600-70 7022 222C 2C
07.1 07.10. 0.20 2014 14
Hot Standby Standby data added in chapter chapterss 2.2.2 and and 4. 8615 Smart Router added in the Recommendation for Maximum Number of Node s pe r Commu nication Server table in cha pter 2.3. Sybase ASE 15.7 version updated to SP122 in chapter 5.4.3.
76.8 76.806 0600-70 7022 222B 2B
11.07 1.07.2 .201 014 4
The document document has been been rebranded rebranded.. Windows 8.1 support for a workstation added in chapters 1, 5.2, 5.3, 5.4 and 5.4.1. Configuration definitions modified in chapter 1. 8115 NTU and 8155 Access Switch added in the Recommendation Recommendation for Maximum Number of Nodes per Communication Communication Server table in chapter 2.3 and 8100 EFM added in chapters 2.3, 2.5 and 5.1.3. Numbers in the SSC and DSC data modified in chapters 2, 2.8 and 2.9. A note on 6300 Craft Terminal not being supported in SSC added in chapter 2.8 and 6300 Adapter notes modi fied in chapters 2.3 and 5.4.2. Minimum required disk space per user with ThinClient user data added in chapter 5.1.6. A note on Eiconcard limitation in Windows Server 2012 removed removed and V6R10 added in chapter 5.1.7. Sybase ASE 15.7 version updated to SP110 SP110 in chapter 5.4.3. 5.4.3. ThinClient Server version updated to Citrix XenApp 7.5 and the operating operating system data to Windows Windows Server 2012 R2 in chapter 5.4.4.
© 2014 Coriant. All rights reserved. reserved. treaties. Your right to use this manual is This manual is protected by U.S. and internati onal copyright laws, conventions and treaties. subject to limitations and restrictions imposed by applicable licenses and copyright laws. Unauthorized reproduction, modi fication, distribution, display or other use of this ma nual may result in criminal and civil penalties. The speci fications and information regarding the products in this manual are subject to change without notice. All statements, information, and recommendations in this manual are believed to be accurate but are presented without warranty of any kind, express or implied. Users must take full responsibility for their application of any products. Adobe ® Reader ® are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 2
76.8060-70222D © 2014 Coriant.
Document Information
Terms and Conventions Conventions
76.8060-70222D © 2014 Coriant.
Term
Explanation
CPU
Central Processing Unit
DCN
Data Control Network
DNS
Domain Name Service
DSC
Dual Server Con figuration
IP
Internet Protocol
LAN
Local Area Network
NMRS
Network Management Resilience Service
NTP
Network Time Protocol
NTU
Network Terminating Unit
PMS PMS
Perf Perfor orm mance ance Mana Manage geme ment nt Syst System em
RAID RAID
Redu Redund ndan antt Arra Array y of Inex Inexpe pens nsiv ivee Disk Diskss
RAM
Random Access Memory
SSC
Single Server Con figuration
TCP TCP
Trans ransmi miss ssio ion n Contr ontro ol Prot Protoc ocol ol
WINS WI NS
Windo indows ws Inte Intern rnet et Nami Naming ng Serv Servic icee
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 3
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 4
76.8060-70222D © 2014 Coriant.
Table of Contents
Table of Contents
About the Manual .............................................................................................................. 7 Objectives ........................................................................................................ ............................................................... Audience.......................................................................... ............................................................................................... Related Documentation ................................................................................................. ................................................. Document Conventions ................................................................................................................... ............................... Product Name Rebranding .............................................................................................................. ............................... Documentation Feedback .................................................................................................. .............................................
7 7 7 7 8 8
1
General ......................................................................................................................... 9
2
8000 Intelligent Network Manager System Configurations.....................................11 2.1 2.2
2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10
3
DCN, LAN and LAN-IC Requirements........................................................................19 3.1 3.2 3.3 3.4
4
8000 Intelligent Network Manager Workstation ................................................................................................. 13 Database Server .................................................................................................................... ............................... 13 2.2.1 Separate Performance Database with Partitioning .............................................................................. 13 2.2.2 Replication Server ............................................................................................................................... 14 Communication Server ........................................................................................... ............................................. 14 Management Server .............................................................................................................. ............................... 15 DXX Server (8100 Adapter)....................................................................................... ......................................... 16 Recovery Server ........................................................................................... ....................................................... 16 8100 Service Computer .......................................................................................................... ............................. 16 Single Server Configuration ................................................................................................................................ 17 Dual Server Configuration - 8000 Intelligent Network Manager........................................................................ 17 8000 Intelligent Network Manager ThinClient Solution..................................................................................... 18
DCN...... .................................................................................................................. ............................................. 19 LAN Configuration.............................................................................................................................................. 20 LAN and LAN-IC......................................................... ....................................................................................... 21 Networking Configuration................................................................................................................................... 22
Database Protection Levels ....................................................................................... 23
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 5
Table of Contents
5
Computer Requirements for 8000 Intelligent Network Manager.............................26 5.1
5.2 5.3 5.4
5.5 5.6
RAM, CPU and Disk Requirements ................................................................................................................... 26 5.1.1 Single Server Configuration ................................................................................................................ 27 5.1.2 Dual Server Configuration................................................................................................................... 27 5.1.3 Multi-server Configuration ......................................................................................................... ......... 27 5.1.4 Network Manager Resilience Service Hardware Requirements ......................................................... 29 5.1.5 Disk Requirements for Workstations................................................................................................... 29 5.1.6 Disk Requirements for Servers............................................................................................................ 29 5.1.7 Accessories Needed for Servers .......................................................................................................... 32 Minimum Requirements for Service Computers ................................................................................................. 33 Minimum Requirements for Workstations .......................................................................................................... 34 Software Sets ........................................................................................................................ ............................... 34 5.4.1 Workstation Software ................................................................................................... ....................... 35 5.4.2 Server Software – Management Server and Communication Server.................................................. 35 5.4.3 Database Server Software.................................................................................................................... 35 5.4.4 ThinClient Server Software................................................................................................................. 36 5.4.5 OpenSwitch Server Software............................................................................................................... 36 5.4.6 Replication Server Software................................................................................................................ 36 5.4.7 VMware............................................................................................................................................... 36 Displays ............................................................................................................ ................................................... 36 Preinstalled Computers... ...................................................................................................... ............................... 37
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 6
76.8060-70222D © 2014 Coriant.
