5480-2
Short Description
Descripción: Spline Details DIN 5480...
Description
DEUTSCHE NORM
May 2006
D
DIN 5480-2
ICS 21.120.10
Supersedes: see below
Involute splines based on reference diameters – Part 2: Nominal and inspection dimensions Passverzahnungen Passverzahnungen mit Evolventenflanken und Bezugsdurchmesser – Teil 2: Nennmaße und Prüfmaße
Supersedes DIN 5480-2:1991-10, DIN 5480-3:1991-10, DIN 5480-4:1991-10, DIN 5480-5:1991-10, DIN 5480-6:1991-10, DIN 5480-7:1991-10, DIN 5 480-8:1991-10, DIN 5480-9:1991-10, DIN 5480-10:1991-10, DIN 5480-11:1991-10, DIN 5480-12:1991-10, DIN 5480-13:1991-10 and DIN 5480 Corrigendum 1:1995-11.
Document comprises 40 pages
Translation by DIN-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text.
©
No part of this translation may be reproduced without prior permission of DIN Deutsches Institut für Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen).
English price group 14 www.din.de www.beuth.de
!,z2Z" 9871555
DIN 5480-2:2006-05
Contents
Page
Foreword............................................................................................................... Foreword................................ ..............................................................................................................................3 ...............................................3 1
Scope ....................................................................................... ..................................................................................................................................................... ...............................................................5 .5
2
Normative references.......................................................................................................................... references............................................................................................................................5 ..5
3 3.1 3.2 3.3
Graphic representation representation of dimensions and measurements..............................................................6 measurements..............................................................6 Space width/tooth thickness thickness .................................................................................... ................................................................................................................6 ............................6 Diameters................................................................................................................................................6 Inspection dimensions.................................................................................................. dimensions..........................................................................................................................6 ........................6
4
Module m = 0,5 mm ............................................................................... ................................................................................................................................8 .................................................8
5
Module m = 0,6 mm ............................................................................... ............................................................................................................................. .............................................. 10
6
Module m = 0,75 mm ....................................................................................... ........................................................................................................................... .................................... 12
7
Module m = 0,8 mm ............................................................................... ............................................................................................................................. .............................................. 14
8
Module m = 1 mm ............................................................................. ................................................................................................................................ ................................................... 16
9
Module m = 1,25 mm ....................................................................................... ........................................................................................................................... .................................... 18
10
Module m = 1,5 mm ............................................................................... ............................................................................................................................. .............................................. 20
11
Module m = 1,75 mm ....................................................................................... ........................................................................................................................... .................................... 22
12
Module m = 2 mm ............................................................................. ................................................................................................................................ ................................................... 24
13
Module m = 2,5 mm ............................................................................... ............................................................................................................................. .............................................. 26
14
Module m = 3 mm ............................................................................. ................................................................................................................................ ................................................... 28
15
Module m = 4 mm ............................................................................. ................................................................................................................................ ................................................... 30
16
Module m = 5 mm ............................................................................. ................................................................................................................................ ................................................... 32
17
Module m = 6 mm ............................................................................. ................................................................................................................................ ................................................... 34
18
Module m = 8 mm ............................................................................. ................................................................................................................................ ................................................... 36
19
Module m = 10 mm ................................................................................ .............................................................................................................................. .............................................. 38
Bibliography..................................................................................................................................................... Bibliography................................................................................................................... .................................. 40
Figures Figure 1 — Space width/tooth thickness.......................................................................................... thickness..........................................................................................................6 ................6 Figure 2 — Diameters.........................................................................................................................................6 Diameters........................................................................................................................................ .6 Figure 3 — Inspection Inspection dimensions ....................................................................................... ...................................................................................................................6 ............................6 Figure 4 — Tooth thickness measurement ........................................................................... ......................................................................................................7 ...........................7
See foreword for relationship to the ISO 4156 series of standards, including ISO 4156 AMD 1:1992, published by the International Organization for Standardization (ISO).
2
DIN 5480-2:2006-05
Contents
Page
Foreword............................................................................................................... Foreword................................ ..............................................................................................................................3 ...............................................3 1
Scope ....................................................................................... ..................................................................................................................................................... ...............................................................5 .5
2
Normative references.......................................................................................................................... references............................................................................................................................5 ..5
3 3.1 3.2 3.3
Graphic representation representation of dimensions and measurements..............................................................6 measurements..............................................................6 Space width/tooth thickness thickness .................................................................................... ................................................................................................................6 ............................6 Diameters................................................................................................................................................6 Inspection dimensions.................................................................................................. dimensions..........................................................................................................................6 ........................6
4
Module m = 0,5 mm ............................................................................... ................................................................................................................................8 .................................................8
5
Module m = 0,6 mm ............................................................................... ............................................................................................................................. .............................................. 10
6
Module m = 0,75 mm ....................................................................................... ........................................................................................................................... .................................... 12
7
Module m = 0,8 mm ............................................................................... ............................................................................................................................. .............................................. 14
8
Module m = 1 mm ............................................................................. ................................................................................................................................ ................................................... 16
9
Module m = 1,25 mm ....................................................................................... ........................................................................................................................... .................................... 18
10
Module m = 1,5 mm ............................................................................... ............................................................................................................................. .............................................. 20
11
Module m = 1,75 mm ....................................................................................... ........................................................................................................................... .................................... 22
12
Module m = 2 mm ............................................................................. ................................................................................................................................ ................................................... 24
13
Module m = 2,5 mm ............................................................................... ............................................................................................................................. .............................................. 26
14
Module m = 3 mm ............................................................................. ................................................................................................................................ ................................................... 28
15
Module m = 4 mm ............................................................................. ................................................................................................................................ ................................................... 30
16
Module m = 5 mm ............................................................................. ................................................................................................................................ ................................................... 32
17
Module m = 6 mm ............................................................................. ................................................................................................................................ ................................................... 34
18
Module m = 8 mm ............................................................................. ................................................................................................................................ ................................................... 36
19
Module m = 10 mm ................................................................................ .............................................................................................................................. .............................................. 38
Bibliography..................................................................................................................................................... Bibliography................................................................................................................... .................................. 40
Figures Figure 1 — Space width/tooth thickness.......................................................................................... thickness..........................................................................................................6 ................6 Figure 2 — Diameters.........................................................................................................................................6 Diameters........................................................................................................................................ .6 Figure 3 — Inspection Inspection dimensions ....................................................................................... ...................................................................................................................6 ............................6 Figure 4 — Tooth thickness measurement ........................................................................... ......................................................................................................7 ...........................7
See foreword for relationship to the ISO 4156 series of standards, including ISO 4156 AMD 1:1992, published by the International Organization for Standardization (ISO).
2
DIN 5480-2:2006-05
Validity This standard is valid from 2006-05-01.
Foreword This series of standards deals with involute splines and spline joints within a module range of 0,5 to 10, having a number of teeth ranging from 6 to 82 and with a pressure angle of 30°. The DIN 5480 series of standards is limited to splines with a pressure angle of 30°, since pressure angles of 37,5° and 45° are covered by ISO 4156. Involute splines in accordance with ISO 4156 are based on module series. These are not interchangeable with involute splines conforming to the DIN 5480 series of standards. The DIN 5480 series of standards is i s based on reference diameters that t hat are independent of the module, allowing an optimal fit to standard ball and roller bearing diameters and reducing the number of different tools required for manufacturing. man ufacturing. This series of standards has ha s been revised by Technical Committee Co mmittee 2.1 Passverzahnungen (“Involute splines”) of the Normenauschuss Maschinenbau Maschinenbau (Mechanical Engineering Standards Committee). The revision was considered necessary since a review of the DIN 5480 series of standards in accordance with DIN 820-4 had shown that the series had structural and editorial weaknesses. The object of the revision was to combine the individual parts of this standard in a practical, sensible manner. The entire series of standards now consists of only four parts instead of the previous sixteen. DIN 5480 Involute splines based on reference diameters now comprises:
⎯ Part 1: General ⎯ Part 2: Nominal and inspection dimensions ⎯ Part 15: Inspection ⎯ Part 16: Tools The new edition of DIN 5480-1 deals with fundamental principles, the same as its predecessor, but now also includes fit f it dimensions and tolerances, these being formerly f ormerly contained in i n DIN 5480-14:1986-03. The calculation formulae, tolerances and deviations contained in Part 1 also apply to the other parts of this series of standards. DIN 5480-2 now contains the nominal dimensions and inspection dimensions for the range of items stated above, and incorporates the contents of the former editions of DIN 5480-2 to DIN 5480-13. DIN 5480-15 covers quality inspections of spline joints. DIN 5480-16 defines the design features of tools for manufacturing involute splines.
3
DIN 5480-2:2006-05
Amendments This standard differs from DIN 5480-2:1991-10, DIN 5480-3:1991-10, DIN 5480-4:1991-10, DIN 5480-5:1991-10, DIN 5480-6:1991-10, 5480-6:1991-10, DIN 5480-7:1991-10, 5480-7:1991-10, DIN 5480-8:1991-10, 5480-8:1991-10, DIN 5480-9:1991-10, 5480-9:1991-10, DIN 5480-10:1991-10, 5480-10:1991-10, DIN 5480-11:1991-10, DIN 5480-12:1991-10, DIN 5480-13:1991-10 and DIN 5480 Corrigendum 1:1995-11 as follows: a)
The title has been changed to “Involute splines based on reference diameters”.
b)
The full root radius has been included for shafts.
c)
Cold-rolling Cold-rollin g has been included as a manufacturing process for shafts.
d)
The measuring circle (ball or pin) diameters have been taken from DIN 3977, with one exception.
e)
The standard has been editorially revised.
Previous editions DIN 5480-2: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-3: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-4: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-5: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-6: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-7: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-8: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-9: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-10: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-11: 1966-12; 1975-12; 1986-03; 1991-10 DIN 5480-12: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480-13: 1966-12; 1974-09; 1986-03; 1991-10 DIN 5480 Corrigendum 1: 1995-11
4
DIN 5480-2:2006-05
1
Scope
This standard applies to involute splines and spline joints based on reference diameters for connecting hubs and shafts either with a removable connection, a sliding fit or a permanent fit. It lays down the following general characteristics for splines as in this standard: a)
They have a standard pressure angle of 30°.
b)
The basic rack profile is the same for all pitches, therefore applying a uniform design rule to all profiles.
c)
They have a side fit profile (a diameter fit is permitted in some cases).
d)
Addendum modification is used in order to achieve specific reference diameters.
e)
The fit system includes tolerances for effective form deviations so that the effect of such deviations on backlash is taken into account. The specified range of fundamental deviations and tolerance classes takes due consideration of all requirements.
Involute spine joints as in this standard are used for connecting hubs and shafts either with a removable connection, a sliding fit or a permanent fit. They have all the characteristics required for centring the parts and transmitting torques, as well as meeting all the requirements for economical manufacturing. The theoretical root diameters for hubs and shafts where the dedendum of the basic rack profile, hfP, is 0,55 ⋅ m. The dedendum depends on the manufacturing method used, and can therefore have various values (see DIN 5480-1, Table 3). The root diameters depend on the dedendum.
2
Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 5480-1, Involute splines based on reference diameters – Part 1: General DIN 5480-15, Involute splines based on reference diameters – Part 15: Inspection DIN 5480-16, Involute splines based on reference diameters – Part 16: Tools
5
DIN 5480-2:2006-05
3 3.1
Graphic representation of dimensions and measurements Space width/tooth thickness
Figure 1 — Space width/tooth thickness
3.2
Diameters
Key 1 2
Shaft Hub Figure 2 — Diameters
3.3
Inspection dimensions
Key 1 2
Shaft Hub Dimension M 2 between 2 measuring circles (balls or pins)
Dimension M 1 over 2 measuring circles (balls or pins)
Figure 3 — Inspection dimensions
6
DIN 5480-2:2006-05
Key a) Unfavourable position near the tip b) Favourable position near the V circle c) Unfavourable position near the root form circle Figure 4 — Tooth thickness measurement Table 1 — Root fillet radii and deviation factors Dimensions in mm
m
Minimum root fillet radius for chipremoval manufacturing methods
Nominal value for cold-rolling
mm
ρ F min
ρ F
0,5
0,08
0,27
0,866
0,6
0,10
0,32
0,866
0,75
0,12
0,40
0,866
0,8
0,13
0,43
0,866
1
0,16
0,54
0,866
1,25
0,20
0,67
0,866
1,5
0,24
0,81
0,866
1,75
0,28
0,94
0,866
2
0,32
1,08
0,866
2,5
0,40
1,35
0,866
3
0,48
1,62
0,866
4
0,64
2,16
0,866
5
0,80
–
0,866
6
0,96
–
0,866
8
1,28
–
0,866
10
1,60
–
0,866
Module
Deviation factor A *Wk
7
DIN 5480-2:2006-05
4
Module m = 0,5 mm Table 2 — Nominal dimensions,
m =
0,5 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumber Pitch ence of teeth diameter diameter
a
8
Base diameter
Hub diameters
Shaft Space width Root addendum Tooth diammodification thickness eter
Deviationa
Root form circle diameter
Shaft diameters Tip diameter
Tip diameter
d Ff2
Root form circle Root a diameter diameter Deviation d Ff1
⋅m
e2 = s1
d f2
Adf2
min.
d a2
d a1
max.
4,330
0,225
1,045
6
0,19
5,95
5
5,9
6
5,196
0,225
1,045
7
0,19
6,95
6
14
7
6,062
0,225
1,045
8
0,19
7,95
9
16
8
6,928
0,225
1,045
9
0,19
10
18
9
7,794
0,225
1,045
10
11
20
10
8,660
0,225
1,045
12
22
11
9,526
0,225
13
24
12
10,392
14
26
13
15
28
16
d B
z
d
d b
6
10
5
7
12
8
x1
d f1
Adf1
4,95
4,90
–0,41
6,9
5,95
5,90
–0,41
7
7,9
6,95
6,90
–0,41
8,95
8
8,9
7,95
7,90
–0,41
0,19
9,95
9
9,9
8,95
8,90
–0,41
11
0,19
10,95
10
10,9
9,95
9,90
–0,41
1,045
12
0,19
11,95
11
11,9
10,95
10,90
–0,41
0,225
1,045
13
0,20
12,96
12
12,9
11,94
11,90
–0,45
11,258
0,225
1,045
14
0,20
13,96
13
13,9
12,94
12,90
–0,45
14
12,124
0,225
1,045
15
0,20
14,96
14
14,9
13,94
13,90
–0,45
30
15
12,990
0,225
1,045
16
0,20
15,96
15
15,9
14,94
14,90
–0,45
17
32
16
13,856
0,225
1,045
17
0,20
16,96
16
16,9
15,94
15,90
–0,45
18
34
17
14,722
0,225
1,045
18
0,20
17,96
17
17,9
16,94
16,90
–0,45
19
36
18
15,588
0,225
1,045
19
0,20
18,96
18
18,9
17,94
17,90
–0,45
20
38
19
16,454
0,225
1,045
20
0,20
19,96
19
19,9
18,94
18,90
–0,45
21
40
20
17,321
0,225
1,045
21
0,20
20,96
20
20,9
19,94
19,90
–0,45
22
42
21
18,187
0,225
1,045
22
0,20
21,96
21
21,9
20,94
20,90
–0,45
23
44
22
19,053
0,225
1,045
23
0,20
22,96
22
22,9
21,94
21,90
–0,45
24
46
23
19,919
0,225
1,045
24
0,20
23,96
23
23,9
22,94
22,90
–0,45
25
48
24
20,785
0,225
1,045
25
0,20
24,96
24
24,9
23,94
23,90
–0,45
26
50
25
21,651
0,225
1,045
26
0,21
25,96
25
25,9
24,94
24,90
–0,49
27
52
26
22,517
0,225
1,045
27
0,21
26,96
26
26,9
25,94
25,90
–0,49
28
54
27
23,383
0,225
1,045
28
0,21
27,96
27
27,9
26,94
26,90
–0,49
29
56
28
24,249
0,225
1,045
29
0,21
28,96
28
28,9
27,94
27,90
–0,49
30
58
29
25,115
0,225
1,045
30
0,21
29,96
29
29,9
28,94
28,90
–0,49
31
60
30
25,981
0,225
1,045
31
0,21
30,96
30
30,9
29,94
29,90
–0,49
32
62
31
26,847
0,225
1,045
32
0,21
31,96
31
31,9
30,94
30,90
–0,49
33
64
32
27,713
0,225
1,045
33
0,21
32,96
32
32,9
31,94
31,90
–0,49
34
66
33
28,579
0,225
1,045
34
0,21
33,96
33
33,9
32,94
32,90
–0,49
35
68
34
29,445
0,225
1,045
35
0,21
34,96
34
34,9
33,94
33,90
–0,49
36
70
35
30,311
0,225
1,045
36
0,21
35,96
35
35,9
34,94
34,90
–0,49
37
72
36
31,177
0,225
1,045
37
0,21
36,96
36
36,9
35,94
35,90
–0,49
38
74
37
32,043
0,225
1,045
38
0,21
37,96
37
37,9
36,94
36,90
–0,49
39
76
38
32,909
0,225
1,045
39
0,21
38,96
38
38,9
37,94
37,90
–0,49
40
78
39
33,775
0,225
1,045
40
0,21
39,96
39
39,9
38,94
38,90
–0,49
The deviation values given here relate to chip-cutting machining methods and the theoretical root diameter (see DIN 5480-1, 7.1). The deviation for cold-rolled splines is –0,76 ⋅ m.
