2_5_Commissioning__Integration_MOP__BBU_(FSIH)__RRU_(FZHJ)_D512241255_Rev8.pdf

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 1 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) Project Name:

Sprint 2.5 TD-LTE

Customer Name: Document No. Version

Sprint D512241255 0.8

Document Type:

Method of Procedure

Document Number:

D512241255

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 2 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Document Revision History Date

Rev.

3/17/2014

1

4/10/14 7/15

Originator

Summary of Change

Pete Mork / Steve Elliston

First draft

2

Jason Mackel

Language added for SCOP docs and ATP

3

Pete Mork

RL45 Updates

8/15/14

4

James Vu

Factory SW to PCD4 steps Updates

08/20/14

5

Fahad Faridi

Updates for commissioning and post commissioning activities. Included escalation matrix.

8/20/14

6

Jason Mackel

Updated ART requirements in section 4 and added ART document in appendix

09/02/14

7

James Vu/ Fahad Faridi

 Step 11: Added removing IPsec policy during 1st commissioning  Step 42,48, 49: Include reference for Site Master sheet for RET angles  Page 31 [#4] : Added details for picture upload fields in NOLS

9/3/14

8

James Vu/ Fahad Faridi

 Step 19: Added new route in routing table to support Traffica  Step 20 - 25: Added steps for configuring RF parameters during 2nd commissioning.  Step 5 - 8: Added steps to check for CPRI interface using script.

Sprint Document Approval Rev.

Role

Name

Signature Date

The information in this document is subject to change without notice and describes only the product defined in the introducti on of this documentation. This document is intended for the use of Nokia Solutions and Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified, or transmitted in any form or means without the prior written permission of Nokia Solutions and Networks. The document has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Solutions and Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this document concerning the suitability, capacity, or performance of the mentioned hardware or software products are given “as is” and all liability arising in connection with such hardware or software products shall be defined conclusively in a separate agreement between Nokia Solutions and Networks and the customer. However, Nokia Solutions and Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Solutions and Networks will, if deemed necessary by Nokia Solutions and Networks, explain issues which may not be covered by the document. Nokia Solutions and Networks will correct errors in the document as soon as possible. IN NO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENT OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY MONETARY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This document and the product it describes are considered protected by copyrights and other intellectual property rights according to the appli cable laws. Wave logo is a trademark of Nokia Solutions and Networks Oy. Nokia is a registered trademark of Nokia Corporation. Other mentioned this document may be trademarks of SITE their respective owners, and they are mentioned for identi fication purposes only. Copyright © product Nokianames Solutions andinNetworks 2014 ENGINEERING Copyright © Nokia Solutions and Networks 2014. All rights reserved. D512241255 0.8

Page 2 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 3 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Table of Contents 1.

2.

3.

4. 5. 6. 7. 8. 9. 10.

Introduction ......................................................................................................................................... 4 1.1 MOP Contacts .......................................................................................................................... 4 1.2 NSN Project Escalation Contacts .............................................................................................. 4 MOP Work Tasks Summary, Responsibilities & Assumptions ......................................................... 6 2.1 C&I Pre-requisites ..................................................................................................................... 6 2.2 Commissioning and Integration Tasks ....................................................................................... 6 2.3 Training & Insurance Requirements .......................................................................................... 7 Work Task Execution .......................................................................................................................... 7 3.1 Required Tool & Test Equipment Check List.............................................................................. 7 3.2 Detailed Work Task Instructions ................................................................................................ 7 Table 3: NSN project contact list .......................................................................................................... 26 Post C&I checklist and SCOP UPLOAD............................................................................................ 28 Appendix a: C&I Troubleshooting Guide ......................................................................................... 33 Appendix B: ENB LOCK UNLOCK PROCEDURE ............................................................................. 33 Appendix C: TCP/IP Settings ............................................................................................................ 33 Appendix D: FSIH Port Diagram ....................................................................................................... 34 Appendix E: ART Overview ............................................................................................................... 34 Appendix F: SITE MASTER SHEET (For RET Angles) ..................................................................... 34

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 3 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 4 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

1. INTRODUCTION This document details the Method of Procedure (MOP), including work tasks and checks required to successfully commission and integrate the NSN TD-LTE BBU (FSIH) and RRUs (FZHJ), collectively known as eNodeB (eNB). This document is generated by NSN and shared with Sprint for consultation and Sprint approval. This document and information contained within shall not be shared or distributed outside of Sprint without Nokia Solutions and Networks prior written consent. Nokia Solutions & Networks (NSN) shall not be responsible or accountable for any information taken from this document which is subsequently used by any other party other than Sprint and NSN directly. If there are any concerns or changes required to this MOP, this should be raised to the identified contacts in this document within 2 working days of identifying.

1.1 MOP Contacts Contact the following when there are any concerns, queries or corrections required to this MOP. In all correspondence, reference the MOP document and version # and the applicable page(s). Table 1: MOP contact list.

Company

Name

Contact Email

Fahad Faridi

[email protected]

Sprint Nokia

Note: Above is for documentation purposes, responses may take 2-5 working days. For training and technical support, please contact your relevant support organizations.

1.2

NSN Project Escalation Contacts If there are issues, problems or concerns that are not being addressed by installation engineers, the Nokia project manager should be contacted immediately. In the unlikely event that the NSN project manager is not addressing issues, problems or concerns, an escalation should be made to one of the regional project directors. For all technical issues (C&I / ATP failures) Nokia Tier 2 Support should be contacted according to corresponding markets listed in Table 3: NSN project contact list. If Nokia Tier 2/OSS Support is not addressing issues, problems or concerns, an escalation should be made to one of the following Technical project managers. Table 2: Technical escalation contact list.

Company

Name

Title

Contact Phone

Nokia

Fahad Faridi

National Technical Manager

847-531-3137

Nokia

Frederick Mckinlay

RAN Technical Manager

425-205-7818

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 4 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 5 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Table 3: NSN project contact list.

Market South West Florida Tampa Jacksonville

Nokia Market PM

Nokia Regional Director

Joe Meilinger Cell: 407-284-7812

Nokia Tier 2 Support

Siraj Sindhi Cell: 2149148768

Orlando Nashville West Kentucky Memphis Atlanta / Athens Miami / West Palm Arkansas Mississippi New Orleans Kansas

Dave Romagnia Cell: 615-335-6815

OSS Support

Jeffery San-Luis ROC Central Number : 972-374-0871

Jason Mackel Cell: 954-214-2960 James Vu Cell: 469 879 3692

Carla Pratcher Cell: 770-337-1686 Steve Emberlin Cell: 954-439-5353

Rick Reveley Cell: 313-408-7350

Missouri Albuquerque Austin South Texas

Rafe Schenouda Cell: 972-693-6324

Steve Holden Cell: 571-201-2139

San Antonio Houston DFW West Texas

Manohar Gotgi Cell: 214 912 2154

Anthony Chavez/ Ramiro Alaniz ROC Central Number : 972-374-0871

Brandon Zobisch Cell: 405-762-3737 Mike Moser Cell: 972-693-8482

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 5 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 6 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

2. MOP WORK TASKS SUMMARY, RESPONSIBILITIES & ASSUMPTIONS 2.1 C&I Pre-requisites Commissioning and Integration (C&I) of the 2.5 BBU/RRUs shall not commence until all 2.5 hardware preparations and installation has been successfully completed, and the site is ready for C & I to commence. In addition to work Sprint or Ericsson may need to carry out (preparation), there is an NSN installation Method of Procedure (MoP) for each of the following site types, which should be referenced concerning what is required to make the site ready for 2.5 C&I. 1. Ericsson Outdoor cabinet (RBS 6102) 2. Ericsson Indoor cabinet (Sprint shelter site) 3. NSN Outdoor Growth Cabinet (sites that required an expansion cabinet) The C&I Engineer must have access to the site specific SCF file required for commissioning the site (Downloaded to PC) before C&I can start. The C&I Engineer must have a copy of the Sprint RFDS.

2.2 Commissioning and Integration Tasks The tasks indicated in the table below represent the items to be conducted by the BTS engineer/technician and will result in the commissioning and integration of the site. #

Work task

Responsible for completing work

Work carried out during

1

Take before photos inside the Ericsson 6102 cabinet clearly displaying the left side, right side, and CSR.

NSN

D

2

Verify fiber connectivity to ports 1-6 on FSIH

NSN

D

3

Power on FSIH (BBU), FYGE (GPS box), and FZHJ (RRU) units

NSN

D

4

Successfully log into the FSIH

NSN

D

5

Commission TRS and wait until all FZHJ are detected and FYGE self survey is completed

NSN

D

6

Commission BTS

NSN

D

NSN

D

NSN

D

NSN

D

7 8 9

Complete software upgrade of FSIH and FZHJ units using the latest project approved software release Move optical cables to the required ports per approved software release Commission all ALDs (Antenna Line Device) including RET ACUs (Antenna Control Unit)

10

Save a copy of the Site Commissioning File

NSN

D

11

Save a copy of the Backup Commissioning File

NSN

D

12

Save a copy of the BTS Site Manager Snapshot (Current Data Only)

NSN

D

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 6 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 7 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) 13

Call ROC (OSS Support) for pushing eCSFB Parameters before ATP testing

NSN

D

14

Execute ATP and upload logs

NSN

D

M = Maintenance window (service effecting work activity) D = Done at any time, including during normal business hours or prior to maintenance window

2.3

Training & Insurance Requirements Suitable training shall be completed and passed (certified to use this MOP) by all C&I engineers executing this MoP. All persons carrying out works on site shall be suitability insured.

3. WORK TASK EXECUTION 3.1 Required Tool & Test Equipment Check List

Check status

#

Tool or test equipment

1

Laptop with current project approved eNB software and BTS Site Manager

2

Ethernet cable

3

Fiber Cleaner (Cletop or similar)

(OK, NOK, N/A or note)

3.2 Detailed Work Task Instructions Upon arrival at site, follow these instructions step by step.

Step

Step Description

Task Status Arrival On-site

1

Call the Sprint NOC at 1-866-400-6040 Options 2 + 6 - Identify site ID & inform NOC of planned activities - Request NOC engineer to identify status of CDMA & LTE equipment for alarms - Record any alarms observed by the NOC engineer - Sign in on the site log book - Locate the hybrid & fiber test results left by the GC (Tower Crew) - Locate the Antenna and RET Serial Number information left by the GC (Tower Crew)

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 7 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 8 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) 2

Visually inspect the hardware installation for obvious errors or issues

3

Take pre-C&I photographs. Photo of cabinet with 2.5 units and cabling (1-3 photos).

Software Verification

1

2

Connect laptop to the FSIH System Module (BBU) with standard Ethernet cable. Connect one end to the PC Ethernet port and the other end to the FSIH System Module (BBU) LMP port. (See Appendix C for TCP/IP settings)

Launch BTS Site Manager from your PC Log in to BTS Site Manager. IP Address = Local (No IP address required if connecting locally) Username = Nemuadmin Password – nemuuser

3

Click “Accept” to continue

Check Software version which come pre-installed with FSIH: Pre-installed version

BTS Site Managers Required

Next Step

LNT4.0_ENB_1311_349_96

LNT4.0_BTSSM_1311_062_00 LNT4.0_BTSSM_1311_095_00

5

4 Other

Contact Nokia Centralized Support Team for further instructions before proceeding

Important: Un-install any version of BTS Site Manager not listed above before proceeding to next step.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 8 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 9 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Hardware Detection 5

Copy and unzip AutoScriptForCustomerUsing (0.0.11).7z to your laptop. AutoScriptForCustomerUsing (0.0.11).7z is included in the C&I Document Pack zip file. Double click file CheckLoadIndication4OBSAI.bat following output will display when script execution will complete

6

Once CheckLoadIndication4OBSAI.bat is completed check the output.txt file. The output.txt file of the script can be found in same folder as the script. There will be one of two messages in the output.txt file. 