About the Manual
About the Manual Objectives This manual describes all the needed third party software components and versions (operating systems and software versions) in the 8000 Intelligent Network Manager system. It also describes the relevant requirements and recommendations of the 8000 Intelligent Network Manager system.
Audience This manual is intended for system administrators and system specialists.
Related Documentation The document numbering scheme consists of the document ID, indicated by numbers, and the document revision, indicated by a letter. The references in the Related Documentation table below are generic and include only the document ID. To make sure the references point to the latest available document versions, please refer to the relevant product document program on the Tellabs and Coriant Portal by navigating to www.portal.tellabs.com > Product Documentation > Data Networking > 8000 Intelligent Network Manager > Technical Documentation. 8000 Intelligent Network Manager SR6.0 Software Installation Manual (76.8060-70201)
Provides instructions on installing and configuring 8000 Intelligent Network Manager in different computer platforms (workstation, servers).
8000 Intelligent Network Manager SR6.0 Installation and Configuration Guide for Management Server and Recovery Server (76.8060-70202)
Provides instructions on installing and configuring 8000 Intelligent Network Manager Management Server and Recovery Server.
Web Reporter for 8000 Intelligent Network Manager SR6.0 Installation and Configuration Manual (76.8060-70215)
Provides instructions on installing and configuring the Web Reporter tool.
8000 Intelligent Network Manager SR6.0 Installation and Configur ation Guide for Northbound Interface (76.8060-70204)
Provides instructions on installing and configuring the Northbound Interface in 8000 Intelligent Network Manager.
Document Conventions This is a note symbol. It emphasizes or supplements information in the document.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 7
About the Manual
This is a caution symbol. It indicates that damage to equipment is possible if the instructions are not followed.
This is a warning symbol. It indicates that bodily injury is possible if the instructions are not followed.
Product Name Rebranding Product names are being rebranded and as a result the product name format consists of a numerical identifier and a descriptive part. Additionally, the previous Tellabs 7300 product family is renamed and the individual product names are also changed. The table below lists previous and new product names. You may see instances of both the previous and the new product names in the customer documents during the transition period to the new naming system. Previous Product Name
New Product Name
Tellabs ® 7300 metro Ethernet switching series
7090 Packet Transport Platform Series
Tellabs ® 7305
7090-05 CE
Tellabs ® 7307
7090-07 CE
Tellabs ® 7310
7310
Tellabs ® 7325
7090-25 CE
Tellabs ® 7345
7090-45 CE
Documentation Feedback Please contact us to suggest improvements or to report errors in our documentation: Email:
fi
[email protected]
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 8
76.8060-70222D © 2014 Coriant.
1 General
1
General 8000 Intelligent Network Manager (8000 INM) SR6.0 has been designed to use Windows 7, Windows 8.1, Windows Server 2008, Windows Server 2012 and Red Hat Enterprise Linux and Sybase Adaptive Server Enterprise relational database. With this design it is possible to build a flexible system that easily adapts to changes in a managed network and to changes in the organization of network management tasks. The supported 8000 INM system configurations are listed in the following. • Single Server Configuration (SSC) • Small and medium-sized networks with a limited number of users • Dual Server Configuration (DSC) • Medium-sized networks • Multi-server Configuration • Scalable configuration to meet various network and operation requirements For more detailed information on the different supported con figurations, refer to 8000 Intelligent Network Manager Software Installation Manual. 8000 Intelligent Network Manager can adapt to centralized or distributed management schemes, and can grow when the needs of an operator develop. An operator can minimize startup costs in a smaller Coriant network by managing their entire network with a single server system con figuration. When the needs of an operator and their network grow, new management workstations and servers can be added at any time to build up to a multi-server 8000 INM system con figuration.
8000 Intelligent Network Manager may work on other types of machine con figurations than the speci fied ones, but it cannot be guaranteed. The requirements in this document apply to new purchases only. Coriant also requires existing customers to follow up with this document. When planning to change some part of the 8000 INM system con figuration, it is to be done according to the requirements of this document. Check that you always use the most recent version of this document. Before updating the 8000 INM system, contact Coriant Customer Services.
It is recommended to use the latest version of the Norton (Symantec) antivirus program in your workstations and servers. Norton may affect the performance of servers.
8000 Intelligent Network Manager has been designed and tested to be the only application running on the computers. Running other applications on the same computers is not supported and Coriant strongly recommends against it.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 9
1 General
A support agreement for the third party hardware and software components is highly recommended.
It is the responsibility of the end customer to ensure their compliance to the third party licensing terms and conditions.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 10
76.8060-70222D © 2014 Coriant.
