3D-07-13F1-132_SP3D Operator Training Guide _Lab5 Grid Task_EN_Rev0_WATERMARK
March 29, 2017 | Author: anton hidayat | Category: N/A
Short Description
TRAINING...
Description
Job Code Doc. No.
6-1720-10-0000 3D-07-13F1-132
SP3D Operator Training Guide
Lab5: Grids Task Training
3D ENGINEERING PROPULSION GROUP
REV 0
DATE 01/May/’09
REASON FOR ISSUE 1st Issue
PREP’D D.Iwata
CHK’D T.Hayami
APR’D T.Hayami
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
1 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
Lab5: Grid Task Training 1
OUTLINE .......................................................................................................................................................... 3 1.1
2
CREATE THE STD GRID ................................................................................................................................ 4 2.1
3
Grid Task ................................................................................................................................................... 3
Create the Grid for Structure ..................................................................................................................... 4
CREATE RADIAL GRID ................................................................................................................................ 12 3.1
Create Grid for Vertical Vessel ................................................................................................................ 12
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
2 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
1
OUTLINE
1.1
Grid Task
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
Grids Task is used to place Grid Planes and Grid Lines for placing structures and platforms in the model. Placing the structures on gridlines creates a relationship between the structure and the gridline. This relationship automatically adjusts the length of the structure when you edit the gridlines. In this training, you will place the general STD Grid Line for Structure and Radial Grid for vertical vessels.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
3 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
2
CREATE THE STD GRID
2.1
Create the Grid for Structure
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
Create the Grid for 090-PRK-0013 Structure in this section.
(1) Click File > Define Workspace and choose the filter”2.1 STD Grid”.
(2) Set to “Civil” for Active Permission, and set to “WBS_Project" for Active WBS.
(3) Click Tasks > Grids
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
4 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
(4) Click Grid Wizard
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
command from toolbar.
(5) Grid Wizard will be displayed. Set the parameter to the following.
Name Axis for bearing Bearing Reference CS East(X) North(Y) Up(Z)
(6)
Click
Next>
091-PRK-0013_CS North (Y) N 0.00 deg E Global 171.5 m 25.5 m 0m
button.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
5 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(7) Set the parameters for the first Elevation with the following:
1st Column Reference CS
091-PRK-0013_CS
Start Plane
16.9 m
Copies Spacing
0 Ignore
End plane
16.9 m
Name rule
Position
Nesting Level
Primary
Type
Bottom Of Concrete
Please select ‘Primary’ to display Grid line on the Drawing, and if not, please select ‘Secondary’ for ‘Nesting Level’.
(8) Click Add button. Elevation Plane of EL16.9 is added in the list.
(9) Set the parameters for the second Elevation with the following:
2nd Column Reference CS
091-PRK-0013_CS
Start Plane
22.4 m
Copies
0
Spacing
Ignore
End plane
22.4 m
Name rule
Position
Nesting Level
Primary
Type
Top Of Concrete
(10) Click Add button. Elevation Plane of EL22.4 is added in the list.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
6 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(11) Add the third Elevation Plane (EL25.4 m) and fourth Elevation Plane (EL27.9 m) in the same way. Set the parameters as follows.
3rd Column
4th Column
Reference CS
091-PRK-0013_CS
091-PRK-0013_CS
Start Plane
25.4 m
27.9 m
Copies
0
0
Spacing
Ignore
Ignore
End plane
25.4 m
27.9 m
Name rule
Position
Position
Nesting Level
Primary
Primary
Type
Top Of Concrete
Top Of Concrete
(12) Make sure that the four Elevation Planes are listed then click
Next >
button.
(13) Next, create the Grid Plane in the X direction. Set the parameters as follows. Create the two lines at the same time by using “Copies” and “Spacing”
Reference CS
091-PRK-0013_CS
Start Plane
0m
Copies
1
Spacing
6.0 m
End plane
6.0 m
Name rule
User Defined
Nesting Level
Primary
Type
E-W Grid Plane
(14) Click
Add
button and then 0m and 6m X-planes will be added in the list.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
7 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(15) Double-click and input the name in the Name columns.
Double Click (16) Click
Next >
button.
(17) Create the Grid line in the Y direction. Set the parameter as follows. In this step, create the five lines at the same time by using “Copies” and “Spacing” functions.
Reference CS
091-PRK-001_CS
Start Plane
0m
Copies
4
Spacing
9.0 m
End plane
36.0 m
Name rule
Alphanumeric and Percent
Nesting Level
Primary
Type
N-S Grid Plane
(18) Click
Add
(19) Click
Next >
button and then Plane is added in the list.
button.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
8 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(20) Create Radial Cylinder menu will be displayed, no setting is needed, go on to the next.
(21) Create Radial Plane menu will be displayed and click the
Next >
button.