DIN 5480-2:2006-05
Table 3 — Inspection dimensions,
m =
0,5 mm Dimensions in mm
Basic data Reference diameter
a
Hub dimensions
Number Measuring of teeth circle diameter
Shaft dimensions
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension W k
d B
z
DM
M 2
A *M2
DM
M 1
A *M1
k
6
10
1,0
3,797
2,01
1,25
7,511
1,20
3a
3,859
7
12
1,0
4,800
1,95
1,25
8,540
1,23
3
3,905 3,952
8
14
1,0
5,801
1,91
1,25
9,564
1,27
3a
9
16
1,0
6,803
1,88
1,25
10,584
1,29
4a
5,359
10
18
1,0
7,804
1,86
1,0
10,961
1,39
4
5,405
11
20
1,0
8,804
1,85
1,0
11,970
1,41
4a
5,452
12
22
1,0
9,805
1,84
1,0
12,978
1,43
5
6,859
13
24
1,0
10,805
1,83
1,0
13,985
1,44
5
6,905
14
26
1,0
11,806
1,82
1,0
14,991
1,46
5a
6,952
15
28
1,0
12,806
1,81
1,0
15,996
1,47
6
8,359
16
30
1,0
13,807
1,80
1,0
17,001
1,48
6
8,405
17
32
1,0
14,807
1,80
1,0
18,005
1,49
6a
8,452
18
34
1,0
15,807
1,80
1,0
19,009
1,50
7
9,859
19
36
1,0
16,807
1,79
1,0
20,013
1,51
7
9,905
20
38
1,0
17,807
1,79
1,0
21,016
1,52
7a
9,952
21
40
1,0
18,808
1,79
1,0
22,019
1,53
8
11,359
22
42
1,0
19,808
1,78
1,0
23,022
1,54
8
11,405
23
44
1,0
20,808
1,78
1,0
24,024
1,54
8a
11,452
24
46
1,0
21,808
1,78
1,0
25,026
1,55
9
12,859
25
48
1,0
22,808
1,78
1,0
26,029
1,55
9
12,905
26
50
1,0
23,808
1,77
1,0
27,031
1,56
9a
12,952
27
52
1,0
24,808
1,77
1,0
28,033
1,57
10
14,359
28
54
1,0
25,808
1,77
1,0
29,034
1,57
10
14,405
29
56
1,0
26,808
1,77
1,0
30,036
1,57
10 a
14,452
30
58
1,0
27,808
1,77
1,0
31,038
1,58
11
15,859
31
60
1,0
28,808
1,77
1,0
32,039
1,58
11
15,905
32
62
1,0
29,809
1,77
1,0
33,040
1,59
11 a
15,952
33
64
1,0
30,809
1,76
1,0
34,042
1,59
12
17,359
34
66
1,0
31,809
1,76
1,0
35,043
1,59
12
17,405
35
68
1,0
32,809
1,76
1,0
36,044
1,60
12 a
17,452
36
70
1,0
33,809
1,76
1,0
37,045
1,60
13
18,859
37
72
1,0
34,809
1,76
1,0
38,046
1,60
13
18,905
38
74
1,0
35,809
1,76
1,0
39,048
1,61
13 a
18,952
39
76
1,0
36,809
1,76
1,0
40,048
1,61
14
20,359
40
78
1,0
37,809
1,76
1,0
41,049
1,61
14
20,405
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
9
DIN 5480-2:2006-05
5
Module m = 0,6 mm Table 4 — Nominal dimensions,
m =
0,6 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch Base diameter diameter
Shaft Space width addendum Tooth modification thickness
Hub diameter Root diameter
Deviation
Shaft diameter
Root form Tip circle diameter diameter d Ff2
Tip diameter
⋅m
e2 = s1
d f2
Adf2
min.
d a2
d a1
4,157
0,27
1,254
6
0,21
5,93
4,8
5,88
6,0
5,196
0,17
1,139
7
0,21
6,93
5,8
12
7,2
6,235
0,07
1,023
8
0,21
7,93
9
13
7,8
6,755
0,27
1,254
9
0,21
10
15
9,0
7,794
0,17
1,139
10
11
17
10,2
8,833
0,07
1,023
12
18
10,8
9,353
0,27
13
20
12,0
10,392
14
22
13,2
15
23
16
z
d
d b
6
8
4,8
7
10
8
x1
max.
Deviation
d f1
Adf1
4,75
4,68
–0,43
6,88
5,75
5,68
–0,43
6,8
7,88
6,75
6,68
–0,43
8,93
7,8
8,88
7,75
7,68
–0,43
0,21
9,93
8,8
9,88
8,75
8,68
–0,43
11
0,21
10,93
9,8
10,88
9,75
9,68
–0,43
1,254
12
0,21
11,93
10,8
11,88
10,75
10,68
–0,43
0,17
1,139
13
0,22
12,94
11,8
12,88
11,74
11,68
–0,47
11,432
0,07
1,023
14
0,22
13,94
12,8
13,88
12,74
12,68
–0,47
13,8
11,951
0,27
1,254
15
0,22
14,94
13,8
14,88
13,74
13,68
–0,47
25
15,0
12,990
0,17
1,139
16
0,22
15,94
14,8
15,88
14,74
14,68
–0,47
17
27
16,2
14,030
0,07
1,023
17
0,22
16,94
15,8
16,88
15,74
15,68
–0,47
18
28
16,8
14,549
0,27
1,254
18
0,22
17,94
16,8
17,88
16,74
16,68
–0,47
19
30
18,0
15,588
0,17
1,139
19
0,22
18,94
17,8
18,88
17,74
17,68
–0,47
20
32
19,2
16,628
0,07
1,023
20
0,22
19,94
18,8
19,88
18,74
18,68
–0,47
21
34
20,4
17,667
–0,03
0,908
21
0,22
20,94
19,8
20,88
19,74
19,68
–0,47
22
35
21,0
18,187
0,17
1,139
22
0,22
21,94
20,8
21,88
20,74
20,68
–0,47
23
37
22,2
19,226
0,07
1,023
23
0,22
22,94
21,8
22,88
21,74
21,68
–0,47
24
38
22,8
19,745
0,27
1,254
24
0,22
23,94
22,8
23,88
22,74
22,68
–0,47
25
40
24,0
20,785
0,17
1,139
25
0,22
24,94
23,8
24,88
23,74
23,68
–0,47
26
42
25,2
21,824
0,07
1,023
26
0,23
25,94
24,8
25,88
24,74
24,68
–0,51
27
44
26,4
22,863
–0,03
0,908
27
0,23
26,94
25,8
26,88
25,74
25,68
–0,51
28
45
27,0
23,383
0,17
1,139
28
0,23
27,94
26,8
27,88
26,74
26,68
–0,51
29
47
28,2
24,422
0,07
1,023
29
0,23
28,94
27,8
28,88
27,74
27,68
–0,51
30
48
28,8
24,942
0,27
1,254
30
0,23
29,94
28,8
29,88
28,74
28,68
–0,51
31
50
30,0
25,981
0,17
1,139
31
0,23
30,94
29,8
30,88
29,74
29,68
–0,51
32
52
31,2
27,020
0,07
1,023
32
0,23
31,94
30,8
31,88
30,74
30,68
–0,51
33
54
32,4
28,059
–0,03
0,908
33
0,23
32,94
31,8
32,88
31,74
31,68
–0,51
34
55
33,0
28,579
0,17
1,139
34
0,23
33,94
32,8
33,88
32,74
32,68
–0,51
35
57
34,2
29,618
0,07
1,023
35
0,23
34,94
33,8
34,88
33,74
33,68
–0,51
36
58
34,8
30,138
0,27
1,254
36
0,23
35,94
34,8
35,88
34,74
34,68
–0,51
37
60
36,0
31,177
0,17
1,139
37
0,23
36,94
35,8
36,88
35,74
35,68
–0,51
38
62
37,2
32,216
0,07
1,023
38
0,23
37,94
36,8
37,88
36,74
36,68
–0,51
39
64
38,4
33,255
–0,03
0,908
39
0,23
38,94
37,8
38,88
37,74
37,68
–0,51
40
64
38,4
33,255
0,47
1,485
40
0,23
39,94
38,8
39,88
38,74
38,68
–0,51
42
68
40,8
35,334
0,27
1,254
42
0,23
41,94
40,8
41,88
40,74
40,68
–0,51
45
74
44,4
38,452
–0,03
0,908
45
0,23
44,94
43,8
44,88
43,74
43,68
–0,51
47
76
45,6
39,491
0,37
1,370
47
0,23
46,94
45,8
46,88
45,74
45,68
–0,51
48
78
46,8
40,530
0,27
1,254
48
0,23
47,94
46,8
47,88
46,74
46,68
–0,51
10
d B
Root form circle Root diameter diameter d Ff1
DIN 5480-2:2006-05
Table 5 — Inspection dimensions,
m =
0,6 mm Dimensions in mm
Basic data
Hub dimensions
Reference Number of Measuring diameter teeth circle diameter
a
Shaft dimensions
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension W k
d B
z
DM
M 2
A *M2
DM
M 1
A *M1
k
6
8
1,0
3,964
1,58
1,75
8,348
1,12
2a
2,942
7
10
1,0
4,972
1,76
1,5
8,874
1,22
2a
2,898
8
12
1,0
5,959
1,95
1,25
9,327
1,36
3
4,486
9
13
1,0
6,909
1,62
1,5
10,795
1,24
3
4,714
10
15
1,0
7,923
1,74
1,25
11,250
1,36
3a
4,670
11
17
1,0
8,921
1,86
1,25
12,307
1,42
4a
6,258
12
18
1,0
9,969
1,66
1,5
13,922
1,32
4
6,486
13
20
1,0
10,972
1,74
1,25
14,333
1,43
4
6,442
14
22
1,0
11,966
1,84
1,25
15,372
1,47
4
6,398
15
23
1,0
12,937
1,67
1,25
16,275
1,42
5
8,258
16
25
1,0
13,943
1,74
1,25
17,319
1,46
5
8,214
17
27
1,0
14,940
1,81
1,25
18,356
1,51
5
8,170
18
28
1,0
15,970
1,68
1,25
19,330
1,46
6
10,030
19
30
1,0
16,972
1,74
1,25
20,365
1,50
6
9,986
20
32
1,0
17,968
1,80
1,25
21,394
1,53
6
9,942
21
34
1,0
18,957
1,86
1,25
22,417
1,57
6
9,898
22
35
1,0
19,951
1,74
1,25
23,353
1,52
7
11,758
23
37
1,0
20,949
1,79
1,25
24,380
1,55
7
11,714
24
38
1,0
21,971
1,69
1,25
25,356
1,51
7a
11,942
25
40
1,0
22,972
1,74
1,25
26,384
1,54
7a
11,898
26
42
1,0
23,969
1,78
1,25
27,407
1,57
8
13,486
27
44
1,0
24,961
1,83
1,25
28,425
1,60
8
13,442
28
45
1,0
25,956
1,74
1,25
29,374
1,56
8a
13,670
29
47
1,0
26,954
1,78
1,25
30,395
1,58
9a
15,258
30
48
1,0
27,971
1,70
1,25
31,374
1,54
9
15,486
31
50
1,0
28,972
1,74
1,25
32,396
1,57
9
15,442
32
52
1,0
29,970
1,77
1,25
33,415
1,60
9a
15,398
9a
15,354
33
54
1,0
30,963
1,81
1,25
34,431
1,62
34
55
1,0
31,959
1,74
1,25
35,387
1,58
10
17,214
35
57
1,0
32,957
1,77
1,25
36,405
1,61
10
17,170
36
58
1,0
33,971
1,71
1,25
37,386
1,57
11
19,030
37
60
1,0
34,972
1,74
1,25
38,405
1,59
11
18,986
38
62
1,0
35,970
1,77
1,25
39,421
1,61
11
18,942
39
64
1,0
36,965
1,80
1,25
40,434
1,64
11
18,898
40
64
1,0
37,960
1,66
1,25
41,353
1,55
12
21,030
42
68
1,0
39,971
1,71
1,25
43,395
1,59
12 a
20,942
45
74
1,0
42,966
1,79
1,25
46,437
1,65
13
22,442
47
76
1,0
44,968
1,69
1,25
48,385
1,59
14
24,530
48
78
1,0
45,971
1,71
1,25
49,402
1,60
14
24,486
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
11
DIN 5480-2:2006-05
6
Module m = 0,75 mm Table 6 — Nominal dimensions,
m =
0,75 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
Base diameter
d B
z
d
d b
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55
6 8 9 10 12 13 14 16 17 18 20 21 22 24 25 26 28 29 30 32 33 34 36 37 38 40 41 42 44 45 46 48 49 50 52 54 58 60 62 64 68 72
4,50 6,00 6,75 7,50 9,00 9,75 10,50 12,00 12,75 13,50 15,00 15,75 16,50 18,00 18,75 19,50 21,00 21,75 22,50 24,00 24,75 25,50 27,00 27,75 28,50 30,00 30,75 31,50 33,00 33,75 34,50 36,00 36,75 37,50 39,00 40,50 43,50 45,00 46,50 48,00 51,00 54,00
3,897 5,196 5,846 6,495 7,794 8,444 9,093 10,392 11,042 11,691 12,990 13,640 14,289 15,588 16,238 16,887 18,187 18,836 19,486 20,785 21,434 22,084 23,383 24,032 24,682 25,981 26,630 27,280 28,579 29,228 29,878 31,177 31,826 32,476 33,775 35,074 37,672 38,971 40,270 41,569 44,167 46,765
12
Shaft addendum modification x1
⋅m
0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,2125 0,3375 0,0875 0,3375 0,3375 0,5875 0,3375 0,5875 0,0875 0,0875
Hub diameter Root form circle Deviation diameter d Ff2
Space width Tooth thickness
Root diameter
e2 = s1
d f2
Adf2
1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,423 1,568 1,279 1,568 1,568 1,856 1,568 1,856 1,279 1,279
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55
0,24 0,24 0,24 0,24 0,24 0,24 0,24 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,27 0,27
Shaft diameter Tip diameter
Tip diameter
Root form circle diameter d Ff1
Root diameter
Deviation
min.
d a2
d a1
max.
d f1
Adf1
5,90 6,90 7,90 8,90 9,90 10,90 11,90 12,91 13,91 14,91 15,91 16,91 17,91 18,91 19,91 20,91 21,91 22,91 23,91 24,91 25,91 26,91 27,91 28,91 29,91 30,91 31,91 32,91 33,91 34,91 35,91 36,91 37,91 38,91 39,91 41,91 44,91 46,91 47,91 49,91 51,92 54,92
4,5 5,5 6,5 7,5 8,5 9,5 10,5 11,5 12,5 13,5 14,5 15,5 16,5 17,5 18,5 19,5 20,5 21,5 22,5 23,5 24,5 25,5 26,5 27,5 28,5 29,5 30,5 31,5 32,5 33,5 34,5 35,5 36,5 37,5 38,5 40,5 43,5 45,5 46,5 48,5 50,5 53,5
5,85 6,85 7,85 8,85 9,85 10,85 11,85 12,85 13,85 14,85 15,85 16,85 17,85 18,85 19,85 20,85 21,85 22,85 23,85 24,85 25,85 26,85 27,85 28,85 29,85 30,85 31,85 32,85 33,85 34,85 35,85 36,85 37,85 38,85 39,85 41,85 44,85 46,85 47,85 49,85 51,85 54,85
4,45 5,45 6,45 7,45 8,45 9,45 10,45 11,44 12,44 13,44 14,44 15,44 16,44 17,44 18,44 19,44 20,44 21,44 22,44 23,44 24,44 25,44 26,44 27,44 28,44 29,44 30,44 31,44 32,44 33,44 34,44 35,44 36,44 37,44 38,44 40,44 43,44 45,44 46,44 48,44 50,43 53,43
4,35 5,35 6,35 7,35 8,35 9,35 10,35 11,35 12,35 13,35 14,35 15,35 16,35 17,35 18,35 19,35 20,35 21,35 22,35 23,35 24,35 25,35 26,35 27,35 28,35 29,35 30,35 31,35 32,35 33,35 34,35 35,35 36,35 37,35 38,35 40,35 43,35 45,35 46,35 48,35 50,35 53,35
–0,46 –0,46 –0,46 –0,46 –0,46 –0,46 –0,46 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,50 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,54 –0,58 –0,58
DIN 5480-2:2006-05
Table 7 — Inspection dimensions,
m =
0,75 mm Dimensions in mm
Basic data
Hub dimensions
Reference Number of Measuring diameter teeth circle diameter
a
Shaft dimensions
Nominal dimension
Deviation factor
Measuring Nominal circle diameter dimension
Deviation factor
Number of teeth measured
Nominal dimension
d B
z
DM
M 2
A *M2
DM
M 1
A *M1
k
W k
6 7
6 8
1,5 1,25
2,673 4,438
2,42 2,13
2,75 1,75
10,087 9,072
1,02 1,23
2 2
3,608 3,428
8 9
9 10
1,25 1,5
5,363 5,695
1,73 2,01
1,75 2,0
9,894 11,564
1,21 1,18
2a 3a
3,588 5,788
10 11 12
12 13 14
1,25 1,25 1,5
7,449 8,395 8,702
1,95 1,74 1,91
1,5 1,5 1,75
11,497 12,374 14,037
1,38 1,35 1,29
3 3 3a
5,608 5,768 5,928
13 14
16 17
1,25 1,25
10,454 11,411
1,88 1,74
1,5 1,5
14,522 15,424
1,44 1,41
3 4
5,747 7,948
15 16 17 18
18 20 21 22
1,25 1,25 1,25 1,5
12,461 13,457 14,421 14,707
1,66 1,85 1,74 1,84
1,5 1,5 1,5 1,5
16,442 17,539 18,457 19,467
1,39 1,48 1,45 1,43
4 4 4a 5
8,108 7,928 8,088 10,288
19 20
24 25
1,25 1,25
16,458 17,428
1,83 1,74
1,5 1,5
20,552 21,481
1,51 1,48
5 5
10,108 10,268
21 22 23
26 28 29
1,50 1,25 1,25
17,709 19,459 20,434
1,82 1,81 1,74
1,5 1,5 1,5
22,486 23,561 24,499
1,46 1,53 1,50
5a 5a 6
10,428 10,247 12,448
24 25 26
30 32 33
1,25 1,25 1,25
21,463 22,460 23,437
1,69 1,80 1,74
1,5 1,5 1,5
25,501 26,569 27,513
1,48 1,55 1,52
6 6 6a
12,608 12,428 12,588
27 28 29
34 36 37
1,25 1,25 1,25
24,463 25,461 26,440
1,69 1,79 1,74
1,5 1,5 1,5
28,514 29,575 30,524
1,50 1,56 1,54
7 7 7
14,788 14,608 14,768
30 31 32
38 40 41
1,25 1,25 1,25
27,463 28,461 29,443
1,69 1,79 1,74
1,5 1,5 1,5
31,524 32,580 33,534
1,52 1,58 1,55
7a 7a 8
14,928 14,747 16,948
33 34
42 44
1,25 1,25
30,463 31,462
1,70 1,78
1,5 1,5
34,532 35,584
1,54 1,59
8 8
17,108 16,928
35 36 37
45 46 48
1,25 1,25 1,25
32,445 33,464 34,462
1,74 1,70 1,78
1,5 1,5 1,5
36,542 37,540 38,588
1,57 1,55 1,60
8a 9 9
17,088 19,288 19,108
38 39
49 50
1,25 1,25
35,447 36,464
1,74 1,70
1,5 1,5
39,549 40,546
1,58 1,56
9 9a
19,268 19,428
40 42 45 47
52 54 58 60
1,25 1,25 1,25 1,25
37,462 39,464 42,464 44,450
1,77 1,71 1,71 1,66
1,5 1,5 1,5 1,5
41,591 43,552 46,556 48,510
1,61 1,57 1,58 1,55
9a 10 11 11 a
19,247 21,608 23,788 24,108
48 50
62 64
1,25 1,25
45,464 47,451
1,71 1,66
1,5 1,5
49,561 51,517
1,59 1,56
11 a 12
23,928 26,288
52 55
68 72
1,25 1,25
49,463 52,463
1,76 1,76
1,5 1,5
53,600 56,602
1,63 1,64
12 13
25,928 28,108
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
13
DIN 5480-2:2006-05
7
Module m = 0,8 mm Table 8 — Nominal dimensions,
m =
0,8 mm Dimensions in mm
Nominal dimensions
Basic data Reference diameter
Number of teeth
Pitch diameter
Base diameter
d B
z
d
d b
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60
6 7 8 10 11 12 13 15 16 17 18 20 21 22 23 24 25 26 27 28 30 31 32 34 35 36 37 38 40 41 42 44 45 46 47 48 51 55 57 58 60 64 66 70 74
4,8 5,6 6,4 8,0 8,8 9,6 10,4 12,0 12,8 13,6 14,4 16,0 16,8 17,6 18,4 19,2 20,0 20,8 21,6 22,4 24,0 24,8 25,6 27,2 28,0 28,8 29,6 30,4 32,0 32,8 33,6 35,2 36,0 36,8 37,6 38,4 40,8 44,0 45,6 46,4 48,0 51,2 52,8 56,0 59,2
4,157 4,850 5,543 6,928 7,621 8,314 9,007 10,392 11,085 11,778 12,471 13,856 14,549 15,242 15,935 16,628 17,321 18,013 18,706 19,399 20,785 21,477 22,170 23,556 24,249 24,942 25,634 26,327 27,713 28,406 29,098 30,484 31,177 31,870 32,563 33,255 35,334 38,105 39,491 40,184 41,569 44,341 45,726 48,497 51,269
14
Shaft Space width addendum Tooth modification thickness
Hub diameter Root diameter
Shaft diameter
Deviation
Root form circle diameter d Ff2
Tip diameter
⋅m
e2 = s1
d f2
Adf2
min.
