279215065 Kone Monospace Controller Manual Pt2 PDF

KONE MonoSpace® 3.0 Installation Instruction

KONE MONOSPACE®, RELEASE 3.0

1075531.wmf

KONEA) Installation (Draft AM-01.01.250 2012-08-28 MonoSpace® Instruction3.0

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Copyright ©2012 KONE Corporation All rights reserved.

No part of the contents of this document may be copied, reproduced or transmitted in any form or by any means, or translated into another language or format, in whole or part, without prior written permission of KONE Corporation. Authorization Notice This publication is for informational purposes only. All persons participating in the installation and/or maintenance of KONE equipment and using these instructions must be qualified to perform such work, are required to have received equipment specific training as specified by KONE and must have KONE Corporation's authorization to install and maintain KONE equipment. DISCLAIMER OF WARRANTIES AND LIABILITIES KONE reserves the right at any time to alter the product design, specifications and procedures reflected in this document. NO STATEMENT CONTAINED IN THIS DOCUMENT IS TO BE CONSTRUED AS A WARRANTY OR CONDITION, EXPRESS OR IMPLIED, AS TO ANY PRODUCT, SPECIFICATION OR PROCEDURE, ITS MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE OR QUALITY, OR AS A MODIFICATION OR REPRESENTATION OF THE TERMS OF ANY PURCHASE AGREEMENT. KONE DISCLAIMS ANY LIABILITY RESULTING FROM OR IN CONNECTION WITH THE USE OR DISCLOSURE OF INFORMATION IN THIS DOCUMENT. KONE HAS NO LIABILITY FOR TYPOGRAPHICAL OR OTHER ERRORS OR OMISSIONS CONTAINED IN THIS DOCUMENT OR ANYONE'S INTERPRETATION OF THE INSTRUCTIONS. THE USER OF THIS DOCUMENT ASSUMES ALL RISKS ASSOCIATED WITH THE USE OR DISCLOSURE OF THIS DOCUMENT. Confidentiality Notice This proprietary and confidential document is provided to you only for purposes of installing and/or maintaining KONE products and it may not be used or its contents disclosed for any other purpose without KONE's prior written permission. Neither this document nor its contents may be copied or disclosed to third parties for any reason. KONE reserves the right to prosecute any breach of this obligation. Trademark Notice "KONE, MonoSpace, MiniSpace, EcoDisc, TranSys, Alta, KoneXion, KONE ECO3000 and all other product names are trademarks or registered trademarks of KONE Corporation in various countries."

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

1 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

TABLE OF CONTENTS 1

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.1 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.2 Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.3 Daily installation order guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.4 Customer experience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 1.5 Explanation for quality requirement table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 General safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Recommended working postures and ergonomic methods . . . . . . . . . . . . . . . . . . . 2.3 Installation method safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Danger and personal protection signs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

SITE REQUIREMENTS AND TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 3.1 Site requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 3.2 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4

OFFLOADING AND DISTRIBUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.1 Offloading and distributing materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 4.2 Offloading and transporting landing doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5

INSTALLING MAN RIDING HOIST AND OVERSPEED GOVERNOR . . . . . . . . . . . . . . . . 5.1 Man riding hoist parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Work positioning equipment or restraint system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Safety checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 Routing the man riding hoist rope and cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6 Installing overspeed governor hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.7 Fixing the man riding hoist rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8 Lowering the man riding hoist hook to the pit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.9 Pit ladder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.10 Testing the hoist equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

PLUMBING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 6.1 Elevator shaft plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.2 Plumbing table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

7

MECHANICAL INSTALLATION IN THE PIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Guide rail preparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Installing dividing beams (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 Guide rail brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Installing first guide rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Installing and aligning the first length of car guide rails (TH £ 3500). . . . . . . . . . . . . 7.6 Installing counterweight buffer and OSG tension weight. . . . . . . . . . . . . . . . . . . . . . 7.7 Installing counterweight frame (without safety gear, primary method) . . . . . . . . . . .

20 20 24 25 27

42 43 45 46 46 47 48 49 50 50 51

55 56 58 59 60 63 64 65

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

2 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

7.8 7.9 7.10

Installing counterweight frame (without safety gear, alternative method) . . . . . . . . . 66 Installing counterweight frame with safety gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Installing car buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

8

CAR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 Installing uprights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Installing bottom beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Installing car floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 Connecting OSG and ASGT ropes to safety gear linkage. . . . . . . . . . . . . . . . . . . . . 8.5 Initial loading of counterweight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 Installing car walls (option 1, first customer pilots in Europe) . . . . . . . . . . . . . . . . . . 8.7 Installing car walls (option 2, after first customer pilots in Europe) . . . . . . . . . . . . . . 8.8 Installing car walls (through type car) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.9 Installing top beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10 Installing car top balustrade and car roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.11 Tensioning overspeed governor rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

70 71 73 76 78 79 80 81 82 83 84 87

9

ATTACHING HOIST TO CAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 Installing swivel balustrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Attaching hoist and automatic safety gear trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Testing ASGT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Using ASGT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

88 89 91 92 93

10

CAR INTERIOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 10.1 Installing ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 10.2 Mirrors and handrails. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 10.3 Skirting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 10.4 Installing seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 10.5 Installing buffer rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 10.6 Installing tenant directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

11

INSTALLING REST OF GUIDE RAILS AND BRACKETS . . . . . . . . . . . . . . . . . . . . . . . . . .112 11.1 Preparing for guide rail installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 11.2 Installing third ring of guide rail brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 11.3 Installing guide rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116

12

MECHANICAL INSTALLATION IN TOP OF ELEVATOR SHAFT . . . . . . . . . . . . . . . . . . . .117 12.1 Installing overspeed governor to final position . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 12.2 Installing counterweight overspeed governor and tension weight . . . . . . . . . . . . . . .119 12.3 Removing the extension rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 12.4 Car sill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 12.5 Installing machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 12.6 Parking plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 12.7 Installing rope hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 12.8 Filing and checking the guide rail joints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

3 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

13

LANDING DOOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 Installation order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2 Installing landing sill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 Installing uprights and top parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4 Installing door panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 Top track settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 Installing panels and strips (front type version only) . . . . . . . . . . . . . . . . . . . . . . . . 13.7 Installing landing toe guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

131 132 133 137 141 145 146 150

14

CAR FRONT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 14.1 Installing car front walls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 14.2 Finalizing car front installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

15

INSTALLING CAR DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1 Unpacking and transporting the door operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2 Installation of Low duty door operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3 Installation of Mid and High duty door operator. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4 Installing finger protection list (window / glass doors) . . . . . . . . . . . . . . . . . . . . . . . 15.5 Door panel buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6 Door panel fixings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 Door panel guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.8 Installation of door panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.9 Coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.10 Railing settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.11 Emergency opening for car door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12 Electrification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.13 Car door lock and contact measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

155 156 156 159 161 161 162 163 163 166 171 174 175 177

16

KONE SIGNALIZATION SYSTEM (KSS) INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 16.1 Hall indicator (KSH) and landing call station (KSL) . . . . . . . . . . . . . . . . . . . . . . . . . 16.2 Installing COP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.3 Hall display (KSJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

179 180 181 182

17

INSTALLING MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 17.1 Installing wall type MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 17.2 Installing door type MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

18

IDE300 (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

19

ELECTRIFICATION AT TOP OF THE ELEVATOR SHAFT (KDL16S) . . . . . . . . . . . . . . . 19.1 Overview (KDL16S). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2 Opening drive covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3 Installing SEP and drive panels, brake resistor and trunkings (KDL16S) . . . . . . . . 19.4 Connecting machine cables (KDL16S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5 Cabling: MAP - drive, SEP - drive (KDL16S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

ELECTRIFICATION AT TOP OF THE ELEVATOR SHAFT (KDM40) . . . . . . . . . . . . . . . . 195 20.1 Overview (KDM40) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197

187 189 190 191 193 194

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

4 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

20.2 20.3 20.4 20.5

Installing SEP and drive panels, KDA module, brake resistor and trunkings (KDM40)198 Machine cables (KDM40) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Cabling: MAP - KDA module, SEP - KDA module (KDM40) . . . . . . . . . . . . . . . . . . 201 Cabling: KDA - drive module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

21

CABLES: SEP-MAP, MAIN SUPPLY, KRM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.1 Installing load weighing sensor, OSG cables and topmost lighting unit . . . . . . . . . 21.2 Wiring between SEP and MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.3 Connecting main supply cable to MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.4 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.5 Group connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

203 204 205 206 206 208

22

INSTALLING TRAVELLING CABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 22.1 Installing travelling cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212

23

ELEVATOR SHAFT WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.1 Shaft lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.2 Installing shaft wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.3 Wiring at the landings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.4 Installing segmented shaft network (if 16 served floors / group elevator) . . . . . . . . 23.5 Installing support channel (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

213 214 215 216 217 218

24

ELECTRIFICATION IN THE PIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.1 Finalizing car installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.2 Installing electrification under the car . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.3 Installing pit electrification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.4 Installing pit toe guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

219 220 221 222 223

25

CAR ELECTRIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.1 Magnet switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.2 Installing car top connection box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.3 Installing electrification on the car roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.4 Install the provision for lift announcer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.5 Install the intercom socket on the car roof. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.6 Installing curtain of light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.7 Installing ramps and magnets (driving up). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.8 Wiring of door operator and curtain of light (or photo cell) . . . . . . . . . . . . . . . . . . .

224 225 226 228 229 229 230 235 236

26

FINALIZING LANDING DOORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.1 Uprights on slampost side (fire rated EI30/EI60/EI120-W doors) . . . . . . . . . . . . . . 26.2 Uprights on non-slampost side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.3 Fire trims (frame version only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.4 Corner angles and wall gaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.5 Top extension panel fire insulation (front version only) . . . . . . . . . . . . . . . . . . . . . . 26.6 Carpet profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.7 Quality check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

237 238 239 242 245 245 246 246

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

5 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27

ROPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.1 Lubrication of suspension ropes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.2 Roping principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.3 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.4 Roping in the pit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.5 Attaching compensation chain under the car (optional) . . . . . . . . . . . . . . . . . . . . . 27.6 Roping at top of the elevator shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.7 Shortening the ropes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.8 Attaching compensation chain to counterweight . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.9 Moving OSG rope in the large groove. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.10 Installing brake release cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.11 Testing manual brake release operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.12 Dismantling man riding hoist from car . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.13 Finalizing car installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

247 248 250 251 252 252 253 254 256 256 257 259 260 261

28

COMMISSIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28.2 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28.3 Final steps of commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28.4 Fine adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

262 263 265 266 267

29

COMMISSIONING OF THE CAR DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.1 Layout of drive 10 electronic assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.2 Layout of AMD drive 2 electronic assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.3 Testing factory adjusted door operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.4 Adjusting closing force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.5 LEDs, drive 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.6 DIP-switches, drive 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.7 LEDs, drive 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.8 DIP-switches, drive 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.9 Commissioning of curtain of light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

268 269 270 272 273 274 275 275 277 278

30

FINAL STEPS AND ELEVATOR SHAFT CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.1 Correction of parameter settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.2 Checking the levelling accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.3 Volume adjustment (audible feedback) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.4 Group locking function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.5 Emergency lighting battery and KONE remote monitoring . . . . . . . . . . . . . . . . . . . 30.6 Emergency battery drive (EBD-A) test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.7 Testing the compensation chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.8 Elevator shaft cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

280 281 281 282 282 283 284 285 285

31

SAFETY INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 31.1 Safety inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

6 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

32

HANDOVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32.2 Handover form. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32.3 Installation quality checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

287 287 287 289

33

FAULT FINDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.1 Fault finding procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.2 Normal run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.3 Faults in drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

294 294 294 296

34

APPROVALS AND VERSION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298

35

FEEDBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299

APPENDIX A. KDL drive related issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 APPENDIX B. Balancing factors and loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 APPENDIX D. Electrification panels, introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 APPENDIX E. Elevator shaft wiring with trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 APPENDIX G. Energy efficiency class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 APPENDIX H. Ceiling types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

7 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1

GENERAL The single and flexible man installation method described in this instruction is designed to ensure an efficient, trouble-free installation, whilst maintaining safe working practices. This is a general instruction which can be used for MonoSpace® release 3.0 elevators. Some of the components may differ from those that are described in this instruction. In these cases refer to the delivery documents or component level AM instructions. Follow this instruction. If it is necessary to deviate from the method a carefully designed, risk assessed, method statement must first be obtained from your front line management. All installation tasks must be controlled and verified during installation by filling in the completion sheet which is used as a checklist before: – commissioning – safety inspection – handover to maintenance and customer

1.1

Abbreviations

1.1.1

General

Abbreviation FFL CL DBG A B C D

Term finished floor level central line distance between guide rails marking of entrance e.g. A-door/side marking of entrance e.g. B-door/side marking of entrance e.g. C-door/side marking of entrance e.g. D-door/side

C2

Definition

usually main door, always MAP side opposite main door

C1

D2

B1

D1

B2 A

1078299.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

8 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1.1.2

Elevator shaft and car

Abbreviation Term elevator shaft SH headroom height

Unit

Definition

mm

PH

pit depth

mm

WW

elevator shaft width

mm

WD

elevator shaft depth

mm

H HF

travel height floor to floor distance

mm mm

the vertical distance between the finished floor at the highest level served and the roof of the elevator shaft that part of the elevator shaft located under the lowest landing level served by the elevator the horizontal distance between the inner surfaces of the elevator shaft walls measured parallel to the car width the horizontal distance between the inner surfaces of the elevator shaft walls measured parallel to the car depth sum of interfloor distances given as a minimum

car clear height car clear width car clear depth toe guard height

mm mm mm mm

car and landing door sills

car CH BB DD NE

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

9 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Elevator shaft vertical dimensions Front doors

HH

PH

PH

HH

HF

H

HA

HF

HR

H

HB

CH

HH

CH

SH

SH

HA HB HB

Frame doors

1007040.wmf

1007041.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

10 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1.1.3

Landing/front and frame door

Elevator shaft horizontal dimensions, front door

1007043.wmf

Abbreviation LW LW1 LW2 LD LR HR HA HB LL HH

Term from clear opening to elevator shaft wall from clear opening to elevator shaft wall from clear opening to elevator shaft wall side wall depth door raw opening width door raw opening height front door lintel height front door extension height door clear opening width door clear opening height

Unit mm mm mm mm mm mm mm mm mm mm

Definition

front door case LR=WW

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

11 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Elevator shaft horizontal dimensions, frame door

1007042.wmf

Abbreviation FW FW1 FW2 ? FD LR HR LL HH 1.1.4

Term front wall width front wall width front wall width front wall depth door raw opening width door raw opening height door clear opening width door clear opening height

Unit mm mm mm mm mm mm mm mm

Definition

FW2 does not exist here! LR=WW-2*FW or WW-(FW+FW1)

Additional abbreviations MAP = maintenance access panel SEP = shaft electrification panel

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

12 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1.2

Related documents In addition to this manual, you can find safety- and product-related information in the following documents: – AM-01.03.001 Preventing falls from height when working on elevators, escalators and building doors – AM-01.03.002 Take 5 - Electrical safety when working on elevators, escalators and autowalks – AM-01.03.003 Take 2 - double security safety practice when using hoists for man riding purposes – AM-01.03.010 Safe working in elevator shaft and machine room areas – AS-01.01.030 Rescue instruction for KONE MonoSpace type elevator – AS-12.02.001 Instruction for handling electrostatic-discharge-sensitive-devices on site – AM-01.01.190 Environmental excellence - Installation – AM-01.01.260 5S guide book - Eliminating unnecessary actions in elevator installation – AM-01.01.261 5S advanced instructions - Eliminating unnecessary actions in elevator installation – AM-01.05.016 Installing light entrance protection (LEP) – AM-03.12.067 Automatic car door AMDC – AM-03.12.094 KES201 landing door – AM-03.17.011 Formula systems slimscreen curtain of light FCU 0735 and FZU 1047 3D (for automatic car door AMD) – AM-03.35.020 Electrical installation, commissioning, troubleshooting instruction, AMD drive 2 + car door operator – AM-03.35.027 Electrical Installation, Commissioning and Troubleshooting Instruction AMD Drive 10 Car Door Operator – AM-03.90.121 ReNova slim landing door – AM-04.05.056 Hoisting Machine NMX07 / NMX11 – AM-06.06.030 Hermes Car – AM-06.12.010 Global accessories, suspended ceilings and lighting – AM-07.04.040 Progressive type safety gear AQ32 – AM-07.04.042 Progressive type safety gear CSGB-01 – AM-10.60.028 Elevator shaft bundle (cables and connection boxes without trunking) – AM-11.65.038 ECB-1 single line ReGenerative unit – AM-11.65.042 KDM drive for MonoSpace® and MonoSpace® Special: Installation, commissioning and safety inspection – AM-11.65.045 Machine-Room-Less Elevators with KDL16S drive, Installing, Commissioning and Safety Inspection – AM-12.20.005 KONE Signalisation System (KSS) installation – AM-12.20.017 KONE Polaris™ 500 and 800 Destination Control Systems (DCS) – AM-13.20.018 KONE IDE300™ - Integration of doors and elevator – AM-13.25.007 KONE remote monitoring (KRM) for elevators

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

13 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

– – – – – – – – – – – – –

994525D01 KDM Parameter list (delivered with drive) 994525D02 KDM Diagnostic Code List 994525D03 KDM Parameter Guide 972483D01 KDL16 Parameter Table (delivered with drive) 972484D01 KDL16 Parameter Guide 972485D01 KDL16 Diagnostic Codes 813138 Global LCE Fault Codes 813131 User Interface Menu Instructions for LCE 812281 F2K Remote Control Boards 818442 PIN Code Feature 827328 Configuration switch instruction Man riding hoist manual Shaft vane diagrams, layout drawings, wiring diagrams

Product-related maintenance instructions and spare parts lists: – AS-03.12.036 Maintenance instruction for AMD doors – AR-03.12.037 Spare parts manual for AMD car door – AR-03.12.076 Spare parts manual for AMD landing door – – – –

AS-03.12.036 Maintenance instruction for AMD doors ASG-03.12.036 Preventive maintenance instruction for AMD doors AR-03.12.037 Spare parts manual for AMD car door AR-03.12.076 Spare parts manual for AMD landing door

– AS-07.03.016 Repairing Hermes car sling – AS-04.08.039 Replacing the brakes of hoisting machines NMX07 and NMX11 – AR-04.06.016 Spare Parts NMX11 – AS-11.65.040 Repair instruction for KDM drive system in KONE MonoSpace Special – AR-11.65.040 Spare parts manual for KDM drive system – AS-11.65.052 Repairing KDL16S – AR-11.65.034 Spare parts manual for KDL16 drives – AS-10.22.006 Repair instruction for KONE MonoSpace®, MonoSpace® 1.6 m/s and TranSys™ shaft electrification panels – AR-10.22.006 Spare parts manual for KONE MonoSpace electrification

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

14 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1.3

Daily installation order guide

Elevator shaft Door type

Car interior

1.3.1

Elevator 5 floors, 12 m travel, single side entrances AMDL1 or AMDL2, frame non fire rated, installation with expander bolts for guide rails and landing doors One handrail and one mirror

Prerequisites to meet the schedule Complete on time / error free delivery Installation site fulfilling the 5 Site Absolutes Fitter has installed 5-8 units prior. Working within allocated working hours.

Single man schedule The table below indicates phases of the installation. Day 1

2

3

Action Arrival at site, transporting tools, receiving delivery. Installing man riding hoist, installing overspeed governor. Setting the lasers. Plumbing and establishing plumbing table. Installing first guide rail brackets and pit ladder, preparing counterweight frame. Installing and aligning first lengths of guide rails and brackets. Installing buffers and counterweight frame. Installing sling and installing overspeed governor. Installing car and initial loading of the counterweight. Waste material handling. Installing automatic safety gear trigger. Attaching man riding hoist to car and installing third ring of guide rail brackets. Installing car interior. Installing working light to the car roof. Installing and aligning guide rails and brackets to intermediate floors. Installing topmost floor lengths of guide rails and brackets. Transferring the overspeed governor to its final position and setting the rope to final length. Installing car sill. Installing machine and rope fixings. Installing landing door sill brackets.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

15 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Day 4

5

6

7

1.3.2

Action Installing landing doors, not finally adjusted. Installing car front wall and car door. Installing last landing door. Installing trunking and elevator shaft lighting. Waste material handling. Final adjustment of landing doors. Installing MAP, SEP and drive panels. Installing elevator shaft top wiring and brake lever. Installing travelling cables, elevator shaft wiring and signalization. Installing car wiring and setting positioning system and ramps. Installing pit wiring. Waste material handling. Installing car electrification and car operating panel. Placing filler weights inside the car for balancing operations, roping. Closing the brake, re-checking the brake lever operation, safety checks, commissioning and removal of tools. Balancing and final steps. Cleaning down the elevator shaft and disposal of waste materials. Safety inspection (assistance with test weights).

Flexible man schedule The table below indicates in which phases of the installation two men are required and when the installation can be undertaking by a single man. Day 1

Action Arrival at site, transporting tools, receiving delivery. Installing the man riding hoist, installing the overspeed governor. Setting the plumbing jig. Cleaning guide rails and mounting fish plates. Plumbing and establishing plumbing table. Installing first guide rail brackets and pit ladder, preparing counterweight frame. Installing and aligning first lengths of guide rails and brackets. Installing buffers and counterweight frame. Installing sling and installing overspeed governor for single man working.

Task split fitter 1 / 2 1 2 1 2 2 1 2 1 1

2

1

2

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

16 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Day 2

3

4

5

6

7

Action Installing the car and initial loading of the counterweight. Waste material handling. Installing the automatic safety gear trigger. Attaching the man riding hoist to car and installing the third ring of guide rail brackets. Installing the car interior. Installing and aligning guide rails and brackets to intermediate floors. Preparing the car and counterweight guide rail brackets. Preparing machine and landing door brackets Installing top most floor lengths of guide rails and brackets. Transferring the overspeed governor to final position and setting the rope to final length. Installing the pulley beam and car sill. Installing the machine and rope fixings. Installing the landing door sill brackets. Installing the trunking and elevator shaft lighting Installing the landing doors, not finally adjusted. Installing the car front wall and car door. Installing the last landing door. Waste material handling. Final adjustment of the landing doors. Installing the MAP, SEP and drive panels. Installing the elevator shaft top wiring and brake lever. Installing the travelling cables, shaft wiring and signalization. Installing car wiring and setting positioning system and ramps. Installing the pit wiring. Waste material handling. Installing the car electrification and car operating panel. Placing filler weights inside the car for balancing operations, roping. Closing of the brake and re-check of the brake lever operation, safety checks, commissioning and removal of tools. Balancing and final steps. Cleaning down the elevator shaft and disposal of waste materials. Safety inspection (assistance with test weights).

Task split fitter 1 / 2 1 2 1 1 2 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

(2)

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

17 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1.4

Customer experience The focus of your work must always be customer satisfaction. To reach and exceed the customers’ expectations, be polite, constructive and co-operative, and communicate clearly. Remember that for customers, you represent KONE, so ensure that you handle or at least communicate all customer requests and feedback to the correct persons. For more information on how to deliver best-in-class customer experiences through behavior and communication, see the KONE Ambassador program in KONE intranet (search for Ambassador) or contact your supervisor.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

18 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1.5

Explanation for quality requirement table

Quality Requirements:

Required mandatory outcomes upon completion of the chapter.

MAIN hazards identified. Other hazards are described within each chapter.

!!! CAUTION - issues that affect reliability !!!

SORT STABILIZE SHINE STANDARDIZE SUSTAIN Method tools needed:

5S

This area highlights the negative effects of failing to meet the quality requirements.

Reminder of 5S standards.

Tools from the installation kit. Hand tools needed: Tools from the tool kit. 5S Installation Progress Report Progressive reminder to complete this document. QD-181.211 Progressive reminder to complete this document.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

19 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

2

SAFETY When you are working on your own ensure that: – someone in authority knows where you are – regular checks are made to ensure your safety If you have any doubts about single man working on your specific job site, discuss them with your supervisor. Where required, discuss method statements and risk assessments with your supervisor and colleagues before starting work. Work safely and follow local codes and agreed practices.

2.1

General safety The words WARNING and CAUTION are used to highlight possible hazardous situations to persons or equipment as follows:

WARNING: This is to warn about serious safety hazards.

CAUTION: This is to warn about damage to equipment which may also involve a safety hazard.

2.1.1

Safety instructions Following safety instructions should be referred to in conjunction with this installation instruction: – AM-01.03.001 Preventing falls from height when working on elevators, escalators and building doors – AM-01.03.002 Take 5 - Electrical safety when working on elevators – AM-01.03.003 Take 2 - Double security safety practice when using hoists for man riding purposes – AM-01.03.010 Safe working in elevator shaft and machine room areas – Man riding hoist manual

NOTE: Installation work must only be carried out by competent and qualified personnel.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

20 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

2.1.2

Double security safety practise when using hoists for man riding purposes Refer to AM-01.03.003 - Take 2 Double security safety practice when using hoists for man riding purposes. To ensure your and your co-workers personal safety you must always be protected from falling by two independent devices. It is not permitted to drive or to be on top of the suspended platform without double security: 1. Safety gear The safety gear must be connected to the overspeed governor and automatic safety gear trigger. 2. Man riding hoist The man riding hoist must be correctly attached to the car sling using the fittings provided with the hoist. It is not permitted to disconnect the man riding hoist or remove the hook from the car until it has been double secured: 1. Safety gear The car must be secured on the safety gear using the automatic safety gear trigger. 2. Chains The parking chain(s) must secure the car to the agreed anchorage point in the shaft.

2.1.3

Electrical working safety Familiarise yourself with the safety instruction AM-01.03.002 and follow it at all times. Refer to AM-01.03.002 "Take 5 - Electrical Safety when Working on Elevators". The following 5 steps must be taken in the specified order unless there are essential reasons for doing otherwise: 1. 2. 3. 4.

Disconnect the power supply completely. Secure it against re-connection. Verify that the installation is de-energised. Check requirements for earthing in special circumstances. (This operation may only be carried out by qualified personnel in co-operation with the person responsible for the building electrification who must ensure that the technique can be safely employed in this situation.) 5. Provide protection against adjacent live parts.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

21 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

2.1.4

General safety precautions Safety precautions Follow your national lift codes and other safety related regulations. The local safety codes and rules must be obeyed at all times. Follow this instruction. Do not skip any step, otherwise there may be a potentially dangerous situation which you have not considered. ENSURE THAT ELECTRICAL EQUIPMENT AND CONDUCTORS ARE SAFELY DE-ENERGISED BEFORE WORKING ON THEM. A locking off system for main electric supply isolator or other system (for example fuse removal, locking and tagging system, etc.) must be agreed with main contractor before installation commences. Do not connect or disconnect any connectors when the power is ON.

Note In case of conflict between the code and this instruction, rely on your code. Refer to your local procedures for the type of entrance protection required. Warning signs highlight possible hazards. (See page 27.)

Personal safety equipment must be Refer to the list of Personal safety items on available and used as required. page 27. Use only approved manual handling techniques. Do not work at different levels within the same / adjacent elevator shaft enclosures. The rust protection must be removed from Refer to page 56 for specific safety notes. the rails. Otherwise, the safety gear will not operate correctly. Prevent falls from height: 1. Identify all possible fall hazards. 2. Remove the fall hazards, if possible. 3. If it is not possible to remove a fall hazard, then reduce the risk of fall using fall prevention methods. 4. If it is not possible to protect against a fall hazard using fall prevention methods, then use fall arrest equipment but only when verified through specific risk assessment. The provision of suitable rescue equipment, instruction and training must be available to ensure the timely rescue in case of a fall. Refer to AM-01.03.001.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

22 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Safety precautions

Note If applicable, safety harnesses must be used in accordance with your national codes.

CAUTION: Safety harnesses with lanyards. When your safety harness is not secured to a life line or other approved anchorage point, ensure the lanyard does not cause a catching or tripping hazard.

Always position the car at a safe level relative to landing before accessing or egressing. NEVER WORK UNDER A SUSPENDED LOAD! Ensure that the lifting equipment is correctly rated for the task and in good condition. Always use the hoist in accordance with Additional safeguards ensure that there is your local regulations. no unwanted movement of the car due to Refer to AM-01.03.003 Take 2 - safe hoist control or other failure. working when using hoists for man riding purposes. Take care handling waste materials in accordance with your local regulations.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

23 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

2.2

Recommended working postures and ergonomic methods These recommended working postures and ergonomic methods has been identified to contribute a better workplace and your well-being.

Working height Adjust height of working to enable your hands to be within the vertical area of chest and belt buckle.

Working distance Adjust working distance to enable the object to be within length of forearms.

Lifting Focus on the lift, even if the lifted object is light! 1. Go close to the lifted object 2. Use your legs 3. Keep your back untwisted and straight 4. Keep both feet on the same lane

Carrying 1. Keep the lifted object as close to the body as possible 2. Keep your back untwisted and straight

Loading of transport cart Slide the component onto the KONE transport cart instead of lifting it. Moving heavy objects without a handle If the object doesn't contain a handle, push/ slide the object instead of pulling.

NOTE: If work is being carried out by kneeling, with bent back/legs or with hands elevated above chest or object is further than length of forearms, ensure to limit time of exposure and alternate the working postures. Make sure that the working area is un-obstructed and not hindering you.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

24 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

2.3

Installation method safety Special feature The car is used as the working platform.

Note Do not drive on the car roof until the balustrade is fitted and the safety gear is connected. The man riding hoist is used to move the car during the initial stages of the installation.

The man riding hoist is positioned on the car roof and an additional securing rope is attached to the overspeed governor lifting eye. The man riding hoist and overspeed governor are suspended from lifting eyes in top of the elevator shaft. The elevator’s own overspeed governor Refer to AM-01.03.003 Take 2. and safety gear are used during installation. The automatic safety gear trigger engages the safety gear automatically in the event of hoist rope failure or manually when it is necessary to secure the car. The parking chain is used to secure the car to a car guide rail bracket whenever the hoist hook is disconnected from the car or when you are working under the car in the pit. Always keep the chain as tight as possible.

1078317.wmf

When working from the car roof you must always park the car using both the parking chain and the safety gear before disconnecting the hoist hook. Emergency descent from the car roof.

Guide rails are lifted using the car.

At certain times the hoist hook is removed from the car whilst it is still used as a working platform. During these operations the safety gear must be engaged and the parking chain must be used. If there is a power failure on site, it is always possible to move the car to a lower landing level using the brake releasing lever. For emergency descent refer to the man riding handbook. Guide rails are fitted in the conventional way using the sliding clamp to lift each rail.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

25 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Special feature Blocking device

Note

After roping, whenever working on the traction or suspension elements the blocking device must be used.

WARNING: The blocking device is not strong enough on its own to support the weight of the car. In situations where the car is not supported by the ropes it must be secured using the parking chain and safety gear.

When moving the car on manual brake release, do not let it overspeed. Check speed indication LEDs on LOP-CB board. Do not leave the brake open. (Try to limit the motor rotation to 1 second intervals.) If you are working on your own, ensure that someone in charge knows where you are and that regular checks are made to ensure your safety. If you have any doubts about single man working on a specific site, discuss with your supervisor.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

26 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

2.4

Danger and personal protection signs Danger signs Danger Electric shock

Sign

Danger Risk of falling

Sign

Danger Magnetic field

Risk of fire

Corrosion Dermatological risk

Entry prohibited

General hazard warning

Suspended load

Pinching hazard

Sign

Safety gloves, overall, safety shoes with ankle protection, safety helmet, safety goggles, dust mask, hearing protection and safety harness are provided for your personal protection. USE THEM AS REQUIRED. Personal protection signs Mandatory Sign Safety helmet

Mandatory Overall

Sign

Mandatory Dust mask

Hearing protection

Safety shoes with ankle protection

Safety gloves Rubber gloves

Fall prevention equipment

Safety goggles

Fall prevention measures

Man riding hoist mandatory inspection

First aid kit

Sign

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

27 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

3

SITE REQUIREMENTS AND TOOLS

3.1

Site requirements Before installation can start, ensure that the following things have been done:

–

– – – –

The site must be 100 % ready. Transport routes must be defined and agreed as close as possible to the elevator shaft. Elevator shaft tolerances must be checked by the supervisor. Delivery must be complete and on site. Installation start date must be agreed with the customer. When starting the installation and the wall mounted MAP is delivered, ask the builder to finalise the wall at the location of the MAP. This ensures that the wall mounted MAP can be installed without re-adjustment. A locking off system for main electric supply isolator, or other system (for example fuse removal, locking and tagging system, etc.), must be agreed with main contractor before installation commences. Refer to AM-01.03.002 Take 5. Installation tools must be available on site. Recommended hand tools must be available. Personal safety equipment must be available. The site inspection should take place minimum one week before the installation is scheduled to start, in accordance to the delivery process milestones “835”.

Requirement Adequate lighting and 3 -phase power supply must be temporary or permanent positioned for both the elevator and the man riding hoist according to the layout drawing. Lifting eyes must be positioned in the top of the elevator shaft according to the layout drawing and marked with the safe working loads. Right handed lift: 1. Lifting eye for man riding hoist (2000 kg) 2. Lifting eye for machine (1500 kg) 3. Lifting eye for overspeed governor (1500 kg) 4. Lifting eye for KDM drive (if applicable, 1500 kg)

Note Where required, the elevator shaft lighting can be lowered from the top floor and temporarily secured to the entrance protection horizontal stands. If the lifting eye is screw type, the lifting eye must be securely fastened to avoid untightening.

WD

– – – – – –

1

2 4

3 WW

1077488.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

28 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Requirement Typical lifting eye construction: Maximum diameter of hook section 18 mm.

Note

!

max 65 1078300.wmf

Finished floor marks must be on each landing. For group elevators setting out reference lines must be marked on the lowest common floor area. Elevator shaft and pit must be cleaned and The elevator shaft must be watertight. pit waterproofed. C-inserts (if used) must be correctly positioned and cleaned. Suitable material storage areas must be Materials should be stored within 20 metres agreed with builder, adjacent to the elevator or close range from the elevator shaft. shaft. Suitable storage area must be provided for installation tools. Clear, unobstructed access routes to at least one entrance, at or next to the ground floor, for long or bulky items, (guide rails, car components, doors and so on), must be defined and clear of obstructions. Landings must be protected with coverings according to the local safety codes and regulations. Fit temporary barriers around the top and bottom landing entrances wherever temporary protection is removed or landing doors must remain open. The entrance protection must be imperforate. See AM-01.05.016, Installing light entrance protection (LEP). The bars must be secured so that they cannot be moved unintentionally 1078840.wmf horizontally or vertically. Elevator shaft dimensions and tolerances must be in accordance with layout drawings. Suitable provision for disposal of waste According to the local requirements. materials must be available. Appropriate fixing points for safety harnesses must be available.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

29 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

3.2

Pcs. 2 or 3

Tools MonoSpace® tools Tool Pcs. Tool Support bars 1 Automatic safety gear trigger Drawing number: 716161 Drawing number: 803140G01 1 Brake wire rope bracket: 3 support bars are needed if plumbing jig Drawing number: 803144G01 is used. 1 Brake wire rope: Drawing number: 772277G01

1007069.wmf

1

Rope fixing plate Drawing number: 803146

1

Telescopic pipe, Bahco AP-5M Drawing number: KM823588H04

1027222.wmf

1

Parking chain 2 m, 1500 kg Drawing number: 266828

1010242.wmf

2

Plumbing supports (pit) Drawing number: 716177G01

2

Guide rail securing to car roof Drawing number: 773444G01 Guide rail lifting pocket Drawing number: 762396G01

1007070.wmf

1007072.wmf

1

Guide rail lifting clamp for guide rails T70, T82, T89

2 Drawing number: 716165G01

1007079.wmf P17000195.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

30 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Pcs. 1

MonoSpace® tools Tool Pcs. Tool Counterweight guide rail positioning tool 1 Unwinding device Drawing number: 716175G01 Drawing number: 504610G01

1007076.wmf

1

Hoist test bracket, max. load 2000 kg Drawing number: 716157G01

1

Counterweight guide rail alignment tool Drawing number: 716180G01

4

Eyebolt M8 (male) Drawing number: 934990

1

Eyeloop M10 (female) + M10 T-bolt Drawing number: 754258

3

Shackle 12 mm tap, 1500 kg Drawing number: 754257

1007084.wmf

4

1007074.wmf

Eyebolt M12 (male) Drawing number: 266824

1026867.wmf

1 1 1

1026867.wmf

Hoisting chains: Extension chain 1.5 m, 500 kg Drawing number: 266827 Shortenable chain 2 x 1.5 m, 500 kg Drawing number: 266826 Car/door installation chain 2 x 0.5 m, 500 kg Drawing number: 266825

1026868.wmf

1007081.wmf 1007078.wmf

1

Rope grip for rope reeler securing, 9 mm Drawing number: 754257

1

Shackle for car roof rope reeler securing, 8 mm tap, 350 kg Drawing number: 754257

1007082.wmf

1007083.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

31 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Pcs. 1

Other installation tools Pcs. Tool 1 Manual chain hoist, capacity 500 kg (Yale compact 500 or equivalent).

Tool Man riding hoist + pulleys, 750 kg / 1000 kg capacity.

See hoist equipment parts on page 43.

A = 289 mm H = 190 mm

1007086.wmf

1

Overspeed governor extension rope Drawing number: 772277G05

1033403.wmf

1 set

Machine transporting wheels Drawing number: 715802

1

Elastic grip L=1m

1031365.wmf

1007090.wmf

1

Site trolley Drawing number: 589519

1

Overspeed governor hanger kit including: – OSG hanger assembly – Pulley bracket assembly – Climbing rope Drawing number 823588G01

1078301.wmf

1010244.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

32 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Pcs. 1

Other installation tools Tool Pcs. Tool Battery tool 2 Transportation tool (used with Cable (Drawing number: 859326) and transportation wheels and axle) 9V battery (supplied locally) Drawing number: 854900D01 Used with construction-time power supply.

4x

1078366.wmf

1039959-1.wmf

1

Rope clamp Drawing number: KM839679G01

2

Hilti PMP34 / PMP45 point laser

1078890.wmf

1060910.wmf

1

Carpenters ruler

1

Work stool Drawing number: 265173

PMP 34

HILTI

+30

+20

+10

Laser alignment tool Drawing number: 1349459D01

+10

1

+20

Target plate +30

2

M8x50

1073236.wmf

laserpl2.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

33 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Pcs. 2

Tool Levelling plate

Other installation tools Pcs. Tool 1 Guide rail transportation tool Drawing number: KM971149G01

1048308.wmf

1060909.wmf

1

Rope socket 6-8 Drawing number: KM971423G01

1

Electrostatic discharge (ESD) kit Needed to protect the components from damage if any PC boards are replaced. (KM857505)

1060911.wmf

1072347.wmf

2

Installation jig Drawing number: KM756128 Included in AMD door delivery

1

Telescopic ramps Drawing number: KM966635

1073260.wmf

1077935.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

34 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

3.2.1

Hand tools (recommended) Tool

Carpenter’s pencil Tape measure, L 3.0 m Multimeter, protected against high voltage Hammer drilling machine, with dust collector Cordless drilling machine; with adjustable torque for car and landing doors and car installation. One extra accumulator (battery), bit cassette including Phillips head and flat heads in different sizes, drill bit cassette (sizes 1.5 - 10 mm). Phillips head bit 150 - 200 mm. Tool for concrete inserts Spanners: U end and ring end. Sizes 10, 11, 12, 13, 15, 16, 17, 18, 19 mm. Min. thickness for 16 - 19 mm spanners is 5 mm. Ratchet 1/2" drive Extension L 200 mm 1/2" Sockets (deep) 1/2", 13, 15, 16, 17, 18, 19 mm Carpenter’s hammer, 6 Oz. rubber handle, “shock absorbent” Vice grip/polie grip: L 150 mm and L 250 mm Engineers squares: 300 x 150 - 200 mm and 750 x 350 mm Side cutter, isolated handles (L 170 mm) File for guide rail joints, normal model Knife Disc cutter, disc > 125 mm Engineers square, adjustable block width 30 mm Pulling rope to pull the man riding hoist rope (plastic, 70 m, Ø6...8 mm) Allen keys, set 3 - 12 mm 2 G-clamps

Tool Lockable tool box for the normal hand tools Carpenter’s ruler Plastic tuning screw driver Adjustable spanner, L 200 - (250) mm Drill bits: 6 mm (light fitting, pit stop switches) 8 mm (trunking) 10 mm (pit ladder, travelling cable wall fixing) 12 mm L (150) (Hilti, for cutting through reinforcing bars) Crow bar, L 500- 700 mm Screwdrivers: Flat headed 5 mm L 200 mm. Electrical, isolated 2.5-3 mm head L150-200mm Phillips head: Standard size L 200 mm. Ratchet 1/4" drive small model Extension 1/4", L 40 - 150 mm Sockets 1/4" drive, 10, 11, 12, 13 mm Sledge hammer, 1000 gram Hammer side flat, end drop forged Magnetic spirit levels, lengths 700 and 1500 mm Rivet pliers, replaceable head to cover the different rivet sizes Long nose pliers, medium model (L 170 mm) Rope cutting pliers, 8 mm Hacksaw, standard model 4 pcs plumbing weights, max. 10 kg/each (diameter max. 40 mm, length max. 300 mm) Sheet metal cutters, professional quality for 0.6...1.5 mm steel sheet 2 vacuum handles, capacity 40 - 80 kg

1007097.wmf

1010245.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

35 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

4

OFFLOADING AND DISTRIBUTION

CAUTION: For personal safety and to prevent any damage to the components: – Keep the working areas clear and unobstructed. – Never go under any suspended load. – Use correct manual lifting techniques. – Wear gloves to protect your hands. – Always wear a helmet. – Wear safety harness and fix it to an approved fixing point while working in areas where there is risk of injury from falling. – Wear goggles and dust masks as necessary. – Use hearing protection as necessary. – When using the telescopic ramps ensure they are parallel and cannot slip off leading edge. Introduce yourself to the person responsible for the site. Familiarise yourself with the site facilities, the local rules, safety requirements and site management procedures.

4.1

Offloading and distributing materials

NOTE: The 150 kg (300 kg / pair) maximum WLL (working load limit) marking of the telescopic ramps is based on single axle trolley usage. On specific tested method steps, where a twin axle assembly is used (such as machine transport), the load is more evenly distributed across the ramps. In such cases the WLL is increased to 380 kg / pair of ramps. Always follow the designated method description. WLL 300 kg / pair of ramps

WLL 380 kg / pair of ramps

1078918.wmf

1078916.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

36 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1. Fix the transportation wheels to machine package while unloading. 2. Use wooden blocks to tilt machine box when removing the wheels.

1060914.wmf

1060912.wmf

Offload the material to the destinated storage area. Arrange the materials to ensure easy access to each component in the installation order.

NOTE: Car floor is at the oppposite side of the packing list. NOTE: A number at top of each crate indicates the installation order. Place the machine box so that the side with the holes is downwards. When offloading the machine from the vehicle, put it into vertical position and use a forklift to place machine onto the axle and wheels. Push the machine into the storage area. Remove the axle and wheels and leave the crate in upright position on two pieces of wood. The female end of the guide rail bundle is marked with tape. Locate the bundle so that the male side faces the elevator shaft. Handle the bundle carefully so as not to damage ends. Put the guide rail bundle on a higher stable working level to achieve a good working height of 1.0 m. It is important that the tools and materials are positioned according to the installation order to achieve and maintain a controlled installation environment throughout the installation. Do not open the packages until you are ready to install the equipment. Check against the material documentation that the delivery is complete. Position the tools and materials to correct levels before the installation starts.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

37 (340)

AM-01.01.250 (Draft A) 2012-08-28

Mono3 - Unloading order

Copyright ©2012 KONE Corporation

All rights reserved.

xxxxxxxx (Draft -) 2012-05-24 Copyright © 2012 KONE Corporation All rights reserved.

Compiled by: Information Product Author / Ville Malmiala Checked by: Global Installation Support / Solution Manager, Global Packing / Konsti Ville Approved by: Global Installation Support / Anssi Venho

KONE MonoSpace® 3.0

Installation Instruction

1079322.pdf

DRAFT

38 (340)

AM-01.01.250

(Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Package group 100 200

Group header Installation requisites Guide rails and shaft beams

300

Doors

400

Machine room

500

Shaft and machine room Car Car sling and frame

600 700

Package label 110 120 210 220 230 311 312 330 331 410 420 430 510 440 / 540 610 710 720 730

A Topmost landing – Long tool box – Hand tools – Man riding hoist top pulley – Elevator shaft lighting (if applicable) – Overspeed governor and rope – Parking plate – Rope suspension, counterweight side B Entrance level / Storage area – Smaller tool box – Man riding hoist, ASGT – Working stool – Counterweight guide alignment tools – Guide rails and brackets – Counterweight, filler weights – Car sling, car – Machine – Car door and landing doors – SEP, MAP, drive panel, COP – Elevator shaft electrification – Pit ladder – Ropes – Wiring material

Package label text Installation requisites Overspeed governor Guide rails Guide rail fixings Shaft beams Frame / Fronts Door panels Door operator Railing Machine Ropes Shaft electrification panel Shaft equipment Wiring Car Car sling Counterweight frame Filler weights

A

B

1007099.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

39 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

4.2

Offloading and transporting landing doors 1. Keep the area on the side of the crate with the identification label “OPEN THIS SIDE” unobstructed. 2. Always transport parts of door one at a time. 3. The top tracks will be stored in the shaft mechanics box. 4. Open the narrow side of the card board box marked “Open this side” by cutting the vertical edges of the side. This is to gain access to the door panels. 5. Remove the top wooden support to access to the sills. 6. When extracting the door panels, do not break the two wooden rings around them. Slide the door panels out the opening. 7. When the panels are stored into the car or at the landing, ensure that the guide shoes are facing up in order to not damage them.

a31294e4.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

40 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5

INSTALLING MAN RIDING HOIST AND OVERSPEED GOVERNOR

Quality Requirements: Man riding hoist and accessories – inspected and certified (inspection period validity to meet local code) – ONLY TRAINED PERSONS TO USE THE HOIST! – lifting hook in shaft tested Car overspeed governor – installed to temporary position – check data label to ensure correct type and tripping speed – ensure correct tripping direction – ensure the rope is on the small pulley

1075605.wmf

!!! CAUTION - issues that affect reliability !!!

5S

N/A

NOTE: Check carefully that the OSG rope is correctly on the groove and UNDERNEATH the internal rope guard!

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist test bracket, overspeed governor hanger, telescopic pole, site trolley, man riding hoist + rope + accessories + hoist test plate (fuse plate) Hand tools needed: Pencil, tape measure, hammer drill, hammer, 2 x spanner (19 mm), pulling rope 5S Installation Progress Report N/A QD-181.211 QD 1 completed

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

41 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5.1

Man riding hoist parts

NOTE: The man riding hoist type described in this instruction is Tirak X750.

Pos. 1 2 3 4 5 6 7 8 9 10 11 12 13 14.1 14.2 15 16

Item Diverter pulley including the safety rope Electric hoist Tension weight Manual rope reeler for maximum 60 m rope. Minimum rope length = 2 x elevator shaft height. Safety pin no. 2. 6 mm Electric supply extension cable for main power supply, 45 m, 5 x 1.5 mm2 Pendant controller Extension cable for the pendant control Car adapter for the hoist Car adapter for the hook Adapter axle Split pin 6.3 x 40 Diverter pulley Ø160 mm Safety pin 5 x 32 mm for diverting pulley Safety pin no. 2. 6 mm Tension weight pulley Ø130 mm Tension spring (guide for rope)

Greifzug component no. 33009 57497 30158 12056 16537

53877 53887 72415 63496 53997 63656 12056 20205 8363

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

42 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

14.1

7. 1.

13.

8. 6. 2.

5. 9. 12.

16. 3.

11.

15. 4. 11. 10.

14.2.

P17000140.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

43 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5.2

Work positioning equipment or restraint system Work positioning or restraint systems are systems of personal protection designed to secure the user in a safe position where it is not possible to fall. The restraint may also be used as an additional measure to prevent fall when working close to or leaning over the basic entrance protection, for example, when installing components at the top of an elevator shaft. The area around the fall hazard must be segregated to prevent risks to others. Work positioning system CAUTION: Work positioning or restraint systems must not be used to arrest a fall.

1072131.wmf

Typical equipment includes: – Body belt. Note: A full body harness is sometimes used but is less suitable for low level anchor point. • Adjustable lanyard (without shock absorber). Keep the lanyard as short as possible and take extreme care that the lanyard cannot be damaged by sharp edges. • Suitable fixing point. The anchorage point strength requirements vary, but they must be capable of supporting around double the maximum pull force of a person and be in accordance with local regulations.

KONE methods do not support the use of work positioning or restraint systems as primary fall prevention systems. This system is suitable as additional protection to the primary protection or where there is a limited risk of injury. They are only to be used where no other better solution is possible, subject to specific risk assessment. (for example, existing elevator with no car top balustrade).

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

44 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5.3

Safety checks Make the following safety checks. Item Lifting equipment and suspension eyes.

Hoist and lifting equipment. Plugs and cables. Emergency stop button and limit switches (if applicable). Safety harnesses and ropes.

5.4

Requirement Must be load marked, tested and in good condition according to local requirements. Must be tested according to local requirements. Must be in good condition. Must prevent movement of hoist when contacts are open. Must be inspected and in good condition. When used, they must always be securely attached to approved fixing points.

Risk Falling loads.

Electric shock. Uncontrolled movement of hoist/car. Falling.

Transporting 1. Use site trolley to transport the man riding hoist.

SMW06.wmf

1060916.wmf

1060917.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

45 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5.5

Routing the man riding hoist rope and cable

WARNING: When there is a risk of falling wear a tethering system when working at unguarded landing entrances. Always install the hoist from the lowest landing level. For more information, see AM-01.03.001. 1. Lower the power supply cable from the topmost landing to the pit. Connect to hoist. Check the operation of the hoist safety functions. 2. Drive out the hoist rope and pull it to the top floor using the lifting rope. 1 = rope entry, 2 = rope exit If the hoist motor does not run, reverse two phases in the plug by rotating the phase changer* in the plug housing 3. Pull the hoist rope to the topmost landing. Allow 8 metres of slack to reach the elevator shaft ceiling. Loop the hoisting rope through the pulley.

1072131.wmf

*

1

2

P17000199.wmf

P17000107.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

46 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5.6

Installing overspeed governor hanger

WARNING: Check the correct orientation for the overspeed governor. The rope guard must face the shaft wall.

NOTE: The counterweight overspeed governor (if any) must have higher tripping speed than the car overspeed governor.

*

~4 m

~4 m

1. Route the pulling rope through the hanger. Tighten the lower hook to maintain in correct position. *) Make a loop at the rope end to enable pulling the rope back to the landing. 2. Lift the hanger to the lifting eye.

1079201.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

47 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

3. 4. 5. 6.

Pass the rope over the small groove of the OSG. Check the tripping direction. Secure rope ends together and lower to the pit. Check that ropes do not get entangled. Pull the overspeed governor to hanger. The rope guard must face the wall. Remove the pulling rope. It is needed for car floor installation.

1078306.wmf

5.7

Fixing the man riding hoist rope 1. Attach the securing rope of the hoist diverting pulley to machine lifting eye. Use telescopic pole and adaptor bracket. Strengthen adaptor bracket: 1 = M6 flange nuts from car bolt delivery, 2 = M6 x 40 bolt, provided locally. 2. Fit hoist rope over the diverting pulley. Attach the pulley to the hoist suspension eye.

1

2

1078319.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

48 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5.8

Lowering the man riding hoist hook to the pit 1. Drive out the hoist rope and lower the hook to the pit. 2. Clip the hoist hook over the suspension bar on the hoist. 3. Fit the car parking chain (capacity 1500 kg) to the underside of the hoist and drive the hoist into the elevator shaft

1009514.wmf

P17000146.wmf

5.9

Pit ladder

PH

1m

1. When using the ladder, ensure the suitable angle between the ladder and the pit floor. 2. Secure the ladder to the wall using a CWT guide rail bracket and large cable tie. Install the bracket while entrance protection is fitted. 3. Fix the pit ladder wall fixing bracket to the machine side wall. 4. Fix the securing strap is to the wall to prevent unwanted removal of the ladder.

PH /3 1078313.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

49 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

5.10

Testing the hoist equipment If the lifting eye or suspension element for the man riding hoist diverter pulley has not been tested and certified, perform and record the test. The test ensures that the hoist equipment will take the maximum load hoisted during the installation.

WARNING: No one is allowed to be in the elevator shaft during this test.

WARNING: The hoist can be used for material transportation after test. Do not use the hoist for man riding.

1. Install the hoist test bracket on the side wall of the elevator shaft. 2. Attach the dynamometer or test plate (breaking strength 2000 kg, supplied locally) between the hoist and the hoist test bracket. Shorten the parking chain to 300 mm. 3. Drive the hoist slowly upwards until the hoist ropes are almost under tension. Take up the tension smoothly. Sudden loadings may damage the equipment. 4. Run continuously until the load limit of the hoist is reached or the test plate breaks. Motor power supply is automatically disconnected. Drive the hoist downwards to reset it. 5. Write your name and test date on the test plate and store it. Fix it to the tested lifting point after guide rail installation.

1010613.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

50 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

6

PLUMBING

Quality Requirements: – – – –

plumbing table is completed dimensions in the pit are similar to those in layout drawings lasers are positioned on the pit floor according to the plumbing table laser tools are calibrated, clean and batteries checked

1075617.wmf

!!! CAUTION - issues that affect reliability !!!

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Pit ladder, lasers Hand tools needed: Tape measure, pencil, spirit level 5S Installation Progress Report N/A QD-181.211 QD 2 completed

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

51 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

6.1

Elevator shaft plumbing 1. Place laser tools on the pit floor to the LL dimension. Check the accuracy of the laser beams by measuring dimension LL at second landing. See layout drawings. 2. Measure dimensions at each landing and fill in the plumbing table. For nominal dimensions see layout drawings. Store plumbing table with other elevator documentation. 3. Mark the landing door centre line (A) below the lowest landing LL

A1

LL

A2

!

Plumbing table A5

x1

A6 A3

x1

A1

x2

A4

6.2

(A)

1051761.wmf

1048316.wmf

LL

A2

x2 1051760.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

52 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Elevator number:

Measured by:

Date:

Position SH (headroom height) H (travel height) PH (pit depth) WW (elevator shaft width) WD (elevator shaft depth) x1 (vertical straightness of pit wall) x2 (vertical straightness of pit wall)

A1

A2

Measured (mm)

A3

A4

A5

A6

LL

Nominal dimension Level 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

53 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

7

MECHANICAL INSTALLATION IN THE PIT

Quality Requirements: Pit ladder – installed correctly (ensure that length meets local code) Guide rail brackets (first 2 rounds) – installed according to the layout drawings – level in all planes Guide rails – clean, not rusty – checked for straightness – installed correct way up – installed according to the layout drawings – vertically aligned, parallel to each other, maximum DBG deviation of -0 mm, +1 mm – edge trim fitted to car guide clips of lowest bracket – all remaining guide rails placed in pit (if enough space) Buffers (car and counterweight) – installed according to the layout drawings – installed level to each other (if dual buffers) – oil level checked (if oil buffers) Counterweight frame – CWT shoes aligned and not twisted Dividing beams (optional) 1075519.wmf

Overspeed governor tension weight – installed to correct height, minimum distance from bottom of weight to pit floor is 120 mm – adjusted to ensure the slack rope switch operates

!!! CAUTION - issues that affect reliability !!! Incorrectly installed guide rails causes: – ride comfort issues (noise / vibration) – drive faults / failures – levelling accuracy problems – premature shoe liner wear (car / counterweight) Incorrectly adjusted counterweight shoes causes: – ride comfort issues (noise / vibration) – drive faults / failures – premature shoe liner wear Incorrectly adjusted OSG tension weight causes: – safety circuit break due to rope stretch – noise / vibration from rope rubbing guard

SORT STABILIZE SHINE STANDARDIZE SUSTAIN Method tools needed: Man riding hoist + accessories, guide rail transportation tools, guide rail lifting clamp, Hilti RA laser kit, guide rail alignment and DBG tools, machine transport wheel + axle sets, work stool, timber pieces Hand tools needed: G-clamp, hammer drill, hammer, ratchet + sockets (18, 19 mm), spanner (13, 15, 18, 19 mm), small crowbar or podger spanner (19 mm), tape measure, pencil, spirit level 5S Installation Progress Report

5S

Lift pit equipment installed, Counterweight installed, Guide rails installed = 25% QD-181.211 QD 3 completed

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

54 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

7.1

Guide rail preparing

WARNING: The guide rail bundle may fall down when metal straps are opened. Open the middle strap first and then the outer straps.

WARNING: Remove the rust protection from the guide rails, otherwise the safety gear will not operate correctly.

NOTE: Before drilling in the pit area, check any water proofing that may be affected and limitations to drilling depths.

Guide rail principle:

4 3 2 1

Travelling height > 3.5 m: 1. First guide rails (L = 5 m) 2. Intermediate guide rails (L = 5 m) 3. Second topmost guide rails (L = depends on the shaft height) 4. Topmost guide rails (L = 2.5 m)

3 2 1

Travelling height  3.5 m: 1. First guide rails (L = 2.5 m) 2. Intermediate guide rails (L = depends on the shaft height) 3. Topmost guide rails (L = 2.5 m)

1078541.wmf

1078540.wmf

NOTE: Identify the topmost guide rail on the machine side according to the machine fixing holes.

1078546.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

55 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

1. 2. 3. 4.

Use guide rail transportation tool to transport the car guide rails (T70-T89). Clean the guide rails and fish plates thoroughly. Fix the fish plates and jointing pieces. Check the guide rail straightness. Use a string or a plumb wire. Adjust the DBG at the alignment tool*. Set the counterweight guide rail positioning tool** to the correct length. Refer to the layout drawings. max 5mm

max 5mm

max 2.5mm

max 2.5mm

*

** 1078394.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

56 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

7.2

Installing dividing beams (optional) 1. Install the first two dividing beams before car installation. Align using the lasers. See layout drawings. 2. Install the rest of the dividing beams after car installation. Align using the lasers and car top balustrade uprights.

1

2

1010422.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

57 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

7.3

Guide rail brackets

Combination / car single bracket CWT single bracket A = 170 mm

Car single bracket (25 10

3

3

> 10

1. Centre opening measurements 2. Side opening measurements

3

2

2

1010116.wmf

Railing 1

190

110* 77**

10

2 3

155

1. Centre lock holder 2. Landing sill line 3. Car sill line

13

13

30

* Open ** Pressed

1

20

(NH / 2)

85

HH

Railing 1. Landing door lock and contacts. Standard. Protection class IP20.

1. Check the lock function. The lock hook must rest on the buffer in closed position. The lock gap must be 1-2 mm when the hangers are closed and lean against the end buffer. Check the contact functions. Check that the lock gap does not break the door contact function. Note: The door lock is not adjustable. 2. Check the lock roller clearance to the coupler at all landings. Nominal clearance = 13 mm, minimum clearance = 8 mm. If not correct, check that the car is plumb and aligned in back to front direction or re-align the door. Re-check clearance after door operator installation.

1007328.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

145 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

13.6

Installing panels and strips (front type version only)

13.6.1

Installing side extension panel 1. Slide the side extension panel into position. 2. Fix the panel to the door frame. To fulfil EN81, fix 2 self-drilling screws at the bottom. Check that there is no visible gap on landing side. 3. Align the panel to the door frame. Drill and fix the support brackets in the shaft. 4. Install the panel extension on the flooring with the nail anchors.

2

1

1. No gap 2. Front panel 3. Upright 4. Self drilling screws

2 4

3

1 2

3 1010120.wmf

1060880.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

146 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

13.6.2

Installing top extension panel 1. 2. 3. 4.

Install the joining strip to the lintel with self drilling screws. Lift in the top extension panel from the landing side. Fix the panel to the joining strip and side extension panels. Fix the panel to the shaft wall using support brackets. Check that the panel is plumb.

3

1

4

2

4

3

1010121.wmf

1. Joining strip 2. Top extension panel 3. Lintel 4. Side extension panel

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

147 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

13.6.3

Installing backing strips

75

75

75

1

2

100

100

150 75

100

75

100

1. Check that the wall surface is smooth and clean. If the wall is not smooth, overbend the cover strip slightly to ensure a firm pressure to the panels. 2. Cut the backing strips to fit. Check that the backing strip is tight against the wall. Fix to the door with self drilling screws.

3

100

75

100

4 1010126.wmf

1. Front 2. Extended front 3. Front MAP 4. Backing strip

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

148 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

13.6.4

Installing cover strips (front type version only) 1. Fit the top cover strip over the backing strip. Use wooden block and hammer if necessary. Wooden block must cover the cover strip width and be minimum 300 mm long to avoid possible dents. 2. Cut the side cover strips (from lower part) to fit in the door opening. 3. Fit the side cover strips over the backing strips. If extended front type door, fit the upper side cover strip first. 4. Secure the side cover strip with the locking screws on side panel.

1

1. Top cover strip 2. Side cover strip 3. Upper side cover strip

3

2 NOTE: Top cover strip for controller cabinet. 1007335.wmf

B B A

A A

A

A-A

B-B 1007334.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

149 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

13.7

Installing landing toe guards

NOTE: Do not install the landing toe guards for topmost and lowest landings yet. They will be installed after electrification. 1. Install the toe guard to the sill. Use the special screws provided.

1078267.wmf

2. If the toe guard overlaps the top track of the next landing door, cut it and secure to the door fixings. If this is not possible, manufacture new toe guard locally.

1

1 = Shortened toe guard 2 = Self tapping screw 3 = Timber insert

2 3 1007469.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

150 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

14

CAR FRONT INSTALLATION

Quality Requirements: HANDLE MATERIALS CAREFULLY TO AVOID DAMAGE! Car front – front wall panels and lintel installed – aligned and dimensions checked for accurate LL dimension – diagonal reference (equal corner to corner size: cross measurement) – height from sill to lintel checked – correct number of fixings used • lintel = minimum 1 fixing per 100 mm • front wall panels = minimum 3 fixings at top & bottom • stiffeners MUST have fixing screws installed – no rattling noise during knock & feel test – all protective plastic paper removed from joints etc. Door operator brackets – installed according to instruction

1077317.wmf

!!! CAUTION - issues that affect reliability !!!

5S

Incorrectly installed car front wall causes: – poor visual appearance – noise / vibration – misalignment with car doors – misalignment with landing doors – unnecessary stress forces to car

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist

Incorrectly installed door operator brackets causes: – misalignment of door operator with car sill which affects car door running – misalignment of running clearance between car coupler and landing lock rollers and landing sills – door running problems (noise / vibration)

Hand tools needed: Tape measure, 2 x spanner (10, 13 mm), ratchet + sockets (10, 13 mm), square, spirit level 5S Installation Progress Report N/A QD-181.211 QD 6 continued

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

151 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

14.1

Installing car front walls

NOTE: Fix the front wall panels and lintel with bolts at equal distances (maximum distance between two bolts is 100 mm). Fit a bolt through each stiffener (if any). 1. Turn the roof front stiffener the right way up (if installed upside down). 2. Install the front wall panels. 3. Install the lintel and the door operator brackets. For bracket types, see next page. Adjust the lintel height (HH) according to the finished car floor level. 4. Install the jamb mounted destination indicator (JM-DIN, if applicable). For more information, see AM-12.20.017.

3

2

10

3

3

3

2

1009994.wmf

Centre opening Step 1

Side opening

Action Check the lock function. – Ensure that the lock hook overlaps the lock beak properly in closed position. – The lock gap should be 1...2 mm when the hangers are fully closed and leans against the end buffer. – Check the contact functions.

Note The lock is not adjustable!

Ensure that the lock gap do not brake the door contact function.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

177 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

15.13.2 Car door lock and contacts for railing 2 Standard protection class IP20

>10

2

3

3

>10

3

2

1009995.wmf

Centre opening Step 1

Side opening

Action Check the lock function. – The lock hook must rest on the lock hook buffer in closed position. – The lock gap should be 1...2 mm when the hangers are fully closed and leans against the end buffer. – Check the contact functions.

Note The lock is not adjustable! Not valid when “Optional”

Ensure that the lock gap do not brake the door contact function.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

178 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

16

KONE SIGNALIZATION SYSTEM (KSS) INSTALLATION

Quality Requirements: Landing signalization – aligned to frame / wall, position according to layout drawings – cable routing clear of obstruction, provide slack for future maintenance purposes – plugs properly inserted into sockets and not under strain COP – flush and securely installed – take care not to damage the car wall when installing COP – cable routing clear of obstruction, provide slack for future maintenance purposes – plugs properly inserted into sockets and not under strain

!!! CAUTION - issues that affect reliability !!! Incorrectly installed signalization causes: – poor visual appearance – plugs not inserted correctly to sockets can cause unnecessary disconnections / failures of unit – cables under strain can cause unnecessary disconnections (doors, car, travelling past guide brackets etc.) – incorrectly routed / secured cables can be damaged by moving parts – failing to provide sufficient slack for future maintenance purposes can lead to damage to the cables / unit

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist, work stool Hand tools needed: Battery drill / driver, Phillips screwdriver, hammer drill, hammer, side cutters, allen keys, tape measure 5S Installation Progress Report N/A QD-181.211 N/A

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

179 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

16.1

Hall indicator (KSH) and landing call station (KSL) Step 1 2 3 4

Action Fix the mounting bracket to wall or door frame with screws. Route and connect the cable to the unit. Slide the device to the mounting bracket. Secure using allen screw.

Note

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

180 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

16.2

Installing COP Step 1 2 3 4

Action Route and connect COP cables. Fix the limit bracket below COP. Lift the COP in position. Secure in position using screw.

Note

*) Be careful not to scratch the wall.

*)

1078608.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

181 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

16.3

Hall display (KSJ) Step 1 2 3 4 5

Action Remove the cover. Connect the cables. Insert the unit in the car wall cut out. Secure using screws. Re-fix the cover.

Note

1079083.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

182 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

17

INSTALLING MAP

Quality Requirements: MAP (maintenance access panel) – wall type = aligned to wall, position according to layout drawing – frame type = aligned to frame – door operation checked – locks operation checked with key – no rattling noise during knock & feel test – all protective plastic paper removed from joints etc. – inspect for any sharp edges and de-burr if necessary – install fire protection (if needed)

1076668.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly installed / aligned MAP causes: – MAP door lock operation failure

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist Hand tools needed: Battery drill / driver, Phillips screwdriver, hammer drill, hammer, side cutters, tape measure, spirit level, ratchet + socket (19 mm, wall MAP) 5S Installation Progress Report N/A QD-181.211 N/A

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

183 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

17.1

Installing wall type MAP 1. Install the MAP (1 = surface mounted, 2 = flush mounted). 2. Route the cables to the elevator shaft. Check that the cables are clear of all moving parts of the elevator.

1

2

1007410.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

184 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

17.2

Installing door type MAP

NOTE: Use gloves, protect your arms and use dustmask when handling rockwool. 1. 2. 3. 4.

Install the MAP body. Fire rated doors: Fit rockwool pieces to top and bottom consoles. Install the components inside the MAP body. Route the cables to the elevator shaft. Check that the cables are clear of all moving parts of the elevator. 5. Fire rated front type doors: Install the fire protection plates.

55

1076552.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

185 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

18

IDE300 (OPTIONAL) 1. Install and connect the components for IDE300 (integration of doors and elevator) if any. For more information, see AM-13.20.018.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

186 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

19

ELECTRIFICATION AT TOP OF THE ELEVATOR SHAFT (KDL16S)

Quality Requirements: SEP, drive, THD filter, trunkings, external braking resistor (if any) – installed to correct position according to layout drawings Accessories (EBD etc.) – installed to correct position according to layout drawings Cables between shaft top components – routed and connected, free of obstruction – encoder cable routed separately (not grouped with machine cables) – plugs properly inserted into sockets – all ‘screw type’ cable terminations tightened, ensure no loose cable strands – earthings checked – cable grounding / shields to be correctly clamped – ensure no damage has occurred during installation

NOTE: Ensure that all covers are closed after installation. 1076397.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly installed shaft top electrification causes: – equipment (SEP, drive etc.) not installed to layout drawing position will interfere with required running clearance from ropes or car – accessories (EBD etc.) not installed to layout drawing position will interfere with required safety spaces, running clearances Incorrectly installed shaft top cabling causes: – incorrectly routed encoder cable can cause poor encoder reference feedback due to magnetic field disturbances from machine cables. This leads to poor ride comfort and drive faults – plugs not inserted correctly to sockets can cause unnecessary disconnections – earthing / shield clamps not used correctly will NOT provide the required grounding to remove signal interference – loose ‘screw type’ terminals cause unnecessary disconnections

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist Hand tools needed: Tape measure, spirit level, pencil, hammer drill, hammer, side cutters, 2 x spanner (10 mm), ratchet + socket (19 mm, EBD), spanner (17, 19 mm), allen keys, spanner (7 mm), 2 x spanner (8 mm), TORX screwdriver (T10), electrical terminal screwdriver, multigrip pliers 5S Installation Progress Report Lift Controller Installed QD-181.211 QD 7 commenced

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

187 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

WARNING: During electrification work the power must be off. Ensure that the power to the main supply cable cannot be turned on. Remove fuses and lock the main switches. Notice the separate lighting supplies. For more information, see AM-01.03.002.

CAUTION: When drilling above drive, SEP or MAP, protect the panels from dust.

CAUTION: If there is a danger of condensed water, on the wire or cable surface, to enter electrical components or connectors in the elevator shaft, form a loop before the cable entry or connector. This cable loop method is recommended for all installations and mandatory in wet/humid operating conditions.

CAUTION: When installing the machine cables o E ensure the following things: 90 Encoder and thermistor cables must be separated from motor supply and brake control cables. Otherwise there might be disturbances 100mm in the encoder signals. These cables can cross each other at an angle of 90 degrees. If these cables are routed 1 parallel, the minimum clearance between two 4 cable groups must be 100 mm. 1 = encoder cable, 2 = brake control cable, 3 = motor cable, 4 = thermistor cable

2 3

NOTE: Leave sufficient cable length to allow the SEP and drive panels to be moved from behind the ropes to the maintenance position.

NOTE: For more information on ECB-1 Single Line Regenerative Unit, see AM-11.65.038.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

188 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

19.1

Overview (KDL16S)

Show the encoder cable running separately from the other machine cables 8 9 10

1

2 3 4 5

6 7

1076394.wmf

1. Machine 2. Drive panel 3. THD filter 4. Maintenance access panel (MAP) 5. Shaft electrification panel (SEP)

6. Fuse box 7. External braking resistor (optional) 8. Overspeed governor (OSG) contact 9. Load weighing device (LWD) at rope terminal 10. Elevator shaft lighting

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

189 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

19.2

Opening drive covers

WARNING: The covers must be closed when switching the power on. 1. Removing the cover plate.

1076584.pdf

2. Opening the slide deck. Keep the slide deck closed during the drive module installation to prevent damaging the internal components.

1075530.wmf 1075532.wmf

1075533.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

190 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

19.3

Installing SEP and drive panels, brake resistor and trunkings (KDL16S)

NOTE: For exact location of the components, see delivery documents. 1. Install the brackets below the machine (with the guide rail bracket wall fixing bolts). 2. Install the drive panel to the back plate.

1079306.wmf

3. Install the drive panel, SEP and travelling cable hanger.

1079311.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

191 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

4. Install the metal plate trunkings. 5. Install the 2 m piece of trunking beside the drive panel. 6. Install the emergency battery drive unit (EBD) and THD filter. *) Install the external braking resistor (optional, only if rated speed is 1.6 m/s or above).

EBD

4

THD

*

5

1076579.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

192 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

19.4

Connecting machine cables (KDL16S)

WARNING: Ensure that the power supply is safely locked off. For more information, see AM-01.03.002.

XMEN5 XT1 U,V,W

XBR4 XBRE2

PE

1076539.wmf

Cable Thermistor cable Machine supply cable Brake cable Encoder cable External braking resistor cable

To drive XT1 U, V, W, PE XBR4 XMEN5 XBRE2

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

193 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

19.5

Cabling: MAP - drive, SEP - drive (KDL16S)

XLG1 XBAT1 XL1 XS3

XL6

T1,T2,T3 PE T1,T2, T3,PE X4 XM14 XD1

1076370.wmf

*) THD filter Cable Supply cable Load weighing cable Cable Safety chain cable Battery backup cable LCE cable

From MAP T1, T2, T3, PE XL6

To drive T1, T2, T3, PE XLG1

From SEP

To drive

XD1 XM14 X4

XS3 XBAT1 XL1

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

194 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

20

ELECTRIFICATION AT TOP OF THE ELEVATOR SHAFT (KDM40)

Quality Requirements: SEP, drive, KDA module, THD filter, trunkings – installed to correct position according to layout drawings Accessories (EBD etc.) – installed to correct position according to layout drawings Cables between shaft top components – routed and connected, free of obstruction – encoder cable routed separately (not grouped with machine cables) – plugs properly inserted into sockets – all ‘screw type’ cable terminations tightened, ensure no loose cable strands – earthings checked – cable grounding / shields to be correctly clamped – ensure no damage has occurred during installation

NOTE: Ensure that all covers are closed after installation. 1078933.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly installed shaft top electrification causes: – equipment (SEP, drive etc.) not installed to layout drawing position will interfere with required running clearance from ropes or car – accessories (EBD etc.) not installed to layout drawing position will interfere with required safety spaces, running clearances Incorrectly installed shaft top cabling causes: – incorrectly routed encoder cable can cause poor encoder reference feedback due to magnetic field disturbances from machine cables. This leads to poor ride comfort and drive faults – plugs not inserted correctly to sockets can cause unnecessary disconnections – earthing / shield clamps not used correctly will NOT provide the required grounding to remove signal interference – loose ‘screw type’ terminals cause unnecessary disconnections

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist, manual chain hoist (500 kg) Hand tools needed: Tape measure, spirit level, pencil, hammer drill, hammer, side cutters, 2 x spanner (10 mm), ratchet + socket (19 mm, EBD), spanner (17, 19 mm), allen keys, spanner (7 mm), 2 x spanner (8 mm), electrical terminal screwdriver, multigrip pliers 5S Installation Progress Report Lift Controller Installed QD-181.211 QD 7 commenced

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

195 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

WARNING: During electrification work the power must be off. Ensure that the power to the main supply cable cannot be turned on. Remove fuses and lock the main switches. Notice the separate lighting supplies. For more information, see AM-01.03.002.

WARNING: RISK OF ELECTRIC SHOCK If the yellow DANGER led does not illuminate, when the main power is ON, do not open the drive module. Switch OFF the main switch (220). Lock and tag. Wait for 5 minutes. Continue the work with special caution! Add a warning sign on the cover of the module. Inform your supervisor. > 50 VDC

Inverter drives usually remain energized for about 5 minutes after the power has been disconnected. DO NOT work on the drive, or hoisting motor until you have verified that this energy has been discharged.

Test equipment must be set to the 1000 VDC range. The test equipment must be checked before and after the test to ensure that it functions correctly.

CAUTION: When drilling above drive, SEP or MAP, protect the panels from dust.

CAUTION: If there is a danger of condensed water, on the wire or cable surface, to enter electrical components or connectors in the elevator shaft, form a loop before the cable entry or connector. This cable loop method is recommended for all installations and mandatory in wet/humid operating conditions.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

196 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

CAUTION: When installing the machine cables o E ensure the following things: 90 Encoder and thermistor cables must be separated from motor supply and brake control cables. Otherwise there might be disturbances 100mm in the encoder signals. These cables can cross each other at an angle of 90 degrees. If these cables are routed 1 parallel, the minimum clearance between two 4 cable groups must be 100 mm. 1 = encoder cable, 2 = brake control cable, 3 = motor cable, 4 = thermistor cable

2 3

NOTE: Leave sufficient cable length to allow the SEP and drive panels to be moved from behind the ropes to the maintenance position.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

197 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

20.1

Overview (KDM40) 1. Machine 2. Drive panel 3. KDA module 4. Shaft electrification panel, (SEP) 5. Maintenance access panel (MAP) 6. Car 7. Customer cables: – main supply cable – lighting supply (if applicable) 8. Travelling cables 9. Motor supply 10. Motor connections – brake supply – thermistors – encoder 11. Shaft bundle 12. Maintenance access panel connections 13. Elevator shaft lighting

10

1

9 13

2

12

3

5

4 7

12 6

8 11

1077237.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

198 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

20.2

Installing SEP and drive panels, KDA module, brake resistor and trunkings (KDM40)

NOTE: For exact location of the components, see delivery documents. 1. Install the drive panel, KDA module and SEP panel. Wall fixing: Use drilling template when drilling fixing holes for the drive and KDA module. Check the free space for cooling above (200 mm) and on the right hand side (50 mm) of the drive module.

1

1

1

1

2

2

2

2

1077213.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

199 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Fixing with brackets: Adjust the wall fixing brackets so that panels are reachable from the car roof. Check the running clearance between the car and the panels. Check the free space for cooling above (200 mm) and on the right hand side (50 mm) of the drive module.

1080284.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

200 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

2. Install the metal plate trunkings. 3. Install the 2 m piece of trunking beside the drive panel. 4. Install the emergency battery drive unit.

EBD

2

3

1077229.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

201 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

20.3

Machine cables (KDM40)

WARNING: Ensure that the power supply is safely locked off. See AM-01.03.002.

C U V W

U V W

A

V U W

U

XMEN5

V W

U,V,W PE

B

XBR1 XBR2 XT1 1077218.wmf

Cable To drive / KDA module Thermistor cable XT1 Machine supply cable (note phases, A = right handed, B = left handed) U, V, W, PE Brake cable XBR1, XBR2 Encoder cable XMEN5 Use delivered adapter rings at machine supply cable entry (C). Do not tighten the entry nuts outside the drive panel, use tightening tool inside the drive panel. Check that all connections are clean and clamps are secure.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

202 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

20.4

Cabling: MAP - KDA module, SEP - KDA module (KDM40)

XL5 XW1 XD5 XLG1 L1,L2,L3 PE XBAT1

XL6

XD1

T1,T2, T3,PE X4 XM14 XD1

1077227.wmf

Cable Supply cable Speed information cable LWD cable Cable Safety chain cable Battery backup cable LCE cable

From MAP T1, T2, T3, PE XL6 XL5

To KDA module L1, L2, L3, PE XLG1 XW1

From SEP

To KDA module

XD1 XM14 X4

XD5 XBAT1 XD1

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

203 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

20.5

Cabling: KDA - drive module

X4 XMEN1

X6 X7

L1,L2,L3 X8 1 X20 PE

5

2

6

4 3 1077228.wmf

Cable

No.

From KDA module Power supply cable 1 201/1,3,5,PE Signal cable 2 KDA/XD4 3 DCBG/XEIN1 4 DCBG/XRS1 DCBG/XAP1 Main contactor control 5 KDA 201:1/13 and XRD/1 DC link charge 6 KDA F298/1 and 3 NOTE: KDA ends of cables are pre-connected

To Drive L1,L2,L3,PE 367 I/O board/X4 367 I/O board/XMEN1 367 I/O board/X6 367 I/O board/X7 367 I/O board/X8 385/X20

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

204 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21

CABLES: SEP-MAP, MAIN SUPPLY, KRM

Quality Requirements: Cables – routed and connected according to the AM, free of obstruction – plugs properly inserted into sockets – all ‘screw clamp’ type cable terminations must be checked for correct tightness – all ‘screw type’ cable terminations tightened, ensure no loose cable strands – earthings checked – cable grounding / shields to be correctly clamped – check for evidence of damage

1076669.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly installed / routed cables causes: – obstruction for moving parts (doors, car etc.) – obstruction for MAP interface users – plugs not inserted correctly to sockets can cause unnecessary disconnections – damaged cables can cause intermittent faults – loose ‘screw type’ terminals cause unnecessary disconnections

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist Hand tools needed: Tape measure, spirit level, pencil, hammer drill, hammer, side cutters, electrical terminal screwdriver 5S Installation Progress Report N/A QD-181.211 N/A

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

205 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21.1

Installing load weighing sensor, OSG cables and topmost lighting unit 1. Route fix and connect the load weighing sensor cable (140) and overspeed governor cable (127). Leave minimum 100 mm space between the cables when they are parallel to each other. 2. Install the topmost (halogen) lighting unit. Route and connect the lighting cable (157). Note: In high headroom situations, light unit must be accessible from the car top.

KDL16S

XLG1

KDM

XW1 1079279.wmf

Cable LWD cable LWD cable (in case of VDI)

From Load weighing device Load weighing device / VTC board

OSG cable Lighting cable

Overspeed governor Shaft light

To MAP / LOP-CB / XL4 KDA module / XW1 (KDM) KDL16S drive / XLG1 MAP / LOP-230 / XLH6 MAP / H157

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

206 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21.2

Wiring between SEP and MAP 1. Route and connect cables between the SEP and the MAP. Tie excess cables (coming from bottom of the MAP) behind the toe guard of the topmost landing door.

XM5 X1 XL1 LCEREC

**

XL1

*

274

XM5 LCECPU

XM3 XH2

LCE230

XM7 T1,T2 XLH2 XLH1 XLH8

1076583.wmf

From SEP LCEREC / X1 LCEREC / XM5 LCECPU / XL1 LCEADO / XM5 LCEADO / XM3, XH2 LCEADO / XM7, earthing terminal

To MAP 220 / T1, T2 LOP230 / XLH1 LOP-CB / XL1 LOP230 / XLH2 LOP230 / XLH8 274

*) Place plastic bush over the cable entry **) IVC (in case of VDI) Segmented shaft module

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

207 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21.3

Connecting main supply cable to MAP

WARNING: Do not connect or disconnect any connectors when the power is on. 1. Check that the main switch is switched and locked off. 2. Route and connect the main supply cable. 3. Lock off the main switch (220).

1076590.wmf

21.4

Options

21.4.1

Remote alarm connections 1. Connect the remote alarm output cable to LCERAL / XM30 in the MAP. 2. Check the required alarm method. Set the required alarm transfer delay using potentiometer S2. 3. If required, inhibit the remote alarm by setting switch S1 to OFF position. 4. Test and reset. S1 = Alarm ON/OFF switch S2 = Alarm delay time potentiometer S3 = Reset alarm

NOTE: For more information on remote alarm options, see delivery documents.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

208 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21.4.2

Connections to LCEOPT board (SEP) 1. Route and connect all the cables to the LCEOPT board in SEP.

External input FID fire detection External FRD firemen’s drive External OSS out of service switch

Connector Note For the correct pins, see Remove the jumpers circuit diagrams. when connecting the cables. Potential free only.

External output FRD firemen’s drive return FRD firemen’s drive service EPD emergency power drive mode EPD emergency power drive running EPD emergency power drive returned OSS out of service indication DAL-GP disturbance alarm Cables from landings FRD firemen’s drive switch

Connector X1 X2 X3 X3 X4 X5 Connector

Note X5 Remove the jumpers For the correct pins, see when connecting the circuit diagrams. cable.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

209 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21.5

Group connections

21.5.1

LEDs on LCEGTW board (SEP)

LED

Function when LED is on

Normal status LIFT 24 V OK 24 VDC supply from elevator is OK On GROUP 24 V OK 24 VDC supply from other elevator is OK On LIFT FAIL Communication towards elevator CPU is not working properly Off GROUP FAIL Communication towards other elevator is not working properly Off

Colour Green Green Red Red

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

210 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21.5.2

Group elevator wiring (without segmented shaft power supply) 1. Switch the power off in each SEP. 2. Connect the group cables (XG1A-XG1B, XG3A-XG3B) and the end resistors. For order of the SEP panels, see delivery documents. 3. Switch the power on in each SEP. 4. Check that GROUP 24 V OK LEDs are lit.

XG3B

1. SEP

XG3B

2. SEP

XG3A

XG3A

XG1B

XG1B

XG1A

XG1A

LCEGTW

LCEGTW

*) 1007548-1.wmf

*) Option (duplex advanced), see delivery documents. Check also the end resistor positions.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

211 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

21.5.3

Group elevator wiring (with segmented shaft power supply) 1. Switch the power off in each SEP. 2. Connect the group cables (XG1A-XG1B, XG3A-XG3B) and the end resistors. For order of the SEP panels, see delivery documents. 3. Switch the power on in each SEP. 4. Check that GROUP 24 V OK LEDs are lit.

LCECPU561 XG3B

XG3B

XG3B

XG3A

XG3A

XG3A

XG1A

XG1A XG1B

XG1B

LCEGTWO

1078878.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

212 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

22

INSTALLING TRAVELLING CABLES

Quality Requirements: Travelling cables – installed according to instruction (400 mm loop) – cable markings (text) towards shaft wall – plugs properly inserted into sockets, cable terminations tightened, earthings checked – cables not under strain – excess travelling cable to be correctly stored under the car, NOT tied to the travelling cable loop

* 1010388.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly installed travelling cables causes: – excessive strain to cables and unnecessary disconnections – incorrect running loop / height can cause potential snagging and damage to the travelling cables on guide brackets and by rubbing on the shaft wall – incorrect running loop (text towards car) can cause broken wires inside the travelling cables

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist, unwinding tool Hand tools needed: Phillips screwdriver, side cutters 5S Installation Progress Report N/A QD-181.211 N/A

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

213 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

22.1

Installing travelling cables 1. Connect travelling cables to the SEP (marking XC = SEP side connectors). 2. Fasten the travelling cables to the hanger. Writing* on the cable must face the shaft wall. 3. Lower the travelling cables to the pit as a loop. Move them over the car sill and further to the other side of the car. Ensure that the cables do not get twisted. 4. Secure the cables temporarily to the car top balustrade.

XC11 XC12

LCECPU

1007445.wmf

XC3 XC4 XC1

LCE230

* 1010388.wmf

1078883.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

214 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

23

ELEVATOR SHAFT WIRING

Quality Requirements: Elevator shaft lighting – installed according to layout drawing Shaft bundle – installed and connected – ensure LCEFCB jumper is set correctly (single entrance or TTC) – ensure end of line resistor is in place Landing toe guards – installed at each landing – fixed securely in vertical plane (to prevent obstruction to car door coupler)

1076670.wmf

!!! CAUTION - issues that affect reliability !!!

5S

Incorrectly installed shaft lighting causes: – inadequate lighting levels

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Incorrectly installed shaft bundle causes: – plugs not inserted correctly to sockets or cables under strain can cause unnecessary disconnections

Method tools needed: Man riding hoist, telescopic support pole from plumbing jig

Incorrectly installed landing toe guards causes: – interference / damage to the car door coupler

Hand tools needed: Tape measure, pencil, spirit level, hammer drill, hammer, pliers, Phillips screwdriver, battery drill / driver, side cutters 5S Installation Progress Report N/A QD-181.211 N/A

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

215 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

WARNING: During electrification work the power must be off. Ensure that the power to the main supply cable cannot be turned on. Remove fuses and lock the main switches. Notice the separate lighting supplies.

NOTE: This section describes the shaft wiring without trunking. For more information on elevator shaft wiring with trunking, see APPENDIX E. Elevator shaft wiring with trunking.

23.1

Shaft lighting

max 0.5m

1. Install the elevator shaft lighting. Install the light units to horizontal position (if possible) with the lamps pointing downwards. Install the lowest light unit to vertical position. Note: In high headroom situations, topmost light unit must be accessible from the car top. 2. Drill holes for signalling cable and door lock cable fixings at each landing.

6m

2 50

mm

6m

0.5m

1027379.wmf

max. 0.5m

6m

1078679.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

216 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

23.2

Installing shaft wiring

NOTE: For more information on elevator shaft wiring without trunking, see AM-10.60.028. For more information on elevator shaft wiring with trunking, see APPENDIX E. For more information on segmented shaft network, see section 23.4. For the correct location of the shaft bundle, see the elevator layout drawings. 1. Install the connection and protection boxes. Do not drill through the holes on the box. Fix the flat cables with wall plugs between the connection and protection boxes. 2. Connect the safety chain wires to MAP and signalization and alarm bell cables to SEP.

XLH4 XLH7 XH11 XH12

1076661.wmf

Cable Landing door contact (P122) / landing door lock contact Tension weight contact / stop switch in the pit Alarm bell cable Signalling cable (LCEFCB)

To SEP / LOP230 / XLH7 SEP / LOP230 / XLH4 MAP / LCECPU / XH11 MAP / LCECPU / XH12

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

217 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

23.3

Wiring at the landings 1. Connect the landing door lock cables (E) and DOM contact cables (F, optional). D = dual entrance connection. 2. Connect the signalization cables. Leave 100 mm free cable ends at the landing side. 3. Connect optional devices** (alarm bell, fireman’s drive, key switch, locking of landing calls, potential free contact, water sensor contact). 4. Secure signalling cable (at 1 m distances) and any extra cable lengths** to the flat cable. 5. If more than 8 floors, connect another flat cable(s)*. 6. Through type elevator: Check jumper X1 position. Left (A) = front side door, right (B) = rear side door.

F

E

E

D

** * X1

A

B 1076665.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

218 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

23.4

Installing segmented shaft network (if 16 served floors / group elevator)

NOTE: Segmented shaft network is used when there are more than 16 served floors (including rear side served floors with through-type car). It feeds operating power for the chain of FCB boards and signalization devices. Note that the control cabinet feeds power to the first 16 served floors. 1. Split shaft network so that number of served floors in each segment is about equal. No segment can have more than 16 served floors. 2. Connect the termination resistor (TX+ / TX-) in the lowest shaft network module. 3. Connect the termination resistor to the lowest LCEFCB/FOB board.

262:1/2

N

20 19

LCEFCB/LCEFOB

11 10 2 XS1

1

XS2 TX+ TX-

XS2 1077302.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

219 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

23.5

Installing support channel (optional) 1. If elevator with dividing beams or steel elevator shaft, use support channels to install the shaft wiring components.

1068996.wmf

1068886.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

220 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

24

ELECTRIFICATION IN THE PIT

Quality Requirements: Travelling cable – not twisted – cable markings (text) towards shaft wall – installed according to instruction (400 mm loop) – loops hang freely at the correct height (car on buffers) • outer loop = 150 mm from pit floor • inner loop = 100 mm from outer loop Pit wiring – electrification cables routed to avoid cable damage or tripping hazards – stop switch(es) must be installed to correct position (within easy reach of lowest floor and pit) Pit toe guard (side opening door cases) – installed to comply with EN81:1 clause 5.7.3.3 b (code reason = in cases where distance from car toe guard to front wall exceeds 150 mm) – also in rear side for TTC cases 1076648.wmf

Car bottom shoe adjustment – ensure car shoe DBG gap is 1mm each shoe

!!! CAUTION - issues that affect reliability !!! Incorrectly installed travelling cables causes: – excessive strain to cables and unnecessary disconnections – incorrect running loop / height can cause potential snagging and damage to the travelling cables on guide brackets and by rubbing on the shaft wall – incorrect running loop (text towards car) can cause broken wires inside the travelling cables Incorrectly installed pit wiring causes: – plugs not inserted correctly to sockets can cause unnecessary disconnections – incorrectly routed / secured cables in the pit can cause potential tripping hazards and damaged to the cables

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist + ASGT Hand tools needed: Tape measure, spanner (19 mm), pencil, hammer drill, hammer, sprit level, Phillips screwdriver, side cutters, battery drill / driver 5S Installation Progress Report Shaft Wiring Complete

WARNING: If Fire Fighting elevator, ensure that the pit electrification height is according to local code requirements QD-181.211 to prevent water ingress. IP Rating of enclosures must be in N/A accordance with local codes, check delivery documentation.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

221 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

24.1

Finalizing car installation 1. Position the car to have safe access to the pit. Engage the safety gear. 2. Fix the floor to the bottom beam. Remove the buffer extensions one at a time to access the fixing bolts. NOTE: Safety space MUST be maintained at ALL times! 3. Adjust the gap between car guide rails and car guide shoes to 1 mm. Shim as necessary. 4. Install the travelling cable hanger. 5. Install the compensation chain hanger (if applicable). 6. Install the ballast weights (if applicable) approximately centrally. 7. Tighten all the lowest wall fixing bolts.

3

1mm

1mm

3 4

5

2

6

7

1077617.wmf

Improved detail required how to install DRAFT these to the car, especially to suit the Copyright ©2012 KONE Corporation All rights reserved.

updated sill profile (Not clamped, just AM-01.01.250 on!)

222 (340) hooked

(Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

24.2

Installing electrification under the car

=

=

1. Position the car so that there is safe access to the pit. Engage the safety gear. 2. Fix the travelling cables to the hanger under the car. Adjust the travelling cable loops according to the distance between the car and the car buffers.

400mm

100mm 150mm 1010076-1.wmf

1027312.wmf

3. Fasten the excess cable length (if any) to the car floor. 4. Lift the safety gear switch cable to car roof. Use car bottom alarm button as lift rope. 5. Install the car bottom alarm button to the travelling cable hanger.

1007475.wmf

1007474.wmf

Please update this bracket type to the new version shown on the previous page

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

223 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

24.3

Installing pit electrification

WARNING: Check that the car is safely locked off and can not move.

NOTE: For more information on elevator shaft wiring with trunking, see APPENDIX E. Elevator shaft wiring with trunking. 1. Install a 500 mm piece of trunking (*). 2. Install the lowest shaft lighting unit, lighting switch, pit stop switch and intercom socket. The pit stop switch must be reachable from the pit and from the landing. 3. Connect the pit cables (OSG tension weight contact, pit stop switch, shaft lighting, intercom socket, oil buffer contacts (if any) and any additional pit devices). 4. Check that an end connector is connected to the XS2 in the lowest board.

XS2

*

1076649.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

224 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

24.4

Installing pit toe guard 1. Install the pit toe guard (also for C-side if through type car). The lower end of the toe guard must touch the pit floor.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

225 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25

CAR ELECTRIFICATION

Quality Requirements: Car electrification – electrification routed to avoid cable damage or tripping hazards – plugs properly inserted into sockets, earthings checked COL (curtain of light) – installed and aligned – RX unit NOT installed to slam post side on side opening doors Limit switch ramps – positioned to activate the final limit switch 40...60 mm beyond terminal floor and break contact BEFORE car or CWT contacts buffer Magnets – correctly positioned – edge of position switch horizontally within 5...10 mm of face of magnet

1011161.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly installed car wiring / electrification causes: – plugs not inserted correctly to sockets can cause unnecessary disconnections – incorrectly routed / secured cables on the car can cause potential tripping hazards and the cables can be damaged leading to exposed hazardous voltages and potentially hazardous short circuit situations Incorrectly installed COL causes: – unwanted activation failures from misaligned units – COL RX (receiver unit) installed to slam post side will cause unwanted activation from light sources on landings Incorrectly adjusted limit switch ramps causes: – unwanted crash stopping from slight overtravel – car / CWT striking buffers

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist + ASGT Hand tools needed: Battery drill / driver, Phillips screwdriver, side cutters, 2 x spanner (8, 10, 13 mm), spanner (19 mm), pliers, allen keys, tape measure, spirit level, hacksaw (if required to cut door operator bracket) 5S Installation Progress Report Lift Car Wired QD-181.211 QD 7 continued

Incorrectly adjusted magnets / switches causes: – poor levelling accuracy – unwanted re-levelling activations – loss of elevator position / crash stopping drive faults

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

226 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.1

Magnet switches

NOTE: Clear the unnecessary tools and materials from the car roof. Check the location and number of the car roof devices in the delivery documents. The main principle is shown in the layout picture. Switch 61:U and 61:N Car position switches 30 Door zone switch, front side B30 Door zone switch, rear side 77:U Deceleration switch upwards 77:N Deceleration switch, downwards 77:S Synchronisation switch (if 77:N is not between two lowest floors or if 77:U is not between two topmost floors)

Magnet strip and number 120 mm magnet for each level

Magnet fixing Single car guide rail

270 mm magnet for each front door 270 mm magnet for each rear door 80 mm magnet at the top part of the elevator shaft 80 mm magnet at the bottom part of the elevator shaft 80 mm magnet between the lowest and second lowest floor, 80 mm magnet between the topmost and second topmost floor

Machine side car guide rail Separate bracket on the counterweight guide rail Single car guide rail

1. 2. 3. 4. 5.

Shaft bundle Trap door contact (option) Car top connection box Door operator Photo cell amplifier / COL amplifier 6. Travelling cable

Machine side car guide rail Separate bracket on the counterweight guide rail

B30 77:S 2 30

61:U, 61:N 77:U

77:N 3

CAUTION: Note the positions of 77:U and 77:N to ensure the clearance for the safety gear passing the magnets.

4

5

6

1

1077566.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

227 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.2

Installing car top connection box

CAUTION: Use only short screws delivered with the car to install components on the plywood roof. 1. Secure the travelling cables to the kick plate. Length of the larger cable inside the car top connection box is 440 mm, smaller cable 380 mm. 2. Install the car top connection box on front side of the car, opposite to the machine. Do not drill any through holes on the plywood roof. 3. Connect the travelling cables, see markings on the plugs. Connect earth wires to the earth bar, check the connection tightness.

LCECCB XT3 XT1

XT4

XT2

1078752.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

228 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.2.1

Connectors on LCECCB board LCECCB board

XB1 - Final limit switch 51 XB2 - Safety gear contact 52 XB3 - Inspection station 42 XB4 - Rear door button B41 XB5 - Safety lock 63 XB6 - Trap door 57 XB7 - Door contact front side 87 XB8 - Door contact rear side B87 XB11 - Insulation test XB12 - Inspection station 24 VDC signals 42 XB13 - 230 VAC plug 45 XB14 - Car light 44 XB15 - Car ventilation 43 XB16 - Front door power supply XB17 - Rear door power supply XB18 - To Car Operating Panel XB21 - Door zone switch front side 30 XB22 - Car position switch upwards 61:U XB23 - Car position switch downwards 61:N XB24 - Door zone switch rear side B30 XB25 - Deceleration switch, upwards 77:U XB26 - Deceleration switch, downwards 77:N XB27 - Synchronisation switch 77:S XB28 - Door operator front side 84 XB29 - Photocell front side 90 XB30 - Door operator rear side B84 XB31 - Photocell rear side B90 XB32 - Battery 227 XB33 - KoneXion XB34 - Emergency lighting for car roof XB35 - Alarm bell 65 XT1, XT2, XT3, XT4 - Travelling cables

P1

XB21

30 XB22

61U

FAIL

24V OK

L3

L1

XB1 L8

L11

L2

BATTERY FUSE F2 OK

L12

INSULATION TEST

XB23

61N

BATTERY OK

L13

51 XB11 XB2 XB12

XB24

B30

L14

77U

L15

77N

L16

77S

L17

24 V

XB25

XB3

XB13

230 V

XB26

45

XB27 XB28

52 42

LIGHT

42 230V XB14

44

XB4 XB15 B41

84

A DOOR

FAN

43

XB29

XB5 XB16

90

A PHOTOCELL

63

DOOR A

XB30

230V XB6

XB17

B84

B DOOR

DOOR B 230V

XB31

57

B90

XB7

B PHOTOCELL XB32

LCECCB

227

BATTERY XB34

713713 H05

87

44:2

EM. LIGHT XB35

XB8 XB18

65

ALARM BELL XT1

XT3

XT4

B87

COP XT2

XB33

XB9

KONEXION 1010458.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

229 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.3

Installing electrification on the car roof

CAUTION: Handle the switches with care.

NOTE: To prevent tripping hazard, route the cables along the kick plates and the channel on top of the structural ring. Tie them using cable ties. 1. Install the switches and oil lubricators (1). Connect the cables. 2. Set the distance between the 61:U and 61:N to 130 mm to ensure the correct levelling. 3. Route and connect the safety gear contact, car bottom alarm button, COP, trap door contact (if any), blocking device and all other possible safety chain cables. 4. Route and connect the ventilation, car lighting and all the optional cables. 5. Install the KONEXION equipment. For more information, see appendices. 6. Route and connect the cable of the second COP (if any) to the normal COP.

B30 77:S 1 61:U 77:U 51 61:N

77:N

30 1077554.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

230 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.4

Install the provision for lift announcer

CAUTION: Use only short screws delivered with the car to install components on the plywood roof. 1. Install the LCEOPT board in plastic box on the car roof. For more information, see delivery documents. 2. Route and connect the cable from COP to LCEOPT board.

25.5

Install the intercom socket on the car roof

CAUTION: Use only short screws delivered with the car to install components on the plywood roof. 1. Install the intercom socket to the car roof. 2. Route and connect the cable to XB9 on the LCECCB board at the car top connection box. For more information, see delivery documents.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

231 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.6

Installing curtain of light For more information on installing curtain of light, see AM-03.17.011.

25.6.1

Fixing curtain of light

CAUTION: Side opening doors: Install the transmitter TX at the slam post side. Otherwise the car or lobby lighting may interfere and cause a fault operation in the curtain.

Action Fix both detector parts (the transmitter TX and the receiver RX) to the opposite ends of the sill. Railing 1:

Note For railing type 2 when LL=700, 750 or 850 mm, cut off a piece from the fixing bracket.

HH+254

Step 1

5 94.5

2 0 +1 L L

CL

1

TX 1064076.wmf

1. Buffer 2. Fixing for side opening door

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

232 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Step Action Railing 2, centre opening door:

LL=900...1100

5

LL=700...850

Note

64.5

LL+8 / LL+15

+8 LL

LL

CL

5 +1

CL

1011159.wmf

Railing 2, side opening door:

LL=900...1100 9

LL=700...850

5

CL

64.5

LL+5

1011160.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

233 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Step 2

Action Adjust the detectors in vertical position in both directions.

Note

HL= 2100mm

6mm

HL= 2000mm

1011161.wmf

1

1027471.wmf

1041530.wmf

4

Check the running clearance of the detectors at each landing. Inspect the running clearance visually at top and bottom of the shaft.

Minimum running clearance: – 10 mm to landing door – 25 mm to wall

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

234 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.6.2

Routing the cables of the curtain of light

Centre opening door

2

1. Cable tie 2. Cable behind the operator

1

1011168.wmf

Step 1

Action Route the cables to the car roof.

2

Fix the cables properly using cable ties. Fixing accessories are supplied in the plastic bag.

Note Avoid tight bends and sharp edges. Do not over tighten the cable fixings. Ensure that cables do not hit any moving objects (for example door panels, landing doors)

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

235 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.6.3

Connecting the cables Step 1

Action Connect the cables direct to the terminals in the door operator board.

Note 1. Drive 1 2. Drive 2 3. Car 4. Transmitter 5. Receiver

45 44

X15

46 49 47

X16 X16

48

1

X15

2 3 4

5 X15

TX

X16

RX 101119

2

Set the DIP switches. 1. Receiver lens 2. Pos. 1. Overconnection of single beam 3. Pos. 2. Set this to ON

1 3 2

on

off

on

off 1011174.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

236 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.7

Installing ramps and magnets (driving up)

NOTE: For correct locations of ramps and magnets, see shaft vane diagrams. 1. Fit the limit switch ramps. The switch must start to operate 40...60 mm below the lowest floor and 40...60 mm above the top floor. Electrical contacts must break before the buffer. 2. Place magnets for 61:N, 61:U and 30 (B30). A = floor level, B = bottom ends at the same level 3. Place magnets for 77:U and 77:N (white mark of the lower magnet upwards, upper magnet downwards). The magnet must be minimum 100 mm from a bolt or guide rail clip. Raise/lower as necessary, horizontally in front of the switch (narrow detection area). 4. Optional: Place magnets for 77:S, dummy floors (floor to floor distance > 5 m) and 61 magnets for each 5 metre (at equal distances).

1

77:S B30

3

2

4

77:S

*

**

77:U

30

61:N

**

B

5...10 mm

77:S

77:N

*

=

A

=

61:U

1077731.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

237 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

25.8

Wiring of door operator and curtain of light (or photo cell) Step 1

25.9

Action Connect the cables on the operator and route the cables outside of the kick plates to the car top connection box. Secure the cables with cable ties.

Note Refer to the layout drawing.

Installing car emergency light 1. Install the car emergency light to the car lintel. 2. Route and connect the cable to the car top connection box.

Can we have a picture of the emergency light being installed to the lintel here?

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

238 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26

FINALIZING LANDING DOORS

Quality Requirements: NOTE: These instructions are for installing KES 201 landing doors. Fire proofing materials – installed Carpet profile – installed and aligned, no tripping hazards Quality check performed – inspect for any sharp edges and de-burr if necessary – no scratches or dents – no abnormal noises, normal noise level at 1 m distance from moving door: • normal = max 55 dB(A) • impulse (e.g. reopening) = max 60 dB(A)

!!! CAUTION - issues that affect reliability !!! Incorrectly installed fire proofing materials causes: – contact with doors causing damage to fire proofing materials and doors Incorrectly installed carpet profiles causes: – tripping hazards – contact with doors which prevents smooth running Scratches or dents to doors causes: – poor visual appearance – handover rejection by the customer

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist Hand tools needed: 2 x spanner (8 mm), spanner (15, 16 mm), hammer drill, hammer, battery drill / driver, metal cutting shears, tape measure, spirit level 5S Installation Progress Report Doors and Frames Installed 100% QD-181.211 QD 6 completed

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

239 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.1

Uprights on slampost side (fire rated EI30/EI60/EI120-W doors)

2 4

1 3

5 6 4

Step 1 2

3

Action Install the 4 M5 bolts (1) to the slampost stiffener brackets (2) using the nut (3). Fit the insulation material (4) on the stiffener brackets.

Note

Always use gloves, protect your arms and wear dust masks when handling the insulation material.

Secure the insulation material with big washers and nuts (5)(6).

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

240 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.2

Uprights on non-slampost side

26.2.1

Frame door (fire rated EI30/EI60/W)

Step 1 2 3

4

Action Cut the small 150mm wide hard rockwool plate into 4 pieces of 50 x 150mm strips (2). Fit the strips evenly devided into the upright. Apply 4 springs (3) to the hard rockwool (1).

Slide the hard rockwool plate under the top track bracket and over the strips.

Note Always use gloves, protect your arms and wear dust masks when handling the rockwool. The spring height has to match the 4 pieces of strips in the upright. Shorten the hard rock wool plate so that it fits into the upright.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

241 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.2.2

Frame door (fire rated EI120)

A

B

el120_h.wmf

Step 1

Action Install 2 insulation material blocks in the upright.

2

Apply 4 springs to the blocks.

Note The blocks have to be installed with the expanding seal (A) positioned like in the picture and the thin layer (B) in the centre part of the upright. Apply 2 springs for each block.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

242 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.2.3

Front door (fire rated EI30/EI60)

Step 1 2

3 4 5 6

Action Note Install the brackets (1) to the upright flange. Cut the small 150 mm wide hard Always use gloves, protect your arms rockwool plate into 4 pieces of 50 x 150 and wear dust masks when handling the mm strips (2). rockwool. Fit the strips evenly devided into the upright. Apply 4 springs (3) to the hard rockwool The spring height has to match the 4 plate (4). pieces of strips in the upright. Slide the hard rockwool plate under the Shorten the hard rock wool plate so that top track bracket and over the strips. it fits into the upright. Bend the brackets (1) to keep the hard rockwool plate in position.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

243 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.3

Fire trims (frame version only)

26.3.1

Sheet metal

vertical fire trim

horizontal fire trim

vertical fire trim

Step 1 2

3

Action Fix the vertical fire trims to the door frame using self-drilling screws. Bend the straight fire trim back against the wall to close the wall gap. The fire trims must overlap the rockwool on the “non slampost” side. Fix the fire trims to the wall using nail anchors.

Note

The corner cut out in the fire trim is for the top track bracket. The trim edge holds the rockwool in position.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

244 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.3.2

Soft adhesive

el120_d.wmf

Step 1 2

Action Open the package and cut 1.5 m long stripe. Cut the remaining part in half.

Note

1 .5

m

=

= el120_f.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

245 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Step 3

Action Clean the wall surface from the dust.

4

Glue the short stripe horizontally on the top of the door and the wall. Glue the long stripes vertically to the both side of the door.

5

Note

ei120_c.wmf

6 7 8

Install 3 flat brackets to both uprights with self drilling screws. Bend them against the wall. Fix them to the wall with anchor nails.

el120_e.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

246 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.4

Corner angles and wall gaps 1.

2.

2.

a1125dl.wmf

Step 1

2

26.5

Action Note Fit the front side extension panel corner Only for front version. angles to the shaft wall using nail Match the slots in the corner angles and anchors. the holes in the side extension panel. Fix the corner angles to the side panels using self drilling screws. Fill the wall gaps of the frame and front version doors with the soft rock wool blocks to comply with required fire ratings.

Top extension panel fire insulation (front version only) Always use gloves, protect your arms and wear dust masks when handling the rockwool. 2.

Step 1 2 3

3.

2.

Action Note Cut holes in the hard rockwool plate for the top fixing profiles. Fasten the hard rockwool panel to the horizontal beam using annealing wire and washers. Fill the top pocket with two soft rockwool slabs.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

247 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

26.6

Carpet profile

a31265xc

Step 1 2

3

26.7

Action Clip the carpet profile over to the landing sill. Use silicone or other suitable filler to close the gaps between the floor and the carpet profile. If needed, knock the uprights evenly to close the gap between the uprights and the carpet profile.

Note Do not fit this before the floor finish is installed as the profile is not removable. Use extra screws to fix the carpet profile to the landing floor if the floor is exceptionally curved.

Quality check Step 1

2

3

Action Check the operation and appearance of all doors. For more detailed door quality information refer to the AMD Maintenance Standard AS-03.12.036. Make sure there are no dents, scratches or abnormal noises. Normal noise level: from door: 1 metre from landing: 1 metre speed level: 1 (normal) Door moving: max. 55 dB(A) Impulse (e.g. reopening): max. 60 dB(A) Ensure the emergency key works properly.

Note

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

248 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27

ROPING

Quality Requirements: Ropes – lubrication level checked – rope lengths and equal tensioning checked – lock nuts tightened, split pins installed – lock nuts not leaning against split pins – rope guards adjusted – rope labels retained and stored in the MAP for future reference Compensation chains (if any) – chain length checked – no twists, runs free of obstructions Car toe guard – fixed securely in vertical plane (to prevent obstruction to landing door rollers) Manual brake release cable – routed to prevent obstructions and contact with car or landing doors – correct type and number of fixings used – bending radius > 100 mm – adjusted to ensure brake operation

1077505.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly lubricated / tensioned ropes causes: – extremely premature rope wear / replacement – extremely premature machine sheave wear / replacement Incorrectly adjusted rope terminations causes: – noise, vibration and poor ride comfort Incorrectly adjusted rope guards causes: – gap too small = rope(s) rubbing guard , noise / vibration, poor ride comfort and premature rope wear / replacement – gap too big = potential loss of rope from pulley! Incorrectly installed car toe guard causes: – can cause interference / damage to the landing lock rollers Incorrectly installed / adjusted brake release cable causes: – obstruction with moving parts / damage to cable – adjusted too slack = unable to manually operate brakes – adjusted too tight = potential brake malfunctions

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Man riding hoist + ASGT, unwinding tool, work stool, 2 x telescopic support pole from plumbing jig, pulling rope, brake opening bolts (temporary, with delivery), telescopic pole, site trolley, rope clamp Hand tools needed: Tape measure, 2 x spanner (8, 13, 19 mm), spanner (10, 18 mm), side cutters, knife, ratchet + socket (13 mm), allen key (6 mm), spirit level, hammer drill, battery drill / driver, insulating tape, pliers, 2 x G-clamps 5S Installation Progress Report Roping Complete QD-181.211 QD 7 commenced

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

249 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.1

Lubrication of suspension ropes Elevator suspension ropes are lubricated completely during the manufacturing process. However, long storage and installation times may reduce the effectiveness of lubricant applied in manufacturing of the suspension ropes. Hence, re-lubrication already before commissioning of the elevator may be required to guarantee the full service life of ropes, machinery traction sheave and other rope pulleys. There are five reasons for rope lubrication: 1. 2. 3. 4. 5.

To protect the rope core from deteriorating. To prevent friction between the wires, strands and core. To guard against corrosion. To optimise the position in traction sheave to get best friction. To prevent damaging (wearing) of the traction sheave.

NOTE: It is essential to use correct amount of lubricant, because too little may not protect the rope and too much can result in serious problems. (Frequent light application has given the best results).

WARNING : Overspeed governor ropes must NOT be lubricated.

27.1.1

Determining the lubrication need

CAUTION: No definite time-dependent interval can be given for lubrication. Lubrication need must be checked during new equipment installation because rope storage and installation times can be relatively long. Correctly lubricated rope should stick lightly to the glove when crabbing it by hand. The lubrication of the suspension ropes is required if: – – – –

the ropes are dry or the lubricant has become stiff there is red dust on the ropes or on the floor there is metal dust under sheave or pulleys the grooves of the pulleys are dry (no lubrication film on fingertip when wiping)

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

250 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

CAUTION: If the ropes get dirty during the roping: - Do not clean them with any chemical cleaner, solvent or diluent. - Clean them gently using a brush or rag moistured with rope lubricant.

27.1.2

Lubricants For more information on acceptable lubricants, see AS-01.01.010 - Lubricant recommendation instruction.

27.1.3

Lubricating ropes For more information on lubricating the ropes, see AM-09.01.006.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

251 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.2

Roping principle NMX07

1 4

5

3

1

31

2

23

6

4

12 4

21 43

12 34

4

2

34

2

5

12 5

1 32 4 5

12 34 5

NMX11

31

34 5

6

1 32 4 65

12 34 56

1075348.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

252 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.3

Preparations

500

1. Ensure the access to the pit and to the car roof. 2. Make a pull rope loop round the car. Note the routing between the car guide rails. Lower the rope ends from the car roof, tie them together in the pit. Tidy the rope tails with tape. 3. Use G-clamp for rope guiding.

1075349.wmf

4. Place the remaining counterweight filler weights: •onto the top beam at the car roof (check that the load is on the top beam) OR •inside the car (protect the car interior from any damage).

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

253 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.4

Roping in the pit 1. Pull the suspension rope round the car. Fix the rope to the pull rope with cable ties. 2. Release the rope from behind the G-clamps. Secure the rope to the hand rail. Leave approximately 1.5 m free rope end to ease rope end fixing at top of the shaft. 3. Repeat for the other ropes. Check that each rope end is equally long. 4. Route the suspension ropes round the diverting pulleys below the car. 5. Adjust the rope guards. Ensure that the ropes remain in correct order.

4 2

2

1

3mm

5

5

4 1075358.wmf

27.5

Attaching compensation chain under the car (optional) 1. Attach the compensation chain (if applicable). Expose minimum one free link of the chain.

1078749.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

254 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.6

Roping at top of the elevator shaft 1. Open the machine brakes. Use temporary bolts included in delivery. 2. Fix the car side rope end. The rope ends must be equally long. Fit the rope grips. Tape the rope ends. Check that split pins are included. 3. Route the rope loop round the traction sheave. Lower the loop down to the counterweight. 4. Fix the counterweight side rope end. 5. Route the rope loop round the CWT pulley. Ensure that the ropes remain in correct order.

1

4

1200

2

3

5

3 1075359.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

255 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.7

Shortening the ropes

WARNING: Check that the car is heavier than the counterweight. Remove filler weights one at a time from the counterweight frame to allow car to drive down. 1. Mark and loosen the ASGT rope grips* to prevent safety gear engaging when driving down. Lift the counterweight frame 1350 mm above the pit floor. 2. Install the buffer spacer. 3. Install the oil buffer (if applicable). 4. Lower the counterweight frame slowly onto the telescopic pipes. **In case of deep pit, extend the telescopic pipe length to 2000 mm. Lock with M12 bolts. 1 = piece of fabric 2 = cable tie 3 = G-clamp 4 = timber piece 5. Measure the distance X between the counterweight buffer and the buffer spacer.

4

* 1 2

2 3

1

**

4

5 2000

X

1

3

1077717.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

256 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

6. Calculate the distance Y (from the car sill to the landing sill or between top tracks**). Y=X-A-B-C A = overtravel: 100 mm (see layout) B = rope stretch: •3.75 mm per rope meter (fibre core) •2 mm per rope meter (PAWO F3) •1.83 mm per rope meter (PAWO F7S) C = spring compression: 20 mm 7. Connect the ASGT rope. Adjust rope grips according to marking. 8. Position the car according to calculation Y (car sill below the topmost landing sill). 9. Shorten the ropes at the counterweight side rope fixing one at a time. Do not remove the rope fixings. 10.Fit the rope grips. Cut and tape the rope ends. Check that split pins are included.

**

Y

*

1033741.wmf

Y

1007524.wmf

1033401.wmf

11.Remove the telescopic pipes below the counterweight. 12.Install the counterweight oil lubricators.

1078369.wmf

13.Remove the man riding hoist tension weight.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

257 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.8

Attaching compensation chain to counterweight

 200

1. Cut the compensation chain to correct length. 2. Install the chain to the counterweight. Check that the distance from chain to the pit floor is minimum 200 mm. Check that the chain is not twisted.

1079216.wmf

27.9

Moving OSG rope in the large groove 1. Fit the overspeed governor rope in the large groove. Wear gloves.

1078686.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

258 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.10 Installing brake release cable

WARNING: Cable cover must be free to follow the brake release lever movement without jamming. Minimum cable bend radius is 100 mm. 1. NMX07 machine: Remove the metal sleeve* from the manual brake release cable. NMX11 machine: Do not remove the metal sleeve* from the manual brake release cable. 2. Connect the cable to the machine. Locate the nuts at cable end to middle of the threaded bar to have adjustment tolerance in both directions. 3. Route the cable and pull the slack to the lever end. 4. Mark cable sleeve at position of lever handle sleeve socket. 5. Pull out minimum 300 mm of the wire rope towards the machine end so as not to damage the wire rope. 6. Cut the sleeve and peel back 25 mm of the outer coating. 7. Push the brake release cable back into the sleeve and route into the lever. Note that tightening clamp area and brake cable must have metal contact surfaces for sufficient friction. 8. Adjust the cable tension. The brake levers must be in the centre position.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

259 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction Please remove the 'machine room' type machine from this machine room less manual :-)

5 m 0m ~5

3

NMX07

NMX11

2.2

~50

2.1

6

NMX11

8 7

90º

3

NMX07

1079369.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

260 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.11 Testing manual brake release operation 1. 2. 3. 4.

Pull the lever to brake open position. The cable must release the machine brake. The car must move slowly and stop immediately when the lever is released. The lever must return to the brake closed position by itself. Store the lever inside the MAP.

1076094.wmf

1079301.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

261 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.12 Dismantling man riding hoist from car

WARNING: The car top balustrade must be set according to the layout drawing / EN81-1. 1. Secure the diverting pulley securing rope to second topmost guide rail bracket. Tie the gate of the diverter pulley hook open. 2. Locate the car roof approximately 400 mm above the topmost landing. 3. Close the machine brakes. Roll the hoist rope on the reeler. 4. Connect the hoist hook to the hoist body. Drive the hoist out on the landing. 5. Remove the diverting pulley and securing rope. Work from the landing.

1033388.wmf

1033386.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

262 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.13 Finalizing car installation 1. Install the car toe guard working from the lowest landing. Align vertically with the front edge of the car sill. A = toe guard support, AMDC1 B = toe guard support, AMDC2 2. Install the car fans. Connect to the car top connection box. 3. Check the car balance. Relocate the ballast weights as necessary. 4. Adjust the car top balustrade height according to the local code and layout drawings. 5. Drill a screw to car top balustrade. Hang the OSG resetting stick. Secure with cable tie. 6. Install the document holder to the balustrade.

Move installing car toe guard to section 28.2, can't do this till A car at bottom floor.

B 1077506.wmf

1078759.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

263 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

27.13.1 Installing security ropes

WARNING: Risk of ceiling falling down from lock side. It is mandatory to install the security wires. Install them properly. 1. Route the wires through the holes. *) Emergency opening wire releases the ceiling lock from the car roof (roof with trap door). **) Security wire prevents free fall of the ceiling.

*)

**)

1077278.wmf

2. Fix the emergency opening wires: – route the wire – pull the wire so that the lock latch starts to turn – tighten the wire lock and cut off the extra wire

GACL18nt.wmf

1077279.wmf

Bring all of the ceiling rope references to here.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

264 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

28

COMMISSIONING

Quality Requirements: Prerequisites – shaft components, machine, car, doors and ropes installed – car and shaft electrification (including signalization) installed – positioning magnets installed accurately according to shaft diagram – man riding hoist removed from car – car and CWT balanced – electrification panel covers closed – OSG installed to final position – safety gear and OSG operation checked Commissioning for inspection drive – terminals, connections, earthings, cable routings checked – construction time power supply connected (if required, KDL16S) – construction time power supply earth screw temporary removed (if required, KDM40) – LON protocol performed – drive parameters, dip switches set – motor direction, encoder polarity checked – safety chain checked, RDF and inspection Commissioning for rated speed – LWD adjusted – shaft setup performed – levelling accuracy checked Final steps – car and CWT balanced – CWT screen installed to final position – oil collectors installed Fine adjusting – elevator running to optimum performance

NOTE: If required by your frontline local code, the following tests MUST be performed and verified BEFORE the power is switched on! – Earth Continuity (max value = 0.5 ) – Insulation Resistance to Earth (min value = 1 M)

!!! CAUTION - issues that affect reliability !!!

Poor adjustment of parameters and fine tuning causes: – elevator fails to run to optimum performance – poor ride quality – possibility of drive faults and break downs NOTE: In case of PC board replacement Incorrect storage / handling of PC boards can cause: – component / board damage – component / board failure For more information, see AS-12.02.001.

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: N/A Hand tools needed: Construction time power supply tool (battery & lead), electrical terminal screwdriver, multimeter, spanner (7 mm), 2 x spanner (19), TORX screwdriver (T10), Phillips screwdriver, multigrip pliers, allen keys, thin screwdriver for adjusting potentiometers (LWD), test weights 5S Installation Progress Report Roping Complete QD-181.211 QD 7.1 commenced

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

265 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

28.1

Prerequisites

28.1.1

Health and safety at work Mandatory Observe the requirements of your national Elevator Regulation Code.

Note In case of conflict between the Code and the present commissioning instructions, rely on your Code. Be extremely careful when working with the There are high voltages: electric components and their enclosures. – in the main circuit capacitors (>500 VDC) Refer to AM-01.03.002 Take 5. and on the inverter board – in the safety chain and inside the shaft electrification panel (230-400 VAC) Inverter drives remain energised for about 5 minutes after the power has been disconnected. DO NOT work on the drive, hoisting motor or braking resistors until you have verified that this energy has been discharged. Test equipment must be set to the 1000 V DC range. The test equipment must be checked before and after the test to ensure it functions correctly. While the LED DANGER is ON on the inverter board, there are high voltages in the drive module. When making electrical connections in the Car light is not controlled by the main elevator shaft or in the car, the power must switch 220 in maintenance access panel. be turned OFF from the main switch (220) This circuit has its own switch. and car light supply (262) in maintenance Refer to AM-01.03.002 Take 5. access panel. No personnel are permitted in the elevator shaft during this phase.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

266 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

28.1.2

Prerequisites and preparations Before starting the commissioning, check that the following basic things have been done: Item

Done

Elevator shaft installation. Machine installation. Car installation. Car and landing door installation. Rope installation. Car and elevator shaft electrification including the signalling devices. The positioning magnets are installed accurately according to the shaft diagram. The man riding hoist is removed from the car. Car and counterweight are balanced. Covers of the electrification panels are placed. Overspeed governor is installed to the final position. Safety gear and overspeed governor operation checked.

WARNING: The elevator first run must always be made from the MAP with the car positioned so that there is access to the car roof from the MAP level.

WARNING: No people are allowed to be on car roof.

CAUTION: The hoist must be removed from the car, the parking plate must be in position and the parking bolt must be retracted.

WARNING: If it is necessary to reroute the cables remember safe operation method. 1. Check that the drive DANGER LED (D1) is illuminated. 2. Switch the power OFF from the main switch (220) 3. Wait at least 5 minutes before touching the cables. 4. Check that the drive DANGER LED (D1) is NOT illuminated. 5. If possible measure from connectors that the voltage is on safe level.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

267 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

28.2

Comment and pictures needed about the CWT overtravel dimension sticker (For on-site use, fitter records the data on the sticker for future maintenance purposes)

Commissioning

WARNING: The tests for earth continuity and insulation resistance must be performed BEFORE the power is switched on for the first time! Perform the commissioning for inspection drive and commissioning for rated speed according to the drive type: Drive type KDL16S KDM40

Instruction AM-11.65.045, Machine-room-less Elevators with KDL16S Drive, Installing, Commissioning and Safety Inspection AM-11.65.042, KDM drive system for MonoSpace® and MonoSpace® Special: installation, commissioning and safety inspection

NOTE: The remaining counterweight filler weights will be loaded to counterweight during the commissioning. Refer to relevant commissioning instruction. NOTE: For more information on the balancing load, see APPENDIX B. NOTE: Check the safety gear gap (3 mm) after commissioning. 1. 2. 3. 4.

Place all the remaining filler weights to the counterweight, split filler weights to top. We raised a safety concern during Karhu that Fit the counterweight clamps. Install the counterweight screen to final position. the lego filler weights can lift in the middle Fit the oil collectors to the guide rails. during a high speed impact and fall out of the

frame.........we are waiting on the outcome!!!

1077272.wmf

Please add another note to read as follows: 2 fixings only NOTE: finally check the of the rope Copyright ©2012adjustment KONE Corporation guards (Car & CWT) All rights reserved. Please add small pictures also.

DRAFT 268 (340)

CWT screen is 2360mm long and must be mounted at 140mm from pit to AM-01.01.250 achieve 2500mm code A) 2012-08-28 height to top (Draft of screen

KONE MonoSpace® 3.0 Installation Instruction

28.3

Final steps of commissioning

28.3.1

Balancing the empty car and counterweight

WARNING: No one is allowed to be on the car roof or in the elevator shaft.

CAUTION: Be careful while releasing the brakes. Do not let the car overspeed.

NOTE: If final car interior is added later: Add an equivalent weight in the car for balancing purposes. After the car interior has been installed, remove unnecessary weights from the car and readjust the offset and gain settings on the load weighing device.

max 3mm

1. Drive car and counterweight to the same height in the elevator shaft. 2. Open the brake. Observe the speed/direction LEDs. The car must not move. 3. Repeat the test with the car a little higher and a little lower until the empty car and counterweight are balanced. Add or remove filler weights as necessary. 4. Check that the rope tensions are equal at both rope anchorages. The rope clips must not rub each other or the ropes.

1007537-1.wmf

1076096.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

269 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

28.3.2

Adjusting slack rope switch 1. 2. 3. 4.

Check the 3 mm distance. Check the 1.5 mm distance. Adjust the switch position. Connect the cable to XLH3 on LOP-230 board in the MAP.

1 ~0 .

3

1.5

3mm

±0.5

5

2

1027503.wmf

1027496.wmf

28.4

Fine adjusting Perform the fine adjusting according to the drive type: Drive type KDL16S KDM40

Instruction AM-11.65.045, Machine-room-less Elevators with KDL16S Drive, Installing, Commissioning and Safety Inspection AM-11.65.042, KDM drive system for MonoSpace® and MonoSpace® Special: installation, commissioning and safety inspection

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

270 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29

COMMISSIONING OF THE CAR DOOR

Quality Requirements: Car doors – running smoothly with no noise – closing quietly, no slam closing – operating speed and door open dwell time according to customer requirements – closing force correctly adjusted Curtain of light (COL) – operating correctly – correctly aligned – RX unit NOT installed to slam post side on side opening doors

1077323.wmf

!!! CAUTION - issues that affect reliability !!! Incorrectly adjusted door parameters causes: – doors fail to run to optimum performance – increased probability of customer dissatisfaction – increased probability of door drive faults, break downs etc. – door closing torque too low = possibly unable to close doors – door closing torque too high = non compliance with local code requirements Incorrectly installed / adjusted COL causes: – unwanted activation failures from misaligned units – COL RX (receiver unit) installed to slam post side will cause unwanted activation from light sources on landings

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: N/A Hand tools needed: Multimeter, allen keys, Phillips screwdriver, door force gauge 5S Installation Progress Report N/A QD-181.211 QD 8 commenced

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

271 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.1

Layout of drive 10 electronic assembly

NOTE: For X1 connector, use terminal EXT GND on the door electronic assembly as the reference when measuring the control signal voltage. EXT GND terminal must be connected to the elevator control signal ground (-/24 V for TMS or EPB and so on). The internal ground of the drive 10 board is connected to protective earth.

1. Test Drive Buttons 5

2. Reference switch 3. DIP switches S1 and S2 4. Closing force rotary switch

1

5. LEDs 6. Learn button Plug description: X1 = Standard I/O

4

X3 = Transformer secundary winding S10

X4 = Motor X5 = Battery supply

6

X10 = Motor encoder X15 = Photo cell receiver (curtain of light) X16 = Photo cell transmitter (curtain of light)

5

2

3

X40 = Test drive button

X16

X15 1077697.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

272 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.2

Layout of AMD drive 2 electronic assembly

1

2 X4

X5 X40

X6

X9

3

X10

X19

X15 X16 X17 X18

X1

X2

4

P02000343.wmf

1. Test Drive Buttons 2. Encoder 3. Motor 4. Reference switch

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

273 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Plug description: X1 = Standard I/O X2 = Extended I/O X4 = Motor X5 = Battery supply X6 = Transformer secondary winding X9 = Transformer primary winding X10 = Motor encoder X15 = Photo cell 1 (curtain of light) X16 = Photo cell 2 X17 = Mechanical safety edge 1 X18 = Mechanical safety edge 2 X19 = Board line in X40 = Test drive button

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

274 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.3

Testing factory adjusted door operation

CAUTION: Door operators which are delivered directly from the factory are pre-adjusted: the learning phase is already completed and the closing force potentiometer has been adjusted.

NOTE: At power up - in normal drive, if the door is not at the reference switch (close end position) it will move at low speed until the close end position is found. After finding the reference switch (close end position) the door will move at normal speed.

Step 1 2

3

Action Note Switch on the inspection drive on the car roof. Switch on the power. Check that the doors open and close The test drive buttons operate only when when the test drive buttons are the elevator is in inspection mode (LED pressed. SD/ X1 lit). Check that the panels do not touch If necessary, the speed and closing force each other or rattle and that the car settings can be fine tuned. door operates smoothly. Switch the elevator to Normal Mode As the control panel controls the and close the landing doors. reopening, the elevator must be in the Drive the car to the landing level. Normal Mode. Check that the safety devices (open button, photocells) reopen the door.

1077701.wmf 1077700.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

275 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.4

Adjusting closing force Step 1

2

3

4

Action Open and close the door manually and check that there are no mechanical obstructions. Drive the door with the CLOSE button (or close command) to the close direction. Put a force measuring device between the closing door panels (centre opening) or between the door panel and slam post (side opening). Do not attempt to measure the force of a moving door, stop it first. Adjust the closing force if necessary using the potentiometer.

Note The test drive buttons only function when the Service Drive input (SERV. DRIVE/X1) is set.

The maximum closing force is 150 N. For centre opening door, the measuring device will show half of the actual close force. For side opening door measuring device will show the actual closing force.

CLOSE FORCE 1077706.wmf

Closing force increases when turning the close force potentiometer clockwise.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

276 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.5

LEDs, drive 10

45 +24V PC1 44 IN

X15

46 GND

Protective device LEDs Name LED illuminated if +24 V The power of the photo cell is on PC.1 IN Photo cell not interrupted

1077709.wmf

GND GND EXT 17

CLOSE

16

OPEN

10

OPEN END

30

REOP IN

31 REOP NC

X1

32

REOP NO

SD

SERV DRIVE

14

OPEN BUTT

41 PC OUT 9 CLOSE END +24V EXT

Lift interface LEDs Name CLOSE OPEN OPEN END REOPEN SERVICE DRIVE OPEN BUTTON PC OUT CLOSE END +24 V EXTERN

LED illuminated if CLOSE Command is on OPEN Command is on Door is in open end position Reopen NO (Normally Open) contact is closed = reopen request is activated Elevator Inspection drive is active Door open button is pressed Beam of photo cell is not interrupted Door is in close end position External +24 VDC available

GND GND EXT 1077708.wmf

Name POWER STATE WATCH DOG

Miscellaneous LEDs LED illuminated if Power of the board is on (24 VAC) Light: During start up and learning Flashes if a fault is detected Blinking or light: microcontroller defect

1077710.wmf

Reference switch

Doors are closed.

1078565.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

277 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.6

DIP-switches, drive 10 On

MIN

S1

SPEED

1

2

3

MAX

S1/1 S1/2 S1/3

4

ON

1 2 3 4

SP0

OFF ON OFF ON

SP1

OFF OFF ON ON

S1/4

Open force limiter in operation 24 V COL supply on

+24 V

S2 ON

1 2

S2/2

REOP OPEN BUTT.

Default settings

Speed selection, binary coded

OFL

S2/1

Off

Reopen IN “30” connected to GND EXT Open Button breaks contact to +24 V EXT

Open force limiter not in use

Off Off Off

24 V COL supply off 1 second after commands removed in close end position Reopen IN “30” potential free

Off

Open Button makes contact to GND EXT

Off

On

1077386.wmf

NOTE: When expanded I/O board is used with D10, set S1/4 on.

29.7

LEDs, drive 2

45 X15 44 46

+24V

49 X16 47 48

+24V

38

X17 G X18

39 G

PC 1 IN GND

PC 2 IN GND

Protective device LEDs Name LED illuminated if PC.1 IN Photo Cell 1 not interrupted PC.2 IN Photo Cell 2 not interrupted M.SE.1 IN Mechanical Safety Edge 1 not pressed M.SE.2 IN Mechanical Safety Edge 2 not pressed

MSE 1 IN GND MSE 2 IN GND

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

278 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

GND

17 16 10 30 31 X1 32 SD 14 41 27 GND

28 29 11 X2 9 13 40

EXT. CLOSE OPEN OPEN END REOP. IN REOP. NC REOP. NO SERV. DRIVE OPEN BUTT. PC. OUT LIMIT IN +24V EXT. EXT. SP 0 SP 1 NUD GING CLOSE END SE. OUT POS. OUT

LED LO (H23) OFF OFF ON ON

Lift interface LEDs Name CLOSE OPEN OPEN END REOPEN SERVICE DRIVE OPEN BUTTON PC OUT LIMIT IN +24V EXTERN SPEED 0 SPEED 1 NUDGING CLOSE END SE OUT POS. OUT

LED illuminated if Close Command ON Open Command ON Door is in open end position Reopen NO contact closed Elevator Service Drive is active Open Button is pressed Beams of PC1 and PC2 are not interrupted Limited open command ON External +24 VDC available Speed level 0 is selected Speed level 1 is selected Nudging command on Door is in close end position Mechanical safety edges 1 and 2 are not obstructed Door open > 800 mm

Voltage selection LEDs LED HI (H22) Line voltage selected OFF Line voltage selected = 400V range ON Line voltage selected = 230V range ON Line voltage selected = 115V range OFF Not used

Name 5 V POWER WATCH DOG STATUS 24 V POWER

Miscellaneous LEDs LED illuminated if Board powered (5 V) Blinking or light: µP-defect Light: During start up and learning Flashes if a fault is detected Power Supply for door protective devices is on

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

279 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.8

DIP-switches, drive 2 Example

Switch S1/1

S1 ON

1

PC 1

ON OFF Photo Cell 1 Photo Cell 1 enabled disabled Photo Cell 2 Photo Cell 2 enabled disabled Mechanical safety Mechanical safety edge 1 edge 1 disabled enabled Mechanical safety Mechanical safety edge 2 edge 2 disabled enabled Speed selection, binary coded, see the figure

S1/2

2

PC 2

3 4

MSE 1

5

SP 0 OFF ON OFFON

6

SP 1 OFFOFF ON ON

7

OFL

8

RAIL 1

SPEED MAX 1 2 3 4

S1/3

MIN

MSE2

P02000349.wmf

S1/4 S1/5 S1/6 S1/7

Open force limitation active Drive attached to railing 1 (ADV railing)

S1/8

Example S2 ON

1

REOP

2

OPEN BUTT.

Switch S2/1 S2/2

ON Reopen IN “30” connected to GND Open Button brake contact to +24V

No open force limitation Drive attached to railing 2 CAUTION: Do not use this for railing 1. The railing and belt can be damaged.

OFF Reopen IN “30” potential free Open Button makes contact to GND

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

280 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

29.9

Commissioning of curtain of light Step 1

Action 2D curtain of light: Check that the red LED in the receiver at about 1700 mm height is lit when the beams are obstructed. 3D curtain of light: Check that the red LED at about 1900 mm height in receiver is lit when the beams are obstructed or when the 3D sensor (in either receiver or transmitter edge) is detecting an obstruction. The red LED in transmitter will only be on when the 3D sensors of the transmitter edge are detecting an obstruction.

29.9.1

Note 2D/3D curtain of light: It is also possible to measure the signal line change from GND to 24V if any obstruction is detected. On the heavy duty operator beam obstruction is indicated by a green LED on the PC1 input (number 44).

Fault finding If LEDs are OFF, but doors do not close Step 1 2

3

Action Check cables and supply. Check that the signal output is not disconnected from the door operator or maintenance access panel. Check that the door operator or maintenance access is responding the signals by connecting the signal input to GND. The doors should close.

Note

If the doors do not close the problem lies within the control system.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

281 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

If LED in receiver is ON but doors do not close Step 1 2 3 4

Action Note Check that the 24 V supply is present on the transmitter unit. Check that the curtain beams are not obstructed. Check that the filters are not dirty. Check that the distance between the units is not greater than the maximum specified.

If doors attempt to close and then re-open (3D curtain of light) Step 1

2

Action Note Check that the 3D sensors are not detecting any obstruction caused by: – landing doors during door closure – opposing slam or landing entrance – the installation bracket Observe the LEDs in transmitter and Both LEDs lit: problem in transmitter. receiver units during door closure to Receiver LED lit: problem in receiver. find out which side is causing problem. Transmitter problem: Turn switch 2 in the transmitter unit dip switch to OFF position to disable the 3D function. If the doors now close correctly, turn switch 2 to ON position and turn switch 1 to OFF position to reduce its 3D. Receiver problem: Turn switch 2 in the receiver unit dip switch to OFF position to disable the 3D function. If the doors now close correctly, turn switch 2 to ON position and turn switch 1 to OFF position to reduce its 3D.

If none of the previous possibilities resolves the problem, substitution of both units is necessary.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

282 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

30

FINAL STEPS AND ELEVATOR SHAFT CLEANING

Quality Requirements:

Final steps and elevator shaft cleaning – levelling accuracy checked – emergency battery drive function checked – complete installation cleaned and waste removed Guide rail lubrication – oil lubricators must be filled with the correct oil (supplied) – oil lubricators must be adjusted to ensure • correct contact with guide rail surfaces • correct oil flow distribution

!!! CAUTION - issues that affect reliability !!! Failure to perform shaft cleaning causes: – poor ride comfort as dirt contaminates the guide rail oil – smooth operation of doors is affected by dirt collecting on / in the sills / railings – possible slip and trip hazards Failure to lubricate the guide rails causes: – ride comfort issues (noise / vibration) – drive faults / failures – premature shoe liner wear

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Safety barrier Hand tools needed: Tape measure, Phillips screwdriver, 2 x spanner (19 mm), brush, vacuum cleaner 5S Installation Progress Report Commissioning + testing completed QD-181.211 QD 7.1 and 8 completed

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

283 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

30.1

Correction of parameter settings

Before driving on the car roof, change the parameter 1_71.

Step 1

30.2

Action Check the setting of the parameter 1_71. The setting of parameter 1_71 MUST BE 0. Otherwise the car drives too high on inspection drive. Inspection drive stops latest at the terminal floor level.

Note If the value of parameter 1_71 is something else than 0, change it to 0.

Checking the levelling accuracy Step 1 2

Action Drive in the car to each floor from both directions. Measure the difference between the car and landing sill levels at each landing.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

284 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

30.2.1

Adjustment of the levelling if necessary Step 1 2

3 4 5 6

30.3

Volume adjustment (audible feedback) Step 1 2

3

4 5

30.4

Action If levelling needs adjustment, drive to the topmost floor and go to the car roof. Check that the distance between the If this distance is correct, but the elevator 61:U and 61:N switches is 130 mm. is relevelling, adjust this distance to This setting defines the normal 125 mm and repeat the setup. stopping point. Drive on the car roof and correct the magnet positions. Leave the car roof and repeat setup if any adjustment was made. Re check the levelling accuracy by driving to each floor on normal drive. Repeat checking, if needed.

Action Note Select the main menu "7" at the User-Interface. Select the submenu for the volume 7_80 Button Buzzer Volume adjustment. 7_81 Button Buzzer Volume, Main Floor 7_82 Gong Volume 7_83 Gong Volume, Main Floor Adjust the parameter value of the The value range is from 0 (OFF) to 10 submenu with up and down keys of the (MAX). user interface. Press ACCEPT. Stores the new values. Switch the power off and on. This action transfer the new values to the signalisation devices.

Group locking function LMC function (Locking of Multiple Car calls) allows the locking of multiple car calls using the key switch(es) on the KSS car operating panel. The locking groups are configured using the car operating panel and User Interface. For more information refer to 812232.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

285 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

30.4.1

LMC configuration Step 1 2 3 4

5

6 7 8 9 30.4.2

Resetting the LMC configuration Step 1 2

3

30.5

Action Note Drive the car to the floor where the maintenance access panel is located. Turn the elevator to RDF. Set the LMC setup mode parameter Value 1: setting the locking group 1 (1_5) to 1 (or 2). Value 2: setting the locking group 2 Configure the locking group by pushing To remove the locked call from the the car call buttons. The collars of the locking group push the button again. The buttons light up. collar lights down. Store the locking group configuration by The value of the LMC setup mode pushing one of the door open buttons parameter (1_5) changes back to 0 on the car operating panel. automatically. Set the locking type parameter (1_45) to 1 or 3 to enable car calls locking. Switch the power OFF. Turn the RDF OFF. Switch the power ON and verify the locking operation.

Action Turn the elevator to RDF. Set the LMC setup mode parameter (1_5) to 100, 101 or 102 to reset the locking groups. Turn the RDF OFF.

Note Value 100: reset all the groups Value 101: reset only the first group Value 102: reset only the second group

Emergency lighting battery and KONE remote monitoring Step 1

2

Action Connect the emergency lighting battery plug “227 Battery” in the car roof electrification unit.

Note If the elevator main switch is switched off disconnect the emergency lighting battery temporarily to prevent unnecessary discharging. Note that landing calls do not operate when the battery is disconnected. Make settings for KONE remote monitoring (KRM) according to section APPENDIX C. on page 307.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

286 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

30.6

Emergency battery drive (EBD-A) test Step 1

2 3 4

Action Note Enable EBD-A mode in maintenance access panel. Action Display Push MENU button until number 1 1 __ __ shows on the MENU display. Push ACCEPT button. Number 1 1 _1 __ shows on the SUBMENU display. Push ^ - button until number 87 shows 1 87 __ on the SUBMENU display. Push ACCEPT button once. A blinking 1 87 _0, where 0 is blinking number 0 shows on the VALUE display. Push ^ - button until number 1 shows 1 87 _1, where 1 is blinking on the VALUE display instead of 0. Push ACCEPT button to confirm the 1 87 _1, where all the numbers are selection, all the numbers are steady. steady Switch the power OFF. This action restores the setting. Switch the power ON. Run the elevator in normal mode. When the elevator is between floors, Do not switch OFF 220. switch OFF the main supply to the riser. After 10 seconds EBD-A should start to supply power to the control panel, the car should drive to the nearest floor level CAUTION: After the EBD-A has and the doors open. operated wait 20 minutes before After 4 seconds doors should be running the elevator. completely open and EBD-A switched This is to ensure a proper cooling of OFF. the internal components and to prevent possible failures.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

287 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

30.7

Testing the compensation chain Step 1

Action Test drive the elevator rapidly up and down. If the compensation chain hits the wall of the car or swings strongly during the drive. Reduce the dimension L slightly.

Note

1033259.wmf

30.8

Elevator shaft cleaning Step 1 2 3 4 5 6 7

Action Clean the headroom. Clean the brackets and guide rails. Clean the doors and landings. Clean the car roof. Clean the car interior. Clean the pit. Handle the waste (according to regulations.)

Note

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

288 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

31

SAFETY INSPECTION

Quality Requirements: Safety inspection – all safety systems checked – relevant documentation compiled and stored in the Site Project binder, copies sent to local KONE branch office • Safety inspection • Test Sheets • QD-181.211

!!! CAUTION - issues that affect reliability !!!

5S

SORT STABILIZE SHINE STANDARDIZE SUSTAIN

Method tools needed: Safety barrier Hand tools needed: Multimeter, insulation resistance meter, handheld tachometer, allen keys, Phillips screwdriver, tape measure, testweights,2 x spanner (19 mm), pencil 5S Installation Progress Report Commissioning + testing completed QD-181.211 QD 7.1 and 8 completed

31.1

Safety inspection Perform the safety inspection according to the drive type: Drive type KDL16S KDM40

Instruction AM-11.65.045, Machine-room-less Elevators with KDL16S Drive, Installing, Commissioning and Safety Inspection AM-11.65.042, KDM drive system for MonoSpace® and MonoSpace® Special: installation, commissioning and safety inspection

NOTE: Check that all safety gear marks are removed from the guide rails after safety inspection.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

289 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

32

HANDOVER

32.1

Prerequisites Before the handover procedure can take place, the safety inspection must have been completed and passed. The safety inspection also covers issues described in EN81 Annex D, which gives mandatory actions from a code point of view, where EN regulations apply. It is also important to verify that some of the issues in the handover form have already been checked during the safety inspection.

32.2

Handover form In the handover form there is a list of items that are assessed during the handover procedure. Local practices determine whether it is necessary to specifically examine all the different points on the list. However, both the installation and maintenance representatives must be positive that the items listed are in an acceptable condition. The purpose of the form is that its subscribers know that the installation meets KONE quality standards.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

290 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

E-line MonoSpace™ Installation/Service Handover General data Elevator Number

Date

Elevator Address

Installation Representative

Maintenance Representative

Handover Checks Accepted Yes

No

Why not?

Ride Quality Levelling Car & Signalization Control panel Brake Machine Traction sheave and ropes Guide rails Shaft Doors Landing door mechanical Landing door locks and contacts Car door mechanical Car door electrical

O.S.G. and Safety gear Pit

Installation accepted to maintenance Yes

No

If rejected, person responsible for corrective actions Agreed deadline for completion of the work

Installation Representative

Maintenance Representative

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

291 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

32.3

Installation quality checks The following pages of this document contain a list which describes the required condition of the installation in detail. Refer to it whenever you are unsure whether a component is in an acceptable condition or not. Ride quality – There should be no vibration during the acceleration or deceleration. – There should be no sudden movements or unexpected noises during the drive. Levelling – Maximum levelling deviation in either direction is ± 5 mm. Car and signalization – – – – –

Push buttons and signalization should work as expected in the car and on the landings. Car lighting should operate correctly. Car emergency light should operate correctly. Decoration should be clean and free from scratches and dents. There must not be any unnecessary installation time protections, such as plastic coatings left. – Remote monitoring and alarm buttons (3 pcs) must function correctly. – Car labels must be in place. – Car fans should operate correctly. SEP panels and MAP panel – – – – – – – – – – – –

All covers and protections must be correctly positioned. All unusual registered faults should be solved and unit reset. MAP door must be locked and closed properly. There should be no abnormal noises coming from the contactors, etc. Overspeed governor remote test should work. Safety gear must stop and hold the car when overspeed governor remote test is operated while car is moving down. Elevator shaft emergency light and alarm bell must work when power is off. Rescue drive should work in both directions. Brake must engage fully when handle is released. There must be no kinks or other deformations in the brake release cable. The brake must stop the car in an up direction emergency stop. There must be no excessive slide. All earth wires on the whole installation must be correctly connected to the earth terminal. ANY ELECTRICAL OVER CONNECTIONS MUST BE REMOVED

Machine – All internal and external fastenings should be tight and locating pins in place. – The braking surface on the machine should be clean and free from rust and other contaminants. – There must be no mechanical contact with machine body and fixings.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

292 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Ropes – Ropes must be free from rust. – Should not be dry or dirty, and there should be no broken strands, kinks or twists. If ropes are dry, arrange relubrication of ropes according to AM-09.01.006. – Rope labels must be attached to the rope suspensions. Traction sheave, rope terminations and springs – – – – –

Maximum deviation in spring length must be 3 mm. Rope anchorages must be correctly secured with two nuts and a split pin. Ropes should be secured with rope grips. There should be no evidence of twisting of rope termination. There should not be any mechanical contact between rope grips.

Guide rails – – – –

Should have a light film of oil over the full length of the blade faces. Should be smooth and free from safety gear marks. All fixings must be tight. Maximum permissible DBG deviation is -0 mm, +1 mm.

Elevator shaft – Pulleys should rotate silently. – All elevator shaft lighting should work. – Final limit switches must operate, the roller must rotate and the switch must meet the ramp both top and bottom. Ramps must be correctly vertically aligned. – Top and bottom safety spaces must be according to the layout drawing. – The travelling cable loop should be a minimum of 150 mm from the pit bottom when the car is on the bottom floor. The loop inner diameter should be a minimum of 400 mm. – Car insulation should be in place. Guide shoes – Guide shoes should be correctly adjusted with a total gap in distance between the guide rails of max. 2 mm. – Oil cups should be full. Travelling cable – Should hang correctly. – Should be in good condition with no cracks, marks etc. on external insulation. – The text side should be outside the loop. Car roof – Should be clean, tidy and free from oil or grease. Car top connection box – All electrical devices and switches must work correctly.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

293 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Safety devices – Blocking pin must easily enter the slots in guide rail plate without excessive force. – Blocking pin plate must be positioned at the guide rail joint plate. – All safety switches must operate correctly. Counterweight – – – –

Free movement of shoes between rails should be between 2 and 3 mm. Oil cups must be full. Rope guards must be in place. Filler blocks must be in place and securely fixed down.

Landing door mechanical – If no longer required, surface protections should be removed. – Must be adjusted so that panels do not touch each other. Maximum gap between frame, sill or another panel is max. 6 mm (nom. 5 mm). For glass panels maximum gap between frame and panel is 3 mm. – Max. door gap in closed position, with 15 kg hand force is 30 mm (measured at the bottom of the panels). – Synchronization rope should touch the steel back plate when pressing it with thumb at distance of 10 cm from the synchronisation roller. – Rollers should run smooth, aligned with the guide rail. – Anti-tip rollers must slightly touch the rail. – Closing weight wire guard on diverting pulley should be in horizontal position, not touching the wire. – Sills should be clean and securely fixed – Distance between car sill and landing sill should be 30 ± 1 mm. Landing door locks and contacts – – – – – – – – – – –

Contacts should be clean. Lock hook and beak overlap when contact operates must be min. 7 mm. Contact bridge should push the contact surface down min. 3 mm. Contact bridge should be aligned to the middle of contactor holes, not touching the hole edges. Electrical terminations should be tight and secured. Must move freely and close by itself. Must be securely fixed. If the door opens, safety circuit must be interrupted. Lock buffers should be in place. Landing lock rollers should rotate. Emergency opening device must operate and the lock must return automatically to locked position.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

294 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Car door mechanical – – – – – – – – – – – – – – – – –

Door shoes must be securely fastened. Shoes should not allow the door to rattle on normal operation. Distance between door bottom and sill should be max. 6 mm (nominal 5 mm). Synchronization rope should touch the steel back plate when pressing it with thumb at distance of 10 cm from the synchronisation roller. The drive belt sides should touch each other when pressed with thumb in the centre of the belt. Coupler rollers should be in the middle of operator vanes, running clearance min. 5 mm, nom. 10 mm. Couplers should engage properly, engagement with rollers 10 mm ± 1 mm. If the door is opened, safety circuit must be interrupted. Must be adjusted so that panels do not touch each other and any gap between frame, sill or another panel is max. 6 mm, nom. 5 mm. Should not rattle during drive. Should operate smoothly, also when looking from the landing side. Should be correctly aligned with the slam post. Door operates correctly (check by operating manually from car roof). All rollers should run smoothly and be aligned with the guide rail. Panels should run smoothly and be aligned with the guide rail. Rollers and diverters should be firmly fixed, not causing noise. Anti-tip rollers must prevent the door from leaving the track.

Car door electrical – – – –

Should be free from dust Contact bridge should push the contact surface down min. 3 mm. Door operator buttons must operate correctly. Door protective devices must reopen the door action when operated.

Overspeed governor and rope – – – – –

Should run quietly. Must operate freely when tested by hand. Electrical contact must work. Seal should be intact. Rope should not be dirty and there should be no broken strands, kinks or twists.

Safety gear – – – – –

Must be correctly aligned, the rollers must meet both guide rails evenly. All bolts and nuts must be in place and properly fixed. Both sides must operate synchronously, gripping at the same time. Must be fully disengaged during normal operation. Must move freely and engage fully, when operated by pulling the overspeed governor rope.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

295 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Pit – There should be no oil, rubbish or water in the pit. – Oil collectors should be in place. – Buffers must be securely fixed. Overspeed governor tension weight – Must fully tension the governor rope. – Safety switch trigger should be in the middle of the opening and must operate before the weight touches the floor. – Should move easily.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

296 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

33

FAULT FINDING Refer to APPENDIX for LCE fault codes and for drive fault codes.

33.1

Fault finding procedure If the elevator does not run correctly follow this procedure. Step 1 2 3 4

33.1.1

Action Note Check the normal run. Investigate the LEDs in the user Refer to the table on page 323. interface. Check the fault in drive system. Perform the setup drive. (Set the elevator to setup mode, refer to page 305.) Check the load weighing set up and balancing.

Operation of the elevator during the setup drive Step Action / Function 1 Start the setup drive. 2 Elevator starts to move upwards.

33.2

3

Elevator makes a setup drive.

4

Setup is ready if the floor counting is correct.

Note If elevator does not start to move upwards check the position of the car and status of magnetic switches. If elevator does not make the setup drive check the polarity of encoder and motor. Check the motor parameters. If the floor counting is not correct, magnetic stripes are in the wrong position or too close to the switches.

Normal run The following table shows the LED sequence when the elevator is working properly. LEDs 9 SPEED> 0.1 m/s

Explanation Speed of the elevator is more than 0.1 m/s.

Note

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

297 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

LEDs 8 START PERMIT

7 MAIN CONTACTOR

Explanation Indicates that both main contactors (pos. 201:1 and 201:2) and both auxiliary main contactors (pos. 201:3 and 201:4) have released after previous drive. If the LED stays active after drive, either of the contactors is stuck open and further drives are not possible. Indicates that both drive and LCECPU control have given main contactor activation command.

6 SHAFT DOOR CONTACT

Indicates that all landing doors are closed.

5 CAR DOOR CONTACT

Indicates that car doors are closed.

4 CLOSE DOOR COMMAND

Indicates that LCE gives Close Door command.

3 DRIVE NEED

Indicates that the controller has recognised a need for drive. This can be a given call or specially given command for parking drive, fireman’s operation etc.

2 V3F OK

Communication between the drive unit and CPU is OK.

1 SAFETY INPUT

Indicates that safety circuit is OK.

Note LED is off when both main contactors and both auxiliary main contactors are released and start permit input on XD1/3 connector (LCEADO pos. 379) is 0 V. Main relay triac on LCEADO (pos. 379) should open and both main contactors should energise. Input XH2/3 SHAFT DOOR CONTACT (pos. 379 LCEADO) has voltage. Input X1/7 CAR DOOR CONTACT (pos. 379 LCEADO). Command is active during the drive, and it disappears after the doors are closed and the elevator is not active, i.e. there are no active calls. If the LED does not light when a call from car operating panel or landing button is given, either the button is faulty, the connection between button and controller is faulty or controller is faulty. Switch the power OFF for 10 seconds and try again. Check the parameter 1_95. Input X1/5 ‘STOP CONTACT’ (pos. 379 LCEADO) has voltage.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

298 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

33.3

Faults in drive system

33.3.1

Checks Make the following checks before the drive can be operated. Step Action 1 Check the motor parameters.

Note The motor parameters should be according to the motor type. Check that motor, brake, encoder, resolver and thermistors are connected. Check the connections to the main circuit board. Check the travelling cable connections.

2 3 4 33.3.2

Adjusting magnetizing current ratio and acceleration factor Needed when elevator does not run with half load. Step 1 2 3

33.3.3

Action Adjust magnetizing current ratio and acceleration factor. Save parameters to permanent memory. Switch the power OFF and ON.

Note 6_52, max. value 0.80 6_57, max. value 1.30 6_99, value 1

Drive control After the MODE command is given, drive performs the following supervisions: 1. 2. 3. 4. 5.

33.3.4

DC Link voltage must be over 400 VDC. The braking resistor must be connected. The thermistor must be connected. The resistance of the NTC sensor must be >1500 ohm. Current sensor must not give overcurrent information.

Start, up or down If the supervisions are OK, the MAIN CONTACTOR ENABLE signal is sent to LCE: 1. MBE signal. IGBT will be activated. 2. Brake command. Brake opens. 3. Speed signal. Speed is dependant on type of MODE command.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

299 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

33.3.5

Crash stopping of the drive Faults for crash stopping of the drive may be the following: 1. 2. 3. 4.

Missing or incorrect encoder signal. Check from the LCE. Wrong polarities of motor or encoder. LED should be lit in down direction. Wrong parameters. Set the default parameter values. Supervisions, as described before.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

300 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

34

APPROVALS AND VERSION HISTORY Compiled by:

Information Product Author / Ville Malmiala

Checked by:

Global Installation Support / Richard Baker

Approved by:

Global Installation Support / Hakan Barneman

Issue Date Description of Change 2012-05-28 First issue. Draft 2012-08-28 Counterweight with safety gear added. A Other changes, see change bars.

Ref CR

Approved by Hakan Barneman

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

301 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

35

FEEDBACK Click one of the star buttons in the PDF version to rate the document and report errors or suggest improvements. This opens your default e-mail client. Users of printed documents can send feedback directly to [email protected]. Excellent

Good

Average

Acceptable

Insufficient

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

302 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

APPENDIX A. KDL DRIVE RELATED ISSUES A.1

Returning the initial settings, KDL16S This is recommended when you do not know the status of the settings of the DCBL board. Step 1 2 3

A.2

Action Set Parameter lock (6_95) parameter to 0. Set Default parameters (6_98) parameter to 1. Wait at least 15 seconds.

Note

Value changes automatically back to 0.

How to use Real time display function This chapter is a general instruction describing how to activate and use Real time display function. The Real time display function is a build in feature which measures / shows the different drive module signals on the LCE user interface. The RealTimeDisplay monitor selection (6_75) parameter activates a function that enables for example: observing of the elevator speed, direction of the car movement, position of the car and motor current in real time. For more details see drive parameter list 972483D01. Step 1 2 3 4

5

Action Note Select RealTimeDisplay monitor selection (6_75). Select any of the elevator functions that See parameter list. you want to see (1...209). Return to floor display by pressing the Menu-button. Activate the Real time display by pressing Select/Accept-button. You can now use Select/Accept-button to change display to show floor, real time or speed display. De-activate the Real time display by Press Menu-button. returning to floor display.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

303 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

A.3

Reading detailed fault codes The sub fault codes of the drive are describing the faults in detail. The numbering of the sub fault codes is divided to the following categories: – – – –

1000-series, the elevator is locked (driving is prevented). 2000-series, driving of the elevator is stopped by a machine brake. 3000-series, warnings indicated in advance (before a device or equipment break down). 6000-series, diagnostic information. All sub codes in this category DO NOT indicate a fault. They are for getting additional information.

How to read the sub fault codes

This example describes how to read sub codes 118_6010 and 118_6011. 1. Enter error log. 1.

SELECT 2. ACCEPT

2. Push ACCEPT (a row of figures starts to scroll).

118 Shaft Setup 118

2021

Setup started at wrong position

2023

Setup stopped because 77:U/N active at same time

6010

Reports minimum 61:U/N overlap

floor

overlap mm

1021405

f

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

304 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

APPENDIX B. BALANCING FACTORS AND LOADS Some elevators use adaptive balancing where the balancing load is less than the traditional 50% of rated load. The balancing load varies depending on speed, rated load and travel. The weight difference must be compensated with the balancing (6_10) parameter of the drive, load weighing device GAIN value and using a matching balancing test load during commissioning. To determine whether an elevator uses adaptive balancing, see the layout drawings (car balancing factor %). If an elevator with adaptive balancing is already in operation, the MAP has a sticker that states the car balancing factor. For more information on the car balancing factors and loads used with adaptive balancing, see the layout drawings and commissioning instruction (AM-11.65.042 or AM-11.65.045).

xx%

49%

40 41 42

D400

43 44 45 MENU

xx%

SELECT

46 47

ACCEPT

48

D330

6_10=xx CAR

49 50

NOTE:

D330

CWT

1073186.wmf

Figure B1.

Adaptive balancing in layout drawings (left) and sticker in MAP (right)

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

305 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

APPENDIX C. KONE remote monitoring (KRM)

C.1

Installation on car roof Step Action 1 Remove the overconnection plug from the connector XC9C on the KNXRIF board (inside the car top connection box). 2 Connect the alarm button cable to connector XC9C. 3 Check that the alarm button of the inspection drive unit is connected to connector XC9B on the KNXRIF board. 4 Route and connect the cable between the F2KMUL board (J2) inside the COP and KNXRIF board (X12) inside the car top connection box. Usually the cable is pre-fitted to the F2KMUL board.

Note

XC9B XC9C X12 KRMRIF

F2KMUL

1010660.wmf

C.2

Normal phone line connection Step Action 1 Connect the telephone line cable between the travelling cable plug (XC20) and the socket on the shaft wall.

Note

1010661.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

306 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

C.3

GSM terminal Step 1 2 3 4 5

Action Note Insert the SIM card to the GSM terminal. Connect the flat cable to the GSM terminal. Remove the knock out of the car top connection box for the flat cable. Fix the GSM terminal to the car top connection box with screws. Connect the GSM terminal cable to the KNXRIF board (X20).

3

1. SIM card 2. Flat cable position 3. Knock out

1

2 1010662.wmf

C.4

Setting of the rotary switch Step Action 1 Check the jumper JP1 position on the KNXRIF board.

Note

Correct jumper position: – over the two left hand pins, KNXRIF board microphone in use. 2

Check that the setting of the rotary switch on the KNXRIF board is correct.

Refer to the following table.

SYSTEM

ROTARY SWITCH POSITION

GSM terminal. Normal telephone line, one elevator. Normal telephone line, more than one elevator connected to the same telephone line.

1 1 Each elevator has its own individual number and rotary switch position.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

307 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

C.5

Start the configuration

NOTE: Configuration must be done after commissioning for normal speed.

Step Action 1 Switch elevator’s main power and car light supply ON. 2 Check the LEDs on the KNXRIF board. See section C.7 on page 311.

Note

1

OFF

ON

LD2 LD1

LD6 1. Blinking 3

Check the GSM LEDs (if available). See section C.8 on page 313.

4 5

Contact the local KONE Service Centre. Give the following information of the KRM installation to the KONE Service Centre. – Equipment number – Telephone number – Rotary switch position on the KNXRIF board (RIF ID) – Prefix, if the telephone is installed via PBX (switch board) – Local ID (LID), always 1 GSM terminal, in addition to previous information: – Telephone number for data – Modem type Wait until the configuration is made by A blinking LED (alarm registered, yellow) the KONE Service Centre. on the KNXRIF board and alarm Normally it takes a few minutes. registered indication on COP indicate an ongoing configuration download. When the blinking stops the download and configuration are complete. Check that the LED1 on the KNXRIF board is ON and other LEDs are OFF.

6

7

OFF

OFF

ON

1

2

3

P12000044.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

308 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

C.6

Verify Emergency Alarm Button operation Step Action Note 1 Drive the car to the lowest floor. 2 Press the alarm button of the car operating panel. The KONE Service Centre answers and the voice connection is activated. 3 Check from the responding operator that the building address information and elevator number are correct. 4 Ensure that the voice level and quality are acceptable. 5 Adjust the voice level if necessary. The voice level must be adjusted during the call to the Service Centre. Place a small magnet on the reed relay. After pressing a few times a beep sound Press the alarm button as many times indicates that you have reached the as necessary (the voice level highest possible voice level. increases). If you continue pressing, the voice level will drop down to the lowest level.

Out of service Fireman’s service Overload Priority call Call locked Attendant service Hospital service Call in progress Speak now

F2KMUL

1010806.wmf

6

7

Press the alarm button on the car roof and under the car. Ensure that the voice connection and alarm are activated correctly. Check that the system has been reset Check that the LED1 on the KNXRIF by the Service Centre. board is lit and other LEDs are OFF.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

309 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

C.7

LEDs and switches on KNXRIF board KRMRIF board locates in the car connection box on the car roof.

JP1 JP1

1009480.wmf

Indicator LED Mains

Colour Green

LED Batt

Red

LED Alarm

Yellow

LED Call

Yellow

LED PSTN fail

Red

Status On Blinks 1 Hz Off On

Off 0.5 s. ON, 0.5 s OFF On 2 s. ON, 1 s. OFF 0.3 s. on, 0.3 s. off, 0.3 s. on, 2 s. off OFF On Off On

Off

Indication meaning Mains power on. Mains not connected (battery used). No power at KRMRIF (unit not in use). Battery failure (below 10.5 VDC). - battery voltage low due mains power failure - battery dead, needed to be replaced - battery fuse operated Battery is OK. Alarm registered but not served Alarm active but served Configuration download ongoing. No configuration, wrong configuration

No alarms activated. Telephone call in progress. No calls. Line is missing, line voltage less than 33 VDC or no dialling tone and the possibility of a black listed KSC number. Telephone line status is normal.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

310 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Indicator LED LON fail

Colour Red

Status On

Indication meaning LON communications link fail. One or more analyzers do not communicate Lon cable break Analyzer power failure No connection to LON -chip Network configuration error Escalator serial communication failure with escalator communicator. Non configured analyzer is connected to RIF.

Blinks 1 Hz

LED ICT

0.3 s. on, 0.3 s. off, 0.3 s. on, 2 s. off Off On

Red

Communication works correctly In circuit test has detected a fault on the KRMRIF board. If the LED is continuously ON or blinks replace the KRMRIF board. KRMRIF is working correctly.

Off Setting JP1

JP1 1 1 1009482.wmf

Voice link uses microphone on the KRMRIF board. (Car roof alarm button in inspection drive unit) Voice link uses microphone on the separate ALBU unit on the car roof.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

311 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

C.8

Indicator LEDs of the GSM terminal The functionality of the three light indicators in start-up, normal and special situations is described in the following tables respectively.

1 2 3

1. LED 1 2. LED 2 3. LED 3

1006322.wmf

LED 1 OFF Green scan 500 ms on OFF OFF Red or Green blink

LED 1 OFF OFF

LED 1 Green/Red blink Red blink Yellow

Nokia 30 light indicator states during start-up (10 seconds) LED 2 LED 3 Description OFF OFF Power OFF Green scan Green scan Power on, connecting to network Red blink Red blink OFF

OFF Red blink OFF

PIN query PUK query Field intensity poor

Nokia 30 light indicator states during normal operation LED 2 LED 3 Description OFF Green In service OFF Green blink Call on Nokia 30 light indicator states in special situations LED 2 LED 3 Description Green/Red Green/Red Insert SIM card or replace blink blink Red blink Red blink Failure, replace GSM terminal Yellow Yellow Initializing (short yellow blink), if stays yellow then replace the terminal.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

312 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

APPENDIX D. ELECTRIFICATION PANELS, INTRODUCTION D.1

KDL16S drive module (KM51004000V001, V002)

3

4

1

5

D1 2

1076282.wmf

Pos 1 2 3 4 5

Name

Number

Slide deck Bottom cover plate Braking resistor assembly Module fan, 2 pcs Contactor board (CO16)

LED DANGER (D1)

Colour Red

Status ON

KM50014767 KM964619G24 Indication meaning DC-link is charged.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

313 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.2

KDM drive module KR6 / KR7

1

2 3 4 5 1066396.wmf

1 2 3 4 5

Fan I/O board Power supply cable connecting points Earthing clamps PE grounding terminals

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

314 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Safe de-energizing method

– Check that the yellow DANGER led is lit. – Disconnect and prevent reconnection of the possible emergency power supplies. – Switch OFF the main switch (220). Lock and tag. – Wait for 5 minutes. – Check that the yellow DANGER led is NOT lit. – Open the cover. Check that there is no voltage (AC) in power supply terminals L1-L2, L1-L3, L2-L3, L1-ground, L2-ground, L3-ground. – Check that there is no voltage (DC) in the intermediate circuit between terminals DC+ and DC-.

L1

L2

L3

U

V

W

DC+

> 50 VDC

1067199.wmf

L1

DC-

1067127.wmf

L2

L3

U

V

W

DC+

DC-

1067126.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

315 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.3

KDA module

1

2 5

3

6 4 7

1066394.wmf

1 2 3 4 5 6 7

DCBG board Circuit breaker (298) Terminal blocks (PE) Contactor (201:1) Motor fan control MCCB2 board BCB25 board

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

316 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.4

Panels in the elevator shaft (KDM)

1

7

8

1 7 8

KR6/KR7 drive module KDA module (slim) SEP

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

317 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.5

Shaft electrification panel (SEP) 1. Transformer module 2. LCEREC board 3. LCECPU board 4. LCECAN board 5. LCEKNX or LCEVOI board 6. LCEADO board 7. LCEOPT board 8. LCERAL board 9. LCEGTW board 10. LCEDOMCS board 11. Cover 12. Contactor module

1

2 3, 4, 5

12

6 7 8 9 10 7

11

1075340.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

318 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.6

Maintenance access panel (MAP) 1. Light 2. Maintenance intercom / firemen’s drive (option) 3. Brake release lever 4. LOPCB board 5. Socket (274) 6. Run button (270:RB) 7. RDF switch (270) 8. Car light fuse (290:1) 9. Residual current circuit breaker (236) 10. Shaft light fuse (290:2) 11. Impulse relay (268) 12. Main switch (220:2) 13. Lighting switch (262) 14. LOP230 board

5 6 7 8 9 1

10 11

2 12 13

3 14

4

1078973.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

319 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.7

User interface The buttons and display in the user interface

XL8

XL1

1

OSG TEST

2 3 4 5 6

XL9

S14

LOP-CB 763603H01

1. User interface 2. Overspeed governor test button 3. Menu display 4. Sub menu display 5. Value display 6. Value setting button 7. Menu button 8. Select/Accept button 9. Up call button 10. Down call button 11. Car call button 12. Inhibit door opening switch 13. Inhibit landing calls switch 14. RS232 mode, always keep the switch in left position 15. RDF up button 16. RDF down button 17. OFFSET 18. GAIN

D22

D26

D25

D24

D23

UP CALL S8

MENU

7 8

S6

SELECT

S10

CAR CALL S4

S7 S5

ACCEPT

S9

DOWN CALL

9 10 11 12 13 14 15

S13 S12 RS232 MODE

SPEED

RDF UP

S11 LOPCB TEST

>0.6 m/s S2 -0 m/s

RDF DW

16

S1 OFFSET R127

>0.6 m/s

TP4 TP3

LWD TP6

SPEED MEASUREMENTS GAIN R146

TP5

MOTOR CURRENT

17

TP2

TP1

18 XL2

XL3

XL4

XL5

XL6 1007529.wmf

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

320 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

Use of the buttons in the user interface

Pos. 7

Button MENU

8

SELECT / ACCEPT

6 11

Arrow buttons CAR CALL

9 10 15 16

UP CALL DOWN CALL RDF UP RDF DW Pos.

Action Push MENU button to select the menu. Refer to the LCE parameter table. Push SELECT / ACCEPT button to select the sub menu. Refer to the LCE parameter table. When MENU display is blank, you can choose the required floor number using arrow buttons and push CAR CALL. You can give landing calls up and down by pushing UP CALL or DOWN CALL. Recall drive up. Recall drive down.

2

Switch INHIBIT DOOR OPENING INHIBIT LANDING CALL OSG TEST

14

RS232

Use this switch to make the overspeed governor test and to release the overspeed governor after testing. Keep this switch always in the left position.

Potentiometers GAIN OFFSET

Description These potentiometers are used to set the load weighing device.

12 13

Pos. 18 17

Measuring point LWD TP5 TP6 Speed TP3 + measurements TP4 Motor current TP1 + TP2 -

Action Use these switches to inhibit door opening and landing calls during test drives to avoid interruption of the test or trapping of passengers.

Polarity Gain Offset Tachometer voltage Motor current

Description Not used. Use these measuring points for speed measurements. Use these measuring points for measuring the motor current.

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

321 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

LEDs in the user interface board

LED +24V +5V +12V -12V LCECPUnc RUNNING LIFT IN FAULT EMERGENCY ALARM INSPECTION

Function when LED is ON + 24 V DC control voltage is OK. + 5 V DC control voltage is OK. + 12 V DC control voltage is OK. - 12 V DC control voltage is OK. Indicates that CPU and SW are working. Fault prevents the car driving. Emergency alarm push button pushed in car. Inspection drive from car roof is ON (42:DS).

Normal status ON ON ON ON Blinking

Colour GREEN GREEN GREEN GREEN YELLOW

OFF OFF

RED RED

OFF

YELLOW

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

322 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

LED RESCUE DRIVE CAR COMM OK HOISTWAY COMM. OK +24V CAR&SHAFT OK SPEED > 0.1m/s

START PERMIT

MAIN CONTACTOR SHAFT DOOR CONTACT CAR DOOR CONTACT CLOSE DOOR COMMAND DRIVE NEED V3F OK SAFETY INPUT DRIVE UP 77:U 61:U 30 B30 61:N 77:N 77:S DRIVE DOWN OPEN DOOR COMMAND

Function when LED is ON Rescue drive from MAP is ON (270). Input XM11/2 on LCECPU pos. 375. Car communication network is working. Lift well communication network is working.

Normal status OFF

YELLOW

ON ON

GREEN GREEN

+ 24 V DC car and lift well voltage is OK.

ON

GREEN

The LED is ON when the speed goes over 0.1 m/s while accelerating and goes OFF when the speed goes under 0.3 m/s while decelerating. One of the main contactors (201:1, 201:2) or the dynamic brake contactor (204) has not been released. Input XD1/3 on board 379. LCECPU has given main contactor activation command. Lift well doors are closed. Input XH2/3 on board pos. 379 has voltage. Car doors are closed. Input XC1/7 on board pos. 379 has voltage. Close the door command is given.

ON/OFF

YELLOW

ON/OFF

YELLOW

ON/OFF

YELLOW

ON/OFF

YELLOW

ON/OFF

YELLOW

ON/OFF

YELLOW

ON/OFF ON ON

YELLOW GREEN GREEN

ON/OFF ON/OFF ON/OFF

YELLOW YELLOW YELLOW

ON/OFF ON/OFF ON/OFF

YELLOW YELLOW YELLOW

ON/OFF ON/OFF ON/OFF

YELLOW YELLOW YELLOW

ON/OFF

YELLOW

Need for driving recognised. Drive unit is able to drive. Safety chain input XC1/5 on board pos. 379 is powered. Drive up command is given to the drive unit. Car is at top floor deceleration area. Car is at about +10 mm... -140 mm from floor level. Car is at door zone of front door. Car is at rear door zone. Car is at about -10 mm... +140 mm from floor level. Car is at bottom floor deceleration area. Car is at terminal floor area. Drive down command is given to the drive unit. Open door command is given.

Colour

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

323 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

LED PHOTOCELL

OPEN BUTTON

CLOSE FORCE LIMITER DOOR ZONE INDICATOR INHIBIT DOOR OPENING INHIBIT LANDING CALLS SPEED >0.6m/s (D68) SPEED >0.3m/s (D67) SPEED >0.02m/s (D66) SPEED >0.02m/s (D65) SPEED >0.3m/s (D64) SPEED >0.6m/s (D63)

Function when LED is ON

Normal status OFF

Colour YELLOW

OFF

YELLOW

OFF

YELLOW

ON/OFF

GREEN

OFF

YELLOW

Photocell LED is ON when there is something between doors. Inputs XB29/2 and XB31/2 on board LCECCB pos. 806. Door open button LED is ON when button is pressed. Input XC10/1 on board LCECOB pos. 32. Door closing force limiter is active. Inputs XB28/8 and XB30/8 on board LCECCB pos. 806. Car is at door zone. Signal is present even if the power supply is switched off. Door opening is inhibited with the switch beside this LED. Landing calls are inhibited with the switch beside this LED. Car speed more than 0.6 m/s, up direction.

OFF

YELLOW

ON/OFF

RED

Car speed more than 0.3 m/s, up direction.

ON/OFF

GREEN

Car speed more than 0.02 m/s, up direction.

ON/OFF

GREEN

Car speed more than 0.02 m/s, down direction. Car speed more than 0.3 m/s, down direction. Car speed more than 0.6 m/s, down direction.

ON/OFF

GREEN

ON/OFF

GREEN

ON/OFF

RED

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

324 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.8

Fuses and LEDs on LOP-230 board Fuse F1 Safety chain 230 V F2 Safety chain, brake and fan supplies F3 Door supply

Size/type 1 A/T (5x20 mm) 6.3 A/T (5x20 mm)

LED

Normal

F2 OK

ON

2 A/T (5x20 mm)

F3 OK

ON

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

325 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

D.9

Fuses on LCEREC board Fuse F4 Car and shaft 24 V F5 Control voltage 24 V F6 & F7 Short circuit protection of transformer F8 24 V Car and shaft (optional if > 10 floors)

Size/type 4 A multi fuse 4 A multi fuse 6 A/500 V (10x38 mm) 8 A multi fuse

DRAFT Copyright ©2012 KONE Corporation All rights reserved.

326 (340)

AM-01.01.250 (Draft A) 2012-08-28

KONE MonoSpace® 3.0 Installation Instruction

APPENDIX E. ELEVATOR SHAFT WIRING WITH TRUNKING E.1

Trunking and shaft lighting

NOTE: For optimal lighting install the light units to horizontal position (if possible) with the lamps pointing downwards. Install the lowest light unit to vertical position.

max 0.5m

1. Install the trunking and elevator shaft lighting. 2. Drill holes for signalling cable and door lock cable fixings at each landing. open trunking cable entries.

6m

m

1076609.wmf

max. 0.5m

6m

m 50