335-Dot

8

6

7

5

4

2

3

1 REVISION HISTORY REV 2

H

119 32 7 8 3 4

Ø212 112

G

121

481

N/R

H

123 32 0.900 1 R116

12th Fret Girth: 3.11 Waist: 5.15

9 16

R78

Overlay 1st and 12th Fret

G

1st Fret Girth: 2.73 Waist: 4.45

238

Epi length (19th fret)

7 (2 plcs) Ø16

Headstock ear (2 plcs)

12.281

341

4

Neck Heel Detail

10MAY2011

1.000

Ø12 (2 plcs)

Ø12 (4 plcs) 7 Tap 6-32 (2 plcs) Ø64

225 32

N/A

5 Min. 64 0.023 Wide Fret Slot

Blend (binding) edge 1 216

Ø312

CHECKED

11 116 Maple Filler

Ø83 (12 plcs)

DATE

1 4

R12

Neck Binding 0.020 x 0.250 x 18 (2 plcs + end)

INCORP BY

Added strap button and grounding wire holes.

3 (10 plcs) Ø32

5 16

211 16

DESCRIPTION

7 116

229 32

2.1035 in

1.50

1.75

F

F 1/4" MOP Dot (10 plcs)

19 132

1.375 Ø23 64 (6 plcs) for Kluson TPKR3-N

Ø18 (GND)

Ø38 7 in Ø16

NOTES:

1 1 1 1. Top and back plates' plies are maple, basswood (cross-grain), and maple (16, 10, 16). 1 2. Rim plies are 16 maple, basswood (cross-grain), and maple.

Ø11 32 in (4 plcs)

E

E

3. Top view shows fret board, headstock, pickguard in fabricated planes to reflect their true size. 4. Add material to create a smooth surface using elevations shown in laminate template. 5. F-holes and control layout for use with a pin router. 1 3 6. Neck is quarter-sawn mahogany (blank 2 2 (fretboard surface) x 2 4 (parallel to grain) x 26).

Kerfing - 7/32 x 9/16 x 31 (4 plcs)

D

143 3 16

7. Kerfing is mahogany, spruce, or basswood.

Binding - 0.060 x 0.250 x 62 (2 plcs) Spruce - Kerf 0.025, 1/4 Centers (2 plcs)

8. Girth - to edges of playing surface. Waist - girth and playing surface perimeter.

D

0.447

0.225 3 4

Maple Centerblock

24.687 Nut to Treble Post 24.625 5 116 3 (2 plcs) Ø32

88°

5 116

1 Spruce Stock 2

94°0'

1.000

112

4°0'

17°

0.900

R141

Truss Rod Channel 0.250 wide, 0.400 deep (dependent on truss rod used) Cover with maple filler strip.

5 16

Mahogany Tailblock

C

3 16

1

R6

0.060 Holly Veneer

Jig Indexing Pins (6 plcs)

1814

C 5 8

1 116

*+,#+ ' () #+ *- .-

B

B 8.0

$

! " # % " #&

UNLESS OTHERWISE SPECIFIED DIM ARE IN INCHES TOL ON ANGLE ± 0° 30' .XX ± .03 .XXX ± .010 INTERPRET DIM AND TOL PER ASME Y14.5M - 1994 DO NOT SCALE DRAWING

Curve Length 30.57

THIRD ANGLE PROJECTION

A

TITLE

335 / DOT CONSTRUCTION Copyright (c) 2010 by Pat Sharkey. This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivs 3.0 Unported License. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc-nd/3.0/ or send a letter to Creative Commons, 171 Second Street, Suite 300, San Francisco, California, 94105, USA. SIZE

REV

E SCALE

8

7

6

5

4

3

2

A 2

1:1

SHEET

1

1 of 1