2 8000 Intelligent Network Manager System Con fi gurations
2
8000 Intelligent Network Manager System Configurations In the 8000 Intelligent Network Manager system con figurations, the network manager components are distributed over several computers (some optional). • Workstation(s) • Database Server • Communication Server(s) • Management Server(s) • DXX Server(s) • Recovery Server(s) • 8100 Service Computer 8000 INM can be con figured depending on the size of the network, the number of concurrent users and the type of nodes used. The different supported con figurations are described in 8000 Intelligent Network Manager Software Installation Manual . As an example the 8000 INM components in a multi-user environment is shown in the fi gure below.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 11
2 8000 Intelligent Network Manager System Con fi gurations
Fig. 1
Example of Multi-user 8000 INM Con fi guration
It is recommended that all the 8000 Intelligent Network Manager server computers (Database Server, Communication Servers, Management Servers, DXX Servers and Recovery Server) are located in the same LAN segment to provide a more reliable operation. However, 8000 INM workstations can be distributed to different locations using routers. For more information, refer to the hardware and software requirements in chapter 5 Computer Requirements for 8000 Intelligent Network Manager . The recommendation of the maximum number of workstations is based on the Coriant evaluation of the 8000 INM system performance. Con figuration of the servers and workstations and the DCN network is required to ful fill at least the minimum requirements of the large networks described in chapters 3 DCN, LAN and LAN-IC Requirements and 5 Computer Requirements for 8000 Intelligent Network Manager . Several internal and external factors such as the functions utilized for provisioning and the amount of collected PMS data set memory and CPU capacity requirements for the system. Additionally, the quality of DCN and the number of managed nodes may affect the overall performance of the system and the total maximum number of workstations can vary. The tables below show the recommendations for the maximum number of workstations and the maximum number of workstations per server.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 12
76.8060-70222D © 2014 Coriant.
2 8000 Intelligent Network Manager System Con fi gurations
Recommendation for Maximum Number of Workstations Maximum Number of Workstations Workstation
1501
Recommendation for Maximum Number of Workstations per Server Type of Server
Maximum Number of Workstations
Management Server
40
ThinClient Server
20
Single Server Configuration
10
Dual Server Configuration
10
A maximum of 30 000 Coriant network elements is supported. When calculating the number of network elements in the system, the number of other objects may also have an impact on the required hardware. For example, it is supposed that there are on average 5 Network Terminating Units (NTUs) per node. If you have more than 5 NTUs per node, use the following formula: number of NTUs/5 = number of nodes. For example, if you have a network with 1 000 nodes and there are 10 000 NTUs, the requirements will be as for a network with 2 000 nodes. Additionally, the 8800 NEs can be very dense and should b e counted as 5 nodes for 8830 Smart Router and 8840 Smart Router, and 10 nodes for 8860 Smart Router.
2.1
8000 Intelligent Network Manager Workstation 8000 Intelligent Network Manager workstation functions as an access point to an 8000 INM system network and its elements for a remote operator through a graphical user interface. There is only one workstation type. However, workstation software can be run also in Management Server computer. Workstation connects to a Management Server running a Satellite Service. Note that the workstation can only be run on the Management Server with Windows as the operating system and thus, workstation is not supported on Linux.
2.2
Database Server The database hardware requirements vary according to the actual size of the 8000 Intelligent Network Manager system network. Sybase database is supported on Windows and Linux servers. Solaris is only supported for the existing customer installations.
2.2.1
Separate Performance Database with Partitioning Separate performance database (PM DB) with partitioning is a scalability enhancement to the 8000 Intelligent Network Manager system. It increases the ef ficiency of the PM application and Network Manager Resilience Service. Furthermore, as a result of separation, it protects the 8000 INM configuration database from fi lling up due to high amount of PMS data.
1In
case of pure 8100 network, the maximum number of workstations is 800.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 13
2 8000 Intelligent Network Manager System Con fi gurations
It is recommended to consider taking separate PM DB with partitioning into use, if the daily collected amount of PM data exceeds 10 million rows. Furthermore, if some of the following conditions are met in a customer network, it is strongly recommended that separate PM DB with partitioning is taken into use. 1.
The performance data deletion time exceeds two hours.
2.
Administrative burden is introduced by: • Database size being too large for ef ficiently taking database backups. • Database size constantly approaching its limits and introducing need for DB size increments or size monitoring. • Replication latency is over the desired switch over time period.
3.
Customer perceives PM reports being too slow.
These conditions are meant to act as guidelines and their applicability towards an individual customer network might vary. The guidelines have been established based on customer cases and testing. Note that a separate performance database requires an additional Sybase partitioning license per Database Server.
2.2.2
Replication Server Replication Server handles the replication from primary to secondary database in the Network Manager Resilience Service (NMRS) Warm or Hot Standby environment. In the 8000 Intelligent Network Manager system con figuration Linux Database Servers must be used. There are recommendations for general guidelines in chapter 5.1.4 Network Manager Resilience Service Hardware Requirements, but optimal server speci fications must be carried out based on a specific network.
When planning a Network Manager Resilience Service, contact your Coriant representative. Before purchasing any Network Manager Resilience Service, the exact supported software version numbers and the latest details need to be checked from Coriant.
2.3
Communication Server Communication Server is used for managing 5500, 6300, 7090, 7100, 8100 EFM, 8600, 8800 and mTera UTP network elements. Communication Server is supported on Windows. Linux server is supported for the 5500, 7090, 7100 and mTera UTP network elements. The number of required Communication Servers depends on the size of the network. A recommendation for a maximum number of nodes per a single Communication Server is presented in the table below. Each server takes care of one or several areas in a network and can run several parallel adapters (e.g. 7090, 7100, 8600 and 8800). It is recommended to run the adapters in separate Communication Servers, especially if the number of managed network elements is signi ficant. MARBEN TM OSIAM OSITP4, version 1.2 is used for the 6300 network element communication.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 14
76.8060-70222D © 2014 Coriant.