OBSAI unit, no need to change!



CPRI unit, change to OBSAI now!

7

8

If the message in the output.txt is CPRI Unit, change to OBSAI now!, please return the serial and version number to [email protected].

9

Make sure that all 6 fiber connections from FZHJs (RRHs) are connected to ports 1 to 6 on FSIH (System Module)

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 9 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 10 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Commission TRS by selecting “Commissioning “, select “Template”, unchecked “BTS”, Click “Browse” and go to where the SCF file is stored, click on the file to load.

10

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 10 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 11 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Click Next until you reach IP Security page. If there is a IP Security Policy listed under Policies, Select Policy and Click Delete Policy

11

Click “next” to “Send Parameters” page then click “ Send Parameters” 12

13

Wait for GPS self survey to complete (This step may take around 30 minutes)

Check BTS status and RRU status after auto reset. After auto reset the GPS will come up and site goes to synchronized status. Wait for up to 10 min, RFM will be detected but there is fault 23 reported due to incompatible version. 14

The BTS status should be integrated. If all hardware is not detected, do not begin software upgrade or commissioning. (Refer to Appendix A: C&I Troubleshooting Guide)

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 11 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 12 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Commissioning From the main menu on the left click on “Commissioning”.

15

Select the following and browse to your site specific SCF (Site Configuration File)

16

17

Select the SCF file that was created for the site you are commissioning. Verify the site information on the right side “File Details” is correct and click “open”.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 12 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 13 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Click Next until you reach IP Security page. If there is a IP Security Policy listed under Policies, Select Policy and Click Delete Policy

18

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 13 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 14 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) Click Next until you reach IPv4 Routing page. Add a new route based on following settings: Destination: Lookup IP address in Table A according to your market Netmask : 255.255.254.0 Gateway: Same as management plane CSR gateway (see figure below)

19

Market South West Florida Tampa Jacksonville Orlando Nashville West Kentucky Memphis Atlanta / Athens Miami / West Palm Arkansas Mississippi New Orleans Kansas Missouri Albuquerque Austin South Texas San Antonio Houston DFW West Texas

IP Address 10.88.43.0 10.88.43.0 10.88.43.0 10.88.43.0 10.88.43.0 10.88.43.0 10.88.43.0 10.88.43.0 10.88.43.0 10.88.43.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0 10.88.46.0

Table A

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 14 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 15 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Click Next until you reach the Cell Resources page. - Check and fill in antennas (FZHJ 1.7.1) data for Alpha Sector (49) as below:

20

21 22 23

-

Check MIMO settings and select Dynamic Open loop MIMO.

-

Check Carrier Power and select 5W as below:

Repeat step 15 for Beta sector (50), FZHJ 1.9.1 antennas Repeat step 15 for Gamma Sector (51), FZHJ 1.11.1 antennas Click Next to reach the LTE Carriers Page enter Frequency Band, Bandwidth, and EARFCN for each sector as below:

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 15 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 16 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Click Next until you reach the Antenna line management menu and verify that “3GPP/AISG Communication” is enabled on antenna line 1 for each RRH. This will allow the RET ACU to be detected after the site is commissioned. DC Voltage should be unchecked.

24

25

Click Next until you reach Antenna Line Settings page enter data as below for all antennas:

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 16 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 17 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Click Next until following page with all Parameters will be reached

26

Modify following parameters under each LNCEL: Object Name 27

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 17 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 18 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Parameter Name Select R81xCsfbEnforced

Select false

Select false

Click Next until you reach the page that allows you to send parameters and click the “Send Parameters” button.

28

29

Once commissioning is complete, you will have the option to save a copy of the commissioning report. Select the “Save As” option and save this report to your PC

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 18 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 19 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ) as part of the site acceptance close out package.

Click on the object FYGA and verify GPS is receiving signal from satellites. Verify a minimum of 5 satelites are required with minimum signal strength of 6. If minimum satellite requirements are not met, check the hardware installation. If hardware installation is correct, check the position of the GPS antenna – and that it has a clear view to the sky. Contact PM if GPS postion is a concern.

30

Software Upgrade

31

From the main menu click “Software”, then “Update Software to BTS”. Update the software to the project approved software release (LNT4.0_BTSSM_1311_536_03). Note: Wait 10 minutes after software upgrade is 100% COMPLETE before proceeding to next step.

32

Verify there is no “Software Incompatibility” alarms post software upgrade. If this alarm is encountered, first move the fibers according to step 22 and then follow the steps to clear this alarm.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 19 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 20 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Verify no other alarms are present before proceeding to the next step. 33

Move optical cables from ports 1,2 ( alpha sector) to 7,8; 3,4 (beta sector) to 9,10 and 5,6 ( gamma sector) to 11,12 as shown in following diagram:

34

NOTE: If you encounter Software incompatibility alarm repeat step 19. A second software upgrade is required to clear this alarm. 35

After FZHJs are detected, re-commission site using Reconfiguration option.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 20 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 21 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

After commissioning is completed verify that correct ports are being shown in BTS Site Manager after clicking each FZHJ.

36

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 21 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 22 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

37

Verify “OAM connected” is displayed in lower right corner of BTS Site Manager. If OAM connected does not display within 10 minutes refer to troubleshooting appendix.

Verify “TRS Commissioned” is displayed in lower right corner of BTS Site Manager 38 Verify “On Air” is displayed in lower right corner of BTS Site Manager 39 Click on each hardware object FSIH, FBIH, and FZHJ and verify working state is “working”. Example FZHJ displayed below.

40

41

Verify all sectors are “On Air” and the site has no alarms other than ALD (Antenna Line Device). ALD alarms will be resolved in the next steps during RET commissioning. If you encounter any other alarms do not proceed. Please refer to Appendix A: C&I Troubleshooting Guide for issue resolution details.

RET Commissioning Commission all RET ACU (Antenna Control Units). From the main menu on the left click on “Commissioning”.

42 Note: Electrical tilts for RETs are set in the warehouse before the antennas are shipped to market. If no new RET information is provided please commission RETs with the current settings. If your site is listed in the “Site Master sheet” please commission the RETs and then reset the angles to the new angels

43

Select the following option to reconfigure the BTS. This allows you to commission the RETs only. It is highly recommended to save a Backup Commissioning file by clicking the “Backup Commissioning Files” button before proceeding.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 22 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 23 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Click “Next” until you reach the RET Settings page. Assign each RET to the corresponding antenna

44

45

After each RET has been assigned to its corresponding antenna click “Next” until you reach the send parameters page. Click “Send Parameters” (Only Changes is default).

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 23 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 24 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Once the RETs are commissioned they need to be calibrated and the electrical tilt needs to be set per the Site Information Package. To calibrate each RET ACU, go to the main menu Antenna and click on “RET Settings” 46

47

Select the RET you wish to calibrate by clicking the check box and then click send. NOTE: You can select all RETs for calibration at the same time.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 24 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 25 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

After the RETs are calibrated you will be able to set the desired electrical down tilt. Double click inside the “Angle” box, enter the desired angle value according to Site Master Sheet [APPENDIX F] and then click send.