d a2
0,16 0,26 0,36 0,06 0,16 0,26 0,36 0,06 0,16 0,26 0,36 0,06 0,16 0,26 0,36 –0,04 0,06 0,16 0,26 0,36 0,06 0,16 0,26 –0,04 0,06 0,16 0,26 0,36 0,06 0,16 0,26 –0,04 0,06 0,16 0,26 0,36 0,16 0,06 0,26 0,36 0,56 –0,04 0,66 0,56 –0,04
1,441 1,557 1,672 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,672 1,210 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,210 1,326 1,441 1,557 1,672 1,326 1,441 1,557 1,210 1,326 1,441 1,557 1,672 1,441 1,326 1,557 1,672 1,903 1,210 2,019 1,903 1,210
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60
0,25 0,25 0,25 0,25 0,25 0,25 0,25 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,26 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,27 0,28 0,28 0,28 0,28
5,89 6,89 7,89 8,89 9,89 10,89 11,89 12,90 13,90 14,90 15,90 16,90 17,90 18,90 19,90 19,90 20,90 21,90 22,90 23,90 24,90 25,90 26,90 27,90 28,90 29,90 30,90 31,90 32,90 33,90 34,90 35,90 36,90 37,90 38,90 39,90 41,90 44,90 46,90 47,90 49,90 51,91 54,91 57,91 59,91
4,4 5,4 6,4 7,4 8,4 9,4 10,4 11,4 12,4 13,4 14,4 15,4 16,4 17,4 18,4 18,4 19,4 20,4 21,4 22,4 23,4 24,4 25,4 26,4 27,4 28,4 29,4 30,4 31,4 32,4 33,4 34,4 35,4 36,4 37,4 38,4 40,4 43,4 45,4 46,4 48,4 50,4 53,4 56,4 58,4
x1
Tip diameter
Root form circle diameter d Ff1
Root diameter
Deviation
d a1
max.
d f1
Adf1
5,84 6,84 7,84 8,84 9,84 10,84 11,84 12,84 13,84 14,84 15,84 16,84 17,84 18,84 19,84 19,84 20,84 21,84 22,84 23,84 24,84 25,84 26,84 27,84 28,84 29,84 30,84 31,84 32,84 33,84 34,84 35,84 36,84 37,84 38,84 39,84 41,84 44,84 46,84 47,84 49,84 51,84 54,84 57,84 59,84
4,35 5,35 6,35 7,35 8,35 9,35 10,35 11,34 12,34 13,34 14,34 15,34 16,34 17,34 18,34 18,34 19,34 20,34 21,34 22,34 23,34 24,34 25,34 26,34 27,34 28,34 29,34 30,34 31,34 32,34 33,34 34,34 35,34 36,34 37,34 38,34 40,34 43,34 45,34 46,34 48,34 50,33 53,33 56,33 58,33
4,24 5,24 6,24 7,24 8,24 9,24 10,24 11,24 12,24 13,24 14,24 15,24 16,24 17,24 18,24 18,24 19,24 20,24 21,24 22,24 23,24 24,24 25,24 26,24 27,24 28,24 29,24 30,24 31,24 32,24 33,24 34,24 35,24 36,24 37,24 38,24 40,24 43,24 45,24 46,24 48,24 50,24 53,24 56,24 58,24
–0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,47 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,51 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,59 –0,59 –0,59 –0,59
DIN 5480-2:2006-05
Table 9 — Inspection dimensions,
m =
0,8 mm Dimensions in mm
Basic data
Hub dimensions
Reference diameter
Number of teeth
d B
z
DM
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60
6 7 8 10 11 12 13 15 16 17 18 20 21 22 23 24 25 26 27 28 30 31 32 34 35 36 37 38 40 41 42 44 45 46 47 48 51 55 57 58 60 64 66 70 74
1,4 1,5 1,5 1,4 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5
a
Shaft dimensions Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension
M 2
A *M2
DM
M 1
A *M1
k
W k
3,052 3,629 4,794 6,023 6,649 7,779 8,720 9,643 10,759 11,728 12,795 13,736 14,724 15,788 16,753 16,711 17,713 18,776 19,754 20,796 21,760 22,748 23,791 24,742 25,739 26,782 27,765 28,796 29,770 30,760 31,792 32,756 33,752 34,785 35,772 36,796 38,768 41,761 43,776 44,796 46,794 48,770 51,790 54,794 56,774
2,42 2,18 1,83 2,41 2,27 1,95 1,77 2,30 2,03 1,86 1,77 2,08 1,93 1,84 1,76 2,12 1,98 1,89 1,81 1,76 1,93 1,85 1,80 1,96 1,89 1,84 1,79 1,75 1,87 1,82 1,78 1,90 1,85 1,81 1,78 1,75 1,80 1,83 1,77 1,74 1,70 1,84 1,69 1,71 1,82
2,25 2,25 2,25 1,75 1,75 1,75 2,0 1,5 1,75 1,75 1,75 1,5 1,5 1,5 1,75 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5
8,998 9,776 10,939 10,974 11,835 12,903 14,393 14,291 15,992 16,895 17,926 18,378 19,305 20,330 21,920 21,407 22,348 23,369 24,308 25,323 26,397 27,345 28,359 29,417 30,373 31,386 32,340 33,349 34,407 35,367 36,376 37,422 38,388 39,397 40,360 41,365 43,381 46,398 48,374 49,377 51,345 53,428 56,334 59,357 61,430
1,10 1,09 1,12 1,31 1,29 1,30 1,24 1,46 1,38 1,36 1,36 1,52 1,49 1,47 1,40 1,58 1,55 1,53 1,51 1,49 1,57 1,55 1,53 1,61 1,59 1,57 1,55 1,54 1,61 1,59 1,57 1,64 1,62 1,60 1,58 1,57 1,61 1,64 1,61 1,59 1,57 1,66 1,57 1,59 1,67
2 2 2a 2 3a 3 3 3 3a 4 4 4 4 5a 5 4a 5 5 5a 6 6 6 6 6 6a 7 7 7a 7 8a 8 8 8 8a 9 9 9 10 10 a 11 11 11 12 a 13 13
Measuring Nominal circle diameter dimension
3,648 3,786 3,923 3,697 6,011 6,148 6,286 6,060 6,197 8,511 8,648 8,423 8,560 10,874 11,011 8,472 10,786 10,923 11,060 13,374 13,148 13,286 13,423 13,197 13,334 15,648 15,786 15,923 15,697 18,011 18,148 17,923 18,060 18,197 20,511 20,648 20,560 22,786 23,060 25,374 25,648 25,197 28,148 30,374 29,923
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
15
DIN 5480-2:2006-05
8
Module m = 1 mm Table 10 — Nominal dimensions,
m =
1 mm Dimensions in mm
Nominal dimensions
Basic data Reference diameter
Number of teeth
Pitch diameter
Base diameter
d B
z
d
d b
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 22 24 24 26 26 28 28 30 30 32 32 34 34 36 36 38 38 40 44 46 46 48 50 54 56 58
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 22 24 24 26 26 28 28 30 30 32 32 34 34 36 36 38 38 40 44 46 46 48 50 54 56 58
5,196 6,062 6,928 7,794 8,660 9,526 10,392 11,258 12,124 12,990 13,856 14,722 15,588 16,454 17,321 19,053 19,053 20,785 20,785 22,517 22,517 24,249 24,249 25,981 25,981 27,713 27,713 29,445 29,445 31,177 31,177 32,909 32,909 34,641 38,105 39,837 39,837 41,569 43,301 46,765 48,497 50,229
16
Shaft Space width addendum Tooth modification thickness
Hub diameter Root diameter
Deviation
Root form circle diameter d Ff2
Tip diameter d a2
⋅m
e2 = s1
d f2
Adf2
min.
0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 –0,05 0,45 0,45 –0,05 –0,05 0,45 0,45 0,45 –0,05 0,45 0,45
2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 1,513 2,090 2,090 1,513 1,513 2,090 2,090 2,090 1,513 2,090 2,090
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60
0,29 0,29 0,29 0,29 0,29 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,30 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,31 0,32 0,32 0,32 0,32
7,85 8,85 9,85 10,85 11,85 12,86 13,86 14,86 15,86 16,86 17,86 18,86 19,86 20,86 21,86 22,86 23,86 24,86 25,86 26,86 27,86 28,86 29,86 30,86 31,86 32,86 33,86 34,86 35,86 36,86 37,86 38,86 39,86 41,86 44,86 46,86 47,86 49,86 51,87 54,87 57,87 59,87
x1
Shaft diameter
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 43 45 46 48 50 53 56 58
Tip diameter
Root form circle diameter d Ff1
Root diameter
Deviation
d a1
max.
d f1
Adf1
7,8 8,8 9,8 10,8 11,8 12,8 13,8 14,8 15,8 16,8 17,8 18,8 19,8 20,8 21,8 22,8 23,8 24,8 25,8 26,8 27,8 28,8 29,8 30,8 31,8 32,8 33,8 34,8 35,8 36,8 37,8 38,8 39,8 41,8 44,8 46,8 47,8 49,8 51,8 54,8 57,8 59,8
5,95 6,95 7,95 8,95 9,95 10,94 11,94 12,94 13,94 14,94 15,94 16,94 17,94 18,94 19,94 20,94 21,94 22,94 23,94 24,94 25,94 26,94 27,94 28,94 29,94 30,94 31,94 32,94 33,94 34,94 35,94 36,94 37,94 39,94 42,94 44,94 45,94 47,94 49,93 52,93 55,93 57,93
5,80 6,80 7,80 8,80 9,80 10,80 11,80 12,80 13,80 14,80 15,80 16,80 17,80 18,80 19,80 20,80 21,80 22,80 23,80 24,80 25,80 26,80 27,80 28,80 29,80 30,80 31,80 32,80 33,80 34,80 35,80 36,80 37,80 39,80 42,80 44,80 45,80 47,80 49,80 52,80 55,80 57,80
–0,51 –0,51 –0,51 –0,51 –0,51 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,55 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,59 –0,63 –0,63 –0,63 –0,63
DIN 5480-2:2006-05
Table 11 — Inspection dimensions,
m =
1 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions Deviation factor
Number of teeth measured
Nominal dimension
M 1
A *M1
k
W k
4,0 3,25
14,173 13,347
1,01 1,04
2 2
4,810 4,857
1,66 2,03 1,67
3,0 2,75 2,75
14,103 14,395 15,615
1,11 1,13 1,17
2a 2a 3a
4,903 4,950 7,717
8,489 10,369 11,273
1,96 1,68 1,67
2,5 2,5 2,5
15,915 17,081 17,992
1,21 1,23 1,24
3 3 3
7,764 7,810 7,857
1,75 1,75
12,369 13,286
1,69 1,68
2,5 2,25
19,128 19,431
1,27 1,31
3a 3a
7,903 7,950
16 17 18
1,75 1,75 1,75
14,369 15,296 16,370
1,69 1,69 1,70
2,25 2,25 2,25
20,541 21,473 22,568
1,33 1,33 1,35
4a 4 4
10,717 10,764 10,810
21 22
19 20
1,75 1,75
17,304 18,370
1,69 1,70
2,25 2,25
23,508 24,592
1,36 1,37
4 4a
10,857 10,903
23 24 25 26
22 22 24 24
1,5 1,75 1,75 1,75
20,110 20,370 21,311 22,370
1,84 1,70 2,00 1,71
2,25 2,25 2,0 2,25
25,787 26,613 27,109 28,631
1,47 1,39 1,54 1,41
4 5 4a 5
10,497 13,717 10,590 13,810
27 28
26 26
1,5 1,75
24,112 24,370
1,82 1,71
2,0 2,0
29,113 29,982
1,55 1,46
5 5a
13,403 13,903
29 30 31
28 28 30
1,75 1,75 1,75
25,321 26,370 27,325
1,95 1,71 1,93
2,0 2,0 2,0
31,117 31,992 33,121
1,56 1,47 1,57
5 6 5a
13,497 16,717 13,590
32 33
30 32
1,75 1,75
28,370 29,328
1,71 1,91
2,0 2,0
34,002 35,124
1,48 1,58
6 6
16,810 16,403
34 35 36
32 34 34
1,75 1,75 1,75
30,370 31,331 32,370
1,71 1,90 1,71
2,0 2,0 2,0
36,010 37,127 38,018
1,49 1,59 1,50
6a 6 7
16,903 16,497 19,717
37 38 39
36 36 38
1,75 1,75 1,75
33,334 34,370 35,336
1,89 1,72 1,88
2,0 2,0 2,0
39,129 40,025 41,132
1,59 1,51 1,60
6a 7 7
16,590 19,810 19,403
40 42 45
38 40 44
1,75 1,75 1,75
36,370 38,370 41,341
1,72 1,72 1,85
2,0 2,0 2,0
42,032 44,038 47,137
1,52 1,53 1,62
7a 8 8
19,903 22,717 22,403
47 48
46 46
1,75 1,75
43,343 44,370
1,85 1,72
2,0 2,0
49,139 50,053
1,62 1,55
8 9
22,497 25,717
50 52 55
48 50 54
1,75 1,75 1,75
46,370 48,370 51,347
1,72 1,72 1,83
2,0 2,0 2,0
52,057 54,061 57,144
1,55 1,56 1,63
9 9a 9a
25,810 25,903 25,590
58 60
56 58
1,75 1,75
54,370 56,370
1,72 1,72
2,0 2,0
60,072 62,075
1,57 1,58
10 a 11
28,903 31,717
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
d B
z
DM
M 2
A *M2
DM
8 9
6 7
1,75 1,75
4,367 5,189
1,64 1,61
10 11 12
8 9 10
1,75 2,0 1,75
6,368 6,459 8,369
13 14 15
11 12 13
2,0 1,75 1,75
16 17
14 15
18 19 20
a
Deviation Measuring Nominal factor circle diameter dimension
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
17
DIN 5480-2:2006-05
9
Module m = 1,25 mm Table 12 — Nominal dimensions,
m =
1,25 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
Base diameter
d B
z
d
d b
10 11 12 13 14 15 16 17 18 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80
6 7 8 9 10 10 11 12 13 14 14 15 16 17 18 18 19 20 21 22 22 23 24 25 26 26 27 28 29 30 30 32 34 36 37 38 40 42 45 46 48 50 53 54 56 58 60 62
7,50 8,75 10,00 11,25 12,50 12,50 13,75 15,00 16,25 17,50 17,50 18,75 20,00 21,25 22,50 22,50 23,75 25,00 26,25 27,50 27,50 28,75 30,00 31,25 32,50 32,50 33,75 35,00 36,25 37,50 37,50 40,00 42,50 45,00 46,25 47,50 50,00 52,50 56,25 57,50 60,00 62,50 66,25 67,50 70,00 72,50 75,00 77,50
6,495 7,578 8,660 9,743 10,825 10,825 11,908 12,990 14,073 15,155 15,155 16,238 17,321 18,403 19,486 19,486 20,568 21,651 22,733 23,816 23,816 24,898 25,981 27,063 28,146 28,146 29,228 30,311 31,393 32,476 32,476 34,641 36,806 38,971 40,054 41,136 43,301 45,466 48,714 49,796 51,962 54,127 57,374 58,457 60,622 62,787 64,952 67,117
18
Hub diameter
Shaft Space width Root Deviaaddendum Tooth diameter tion modification thickness x1
⋅m
0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,5625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,4375 0,3125 0,1875 0,0625 0,5625 0,3125 0,5625 0,3125 0,1875 0,5625 0,3125 0,5625 0,1875 0,5625 0,3125 0,5625 0,1875 0,5625 0,3125 0,5625 0,8125 0,5625
Shaft diameter
Root form circle diameter d Ff2
Tip diameter
Tip diameter
Root form circle diameter d Ff1
d a1
max.
