6-Speed Automatic Gearbox 09G

Service

Golf Variant 2007 ➤ Golf Variant 2010 ➤ Jetta 2005 ➤ Jetta 2011 ➤

rrectness of i t to the co nform spec at i h re o n wit in t his

Workshop Manual

6-speed automatic gearbox 09G Edition 04.2010

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Service Department. Technical Information

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

Service

un le

37 - Controls, housing 38 - Gears, control

r fo ng

39 - Final drive - differential

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

32 - Torque converter

ht rig py Co t.

00 - Technical data

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

Repair Group

ility ab y li an pt ce

List of Workshop Manual Repair GroupsList of Workshop Manual Repair GroupsList of Workshop Manual Repair Groups

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

Technical information should always be available to the foremen and mechanics, because their careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a matter of course, be observed. All rights reserved. No reproduction without prior agreement from publisher. Copyright © 2010 Volkswagen AG, Wolfsburg

MEX5R005320

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

Contents 00 - Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Suggestions and criticism, general repair notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Suggestions and criticism of this workshop manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General repair notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic gearbox control unit J217 with fuzzy logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control units in vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Information on “09G gearbox” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Volkswag Tools . . . . . . . . . . . . . . . . . . . . . . . . .k.sw. a.g.en. A. G . . . . . . . .e.n.A.G.d.oe. s. . . . . . . . . . . . . . . . . . . . . no l o Gearbox . . . . . . . . . . . . . . . . . . d. b.y.V. . . . . . . . . . . . . . . . . . . . . . . . t.g.ua.r . . . . . . . . . . . . . . . . a e Gaskets, seals and oil . . . . th. o.ris. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . n. te.e.o . . . . . . . . . . . . u Nuts and bolts . . . . . . . .ss.a. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . r.ac. . . . . . . . . . . Electrical components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Guided fault finding, vehicle self-diagnosis and testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gearbox identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gearbox codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Planetary gearbox and final drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Codes, gearbox allocation, ratios ▸ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 1 2 2 2 2 2 2 2 2 3 4 4 4 5 6 6 7 7 8

32 - Torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

un le

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

1 1.1 1.2 1.3 1.4

ility ab y li an pt ce

1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 1.14 2 2.1 3 3.1 4

1

Torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification of torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing torque converter oil seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 9 9 9 10

37 - Controls, housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 r fo ng

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

5.3

Connecting “tester” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting vehicle diagnosis, testing and information system VAS 5051 . . . . . . . . . . . . Electrical and electronic components and their locations . . . . . . . . . . . . . . . . . . . . . . . . . . Multifunction switch F125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing multifunction switch F125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing multifunction switch F125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting multifunction switch F125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selector mechanism up to 02.2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview of selector mechanism up to 02.2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing selector mechanism with selector lever up to 02.2009 . . . . . . . . Removing and installing selector lever cable up to 02.2009 . . . . . . . . . . . . . . . . . . . . . . . . Checking selector lever cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting selector lever cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency release of selector lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking selector mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Selector mechanism from 03.2009 onwards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview of selector mechanism in vehicles from 03.2009 onwards . . . . . . . . . . . . . . . . . . Removing and installing selector lever and selector mechanism with selector lever cable from 03.2009 onwards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency release of selector lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ht rig py Co t.

1 1.1 2 3 3.1 3.2 3.3 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 5 5.1 5.2

Contents

11 11 13 18 18 19 20 22 22 23 23 30 30 31 32 33 35 35 36 37

i

lks,wJetta agen A2011 Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta AG. Vo➤ n2005 G do ➤ es n wage s k l ot g o 6-speed automatic gearbox 09G - Editiony V04.2010

.. Removing gearbox, vehicles with 1.6 l - 75 kW and 2.0 l - 110 kW (FSI) engines . . . . . . . . Installing gearbox, vehicles with 1.6 l - 75 kW and 2.0 l - 110 kW (FSI) engines . . . . . . . . Removing gearbox, vehicles with 2.5 l, 110 kW engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing gearbox, vehicles with 2.5 l, 110 kW engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . Torque settings, gearbox to engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing gearbox, Jetta 2011 ▸ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing gearbox, Jetta 2011 with 2.0 l - 85 kW engine . . . . . . . . . . . . . . . . . . . . . . . . . . Installing gearbox, Jetta 2011 with 2.0 l - 85 kW engine . . . . . . . . . . . . . . . . . . . . . . . . . . Removing gearbox, Jetta 2011 with 2.5 l - 125 kW engine . . . . . . . . . . . . . . . . . . . . . . . . Installing gearbox, Jetta 2011 with 2.5 l - 125 kW engine . . . . . . . . . . . . . . . . . . . . . . . . . . Torque settings, gearbox to engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transporting gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATF cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly overview - ATF cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking ATF level and topping up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking ATF level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Topping up ATF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draining and filling ATF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . do c um en

r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

un le

ility ab y li an pt ce

c o p yri gh t . C op yi

6.1 6.2 6.3 6.4 6.5 7 7.1 7.2 7.3 7.4 7.5 8 9 9.1 10 10.1 10.2 10.3

ht rig py Co t.

6

ua b ran ed tee ris o h t or u Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ac ▸, Jetta a s s Wagon 2008 ▸ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38 38 45 45 53 54 57 57 63 63 72 72 75 76 76 77 78 79 80

38 - Gears, control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 agen lksw Vo by

Renewing oil seal for selector shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATF pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing ATF pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATF strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing ATF strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Valve body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing valve body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing wiring harness with 14-pin connector (for solenoid valves) . . . . . . Removing and installing wiring harness with 8-pin connector (for sender) . . . . . . . . . . . . Removing and installing gearbox input speed sender G182 . . . . . . . . . . . . . . . . . . . . . . . . Removing and installing gearbox output speed sender G195 . . . . . . . . . . . . . . . . . . . . . . AG.

Prote cted by

1 2 2.1 3 3.1 4 4.1 4.2 4.3 4.4 4.5 4.6

81 82 82 85 85 86 87 91 103 105 106 107

39 - Final drive - differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 1 1.1

ii

Contents

Renewing oil seals for flange shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Renewing oil seal for flange shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

00 –

Technical data

1

Suggestions and criticism, general repair notes Suggestions and criticism of this work‐ shop manual

thi sd o cu m en

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

rrectness of i t to the co nf o r m spec atio h re n in wit

– You can do this by clicking the ⇒ Feedback button at the top in the menu bar.

ility ab y li an pt ce

This workshop manual was made for you. It should support you and be an aid to you. If you use ⇒ ELSA, you can send us sug‐ gestions, “praise and criticism” from anywhere in the world.

ht rig py Co t.

1.1

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

You will not always receive a reply from Volkswagen but your message will always be read. We make great effort to implement your suggestions for the workshop manuals.

1. Suggestions and criticism, general repair notes

1

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

1.2

General repair notes

To ensure flawless and successful gearbox repairs, the greatest care and cleanliness as well as the use of good and proper tools are essential. Obviously, the basic rules for safety also apply dur‐ ing repair work. A number of generally valid instructions applicable for the various repair procedures - which were formerly repeated a number of times at numerous places in the workshop manual - are summar‐ ised here. They apply to this workshop manual.

1.3

Gearbox

The “6-speed automatic gearbox 09G” has six hydraulically ac‐ tuated forward gears. When the torque converter lock-up clutch closes, 2nd, 3rd, 4th, 5th and 6th gears become mechanically driven gears by eliminating torque converter slip.

1.4

Torque converter

The torque converter is equipped with a lock-up clutch. The lockup clutch locks up depending on load and speed. The 2nd, 3rd, 4th, 5th and 6th gears can be driven mechanically (without slip).

1.5

ATF

The ATF is filled for life. The ATF need not be changed during a service. . Volkswagen AG gen AG d

a oes ksw n Use only ATF which has been Elec‐ Vol ordered as a part from theot⇒ gu y b ara tronic parts catalogueed“ETKA” . n is or

tee or ac

un le

pe rm itte d

Automatic gearbox control unit -J217with ⇒ fuzzy logic

The gear change point, which is dependent on the driving situa‐ tion and driving resistance, is determined automatically. Advantages: • • • •

Gear changes will be fuel-consumption orientated. Maximum engine output is always available. Individual adaptation of gear change points in all driving sit‐ uations. Gear change points are infinitely variable.

1.7

Control units in vehicle

r te o iva r rp fo g n

Information on “09G gearbox” agen lksw Vo by

c o p yri gh t. C op yi

Design and function of gearbox

ht rig py Co t.

1.8

♦ ⇒ Multimedia training; Automatic gearbox 09G AG.

Prote cted by

♦ ⇒ Self-study programme No. 291 ; Automatic gearbox 09G

1.9

Tools

A summary of the special tools and workshop equipment used in the workshop manual precedes each repair procedure and can be found in “Special tools/Workshop equipment” binder.

2

Rep. Gr.00 - Technical data

do c um en

The installation locations of all vehicle control units and other useful information can also be found in ⇒ Current flow diagrams, Electrical fault finding and Fitting locations.

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

1.6

ility ab y li an pt ce

th The ATF levels in au the planetary gearbox and final drive are s s checked and topped up together.

. Volkswage

n AG d AG Golf Variant 2007 age,nGolf Variant 2010 o➤ es n, Jetta 2005 ➤ , Jetta 2011 ➤ w➤ ot g olks V y 6-speed automatic gearbox 09G - Edition 04.2010 ua b d r

an tee or ac

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

e ris ho t The catalogue is also available on au ⇒ CD-ROM and can be ordered ss the usual way from Bertelsmann.

Uncertainty often occurs with smaller bolts having low tightening forces. Torque wrench 2...10 Nm -V.A.G 1783- can be used with these bolts.

rrectness of i t to the co nform spec at i h re o n wit in t his

1.10

Gearbox

♦ If gearbox covers have been unbolted or gearbox has no fluid, do not run engine or tow vehicle.

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

♦ Place removed parts on a clean surface. Cover parts to pre‐ vent soiling. Use plastic sheeting and paper. Use lint-free cloths only!

ht rig py Co t.

♦ When installing the gearbox, ensure that dowel sleeves be‐ tween the engine and gearbox are correctly located.

do c um en

♦ First thoroughly clean connecting points and surrounding areas and then loosen bolts.

AG.

♦ Install only clean parts; do not remove new parts from pack‐ aging until immediately before installing. ♦ If repair work cannot be performed immediately, carefully cov‐ er or seal components. ♦ With gearbox removed, secure torque converter against falling out. Gearboxes with and without filler pipe Here is an “example” with a filler pipe as it is installed in “older” gearboxes. This pipe has been discontinued.

This “old” filler opening with the red cap is not needed because ATF can be drained or filled as required through the bottom hole. The “height” of this tube determines the level of the ATF. The tube must be removed to drain the fluid. ♦ After installation, check the ATF level and top up ⇒ page 77 . ♦ Capacities ⇒ page 7 .

1. Suggestions and criticism, general repair notes

3

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

1.11

Gaskets, seals and oil

♦ Always renew O-rings, seals and gaskets. ♦ Before installing a radial oil seal, coat sealing lips and area between them with sealing grease -G 052 128- . ♦ Open side of oil seal faces oil. ♦ After installing, check ATF level.

un le

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o gu yV Caution b ara d e nte is r o e th uwhen ra Be careful working with oil. Dispose of drained oil oac‐ a c s s regulations. Remember: one drop of oil will contam‐ cording to

1.12

Nuts and bolts

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

inate 1,000 litres of water.

♦ Loosen and tighten securing bolts and securing nut for covers and housings diagonally. ♦ Torque settings are specified for unoiled bolts and nuts.

♦ Threads of bolts secured with locking fluid must be cleaned with a wire brush. Then insert bolts with locking fluid AMV 185 100 A1. ♦ Use a thread chaser to clear residual locking fluid from all threaded holes into which self-locking bolts are to be screwed. Otherwise there is a danger of bolts shearing when subse‐ quently being removed.

1.13

r fo ng

♦ Always renew self-locking bolts and nuts.

Electrical components

You have probably at some time received an electrical shock when touching a metal object. This is due to the electrostatic charge of the human body. This charge can disturb the function of electrical components of the gearbox and of the selector mech‐ anism. ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

– Before beginning work on electrical components, touch an earthed object, for example a water pipe or lifting platform. Do not touch connectors or “open” electronic components directly.

4

Rep. Gr.00 - Technical data

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

1.14

Guided fault finding, vehicle self-diag‐ nosis and testing

Before making repairs to the automatic gearbox, determine the cause of the fault as precisely as possible with the aid of “guided fault finding”. Guided fault finding is carried out using the vehicle diagno‐ sis, testing and information system -VAS 5051B- ⇒ page 11 .

The guided functions will guide you to the ATF temperature in the shortest way possible ⇒ page 11 .

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

thi sd o cu m en

ht rig py Co t.

agen lksw Vo by

AG.

1. Suggestions and criticism, general repair notes

5

Prote cted by

c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

2

Gearbox identification

“6-speed automatic gearbox 09G” is fitted in Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸ and Jetta 2011. The allocation of the gearbox to the vehicles can be found here:

Gearbox codes

02 I Year -2002of manufacture

The gearbox code also appears on the vehicle identification plates.

6

Rep. Gr.00 - Technical data

Prote cted by

05 I Month

AG.

08 I Day

agen lksw Vo by

Example:

rrectness of i t to the co nform spec at i h re o n wit in t his

“6-speed automatic gearbox 09G” -arrow 2-

do c um en

Code letters -arrow 1-

GGZ I Identification code

ility ab y li an pt ce

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

Code letters -arrow-

c o p yri gh t . C op yi

2.1

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

ht rig py Co t.

Codes, gearbox allocation, ratios ⇒ page 8 .

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

3

Capacities

3.1

Planetary gearbox and final drive Capacities

“6-speed automatic gearbox 09G”

Initial filling Change

approx. 7.0 l Filled for life no change ATF is available as a part. Therefore, the part number for it can be found in the ⇒ Electronic parts catalogue “ETKA”.

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

do c um en

ht rig py Co t.

r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

Lubricant

3. Capacities

7

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

4

Codes, gearbox allocation, ratios ▸

If Genuine parts are required for a repair, always refer to the gearbox code. “Automatic gearbox 09G” “MAM”

“HFT”, “HTP”, “HDN”, “HFU”, “JUH” “HRM”, “JUJ” k s l w o a V g . e G n A A 2.0 l - 85 kW 2.0 l 110 kW 2.5 G dlo - 110 kW agen es n ksw l ot g (FSI) o yV

ua ran tee

b ed ris o h t au ss

r fo ng

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Rep. Gr.00 - Technical data

2.5 l - 125 kW or ac

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

8

“KGL”

ility ab y li an pt ce

un le

“HFS”, “HTN”, “JTY” 1.6 l - 75 kW

ht rig py Co t.