48

49

After the RETs are commissioned, calibrated, and electrical tilts are set according to the Site Master Sheet, verify the eNodeB is alarm free. Example below.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 25 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 26 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Post Commissioning Activities

50

From the main menu, click on the Snapshot button and save a current snapshot of the BTS (Current Data Only option is OK). This will be required for site acceptance and close out package.

Notify OSS Support to initiate eNB Object Creation and eCSFB Parameter Push in NetAct OSS (EMS). 51

OSS Support numbers are listed in following section of this MOP 1.2

NSN Project Escalation Contacts Table 3: NSN project contact list

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 26 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 27 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Verify if eCSFB push is successful by confirming that values for following parameter under each LNCEL object are non zero:

52

Note: If above parameters are zero wait for 10 minutes and re-check. If they are still zero call OSS support numbers.

Proceed to the NSN TD-LTE ATP MOP and perform Site Acceptance testing using TAPAS. 53 Important: ATP will fail if previous step is not performed (eCSFB Parameter push and verification) After ATP completion and before leaving site lock all 3 sectors by changing Administrative State = Locked, under Commissioning LNCEL parameters. 54 For more detail see MOP titled Nokia_ENB_Lock_Unlock_MOP – Section 1.2 [Ref: Appendix B]

55

Enable DRX by following step 16 and selecting true

ENB final state (before leaving site) should be: OAM Connected /Integrated /TRS Commissioned 56

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 27 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 28 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

4. POST C&I CHECKLIST AND SCOP UPLOAD Use this checklist to verify C&I was successfully completed. Table 3: Post checks installation steps.

Task Status Step

Complete [C]

Step Description

Not Complete [NC]

1 Prior to leaving the Site the ENB engineer will verify the following items have been comlpleted and the status of each the status of all the deliverables has been forwarded to the market PM.

2

Upon completion of the Installtion of the NSN components, as well as the Integration and commissioning the EnB enginner will collect closeout pictures and upload them to ART. ART is a program that is utilized by Sprint to collect closeout documents and a subscription will be required to access the system. If you need an account set-up, please contact your market project manager;

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 28 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 29 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Picture size will be a minimum of 1280 x 720. Camera to have 8megapixel capability. Link to ART:

https://nvart.sprint.com/

 Art overview can be found in Appendix (#)

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 29 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 30 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Description of Photos to be collected and uploaded to ART

3

Pictures will be labeled, compressed to a zip file and uploaded to the documents folder for that particular site. It is expected tat the photos will be uploaded the same day that they taken. A notification e-mail will be sent to the CPO organization and the market PM.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 30 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 31 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Open site and click documentation

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 31 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 32 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

Load pictures to C&I folder

Choose following options when uploading pictures to Site folder

4

5

Upon leaving the site Call the Sprint NOC at 1-866-400-6040 and informed them you leaving the site.

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 32 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 33 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

5. APPENDIX A: C&I TROUBLESHOOTING GUIDE

Sprint_C&I_Troubles hooting_Guide_v2.xlsx

6. APPENDIX B: ENB LOCK UNLOCK PROCEDURE Nokia_ENB_Lock_Unl ock_MOP_ver2.pdf

7. APPENDIX C: TCP/IP SETTINGS

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 33 (34)

Type of Guidelines -Number Revision - Number Document Method of D512241255 0.8 Procedure Page 34 of 34 Date: 9/4/2014 Title 2.5 Commissioning & Integration MOP - BBU (FSIH) & RRU (FZHJ)

8. APPENDIX D: FSIH PORT DIAGRAM

9.

APPENDIX E: ART OVERVIEW

ART Template for OEM ICI CCFA_Draft_0 6.pptx

10. APPENDIX F: SITE MASTER SHEET (FOR RET ANGLES) SPRINT-MasterList-2 .5GHz.xlsx

Copyright © Nokia Solutions and Networks 2014 D512241255

SITE ENGINEERING 0.8

Page 34 (34)