e2 = s1
d f2
Adf2
min.
d a2
2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,613 2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,036 2,613 2,469 2,324 2,180 2,036 2,613 2,324 2,613 2,324 2,180 2,613 2,324 2,613 2,180 2,613 2,324 2,613 2,180 2,613 2,324 2,613 2,902 2,613
10 11 12 13 14 15 16 17 18 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80
0,34 0,34 0,34 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,36 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37 0,37
9,80 10,80 11,80 12,81 13,81 14,81 15,81 16,81 17,81 19,81 19,81 20,81 21,81 22,81 23,81 24,81 25,81 26,81 27,81 28,81 29,81 30,81 31,81 32,81 33,81 34,81 35,81 36,81 37,81 38,81 39,81 41,81 44,81 46,81 47,81 49,81 51,82 54,82 57,82 59,82 61,82 64,82 67,82 69,82 71,82 74,82 77,82 79,82
7,5 8,5 9,5 10,5 11,5 12,5 13,5 14,5 15,5 17,5 17,5 18,5 19,5 20,5 21,5 22,5 23,5 24,5 25,5 26,5 27,5 28,5 29,5 30,5 31,5 32,5 33,5 34,5 35,5 36,5 37,5 39,5 42,5 44,5 45,5 47,5 49,5 52,5 55,5 57,5 59,5 62,5 65,5 67,5 69,5 72,5 75,5 77,5
9,75 10,75 11,75 12,75 13,75 14,75 15,75 16,75 17,75 19,75 19,75 20,75 21,75 22,75 23,75 24,75 25,75 26,75 27,75 28,75 29,75 30,75 31,75 32,75 33,75 34,75 35,75 36,75 37,75 38,75 39,75 41,75 44,75 46,75 47,75 49,75 51,75 54,75 57,75 59,75 61,75 64,75 67,75 69,75 71,75 74,75 77,75 79,75
7,45 8,45 9,45 10,44 11,44 12,44 13,44 14,44 15,44 17,44 17,44 18,44 19,44 20,44 21,44 22,44 23,44 24,44 25,44 26,44 27,44 28,44 29,44 30,44 31,44 32,44 33,44 34,44 35,44 36,44 37,44 39,44 42,44 44,44 45,44 47,44 49,43 52,43 55,43 57,43 59,43 62,43 65,43 67,43 69,43 72,43 75,43 77,43
Root Deviation diameter d f1
7,25 8,25 9,25 10,25 11,25 12,25 13,25 14,25 15,25 17,25 17,25 18,25 19,25 20,25 21,25 22,25 23,25 24,25 25,25 26,25 27,25 28,25 29,25 30,25 31,25 32,25 33,25 34,25 35,25 36,25 37,25 39,25 42,25 44,25 45,25 47,25 49,25 52,25 55,25 57,25 59,25 62,25 65,25 67,25 69,25 72,25 75,25 77,25
Adf1
–0,56 –0,56 –0,56 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,60 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,64 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68 –0,68
DIN 5480-2:2006-05
Table 13 — Inspection dimensions,
m =
1,25 mm Dimensions in mm
Basic data
Hub dimensions
Reference Number of Measuring diameter teeth circle diameter
a
Shaft dimensions
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension W k
d B
z
DM
M 2
A *M2
DM
M 1
A *M1
k
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80
6 7 8 9 10 10 11 12 13 14 14 15 16 17 18 18 19 20 21 22 22 23 24 25 26 26 27 28 29 30 30 32 34 36 37 38 40 42 45 46 48 50 53 54 56 58 60 62
2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25
5,276 6,052 7,230 8,007 9,060 10,276 11,132 12,249 13,099 14,158 15,276 16,170 17,257 18,143 19,193 20,276 21,192 22,261 23,170 24,212 25,276 26,207 27,264 28,187 29,224 30,276 31,217 32,266 33,200 34,232 35,276 37,267 40,276 42,268 43,216 45,276 47,269 50,276 53,227 55,276 57,270 60,276 63,235 65,276 67,271 70,276 73,271 75,276
1,71 1,85 2,13 2,41 2,99 1,72 1,81 1,95 2,08 2,26 1,72 1,79 1,88 1,96 2,07 1,73 1,78 1,85 1,91 1,99 1,73 1,77 1,83 1,87 1,94 1,73 1,77 1,81 1,85 1,90 1,73 1,80 1,73 1,79 1,82 1,73 1,79 1,73 1,81 1,73 1,78 1,73 1,79 1,73 1,77 1,73 1,70 1,73
4,5 3,5 3,0 2,75 2,5 3,25 3,0 2,75 2,5 2,5 3,0 2,75 2,5 2,5 2,5 2,75 2,75 2,5 2,5 2,5 2,75 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5
16,629 15,279 15,554 15,851 16,503 19,075 19,417 20,059 20,360 21,548 23,602 23,940 24,477 25,433 26,578 28,050 29,026 29,513 30,480 31,599 33,103 33,423 34,540 35,514 36,614 37,477 38,460 39,561 40,540 41,627 42,502 44,577 47,523 49,590 50,576 52,540 54,602 57,554 60,600 62,566 64,619 67,577 70,617 72,586 74,632 77,594 80,552 82,601
1,03 1,08 1,20 1,25 1,37 1,19 1,23 1,31 1,38 1,43 1,28 1,33 1,41 1,43 1,47 1,36 1,38 1,45 1,47 1,51 1,40 1,45 1,48 1,50 1,53 1,46 1,48 1,51 1,53 1,55 1,48 1,53 1,50 1,54 1,56 1,52 1,56 1,54 1,59 1,55 1,58 1,56 1,60 1,57 1,60 1,58 1,56 1,59
2 2 2 2 2 3a 3 3 3 3 3a 3a 3a 3a 4a 4 4 4 4 4 5 5 5 5 5 5a 5a 5a 5a 6a 6 6 7 7 7 7a 7a 8 8 9 9 9a 9a 10 10 11 11 11 a
6,013 5,946 5,879 5,813 5,746 9,647 9,580 9,513 9,446 9,379 9,879 9,813 9,746 9,679 13,013 13,513 13,446 13,379 13,313 13,246 17,147 17,080 17,013 16,946 16,879 17,379 17,313 17,246 17,179 20,513 21,013 20,879 24,647 24,513 24,446 24,879 24,746 28,513 28,313 32,147 32,013 32,379 32,179 36,013 35,879 39,647 40,013 39,879
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
19
DIN 5480-2:2006-05
10 Module
m =
1,5 mm Table 14 — Nominal dimensions,
m =
1,5 mm Dimensions in mm
Nominal dimensions
Basic data Reference diameter
Number of teeth
Pitch diameter
Base diameter
d B
z
d
d b
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110
6 7 8 8 9 10 10 11 12 12 13 14 14 15 16 16 17 18 18 19 20 20 21 22 22 23 24 24 25 26 28 30 30 32 33 35 37 38 40 42 44 45 46 48 50 52 53 55 57 58 60 62 64 64 68 72
9,0 10,5 12,0 12,0 13,5 15,0 15,0 16,5 18,0 18,0 19,5 21,0 21,0 22,5 24,0 24,0 25,5 27,0 27,0 28,5 30,0 30,0 31,5 33,0 33,0 34,5 36,0 36,0 37,5 39,0 42,0 45,0 45,0 48,0 49,5 52,5 55,5 57,0 60,0 63,0 66,0 67,5 69,0 72,0 75,0 78,0 79,5 82,5 85,5 87,0 90,0 93,0 96,0 96,0 102,0 108,0
7,794 9,093 10,392 10,392 11,691 12,990 12,990 14,289 15,588 15,588 16,887 18,187 18,187 19,486 20,785 20,785 22,084 23,383 23,383 24,682 25,981 25,981 27,280 28,579 28,579 29,878 31,177 31,177 32,476 33,775 36,373 38,971 38,971 41,569 42,868 45,466 48,064 49,363 51,962 54,560 57,158 58,457 59,756 62,354 64,952 67,550 68,849 71,447 74,045 75,344 77,942 80,540 83,138 83,138 88,335 93,531
20
Shaft Space width addendum Tooth modification thickness x1
⋅m
0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,175 0,675 0,425 0,675 0,675 0,175 0,675 0,175 0,425 0,425 0,425 0,675 0,175 0,175 0,175 0,425 0,675 0,675 0,675 0,175 0,425 0,425 0,425 0,675 0,175 0,175 0,175 1,175 0,675 0,175
Hub diameter
Shaft diameter
Deviation
Root form circle diameter d Ff2
Tip diameter
d f2
Adf2
min.
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110
0,39 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,40 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,41 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,42 0,44 0,44
11,75 12,76 13,76 14,76 15,76 16,76 17,76 18,76 19,76 20,76 21,76 22,76 23,76 24,76 25,76 26,76 27,76 28,76 29,76 30,76 31,76 32,76 33,76 34,76 35,76 36,76 37,76 38,76 39,76 41,76 44,76 46,76 47,76 49,76 51,77 54,77 57,77 59,77 61,77 64,77 67,77 69,77 71,77 74,77 77,77 79,77 81,77 84,77 87,77 89,77 91,77 94,77 97,77 99,77 104,78 109,78
Root diameter
e2 = s1
3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 2,558 3,136 2,847 3,136 3,136 2,558 3,136 2,558 2,847 2,847 2,847 3,136 2,558 2,558 2,558 2,847 3,136 3,136 3,136 2,558 2,847 2,847 2,847 3,136 2,558 2,558 2,558 3,713 3,136 2,558
Tip diameter
Root form circle diameter d Ff1
Root diameter
Deviation
d a2
d a1
max.
d f1
Adf1
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 39 42 44 45 47 49 52 55 57 59 62 65 67 69 72 75 77 79 82 85 87 89 92 95 97 102 107
11,7 12,7 13,7 14,7 15,7 16,7 17,7 18,7 19,7 20,7 21,7 22,7 23,7 24,7 25,7 26,7 27,7 28,7 29,7 30,7 31,7 32,7 33,7 34,7 35,7 36,7 37,7 38,7 39,7 41,7 44,7 46,7 47,7 49,7 51,7 54,7 57,7 59,7 61,7 64,7 67,7 69,7 71,7 74,7 77,7 79,7 81,7 84,7 87,7 89,7 91,7 94,7 97,7 99,7 104,7 109,7
8,95 9,94 10,94 11,94 12,94 13,94 14,94 15,94 16,94 17,94 18,94 19,94 20,94 21,94 22,94 23,94 24,94 25,94 26,94 27,94 28,94 29,94 30,94 31,94 32,94 33,94 34,94 35,94 36,94 38,94 41,94 43,94 44,94 46,94 48,93 51,93 54,93 56,93 58,93 61,93 64,93 66,93 68,93 71,93 74,93 76,93 78,93 81,93 84,93 86,93 88,93 91,93 94,93 96,93 101,92 106,92
8,70 9,70 10,70 11,70 12,70 13,70 14,70 15,70 16,70 17,70 18,70 19,70 20,70 21,70 22,70 23,70 24,70 25,70 26,70 27,70 28,70 29,70 30,70 31,70 32,70 33,70 34,70 35,70 36,70 38,70 41,70 43,70 44,70 46,70 48,70 51,70 54,70 56,70 58,70 61,70 64,70 66,70 68,70 71,70 74,70 76,70 78,70 81,70 84,70 86,70 88,70 91,70 94,70 96,70 101,70 106,70
–0,61 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,65 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,69 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,73 –0,79 –0,79
DIN 5480-2:2006-05
Table 15 — Inspection dimensions,
m =
1,5 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
d B
z
DM
M 2
A *M2
DM
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110
6 7 8 8 9 10 10 11 12 12 13 14 14 15 16 16 17 18 18 19 20 20 21 22 22 23 24 24 25 26 28 30 30 32 33 35 37 38 40 42 44 45 46 48 50 52 53 55 57 58 60 62 64 64 68 72
2,75 2,75 2,5 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75 2,75
6,180 6,868 8,877 9,180 9,939 10,985 12,181 12,983 14,038 15,181 16,014 17,068 18,181 19,036 20,087 21,181 22,053 23,101 24,181 25,067 26,111 27,181 28,078 29,118 30,181 31,087 32,125 33,181 34,094 36,181 39,181 41,138 42,181 44,141 46,115 49,119 52,122 54,181 56,150 59,151 62,153 64,133 66,181 69,181 72,181 74,157 76,140 79,142 82,143 84,181 86,161 89,161 92,162 94,168 99,181 104,164
1,77 2,18 2,13 1,76 2,03 2,67 1,76 1,96 2,33 1,75 1,91 2,18 1,75 1,88 2,09 1,75 1,86 2,03 1,75 1,85 1,99 1,74 1,84 1,96 1,74 1,83 1,93 1,74 1,82 1,74 1,74 1,88 1,74 1,87 1,80 1,79 1,79 1,74 1,84 1,83 1,83 1,78 1,74 1,74 1,74 1,81 1,77 1,77 1,77 1,74 1,80 1,80 1,80 1,69 1,74 1,79
5,5 4,0 3,5 4,5 3,5 3,25 4,0 3,5 3,0 3,5 3,25 3,0 3,5 3,25 3,0 3,5 3,25 3,0 3,25 3,0 3,0 3,25 3,0 3,0 3,25 3,0 3,0 3,25 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0
a
Deviation factor
Number of teeth measured
Nominal dimension
M 1
A *M1
k
W k
20,173 17,756 18,144 21,155 19,788 20,593 23,127 22,914 22,995 25,011 25,382 26,022 28,074 28,446 29,044 31,127 31,498 32,063 33,532 33,883 35,078 36,564 36,914 38,092 39,593 39,939 41,103 42,618 42,961 44,972 47,988 50,130 51,003 53,138 55,026 58,038 61,049 63,047 65,160 68,164 71,169 73,084 75,079 78,086 81,092 83,182 85,109 88,114 91,119 93,113 95,192 98,195 101,197 103,034 108,133 113,204
1,02 1,10 1,23 1,11 1,21 1,31 1,18 1,25 1,38 1,26 1,32 1,41 1,29 1,35 1,44 1,31 1,37 1,46 1,36 1,43 1,48 1,38 1,45 1,49 1,40 1,46 1,51 1,42 1,48 1,46 1,47 1,54 1,48 1,55 1,52 1,53 1,54 1,52 1,58 1,58 1,59 1,57 1,55 1,55 1,56 1,61 1,59 1,59 1,60 1,58 1,62 1,62 1,63 1,56 1,60 1,64
Deviation Measuring Nominal factor circle diameter dimension
2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 7 7 7 7 8 8 8 9 9 9 9 10 10 10 11 11 11 11 12 12 13
a a a a
a a a
a a
a
a
a a
a
a a
a
a a
7,216 7,035 6,855 7,355 7,175 6,995 11,576 11,396 11,216 11,716 11,535 11,355 11,855 11,675 11,495 16,076 15,896 15,716 16,216 16,035 15,855 16,355 16,175 15,995 20,576 20,396 20,216 20,716 20,535 20,855 25,076 24,716 25,216 24,855 25,175 29,396 29,535 29,855 29,495 33,716 33,855 34,175 38,576 38,716 38,855 38,495 42,896 43,035 43,175 47,576 47,216 47,355 47,495 52,576 52,355 56,216
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
21
DIN 5480-2:2006-05
11 Module
m =
1,75 mm Table 16 — Nominal dimensions,
m =
1,75 mm Dimensions in mm
Basic data ReferNumber ence of teeth diameter d B
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 110 120 120 a
22
z
6 6 7 a 8 8 9 9 10 10 11 12 12 13 13 14 14 15 16 16 17 17 18 18 19 20 20 21 21 22 24 25 26 27 28 30 32 33 34 36 37 38 40 41 43 44 45 47 49 50 51 53 54 56 58 60 61 66 67
Nominal dimensions
Pitch diameter
Base diameter
Shaft addendum modification
d
d b
x1 ⋅ m
10,50 10,50 12,25 14,00 14,00 15,75 15,75 17,50 17,50 19,25 21,00 21,00 22,75 22,75 24,50 24,50 26,25 28,00 28,00 29,75 29,75 31,50 31,50 33,25 35,00 35,00 36,75 36,75 38,50 42,00 43,75 45,50 47,25 49,00 52,50 56,00 57,75 59,50 63,00 64,75 66,50 70,00 71,75 75,25 77,00 78,75 82,25 85,75 87,50 89,25 92,75 94,50 98,00 101,50 105,00 106,75 115,50 117,25
9,093 9,093 10,609 12,124 12,124 13,640 13,640 15,155 15,155 16,671 18,187 18,187 19,702 19,702 21,218 21,218 22,733 24,249 24,249 25,764 25,764 27,280 27,280 28,795 30,311 30,311 31,826 31,826 33,342 36,373 37,889 39,404 40,920 42,435 45,466 48,497 50,013 51,529 54,560 56,075 57,591 60,622 62,137 65,168 66,684 68,200 71,231 74,262 75,777 77,293 80,324 81,839 84,870 87,902 90,933 92,448 100,026 101,541
0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,2875 0,7875 0,4125 0,0375 0,5375 0,1625 0,6625 0,7875 0,5375 0,6625 0,2875 0,4125 0,5375 0,2875 0,0375 0,1625 0,2875 0,0375 0,6625 0,7875 0,0375 0,6625 0,4125 0,5375 0,6625 0,4125 0,1625 0,2875 0,4125 0,1625 0,7875 0,0375 0,7875 1,5375 0,6625 1,2875 0,4125
Space width Tooth thickness e2
= s1
3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,081 3,658 3,225 2,792 3,370 2,937 3,514 3,658 3,370 3,514 3,081 3,225 3,370 3,081 2,792 2,937 3,081 2,792 3,514 3,658 2,792 3,514 3,225 3,370 3,514 3,225 2,937 3,081 3,225 2,937 3,658 2,792 3,658 4,524 3,514 4,236 3,225
Hub diameter Root diameter
Deviation
d f2
Adf2
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 110 120 120
0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,46 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,47 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,49 0,51 0,51 0,51 0,51 0,51
S haft diameter
Root form circle Tip Tip diameter diameter diameter d Ff2
A special tool is required for manufacturing splined shafts by shaping.