Identification code Engine

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

32 –

Torque converter

1

Torque converter

1.1

Identification of torque converter

There are various torque converters. They are identified by codes. Torque converter/gearbox allocation ⇒ Replacement parts cata‐ logue ⇒ ETKA

1.2

Draining torque converter

Special tools and workshop equipment required AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

♦ -V.A.G 1358 A/1- Oil extraction probe – Extract ATF from torque converter using -V.A.G 1358 A- and probe -V.A.G 1358 A/1- .

1.3

Removing and installing torque convert‐ er oil seal

Special tools and workshop equipment required

ht rig py Co t.

r fo ng

♦ Thrust piece -T10175-

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

♦ -V.A.G 1358 A- Oil extraction unit

1. Torque converter

9

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

♦ Oil seal extractor lever -VW 681-

Removing

AG.

Prote cted by

1.4

agen lksw Vo by

c o p yri gh t . C op yi

– Drive in seal flush thrust piece -T10175- .

ht rig py Co t.

Installing

Installing torque converter

– Carefully push on torque converter hub via oil seal to first stop. – Turn torque converter towards gearbox using light pressure until notch in hub -arrow- engages in follower of pump gear and torque converter can be felt to slip in place. The torque converter is properly inserted when it can easily be turned by hand and is seated equally deep in gearbox around the entire circumference. Caution

If engine and gearbox are brought together with force because the torque converter is improperly fitted, both gearbox and tor‐ que converter will be damaged.

10

Rep. Gr.32 - Torque converter

do c um en

r te o iva r rp fo g n

– Pry out seal with lever -VW 681- .

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 . Volkswage

Controls, housing

1

Connecting “tester” pe rm itte d

un le

37 –

n AG d oes not gu ara nte eo ra c

♦ Vehicle diagnosis, testing and information system -VAS 5051-

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

Volkswagen offers various devices such as

ility ab y li an pt ce

AG agen ksw l o yV db ise r tho au s s

♦ Vehicle diagnosis, testing and information system -VAS 5051B♦ Tester -VAS 5051/11A♦ Vehicle diagnosis and service information system -VAS 5052♦ Diagnostic system -VAS 5053The operation of these “devices” is described in the respective user's manuals. The following description refers to the vehicle diagnosis, testing and information system -VAS 5051- ⇒ page 11 .

Special tools and workshop equipment required c o p yri gh t. C op yi

♦ Vehicle diagnosis, testing and information system -VAS 5051-

ht rig py Co t.

r te o iva r rp fo g n

Connecting vehicle diagnosis, testing and information system -VAS 5051-

do c um en

1.1

agen lksw Vo by

AG.

Prote cted by

WARNING

♦ During a road test, always secure testing and measuring equipment on the back seat. ♦ These devices may be operated only by a passenger dur‐ ing a test drive. – Push connector of diagnosis cable -VAS 5051/1- -2- or VAS 5051/3- onto diagnosis connection.

1. Connecting “tester”

11

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Switch on “tester” -arrow-. The “tester” is ready for use when it is possible to choose between the buttons Guided functions and Guided fault finding on the “right” of the screen. Depending on equipment and version of the tester, other func‐ tions may be “displayed” such as: ♦ ElsaWin ♦ Testing ♦ Self-diagnosis The “tester” is now ready for use. – Switch on ignition.

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

r fo ng

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

Rep. Gr.37 - Controls, housing

ht rig py Co t.

12

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

– Touch a button on the screen to start the desired function.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

2

Electrical and electronic components and their locations

1 - Control unit for automatic gearbox -J217❑ The control unit trans‐ mits and receives data from the ⇒ data bus. ❑ Installation location in Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸ ⇒ page 14 ❑ Installation location in Jetta 2011 ▸ with 2.0 l 85 kW engine ⇒ page 15 . ❑ Installation location in Jetta 2011 ▸ with 2.5 l 125 kW engine ⇒ page 15 . ❑ Can be checked using “guided fault finding” of VAS 50512 - Engine control unit ❑ The control unit trans‐ mits and receives data from the data bus ❑ Location and removing and installing ⇒ Rep. Gr. 23 for the respective AG. Volkswagen AG d agen oes engine code letter ⇒ ksw not l o gu Rep. Gr. 24 for the re‐ ed by V ara nte s i r spective engine code o eo th ra letter au c ss

4 - Valve body ❑ Location ⇒ page 15 ❑ Components can be checked using “guided fault finding” of -VAS 5051❑ Allocation ⇒ Electronic parts catalogue “ETKA”

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

7 - Wiring harness, 14-pin ❑ For solenoid valves

ht rig py Co t.

6 - Gearbox oil temperature sender -G93❑ Location ⇒ page 16 ❑ Can be checked using “guided fault finding” of -VAS 5051-

thi sd o cu m en

5 - Wiring harness, 8-pin ❑ For senders ❑ With gearbox oil temperature sender -G93❑ Location ⇒ page 16 ❑ Removing and installing ⇒ page 105 ❑ Allocation ⇒ Electronic parts catalogue “ETKA”

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

3 - Multifunction switch -F125❑ Location ⇒ page 15 ❑ Can be checked using “guided fault finding” of VAS 5051❑ Removing, installing and adjusting ⇒ page 18 .

2. Electrical and electronic components and their locations

13

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ❑ Location ⇒ page 16 ❑ Removing and installing ⇒ page 103 ❑ Allocation ⇒ Electronic parts catalogue “ETKA” 8 - Hydraulic pressure sender 1 for automatic gearbox -G193❑ Not installed in all gearboxes ❑ Allocation ⇒ Electronic parts catalogue “ETKA” ❑ Location ⇒ page 16 9 - Hydraulic pressure sender 2 for automatic gearbox -G194❑ Not installed in all gearboxes ❑ Allocation ⇒ Electronic parts catalogue “ETKA” ❑ Location ⇒ page 16 10 - Gearbox input speed sender -G182❑ Location ⇒ page 17 ❑ Removing and installing ⇒ page 106 ❑ Can be checked using “guided fault finding” of -VAS 505111 - Gearbox output speed sender -G195❑ Location ⇒ page 17 ❑ Removing and installing ⇒ page 107 ❑ Can be checked using “guided fault finding” of -VAS 505112 - Selector lever lock solenoid -N110❑ Location: selector lever lock solenoid is located in the selector mechanism. ❑ Can be checked using “guided fault finding” of -VAS 5051-

. Volkswagen AG gen AG does not gu ara nte eo ra c

wa 13 - Tiptronic switch -F189olks yV b ed ❑ Location ⇒ page 17 ris ho t u ❑ Can be checked using “guided fault afinding” of -VAS 5051-

ss

un le

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

15 - Diagnostic connection ❑ Location ⇒ page 17

ility ab y li an pt ce

14 - Terminal 50 voltage supply relay -J682❑ In E box in engine compartment ⇒ Current flow diagrams, Electrical fault finding and Fitting locations.

16 - Selector lever position display -Y6❑ Location ⇒ page 17 ❑ Removing and installing ⇒ Electrical system; Rep. Gr. 90 ; Gauges, instruments; Dash panel insert . Automatic gearbox control unit -J217- -arrow- in Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸ Location: control unit is located in front left wheel housing.

AG.

Prote cted by

Rep. Gr.37 - Controls, housing

agen lksw Vo by

c o p yri gh t . C op yi

14

ht rig py Co t.

r fo ng

– Wheel housing liner must be removed for removing and in‐ stalling.

pe rm itte d

ility ab y li an pt ce

un le

Golf Variant 2007

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or ➤ ➤au, Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ac ss 6-speed automatic gearbox 09G - Edition 04.2010

es, in part or in w l purpos hole ercia , is n m ot com

Automatic gearbox control unit -J217- -A- in Jetta 2011 ▸ with 2.0 l - 85 kW engine

rrectness of i t to the co nform spec a t i h re o n in wit thi s

Location: control unit is located in plenum chamber on right. – Plenum chamber cover must be removed for removal and in‐ stallation ⇒ Rep. Gr. 50 ; Plenum chamber cover; Removing and installing plenum chamber cover .

Automatic gearbox control unit -J217- -A- in Jetta 2011 ▸ with 2.5 l - 125 kW engine

ht rig py Co t.

r te o iva r rp fo g n

do c um en

Location: control unit is located in front left of engine compartment next to battery.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Multifunction switch -F125Location: multifunction switch is located on top of the gearbox.

Valve body Location: valve body is bolted to underside of gearbox housing and covered by pan. Solenoid valves -N88- , -N89- , -N90- , -N91- , -N92- , -N93- , N282- and -N283- are attached to valve body.

2. Electrical and electronic components and their locations

15

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Wiring harness, 8-pin ♦ Wiring harness for senders ♦ With integrated gearbox oil temperature sender -G93-arrowLocation: wiring harness is attached to valve body in gearbox.

Wiring harness, 14-pin ♦ Wiring harness for solenoid valves. Location: wiring harness is attached to valve body in gearbox.

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

Hydraulic pressure sender 1 for automatic gearbox -G193- and hydraulic pressure sender 2 for automatic gearbox -G194This sender is not installed in all gearboxes. Location:

Automatic gearbox hydraulic pressure sender 1 -G193- -1- and automatic gearbox hydraulic pressure sender 2 -G194- -2- are bolted into valve body.

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Rep. Gr.37 - Controls, housing

thi sd o cu m en

16

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ . Volkswage G automatic gearbox 09G - Edition 04.2010 gen AG 6-speedn A does swa

Gearbox input speed sender -G195-

gearbox output speed

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

Location: senders are installed in gearbox housing above valve body.

not gu ara nte eo ra c

1 - Gearbox input speed sender -G182-

rrectness of i t to the co nform spec at i h re o n wit in t his

2 - Gearbox output speed sender -G195-

ility ab y li an pt ce

k Vol by d e sender -G182and ris tho u a ss

Location: Tiptronic switch is integrated into selector mechanism. ht rig py Co t.

In vehicles with a multifunction steering wheel, the buttons on the steering wheel and their cable connections must also be checked.

do c um en

Tiptronic switch -F189-

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Diagnostic connection Location: diagnosis connector -arrow- is located on left below driver storage compartment.

Selector lever position display -Y6Location: in dash panel insert

2. Electrical and electronic components and their locations

17

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

3

Multifunction switch -F125-

Removing multifunction switch -F125- ⇒ page 18 Installing multifunction switch -F125- ⇒ page 19 Adjusting multifunction switch -F125- ⇒ page 20

3.1

Removing multifunction switch -F125-

Carry out procedure as follows: – Move selector lever to position “N”. – Switch off ignition.

. Volkswagen AG gen AG does not gu ara nte eo ra c

♦ Do not use any pliers, otherwise securing tabs on cable sup‐

port bracket could break off.

♦ Do not bend or kink selector lever cable.

– Lever cable -1- off lever -3- using an open jaw spanner -2-.

18

Rep. Gr.37 - Controls, housing

AG.

– Remove spring ring -2- and lever -3- from selector shaft -4-.

agen lksw Vo by

Prote cted by c o p yri gh t. C op yi

– Unscrew nut -1-.

ht rig py Co t.

r fo ng

– Pull connector off multifunction switch -F125- .

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

au ss

ility ab y li an pt ce

Note

un le

– In order to remove selector lever cable from gearbox, first re‐Volkswa y lease cable -arrows 1- and then remove it from cable support db se i r bracket -arrow 2-. tho

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Carefully bend back hooks of lock washer -2- using a screw‐ driver. – Renew securing clip if hooks have broken off. – Unscrew nut -1-. – Remove bolts -5-. – Pull multifunction switch -4-, together with washers -2- and -3-, off selector shaft -6-.

3.2

Installing multifunction switch -F125-

Special tools and workshop equipment required

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

rrectness of i t to the co nform spec a t i h re o n in wit thi s

Carry out procedure as follows:

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

♦ Torque wrench -V.A.G 1331-

Install in the reverse order of removal, observing the following: – Place multifunction switch -4- on selector shaft -6-. – Tighten securing bolts -5- for multifunction switch hand-tight. – Bend hooks of lock washer -2- back.

– Put washers -2- and -3- on selector shaft -6-. – Install washer -2- with long, narrow guides in long, narrow re‐ cesses of selector shaft -6-. c o p yri gh t. C op yi

– Secure nut -1- by bending up hooks on lock washer -2-.

agen lksw Vo by

AG.

Prote cted by

– Renew securing clip if hooks have broken off.

ht rig py Co t.

– Tighten nut -1- to 7 Nm.

3. Multifunction switch F125

do c um en

r te o iva r rp fo g n

– Install washer -2- with hooks pointing up.

19

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Push lever -3- onto selector shaft -4-. – Use lever -3- to shift gearbox to “P” position, i.e. press lever -3- back (opposite direction of travel) to stop. – Now use lever -3- to shift gearbox to “N” position. To do this, push lever -3- two detent positions forwards in direction of travel. – Place spring ring -2- and nut -1- on selector shaft -4-. – Tighten nut -1- to 13 Nm. – Check selector mechanism ⇒ page 33 .

3.3

Adjusting multifunction switch -F125-

Special tools and workshop equipment required ♦ Setting gauge -T10173-

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

– Do not kink selector lever cable.

Adjustment prerequisites

•

Selector shaft is set to “N” position.

•

Securing bolts for multifunction switch -F125- have been loos‐ ened.

•

Selector shaft lever has been removed.

Prote cted by

c o p yri gh t . C op yi

Rep. Gr.37 - Controls, housing

do c um en

20

AG.

Selector lever cable is disconnected from selector shaft lever.

agen lksw Vo by

•

ht rig py Co t.

3.3.1

rrectness of i t to the co nform spec at i h re o n wit in t his

– Move selector lever to position “N”.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Carry out procedure as follows: – Place setting gauge on selector shaft -2- and turn multifunction switch -1- until setting gauge engages in lug on multifunction switch connector. – Secure setting gauge on selector shaft -2- with bolt -3-. n AG. Volkswagen A

G do es n ot g ua ran tee or ac

ge swa

k Vol to 6 Nm. – Tighten bolts -arrowsby d se

ri gauge. – Remove setting tho au

r fo ng

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

ht rig py Co t.

un le

ility ab y li an pt ce

– Continuess installation in reverse order of removal ⇒ page 19 .

3. Multifunction switch F125

21

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

un le

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d Golf Variant 2007 ➤ , Golf Variant 2010 nte ise ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ r o eo h t 6-speed automatic gearbox 09G -auEdition 04.2010 ra c s s

Selector mechanism up to 02.2009

Before working on vehicle with engine running, move selector lever into position “P” and apply handbrake. Selector mechanism from 03.2009 onwards ⇒ page 35 .