(22) At the end, click Finish button. Make sure that all Elevation Planes are in the “Selected elevation planes” window.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
9 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(23) Coordinate System, Grid Lines and Rulers are displayed in the model, and Coordinate System and Plane are added to Workspace Explorer. Ruler Grid Line Coordinate System
Plane
Ruler Ruler Coordinate System
(24) To hide rulers, Click View > Rulers… (25) Press and hold down the Ctrl button. The Rulers will be hidden.
Key and click 091-PRK-0013_CS and then click
OK
(26) “091-PRK-0013_CS” is not set on the correct Hierarchy in the Workspace Explorer. To set the Hierarchy, change the Locate Filter to the Coordinate System.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
10 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(27) Select “091-PRK-0013_CS” from the Workspace Explore. The “Edit Coordinate System Ribbon Bar” will be displayed.
(28) From the System list box, select “More…”, and move to 091-PRK-0013 Structure System.
(29) Click OK button and finish the dialog box. Make sure that Hierarchy of Coordinate System is changed on the Workspace Explorer.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
11 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
3
CREATE RADIAL GRID
3.1
Create Grid for Vertical Vessel
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
When you input an arc-shaped platform, you need to create a Radial Grid to use as boundaries for the platform creation.
(1) Click File > Define Workspace and set the filter to “3.1 Radial Grid”.
(2) Set to “Civil” for Active Permission, and set to “WBS_Project" for Active WBS.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
12 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
(3) Click Grid Wizard
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
command from toolbar.
(4) Grid Wizard dialog box is displayed. Set the parameters as follows.
Name Axis for bearing Bearing Reference CS East(X) North(Y) Up(Z)
(5) Click
Next >
041-D-1002_CS North (Y) N 0.00 deg E Global 166.5 m 27.5 m 0m
button.
(6) Set the parameters to create Elevation Plane as follows.
1st Column
2nd Column
3rd Column
Reference CS
041-D-1002_CS
041-D-1002_CS
041-D-1002_CS
Start Plane
15.85 m
21.0 m
25.0 m
Copies
0
0
0
Spacing
Ignore
Ignore
Ignore
End plane
15.85 m
21.0 m
25.0 m
Name rule
Position
Position
Position
Nesting Level
Primary
Primary
Primary
Type
Bottom Of Baseplate
Top Of Steel
Top Of Steel
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
13 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
(7) Click
Next >
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
button.
(8) Create [Grid X-Plane wizard] is displayed. Click
Next >
(9) The [Create Grid Y-Plane] window is displayed. Click
button without any settings.
Next >
button.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
14 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(10) In the Create Radial Cylinder, set the parameter as follows. Create 2 Radial Cylinders at 0.7m and 2.2m.
1st Column
2nd Column
Reference CS
041-D-1002_CS
041-D-1002_CS
Start Cylinder
0.7 m
2.2 m
Copies
0
0
Spacing
Ignore
Ignore
End Cylinder
0.7 m
2.2 m
Name rule
Position
Position
Nesting Level
Primary
Primary
Type
Undefined
Undefined
(11) Click
Next >
button.
(12) In the Create a Radial Plane, set the parameters as follows. Create 4 Radial Planes by 45 degrees increments using “Copies” and “Spacing” at the same time.
Reference CS
041-D-1002_CS
Start Plane
0 deg
Copies
3
Spacing
45.0 deg
End plane
135.0 deg
Name rule
Position
Nesting Level
Primary
Type
Undefined
(13) Click
Add >
button. The Planes are added in the list.
(14) Click
Next >
button.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
15 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
(15) At the end, Click
Finish >
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
button to finish the Grid Wizard.
(16) Coordinate System, Grid Line and Rulers are created in the model. Coordinate System and Planes will be added in Workspace Explorer.
Coordinate System
Plane
Grid Line
Ruler
Coordinate System
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
16 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(17) Click View > Rulers… and open the Ruler dialog box. (18) Press and hold down the to remove the Rulers.
Ctrl
Key and click 041-D-1002_CS and then click
OK
button
(19) To set 041-D-1002_CS to the correct Hierarchy, select the Coordinate System in Locate Filter.
(20) Select 041-D-1002_CS on Workspace Explorer, the [Edit Coordinate System Ribbon Bar] will be displayed.
(21) Select [More…] from System list box, and select the 041-D-1002 to move under the equipment hierarchy.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
17 of 18
3D ENGINEERING PROPULSION GROUP SP3D Operator Training Guide
Job Code: Doc. No.:
6-1720-10-0000 3D-07-13F1-132
(22) Click OK button and make sure that Coordinate System of hierarchy is under the Equipment on Workspace Explorer.
3D-07-13F1-132_SP3D Operator Training Guide (Lab5 Grid Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved
18 of 18
View more...
Comments