2 8000 Intelligent Network Manager System Con fi gurations
6300 Adapter is only supported in Windows Server 2008.
Recommendation for Maximum Number of Nodes per Communication Server Node Type
Number of Nodes per Communication Server
5500 nodes, or
50
6300 nodes, or
500
7090 nodes, or
500
7100 Nano, or
300
7100 OTS, or
100
mTera UTP, or
300
8115 NTU, or
5000
8155 Access Switch, or
500
8602 Smart Router, or
5000
8605 Smart Router, or
5000
8606 Ethernet Aggregator, or
2500
8607 Smart Router, or
3500
8609 Smart Router, or
3500
8611 Smart Router, or
2500
8615 Smart Router, or
2500
8620 Smart Router, or
3500
8630 Smart Router, or
500
8660 Smart Router, or
150
8800 Smart Routers
100
For example, a single Communication Server can handle up to 30 x 8660 Smart Routers and 4000 x 8605 Smart Routers with PMS. These recommendations are general guidelines for dimensioning the 8000 Intelligent Network Manager system. The optimum number of Communication Servers needed for a network depends on the number of nodes, the node inventories (the number and type o f physical and logical interfaces), the set of PMS counters monitored, the overall 8000 INM activity (operations per second in the network), the fault and performance polling targets etc.
2.4
Management Server The Management Server functions as a framework for different 8000 Intelligent Network Manager application logic divided into services each running processes of its own. The installation of the different service types is done by selecting the appropriate service for Management Server in 8000 Intelligent Network Manager Setup Wizard. Management Server is supported on Windows. Additionally, Linux server is supported for the 5500, 7090, 7100 and mTera UTP networks.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 15
2 8000 Intelligent Network Manager System Con fi gurations
Only one workstation can be run on the Windows Management Server.
For more information related to different services, refer to 8000 Intelligent Network Manager Installation and Con fi guration Guide for Management Server and Recovery Server .
2.5
DXX Server (8100 Adapter) DXX Server is used for managing 8100 network elements. However, note that Communication Server is used for managing the 8100 EFM network elements. Refer to 2.3 Communication Server . The number of required DXX Servers depends on the size of the network. Each server take s care of one or several areas in the network. Increasing the number of DXX Servers also increases the reliability of network management. In a DXX Server one X.25 port is required per 250 subracks. A DXX Server can have a maximum of four X.25 ports (using dual port X.25 cards), i.e. a total of 1000 subracks. Normally this means 700-800 nodes, depending on the number of 8170 Cluster Nodes. When using asynchronous links you can have two links with a maximum of approximately 50 subrack s per link, i.e. a total of 100 subracks. With four X.25 ports and two asynchronous links the total is 1100 subracks in a DXX Server. When using IP links you can have 250 subracks per IP link. A single DXX Server can handle up to 1500 subracks. If you have several NTUs (more than fi ve) per node, take into account that it can slow down fault polling if there are numerous faults in the NTUs. DXX Server with the X.25 card is not supported in a virtualized server environment.
2.6
Recovery Server The Recovery Server component is used for circuit and trunk protection. It is possible to have a second Recovery Server for backup purposes. The DXX Server and Recovery Server can be run in a common machine if the network size is up to approximately 350 nodes and there are no other DXX Servers in the network.
2.7
8100 Service Computer 8100 Service Computer (SC) is used for monitoring and controlling the operation of a single 8100 system node. The only 8000 Intelligent Network Manager user interface component installed on SC is Node Manager for the 8100 nodes. You can install the 6300 Craft Terminal which is used for controlling network elements of the 6300 system, in the same computer as the SC. If you use the serial port for communication, only one of the programs can be run at a time. If you use the IP link for the SC communication, Craft Terminal (using the serial port) can be run at the same time.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 16
76.8060-70222D © 2014 Coriant.
2 8000 Intelligent Network Manager System Con fi gurations
2.8
Single Server Configuration The Single Server Con figuration (SSC) for small networks is a system in which the Management Server, Communication Server and the database are all located in one physical entity. In the Windows operating system the management system con figuration supports up to ten users. The SSC is supported on Windows servers. Additionally, there is Single Server con figuration support for the 5500, 7090, 7100 and mTera UTP networks in Linux. However, running a workstation on the server itself is only supported in Windows. The maximum number of supported network elements is 30 per cent compared to a single Communication Server (refer to chapter 2.3 Communication Server ).
Fig. 2 Example of Single Server Confi guration
See the hardware and software requirements in chapter 5 Computer Requirements for 8000 Intelligent Network Manager .
6300 Craft Terminal is not supported in SSC.
2.9
Dual Server Configuration - 8000 Intelligent Network Manager The Dual Server Con figuration (DSC) is a setup with two physical servers in which the Database Server and Management Server are located on one physical server while the second one hosts the Communication Server. In the Windows operating system the management system con figuration supports up to ten workstations, out of whi ch one can be located on the combined Database and Management Server. The DSC is supported on Windows and Linux servers. There is Dual Server configuration support for the 5500, 7090, 7100 and mTera UTP networks in Linux. However, running a workstation on the server itself is only supported in Windows. The maximum number of supported network elements is the same as for a single Communication Server (refer to chapter 2.3 Communication Server ).
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 17
2 8000 Intelligent Network Manager System Con fi gurations
Fig. 3 Example of Dual Server Con fi guration
See the hardware and software requirements in chapter 5 Computer Requirements for 8000 Intelligent Network Manager .
2.10 8000 Intelligent Network Manager ThinClient Solution 8000 Intelligent Network Manager ThinClient is a solution that replaces the 8000 INM workstation with a client/server application which saves bandwidth, simpli fies upgrades and maintenance and provides fl exible remote access. The ThinClient solution is based on Citrix XenApp. ThinClient solution is not supported in Linux.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 18
76.8060-70222D © 2014 Coriant.
3 DCN, LAN and LAN-IC Requirements
3 3.1
DCN, LAN and LAN-IC Requirements DCN An inband or outband Data Control Network (DCN) can be used between 8000 Intelligent Network Manager and network elements. In the fi gure below a reference mobile transmission network is described for DCN dimensioning. For a typical network (as shown in the fi gure below), the recommended DCN bandwidths are at least as follows. • 10 Mbps to core nodes, • 1 Mbps to hub nodes (aggregating up to ten cell sites), and • 256 kbps to cell site nodes (128 kbps without PMS).