3 - Bolt with spring ❑ 3 Nm 4 - Pin ❑ Removing ⇒ page 23 ❑ Do not grease 5 - Locking plate ❑ Always renew after re‐ moving 6 - Nut ❑ 9 Nm ❑ Qty. 4 7 - Selector housing ❑ With seal 8 - Selector lever cable ❑ Cable must not be greased ❑ Removing and installing ⇒ page 23 ❑ Checking ⇒ page 30

22

Rep. Gr.37 - Controls, housing

Prote cted by

2 - Selector mechanism with selector lever ❑ Removing and installing ⇒ page 23

AG.

Always pull out button past the felt pressure point before installing knob.

agen lksw Vo by

–

c o p yri gh t. C op yi

1 - Selector cover with knob ❑ Do not remove knob without reason. For emergency release, on‐ ly the cover needs to be unclipped ⇒ page 31 . ❑ Before removing knob, pull button out past its pressure point. Secure button with cable tie or appropriate wire against being pressed in. This will prevent the button from being accidentally pressed into the knob. ❑ If button is pressed into removed handle

r fo ng

Overview of selector mechanism up to 02.2009

ht rig py Co t.

4.1

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

WARNING

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

4

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ❑ Adjusting ⇒ page 30 9 - Hexagon nut with washer ❑ 8 Nm ❑ Qty. 4

4.2

Removing and installing selector mech‐ anism with selector lever up to 02.2009

. Volkswagen AG gen AG does not gu ara nte eo ra c

Carry out procedure as follows:Volkswa

Following installation, selector lever cable must be checked for ease of movement and be adjusted.

rrectness of i t to the co nform spec at i h re o n wit in t his

– Remove selector lever cable from gearbox ⇒ page 23 .

ility ab y li an pt ce

ss

– Remove centre console ⇒ Rep. Gr. 68 ; Compartments, cov‐ ers and trims . – Remove selector lever cable from gearbox ⇒ page 23 . – Remove exhaust system below heat shield ⇒ Rep. Gr. 26 ; Removing and installing parts of exhaust system . – Remove heat shield beneath selector mechanism. – Remove 4 nuts for selector mechanism “from above”. Torque setting for nuts: 8 Nm – Take selector mechanism out downwards. – Check selector lever cable after installing ⇒ page 30 .

Removing and installing selector lever cable up to 02.2009 AG.

Note

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

Carry out procedure as follows:

ht rig py Co t.

4.3

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

Note

by ed ris o th au

Following installation, selector lever cable must be checked for ease of movement and be adjusted. Removing – Move selector lever to position “S” position. – In order to remove selector lever cable from gearbox, first re‐ lease cable -arrows 1- and then remove it from cable support bracket -arrow 2-. Note ♦ Do not use any pliers, otherwise securing tabs on cable sup‐

port bracket could break off.

♦ Do not bend or kink selector lever cable.

4. Selector mechanism up to 02.2009

23

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Lever cable -1- off lever -3- using an open jaw spanner -2-. – Raise vehicle. To remove cable and/or selector mechanism, heat shield and, if necessary, parts of exhaust system must be removed ⇒ Rep. Gr. 26 ; Removing and installing parts of exhaust system . – Remove heat shield beneath selector mechanism. – Remove -selector housing- beneath selector lever.

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

Rep. Gr.37 - Controls, housing

thi sd o cu m en

24

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Remove locking plate for selector lever cable. Always renew locking plate.

rrectness of i t to the co nform spec at i h re o n wit in t his

-Selector housing- is pushed forwards slightly on cable --.

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

ht rig py Co t.

Prote cted by c o p yri gh t. C op yi

To remove selector lever cable, securing tab must be pushed for‐ wards in -direction of arrow 1-. agen lksw Vo by

– At same time, -pin- is pushed up with a screwdriver -arrow 2-. AG.

– Please insert -screwdriver- from underneath whilst pushing securing tab forwards.

4. Selector mechanism up to 02.2009

25

r fo ng

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

♦ -2- Push pin up

AG.

Prote cted by

Rep. Gr.37 - Controls, housing

agen lksw Vo by

c o p yri gh t . C op yi

26

ht rig py Co t.

♦ -1- Push tab forwards

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

Clarification:

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

ility ab y li an pt ce

un le

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

– Remove selector lever cable. Remove selector housing from selector lever cable. Installing Do not grease cable.

r te o iva r rp fo g n

ht rig py Co t.

– Ensure that selector lever cable is properly routed during in‐ stallation.

do c um en

– Route selector lever cable free of tension and insert in cable support bracket on gearbox. However, do not secure it there yet.

agen lksw Vo by

4. Selector mechanism up to 02.2009

27

AG.

Prote cted by c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Also clip selector lever cable into bracket. Make sure that bracket does not make contact with ATF cooler. Tighten -nuts- to 8 Nm.

– Put selector housing onto selector lever cable. – Insert selector lever cable into selector mechanism.

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

rrectness of i t to the co nf o r m spec atio h re n in wit

– Insert selector lever cable into bearing and insert pin from above, downwards through eye -direction of arrow 2-. When you have checked freedom of movement of cable ⇒ page 30 , insert locking plate.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Rep. Gr.37 - Controls, housing

ht rig py Co t.

28

thi sd o cu m en

– Attach selector lever cable with new locking plate on cable support bracket of selector mechanism.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

thi sd o cu m en

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

– Install selector housing, heat shield and exhaust system. – Adjust selector lever cable after installing ⇒ page 30 .

4. Selector mechanism up to 02.2009

29

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

4.4

Checking selector lever cable

Brief description To check ease of movement of selector lever cable, it must be removed from the gearbox and the free end must be placed so that it does not bump against anything. Then move selector lever and reinstall the selector lever cable. Then the selector lever cable must be adjusted ⇒ page 30 . Do not grease connection of selector lever cable. Carry out procedure as follows: – Move selector lever to position “P” position. – Loosen bolt -2- of selector lever cable -1-.

– Lever cable -1- from selector shaft lever -3- using an open jaw spanner -2-. olksw

agen AG V AG. by – Cable is removed from cable supportswbracket pressing does agen k not l o V catches together -arrows-. gu by

d se

ri from “P” to “S” and back to “P”. – Move selector lever repeatedly tho es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

Selector lever must

– Install selector lever cable again. – Adjust selector lever cable!

rrectness of i t to the co nform spec at i h re o n wit in t his

4.5

or ac ility ab y li an pt ce

•

au ss easily. move

ara nte e

Adjusting selector lever cable

Special tools and workshop equipment required ♦ Torque wrench -V.A.G 1331-

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

AG.

♦ The engine and/or gearbox has been removed and installed.

30

Rep. Gr.37 - Controls, housing

ht rig py Co t.

♦ The selector lever cable has been removed from the gearbox.

do c um en

The selector lever cable must always be adjusted whenever

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ♦ Parts of the assembly mounting have been removed and in‐ stalled. ♦ The cable itself or the selector mechanism has been removed and installed. ♦ The position of the engine and gearbox is shifted, for example to install it free of tension. Carry out procedure as follows: – Move selector lever to “P” position. •

Adjuster screw -2- must be “loosened”.

– Set selector shaft lever -3- to “P” on gearbox (push lever back‐ wards). WARNING

Be sure that the parking lock is engaged.

Note

Raise vehicle, to be sure that the gearbox is in “P” (parking lock engaged). It should not be possible to turn both front wheels to‐ gether in the same direction. – Gently push knob of selector lever forwards and backwards but under no circumstances must you shift out of “P”. In this way the ⇒ inner cable of the Bowden cable finds it optimal position.

rrectness of i t to the co nform spec a t i h re o n in wit thi s

4.6

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

– Tighten bolt -2- to 13 Nm.

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

Emergency release of selector lever

Do not remove knob.

– Unclip selector cover and hold to side.

do c um en

ht rig py Co t.

r te o iva r rp fo g n

– Depress brake pedal or set handbrake.

agen lksw Vo by

AG.

4. Selector mechanism up to 02.2009

31

Prote cted by

c o p yri gh t . C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Press yellow plastic part -arrow- from right to left. Lever can now be moved from position “P”.

4.7

Removing and installing knob

It is possible with all knobs that the button is pressed into the knob. Never install a knob with the button pressed in. – Before removal, pull button out past its pressure point. – Secure button with a cable tie or wire against being pressed in. – Unclip cover.

– Release knob. – Lock knob again after installing. – Press plastic part under knob back down. n AG. Volkswagen AG

does not gu ara nte eo ra c

rrectness of i t to the co nform spec at i h re o n wit in t his

– Remove transport guard of a “new” knob after releasing knob. – Pull connector from cover. – Pull off knob upwards.

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

Rep. Gr.37 - Controls, housing

ht rig py Co t.

32

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

ss

wage olks V by ed ris o th au

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 In vehicles with button -arrow- at front on knob Button -arrow- is not allowed to be pressed in when knob is being fitted and removed.

– However, should this happen, unclip knob trim upwards.

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

4.8

Checking selector mechanism

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

– Press small lever for pull rod -arrow- back into groove before installing knob.

The starter must not operate in the selector lever positions “R”, “D” or “S”.

On right-hand drive vehicles, the starter must operate in selector lever positions “P” and “N” only when the button in the gear knob is not pressed.

ht rig py Co t.

r fo ng

When selector lever is shifted to position “N” at speeds above 5 km/h, solenoid for selector lever lock must not engage and block selector lever. Selector lever can be shifted into a driving range. Prote cted by c o py rig ht . C op yi

When the vehicle is moving at speeds below 5 km/h (almost sta‐ tionary) and the selector lever is shifted to position “N”, the sole‐ noid for selector lever lock should only engage after about 1 second. Selector lever cannot be shifted out of “N” position until brake pedal is depressed. AG.

•

agen lksw Vo by

4.8.1

Selector lever in “P” position and ignition switched on

Brake pedal not depressed:

4. Selector mechanism up to 02.2009

33

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Selector lever is locked and cannot be shifted out of “P” position when the button is pressed. Solenoid for selector lever lock blocks selector lever. •

Brake pedal depressed:

un le

pe rm itte d

Brake pedal not depressed:

Selector lever is locked and cannot be shifted out of “N” position with the push button pressed. Solenoid for selector lever lock blocks selector lever. •

Brake pedal depressed:

Solenoid for selector lever lock releases selector lever. It is pos‐ sible to shift into a driving gear.

4.8.3 •

Selector lever in position “Tiptronic”

Shift selector lever into Tiptronic gate.

When the selector lever is shifted into the Tiptronic gate, the se‐ lector lever position display in the dash panel insert must change from “P R N D S” to “6 5 4 3 2 1”. Prote cted by c o py rig ht . C op yi

Ignition and light switched on

ht rig py Co t.

agen lksw Vo by

4.8.4

The respective symbol in the shift mechanism cover lights up. AG.

4.8.5

Selector lever position display

Simultaneous illumination of all selector lever position display segments indicates gearbox emergency running mode.

34

Rep. Gr.37 - Controls, housing

do c um en

r te o iva r rp fo g n

The illuminated “D” symbol in the selector mechanism cover must go out and the “+” and “-” symbols must light up.

rrectness of i t to the co nform spec a t i h re o n in wit thi s

•

Selector lever in “N” position and ignition switched on

es, in part or in w l purpos hole ercia , is n m ot com

4.8.2

ility ab y li an pt ce

. Volkswagen AG gen AG does swa k no pos‐ l o Solenoid for selector lever gu y Vlock releases selector lever. It tis b ara d gear. Slowly shift selector lever from e sible to shift into a driving nt is r o h “P” through to “S”,utchecking whether selector lever position in ee or ac a dash panel insert ss corresponds to selector lever position.

. Volkswagen AG gen AG d

s no 2005 ➤ , Jetta 2011 ➤ Golf Variant 2007Vo➤ , aGolf Variant 2010 ➤ o,eJetta lksw tg by d ran - Edition 04.2010 6-speed automatic gearboxua09G ise

tee or ac

r ho ut a ss

Selector mechanism from 03.2009 onwards es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

5

rrectness of i t to the co nf o r m spec atio h re n in wit

WARNING

Before working on vehicle with engine running, move selector lever into position “P” and apply handbrake. Selector mechanism in vehicles up to 02.2009 ⇒ page 22 .

Overview of selector mechanism in vehicles from 03.2009 onwards

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

–

thi sd o cu m en

1 - Selector cover with knob ❑ Do not remove knob without reason. For emergency release, on‐ ly the cover needs to be unclipped ⇒ page 37 . ❑ Before removing knob, pull button out past its pressure point. Secure button with cable tie or appropriate wire against being pressed in. This will prevent the button from being accidentally pressed into the knob. ❑ If button is pressed into removed handle

ht rig py Co t.

5.1

Always pull out button past the felt pressure point before installing knob.

2 - Selector lever and selector mechanism with selector lever cable ❑ With selector lever lock solenoid -N110❑ Selector lever cable is not greased ❑ Removing and installing ⇒ page 36 ❑ Checking ⇒ page 30 ❑ Adjusting ⇒ page 30 3 - Bolt ❑ 8 Nm 4 - Hexagon flange nut ❑ 8 Nm ❑ Qty. 4 5 - Selector lever housing 6 - Selector lever cable ❑ Is not allowed to be removed from selector mechanism and is renewed jointly as one component 7 - Gearbox

5. Selector mechanism from 03.2009 onwards

35

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

5.2

Removing and installing selector lever and selector mechanism with selector lever cable from 03.2009 onwards Note

♦ Selector mechanism and selector lever cable are not allowed

to be separated from one another. Both are removed together.

♦ Following installation, selector lever cable must be checked

for ease of movement and be adjusted.

Carry out procedure as follows: – Move selector lever to position “P” position. – Remove selector lever handle ⇒ page 32 . – Remove centre console ⇒ Rep. Gr. 68 ; Compartments, cov‐ ers and trims . – Pull connector off selector mechanism. – Remove 4 bolts.

ility ab y li an pt ce

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

Torque setting 8 Nm.

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

– In order to remove selector lever cable from gearbox, first re‐ lease cable -arrows 1- and then remove it from cable support bracket -arrow 2-. Note

♦ Do not use any pliers, otherwise securing tabs on cable sup‐ ♦ Do not bend or kink selector lever cable.

– Remove heat shield beneath selector mechanism.

36

Rep. Gr.37 - Controls, housing

AG.

– Remove exhaust system below heat shield ⇒ Rep. Gr. 26 ; Removing and installing parts of exhaust system .

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

– Raise vehicle.

ht rig py Co t.

– Lever cable -1- off lever -3- using an open jaw spanner -2-.

thi sd o cu m en

port bracket could break off.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Remove selector mechanism. Install in reverse order of removal. – Install heat shield beneath selector mechanism. – Install parts of exhaust system ⇒ Rep. Gr. 26 ; Removing and installing parts of exhaust system . – Adjust selector lever cable after installing ⇒ page 30 .

