Comments MIMO changed for 4x2 as Claro CO requested. ASIB introduction, introduction, GSM under under review
Claro Cla ro Pla Plane neaci ación ón / No Nokia kia Ra Radio dio
Target configuratio configurations ns for 2020 deployment and extra configurations for 2nd nodes. Targett con Targe config figur urati ation ons s for 20 2020 20 de deplo ployme yment, nt, tra transp nsport ort de detai tails ls an and d 3rd optional config.
BASE BAND Current Configurations: WCDMA/LTE 1900 RF Sharing with LTE 2600 FSMF Airscale base band • •
BAND: 850MHz LTE/WCDMA Current Curr ent conf configur iguration ation 1
2
3
c e s
c e s
c e s
LTE
LTE
LTE
WCDMA
WCDMA
WCDMA
W 1: 1: 1T 1T x& x& 2R 2R x
W 2: 2: 1T 1T x& x& 2R 2R x
W 3: 3: 1T 1T x& x& 2R 2R x
W 1: 1: 1T 1T x& x& 2R 2R x
FXCB/A (FRM 3TX6RX B5)
W 2: 2: 1T 1T x& x& 2R 2R x
W 3: 3: 1T 1T x& x& 2R 2R x
FXCB/A (FRM 3TX6RX B5)
W 1: 1: 1T 1T x& x& 2R 2R x
850MHz
Comments RADIO Current Configuration: FXCB/A RF module 3TX/6RX Optional NB-IoT in Airscale • •
W 2: 2: 1T 1T x& x& 2R 2R x
W 3: 3: 1T 1T x& x& 2R 2R x
FXCB/A (FRM 3TX6RX B5)
3xFXCB/A (B5) 3G 2/2/2 @10MHz 1T2R 20W
BASE BAND Current Configuration: FSMF OR Airscale for new sites. •
FSMF +2FBBx System Module
FSMF
OR
Airscale base band Airscale System Module
ADDITIONAL COMMENTS COMMENTS: Optio Optional nal LTE with NB-IoT wher where e base baseband band and RF modul module e pipes pipes availa available ble..
3G 850: 2+2+2+2+2 2+2+2 +2+2 WCDMA* *Traffic *Traff ic est estima imatio tion n is nee needed ded in orde orderr to ev eval alua uate te th the e #users, #user s, check check Note 1. 1.
L 700MHz
LTE (2T/4R) 1+1+1 @20W
Notes 1.
4° - 6°
In ca case se WCD WCDMA MA85 850 0 req requi uire ress ext extra ra ca capa paci city ty,, a separate FSMF can be considered for 4 to 6 extra sectors
The main synchronization came from network Timing over Packet (Frequency), and chained base bands receive Phase/SyncE Synchronization from main source.
FBBC: SRAN
•
Optional
2nd Nodes
•
SynE feature SRAN18SP SRAN18SP SR000844/LTE563 Synchronous Ethernet Generation needed. SRAN is not supported in IRU networks without 4G Hub, as VLAN can not mapped. Max throughput need to be considered in TX dimensioning. 5G expansion TX and Synch need a direct source. Required min two (2) ToP sessions for Required each base band. In case of FSMF for 1900, it requires one additional additional ToP session for the the first in the chain. The synchronization after this FSMF SRAN must be through of HDMI cable. The main synchronization came from network Timing over Packet (Frequency), and chained base bands receive Phase/SyncE Synchronization from main source Max length for HDMI Synchronizat Synchronization ion cables 15m. Chaining HDMI and Fibers are 2m length
The main synchronization came from network Timing over Packet (Frequency), and chained base bands receive Phase/SyncE Synchronization from main source.
FBBC: SRAN
•
Optional
2nd Nodes
•
SynE feature SRAN18SP SRAN18SP SR000844/LTE563 Synchronous Ethernet Generation needed. SRAN is not supported in IRU networks without 4G Hub, as VLAN can not mapped. Max throughput need to be considered in TX dimensioning. 5G expansion TX and Synch need a direct source. Required min two (2) ToP sessions for Required each base band. In case of FSMF for 1900, it requires one additional additional ToP session for the the first in the chain. The synchronization after this FSMF SRAN must be through of HDMI cable. The main synchronization came from network Timing over Packet (Frequency), and chained base bands receive Phase/SyncE Synchronization from main source. Max length for HDMI Synchroniza Synchronization tion cables 15m. Chain Ch ainin ing g HDM HDMII and Fib Fiber erss are 2m leng length th
Thank you for interesting in our services. We are a non-profit group that run this website to share documents. We need your help to maintenance this website.