Fig. 4 Mobile Transmission Network
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 19
3 DCN, LAN and LAN-IC Requirements
3.2
LAN Configuration It is recommended that the LAN is dedicated to 8000 Intelligent Network Manager computers. When building an Ethernet LAN for 8000 INM, special attention should be paid to the connections between servers. A main management LAN interconnects the Database Server and various 8000 INM servers. Below is a fi gure of the main management LAN and some requirements for it. • Ethernet bandwidth of at least 100 Mbps is required. • Switch-based technology is required. • The main management LAN should be dedicated for use with 8000 INM only. • Tolerated maximum latency is 10 ms. • If the database is replicated, the network speed requirements for the replication database equal to the 8000 INM LAN.
Fig. 5
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 20
8000 INM Main Management LAN
76.8060-70222D © 2014 Coriant.
3 DCN, LAN and LAN-IC Requirements
There are some requirements for the LAN con figuration. • Workstation (previously satellite workstation) down-link • Segment(s) of LAN that interconnect remote workstations to the Management Server. • Hubs and switches can be used. • Every computer having a database connection (all servers) should have reliable and error free network connection. • Note that one such computer behind slow database connection will slow down the whole network management system. It is recommended not to use auto-negotiation for the speed and duplex settings in switch ports and server NICs on the 8000 INM LAN.
3.3
LAN and LAN-IC It is possible to connect workstations to servers from remote locations using TCP/IP. In such a case the communication link capacity between the locations should be as recommended in the following table. These capacities guarantee a reasonable workstation startup time, depending on the size of the network. It is assumed that only one workstation is started up at a time. Recommendations for communication link capacity between w orkstations and the main management LAN, based on workstation startup time Maximum Number of Network Elements in the Network
Minimum Communication Link Capacity
1000
512 kbps
> 1000
1 Mbps
> 10000
2 Mbps
> 30000
4 Mbps
The capacity should be reserved as speci fied above even if there is only one workstation in a remote location. However, if there are several workstations in a remote location, the link capacity must be set at least to the values listed in the following table. Recommendations for communication link capacity between workstations and the main management LAN, based on the number of workstations in remote LAN Number of Workstations in Remote Location
Minimum Communication Link Capacity
1-3
512 kbps
4-10
2 Mbps
11-20
4 Mbps
The capacity must be selected as the maximum of the capacities based on the workstation startup time and number of workstations in a remote location.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 21
3 DCN, LAN and LAN-IC Requirements
The communication links between the locations must be reliable, as the quality of these links shall be better than 99.99% in Error-Free Seconds. If the quality of communication links is worse than required, Coriant cannot guarantee that 8000 Intelligent Network Manager or its parts work ef ficiently.
3.4
Networking Configuration It is highly recommended to use the Windows domain network model when more than ten computers are used for network management. For ease of administration of the computers, the servers and workstations should be connected to a domain if there are more than ten computers in the management LAN. This should be done, especially, if users are using unique accounts to access the computers. In a Windows domain, the user accounts are stored centrally in one computer that does the user authentication. A workgroup model (Peer-to-Peer) network can be used if there are less than 10 computers in the management LAN, or if the users are using the same username and password. It is also recommended to have Windows Internet Naming Service (WINS) and/or Domain Name Service (DNS) servers running in the LAN. These servers provide name resolution services to other computers in the network, so that they can resolve computer names into an IP address that enables computers on a network to fi nd one another and transfer information. The name resolution services should not be running in any of the dedicated 8000 Intelligent Network Manager servers. Separate servers are needed. All servers must have fi xed IP addresses. It is highly recommended to enable Network Time Protocol (NTP) client service on the Database and Replication Servers as well as enable NTP in all 8600 network elements. Management and Communication Servers should use either NTP or Windows domain time service to keep the clocks synchronized.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 22
76.8060-70222D © 2014 Coriant.
4 Database Protection Levels
4
Database Protection Levels There are several ways of minimizing the data loss in case of Database Server failures. • Scheduled database dumps. You always need to take scheduled dumps of the database. Frequency of transaction dumps should be set according to the level of network activity. This also de fines the risk level in case of failures. Taking database dumps is the only way to restore the previous database state e.g. in case of human errors. • Mirrored disk drives. Mirroring provides protection against hard disk failures. It means using redundant disks in Database Server. • Clustering. Clustering protects the database from any single point of failure in Database Server. Clustering provides protection within one site. Note that this solution must be purchased directly from the server supplier. • Network Manager Resilience Service is currently available in Cold, Warm and Hot Standby. • Cold Standby means having an inactive spare Database Server with ready con figurations. • Warm Standby is a resilience service, which provides a way to manually con figure connections from the main database to the replicated backup database in a case of failure. • Hot Standby is a resilience service, which transfers connections from the main database to the replicated backup database automatically in a case of failure. The automatic transfer does not cause any traf fic outages. However, it can be noticed as a short delay in the 8000 Intelligent Network Manager usage.
When planning a Network Manager Resilience Service, contact your Coriant representative. Before purchasing any Network Manager Resilience Service, the exact supported software version numbers and the latest details need to be checked from Coriant.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 23
4 Database Protection Levels
Scheduled Database Dumps
Mirrored Disk Drives
Clustering
Cold Standby
Warm Standby
Hot Standby
Obligatory / optional
Obligatory
Obligatory
Optional
Optional
Optional
Optional
Distance between primary and backup server
Unlimited
Within the server
8 m - 15 km depending on the cable media
Unlimited
Unlimited with NMRS Warm Standby
Unlimited with NMRS Hot Standby
Failover: automatic / manual
Manual
Automatic
Manual
Manual
Manual
Automatic
Recovery time
Time of restoring the database dumps
Real time
Start-up time of the database software
Time of restoring the database dumps
Time of starting 8000 INM system, some latency depending on the connection between the servers
Real time, some latency depending on the connection between the servers
Backup level
Transaction level, frequency of transaction log dumps
Disk I/O
Disk I/O and virtual server host
Transaction level, frequency of transaction log dumps
Transaction level
Transaction level
Loss in case of failure
Database modifications done after the last transaction dump
No loss
No loss
Database modifications done after the last transaction dump
Unfinished transactions
Unfinished transactions
Configuration requirements
Disk space and separate backup media (e.g. a tape)
Separate disk drives
Identical Database Server hardware, shared disk array system, cluster software
Disk space and separate backup media (e.g. a tape). Identical Database Server hardware, a connection between the servers.