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

r fo ng

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

Lever can now be moved from position “P”.

ht rig py Co t.

– Press yellow plastic wedge.

un le

Emergency release of selector lever

ility ab y li an pt ce

5.3

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

5. Selector mechanism from 03.2009 onwards

37

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

6

Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Var‐ iant 2007 ▸, Jetta Wagon 2008 ▸

Removing gearbox, vehicles with 1.6 l - 75 kW and 2.0 l - 110 kW (FSI) engines ⇒ page 38 Installing gearbox, vehicles with 1.6 l - 75 kW and 2.0 l - 110 kW (FSI) engines ⇒ page 45 Removing gearbox, vehicles with 2.5 l - 110 kW engine ⇒ page 45 Installing gearbox, vehicles with 2.5 l - 110 kW engine ⇒ page 53 Torque settings ⇒ page 54

6.1

Removing gearbox, vehicles with 1.6 l 75 kW and 2.0 l - 110 kW (FSI) engines

– Before beginning with removal, “if possible” print out a diag‐ . Volkswagen AG gen AG does nosis log. Before sending back removed gearbox in the usual Volkswa not gu y b ara manner, secure log to gearbox. ed Brief description

nte eo ra c

ris ho ut a ss

un le

pe rm itte d

ility ab y li an pt ce

The gearbox is removed downwards as a unit. The engine re‐ mains in the vehicle.

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

Battery, battery carrier, air filter and engine cover are removed “from above”. Engine and gearbox must then be supported so that left assembly mounting can be removed. Noise insulation is removed and drive shafts are pressed off “from below”. Gearbox is lowered using gearbox jack.

AG.

Rep. Gr.37 - Controls, housing

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

38

do c um en

r te o iva r rp fo g n

The subframe is not to be removed.

ht rig py Co t.

Note

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Special tools and workshop equipment required ♦ Engine and gearbox jack V.A.G 1383 A♦ Torque wrench -V.A.G 1332♦ Gearbox support -3282♦ Adjustment plate -3282 /36♦ Hose clamps to 25 mm Ø -3094-

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

r fo ng

ht rig py Co t.

♦ Insert -V/175-

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

♦ Socket -T10179-

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

39

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ♦ Support bracket -10 - 222 A-

♦ Adapter -10 - 222 A /13-

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

♦ Tensioning strap -T10038-

AG.

Prote cted by

– Move selector lever to position “P” position. – Remove battery and battery tray ⇒ Rep. Gr. 27 ; Disconnect‐ ing and connecting battery; Removing and installing battery . – Remove engine cover and air filter with intake hose.

40

Rep. Gr.37 - Controls, housing

agen lksw Vo by

c o p yri gh t. C op yi

Carry out procedure as follows:

ht rig py Co t.

– Before beginning with removal, “if possible” print out a diag‐ nosis log. Before sending back removed gearbox in the usual manner, secure log to gearbox.

do c um en

Following descriptions show “automatic gearbox 09G” with 2-litre petrol engine (FSI). Deviations to other engine types are minimal. However, torque settings for bolting gearbox to engine go into detail “as usual” (large and small engines, FSI and multi-point in‐ jection engines).

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – In order to remove selector lever cable from gearbox, first re‐ lease cable -arrows 1- and then remove it from cable support bracket -arrow 2-. Note ♦ Do not use any pliers, otherwise securing tabs on cable sup‐

port bracket could break off.

♦ Do not bend or kink selector lever cable.

ility ab y li an pt ce

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

un le

– Lever

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra cable -1- off lever -3- using an open jaw spanner -2-. a c s s

– Tighten hose clamps up to Ø 25 mm -3094- on hoses and remove hoses from ATF cooler. – Disconnect electrical connections to gearbox and starter.

do c um en

ht rig py Co t.

r te o iva r rp fo g n

– Remove upper starter motor bolt.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

– Set up support bracket -10 - 222 A- and support engine with gearbox. Do not raise. – Remove upper engine/gearbox connecting bolts. Bolts may be installed with a socket -T10179- . However, note lower torque setting when tightening ⇒ page 54 .

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

41

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – If present, remove earth strap from bracket -A-. – Remove 2 securing bolts for gearbox mounting on bracket -A- and 4 bolts for bracket on gearbox. The bracket is removed later.

– Depress brake pedal to remove bolt for left drive shaft -arrow- (second mechanic required). Note

After this, do not set vehicle on the ground any more ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts . – Raise vehicle. – Remove noise insulation tray. – Remove vacuum pump with bracket and lines. “The pump is located near the ATF filler tube.” – If not already done, now remove electrical connectors from agen AG. Volkswagen AG do es n ksw gearbox. ot g Vol y db

ua ran tee

ss

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

– Remove ⇒ pendulum support, first bolt -A- and then bolts -B-. Note

or ac ility ab y li an pt ce

un le

e ris – Remove starter ⇒ Rep. Gr. 27 ; Removing andhoinstalling t u starter . a

When installing, first tighten bolts -B-, then bolt -A-, torque set‐ tings ⇒ Rep. Gr. 40 ; Assembly overview - subframe, anti-roll bar, suspension links .

– Unbolt suspension link from wheel bearing housing on both sides.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Rep. Gr.37 - Controls, housing

ht rig py Co t.

42

do c um en

r te o iva r rp fo g n

Torque settings ⇒ Rep. Gr. 40 ; Assembly overview - subframe, anti-roll bar, suspension links .

Golf

AG. Volkswagen AG d agen oes ksw not l o Variant 2007 b➤ gu ➤ , Jetta 2011 ➤ y V, Golf Variant 2010 ➤ , Jetta 2005 ara d ise 6-speed automatic gearbox 09G -ntEdition 04.2010 r ee o h t or u a a c ss

– Press both drive shafts out of gearbox. This procedure is de‐ scribed in ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

ht rig py Co t.

r fo ng

– Remove left drive shaft ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

un le

ility ab y li an pt ce

– If present, remove heat shield above right drive shaft -arrows-.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

– Raise right shaft as far as possible and secure in this position.

– Now remove assembly mounting bracket. To do this, lower engine and gearbox slightly via support bracket -10 - 222 Aspindles. 4 turns are sufficient. – If exhaust system retainer is present on gearbox, remove it. – Remove lower engine/gearbox connecting bolts. – Leave an easily accessible bolt installed for safety. – Start with two lower bolts.

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

43

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Note

On some smaller engines up to 1.6 litres, one of the lower -bolts- can be backed out of the gearbox but not removed from the hole. – If this bolt has to be removed then remove front exhaust pipe ⇒ Rep. Gr. 26 ; Removing and installing parts of exhaust system . n AG. Volkswagen AG do es n ot g ua ran tee or ac

The hole for removing the torque converter nut is covered with a olkswage yV rubber cap on the rear of the engine. db

ility ab y li an pt ce

e ris tho u a ss

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

– Remove this cap.

– Remove six -torque converter nuts- with insert -V/175- .

Continue turning the engine carefully!

rrectness of i t to the co nform spec at i h re o n wit in t his

Note

– Before you now remove final connecting bolt, support gearbox with engine and gearbox jack -V.A.G 1383 A- , gearbox sup‐ port -3282- and adjustment plate -3282 /36- . – Secure gearbox to gearbox support -3282- using bolt -1-.

Prote cted by

Rep. Gr.37 - Controls, housing

AG.

44

agen lksw Vo by

c o p yri gh t . C op yi

– Note clearance from subframe when lowering. If necessary, readjust gearbox support -3282- slightly.

ht rig py Co t.

– Press gearbox off engine while simultaneously pressing tor‐ que converter out of drive plate of engine.

do c um en

– Only now is the final bolt removed.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Note ♦ Pay attention to torque converter. It must be removed together

with gearbox. Secure torque converter to prevent it from falling out.

♦ Keep in mind that if a new gearbox is installed, parts such as

cable support bracket and retainer for gate selector cable must be transferred.

6.2

Installing gearbox, vehicles with 1.6 l 75 kW and 2.0 l - 110 kW (FSI) engines

– Check whether dowel sleeves are pressed into engine flange. – Check seat of intermediate plate between engine and gear‐ box. The plate must make contact with the engine along its entire perimeter when it is pressed gently with both hands against the engine. If the top does not contact the engine, it is not properly engaged in the engine block. Continue installation in reverse order of removal. The engine and gearbox should be mounted tension-free in the assembly mounting. The correct procedure is described in ⇒ Rep. Gr. 10 ; Removing and installing engine; Notes on. Vinstallation . olkswag AG agen

w olks – Renew all bolts on left assembly mounting. yV

b ed

ris – First screw in all bolts by hand. ho

t au

un le

pe rm itte d

es, in part or in w l purpos hole ercia , is n m ot com

rrectness of i t to the co nform spec a t i h re o n in wit thi s

Two bolts -2- for securing bracket to gearbox mounting can be tightened by inserting a screwdriver between the two bolts to ad‐ just to “previous seating”. These two larger bolts are tightened to 60 Nm + 90°.

ility ab y li an pt ce

s When installing, first screw sbracket -A- onto gearbox curing bolts -1-, tighten to 40 Nm and 90° further.

en AG does not gu ara nte eo ra c using se‐

Torque settings, gearbox to engine ⇒ page 54 . – Adjust selector lever cable ⇒ page 30 . – After installing, check ATF level ⇒ page 77 . – Carry out basic settings. To do this – Connect vehicle diagnosis, testing and information system VAS 5051- and then select “Perform basic settings” under Guided functions .

r te o iva r rp fo g n

– Before beginning with removal, “if possible” print out a diag‐ nosis log. Before sending back removed gearbox in the usual manner, secure log to gearbox. agen lksw Vo by

Prote cted by

c o p yri gh t. C op yi

Brief description

do c um en

Removing gearbox, vehicles with 2.5 l, 110 kW engine ht rig py Co t.

6.3

The gearbox is removed downwards separately. The engine re‐ mains in the vehicle. AG.

Battery, battery carrier, air filter and engine cover are removed “from above”. Engine and gearbox must then be supported so that left assembly mounting can be removed.

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

45

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 . Volkswage

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

n AG d AG agen oes ksw not l o V gu off “from y Noise insulation isdremoved and drive shafts are pressed b ara nte iseis lowered using gearbox jack. below”. Gearbox r o eo h t u ra a c s s

Note

The subframe is not to be removed.

rrectness of i t to the co nform spec at i h re o n wit in t his

Special tools and workshop equipment required ♦ Engine and gearbox jack V.A.G 1383 A♦ Insert -V/175♦ Gearbox support -3282♦ Wedge -T10161♦ Torque wrench -V.A.G 1332♦ Adjustment plate -3282 /36-

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Rep. Gr.37 - Controls, housing

do c um en

46

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ♦ Support bracket -10 - 222 A♦ Adapter -10 - 222 A /8♦ Adapter -10 - 222 A /7♦ Hook -10 - 222 A /10♦ Adapter -10 - 222 A /3-

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

♦ Tensioning strap -T10038-

do c um en

r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

♦ Shackle -10 - 222 A /12-

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

Carry out procedure as follows: – Before beginning with removal, “if possible” print out a diag‐ nosis log. Before sending back removed gearbox in the usual manner, secure log to gearbox. – Move selector lever to position “P” position. – Raise vehicle.

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

47

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Depress brake pedal to remove bolt for left drive shaft -arrow- (second mechanic required). Note

un le

– Pull off hoses -arrows- and remove intake hose from throttle valve unit. – Remove battery and battery tray ⇒ Rep. Gr. 27 ; Disconnect‐ ing and connecting battery; Removing and installing battery .

port bracket could break off.

♦ Do not bend or kink selector lever cable.

– Lever cable -1- off lever -3- using an open jaw spanner -2-. – Disconnect electrical connections to gearbox and starter. ♦ Multifunction switch ♦ Starter motor ♦ Earth strap to bracket

48

Rep. Gr.37 - Controls, housing

AG.

♦ Do not use any pliers, otherwise securing tabs on cable sup‐

agen lksw Vo by

Prote cted by c o p yri gh t. C op yi

Note

ht rig py Co t.

r fo ng

– In order to remove selector lever cable from gearbox, first re‐ lease cable -arrows 1- and then remove it from cable support bracket -arrow 2-.

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

– Remove engine cover and air filter.

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o gu yV b⇒ ara After this, do not set vehicle on the ground any more Rep. Gr. d e nte is r 40 ; Repairing drive shafts; Removing and installing drive shafts . o eo h ut ra a c s s

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Remove cable retainer -1- from starter bolt -arrow-. – Remove upper starter motor bolt. – Remove upper engine/gearbox connecting bolts. To support engine and gearbox:

– Remove cables -1- from transportation bracket -3-. – Unbolt transportation bracket -3- from engine -2- and pull out of eye -arrow-.

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

– Extend right hook -10 - 222 A /10- using adapter -10 - 222 A / 7- . The hook faces downwards and will later be hooked into the en‐ gine block. – Remove noise insulation tray.

– Remove lower part of left wheel housing liner.

ht rig py Co t.

r fo ng

– If present, remove heat shield above right drive shaft -arrows-.

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

– Set up support device -10 - 222 A- .

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

ility ab y li an pt ce

un le

– Attach a shackle -10 - 222 A /12- in “this” eye.

49

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Unbolt suspension link from wheel bearing housing on both sides.

– Press both drive shafts out of gearbox. This procedure is de‐ scribed in ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts . – Remove left drive shaft ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

– Raise right shaft as far as possible and secure in this position.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Rep. Gr.37 - Controls, housing

ht rig py Co t.

50

do c um en

r te o iva r rp fo g n

– Now pull electrical connectors -1- and -2- off gearbox.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Pull connector beneath starter -1- out of retainer and separate. – Unbolt retainer from lower starter bolt.

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

– Remove lower starter bolt and remove starter.

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

– Remove ⇒ pendulum support, first bolt -A- and then bolts -B-.

do c um en

– Turn cap -1- in -direction of arrow- and remove.

ht rig py Co t.

– Drain coolant.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

– Remove six -torque converter nuts- with insert -V/175- . Note

Continue turning the engine carefully!

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

51

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Hook adapter -10 - 222 A /7- into engine block. – Pull coolant hoses off ATF cooler. Tighten right spindle one turn (more is not

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or necessary). u ac a ss

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

– Support engine and gearbox with left spindle. Do not raise.

– Remove 2 securing bolts for gearbox mounting on bracket -A- and 4 bolts for bracket on gearbox.

Prote cted by

– Before you now remove final connecting bolt, support gearbox with engine and gearbox jack -V.A.G 1383 A- , gearbox sup‐ port -3282- and adjustment plate -3282 /36- . – Secure gearbox to gearbox support -3282- using bolt -1-. – Only now is the final bolt removed. – Press gearbox off engine while simultaneously pressing tor‐ que converter out of drive plate of engine. – Note clearance from subframe when lowering. If necessary, readjust gearbox support -3282- slightly.