min. 12,71 13,71 14,71 15,71 16,71 17,71 18,71 19,71 20,71 21,71 22,71 23,71 24,71 25,72 26,72 27,72 28,72 29,72 30,72 31,72 32,72 33,72 34,72 35,72 36,72 37,72 38,72 39,72 41,72 44,72 46,72 47,72 49,72 51,73 54,73 57,73 59,73 61,73 64,73 67,73 69,73 71,73 74,73 77,73 79,73 81,73 84,73 87,73 89,73 91,73 94,73 97,73 99,73 104,74 109,74 109,74 119,74 119,74
Root form circle diameter
Root diameter
Deviation
d Ff1 d a2
9,5 10,5 11,5 12,5 13,5 14,5 15,5 16,5 17,5 18,5 19,5 20,5 21,5 22,5 23,5 24,5 25,5 26,5 27,5 28,5 29,5 30,5 31,5 32,5 33,5 34,5 35,5 36,5 38,5 41,5 43,5 44,5 46,5 48,5 51,5 54,5 56,5 58,5 61,5 64,5 66,5 68,5 71,5 74,5 76,5 78,5 81,5 84,5 86,5 88,5 91,5 94,5 96,5 101,5 106,5 106,5 116,5 116,5
d a1
12,65 13,65 14,65 15,65 16,65 17,65 18,65 19,65 20,65 21,65 22,65 23,65 24,65 25,65 26,65 27,65 28,65 29,65 30,65 31,65 32,65 33,65 34,65 35,65 36,65 37,65 38,65 39,65 41,65 44,65 46,65 47,65 49,65 51,65 54,65 57,65 59,65 61,65 64,65 67,65 69,65 71,65 74,65 77,65 79,65 81,65 84,65 87,65 89,65 91,65 94,65 97,65 99,65 104,65 109,65 109,65 119,65 119,65
max. 9,44 10,44 11,44 12,44 13,44 14,44 15,44 16,44 17,44 18,44 19,44 20,44 21,44 22,43 23,43 24,43 25,43 26,43 27,43 28,43 29,43 30,43 31,43 32,43 33,43 34,43 35,43 36,43 38,43 41,43 43,43 44,43 46,43 48,42 51,42 54,42 56,42 58,42 61,42 64,42 66,42 68,42 71,42 74,42 76,42 78,42 81,42 84,42 86,42 88,42 91,42 94,42 96,42 101,41 106,41 106,41 116,41 116,41
d f1
9,15 10,15 11,15 12,15 13,15 14,15 15,15 16,15 17,15 18,15 19,15 20,15 21,15 22,15 23,15 24,15 25,15 26,15 27,15 28,15 29,15 30,15 31,15 32,15 33,15 34,15 35,15 36,15 38,15 41,15 43,15 44,15 46,15 48,15 51,15 54,15 56,15 58,15 61,15 64,15 66,15 68,15 71,15 74,15 76,15 78,15 81,15 84,15 86,15 88,15 91,15 94,15 96,15 101,15 106,15 106,15 116,15 116,15
Adf1
0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,74 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,78 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,84 –0,90 –0,90 –0,90 –0,90 –0,90
DIN 5480-2:2006-05
Table 17 — Inspection dimensions,
m =
1,75 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
d B
z
DM
M 2
A*M2
DM
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 110 120 120
6 6 7 8 8 9 9 10 10 11 12 12 13 13 14 14 15 16 16 17 17 18 18 19 20 20 21 21 22 24 25 26 27 28 30 32 33 34 36 37 38 40 41 43 44 45 47 49 50 51 53 54 56 58 60 61 66 67
3,0 3,25 3,25 3,0 3,25 3,0 3,25 3,0 3,25 3,25 3,0 3,25 3,0 3,25 3,25 3,25 3,25 3,0 3,25 3,0 3,25 3,25 3,25 3,25 3,0 3,25 3,0 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,0 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,25 3,5 3,25 3,5 3,25
6,738 7,082 7,623 9,534 10,023 11,495 11,835 13,789 14,084 14,813 16,696 17,048 18,607 18,911 19,974 21,085 21,889 23,743 24,059 25,663 25,952 27,006 28,085 28,932 30,766 31,065 32,697 32,977 35,085 38,069 39,995 41,035 42,978 45,072 48,043 51,796 52,963 55,048 58,010 61,024 63,086 65,019 68,030 71,019 73,077 75,035 78,025 81,005 83,061 85,030 88,011 91,086 93,040 98,086 102,327 103,049 112,335 113,043
2,42 1,82 2,74 3,42 2,13 2,27 1,87 2,01 1,78 2,11 2,26 1,95 2,02 1,83 2,13 1,77 1,97 2,05 1,88 1,93 1,81 2,00 1,76 1,91 1,97 1,85 1,89 1,79 1,75 1,83 1,78 1,90 1,85 1,81 1,87 1,86 1,89 1,85 1,90 1,77 1,75 1,88 1,76 1,80 1,78 1,76 1,79 1,83 1,81 1,79 1,82 1,74 1,83 1,74 1,69 1,75 1,72 1,77
4,5 6 4,5 3,75 4,5 3,75 4,5 3,75 4,5 3,75 3,5 4,0 3,5 4,0 3,5 4,0 3,75 3,5 3,75 3,5 3,75 3,5 4,0 3,5 3,5 3,5 3,5 3,5 3,75 3,5 3,5 3,5 3,5 3,5 3,5 3,25 3,25 3,25 3,25 3,5 3,5 3,25 3,5 3,5 3,5 3,5 3,25 3,25 3,25 3,25 3,25 3,5 3,25 3,5 3,5 3,5 3,5 3,25
a
Deviation factor
Number of teeth measured
Nominal dimension
M 1
A*M1
k
W k
18,639 22,624 20,227 20,109 22,620 21,799 24,299 24,046 26,587 25,788 26,558 28,607 28,344 30,383 30,494 32,546 32,950 33,606 35,078 35,440 36,904 37,546 39,654 39,393 40,638 41,485 42,502 43,343 46,082 48,526 50,404 51,611 53,500 55,558 58,633 60,988 62,902 64,950 67,995 71,519 73,555 75,001 78,544 81,605 83,636 85,565 87,912 90,952 92,982 94,923 97,960 101,620 103,018 108,632 113,488 113,623 123,563 122,955
1,13 1,03 1,12 1,29 1,17 1,28 1,16 1,30 1,19 1,29 1,41 1,29 1,39 1,28 1,40 1,29 1,36 1,46 1,37 1,45 1,36 1,45 1,34 1,44 1,50 1,44 1,49 1,43 1,41 1,47 1,46 1,51 1,50 1,50 1,53 1,60 1,58 1,57 1,61 1,53 1,52 1,62 1,54 1,57 1,56 1,55 1,60 1,62 1,62 1,61 1,63 1,57 1,65 1,58 1,54 1,59 1,57 1,63
Measuring Nominal circle diameter dimension
2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 9 10 10 11 11 11 12 12
a a a a a
a
a a
a
a
a a a
a
a
a
7,918 8,418 8,125 7,831 8,331 8,038 8,538 8,244 13,505 13,212 12,918 13,418 13,125 13,625 13,331 13,831 13,538 13,244 13,744 13,450 18,712 18,418 18,918 18,625 18,331 18,831 18,538 19,038 24,005 23,918 24,125 23,831 24,038 24,244 28,918 28,831 29,038 29,244 33,918 34,625 34,831 34,244 39,712 39,625 39,831 40,038 44,712 44,625 44,831 45,038 44,950 50,418 49,831 55,505 56,418 55,625 61,418 60,625
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
23
DIN 5480-2:2006-05
12 Module
m =
2 mm Table 18 — Nominal dimensions,
m =
2 mm Dimensions in mm
Nominal dimensions
Basic data Reference diameter
Number of teeth
Pitch diameter
Base diameter
d
z
d
d
15 16 17 18 20 22 25 28 30 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150
6 6 7 7 8 9 11 12 13 a 14 14 16 17 a 18 18 a 20 21 22 22 24 24 26 28 28 30 31 32 34 34 36 38 38 40 41 42 44 44 46 48 48 51 54 58 64 68 74
12 12 14 14 16 18 22 24 26 28 28 32 34 36 36 40 42 44 44 48 48 52 56 56 60 62 64 68 68 72 76 76 80 82 84 88 88 92 96 96 102 108 116 128 136 148
10,392 10,392 12,124 12,124 13,856 15,588 19,053 20,785 22,517 24,249 24,249 27,713 29,445 31,177 31,177 34,641 36,373 38,105 38,105 41,569 41,569 45,033 48,497 48,497 51,962 53,694 55,426 58,890 58,890 62,354 65,818 65,818 69,282 71,014 72,746 76,210 76,210 79,674 83,138 83,138 88,335 93,531 100,459 110,851 117,779 128,172
B
a
24
b
Shaft Space width addendum Tooth modification thickness x
1
⋅m
0,4 0,9 0,4 0,9 0,9 0,9 0,4 0,9 0,9 –0,1 0,9 0,4 0,4 –0,1 0,9 –0,1 0,4 0,4 0,9 –0,1 0,9 0,4 –0,1 0,9 –0,1 0,4 0,9 –0,1 0,9 0,4 –0,1 0,9 –0,1 0,4 0,9 –0,1 0,9 0,4 –0,1 0,9 0,4 –0,1 0,9 –0,1 0,9 –0,1
2 = s1
e
3,603 4,181 3,603 4,181 4,181 4,181 3,603 4,181 4,181 3,026 4,181 3,603 3,603 3,026 4,181 3,026 3,603 3,603 4,181 3,026 4,181 3,603 3,026 4,181 3,026 3,603 4,181 3,026 4,181 3,603 3,026 4,181 3,026 3,603 4,181 3,026 4,181 3,603 3,026 4,181 3,603 3,026 4,181 3,026 4,181 3,026
Hub diameter Root diameter d
f2
15 16 17 18 20 22 25 28 30 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150
Deviation A
df2
0,51 0,51 0,51 0,51 0,51 0,51 0,51 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,52 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,54 0,56 0,56 0,56 0,56 0,56 0,56
A special tool is required for manufacturing splined hubs by shaping.
Root form circle diameter d Ff2
min. 14,66 15,66 16,66 17,66 19,66 21,66 24,66 27,67 29,67 29,67 31,67 34,67 36,67 37,67 39,67 41,67 44,67 46,67 47,67 49,67 51,68 54,68 57,68 59,68 61,68 64,68 67,68 69,68 71,68 74,68 77,68 79,68 81,68 84,68 87,68 89,68 91,68 94,68 97,68 99,68 104,69 109,69 119,69 129,69 139,69 149,69
Shaft diameter Tip diameter d
a2
11 12 13 14 16 18 21 24 26 26 28 31 33 34 36 38 41 43 44 46 48 51 54 56 58 61 64 66 68 71 74 76 78 81 84 86 88 91 94 96 101 106 116 126 136 146
Tip diameter d
a1
14,6 15,6 16,6 17,6 19,6 21,6 24,6 27,6 29,6 29,6 31,6 34,6 36,6 37,6 39,6 41,6 44,6 46,6 47,6 49,6 51,6 54,6 57,6 59,6 61,6 64,6 67,6 69,6 71,6 74,6 77,6 79,6 81,6 84,6 87,6 89,6 91,6 94,6 97,6 99,6 104,6 109,6 119,6 129,6 139,6 149,6
Root form circle diameter d Ff1
max. 10,94 11,94 12,94 13,94 15,94 17,94 20,94 23,93 25,93 25,93 27,93 30,93 32,93 33,93 35,93 37,93 40,93 42,93 43,93 45,93 47,92 50,92 53,92 55,92 57,92 60,92 63,92 65,92 67,92 70,92 73,92 75,92 77,92 80,92 83,92 85,92 87,92 90,92 93,92 95,92 100,91 105,91 115,91 125,91 135,91 145,91
Root diameter d
f1
10,60 11,60 12,60 13,60 15,60 17,60 20,60 23,60 25,60 25,60 27,60 30,60 32,60 33,60 35,60 37,60 40,60 42,60 43,60 45,60 47,60 50,60 53,60 55,60 57,60 60,60 63,60 65,60 67,60 70,60 73,60 75,60 77,60 80,60 83,60 85,60 87,60 90,60 93,60 95,60 100,60 105,60 115,60 125,60 135,60 145,60
Deviation
A
df1
–0,79 –0,79 –0,79 –0,79 –0,79 –0,79 –0,79 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,83 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,89 –0,95 –0,95 –0,95 –0,95 –0,95 –0,95
DIN 5480-2:2006-05
Table 19 — Inspection dimensions,
m =
2 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension
d B
z
DM
M 2
A*M2
DM
M 1
A*M1
k
W k
15 16 17 18 20 22 25 28 30 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150
6 6 7 7 8 9 11 12 13 14 14 16 17 18 18 20 21 22 22 24 24 26 28 28 30 31 32 34 34 36 38 38 40 41 42 44 44 46 48 48 51 54 58 64 68 74
3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5 3,5
7,629 8,735 9,324 10,379 12,736 14,460 17,478 20,738 22,547 22,484 24,738 27,711 29,571 30,566 32,739 34,589 37,603 39,720 40,739 42,621 44,740 47,723 50,642 52,740 54,650 57,648 60,740 62,663 64,740 67,729 70,672 72,740 74,676 77,671 80,740 82,683 84,740 87,732 90,688 92,740 97,685 102,695 112,741 122,702 132,741 142,708
2,42 1,64 2,18 1,61 1,66 1,64 1,96 1,68 1,67 2,41 1,69 1,88 1,86 2,15 1,70 2,08 1,84 1,84 1,70 2,00 1,71 1,82 1,95 1,71 1,93 1,80 1,71 1,90 1,71 1,79 1,88 1,72 1,87 1,78 1,72 1,85 1,72 1,78 1,84 1,72 1,77 1,83 1,72 1,81 1,72 1,80
5,5 8,0 5,0 6,0 6,0 5,5 4,5 5,0 5,0 4,0 4,5 4,0 4,0 4,0 4,5 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0
22,212 28,345 22,695 25,588 28,206 28,790 29,898 34,161 35,984 34,144 37,016 39,000 40,857 42,181 45,137 46,195 48,938 51,074 51,912 54,218 55,939 59,109 62,235 63,984 66,242 69,058 72,021 74,253 76,036 79,166 82,263 84,063 86,267 89,123 92,086 94,275 96,096 99,202 102,281 104,114 109,165 114,289 124,150 134,299 144,177 154,306
1,11 1,01 1,13 1,06 1,11 1,13 1,28 1,23 1,24 1,46 1,30 1,42 1,42 1,50 1,35 1,52 1,46 1,47 1,43 1,54 1,44 1,50 1,56 1,47 1,57 1,53 1,49 1,59 1,50 1,55 1,60 1,52 1,61 1,57 1,54 1,62 1,54 1,58 1,62 1,55 1,59 1,63 1,58 1,65 1,60 1,66
2 2 2 2 2a 2a 3a 3 3 3 3a 3a 4a 3a 4 4 4 4a 5 4a 5 5 5 6 5a 6 6a 6 7 7 7 7a 7 8a 8 8 8a 8a 8a 9 9 9a 11 11 12 a 13
9,121 9,621 9,214 9,714 9,807 9,900 15,028 15,621 15,714 14,807 15,807 15,493 21,028 15,179 21,621 20,807 21,400 21,493 27,434 21,179 27,621 27,307 26,993 33,434 27,179 33,214 33,807 32,993 39,434 39,121 38,807 39,807 38,993 45,028 45,621 44,807 45,807 45,493 45,179 51,621 51,400 51,179 63,434 62,993 69,807 74,807
a
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
25
DIN 5480-2:2006-05
13 Module
m =
2,5 mm Table 20 — Nominal dimensions,
m =
2,5 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumber ence of teeth diameter d B
z
20 22 25 28 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150
6 7 8 10 10 11 12 13 14 14 15 16 17 18 18 19 20 22 22 23 24 26 26 27 28 30 30 31 32 34 34 35 36 38 38 40 42 46 50 54 58
26
Pitch diameter
Base diameter
d
d b
15,0 12,990 17,5 15,155 20,0 17,321 25,0 21,651 25,0 21,651 27,5 23,816 30,0 25,981 32,5 28,146 35,0 30,311 35,0 30,311 37,5 32,476 40,0 34,641 42,5 36,806 45,0 38,971 45,0 38,971 47,5 41,136 50,0 43,301 55,0 47,631 55,0 47,631 57,5 49,796 60,0 51,962 65,0 56,292 65,0 56,292 67,5 58,457 70,0 60,622 75,0 64,952 75,0 64,952 77,5 67,117 80,0 69,282 85,0 73,612 85,0 73,612 87,5 75,777 90,0 77,942 95,0 82,272 95,0 82,272 100,0 86,603 105,0 90,933 115,0 99,593 125,0 108,253 135,0 116,913 145,0 125,574
Shaft Space width addendum Tooth modification thickness x1
⋅m
1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,875 0,125 1,125 0,875 1,125 0,875 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 0,875 1,125 0,125 1,125 1,125 1,125 1,125 1,125 1,125 1,125
Hub diameter
Shaft diameter
Deviation
Root form circle diameter d Ff2
Tip diameter
Tip diameter
Root form circle diameter d Ff1
d f2
Adf2
min.
d a2
d a1
max.