Identical Data base Server hardware, a connection between Database Servers and Replication Server
Identical Database Server hardware, a connection between Database Servers and Replication Server
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 24
76.8060-70222D © 2014 Coriant.
4 Database Protection Levels
2
Scheduled Database Dumps
Mirrored Disk Drives
Clustering
Cold Standby
Warm Standby
Hot Standby
Additional requirements
Dumps must be tested regularly
None
Ordered from Oracle. A prerequisite from Oracle: two trained cluster administrators.
Dumps must be tested regularly in the cold backup
Two trained Replication Server administrators. Automatic monitoring for system.
Two trained Replication Server administrators. Automatic monitoring for system.
Supported database platforms
Windows, Solaris2, Linux
Windows, Solaris2, Linux
Solaris2
Windows, Solaris2, Linux
Linux
Linux
May require starting other 8000 INM servers
Yes
No
Yes
Yes
Yes
No
Solaris is supported only for the currently installed base and should not be used in new deployments.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 25
5 Computer Requirements for 8000 Intelligent Network Manager
5
5.1
Computer Requirements for 8000 Intelligent Network Manager RAM, CPU and Disk Requirements The recommendations in this chapter are general guidelines and minimum requirements. Additional memory and/or faster processor may provide better performance. When purchasing new servers for 8000 Intelligent Network Manager, it is recommended to use a 64-bit operating system with a minimum of 8 GB of RAM. Moreover, when upgrading existing servers to a 64-bit operating system it is recommended to install a minimum of 8 GB of RAM. When upgrading to SR6.0 it is possible to continue using servers running a Windows 32-bit operating system if the memory requirement for those servers is less than or equal to 4 GB of RAM. Refer to the RAM and CPU requirement table below for more details. The RAM and CPU requirements depend on the actual network size. To make reading easier, the network size is defined as follows. Network Size Definition Small
1 - 2 Communication Servers
Medium
3 – 6 Communication Servers
Large > 6 Communication Servers
The number of Communication Serve rs is calculated as described in 2.3 Communication Server .
If performance history data collection is going to be used, contact your Coriant representative for more detailed informat ion about the Database Server requirements.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 26
76.8060-70222D © 2014 Coriant.
5 Computer Requirements for 8000 Intelligent Network Manager
5.1.1
5.1.2
5.1.3
Single Server Configuration Hardware
Minimum CPU
Minimum RAM
SSC
1 x Intel Xeon 6-core 1.9 GHz (64-bit) or better
8 GB
Hardware
Minimum CPU
Minimum RAM
DSC - Server 1 (Database Server, Management Server)
1 x Intel Xeon 6-core 1.9 GHz (64-bit) or better
8 GB
DSC - Server 2 (Communication Server)
1 x Intel Xeon quad-core 2.2 GHz or better (100 nodes)
4 GB
Dual Server Configuration
Multi-server Configuration Minimum CPU3 Hardware
3To
Minimum RAM (based on the network size) Small
Medium
Large
Workstation
1 x Intel Core 2 Duo 2 GHz or better
2 GB
4 GB
4 GB
Database Server (x64)
1 x Intel Xeon quad-core 2.2 GHz or better (3000 nodes)
8 GB
16 GB
32 GB
match the physical CPUs to virtual CPUs in the virtualized server environment, contact your virtual server environment supplier.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 27
5 Computer Requirements for 8000 Intelligent Network Manager
Minimum CPU3 Hardware
4
Minimum RAM (based on the network size) Small
Medium
Large
Database Server (sparc)4
1 x Oracle SPARC VII quad-core or better (1 GB
Recovery Server
1 x Intel Core 2 Duo 2 GHz or better
1 GB
1 GB
>1 GB
ThinClient Server
2 x Intel Xeon quad-core 2.2 GHz or better
2 GB Base + 2 GB per supported 8000 INM workstations + 256 MB per supported 8100 workstations
2 GB Base + 3 GB per supported 8000 INM workstations + 512 MB per supported 8100 workstations
2 GB Base + 3 GB per supported 8000 INM workstations + 1 GB per supported 8100 workstations
Only supported for the currently installed base and should not be used in new deployments.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 28
76.8060-70222D © 2014 Coriant.
5 Computer Requirements for 8000 Intelligent Network Manager
5.1.4
Network Manager Resilience Service Hardware Requirements Minimum CPU Hardware
Minimum RAM (based on the network size) Small
Medium
Large
Replication Server
1 x Intel Xeon 6-core 1.9 GHz (64-bit) or better
8 GB
16 GB
32 GB
OpenSwitch Server
1 x Intel Xeon 6-core 1.9 GHz (64-bit) or better
8 GB
16 GB
32 GB
For the latest information on the operating system and Sybase versions, contact your Coriant representative.
5.1.5
Disk Requirements for Workstations The recommendations in this chapter regarding disks apply to 8000 Intelligent Network Manager workstations. These recommendations are general guidelines and minimum requirements. Additional disk size or protection mechanisms can be used. The recommended minimum size of the physical disks is 100 GB. 8000 Intelligent Network Manager Workstations in Windows 8000 INM workstations
5.1.6
Disk 1 – OS + 8000 INM software
Disk Requirements for Servers The recommendations in this chapter regarding disks apply to 8000 Intelligent Network Manager servers and Database Servers. These recommendations are general guidelines and minimum requirements. Additional disk size or protection mechanisms can be used. The disks can be categorized into two categories. • Internal (I) – Disks that reside physically internal to the server hardware. • External (E) – Disks that reside external to the server hardware on a storage device e.g. Fibre Channel Disk Array or Storage Area Network (SAN). The disks represented in the below tables are virtual disks, not physical disks. The actual number of physical disks underneath a virtual disk depends on the implemented protection mechanism and the vendor. The operating system (OS) disk is recommended to be protected by RAID 1, i.e. mirroring, whereas the database disks are recommended to be protected by RAID 1+0. The recommended minimum sizes of the physical disks are 146 GB for internal and 300 GB for external disks.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 29
5 Computer Requirements for 8000 Intelligent Network Manager
8000 Intelligent Network Manager Servers Windows/Linux5 (1 disk) Disk 1(I/E)
RAID 1
Operating System and 8000 INM software
Single Server/Dual Server Con figuration Windows/Linux5 (4 disks) Disk 1 (I/E)
RAID 1
Operating System, Sybase ASE, 8000 INM software, Master, tempdb and systemprocs.
Disk 2 (I/E)
RAID 1
Data Volume
Disk 3 (I/E)
RAID 1
Log Volume
Disk 4 (I/E)
RAID 1
Backup
Disk 1 (I/E)
RAID 1
Operating System and Sybase ASE software
Disk 2 (I/E)
RAID 10 (or 1)
Master, tempdb, systemprocs and Data Volume
Disk 3 (I/E)
RAID 10 (or 1)
Log Volume
Disk 4 (I/E)
RAID 5 (or 1, 6 or 10)
Backup
Disk 5 (I/E)
RAID 10 (or 1)
Separate PM Data (optional)
Disk 6 (I/E)
RAID 10 (or 1)
Separate PM Log (optional)
Disk 1 (I)
RAID 1
Operating System and Sybase ASE software
Disk 2 (E)
RAID 10 (or 1)
Master, tempdb, systemprocs, Data Volume
Disk 3 (E)
RAID 10 (or 1)
Log Volume
Disk 4 (E)
RAID 5 (or 1, 6 or 10)
Backup
Disk 1 (I)
RAID 1
Operating System and Sybase REP software
Disk 2 (I)
RAID 1
Replication Volume
Sybase Database Servers Windows/Linux (5 or 6 disks)
Solaris 2(4 disks)
Sybase Replication Server Linux (4 disks)
5
Linux currently supports the 5500, 7090 and 7100 network elements.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 30
76.8060-70222D © 2014 Coriant.
5 Computer Requirements for 8000 Intelligent Network Manager
Sybase OpenSwitch Server Linux (2 disks) Disk 1 (I)
RAID 1
Operating System and Sybase OSW software
The recommended con figuration for the 8000 Intelligent Network Manager Database Server disk system (without the optional separate PM database) is presented below.
Fig. 6 Recommended Database Server Disk System
The disks can reside as internal disks inside the Database Server, or in an external disk system.
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 31
5 Computer Requirements for 8000 Intelligent Network Manager
Database Server Disk System Capacities by Network Size IO Requirement for Data and Log
RAID Group Capacity
MB/s
IOPS6
master, procs, db8000 data, tempdb data
db8000 log, tempdb log
Backup
Small network
10 MB/s
135 IOPS
50 GB
100 GB
200 GB
Medium network
50 MB/s
670 IOPS
250 GB
500 GB
2.5 TB
Large network
200 MB/s
2600 IOPS
500 GB
1000 GB
5 TB
Network Share Server for ThinClient User Data 50 MB
Minimum required disk space per user
5.1.7
Accessories Needed for Servers The following accessories are related to the 8000 Intelligent Network Manager servers and Database Servers. The speci fications may vary according to the vendor.
Accessories for Database Servers External Disk Array Hardware
Model compatibility
Supporting Dual Fibre Channel (FC) RAID and large disks
Disk system software
Vendor specific Disk system software e.g. Veritas Volume Manager, zfs, Solaris Volume Manager, Red Hat Native Driver, EMC storage management software
Backup Tape Device Hardware
Drive
LTO drive
6
IOPS measured from the disk HW level and recorded in 8000 Intelligent Network Manager testing. Based on the results, IOPS measured from the OS level is 1.5 times IOPS from the disk HW level.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 32
76.8060-70222D © 2014 Coriant.
5 Computer Requirements for 8000 Intelligent Network Manager
Other components Drives
DVD-ROM drive
LAN adapter
With four on-board RJ45 10/100/1000Base-T (Copper) Gigabit Fast Ethernet ports
Display
VT 100 or compatible terminal, terminal concentrator or graphic terminal supported by vendor
Accessories for 8000 Intelligent Network Manager Servers Accessories Set – X.25 Adapter DXX Server on Windows Eiconcard for X.25
Eiconcard S94 (310-208) Eiconcard S94/66 (310-828) Eiconcard S94 V2 (306-296) Revision 50 Eiconcard S94 PCI Express (306-298)
Eiconcard connection support
Windows V6R8 for XP, Windows 7 and Server 2008 (32-bit version) Windows V6R8 for XP, Windows 7, Server 2008 and Server 2008 R2 (64-bit version) Windows V6R10 for 64-bit Win 7, Win 8, Server 2003, 2008 R2 and 2012 (included in the 8000 Intelligent Network Manager installation DVD)
USB to Serial Adapter USB to serial adapter
5.2
Targus - connectivity series, USB to Serial (RS232) Adapter
Minimum Requirements for Service Computers The network manager Service Computer software will run on laptop computers which meet the specifications below. Note that Coriant can properly support only 3rd party hardware and software tested by Coriant. In case of problems with other computer types, the vendor of that equipment should be contacted. The requirements for Service Computer laptops are listed in the following. • a laptop computer certified for Microsoft Windows 7 or Windows 8.1 (follow the minimum requirements specified by the operating system vendor) • manufacturer provided hardware drivers • serial port available • parallel or USB port available Minimum performance requirements are listed in the following. • Intel Pentium II processor with 300 MHz clock frequency or better • 512 MB or more RAM (1 GB if Craft Terminal is used in the same computer as manager Service Computer)
76.8060-70222D © 2014 Coriant.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 33
5 Computer Requirements for 8000 Intelligent Network Manager
• 2 MB or more memory in display adapter • 4 GB hard disk or larger with 650 MB free space after installation of Service Computer software
5.3
Minimum Requirements for Workstations The 8000 Intelligent Network Manager workstation software will run on desktop computers which meet the speci fications listed below. The general requirements for workstations are listed in the following. • a computer certified for Microsoft Windows 7 or Windows 8.1 (follow the minimum requirements specified by the operating system vendor) • manufacturer provided hardware drivers Minimum performance requirements are listed in the following. • the amount of RAM is dependent on the size of network. (The minimum amount of required RAM should be checked from the table in chapter 5.1 RAM, CPU and Disk Requirements .) • a display adapter capable of at least 1280 x 1024 resolution with 16-bit color depth is recommended • an Ethernet adapter with a capacity of at least 100 Mbps
Keep in mind that the processor clock speed and th e amount of RAM affects the performance of the computer. For better performance, select your workstations among the latest computer models. Using slow management worksta tions may affect the performance of other workstations as well.
When buying new workstations for 8000 INM, it is recommended to use a at least 2 GB of RAM.
5.4
Software Sets 8000 Intelligent Network Manager supports the Windows 7, Windows 8.1, Windows Server 2008 and Windows Server 2012 operating systems. Linux Management Server and Communication Server are supported for the 5500, 7090, 7100 and mTera UTP networks. Windows, Linux and Solaris are supported for the Database Server.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 34
76.8060-70222D © 2014 Coriant.
5 Computer Requirements for 8000 Intelligent Network Manager
5.4.1
5.4.2
Workstation Software Operating system with 8000 INM
Windows 7 Professional/Enterprise, English with the latest Microsoft recommended patches (64–bit version) Or Windows 8.1 Pro/Enterprise, English with the latest Microsoft recommended patches (64–bit version)
Software for reading help fi les in 8000 INM
Current version of Adobe Acrobat Reader
Server Software – Management Server and Communication Server Operating system with 8000 INM
Windows Server 2008 R2 Standard Edition or better, English (Service Pack 1 or higher) with the latest Microsoft recommended patches (64-bit version) Or Windows Server 2012 R2 Standard Edition or better, English with the latest Microsoft recommended patches (64-bit version) Or Red Hat Enterprise Linux 6 (6.3 or higher) with the latest recommended patches (64-bit version)
Communication Server with 6300 Adapter
MARBEN TM OSIAM OSITP4, version 1.2
6300 Adapter is only supported in Windows Server 2008.
5.4.3
Database Server Software
Sybase
76.8060-70222D © 2014 Coriant.
Windows operating system
Windows Server 2008 R2 Standard Edition or better, English (Service Pack 1 or higher) with the latest Microsoft recommended patches (64-bit version) Or Windows Server 2012 R2 Standard Edition or better, English with the latest Microsoft recommended patches (64-bit version)
Windows Database Server software
Sybase ASE Enterprise Edition 15.5 for Windows x64 64-bit – ESD#5.2 (EBF20630) or the latest Sybase recommended patches Or Sybase ASE Enterprise Edition 15.7 for Windows x64 64-bit – SP122
Unix operating system
Solaris 10 9/10 or higher with the latest Oracle recommended patches (64-bit version)
Unix Database Server software
Sybase ASE Enterprise Edition 15.5 for Oracle Solaris SPARC 64-bit – ESD#5.2 (EBF20632) or the latest Sybase recommended patches Or Sybase ASE Enterprise Edition 15.7 for Oracle Solaris SPARC 64-bit – SP122
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 35
5 Computer Requirements for 8000 Intelligent Network Manager
Linux operating system
Red Hat Enterprise Linux 6 (6.3 or higher) with the latest recommended patches (64-bit version)
Linux Database Server software
Sybase ASE Enterprise Edition 15.7 for Linux x86-64 64-bit – SP122
With new 8000 INM installations, it is recommended to use the Enterprise Edition of Sybase Adaptive Server Enterprise.
5.4.4
5.4.5
5.4.6
5.4.7
ThinClient Server Software Windows operating system
Windows Server 2012 R2 Standard Edition or better, English (Service Pack 1 or higher) with the latest Microsoft recommended patches (64-bit version)
Application Server
Citrix XenApp 7.5 (Windows Server 2012 R2, 64-bit version) Citrix recommended Hotfix Rollup Packs and hotfixes
OpenSwitch Server Software Operating system
Red Hat Enterprise Linux 6 (6.3 or higher) with the latest recommended patches
OpenSwitch Server Software
Sybase OpenSwitch 15.1 for Linux x86 – ESD#7 (EBF20877) or the latest Sybase recommended patches
Replication Server Software Operating system
Red Hat Enterprise Linux 6 (6.3 or higher) with the latest recommended patches
Replication Server Software
Sybase Replication Server 15.7.1 for Linux x86-64 64-bit – SP121 (EBF22360) or the latest Sybase recommended patches
VMware VMware version
5.5
5.0 or higher, supported by the used Windows operating system
Displays Specification
display with 1280 x 1024 resolution or better
Recommendation
19" or larger screen
Small fonts should be used in Windows.
8000 Intelligent Network Manager SR6.0 Third Party Hardware and Software Requirements 36
76.8060-70222D © 2014 Coriant.