52

Rep. Gr.37 - Controls, housing

AG.

– Leave an easily accessible bolt installed for safety.

agen lksw Vo by

c o p yri gh t . C op yi

– Remove lower engine/gearbox connecting bolts.

ht rig py Co t.

4 turns are sufficient.

do c um en

– Now remove assembly mounting bracket. To do this, lower engine and gearbox slightly via left spindle of support bracket -10 - 222 A- .

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

rrectness of i t to the co nf o r m spec atio h re n in wit

Note

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

♦ Pay attention to torque converter. It must be removed together

with gearbox. Secure torque converter to prevent it from falling out.

♦ Keep in mind that if a new gearbox is installed, parts such as

cable support bracket and retainer for gate selector cable must be transferred.

6.4

– Check whether dowel sleeves are pressed into engine flange.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Continue installation in reverse order of removal.

ht rig py Co t.

– Check seat of intermediate plate between engine and gear‐ box. The plate must make contact with the engine along its entire perimeter when it is pressed gently with both hands against the engine. If the top does not contact the engine, it is not properly engaged in the engine block.

thi sd o cu m en

Installing gearbox, vehicles with 2.5 l, 110 kW engine

The engine and gearbox should be mounted tension-free in the assembly mounting. The correct procedure is described in ⇒ Rep. Gr. 10 ; Removing and installing engine; Notes on installation . – Renew all bolts on left assembly mounting. – First screw in all bolts by hand. When installing, first screw bracket -A- onto gearbox using se‐ curing bolts -1-, tighten to 40 Nm and 90° further. Two bolts -2- for securing bracket to gearbox mounting can be tightened by inserting a screwdriver between the two bolts to ad‐ just to “previous seating”. These two larger bolts are tightened to 60 Nm + 90°. Torque settings, gearbox to engine ⇒ page 54 . – Adjust selector lever cable ⇒ page 30 . – After installing, check ATF level ⇒ page 77 . – Carry out basic settings. To do this – Connect vehicle diagnosis, testing and information system VAS 5051- and then select “Perform basic settings” under Guided functions .

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

53

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

6.5

olkswagen AG Torque settings, gearbox toagengine en AG. V d

oes not gu ara nte eo ra c

w olks

yV Vehicles with 1.6 l - 75 kW and 2.0 l - 110 d b kW (FSI) engines ise ⇒ page 54 r o h ut

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

6.5.1

ility ab y li an pt ce

a Vehicles with 2.5 l - 110 kW engine ss ⇒ page 55

Torque settings, vehicles with 1.6 l - 75 kW and 2.0 l - 110 kW (FSI) engines rrectness of i t to the co nform spec at i h re o n wit in t his

1 - Direction of travel

A - Bolt for 2.0 l - 110 kW (FSI) engine B - Bolt for 1.6 l -75 kW engine

- Drive plate to torque convert‐ er ❑ 60 Nm ❑ Qty. 6; remove and in‐ stall with insert -V/175- .

AG.

Rep. Gr.37 - Controls, housing

agen lksw Vo by

54

Prote cted by c o py rig ht . C op yi

- 2 dowel sleeves in engine -arrows-

ht rig py Co t.

- M10 bolts ⇒ M10 ❑ 40 Nm ❑ These bolts are located in lower flange

do c um en

- M12 bolts ⇒ M12 ❑ 80 Nm ❑ 65 Nm if you use socket -T10179-

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Make sure that bracket does not make contact with ATF cool‐ er. -Nuts- 8 Nm

rrectness of i t to the co nf o r m spec atio h re n in wit

1 - Direction of travel

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

Torque settings, vehicles with 2.5 l - 110 kW engine

ility ab y li an pt ce

6.5.2

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

- Drive plate to torque convert‐ er ❑ 60 Nm ❑ Qty. 6; remove and in‐ stall with insert -V/175- .

- M12 bolts ⇒ M12 ❑ 80 Nm ❑ 65 Nm if you use socket -T10179-

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

- 2 dowel sleeves in engine -arrows-

thi sd o cu m en

- M10 bolts ⇒ M10 ❑ 40 Nm ❑ These bolts are located in lower flange

6. Removing and installing gearbox, Jetta 2005 ▸, Bora 2006 ▸, Golf Variant 2007 ▸, Jetta Wagon 2008 ▸

55

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Make sure that bracket does not make contact with ATF cool‐ er.

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Rep. Gr.37 - Controls, housing

ht rig py Co t.

56

do c um en

r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

-Nuts- 8 Nm

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

Removing and installing gearbox, Jetta 2011 ▸

ility ab y li an pt ce

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

7

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

Removing gearbox, Jetta 2011 with 2.0 l - 85 kW engine ⇒ page 57

rrectness of i t to the co nf o r m spec atio h re n in wit

Installing gearbox, Jetta 2011 with 2.0 l - 85 kW engine ⇒ page 63 Removing gearbox, Jetta 2011 with 2.5 l - 125 kW engine ⇒ page 63 Installing gearbox, Jetta 2011 with 2.5 l - 125 kW engine ⇒ page 72 Torque settings ⇒ page 72

7.1

Removing gearbox, Jetta 2011 with 2.0 l - 85 kW engine

– Before beginning with removal, “if possible” print out a diag‐ nosis log. Before sending back removed gearbox in the usual manner, secure log to gearbox.

agen lksw Vo by

AG.

♦ Gearbox support -3282-

Prote cted by c o p yri gh t. C op yi

♦ Insert -V/175-

ht rig py Co t.

♦ Engine and gearbox jack V.A.G 1383 A-

thi sd o cu m en

Special tools and workshop equipment required

♦ Wedge -T10161♦ Torque wrench -V.A.G 1332♦ Adjustment plate -3282 /36-

7. Removing and installing gearbox, Jetta 2011 ▸

57

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ♦ Support bracket -10 - 222 A-

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

rrectness of i t to the co nform spec at i h re o n wit in t his

♦ Hose clamps to 25 mm -3094-

Prote cted by

– Remove air filter. – Remove battery and battery tray ⇒ Rep. Gr. 27 ; Disconnect‐ ing and connecting battery; Removing and installing battery .

58

Rep. Gr.37 - Controls, housing

AG.

– Move selector lever to position “P” position.

agen lksw Vo by

c o p yri gh t . C op yi

Carry out procedure as follows:

ht rig py Co t.

♦ Engine support basic set -T40091-

do c um en

♦ Tensioning strap -T10038-

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – In order to remove selector lever cable from gearbox, first re‐ lease cable -arrows 1- and then remove it from cable support bracket -arrow 2-. Note ♦ Do not use any pliers, otherwise securing tabs on cable sup‐

port bracket could break off.

♦ Do not bend or kink selector lever cable.

ility ab y li an pt ce

– Tighten hose clamps up to Ø 25 mm -3094- on hoses and remove hoses from ATF cooler. – Disconnect electrical connections to gearbox and starter. ♦ Multifunction switch ♦ Starter motor

thi sd o cu m en

– Remove upper starter motor bolt.

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

–

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d Lever cable -1off lever -3using an open jaw spanner -2-. e nte is r o eo h t ra au c ss

– Remove plenum chamber cover ⇒ Rep. Gr. 50 ; Plenum chamber cover; Removing and installing plenum chamber cover . ht rig py Co t.

agen lksw Vo by

Prote cted by c o p yri gh t. C op yi

– Set up support bracket -10 - 222 A- and support engine and gearbox. Do not raise. -T40091/3-

2-

-10-222 A /31-1-

3-

-10-222 A /12-

4-

-10-222 A /3-

5-

-10-222 A /31-4-

6-

-10-222 A /31-3-

7-

-T40091/1-

8-

-10-222 A /18-

9-

-10-222 A /31-2-

AG.

1-

– Remove upper engine/gearbox connecting bolts.

7. Removing and installing gearbox, Jetta 2011 ▸

59

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – If present, remove earth strap from bracket -A-. – Remove 2 securing bolts for gearbox mounting on bracket -A- and 4 bolts for bracket on gearbox.

– Depress brake pedal to remove bolt for left drive shaft -arrow- (second mechanic required). Note

After this, do not set vehicle on the ground any more ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts . – Raise vehicle and remove front wheels. – Remove noise insulation tray.

– Now pull electrical connectors -1- and -2- off gearbox. – Remove starter ⇒ Rep. Gr. 27 ; Removing and installing starter . – Separate exhaust system at double clamp and remove ex‐ haust pipe bracket from subframe ⇒ Rep. Gr. 26 ; Removing and installing parts of exhaust system .

– Remove ⇒ pendulum support, first bolt -A- and then bolts -B-. Note

When installing, first tighten bolts -B-, then bolt -A-, torque set‐ tings ⇒ Rep. Gr. 40 ; Assembly overview - subframe, anti-roll bar, suspension links .

60

Rep. Gr.37 - Controls, housing

AG.

Continuation for all vehicles

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

– Remove brackets with power assisted steering line from gear‐ box.

ht rig py Co t.

For vehicles with power steering

r fo ng

– Remove front left wheel housing liner ⇒ Rep. Gr. 66 ; Wheel housing liner; front wheel housing liner .

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

The bracket is removed later.

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Unbolt suspension link from wheel bearing housing on both sides.

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

– If present, remove heat shield above right drive shaft -arrows-.

– Press both drive shafts out of gearbox. This procedure is de‐ scribed in ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts . r fo ng

ht rig py Co t.

– Remove left drive shaft ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

Torque settings ⇒ Rep. Gr. 40 ; Assembly overview - subframe, anti-roll bar, suspension links .

agen lksw Vo by

Prote cted by

AG.

c o p yri gh t. C op yi

– Raise right shaft as far as possible and secure in this position.

7. Removing and installing gearbox, Jetta 2011 ▸

61

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Now remove assembly mounting bracket. To do this, lower engine and gearbox slightly via support bracket -10 - 222 Aspindles. 4 turns are sufficient. – Remove lower connecting bolts between engine and gearbox. – Leave an easily accessible bolt installed for safety. The torque converter nut bore is concealed with a rubber cap on the rear of the engine.

Continue turning the engine carefully!

– Before you now remove final connecting bolt, support gearbox with engine and gearbox jack -V.A.G 1383 A- , gearbox sup‐ port -3282- and adjustment plate -3282 /36- . – Secure gearbox to gearbox support -3282- using nut -1- at double bolt. – Only now is the final bolt removed. r fo ng

Prote cted by c o py rig ht . C op yi

– When lowering gearbox, guide it past power assisted steering line and past subframe. If necessary, readjust gearbox support -3282- slightly. AG.

Rep. Gr.37 - Controls, housing

agen lksw Vo by

62

ht rig py Co t.

– Press gearbox off engine while simultaneously pressing tor‐ que converter out of drive plate of engine.

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

Note

ility ab y li an pt ce

– Remove six -torque

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s converter nuts- with insert -V/175- . s un le

– Remove this cap.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Note ♦ Pay attention to torque converter. It must be removed together

with gearbox. Secure torque converter to prevent it from falling out.

♦ Keep in mind that if a new gearbox is installed, parts such as

cable support bracket and retainer for gate selector cable must be transferred.

7.2

Installing gearbox, Jetta 2011 with 2.0 l - 85 kW engine

– Check whether dowel sleeves are pressed into engine flange. – Check seat of intermediate plate between engine and gear‐ box. The plate must make contact with the engine along its entire perimeter when it is pressed gently with both hands against the engine. If the top does not contact the engine, it is not properly engaged in the engine block. . Volkswag l ot g o V by ara d should The engine and gearbox be mounted tension-free in uthe e n is or correct procedure is described in ⇒ Rep.tee assembly mounting.thThe or u ac a Gr. 10 ; Removing and installing engine; Notes on installation . ss

ility ab y li an pt ce

– Renew all bolts on left assembly mounting. – First screw in all bolts by hand.

Two bolts -2- for securing bracket to gearbox mounting can be tightened by inserting a screwdriver between the two bolts to ad‐ just to “previous seating”. These two larger bolts are tightened to 60 Nm + 90°. Torque settings, gearbox to engine ⇒ page 73 . – Adjust selector lever cable ⇒ page 30 . – After installing, check ATF level ⇒ page 77 . – Carry out basic settings. To do this – Connect vehicle diagnosis, testing and information system VAS 5051- and then select “Perform basic settings” under Guided functions .

Removing gearbox, Jetta 2011 with 2.5 l - 125 kW engine

ht rig py Co t.

agen lksw Vo by

Prote cted by c o p yri gh t. C op yi

7.3

rrectness of i t to the co nform spec at i h re o n wit in t his

When installing, first screw bracket -A- onto gearbox using se‐ curing bolts -1-, tighten to 40 Nm and 90° further.

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

en AG Continue installation in reverse order agen of removal. AG does ksw n

– Before beginning with removal, “if possible” print out a diag‐ nosis log. Before sending back removed gearbox in the usual manner, secure log to gearbox. AG.

Brief description The gearbox is removed downwards separately. The engine re‐ mains in the vehicle. Battery, battery carrier, air filter and engine cover are removed “from above”. Engine and gearbox must then be supported so that left assembly mounting can be removed.

7. Removing and installing gearbox, Jetta 2011 ▸

63

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Noise insulation is removed and drive shafts are pressed off “from below”. Gearbox is lowered using gearbox jack. Note

The subframe is not to be removed. Special tools and workshop equipment required ♦ Engine and gearbox jack V.A.G 1383 A♦ Insert -V/175-

rrectness of i t to the co nform spec a t i h re o n in wit thi s

un le

es, in part or in w l purpos hole ercia , is n m ot com

♦ Torque wrench -V.A.G 1332-

pe rm itte d

♦ Wedge -T10161-

ility ab y li an pt ce

♦ Gearbox support -3282-

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

AG.

Rep. Gr.37 - Controls, housing

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

64

ht rig py Co t.

♦ Support bracket -10 - 222 A-

do c um en

r te o iva r rp fo g n

♦ Adjustment plate -3282 /36-

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ♦ Hose clamps to 25 mm -3094-

♦ Tensioning strap -T10038-

♦ Engine support basic set -T40091-

Carry out procedure as follows: – Move selector lever to position “P” position. – Remove engine cover and air filter. – Pull off hoses -arrows- and remove intake hose from throttle valve unit.

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

thi sd o cu m en

7. Removing and installing gearbox, Jetta 2011 ▸

65

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010AG➤. V,olJetta ➤ , Jetta 2011 ➤ kswage2005 n AG d agen oes wEdition 6-speed automatic gearbox 09G 04.2010 s k no l o t gu ara nte eo ra c

ility ab y li an pt ce

rrectness of i t to the co nf o r m spec atio h re n in wit

– In order to remove selector lever cable from gearbox, first re‐ lease cable -arrows 1- and then remove it from cable support bracket -arrow 2-. Note

♦ Do not use any pliers, otherwise securing tabs on cable sup‐

port bracket could break off.

agen lksw Vo by

Prote cted by

c o p yri gh t . C op yi

– Lever cable -1- off lever -3- using an open jaw spanner -2-. AG.