20 22 25 28 30 32 35 37 38 40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150
0,61 0,61 0,61 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,62 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,66 0,66 0,66 0,66 0,66 0,66
Root diameter
e2 = s1
5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,937 4,071 5,226 4,937 5,226 4,937 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 4,937 5,226 4,071 5,226 5,226 5,226 5,226 5,226 5,226 5,226
19,56 21,56 24,56 27,57 29,57 31,57 34,57 36,57 37,57 39,57 41,57 44,57 46,57 47,57 49,57 51,58 54,58 57,58 59,58 61,58 64,58 67,58 69,58 71,58 74,58 77,58 79,58 81,58 84,58 87,58 89,58 91,58 94,58 97,58 99,58 104,59 109,59 119,59 129,59 139,59 149,59
15 17 20 23 25 27 30 32 33 35 37 40 42 43 45 47 50 53 55 57 60 63 65 67 70 73 75 77 80 83 85 87 90 93 95 100 105 115 125 135 145
19,5 21,5 24,5 27,5 29,5 31,5 34,5 36,5 37,5 39,5 41,5 44,5 46,5 47,5 49,5 51,5 54,5 57,5 59,5 61,5 64,5 67,5 69,5 71,5 74,5 77,5 79,5 81,5 84,5 87,5 89,5 91,5 94,5 97,5 99,5 104,5 109,5 119,5 129,5 139,5 149,5
14,94 16,94 19,94 22,93 24,93 26,93 29,93 31,93 32,93 34,93 36,93 39,93 41,93 42,93 44,93 46,92 49,92 52,92 54,92 56,92 59,92 62,92 64,92 66,92 69,92 72,92 74,92 76,92 79,92 82,92 84,92 86,92 89,92 92,92 94,92 99,91 104,91 114,91 124,91 134,91 144,91
Root Deviation diameter d f1
14,50 16,50 19,50 22,50 24,50 26,50 29,50 31,50 32,50 34,50 36,50 39,50 41,50 42,50 44,50 46,50 49,50 52,50 54,50 56,50 59,50 62,50 64,50 66,50 69,50 72,50 74,50 76,50 79,50 82,50 84,50 86,50 89,50 92,50 94,50 99,50 104,50 114,50 124,50 134,50 144,50
Adf1
–0,89 –0,89 –0,89 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,93 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –0,99 –1,05 –1,05 –1,05 –1,05 –1,05 –1,05
DIN 5480-2:2006-05
Table 21 — Inspection dimensions,
m =
2,5 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension
d B
z
DM
M 2
A*M2
DM
M 1
A*M1
k
W k
20
6
4,5
10,551
1,71
9,0
33,258
1,03
2
12,026
22
7
4,5
12,105
1,85
7,0
30,558
1,08
2
11,892 12,259
25
8
4,5
15,552
1,72
7,0
34,113
1,13
2a
28
10
4,25
19,115
2,30
5,0
33,006
1,37
2
11,491
30
10
4,5
20,552
1,72
6,5
38,151
1,19
3a
19,293
32
11
4,5
22,265
1,81
6,0
38,835
1,23
3
19,159
35
12
4,5
25,552
1,72
6,0
42,093
1,25
3
19,526
37
13
4,5
27,308
1,80
5,5
42,764
1,30
3
19,392
38
14
4,5
28,316
2,26
5,0
43,096
1,43
3
18,759
1,28
3a
19,759 19,625
40
a
14
4,5
30,552
1,72
6,0
47,204
42
15
4,5
32,340
1,79
5,5
47,881
1,33
3a
45
16
4,5
35,552
1,73
5,5
51,035
1,33
4a
26,793
47
17
4,5
37,365
1,78
5,5
52,974
1,36
4
26,659
48
18
4,5
38,387
2,07
5,0
53,156
1,47
4a
26,026
50
18
4,5
40,552
1,73
5,5
56,100
1,36
4
27,026
52
19
4,5
42,384
1,78
5,5
58,052
1,38
4
26,892 27,259
55
20
4,5
45,552
1,73
5,5
61,157
1,38
4a
58
22
4,5
48,424
1,99
5,0
63,198
1,51
4
26,491
60
22
4,5
50,552
1,73
5,5
66,206
1,40
5
34,293
62
23
4,5
52,413
1,77
5,0
66,846
1,45
5
34,159
65
24
4,5
55,552
1,73
5,0
69,924
1,44
5
34,526
68
26
4,5
58,448
1,94
5,0
73,229
1,53
5
33,759
70
26
4,5
60,552
1,73
5,0
74,954
1,46
5a
34,759
72
27
4,5
62,434
1,77
5,0
76,920
1,48
5a
34,625
75
28
4,5
65,552
1,73
5,0
79,980
1,47
6
41,793 41,026
78
30
4,5
68,464
1,90
5,0
83,253
1,55
6a
80
30
4,5
70,552
1,73
5,0
85,004
1,48
6
42,026
82
31
4,5
72,449
1,76
5,0
86,978
1,50
6
41,892
85
32
4,5
75,552
1,73
5,0
90,026
1,49
6a
42,259
88
34
4,5
78,476
1,88
5,0
93,272
1,57
6
41,491
90
34
4,5
80,552
1,73
5,0
95,045
1,50
7
49,293
92
35
4,5
82,461
1,76
5,0
97,024
1,52
7
49,159
95
36
4,5
85,552
1,73
5,0
100,063
1,51
7
49,526
98
38
4,5
88,485
1,86
5,0
103,288
1,58
7
48,759
100
38
4,5
90,552
1,73
5,0
105,079
1,52
7a
49,759
105
40
4,5
95,552
1,73
5,0
110,094
1,53
8
56,793
110
42
4,5
100,552
1,73
5,0
115,108
1,54
8
57,026
120
46
4,5
110,552
1,73
5,0
125,132
1,55
9
64,293
130
50
4,5
120,552
1,73
5,0
135,153
1,56
9a
64,759
140
54
4,5
130,552
1,73
5,0
145,172
1,57
10
72,026
150
58
4,5
140,552
1,73
5,0
155,188
1,58
11
79,293
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
27
DIN 5480-2:2006-05
14 Module m = 3 mm Table 22 — Nominal dimensions,
m =
3 mm
Dimensions in mm Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
Base diameter
d B
z
d
d b
22 25 28 30 32 35 37 38 40 42 45 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 210
6 7 8 8 9 10 11 11 12 12 13 14 a 14 14 15 16 17 18 18 19 20 21 22 22 24 24 25 26 27 28 28 29 30 31 32 34 35 38 42 45 48 52 55 58 62 65 68 69
18 21 24 24 27 30 33 33 36 36 39 42 42 42 45 48 51 54 54 57 60 63 66 66 72 72 75 78 81 84 84 87 90 93 96 102 105 114 126 135 144 156 165 174 186 195 204 207
15,588 18,187 20,785 20,785 23,383 25,981 28,579 28,579 31,177 31,177 33,775 36,373 36,373 36,373 38,971 41,569 44,167 46,765 46,765 49,363 51,962 54,560 57,158 57,158 62,354 62,354 64,952 67,550 70,148 72,746 72,746 75,344 77,942 80,540 83,138 88,335 90,933 98,727 109,119 116,913 124,708 135,100 142,894 150,688 161,081 168,875 176,669 179,267
a
28
Shaft Space width addendum Tooth modification thickness
Hub diameter Root diameter
Deviation
Root form circle diameter d Ff2
Shaft diameter Tip diameter
Tip diameter
Root form circle diameter d Ff1
Root Deviation diameter
⋅m
e2 = s1
d f2
Adf2
min.
d a2
d a1
max.
d f1
Adf1
0,35 0,35 0,35 1,35 0,85 0,85 0,35 0,85 0,35 1,35 1,35 –0,15 0,85 1,35 0,85 0,35 0,35 0,35 1,35 0,85 0,85 0,85 0,35 1,35 –0,15 1,35 0,85 0,35 0,35 0,35 1,35 0,85 0,85 0,85 0,35 –0,15 0,85 1,35 0,35 0,85 1,35 0,35 0,85 1,35 0,35 0,85 1,35 –0,15
5,117 5,117 5,117 6,271 5,694 5,694 5,117 5,694 5,117 6,271 6,271 4,539 5,694 6,271 5,694 5,117 5,117 5,117 6,271 5,694 5,694 5,694 5,117 6,271 4,539 6,271 5,694 5,117 5,117 5,117 6,271 5,694 5,694 5,694 5,117 4,539 5,694 6,271 5,117 5,694 6,271 5,117 5,694 6,271 5,117 5,694 6,271 4,539
22 25 28 30 32 35 37 38 40 42 45 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 210
0,71 0,71 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,72 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,74 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,76 0,77 0,77
21,46 24,46 27,47 29,47 31,47 34,47 36,47 37,47 39,47 41,47 44,47 44,47 46,47 47,47 49,47 51,48 54,48 57,48 59,48 61,48 64,48 67,48 69,48 71,48 74,48 77,48 79,48 81,48 84,48 87,48 89,48 91,48 94,48 97,48 99,48 104,49 109,49 119,49 129,49 139,49 149,49 159,49 169,49 179,49 189,49 199,49 209,50 209,50
16 19 22 24 26 29 31 32 34 36 39 39 41 42 44 46 49 52 54 56 59 62 64 66 69 72 74 76 79 82 84 86 89 92 94 99 104 114 124 134 144 154 164 174 184 194 204 204
21,4 24,4 27,4 29,4 31,4 34,4 36,4 37,4 39,4 41,4 44,4 44,4 46,4 47,4 49,4 51,4 54,4 57,4 59,4 61,4 64,4 67,4 69,4 71,4 74,4 77,4 79,4 81,4 84,4 87,4 89,4 91,4 94,4 97,4 99,4 104,4 109,4 119,4 129,4 139,4 149,4 159,4 169,4 179,4 189,4 199,4 209,4 209,4
15,94 18,94 21,93 23,93 25,93 28,93 30,93 31,93 33,93 35,93 38,93 38,93 40,93 41,93 43,93 45,92 48,92 51,92 53,92 55,92 58,92 61,92 63,92 65,92 68,92 71,92 73,92 75,92 78,92 81,92 83,92 85,92 88,92 91,92 93,92 98,91 103,91 113,91 123,91 133,91 143,91 153,91 163,91 173,91 183,91 193,91 203,90 203,90
15,40 18,40 21,40 23,40 25,40 28,40 30,40 31,40 33,40 35,40 38,40 38,40 40,40 41,40 43,40 45,40 48,40 51,40 53,40 55,40 58,40 61,40 63,40 65,40 68,40 71,40 73,40 75,40 78,40 81,40 83,40 85,40 88,40 91,40 93,40 98,40 103,40 113,40 123,40 133,40 143,40 153,40 163,40 173,40 183,40 193,40 203,40 203,40
–0,99 –0,99 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,03 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,09 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,15 –1,22 –1,22
x1
A special tool is required for manufacturing splined hubs by shaping.
DIN 5480-2:2006-05
Table 23 — Inspection dimensions,
m =
3 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions Number of Nominal teeth dimension measured
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
d B
z
DM
M 2
A*M2
DM
M 1
A*M1
k
W k
22 25 28 30 32 35 37 38 40 42 45 45 47 48 50 52 55 58 60 62 65 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 210
6 7 8 8 9 10 11 11 12 12 13 14 14 14 15 16 17 18 18 19 20 21 22 22 24 24 25 26 27 28 28 29 30 31 32 34 35 38 42 45 48 52 55 58 62 65 68 69
5,0 5,0 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,25 5,5 5,5 5,5 5,5 5,5 5,5 5,5
11,694 14,235 16,835 19,104 20,686 24,089 25,627 26,762 28,964 31,107 33,820 33,726 36,096 37,108 38,855 41,010 43,807 47,023 49,109 50,908 54,101 56,928 59,042 61,109 63,932 67,109 68,957 71,054 73,922 77,059 79,110 80,978 84,105 86,987 89,066 93,994 99,001 109,110 119,078 129,026 139,111 148,315 158,283 168,362 178,323 188,295 198,362 198,232
2,42 2,18 2,56 1,66 1,85 1,86 2,14 1,83 2,10 1,68 1,67 2,41 1,82 1,69 1,80 1,97 1,95 1,94 1,70 1,79 1,79 1,78 1,89 1,70 2,00 1,71 1,78 1,86 1,85 1,85 1,71 1,77 1,77 1,77 1,83 1,90 1,76 1,72 1,81 1,76 1,72 1,81 1,77 1,74 1,80 1,76 1,74 1,82
7,0 7,0 7,0 8,0 7,0 7,0 6,0 7,0 6,0 7,0 7,0 6,0 6,0 7,0 6,0 6,0 6,0 6,0 7,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0 6,0
30,099 32,544 36,289 40,013 39,577 43,158 42,581 45,828 45,989 50,023 52,752 51,216 52,848 56,148 55,606 58,088 60,873 64,125 68,343 67,767 70,999 73,827 76,183 77,868 81,326 83,909 85,923 88,227 91,092 94,245 95,977 97,995 101,141 104,025 106,275 111,380 116,076 126,095 136,329 146,167 156,172 166,364 176,228 186,226 196,389 206,272 216,266 216,400
1,17 1,17 1,23 1,14 1,21 1,25 1,35 1,25 1,38 1,26 1,26 1,46 1,37 1,29 1,38 1,44 1,44 1,46 1,34 1,43 1,44 1,45 1,49 1,43 1,54 1,44 1,48 1,52 1,52 1,53 1,47 1,50 1,51 1,51 1,55 1,59 1,53 1,52 1,58 1,57 1,55 1,61 1,59 1,58 1,62 1,61 1,60 1,65
2a 2 2 2a 2a 2a 2a 3a 3 3 3 3 3 3a 3a 3 3a 4 4 4 4 4a 4 5 4a 5 5 5 5 5a 6 6 6 6 6 6 7 7a 8 8a 9 9a 10 11 11 12 12 a 12
13,431 13,571 13,710 14,710 14,350 14,490 14,129 22,791 22,431 23,431 23,571 22,210 23,210 23,710 23,350 22,990 23,129 31,431 32,431 32,071 32,210 32,350 31,990 41,152 31,769 41,431 41,071 40,710 40,850 40,990 50,152 49,791 49,931 50,071 49,710 49,490 58,791 59,710 67,431 68,350 77,431 76,990 86,071 95,152 94,710 103,791 104,710 103,350
a
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
29
DIN 5480-2:2006-05
15 Module
m =
4 mm Table 24 — Nominal dimensions,
m =
4 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
z
d
d b
32 35 37 38 40 42 45 47 48 50 52 55 58 60 60 62 65 68 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210
6 7 8 8 8 9 10 10 10 11 11 12 13 a 13 14 14 15 15 a 16 16 16 17 18 18 19 20 20 21 22 22 23 24 25 26 28 31 34 36 38 41 44 46 48 51
24 28 32 32 32 36 40 40 40 44 44 48 52 52 56 56 60 60 64 64 64 68 72 72 76 80 80 84 88 88 92 96 100 104 112 124 136 144 152 164 176 184 192 204
20,785 24,249 27,713 27,713 27,713 31,177 34,641 34,641 34,641 38,105 38,105 41,569 45,033 45,033 48,497 48,497 51,962 51,962 55,426 55,426 55,426 58,890 62,354 62,354 65,818 69,282 69,282 72,746 76,210 76,210 79,674 83,138 86,603 90,067 96,995 107,387 117,779 124,708 131,636 142,028 152,420 159,349 166,277 176,669
a
30
Shaft diameter
Space width Tooth thickness
Root diameter
Deviation
Root form circle diameter d Ff2
Tip diameter
Tip diameter
Root form circle diameter d Ff1
⋅m
e2 = s1
d f2
Adf2
min.
d a2
d a1
max.
1,8 1,3 0,3 0,8 1,8 0,8 0,3 1,3 1,8 0,8 1,8 1,3 0,8 1,8 –0,2 0,8 0,3 1,8 –0,2 0,8 1,8 1,3 0,8 1,8 0,8 0,3 1,8 0,8 –0,2 1,3 0,8 –0,2 0,3 0,8 1,8 0,8 –0,2 0,8 1,8 0,8 –0,2 0,8 1,8 0,8
8,362 7,784 6,630 7,207 8,362 7,207 6,630 7,784 8,362 7,207 8,362 7,784 7,207 8,362 6,052 7,207 6,630 8,362 6,052 7,207 8,362 7,784 7,207 8,362 7,207 6,630 8,362 7,207 6,052 7,784 7,207 6,052 6,630 7,207 8,362 7,207 6,052 7,207 8,362 7,207 6,052 7,207 8,362 7,207
32 35 37 38 40 42 45 47 48 50 52 55 58 60 60 62 65 68 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210
0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,92 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,94 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,96 0,97
31,27 34,27 36,27 37,27 39,27 41,27 44,27 46,27 47,27 49,27 51,28 54,28 57,28 59,28 59,28 61,28 64,28 67,28 67,28 69,28 71,28 74,28 77,28 79,28 81,28 84,28 87,28 89,28 91,28 94,28 97,28 99,28 104,29 109,29 119,29 129,29 139,29 149,29 159,29 169,29 179,29 189,29 199,29 209,30
Shaft addendum Base diameter modification
d B
Hub diameter
x1
A special tool is required for manufacturing splined hubs by shaping.
24 27 29 30 32 34 37 39 40 42 44 47 50 52 52 54 57 60 60 62 64 67 70 72 74 77 80 82 84 87 90 92 97 102 112 122 132 142 152 162 172 182 192 202
31,2 34,2 36,2 37,2 39,2 41,2 44,2 46,2 47,2 49,2 51,2 54,2 57,2 59,2 59,2 61,2 64,2 67,2 67,2 69,2 71,2 74,2 77,2 79,2 81,2 84,2 87,2 89,2 91,2 94,2 97,2 99,2 104,2 109,2 119,2 129,2 139,2 149,2 159,2 169,2 179,2 189,2 199,2 209,2
23,93 26,93 28,93 29,93 31,93 33,93 36,93 38,93 39,93 41,93 43,92 46,92 49,92 51,92 51,92 53,92 56,92 59,92 59,92 61,92 63,92 66,92 69,92 71,92 73,92 76,92 79,92 81,92 83,92 86,92 89,92 91,92 96,91 101,91 111,91 121,91 131,91 141,91 151,91 161,91 171,91 181,91 191,91 201,90
Root Deviation diameter d f1
23,20 26,20 28,20 29,20 31,20 33,20 36,20 38,20 39,20 41,20 43,20 46,20 49,20 51,20 51,20 53,20 56,20 59,20 59,20 61,20 63,20 66,20 69,20 71,20 73,20 76,20 79,20 81,20 83,20 86,20 89,20 91,20 96,20 101,20 111,20 121,20 131,20 141,20 151,20 161,20 171,20 181,20 191,20 201,20
Adf1
–1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,23 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,29 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,35 –1,42
DIN 5480-2:2006-05
Table 25 — Inspection dimensions,
m =
4 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension
d B
z
DM
M 2
A*M2
DM
M 1
A*M1
k
W k
32 35 37 38 40 42 45 47 48 50 52 55 58 60 60 62 65 68 68 70 72 75 78 80 82 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210
6 7 8 8 8 9 10 10 10 11 11 12 13 13 14 14 15 15 16 16 16 17 18 18 19 20 20 21 22 22 23 24 25 26 28 31 34 36 38 41 44 46 48 51
7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,0 7,5 7,0
17,470 19,778 21,913 23,337 25,473 26,837 30,113 32,472 33,475 34,955 37,023 40,474 43,037 45,094 44,967 47,411 49,965 53,146 53,066 55,421 57,478 60,189 63,429 65,478 67,178 70,340 73,479 75,207 77,215 80,478 83,231 85,243 90,181 95,447 105,480 115,296 125,325 135,457 145,481 155,341 165,365 175,463 183,981 195,369
1,64 1,80 3,04 2,13 1,66 2,03 2,41 1,81 1,67 1,96 1,66 1,79 1,91 1,67 2,41 1,91 2,05 1,68 2,25 1,88 1,69 1,77 1,86 1,70 1,85 1,95 1,70 1,84 2,04 1,76 1,83 2,00 1,89 1,82 1,71 1,80 1,90 1,79 1,72 1,78 1,85 1,78 1,75 1,77
15 11 9,0 10 12 9,0 8,0 10 10 9,0 10 9,0 8,0 10 8,0 8,0 8,0 9,0 8,0 8,0 9,0 9,0 8,0 9,0 8,0 8,0 9,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0 8,0
54,521 48,316 47,335 50,447 56,413 51,497 52,967 59,393 60,090 59,797 63,660 65,139 65,470 71,967 68,288 69,932 72,791 77,722 76,329 78,001 82,163 85,115 86,058 90,273 89,803 93,257 98,368 97,877 100,414 102,993 105,939 108,435 113,123 118,217 127,969 138,115 148,507 158,332 168,127 178,247 188,549 198,404 208,229 218,331
1,02 1,09 1,25 1,19 1,11 1,23 1,36 1,21 1,20 1,28 1,21 1,29 1,37 1,24 1,46 1,39 1,43 1,31 1,48 1,42 1,33 1,35 1,44 1,35 1,44 1,49 1,37 1,46 1,53 1,45 1,48 1,54 1,52 1,50 1,47 1,53 1,59 1,55 1,52 1,57 1,62 1,58 1,55 1,59
2 2 2 2 2a 2 2 2a 3a 3a 3 3 3 3 3 3 3 3a 3 3a 4a 4 4 4 4 4 4a 4 4 5a 5a 4a 5 5 6 6 6 7 7a 8a 8 8a 9 9
19,241 18,928 18,114 18,614 19,614 18,800 18,486 19,486 30,869 30,055 31,055 30,741 30,428 31,428 29,614 30,614 30,300 31,800 29,986 30,986 42,869 42,555 42,241 43,241 42,428 42,114 43,614 42,800 41,986 54,369 54,055 42,359 53,928 54,614 66,869 66,428 65,986 78,241 79,614 90,055 89,614 90,986 103,241 102,800
a
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
31
DIN 5480-2:2006-05
16 Module
m =
5 mm Table 26 — Nominal dimensions,
m =
5 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
Base diameter
d
z
d
d
40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 75 78 80 82 85 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320
6 7 7 8 8 8 9 9 10 10 11 11 12 12 13 13 14 a 14 14 15 15 16 a 16 16 17 18 18 18 20 20 22 24 26 28 30 32 34 36 38 40 42 46 48 50 54 58 62
30 35 35 40 40 40 45 45 50 50 55 55 60 60 65 65 70 70 70 75 75 80 80 80 85 90 90 90 100 100 110 120 130 140 150 160 170 180 190 200 210 230 240 250 270 290 310
25,981 30,311 30,311 34,641 34,641 34,641 38,971 38,971 43,301 43,301 47,631 47,631 51,962 51,962 56,292 56,292 60,622 60,622 60,622 64,952 64,952 69,282 69,282 69,282 73,612 77,942 77,942 77,942 86,603 86,603 95,263 103,923 112,583 121,244 129,904 138,564 147,224 155,885 164,545 173,205 181,865 199,186 207,846 216,506 233,827 251,147 268,468
B
a
32
b
Shaft Space width addendum Tooth modification thickness x
1
⋅m
2,25 0,75 2,25 0,75 1,25 2,25 0,75 2,25 1,25 2,25 0,75 2,25 1,25 2,25 0,75 2,25 –0,25 1,25 2,25 0,75 2,25 –0,25 1,25 2,25 0,75 –0,25 1,25 2,25 –0,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25 2,25
e
2 = s1
10,452 8,720 10,452 8,720 9,297 10,452 8,720 10,452 9,297 10,452 8,720 10,452 9,297 10,452 8,720 10,452 7,565 9,297 10,452 8,720 10,452 7,565 9,297 10,452 8,720 7,565 9,297 10,452 7,565 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452 10,452
Hub diameter Root diameter d
f2
40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 75 78 80 82 85 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320
Deviation A
df2
1,14 1,14 1,14 1,14 1,14 1,14 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,16 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,17 1,19 1,19 1,19 1,19 1,19 1,19 1,19 1,19
A special tool is required for manufacturing splined hubs by shaping.
Root form circle diameter d Ff2
min. 39,08 41,08 44,08 46,08 47,08 49,08 51,09 54,09 57,09 59,09 61,09 64,09 67,09 69,09 71,09 74,09 74,09 77,09 79,09 81,09 84,09 84,09 87,09 89,09 91,09 94,09 97,09 99,09 104,10 109,10 119,10 129,10 139,10 149,10 159,10 169,10 179,10 189,10 199,10 209,11 219,11 239,11 249,11 259,11 279,11 299,11 319,11
Shaft diameter Tip diameter
Tip diameter
Root form circle diameter d Ff1
d
d
a1
max.
30 32 35 37 38 40 42 45 48 50 52 55 58 60 62 65 65 68 70 72 75 75 78 80 82 85 88 90 95 100 110 120 130 140 150 160 170 180 190 200 210 230 240 250 270 290 310
39 41 44 46 47 49 51 54 57 59 61 64 67 69 71 74 74 77 79 81 84 84 87 89 91 94 97 99 104 109 119 129 139 149 159 169 179 189 199 209 219 239 249 259 279 299 319
29,92 31,92 34,92 36,92 37,92 39,92 41,91 44,91 47,91 49,91 51,91 54,91 57,91 59,91 61,91 64,91 64,91 67,91 69,91 71,91 74,91 74,91 77,91 79,91 81,91 84,91 87,91 89,91 94,90 99,90 109,90 119,90 129,90 139,90 149,90 159,90 169,90 179,90 189,90 199,89 209,89 229,89 239,89 249,89 269,89 289,89 309,89
a2
Root Deviation diameter d
f1
29,00 31,00 34,00 36,00 37,00 39,00 41,00 44,00 47,00 49,00 51,00 54,00 57,00 59,00 61,00 64,00 64,00 67,00 69,00 71,00 74,00 74,00 77,00 79,00 81,00 84,00 87,00 89,00 94,00 99,00 109,00 119,00 129,00 139,00 149,00 159,00 169,00 179,00 189,00 199,00 209,00 229,00 239,00 249,00 269,00 289,00 309,00
A
df1
–1,49 –1,49 –1,49 –1,49 –1,49 –1,49 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,55 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,62 –1,70 –1,70 –1,70 –1,70 –1,70 –1,70 –1,70 –1,70
DIN 5480-2:2006-05
Table 27 — Inspection dimensions,
m =
5 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions Number of Nominal teeth dimension measured
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
d B
z
DM
M 2
A*M2
DM
M 1
A*M1
k
W k
40 42 45 47 48 50 52 55 58 60 62 65 68 70 72 75 75 78 80 82 85 85 88 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320
6 7 7 8 8 8 9 9 10 10 11 11 12 12 13 13 14 14 14 15 15 16 16 16 17 18 18 18 20 20 22 24 26 28 30 32 34 36 38 40 42 46 48 50 54 58 62
9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0 9,0
21,103 21,573 25,223 27,554 28,922 31,103 32,028 35,418 38,968 41,103 42,254 45,542 48,996 51,103 52,398 55,629 55,235 59,014 61,103 62,498 65,692 65,416 69,027 71,103 72,573 75,531 79,036 81,103 85,613 91,103 101,103 111,103 121,103 131,103 141,103 151,103 161,103 171,103 181,103 191,103 201,103 221,103 231,103 241,103 261,103 281,103 301,103
1,71 3,29 1,67 2,71 2,13 1,72 2,41 1,69 2,01 1,72 2,19 1,70 1,95 1,72 2,08 1,71 2,62 1,91 1,72 2,01 1,72 2,37 1,88 1,73 1,96 2,24 1,86 1,73 2,15 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73
18 12 16 12 12 14 11 14 12 14 11 12 11 12 10 12 10 11 12 10 12 10 10 11 10 10 10 11 10 11 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
66,516 55,246 66,185 61,519 62,214 68,226 63,404 72,552 72,502 78,660 73,752 78,376 80,236 84,186 81,440 88,738 85,360 90,386 94,408 91,603 99,025 95,411 97,908 102,069 101,731 105,453 107,987 112,200 115,488 122,313 129,780 139,848 149,908 159,961 170,009 180,051 190,090 200,126 210,158 220,188 230,215 250,264 260,286 270,307 290,343 310,376 330,405
1,03 1,16 1,04 1,21 1,20 1,13 1,25 1,13 1,24 1,17 1,30 1,22 1,31 1,25 1,38 1,25 1,46 1,34 1,28 1,41 1,29 1,48 1,41 1,33 1,43 1,50 1,43 1,36 1,52 1,38 1,43 1,44 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,55 1,55 1,56 1,57 1,58 1,59
2 2 2 2 2 2a 2 2a 2a 3a 2a 3 3 3 3 3 3 3 3a 3 3a 3 3a 4a 3a 3a 4 4 4 4a 5 5 5a 6 6 6a 7 7 7a 8 8 9 9 9a 10 11 11 a
24,052 22,784 24,284 23,017 23,517 24,517 23,250 24,750 23,983 38,586 23,716 38,819 38,052 39,052 37,784 39,284 37,017 38,517 39,517 38,250 39,750 37,483 38,983 53,586 38,716 37,948 53,052 54,052 52,017 54,517 68,586 69,052 69,517 83,586 84,052 84,517 98,586 99,052 99,517 113,586 114,052 128,586 129,052 129,517 144,052 158,586 159,517
a
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
33
DIN 5480-2:2006-05
17 Module
m =
6 mm Table 28 — Nominal dimensions,
m =
6 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
Base diameter
d B
z
d
d b
48 50 52 55 58 60 62 65 68 70 72 75 78 78 80 82 85 88 90 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500
6 7 7 8 8 8 9 9 10 10 10 11 11 12 a 12 12 13 13 13 14 a 14 14 15 15 16 17 18 20 22 24 25 27 28 30 32 34 35 38 40 42 45 48 52 55 58 62 65 68 72 74 75 78 82
36 42 42 48 48 48 54 54 60 60 60 66 66 72 72 72 78 78 78 84 84 84 90 90 96 102 108 120 132 144 150 162 168 180 192 204 210 228 240 252 270 288 312 330 348 372 390 408 432 444 450 468 492
31,177 36,373 36,373 41,569 41,569 41,569 46,765 46,765 51,962 51,962 51,962 57,158 57,158 62,354 62,354 62,354 67,550 67,550 67,550 72,746 72,746 72,746 77,942 77,942 83,138 88,335 93,531 103,923 114,315 124,708 129,904 140,296 145,492 155,885 166,277 176,669 181,865 197,454 207,846 218,238 233,827 249,415 270,200 285,788 301,377 322,161 337,750 353,338 374,123 384,515 389,711 405,300 426,084
a
34
⋅m
2,7 0,7 1,7 0,2 1,7 2,7 0,7 2,2 0,7 1,7 2,7 1,2 2,7 –0,3 0,7 1,7 0,2 1,7 2,7 –0,3 0,7 2,2 0,7 1,7 1,2 0,7 2,7 1,7 0,7 –0,3 1,7 0,7 2,7 1,7 0,7 –0,3 1,7 2,7 1,7 0,7 1,7 0,7 0,7 1,7 2,7 0,7 1,7 2,7 0,7 –0,3 1,7 2,7 0,7
Shaft diameter
Root diameter
Deviation
Root form circle diameter d Ff2
Tip diameter
Tip diameter
Root form circle diameter d Ff1
Root diameter
Deviation
e2 = s1
d f2
Adf2
min.
d a2
d a1
max.
d f1
Adf1
12,542 10,233 11,388 9,656 11,388 12,542 10,233 11,965 10,233 11,388 12,542 10,810 12,542 9,078 10,233 11,388 9,656 11,388 12,542 9,078 10,233 11,965 10,233 11,388 10,810 10,233 12,542 11,388 10,233 9,078 11,388 10,233 12,542 11,388 10,233 9,078 11,388 12,542 11,388 10,233 11,388 10,233 10,233 11,388 12,542 10,233 11,388 12,542 10,233 9,078 11,388 12,542 10,233
48 50 52 55 58 60 62 65 68 70 72 75 78 78 80 82 85 88 90 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 296 320 340 360 380 400 420 440 450 460 480 500
1,34 1,34 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,36 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,37 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,39 1,42 1,42 1,42 1,42 1,42 1,42
46,88 48,88 50,89 53,89 56,89 58,89 60,89 63,89 66,89 68,89 70,89 73,89 76,89 76,89 78,89 80,89 83,89 86,89 88,89 88,89 90,89 93,89 96,89 98,89 103,90 108,90 118,90 128,90 138,90 148,90 158,90 168,90 178,90 188,90 198,90 208,91 218,91 238,91 248,91 258,91 278,91 294,91 318,91 338,91 358,91 378,91 398,91 418,93 438,93 448,93 458,93 478,93 498,93
36 38 40 43 46 48 50 53 56 58 60 63 66 66 68 70 73 76 78 78 80 83 86 88 93 98 108 118 128 138 148 158 168 178 188 198 208 228 238 248 268 284 308 328 348 368 388 408 428 438 448 468 488
46,8 48,8 50,8 53,8 56,8 58,8 60,8 63,8 66,8 68,8 70,8 73,8 76,8 76,8 78,8 80,8 83,8 86,8 88,8 88,8 90,8 93,8 96,8 98,8 103,8 108,8 118,8 128,8 138,8 148,8 158,8 168,8 178,8 188,8 198,8 208,8 218,8 238,8 248,8 258,8 278,8 294,8 318,8 338,8 358,8 378,8 398,8 418,8 438,8 448,8 458,8 478,8 498,8
35,92 37,92 39,91 42,91 45,91 47,91 49,91 52,91 55,91 57,91 59,91 62,91 65,91 65,91 67,91 69,91 72,91 75,91 77,91 77,91 79,91 82,91 85,91 87,91 92,90 97,90 107,90 117,90 127,90 137,90 147,90 157,90 167,90 177,90 187,90 197,89 207,89 227,89 237,89 247,89 267,89 283,89 307,89 327,89 347,89 367,89 387,89 407,87 427,87 437,87 447,87 467,87 487,87
Shaft Space width addendum Tooth modification thickness x1
Hub diameter
A special tool is required for manufacturing splined hubs by shaping.
34,80 36,80 38,80 41,80 44,80 46,80 48,80 51,80 54,80 56,80 58,80 61,80 64,80 64,80 66,80 68,80 71,80 74,80 76,80 76,80 78,80 81,80 84,80 86,80 91,80 96,80 106,80 116,80 126,80 136,80 146,80 156,80 166,80 176,80 186,80 196,80 206,80 226,80 236,80 246,80 266,80 282,80 306,80 326,80 346,80 366,80 386,80 406,80 426,80 436,80 446,80 466,80 486,80
–1,69 –1,69 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,75 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,82 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,90 –1,98 –1,98 –1,98 –1,98 –1,98 –1,98
DIN 5480-2:2006-05
Table 29 — Inspection dimensions,
m =
6 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
d B
z
DM
M 2
A *M2
DM
48 50 52 55 58 60 62 65 68 70 72 75 78 78 80 82 85 88 90 90 92 95 98 100 105 110 120 130 140 150 160 170 180 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500
6 7 7 8 8 8 9 9 10 10 10 11 11 12 12 12 13 13 13 14 14 14 15 15 16 17 18 20 22 24 25 27 28 30 32 34 35 38 40 42 45 48 52 55 58 62 65 68 72 74 75 78 82
10,5 10 10,5 10 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 10,5 11 11 11 11 11 11 11 11 11 11 11
26,204 28,471 29,136 34,169 36,165 38,209 39,007 42,406 45,839 48,178 50,212 52,433 55,534 55,200 57,928 60,187 62,185 65,631 67,641 67,451 69,982 73,223 75,529 77,709 83,132 87,614 98,217 108,203 118,084 127,864 137,914 147,845 158,220 168,210 178,132 187,988 198,002 218,221 228,214 238,156 258,051 278,221 296,630 316,566 336,724 356,646 376,590 396,724 416,657 426,581 436,608 456,724 476,666
1,64 2,18 1,89 2,56 1,91 1,66 2,32 1,73 2,24 1,86 1,67 1,96 1,66 2,75 2,10 1,84 2,23 1,82 1,67 2,41 2,02 1,75 1,99 1,80 1,88 1,95 1,70 1,79 1,89 2,00 1,78 1,85 1,71 1,77 1,83 1,90 1,76 1,72 1,76 1,81 1,76 1,72 1,81 1,77 1,74 1,80 1,76 1,74 1,79 1,81 1,76 1,74 1,78
22 14 16 12 16 18 14 16 14 14 16 14 15 12 12 14 12 14 14 12 12 14 12 12 12 12 14 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 11 11 11 11 11 11 11 11 11 11 11
a
Deviation factor
Number of teeth measured
Nominal dimension
M 1
A *M1
k
W k
80,692 65,089 71,023 66,901 78,701 84,619 77,745 84,551 84,861 86,315 92,509 90,930 95,491 90,355 91,978 98,580 96,601 104,032 105,505 102,431 104,088 111,549 109,597 111,211 117,001 121,745 136,686 141,997 152,367 162,653 171,846 182,184 191,953 202,282 212,550 222,760 232,152 252,190 262,447 272,658 292,335 312,343 329,859 349,607 369,617 389,891 409,675 429,677 449,915 459,993 469,725 489,723 509,933
1,02 1,17 1,10 1,33 1,16 1,11 1,23 1,15 1,27 1,25 1,18 1,27 1,21 1,43 1,38 1,28 1,41 1,29 1,26 1,46 1,41 1,30 1,42 1,38 1,42 1,44 1,34 1,44 1,49 1,54 1,48 1,52 1,47 1,51 1,55 1,59 1,53 1,52 1,55 1,58 1,57 1,55 1,63 1,61 1,60 1,65 1,63 1,61 1,66 1,68 1,64 1,63 1,66
2 2 2 2 2 2 2 2 2 2 3 3 3 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 5 5 6 6 6 6 7 7 7 8 8 9 9 10 11 11 12 12 13 13 13 14 14
Measuring circle Nominal diameter dimension
a
a
a a a
a
a a a
a
a a
a
a
a
a
a
28,862 27,141 28,141 26,921 28,421 29,421 27,700 29,200 27,979 28,979 46,303 45,083 46,583 27,538 44,862 45,862 44,641 46,141 47,141 44,421 45,421 46,921 45,700 46,700 46,479 46,259 64,862 64,421 63,979 63,538 82,141 81,700 100,303 99,862 99,421 98,979 117,583 119,421 118,979 134,862 136,700 154,862 153,979 172,141 190,303 189,421 207,583 209,421 224,862 224,421 226,700 244,862 243,979
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other a tooth thickness measurements not identified by .
35
DIN 5480-2:2006-05
18 Module m = 8 mm Table 30 — Nominal dimensions,
m =
8 mm Dimensions in mm
Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
Base diameter
Deviation
Root form circle diameter d Ff2
Tip diameter
Tip diameter
Root form circle diameter d Ff1
Root diameter
Deviation
e2 = s1
d f2
Adf2
min.
d a2
d a1
max.
d f1
Adf1
d B
z
d
d b
60
6
48
41,569
1,6
14,414
60
1,76
58,49
44
58,4
43,91
42,40
–2,15
65
7
56
48,497
0,1
12,682
65
1,76
63,49
49
63,4
48,91
47,40
–2,15
70
7
56
48,497
2,6
15,569
70
1,76
68,49
54
68,4
53,91
52,40
–2,15
75
8
64
55,426
1,1
13,837
75
1,76
73,49
59
73,4
58,91
57,40
–2,15
80
8
64
55,426
3,6
16,723
80
1,76
78,49
64
78,4
63,91
62,40
–2,15
85
9
72
62,354
2,1
14,991
85
1,76
83,49
69
83,4
68,91
67,40
–2,15
90
10
80
69,282
0,6
13,259
90
1,76
88,49
74
88,4
73,91
72,40
–2,15
95
10
80
69,282
3,1
16,146
95
1,76
93,49
79
93,4
78,91
77,40
–2,15
100
11
88
76,210
1,6
14,414
100
1,76
98,49
84
98,4
83,91
82,40
–2,15
105
12
96
83,138
0,1
12,682
105
1,77
103,50
89
103,4
88,90
87,40
–2,22
110
12
96
83,138
2,6
15,569
110
1,77
108,50
94
108,4
93,90
92,40
–2,22
120
13
104
90,067
3,6
16,723
120
1,77
118,50
104
118,4
103,90
102,40
–2,22
112
96,995
–0,4
12,104
120
1,77
118,50
104
118,4
103,90
102,40
–2,22
120
14
a
⋅m
Shaft diameter
Root diameter
Shaft Space width addendum Tooth modification thickness x1
Hub diameter
130
15
120
103,923
0,6
13,259
130
1,77
128,50
114
128,4
113,90
112,40
–2,22
140
16
128
110,851
1,6
14,414
140
1,77
138,50
124
138,4
123,90
122,40
–2,22
150
17
136
117,779
2,6
15,569
150
1,77
148,50
134
148,4
133,90
132,40
–2,22
160
18
144
124,708
3,6
16,723
160
1,77
158,50
144
158,4
143,90
142,40
–2,22
170
20
160
138,564
0,6
13,259
170
1,77
168,50
154
168,4
153,90
152,40
–2,22
180
21
168
145,492
1,6
14,414
180
1,77
178,50
164
178,4
163,90
162,40
–2,22
190
22
176
152,420
2,6
15,569
190
1,77
188,50
174
188,4
173,90
172,40
–2,22
200
24
192
166,277
–0,4
12,104
200
1,77
198,50
184
198,4
183,90
182,40
–2,22
210
25
200
173,205
0,6
13,259
210
1,79
208,51
194
208,4
193,89
192,40
–2,30
220
26
208
180,133
1,6
14,414
220
1,79
218,51
204
218,4
203,89
202,40
–2,30
240
28
224
193,990
3,6
16,723
240
1,79
238,51
224
238,4
223,89
222,40
–2,30
250
30
240
207,846
0,6
13,259
250
1,79
248,51
234
248,4
233,89
232,40
–2,30
260
31
248
214,774
1,6
14,414
260
1,79
258,51
244
258,4
243,89
242,40
–2,30
280
34
272
235,559
–0,4
12,104
280
1,79
278,51
264
278,4
263,89
262,40
–2,30
300
36
288
249,415
1,6
14,414
300
1,79
298,51
284
298,4
283,89
282,40
–2,30
320
38
304
263,272
3,6
16,723
320
1,79
318,51
304
318,4
303,89
302,40
–2,30
340
41
328
284,056
1,6
14,414
340
1,79
338,51
324
338,4
323,89
322,40
–2,30
360
44
352
304,841
–0,4
12,104
360
1,79
358,51
344
358,4
343,89
342,40
–2,30
380
46
368
318,697
1,6
14,414
380
1,79
378,51
364
378,4
363,89
362,40
–2,30
400
48
384
332,554
3,6
16,723
400
1,79
398,51
384
398,4
383,89
382,40
–2,30
420
51
408
353,338
1,6
14,414
420
1,82
418,53
404
418,4
403,87
402,40
–2,38
440
54
432
374,123
–0,4
12,104
440
1,82
438,53
424
438,4
423,87
422,40
–2,38
450
55
440
381,051
0,6
13,259
450
1,82
448,53
434
448,4
433,87
432,40
–2,38
460
56
448
387,979
1,6
14,414
460
1,82
458,53
444
458,4
443,87
442,40
–2,38
480
58
464
401,836
3,6
16,723
480
1,82
478,53
464
478,4
463,87
462,40
–2,38
500
61
488
422,620
1,6
14,414
500
1,82
498,53
484
498,4
483,87
482,40
–2,38
a
36
A special tool is required for manufacturing splined hubs by shaping.
DIN 5480-2:2006-05
Table 31 — Inspection dimensions,
m =
8 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions Number of Nominal teeth dimension measured
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
d B
z
DM
M 2
A *M2
DM
M 1
A *M1
60
6
14
30,516
2,42
22
88,848
1,11
2
36,483
65
7
13b
36,924
2,63
16
79,195
1,27
2
35,355
70
7
14
39,557
1,80
22
96,632
1,09
2
37,855
75
8
14
45,371
2,42
18
95,390
1,24
2
36,728
80
8
14
50,945
1,66
22
108,241
1,13
2a
39,228
85
9
14
54,803
1,89
20
108,481
1,18
2
38,100
90
10
14
60,225
2,41
16
105,933
1,36
2
36,972
1,21
3a
61,238
1,28
3a
60,110 58,983
95 100
10 11
14 14
65,966 69,911
1,73 1,96
20 18
119,486 119,594
k
W k
105
12
14
75,080
2,41
16
121,294
1,41
3a
110
12
14
80,948
1,79
18
130,279
1,29
3
61,483
120
13
14
90,188
1,67
20
143,934
1,24
3
62,855
120
14
14
89,935
2,41
16
136,575
1,46
3
59,228
130
15
14
99,929
2,05
16
145,582
1,43
3
60,600
140
16
14
110,843
1,88
16
156,001
1,42
3a
61,972
150
17
14
120,378
1,77
18
170,231
1,35
4
85,110
160
18
14
130,956
1,70
18
180,546
1,35
4
86,483
170
20
14
140,681
1,95
16
186,514
1,49
4
84,228
180
21
14
150,414
1,84
16
195,753
1,46
4
85,600
190
22
14
160,956
1,76
16
205,987
1,45
5a
108,738
200
24
14
170,486
2,00
16
216,870
1,54
4a
84,717
210
25
14
180,363
1,89
16
226,246
1,52
5
107,855
220
26
14
190,894
1,82
16
236,435
1,50
5
109,228
240
28
14
210,959
1,71
16
255,937
1,47
6
133,738
250
30
14
220,788
1,86
16
266,768
1,55
6
131,483
260
31
14
230,592
1,80
16
276,230
1,53
6
132,855
280
34
14
250,650
1,90
16
297,014
1,59
6
131,972
300
36
14
270,915
1,79
16
316,665
1,55
7
156,483
320
38
14
290,961
1,72
16
336,253
1,52
7a
159,228
340
41
14
310,683
1,78
16
356,494
1,57
8a
180,110
360
44
14
330,731
1,85
16
377,099
1,62
8
179,228 181,972
380
46
14
350,926
1,78
16
396,808
1,58
8a
400
48
14
370,962
1,72
16
416,458
1,55
9
206,483
420
51
14
390,738
1,77
16
436,662
1,59
9
205,600
440
54
14
410,778
1,83
16
457,155
1,63
9a
204,717
450
55
14
420,697
1,80
16
466,855
1,62
10
227,855
460
56
14
430,934
1,77
16
476,906
1,60
10
229,228
480
58
14
450,963
1,72
16
496,602
1,58
11
253,738
500
61
14
470,776
1,77
16
516,779
1,61
11
252,855
a
These tooth thickness measurements are not reliable because they were made near the root fillet or the edge of the tip. Measurements between and over measuring circles are preferable. Deviations and tolerances can result in the unreliability of other tooth thickness measurements not identified by a.
b
Not specified in DIN 3977.
37
DIN 5480-2:2006-05
19 Module
m =
10 mm Table 32 — Nominal dimensions, m = 10 mm Dimensions in mm Nominal dimensions
Basic data ReferNumence ber of diameter teeth
Pitch diameter
Base diameter
Shaft Space width addendum Tooth modification thickness
⋅m
Shaft diameter
Deviation
Root form circle diameter d Ff2
Tip diameter
Tip diameter
Root form circle diameter d Ff1
d f2
Adf2
min.
d a2
d a1
max.
Root diameter
e2 = s1
Root Deviation diameter
d B
z
d
d b
80
6
60
51,962
4,5
20,904
80
2,16
78,09
60
78
59,91
58,00
–2,55
85
7
70
60,622
2
18,017
85
2,16
83,09
65
83
64,91
63,00
–2,55
90
7
70
60,622
4,5
20,904
90
2,16
88,09
70
88
69,91
68,00
–2,55
95
8
80
69,282
2
18,017
95
2,16
93,09
75
93
74,91
73,00
–2,55
100
8
80
69,282
4,5
20,904
100
2,16
98,09
80
98
79,91
78,00
–2,55
105
9
90
77,942
2
18,017
105
2,17
103,10
85
103
84,90
83,00
–2,62
110
9
90
77,942
4,5
20,904
110
2,17
108,10
90
108
89,90
88,00
–2,62
120
10
100
86,603
4,5
20,904
120
2,17
118,10
100
118
99,90
98,00
–2,62
130
11
110
95,263
4,5
20,904
130
2,17
128,10
110
128
109,90
108,00
–2,62
120
103,923
–0,5
15,131
130
2,17
128,10
110
128
109,90
108,00
–2,62
a
x1
Hub diameter
d f1
Adf1
130
12
140
12
120
103,923
4,5
20,904
140
2,17
138,10
120
138
119,90
118,00
–2,62
150
13
130
112,583
4,5
20,904
150
2,17
148,10
130
148
129,90
128,00
–2,62
140
121,244
–0,5
15,131
150
2,17
148,10
130
148
129,90
128,00
–2,62
a
150
14
160
14
140
121,244
4,5
20,904
160
2,17
158,10
140
158
139,90
138,00
–2,62
170
15
150
129,904
4,5
20,904
170
2,17
168,10
150
168
149,90
148,00
–2,62
160
138,564
–0,5
15,131
170
2,17
168,10
150
168
149,90
148,00
–2,62
a
170
16
180
16
160
138,564
4,5
20,904
180
2,17
178,10
160
178
159,90
158,00
–2,62
190
17
170
147,224
4,5
20,904
190
2,17
188,10
170
188
169,90
168,00
–2,62
180
155,885
–0,5
15,131
190
2,17
188,10
170
188
169,90
168,00
–2,62
180
155,885
4,5
20,904
200
2,17
198,10
180
198
179,90
178,00
–2,62
200
173,205
–0,5
15,131
210
2,19
208,11
190
208
189,89
188,00
–2,70
a
190
18
200
18 a
210
20
220
20
200
173,205
4,5
20,904
220
2,19
218,11
200
218
199,89
198,00
–2,70
240
22
220
190,526
4,5
20,904
240
2,19
238,11
220
238
219,89
218,00
–2,70
250
24
240
207,846
–0,5
15,131
250
2,19
248,11
230
248
229,89
228,00
–2,70
260
24
240
207,846
4,5
20,904
260
2,19
258,11
240
258
239,89
238,00
–2,70
280
26
260
225,167
4,5
20,904
280
2,19
278,11
260
278
259,89
258,00
–2,70
300
28
280
242,487
4,5
20,904
300
2,19
298,11
280
298
279,89
278,00
–2,70
320
30
300
259,808
4,5
20,904
320
2,19
318,11
300
318
299,89
298,00
–2,70
340
32
320
277,128
4,5
20,904
340
2,19
338,11
320
338
319,89
318,00
–2,70
360
34
340
294,449
4,5
20,904
360
2,19
358,11
340
358
339,89
338,00
–2,70
380
36
360
311,769
4,5
20,904
380
2,19
378,11
360
378
359,89
358,00
–2,70
400
38
380
329,090
4,5
20,904
400
2,19
398,11
380
398
379,89
378,00
–2,70
420
40
400
346,410
4,5
20,904
420
2,22
418,13
400
418
399,87
398,00
–2,78
440
42
420
363,731
4,5
20,904
440
2,22
438,13
420
438
419,87
418,00
–2,78
450
44
440
381,051
–0,5
15,131
450
2,22
448,13
430
448
429,87
428,00
–2,78
460
44
440
381,051
4,5
20,904
460
2,22
458,13
440
458
439,87
438,00
–2,78
480
46
460
398,372
4,5
20,904
480
2,22
478,13
460
478
459,87
458,00
–2,78
500
48
480
415,692
4,5
20,904
500
2,22
498,13
480
498
479,87
478,00
–2,78
a
38
A special tool is required for manufacturing splined hubs by shaping.
DIN 5480-2:2006-05
Table 33 — Inspection dimensions,
m =
10 mm Dimensions in mm
Basic data
Hub dimensions
Shaft dimensions
Reference diameter
Number of teeth
Measuring circle diameter
Nominal dimension
Deviation factor
Measuring circle diameter
Nominal dimension
Deviation factor
Number of teeth measured
Nominal dimension
d B
z
DM
M 2
A *M2
DM
M 1
A *M1
k
W k
80 85 90 95 100 105 110 120 130 130 140 150 150 160 170 170 180 190 190 200 210 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500
6 7 7 8 8 9 9 10 11 12 12 13 14 14 15 16 16 17 18 18 20 20 22 24 24 26 28 30 32 34 36 38 40 42 44 44 46 48
18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18
42,206 44,776 50,446 56,557 62,206 65,378 70,836 82,206 91,085 89,781 102,206 111,257 110,470 122,207 131,384 130,832 142,207 151,481 151,063 162,207 171,225 182,207 202,207 211,440 222,207 242,207 262,207 282,207 302,207 322,207 342,207 362,207 382,207 402,207 411,838 422,207 442,207 462,207
1,71 2,50 1,67 2,34 1,72 2,18 1,69 1,72 1,70 3,27 1,72 1,71 2,62 1,72 1,72 2,37 1,73 1,72 2,24 1,73 2,15 1,73 1,73 2,04 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,73 1,87 1,73 1,73 1,73
35 25 30 25 28 25 28 25 25 22 25 25 22 25 22 22 22 22 20 22 20 22 22 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20
130,845 113,476 127,942 126,117 136,452 134,743 145,104 150,225 159,151 155,828 170,806 179,918 176,022 191,284 193,049 196,180 204,139 213,455 210,905 224,401 230,976 244,626 264,823 271,088 279,696 299,816 319,922 340,017 360,103 380,181 400,252 420,316 440,376 460,431 471,373 480,481 500,528 520,572
1,03 1,13 1,06 1,19 1,13 1,19 1,13 1,20 1,21 1,37 1,23 1,24 1,40 1,27 1,31 1,43 1,33 1,34 1,50 1,36 1,52 1,38 1,40 1,54 1,44 1,46 1,47 1,48 1,49 1,50 1,51 1,52 1,53 1,54 1,62 1,54 1,55 1,55
2 2 2 2 2a 2 2a 3a 3 2a 3 3 3 3a 3a 3 4a 4 3a 4 4 4a 5 4a 5 5a 6 6 6a 7 7 7a 8 8 8 8a 9 9
48,103 46,069 48,569 46,534 49,034 47,000 49,500 77,172 77,638 45,897 78,103 78,569 74,034 79,034 79,500 74,966 107,172 107,638 75,897 108,103 104,034 109,034 137,172 105,897 138,103 139,034 167,172 168,103 169,034 197,172 198,103 199,034 227,172 228,103 224,034 229,034 257,172 258,103
a
The deviation values stated here relate to chip-cutting machining methods and the theoretical root diameter (see DIN 5480-1, 7.1). The deviation for cold-rolled splines is –0,76 ⋅ m.
39
View more...
Comments