– Tighten hose clamps up to Ø 25 mm -3094- on hoses and remove hoses from ATF cooler. – Disconnect electrical connections to gearbox and starter. ♦ Multifunction switch ♦ Starter motor

66

Rep. Gr.37 - Controls, housing

ht rig py Co t.

♦ Do not bend or kink selector lever cable.

thi sd o cu m en

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

–

V by ed s i r Remove battery and battery ttray ho ⇒ Rep. Gr. 27 ; Disconnect‐ uRemoving and installing battery . a ing and connecting battery; ss

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Remove cable retainer -1- from starter bolt -arrow-. – Remove upper starter motor bolt. – Remove upper engine/gearbox connecting bolts. – Remove plenum chamber cover ⇒ Rep. Gr. 50 ; Plenum chamber cover; Removing and installing plenum chamber cover . To support engine and gearbox:

– Remove cables -1- from transportation bracket -3-. – Unbolt transportation bracket -3- from engine -2- and pull out of eye -arrow-. – Attach a shackle -10 - 222 A /12- in “this” eye.

-T40091 /1-

3-

-10-222 A /31-1-

4-

-10-222 A /12-

5-

-10-222 A /31-4-

6-

-10-222 A /31-3-

7-

-10-222 A /3-

8-

-10-222 A /7-

9-

-10-222 A /31-2-

10 - -10-222 A /10-

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

2-

– Extend right hook -10 - 222 A /10- -no. 10- with adapter -10 222 A /7- -no. 8-.

ht rig py Co t.

r fo ng

The hook faces downwards and will later be hooked into the en‐ gine block.

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

-T40091 /3-

ility ab y li an pt ce

1-

un le

– Set up support bracket -10 - 222 A- and support engine and gearbox. Do not raise.

agen lksw Vo by

AG.

7. Removing and installing gearbox, Jetta 2011 ▸

67

Prote cted by

c o p yri gh t . C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Depress brake pedal to remove bolt for left drive shaft AG. Volkswagen AG d -arrow- (second mechanic required). agen oes n lksw Note ss

ot g ua ran tee or ac

o yV db e ris tho au

un le

pe rm itte d

ility ab y li an pt ce

After this, do not set vehicle on the ground any more ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

– Raise vehicle and remove front wheels. – Remove noise insulation tray.

– Remove front left wheel housing liner ⇒ Rep. Gr. 66 ; Wheel housing liner; front wheel housing liner . For vehicles with power steering

– Remove brackets with power assisted steering line from gear‐ box. Continuation for all vehicles

– Unbolt suspension link from wheel bearing housing on both sides.

Rep. Gr.37 - Controls, housing

AG.

68

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

– If present, remove heat shield above right drive shaft -arrows-.

ht rig py Co t.

Torque settings ⇒ Rep. Gr. 40 ; Assembly overview - subframe, anti-roll bar, suspension links .

do c um en

r te o iva r rp fo g n

– Separate exhaust system at double clamp and remove ex‐ haust pipe bracket from subframe ⇒ Rep. Gr. 26 ; Removing and installing parts of exhaust system .

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Press both drive shafts out of gearbox. This procedure is de‐ scribed in ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts . – Remove left drive shaft ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

– Raise right shaft as far as possible and secure in this position.

– Now pull electrical connectors -1- and -2- off gearbox.

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

rrectness of i t to the co nform spec at i h re o n wit in t his

– Pull connector beneath starter -1- out of retainer and separate. – Unbolt retainer from lower starter bolt.

– Remove lower starter bolt and remove starter ⇒ Rep. Gr. 27 ; Removing and installing starter .

do c um en

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

7. Removing and installing gearbox, Jetta 2011 ▸

69

c o p yri gh t . C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Remove ⇒ pendulum support, first bolt -A- and then bolts -B-.

ility ab y li an pt ce

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

– Turn cap -1- in direction of arrow

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or uremove. and ac a ss

– Remove six -torque converter nuts- with insert -V/175- . Note

Continue turning the engine carefully!

Prote cted by

Rep. Gr.37 - Controls, housing

AG.

70

agen lksw Vo by

c o p yri gh t . C op yi

– Support engine and gearbox with left spindle. Do not raise.

ht rig py Co t.

Tighten right spindle one turn (more is not necessary).

do c um en

– Hook adapter -10 - 222 A /7- into engine block.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – If present, remove earth strap from bracket -A-. – Remove 2 securing bolts for gearbox mounting on bracket -A- and 4 bolts for bracket on gearbox.

– Now remove assembly mounting bracket. To do this, lower engine and gearbox slightly via support bracket -10 - 222 Aspindles. 4 turns are sufficient. – Remove lower connecting bolts between engine and gearbox. – Leave an easily accessible bolt installed for safety.

– Before you now remove final connecting bolt, support gearbox with engine and gearbox jack -V.A.G 1383 A- , gearbox sup‐ port -3282- and adjustment plate -3282 /36- . – Secure gearbox to gearbox support -3282- using nut -1- at n AG. Volkswagen AG do double bolt. e wage

s no t gu ara nte eo ra c

pressing tor‐

ility ab y li an pt ce

un le

–

r fo ng

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

– When lowering gearbox, guide it past power assisted steering line and past subframe. If necessary, readjust gearbox support -3282- slightly.

ht rig py Co t.

olks yV db e ris ho Press gearbox off engine while simultaneously ut a que converter out of drive platessof engine.

– Only now is the final bolt removed.

agen lksw Vo by

AG.

7. Removing and installing gearbox, Jetta 2011 ▸

71

Prote cted by c o py rig ht . C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

♦ Keep in mind that if a new gearbox is installed, parts such as

7.4

Installing gearbox, Jetta 2011 with 2.5 l - 125 kW engine

– Check whether dowel sleeves are pressed into engine flange. – Check seat of plate between engine and gearbox. The plate must make contact with the engine along its entire perimeter when it is pressed gently with both hands against the engine. If the top does not contact the engine, it is not properly en‐ gaged in the engine block. Continue installation in reverse order of removal. The engine and gearbox should be mounted tension-free in the assembly mounting. The correct procedure is described in ⇒ Rep. Gr. 10 ; Removing and installing engine; Notes on installation . agen lksw Vo by

Prote cted by

c o p yri gh t. C op yi

AG.

– First screw in all bolts by hand.

ht rig py Co t.

– Renew all bolts on left assembly mounting.

When installing, first screw bracket -A- onto gearbox using se‐ curing bolts -1-, tighten to 40 Nm and 90° further. Two bolts -2- for securing bracket to gearbox mounting can be tightened by inserting a screwdriver between the two bolts to ad‐ just to “previous seating”. These two larger bolts are tightened to 60 Nm + 90°. Torque settings, gearbox to engine ⇒ page 72 . – Adjust selector lever cable ⇒ page 30 . – After installing, check ATF level ⇒ page 77 . – Carry out basic settings. To do this – Connect vehicle diagnosis, testing and information system VAS 5051- and then select “Perform basic settings” under Guided functions .

7.5

Torque settings, gearbox to engine

Jetta 2011 with 2.0 l - 85 kW engine ⇒ page 73 . Jetta 2011 with 2.5 l - 125 kW engine ⇒ page 74 .

72

Rep. Gr.37 - Controls, housing

rrectness of i t to the co nf o r m spec atio h re n in wit

cable support bracket and retainer for gate selector cable must be transferred.

thi sd o cu m en

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

with gearbox. Secure torque converter to prevent it from falling out.

ility ab y li an pt ce

♦

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d Note nte ise r o eo h t u ra a s s Pay attention to torque converter. It must be removed togetherc

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

7.5.1

Torque settings, Jetta 2011 with 2.0 l - 85 kW engine

- Drive plate to torque convert‐ er ❑ 60 Nm ❑ Qty. 6; remove and in‐ stall with insert -V/175- . - M12 bolts ⇒ M12 ❑ 80 Nm ❑ 65 Nm if you use socket -T10179- M10 bolts ⇒ M10 ❑ 40 Nm ❑ These bolts are located in lower flange - Two dowel sleeves in engine -arrows-

-Nuts- 8 Nm

rrectness of i t to the co nform spec at i h re o n wit in t his

– Make sure that bracket does not make contact with ATF cool‐ er.

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

ht rig py Co t.

7. Removing and installing gearbox, Jetta 2011 ▸

73

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

7.5.2

Torque settings, Jetta 2011 with 2.5 l - 125 kW engine

1 - Direction of travel - Drive plate to torque convert‐ er ❑ 60 Nm ❑ Qty. 6; remove and in‐ stall with insert -V/175- . - M12 bolts ⇒ M12 ❑ 80 Nm ❑ 65 Nm if you use socket -T10179- M10 bolts ⇒ M10 ❑ 40 Nm ❑ These bolts are located in lower flange

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

– Make sure that bracket does not make contact with ATF cool‐ er.

r fo ng

AG.

Rep. Gr.37 - Controls, housing

agen lksw Vo by

Prote cted by c o p yri gh t. C op yi

74

ht rig py Co t.

-Nuts- 8 Nm

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

- Two dowel sleeves in engine -arrows-

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

8

Transporting gearbox

Special tools and workshop equipment required ♦ Shackle -10 - 222 A /12-

Shackle 10-222 A/12 can be used to transport the automatic gearbox and set up gearbox support 3282.

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

ht rig py Co t.

r fo ng

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

– During transportation, protect torque converter -arrow- from falling out, e.g. with a wire -A-.

8. Transporting gearbox

75

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

9

ATF cooler

9.1

Assembly overview - ATF cooler

1 - Gearbox housing 2 - O-ring ❑ Always renew 3 - ATF cooler ❑ Installation position: ⇒ page 76 4 - O-ring ❑ Always renew 5 - Washer 6 - Dished washer

Position: ATF cooler ht rig py Co t.

– When installing ATF cooler -1-, insert lug -arrow B- into recess in gearbox housing. AG.

Rep. Gr.37 - Controls, housing

agen lksw Vo by

Prote cted by c o py rig ht . C op yi

76

do c um en

r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

tho au s s

Volkswagen AG does not gu ara nte eo ra c ility ab y li an pt ce

7 - Bolt ❑ 36 Nm

un le

AG. ❑ Position: convex side agen ksw l o V faces bolt by ed ⇒ Item 7 (page 76) ris

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

10

Checking ATF level and topping up

Please follow instructions: ♦ About this workshop manual ⇒ page 1 ♦ About ATF ⇒ page 2 ♦ About “filler pipe” ⇒ page 3 Special tools and workshop equipment required ♦ Torque wrench -V.A.G 1331♦ Used oil collection and ex‐ traction unit -V.A.G 1782♦ Vehicle diagnosis, testing and information system VAS 5051♦ Drip tray for workshop hoist -VAS 6208♦ Adapter for filling oil -VAS 6262-

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

ht rig py Co t.

r fo ng

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

♦ Adapter -VAS 6262/2-

10. Checking ATF level and topping up

77

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

tee or ac

r ho ut a ss

10.1

Checking ATF level

Carry out procedure as follows:

AG.

Prote cted by

•

Gearbox is not in emergency running mode and ATF temper‐ ature is not above approx. 30 °C.

•

Vehicle must be standing level

•

Selector lever in “P”.

– Connect “tester” and continue switching until it is ready for op‐ eration ⇒ page 11 . – Press Guided functions “on right”. – Then select vehicle, the gearbox and Check ATF level . – Press → . – Start engine. – Raise vehicle. – Place drip tray under gearbox. – Press → . If a test temperature between 35 °C and 45 °C is displayed:

78

Rep. Gr.37 - Controls, housing

agen lksw Vo by

c o p yri gh t. C op yi

The ATF temperature should not be more than approx. 30 °C at the start of the test.

ht rig py Co t.

r fo ng

– Switch off engine.

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

If ATF must be added, use only ATF listed in ⇒ Electronic parts catalogue ⇒ ETKA . . Volkswagen AG gen AG does swa inspection plug kATF not l o – If ATF level is checked, oil seal -arrow-yon V gu b ara d must always be renewed. n ise

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Remove inspection plug for ATF level from oil pan.

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

The ATF present in the overflow pipe runs out. If ATF drips out of drilling: ATF does not need topping up.

– Fit new seal to plug and tighten to 27 Nm. This concludes the ATF check. If no ATF drips out of inspection hole: – Top up ATF ⇒ page 79 .

Topping up ATF ht rig py Co t.

Carry out procedure as follows:

thi sd o cu m en

10.2

Prote cted by c o p yri gh t. C op yi

– With engine “running”, screw in adapter for filling oil -VAS 6262/2- hand-tight. agen lksw Vo by

AG.

– Add 1 l of ATF.

– Pull off adapter for oil filling -VAS 6262- at quick-release con‐ nection and check: If ATF now flows out of hole in adapter: ATF does not need topping up. – Drain ATF until it drips. – Fit new seal to plug and tighten to 27 Nm. This concludes the ATF check. If no ATF drips out: – Add another litre ⇒ page 79 . WARNING

An ATF level which is too low or too high will impair the function of the gearbox. But if the gearbox was 2 litres low, it must be carefully inspected. There is probably a “major” leak.

10. Checking ATF level and topping up

79

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

10.3

Draining and filling ATF

Carry out procedure as follows: – Switch off engine.

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

– Remove inspection plug for ATF level from oil pan -arrow-.

– Start engine, shift through all selector lever positions with ve‐ hicle stationary, leaving selector lever in each position for about 10 seconds. – Finally, check ATF level and top up ⇒ page 77 .

80

Rep. Gr.37 - Controls, housing

AG.

– Add 3 litres of ATF ⇒ Electronic parts catalogue ⇒ ETKA through filler pipe.

agen lksw Vo by

– Install plug hand-tight.

Prote cted by c o p yri gh t. C op yi

– Install overflow pipe.

ht rig py Co t.

– Drain ATF.

do c um en

– Remove overflow pipe -1- through inspection hole.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

38 –

Gears, control

1

Renewing oil seal for selector shaft

Special tools and workshop equipment required ♦ Thrust piece -T10174-

Carry out procedure as follows: – Remove multifunction switch -F125- ⇒ page 18 . – Carefully lever out selector shaft seal using a screwdriver. Do not damage selector shaft. – Drive in new seal to stop with thrust piece -T10174-. Do not cant oil seal in the process.

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

do c um en

ht rig py Co t.

r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

ility ab y li an pt ce

un le

– Adjust multifunction switch -F125- ⇒ page 20 .

1. Renewing oil seal for selector shaft

81

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ olkswagen AG 6-speed automatic gearbox 09G - Edition 04.2010 en AG. V

Removing and installing ATF pan

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

2.1

– Remove noise insulation below engine. – Place drip tray underneath. – Unscrew and remove ATF inspection plug -A-. – Remove overflow pipe -C- and allow remaining ATF to drain.

82

Rep. Gr.38 - Gears, control

Prote cted by

Removing

AG.

c o p yri gh t. C op yi

2.1.1

do c um en

♦ Torque wrench -V.A.G 1783-

agen lksw Vo by

♦ Drip tray for workshop hoist -VAS 6208-

rrectness of i t to the co nform spec at i h re o n wit in t his

Special tools and workshop equipment required

ht rig py Co t.

ATF pan

does not gu ara nte eo ra c ility ab y li an pt ce

2

ag ksw Vol y b ed ris o h t au ss

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Loosen oil pan bolts -arrows- diagonally. – Remove oil pan together with gasket.

Installing

Install in the reverse order of removal, observing the following: – Clean two magnets in recesses of oil pan. Make sure that magnets make full contact with oil pan. – Check that seal is undamaged and all spacer sleeves (qty. 8) are present. Otherwise renew seal. – Fit oil sump with seal, taking care not to pinch any wires. – Ensure proper seating of oil pan gasket. – Tighten pan bolts -arrows- diagonally in several stages; torque specification ⇒ page 89 .

rrectness of i t to the co nf o r m spec atio h re n in wit

2.1.2

thi sd o cu m en

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

2. ATF pan

83

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Screw in overflow pipe -C-; torque specification ⇒ page 89 . – Insert seal -B- for ATF inspection plug -A-. – Screw in ATF inspection plug -A- hand-tight with new seal -B-. – Fill with ATF; check ATF level and top up ⇒ page 77 .

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Rep. Gr.38 - Gears, control

do c um en

84

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

3

ATF strainer

3.1

Removing and installing ATF strainer

3.1.1

Removing

– Remove oil pan ⇒ page 82 . – Unscrew ATF strainer bolts -arrows-. – Pull ATF strainer -A- off valve body.

Installing

– Thinly coat seals on intake neck of ATF strainer with ATF. . Volkswagen AG gen AG a lksw

o – The ATF strainer must be renewed if seals are loose y V or de‐ db e s fective. i or h ut

– Install oil pan ⇒ page 82 .

r fo ng

– Fill with ATF; check ATF level and top up ⇒ page 77 .

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

un le

ility ab y li an pt ce

a – Place ATF strainer -A- onto valve body and ss tighten bolts -arrows-; torque specification ⇒ page 89 .

does not gu ara nte eo ra c

ht rig py Co t.

3.1.2

3. ATF strainer

85

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

un le

Valve body

pe rm itte d

4

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b 2005 ➤ , Jetta 2011 ➤ Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta ara d nte ise r o 6-speed automatic gearbox 09G - Edition 04.2010 eo h t u ra a c s s

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

Removing and installing valve body ⇒ page 91 Solenoid valve identification ⇒ page 90 Sender identification ⇒ page 91 . Torque settings ⇒ page 89 WARNING

Do not run engine or tow vehicle with pan removed or when there is no ATF in gearbox.

♦ Insert O-rings with ATF. Other lubricants lead to malfunction of the gearbox hydraulics.

Rep. Gr.38 - Gears, control

Prote cted by

86

AG.

♦ After the pan has been installed, the ATF level must be checked and topped up ⇒ page 77 .

agen lksw Vo by

c o p yri gh t. C op yi

♦ Do not use fluffy cloths.

ht rig py Co t.

♦ Always renew a valve body which is fouled or defective.

do c um en

r te o iva r rp fo g n

♦ The valve body and the wiring harnesses can also be removed when the gearbox is installed.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

4.1

Assembly overview

1 - ATF inspection plug ❑ Checking ATF level and topping up ⇒ page 77 AG. Volkswagen AG d agen oes ❑ Torque setting ksw not l o V gu y b ara ⇒ page 89 d e

nte eo ra c

is or

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

th 2 - Seal au s s ❑ Always renew

rrectness of i t to the co nform spec at i h re o n wit in t his

3 - Overflow pipe ❑ Unscrew to drain ATF ❑ Torque setting ⇒ page 89 4 - Oil pan ❑ Removing and installing ⇒ page 82 5 - Bolt ❑ Tighten oil pan bolts di‐ agonally in several stages. ❑ Torque setting ⇒ page 89

ht rig py Co t.

agen lksw Vo by

AG.

c o p yri gh t. C op yi

7 - Magnet ❑ Qty. 2 in depressions in pan ❑ Clean oil pan before in‐ stalling

do c um en

6 - Seal ❑ With spacer sleeves (qty. 8) ❑ Examine before fitting ❑ Renew brittle, cracked or deformed seal Prote cted by

8 - Bolt ❑ For securing valve body in gearbox ❑ Qty. 12, various lengths ⇒ page 95 ❑ Always renew bolts ❑ Torque setting ⇒ page 89 9 - Bolt ❑ Qty. 3 ❑ For securing strainer to valve body ❑ Torque setting ⇒ page 89 10 - ATF strainer ❑ Removing and installing ⇒ page 85 11 - Valve body ❑ Removing and installing ⇒ page 91 ❑ Solenoid valve identification ⇒ page 90 ❑ Allocation ⇒ Electronic parts catalogue “ETKA” 12 - Bolt ❑ Torque setting ⇒ page 89 4. Valve body

87

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 13 - Bolt ❑ Torque setting ⇒ page 89 14 - Gearbox input speed sender -G182❑ Removing and installing ⇒ page 106 15 - Bolt ❑ Torque setting ⇒ page 89 16 - Gearbox output speed sender -G195❑ Removing and installing ⇒ page 107 17 - Gearbox housing ❑ Shown here without ATF cooler 18 - Breather cap 19 - Multifunction switch -F125❑ Removing and installing ⇒ page 18 ❑ Adjusting ⇒ page 20 20 - Gearbox oil temperature sender -G93❑ Integrated into wiring harness ⇒ Item 23 (page 88) 21 - Bolt ❑ Torque setting ⇒ page 89 22 - Bolt ❑ Torque setting ⇒ page 89

25 - ATF drain plug ❑ Torque setting ⇒ page 89 26 - Selector lever ❑ For selector shaft ❑ Removing and installing ⇒ page 91 27 - Washer

28 - Nut ❑ Location: centring collar faces washer ⇒ Item 27 (page 88) ❑ Torque setting ⇒ page 89 29 - Spring ❑ Allocation ⇒ Electronic parts catalogue “ETKA” ht rig py Co t.

Prote cted by c o py rig ht . C op yi

30 - Damper piston

31 - Wiring harness with 14-pin connector ❑ For solenoid valves ❑ With O-ring on plug, always renew O-ring ❑ Solenoid valve locations and wiring harness routing ⇒ page 90 AG.

Rep. Gr.38 - Gears, control

agen lksw Vo by

88

rrectness of i t to the co nf o r m spec atio h re n in wit

24 - Seal ❑ Always renew

thi sd o cu m en

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

23 - Wiring harness with 8-pin connector ❑ With O-ring on plug, always renew O-ring . Volkswage ❑ With gearbox oil temperature asender gen AG -G93- n AG doe s no ksw l o t gu ❑ For gearbox input speed y V sender -G182ara db e nte s i r ❑ For gearbox output speed sender -G195o eo h ut ra a c ❑ Sender locations ⇒ page 91 s s ❑ Removing and installing ⇒ page 105 ❑ Allocation ⇒ Electronic parts catalogue “ETKA”

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ❑ Removing and installing ⇒ page 103 32 - Bolt ❑ Torque setting ⇒ page 89

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

r fo ng

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

Torque settings

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

4.1.1

4. Valve body

89

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

Solenoid valve identification

7 - Solenoid valve 9 -N2828 - Solenoid valve 10 -N2839 - Solenoid valve 3 -N90-

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

6 - Solenoid valve 5 -N92-

c o p yri gh t. C op yi

Rep. Gr.38 - Gears, control

thi sd o cu m en

90

rrectness of i t to the co nf o r m spec atio h re n in wit

5 - Solenoid valve 6 -N93-

Prote cted by

4 - Solenoid valve 4 -N91-

AG.

3 - Solenoid valve 2 -N89-

ility ab y li an pt ce

2 - Solenoid valve 1 -N88-

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

agen lksw Vo by

1 - Wiring harness for solenoid valves with 14-pin connector -arrow❑ Removing and installing ⇒ page 103

ht rig py Co t.

4.1.2

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed. Vautomatic olkswage gearbox 09G - Edition 04.2010

Sender identification

n AG d oes not gu ara nte eo ra c

2 - Connector to gearbox input speed sender -G1823 - Wire on gearbox input speed sender -G182-

agen lksw Vo by

AG.

Prote cted by

7 - Bracket of gearbox oil tem‐ perature sender -G93-

c o p yri gh t. C op yi

6 - Connector to gearbox out‐ put speed sender -G195-

ht rig py Co t.

5 - Wire on gearbox output speed sender -G195-

r fo ng

4 - Hydraulic pressure sender 2 for automatic gearbox G194❑ Not installed in all gear‐ boxes ❑ Allocation ⇒ Electronic parts catalogue “ETKA”

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

1 - Hydraulic pressure sender 1 for automatic gearbox G193❑ Not installed in all gear‐ boxes ❑ Allocation ⇒ Electronic parts catalogue “ETKA”

un le

4.1.3

AG agen ksw l o yV db ise r tho au s s

8 - Gearbox oil temperature sender -G939 - Wiring harness for sender with 8-pin connector -arrow❑ Removing and installing ⇒ page 105

4.2

Removing and installing valve body

Special tools and workshop equipment required ♦ Torque wrench -V.A.G 1331-

4. Valve body

91

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 ♦ Angle wrench -V.A.G 1756-

4.2.1

Removing

Carry out procedure as follows: – With ignition switched off, disconnect battery earth strap ⇒ Electrical system; Rep. Gr. 27 ; Battery; Disconnecting and connecting battery . – Remove oil pan ⇒ page 82 . – Remove ATF strainer ⇒ page 85 . – Draw a sketch of all senders and solenoid valves with their respective connectors analogous to figure. – Before separating connectors at senders and solenoid valves, solenoid valve or sender and respective connector must be n AG. Volkswagen AG do es n wage identified. o olks

un le

ility ab y li an pt ce

r fo ng

Under certain circumstances, interchanging connectors may lead to destruction of the gearbox.

AG.

Prote cted by

Rep. Gr.38 - Gears, control

agen lksw Vo by

c o p yri gh t. C op yi

92

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

This sketch and identification are absolutely vital to prevent in‐ advertently interchanging sender and solenoid valve when reinstalling valve body.

ht rig py Co t.

WARNING

t gu ara nte eo ra c

yV db ise r tho au s s

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

do c um en

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

– Use a small screwdriver to pry out securing bolts of connectors on solenoid valves -2- to -9- carefully and pull off connectors. – If a connector is damaged, the wiring harness or the valve body together with the solenoid valves must be renewed. – If present, carefully pull off connectors for automatic gearbox hydraulic pressure sender 1 -G193- -1- and automatic gearbox hydraulic pressure sender 2 -G194- -4-.

4. Valve body

93

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

rrectness of i t to the co nform spec at i h re o n wit in t his

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

Prote cted by c o py rig ht . C op yi

– If a connector is damaged, the wiring harness or the gearbox input speed sender -G182- or the gearbox output speed send‐ er -G195- must be renewed.

agen lksw Vo by

AG.

– Unscrew bolt -6-.

– For reinstallation, make sure bracket is attached to gearbox oil temperature sender -G93- -7-. – Carefully pull gearbox oil temperature sender -G93- -7- out of valve body together with bracket. – Unhook wiring harness from bracket -8-.

94

Rep. Gr.38 - Gears, control

ht rig py Co t.

– Unscrew bracket bolts -3-.

do c um en

– Separate connectors -2- and -5-.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Remove selector lever -1- from selector shaft. – In the process, carefully grip selector lever -1- with pliers -2so that torque is not transferred to multifunction switch -F125- . – Note spool valve -3- on valve body into which selector lever engages so that this is not damaged. Volkswa

gen AG does not gu ara nte eo ra c

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

ss

AG. agen ksw l o yV db ise r tho au

rrectness of i t to the co nform spec at i h re o n wit in t his

The spool valve is very “sensitive”. Even the slightest damage will lead to faults in operation. – Therefore, always push spool valve into valve body, secure against falling out and never interchange. The bolts are of different lengths and must be replaced.

Only the marked securing bolts -arrows- may be loosened.

AG.

-3- valve body designation, e.g. A2 in this case.

agen lksw Vo by

Prote cted by c o p yri gh t. C op yi

– Remove brackets -1- and -2-.

ht rig py Co t.

– Loosen securing bolts -arrows-, -arrows A- and -arrows B- for valve body diagonally and carefully remove valve body.

do c um en

If other bolts are loosened, the function of the valve body is im‐ peded or the valve body falls to pieces.

4. Valve body

95

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

Installing

Carry out procedure as follows: – Routing of wires must be noted precisely to prevent them from being trapped when valve body is positioned.

AG.

Prote cted by c o py rig ht . C op yi

– Route wiring harnesses -1-, -3-, -4- and -5- over edge of the gearbox according to figure. – Secure wiring harnesses on gearbox with adhesive tape. – Damper piston -2- must be installed in gearbox in illustrated position. – If damper piston -2- has been removed, it must be cleaned together with spring and installed in accordance with ⇒ Item 29 (page 88) and ⇒ Item 30 (page 88) . – Coat damper piston -2- and mounting in gearbox with ATF. – Insert spring in damper piston. – Insert damper piston with spring into mounting in gearbox.

– To prevent damper piston from falling out, press it into gearbox until valve body is positioned. – Carefully put on valve body, without pressing on forcefully.

96

Rep. Gr.38 - Gears, control

agen lksw Vo by

The distance -a- must be maintained to prevent wiring harness -5- from coming into contact with planetary gearbox and thereby becoming damaged during vehicle operation.

ht rig py Co t.

r fo ng

– Route wiring harness -5- in specified recess in gearbox ac‐ cording to figure.

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

4.2.2

AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s s

ility ab y li an pt ce

un le

– When removing valve body, secure damper piston -2- to pre‐ vent it from falling out or remove together with spring if nec‐ essary.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Wiring harnesses -1-, -3-, -4- and -5- are not allowed to be trapped by valve body.

– All bolts -arrows- for securing valve body must be inserted. – Note different bolt lengths: Bolts -arrowsBolts -arrows ABolts -arrows B-

M6×21 M6×16 M6×28

– Tighten brackets -1- and -2- for wiring harness hand-tight with new bolts.

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

r fo ng

ht rig py Co t.

– If lines -3-, -5- and -9- are too short to be connected to senders or bolted to intended points on valve body, they have been incorrectly routed or trapped by valve body. Remove valve body again and route cables correctly.

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

– Tighten remaining, new bolts for valve body -arrows-, -arrows A- and -arrows B- hand-tight.

4. Valve body

97

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Prote cted by

Rep. Gr.38 - Gears, control

AG.

98

agen lksw Vo by

c o p yri gh t . C op yi

– Tighten new bolts -arrows-, -arrows A- and -arrows B- from inside to outside to specified torque ⇒ page 89 .

ht rig py Co t.

Cables -3-, -5- and -9- are not allowed to be trapped.

do c um en

r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

es, in part or in w l purpos hole ercia , is n m ot com

pe rm itte d

un le

ility ab y li an pt ce

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ➤ Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ir se tee o h t or 6-speed automatic gearbox u 09G - Edition 04.2010 ac a ss

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu – Hook wiring harness -3- into retainer -7-by-arrow B-. ara d e nte is r o eo – Push selector lever -2- onto selector h shaft -6-. ut ra a c s s Ensure that selector lever pin -2- engages into spool valve -1-

-arrow A-. If necessary, position spool valve accordingly. – Set washer -5- and nut -4- on selector shaft -6-.

rrectness of i t to the co nform spec at i h re o n wit in t his

Centring collar of nut must face washer and run into washer on tightening. Wiring harness must be routed beneath selector lever.

– Tighten selector lever nut -1- to specified torque ⇒ page 89 . – In the process, carefully grip selector lever -1- with pliers -2so that torque is not transferred to multifunction switch -F125- . – Note spool valve -3- on valve body into which selector lever engages so that this is not damaged.

do c um en

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

– Connect the connectors to solenoid valves -2- to -9- according to the identifications which you have noted.

4. Valve body

99

ara nte e

pe rm itte d es, in part or in w l purpos hole ercia , is n m ot com r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s

agen lksw Vo by

AG.

Prote cted by c o py rig ht . C op yi

Under certain circumstances, interchanging connectors may lead to destruction of the gearbox. If a connector is damaged, the wiring harness or the valve body together with the solenoid valves must be renewed.

– Join connectors -2- and -5-.

100

Rep. Gr.38 - Gears, control

do c um en

WARNING

– Route wiring harness -1- as shown in figure.

or ac

ht rig py Co t.

ss

b ed ris o th au

ility ab y li an pt ce

un le

. Volkswage AG 2005 ➤ , Jetta 2011 ➤ Golf Variant 2007 ➤ , Golf Variant gen AG 2010 ➤ ,nJetta doe swa k l o 6-speed automatic gearbox 09G - Edition 04.2010 s not gu yV

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s s

thi sd o cu m en

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

The mating part of the connectors must bear the same identifica‐ tion as the respective connector itself. – Place the bracket onto the gearbox oil temperature sender G93- -7-. – Insert gearbox oil temperature sender -G93- in valve body to‐ gether with bracket. – Tighten bolt -6-, torque setting ⇒ page 89 . – If present, carefully push connectors onto automatic gearbox hydraulic pressure sender 1 -G193- -1- and automatic gearbox hydraulic pressure sender 2 -G194- -4- at right angles. – Tighten bolts -3- for connector retainers -2- and -5-; torque specifications ⇒ page 89 .

4. Valve body

101

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

– Install ATF strainer ⇒ page 85 . – Install oil pan ⇒ page 82 . – With ignition switched off, connect battery earth strap ⇒ Elec‐ trical system; Rep. Gr. 27 ; Battery; Disconnecting and con‐ necting battery . – Fill with ATF; check ATF level and top up ⇒ page 77 . – Connect -VAS 5051- and continue to advance until “Function/ component selection” is displayed. – Then press “Drive (Repair group 01; 10 ... 26; 28 ... 39)”. c o p yri gh t. C op yi

– Press “01 - Self-diagnosis”. Prote cted by

102

Rep. Gr.38 - Gears, control

AG.

– Press “Basic setting”.

agen lksw Vo by

– Press “Functions”.

ht rig py Co t.

– Then “6-speed automatic gearbox 09G”.

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

– Attach wiring harness to retainer -8- and route it as shown in figure.

rrectness of i t to the co nform spec at i h re o n wit in t his

– If cables are too short to be bolted on, they have been incor‐ rectly routed or trapped by the valve body. Remove valve body again and route cables correctly.

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

4.3

4.3.1

Removing and installing wiring harness with 14-pin connector (for solenoid valves) Removing

ility ab y li an pt ce

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

– Remove oil pan ⇒ page

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a 82ss. c

– Remove ATF strainer ⇒ page 85 .

– Draw a sketch of all senders and solenoid valves with their respective connectors analogous to figure.

rrectness of i t to the co nform spec at i h re o n wit in t his

– Before separating connectors at solenoid valves, solenoid valve and respective connector must be identified. WARNING

This sketch and identification are absolutely vital to prevent in‐ advertently interchanging sender and solenoid valve connector when reinstalling the wiring harness. Under certain circumstances, interchanging connectors may lead to destruction of the gearbox.

do c um en

4. Valve body

103

ht rig py Co t.

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

rrectness of i t to the co nf o r m spec atio h re n in wit

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

ility ab y li an pt ce

AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s s

c o p yri gh t. C op yi

AG.

Prote cted by

– Unscrew bolt for 14-pin gearbox connector.

agen lksw Vo by

– Pull connector -2- off gearbox connector.

– Pull connector and wiring harness outwards out of gearbox housing.

4.3.2

Installing

Install in the reverse order of removal, observing the following: – Renew O-ring on connector. – Push connector with new O-ring into gearbox to stop.

104

Rep. Gr.38 - Gears, control

ht rig py Co t.

– If a connector is damaged, the wiring harness or the valve body together with the solenoid valves must be renewed.

thi sd o cu m en

– Use a small screwdriver to pry out securing bolts of connectors on solenoid valves -2- to -9- carefully and pull off connectors.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Tighten bolt for 14-pin gearbox connector; torque specification ⇒ page 89 . – Tighten securing bolts for gearbox speed sender connector retainers; torque specifications ⇒ page 89 . – Tighten bolt on bracket of gearbox oil temperature sender G93- , torque setting ⇒ page 89 . – Install ATF strainer ⇒ page 85 . – Install oil pan ⇒ page 82 .

4.4

Removing and installing wiring harness with 8-pin connector (for sender)

4.4.1

Removing

– Remove oil pan ⇒ page 82 . – Remove ATF strainer ⇒ page 85 . – If present, carefully pull off connectors for automatic gearbox hydraulic pressure sender 1 -G193- -1- and automatic gearbox hydraulic pressure sender 2 -G194- -4-.

. Volkswagen AG gen AG does not gu ara nte eo ra c

pe rm itte d es, in part or in w l purpos hole ercia , is n m ot com r te o iva r rp fo g n

rrectness of i t to the co nform spec a t i h re o n in wit thi s do c um en

ht rig py Co t.

y db ise r tho au s s

ility ab y li an pt ce

un le

a Senders -1- and -4- are not installed inVoall lkswgearboxes.

4. Valve body

105

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t. C op yi

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Separate connectors -2- and -5-. – If a connector is damaged, the wiring harness or the gearbox input speed sender -G182- or the gearbox output speed send‐ er -G195- must be renewed. – Unscrew bolt -6-. – For reinstallation, make sure bracket is attached to gearbox oil temperature sender -G93- -7-. – Carefully pull gearbox oil temperature sender -G93- -7- out of valve body together with bracket. – Unhook wiring harness from bracket -8-. – Pull connector -1- off gearbox connector.

olkswagen AG en AG. V does not V gu y b ara d nte wiring harness ise outwards out of gearbox r o eo h t u ra a c s s

wag – Unscrew bolt for 8-pin gearbox connector. olks

ility ab y li an pt ce

rrectness of i t to the co nform spec at i h re o n wit in t his

4.4.2

Installing

Install in the reverse order of removal, observing the following: – Renew O-ring on connector. – Push connector with new O-ring into gearbox to stop. – Tighten bolt for 8-pin gearbox connector; torque specification ⇒ page 89 . – Tighten bolt on bracket of gearbox oil temperature sender G93- , torque setting ⇒ page 89 . – Install ATF strainer ⇒ page 85 . c o p yri gh t. C op yi

4.5

Removing and installing gearbox input speed sender -G182-

4.5.1

Removing

Prote cted by

Rep. Gr.38 - Gears, control

AG.

106

agen lksw Vo by

– Remove valve body ⇒ page 91 .

ht rig py Co t.

– Install oil pan ⇒ page 82 .

do c um en

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

– Pull connector and housing.

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ olkswagen AG n AG. V 6-speed automatic gearbox 09G - Edition 04.2010 doe wage – Unscrew bolt -1- from gearbox

-G182- .

ility ab y li an pt ce

rrectness of i t to the co nform spec at i h re o n wit in t his

Installing

Install in the reverse order of removal, observing the following: c o p yri gh t. C op yi

Prote cted by

4.6

Removing and installing gearbox output speed sender -G195-

4.6.1

Removing

AG.

– Install valve body ⇒ page 96 .

agen lksw Vo by

– Tighten bolt -1- for gearbox input speed sender -G182- ; torque specifications ⇒ page 89 .

ht rig py Co t.

– Press sender into gearbox to stop.

do c um en

4.5.2

s no t gu ara nte eo ra c

es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n

– Pull sender out of gearbox.

ks Vol by d e input speed sender ris tho u a ss

– Remove valve body ⇒ page 91 . – Unscrew bolt -2- from gearbox output speed sender -G195- . – Pull sender out of gearbox.

4.6.2

Installing

Install in the reverse order of removal, observing the following: – Press sender into gearbox to stop. 4. Valve body

107

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Tighten bolt -2- for gearbox output speed sender -G195- ; tor‐ que specifications ⇒ page 89 .

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

r fo ng

agen lksw Vo by

AG.

Prote cted by

c o p yri gh t . C op yi

Rep. Gr.38 - Gears, control

ht rig py Co t.

108

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

ility ab y li an pt ce

un le

– Install valve body ⇒ page 96 .

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010

39 –

Final drive - differential

1

Renewing oil seals for flange shafts

(Gearbox installed) Only the left-hand side is described here. Renewing oil seal on right-hand side is nearly identical. – On right, drive shaft remains installed in wheel bearing. Drive in seal with thrust piece -T10177- . – Left drive shaft must be removed. Drive in seal with thrust piece -T10176- .

Renewing oil seal for flange shaft

Special tools and workshop equipment required

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

rrectness of i t to the co nf o r m spec atio h re n in wit

agen lksw Vo by

AG.

Prote cted by

1. Renewing oil seals for flange shafts

thi sd o cu m en

c o p yri gh t . C op yi

♦ Puller -T10055-

ility ab y li an pt ce

♦ Drip tray for workshop hoist -VAS 6208-

ht rig py Co t.

1.1

n AG. Volkswagen AG do es n wage s k l ot g o yV ua b d ran ir se tee o h t or u ac a ss

109

AG. Volkswagen AG d agen oes ksw not l o V ua Golf Variant 2007 by ➤ , Golf Variant 2010 ➤ , Jetta g2005 d ran ➤ , Jetta e tee ris 6-speed automatic gearbox 09G Edition 04.2010 o h or ut ac a ss

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

1.1.1

ht rig py Co t.

r fo ng

♦ Thrust piece -T10177-

Removing flange shaft oil seal

Carry out procedure as follows: – Remove noise insulation tray. – Place drip tray underneath. – Mark position of -nuts- that are used for bolting suspension link onto wheel bearing housing. Relocate this position during assembly if at all possible. – Unscrew suspension link from wheel bearing housing.

– Press drive shaft out of gearbox. This procedure is described in ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and in‐ stalling drive shafts .

110

Rep. Gr.39 - Final drive - differential

rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en

urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p

un le

ility ab y li an pt ce

♦ Thrust piece -T10176-

2011 ➤

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 Right: – If present, remove heat shield above right drive shaft -arrows-.

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

rrectness of i t to the co nf o r m spec atio h re n in wit

Left:

ility ab y li an pt ce

–

AG. Volkswagen AG d agen oes ksw not l o V gu by ara d e nte is r o eo h ut ra a c s Raise right shaft as far as possibles and secure in this position.

– Depress brake pedal to remove bolt for left drive shaft -arrow- (second mechanic required).

agen lksw Vo by

AG.

Prote cted by c o p yri gh t. C op yi

– Remove left drive shaft ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

ht rig py Co t.

After this, do not set vehicle on the ground any more ⇒ Rep. Gr. 40 ; Repairing drive shafts; Removing and installing drive shafts .

thi sd o cu m en

Note

– Seal drive shaft aperture on transmission with a clean cloth -A-. – Carefully drill a hole -B- (size 2 to 4 mm) into outer sheet metal ring -C- of oil seal. Note ♦ Grease drill bit -B- so that metal chips adhere. ♦ Drill only through sheet metal ring -C- because gearbox may

otherwise be damaged.

1. Renewing oil seals for flange shafts

111

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤ 6-speed automatic gearbox 09G - Edition 04.2010 – Screw a self-tapping screw, approx. 4 mm in diameter, into hole drilled in oil seal -arrow-. Note

Do not screw in sheet metal screw too far to avoid damaging bearing behind it. – Pull out oil seal using puller -T10055- and adapter -T10055/2- . – Remove cloth and carefully clean gearbox and drive shaft aperture. No iron chips must enter gearbox or drive shaft aperture; vacuum up chips if necessary. If only the sheet metal ring of seal could be pulled out, carefully lever out rest of seal with a screwdriver.

1.1.2

Installing flange shaft oil seal

Install in the reverse order of removal, observing the following: – Apply ATF to circumference and sealing lips of oil Vseal. olkswa

Right side

rrectness of i t to the co nf o r m spec atio h re n in wit

– Drive seal -A- to stop with thrust piece -T10176- . Do not cant oil seal in the process.

– Drive seal -A- to stop with thrust piece -T10177- . Do not cant oil seal in the process. – Install drive shaft ⇒ Rep. Gr. 40 ; Repairing drive shafts; Re‐ moving and installing drive shafts .

AG.

Rep. Gr.39 - Final drive - differential

agen lksw Vo by

112

Prote cted by c o p yri gh t. C op yi

– Install noise insulation.

ht rig py Co t.

– Finally, check ATF level and top up ⇒ page 77 .

thi sd o cu m en

es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng

Left-hand side

gen AG does not gu ara nte eo ra c ility ab y li an pt ce

AG. agen ksw l o yV db ise r Open side of oil seal faces gearbox. tho au s – Press oil seal in straight ass far as possible by hand.

Installation position: