2010 Catalog for Atlas Supply
Short Description
catalog...
Description
DESIGN, MANUFACTURE, & SUPPLY SPECIALISTS OF CONCRETE FORMING & SHORING SYSTEMS CONCRETE ACCESSORIES, TILT-UP, PRECAST AND CONCRETE CONSTRUCTION CHEMICALS & RESTORATION PRODUCTS SALES AND RENTALS With an emphasis on concrete related products, Atlas Construction Supply, Inc. is a supplier supportive to General Contractors and Concrete Sub-Contractors & Precasters. Atlas Construction Supply, Inc. and its affiliated names of The Atlas Companies, Atlas Forming Systems, and Atlas Tech Products, present the design, fabrication, and supply of concrete forming and shoring systems, along with other accessories and construction products. We, at Atlas Construction Supply, identify ourselves as Contractor Committed. Our commitment is centered on an understanding that our purpose for existence rests on effectively serving our customers’ construction needs. To provide such a service, we continuously from our inception in 1980, have recognized the effectiveness achievable for the benefit of our customers by coupling product with people. All these presented products have significant value added through representation by the Atlas Construction Supply employee team. Our people, with considerable product and function knowledge, are guided by a corporate directive to use their own best judgement with their focus on their customers at all times. This company was made to be advised, influenced, and directed by our customers... A Customer Company. Service...Quality...Commitment.
ATLAS LOCATIONS: San Diego: Corporate Office 4640 Brinell St. San Diego, CA 92111 (858) 277-2100 fax (858) 277-0585
Los Angeles 2745 Raymond Ave. Signal Hill, CA 90755 (562) 595-1006 fax (562) 595-4117
Phoenix 1611 South 27th Ave. Phoenix, AZ 85009 (602) 256-0600 fax (602) 256-0687
Las Vegas 4840 W. Hacienda Ave. Las Vegas, NV 89118 (702) 227-6800 fax (702) 222-0488
Denver 4800 Race St. Denver, CO 80216 (303) 298-7777 fax (303) 298-7778
San Francisco (510) 353-0100
www.atlasform.com
Mexico 001 (877) 586-2100
1
MANUFACTURER
PRODUCTS
Atlas Forming & Shoring Systems
ABT, Inc.
AL-SPEED® Frame, A-Deck Shoring System, Truss & Column Mounted Flying Deck Forms, Garage Beam Forms, ACS Panel Wall Form, Atlas Aluminum & Wall Beam Systems, Ganged & Handset Column Forms. Concrete Form Form Panels, LVL EDGE Form, Post Shores, Safety Rail Post, Bridge Overhang Bracket, Waler Jacks. Form Releases, Curing Compounds, Sealers, Bondbreakers, Epoxies, Grouts, Repair Mortars, Underlayments, Toppings & Shake-On Floor Hardeners. Concrete Restoration-Polymer Concrete Overlays & Methacrylates. Precast Trench Drain Systems, Polydrain, Trench Former.
Arcis / Access Tile
ADA Detectable Warning Panels.
Aztec Concrete Accessories
Rebar Supports, Concrete Dobies, Edge Forms & Adhesives.
BMD, Inc.
Nails & Fasteners, Masking & Duct Tape.
Chapin
Industrial Concrete Sprayers.
Dayton Superior Deslauries
Formwork Accessories, Formliners, Tilt-Up & Precast Accessories, Bar Supports, Rebar Splicing Systems, Chemical & Repair Products. Column Forms, Capitol Forms, Box Voids.
Durajoint
PVC Waterstops, Adhesive Waterstops & Accessories.
Fortifiber Corp.
Curing & Protection Paper, Moistop Vapor Barrier.
General Technologies, Inc. (GTI)
Slab Bolsters, Bar Chairs & Post-Tensioned Slab Products.
Global Mfg. / Viber-Kelley
Internal & External Vibrators, Concrete Placing Equipment.
Greenstreak / Vinylex
Speed Dowels / PVC Waterstops, Plastic Control Joints, Chamfer.
Henry Co.
Synko-Flex & Hydro-Flex Adhesive Waterstops.
Hogan Company
Steel Stakes, Curb Forms & Accessories.
McTech Group
Ultracure Curing Blankets, EZ Cover, EZ Dowel Load Transfer System
MFG Construction Products
Fiberglass Column Forms & Pans, Waffle Slab & Custom Forms.
Meadow Burke Multiquip Construction Equipment
Forming Accessories, Snap Ties, Taper Ties, Coil Rod, Anchors, Inserts, Rebar Supports & Other Accessories. Pumps, Mixers, Power Trowels, Screeds & Generators.
Proline
Decorative Concrete Stamps, Color Hardeners, Stains, Etc.
Quikrete
Cement, Concrete, Sand, Aggregates & Other Building Materials.
Roseburrough Tool Co.
Concrete Tools & Accessories.
Sonoco Products
Sonotube Forms & Void Forms.
Symons
Concrete Accessories & Forming Products.
TRM Manufacturing
Polyethylene Film Products.
Unitex
Epoxies, Form Releases, Bondbreakers, Surface Retarders & Specialites.
Universal Building Products Universal Forest Products
Concrete Accessories, Snap Ties, Taper Ties, Coil Rod, Anchors, Inserts, Stakes, Dowels & Dowel Baskets. Plywood, LVL, Lumber & Building Materials.
US Mix Products
Cement Products, Repair Mortars & Chemicals.
Western Insulfoam
Specialty & Standard Styrofoam (Custom Sizes Available).
Weyerhaeuser / TrusJoist
Edge Forming Materials, LVL, Other Lumber & Building Materials.
W.R. Meadows
Chemicals, Expansion Joint & Plastics, Vapor Retarder & Paving Products.
Atlas Concrete Accessories Atlas Tech Products
2
www.atlasform.com
TABLE OF CONTENTS GENERAL TERMS & SAFETY NOTES 10-FORMING & SHORING
SECTION 10 - FORMING & SHORING SYSTEMS AL-SPEED® SHORING FRAME, A-DECK POST SHORE & JOIST DROPHEAD SHORING SYSTEM, COLUMN MOUNTED & TRUSS FLIERS, GARAGE BEAM SYSTEM, ACS PANEL WALLFORM, GANGED ALUMINUM/ LVL WALLFORMS, RADIUS WALL FORMS, HANDSET WALL PANELS, COLUMN FORMS.
20-FORMING ACCESSORIES
SECTION 20 - FORMING & SHORING ACCESSORIES POST SHORES, SAFETY RAIL POSTS, OVERHANG BRACKETS, SNAP TIES, TAPER TIES, COIL ROD, FORMING PLYWOOD, ENGINEERED LUMBER, FORMLINER.
30-CHEMICALS & REPAIR
SECTION 30 - ATLAS TECH PRODUCTS- CHEMICALS & REPAIR PRODUCTS FORM RELEASE AGENTS, CURING COMPOUNDS, SEALERS, BONDBREAKERS, EPOXIES, GROUTS, REPAIR MORTARS, DECK OVERLAYS & CRACK SEALERS, SHAKE-ON FLOOR HARDENERS, DECORATIVE CONCRETE SYSTEMS.
40-REBAR SUPPORTS
SECTION 40 - REBAR SUPPORTS & ACCESSORIES SLAB BOLSTER, BAR CHAIRS, WHEELS, DOBIES, BAR COUPLERS & SPLICE SYSTEMS, TIE WIRE, DOWEL BASKETS.
50-FLATWORK ACCESSORIES
SECTION 50 - FLATWORK ACCESSORIES EDGE FORM, STEEL STAKES, TRENCH DRAIN, EXPANSION JOINT FILLERS, EXPANDED POLYSTYRENE, VAPOR RETARDERS, WATERSTOP, DETECTABLE WARNING PANELS.
60-PRECAST & TILT-UP
SECTION 60 - TILT UP & PRECAST PRODUCTS PICK-UP INSERTS, BRACES & BRACE ANCHORS, LIFTING HARDWARE
PRODUCTS
VOID FORM, AREA WELLS, FABRICATED STEEL POSTS & BEAMS, METAL DECKING.
80- TOOLS & PLACING
SECTION 80 - TOOLS & PLACING EQUIPMENT MIXERS & PUMPS, CONCRETE BUCKETS, VIBRATORS, SPRAYERS, TROWELS & FINISHING EQUIPMENT HAND TOOLS.
INDEX
www.atlasform.com
70- FOUNDATION
SECTION 70 - FOUNDATION PRODUCTS
3
OSHA REGULATIONS FOR FORMWORK AND SHORING Here and on the following page are reproduced the United States Occupational Safety and Health Act provisions regulating concrete construction, concrete forms, and shoring. This material is taken from the U.S. Department of Labor: “Occupational Safety & Health Administration”, 29CFR, Part 1926 (as published originally in the Federal Register, V. 37, No. 243, Dec. 16, 1972). It is the contractor’s responsibility to confirm the following regulations have not been revised, amended or superceded; or that any additional Local, State, or Federal regulations may be applicable for the location of the project. Subpart Q-Concrete and Masonry Construction
based on information received from a person who is qualified in structural design, that the structure or portion of the structure is capable of supporting 1926.760 Scope, application and definitions the loads. applicable to this subpart. (b) Reinforcing steel. All protruding reinforcing steel, onto and into which employees (a)Scope and application. This subpart sets forth could fall, shall be guarded to eliminate the hazard requirements to protect all construction employees of impalement. from the hazards associated with concrete and (c) Post-tensioning operations. (1) No masonry construction operations performed in employee (except those essential to the postworkplaces covered under 20 CFR part 1926. In tensioning operations) shall be permitted to be addition to the requirements in subpart W, other behind the jack during tensioning operations. (2) relevant provisions parts 1910 and 1926 apply to Signs and barriers shall be erected to limit concrete and masonry construction operations. employee access to the post-tensioning area (b) Definitions applicable to this subpart. In during tensioning operations. addition to the definitions set forth in 1926.32, the (d) Riding concrete buckets. No employee shall following definitions apply to this subpart. be permitted to ride concrete buckets. (1) Bull float means a tool used to spread out and (e) Working under loads. (1) No employee shall smooth concrete. be permitted to work under concrete buckets while (2) Formwork means the total system of support for buckets are being elevated or lowered into freshly placed or partially cured concrete, including position. (2) To the extent practical, elevated the mold or sheeting (form) that is in contact with concrete buckets shall be routed so that no the concrete as well as all employee, or the fewest number or employees, supporting members including shores, reshores, are exposed to the hazards associated with falling hardware, braces, and related hardware. concrete buckets. (3) Lift slab means a method of concrete (f) Personal protective equipment. No construction in which floor, and roof slabs are cast employee shall be permitted to apply a on or at ground level and, using jacks, lifted into cement, sand, and water mixture through a position. pneumatic hose unless the employee is (4) Limited access zone means an area wearing protective head and face equipment. alongside a masonry wall, which is under construction, and which is clearly demarcated {53 FR 22643, June 16, 1088, as amended at 59 to limit access by employees. FR 40730, August 9, 1994} (5) Precast concrete means concrete members (such as walls, panels, slabs, columns, and beams) 1926.702 Requirements for equipment and which have been formed, cast, and cured prior to tools. final placement in a structure. (6) Reshoring means the construction (a) Bulk cement storage. (1) Bulk storage bins, operation in which shoring equipment (also called containers, and silos shall be equipped with the reshores or reshoring equipment) is placed, as the following: (i) Conical, or tapered bottoms; and (ii) original forms and shores are removed, in order to mechanical or pneumatic means of starting the support partially cured concrete and construction flow of material. loads. (2) No employee shall be permitted to enter (7) Shore means a supporting member that resists storage facilities unless the ejection system a compressive force imposed by a load. has been shut down, locked out, and tagged (8) Vertical slip forms means forms which are to indicate that the ejection system is not to be jacked vertically during the placement of concrete. operated. (9) Jacking operation means the task of lifting a (b) Concrete mixers. Concrete mixers with one slab (or group of slabs) vertically from one cubic yard (.8m3) or larger loading skips shall location to another (e.g., from the casting location be equipped with the following: (1) A mechanito a temporary (parked) location or it its final cal device to clear the skip of materials; and (2) location in the structure), during the construction Guardrails installed on each side of the skip. of a building/structure where the lift-slab process is (c) Power concrete trowels. Powered and rotating being used. type concrete troweling machines that are manually guided shall be equipped with a control {53 FR 22643, June 16, 1988, as amended at 55 switch that will automatically shut off the power FR 42328, October 18, 1990} whenever the hands of the operator are removed from the equipment handles. 1926.701 General Requirements (d) Concrete buggies. Concrete buggy handles shall not extend beyond the wheels on either side (a) Construction loads. No construction loads shall of the buggy. be placed on a concrete structure or portion of a (e) Concrete pumping systems. (1) Concrete concrete structure unless the employer determines, pumping systems using discharge pipes shall
4
www.atlasform.com
be provided with pipe supports designed for 100 percent overload. (2) Compressed air hoses used on concrete pumping system shall be provided with positive fail-safe joint connectors to prevent separation of sections when pressurized. (f) Concrete buckets. (1) Concrete buckets equipped with hydraulic or pneumatic gates shall have positive safety latches or similar safety devices installed and prevent premature or accidental dumping. (2) Concrete buckets shall be designed to prevent concrete from hanging up on top and the sides. (g) Tremies. Sections of tremies and similar concrete conveyances shall be secured with wire rope (or equivalent materials) in addition to the regular coupling or connections. (h) Bull floats. Bull float handles, used where they might contact energized electrical conductors, shall be constructed or nonconductive material or insulated with a nonconductive sheath whose electrical and mechanical characteristics provide the equivalent protection of a handle construction of a nonconductive material. (i) Masonry saws. (1) Masonry saws shall be guarded with semicircular enclosure over the blade. (2) A method for retaining blade fragments shall be incorporated in the design of the semicircular enclosure. (j) Lockout/Tagout Procedures. (1) No employee shall be permitted to perform maintenance or repair activity on equipment (such as compressors, mixers, screens or pumps used for concrete and masonry construction activities) where the inadvertent operation of the equipment could occur and cause injury, unless all potentially hazardous energy sources have been locked out and tagged. (2) Tags shall read Do Not Start or similar language to indicate that the equipment is not to be operated. 1926.703 Requirements for cast-in-place concrete. (a) General requirements for formwork. (1) Formwork shall be designed, fabricated, erected, supported, braced and maintained so that it will be capable of supporting without failure all vertical and lateral loads that may reasonably be anticipated to be applied to the formwork. Formwork which is designed, fabricated, erected, supported, braced and maintained in conformance with the Appendix to this section will be deemed to meet the requirements to this sections will be deemed to meet the requirements of this paragraph. (2) Drawings or plans, including all revisions, for the jack layout, formwork (including shoring equipment), working decks, and scaffolds, shall be available at the jobsite. (b) Shoring and reshoring. (1) All shoring equipment (including equipment use in reshoring operations) shall be inspected prior to the erection to determine that the equipment meets the requirements specified in the formwork drawings.
OSHA REGULATIONS CONTINUED (2) Shoring equipment found to be damaged such that its strength is reduced to less than that required by 1926.703(a)(1), shall not be used for shoring. (3) Erected shoring equipment shall be inspected immediate after concrete placement. (4) Shoring equipment that is found to be damaged or weakened after erection, such that its strength is reduced to less than that required by 1926.703(a)(1), shall be immediately reinforced. (5) The sills for shoring shall be sound, rigid, and capable of carrying the maximum intended load. (6) All base plates, shore heads, extension devices, and adjustment screws shall be in firm contact, and secured when necessary, with the foundation and the form. (7) Eccentric loads on shore heads and similar members shall be prohibited unless these members have been designed for such loading. (8) Whenever single post shores are used one on top of another (tiered), the employer shall comply with the following specific requirements for formwork: (i) The design of the shoring shall be prepared by a qualified designer and the erected shoring shall be inspected by an engineer qualified in structural design. (ii) The single post shores shall be vertically aligned. (iii) The single post shores shall be spliced to prevent misalignment. (iv) The simple post shores shall be adequately braced in two mutually perpendicular directions at the splice level. Each tier shall also be diagonally braced in the same two directions. (9) Adjustment of single post shores to raise formwork shall not be made after the placement of concrete. (10) Reshoring shall be erected, as the original forms and shores are removed, whenever the concrete is required to support loads in excess of its capacity. (c) Vertical slip forms. (1) The steel rods or pipes on which jacks climb or by which the forms are lifted shall be: (i) Specifically designed for that purpose; and (ii) Adequately braced where not encased in concrete. (2). Forms shall be designed to prevent excessive distortion of the structure during the jacking operation. (3) All vertical slip forms shall be provided with scaffolds or work platforms where employees are required to work or pass. (4) Jacks and vertical supports shall be positioned in such a manner that the loads do not exceed the rated capacity of the jacks. (5) The jacks or other lifting devices shall be provided with mechanical dogs or other automatic holding devices to support the slip forms whenever failure of the power supply of lifting mechanism occurs. (6) The form structure shall be maintained within all design tolerances specified for the plumbness during the jacking operation. (7) The predetermined safe rate of lift shall not be exceeded. (d) Reinforcing steel. (1) Reinforcing steel for walls, piers, columns, and similar vertical structures shall be adequately supported to prevent overturning and to prevent collapse. (2) Employers shall take measures to prevent
unrolled wire mesh from recoiling. Such measures may include, but are not limited to, securing each end of the roll or turning over the roll. (e) Removal of formwork. (1) Forms and shores (except those used for slabs on grade and slip forms) shall not be removed until the employer determines that the concrete has gained sufficient strength to support its weight and superimposed loads. Such determination shall be based on compliance with one of the following: (i) The plans and specifications stipulate conditions for removal of forms and shores, and such conditions have been followed, or (ii) The concrete has been properly tested with an appropriate ASTM standard test method designed to indicate the concrete compressive strength, and the test results indicated that the concrete has gained sufficient strength to support its weight and superimposed loads. (2) Reshoring shall not be removed until the concrete being supported has attained adequate strength to support its weight and all loads in place upon it. Readers are cautioned to refer directly to Title 8 of the California Code of Regulations and the Labor Code for detailed information regarding the regulation’s scope, specifications, and exceptions and for the other requirements that may be applicable to their operations. Forms, Falsework, and Vertical Shoring By definition concrete forms are considered falsework. Falsework, however, also includes support systems for forms, newly completed floors, bridge spans, etc., that provide support until appropriate curing or stressing processes have been completed. See below for selected SOs: A. Design of falsework 1. Concrete formwork and falsework must be designed, supported and braced to safely withstand the intended load…1717(a)(1) 2. Falsework design, detailed calculations, and drawings must be signed and approved by an engineer (Ca PE) if the falsework height (sill to soffit) exceeds 14 ft., if the individual horizontal span length exceeds 16 ft., or if vehicle or railroad traffic goes through the falsework...1717(b)(1)(A), (B) Note: for other falsework, approval may be provided by a manufacturer’s representative or a licensed contractor’s qualified representative…1717(b)(2)(B), (C) 3. Falsework plans must be available at the job site…1717(b)(3) 4. Minimum design loads are as follows:… 1717(a)(2) a) Total combined live and dead load: 100 psf b) Live load and formwork: 20 psf 5. Additional loads must be considered in the design…1717(a) B. Erection of falsework 1. Falsework must be erected on a stable, level, compacted base and supported by adequate pads, plates or sills…1717(b)(4) 2. Shore clamps (metal) must be installed in accord with manufacturer’s instructions…1717(d)(2) C. Inspection 1. Before pouring concrete on falsework requiring design approval, or an engineer (Ca PE) or the engineer’s representative must inspect for and certify compliance with plans…1717(c)(1) Note: For other falsework, the inspection and
www.atlasform.com
certification may be provided by a manufacturer’s representative or a licensed contractor’s qualified representative… 1717(c)(2)(B), (C) 2. A copy of the inspection certification must be available at the job site…1717(c)(3) D. Access to forms and falsework 1. Joists (51/2 in. wide) at not more than 36 in. o.c. may be used as walkways while forms are placed…1717(d)(3) 2. A plank (12 in. wide) may be used as a walkway while joists are placed…1717(d)(5) E. Fall protection Periphery rails are required as soon as supporting members are in place…1717(d)(4) Note: The area under formwork is a restricted area and must be posted with perimeter warning signs…1717(d)(6)(A) Guardrails Guardrails must be installed at the open sides of all work surfaces that are 71/2 ft. or higher, or workers must be protected by other fall protection or, if justified, by a valid fall protection plan…1621(a) A.Guardrailing specifications 1. Railing must be made from select lumber (or equivalent material) and must consist of: a) A wooden top rail that is 42 in. to 45 in. high that measures 2” x 4” or larger b) A midrail that is placed halfway between the top rail and the floor and that measures at least 1” x 6” c) A supporting post that measures at least 2” x 4” and is placed every 8 ft. …1620(a), (b), and (c) 2. All railings should be capable of withstanding a load of 200 lbs. 3. Railing constructed of substitute materials must meet the following requirements: a) The top rail must be smooth surfaced and 42 in. to 45 in. high above the floor, platform, etc. b) Protection between the top rail and the floor, platform, etc., must be equivalent to that provided by the standard midrail. 4. The top rail or midrail on scaffolding platforms may be substituted by the X-braces as specified in the scaffolding regulations…1644(a)(6) B. Guardrailing applications 1. Floor and roof openings: Floor and roof openings in any work surface must be railed or covered. The cover must be substantial, securely fastened, and able to withstand the load of workers or material. Covers must bear a sign stating-OPENING-DO NOT REMOVE… 1632(b), (e) Note: Roof openings include skylights unless they meet the requirements of 3212(e). 2. Wall openings: Wall openings must be guarded if there is a drop of more than 4 ft. and the bottom of the opening is less than 3ft. above the working surface…1632(j) 3. Elevators: Guardrails are required for elevator shaft openings that are not enclosed or do not have cages…1633 4. Falsework: Guardrails are required as soon as falsework-supporting members are in place…1717(d)(4) 5. Demolition: Wall openings must be guardrailed during demolition except on the floor being demolished and on the ground floor…1735(k).
5
SAFETY FACTORS AND SAFE WORKING LOADS In its continued development of accessories and related working parts for the construction industry, Atlas Construction Supply has placed increasing emphasis on ensuring that material supplied from its manufacturing plants meets or exceeds the normal safety requirements for concrete construction. New product designs are tested in our fabrication plant and/or independent testing laboratories, field tested and then modified as required before production begins. The safe working loads listed in this price list were determined from these tests. Do not use any Atlas Construction Supply product before first reading and understanding the instructions shown in the appropriate handbook. For safety, quality assurance must be extended to field personnel with the contractor making sure that his employees are properly instructed in the use and installation of Atlas Construction Supply products. The safety factor to be applied to a particular product is a variable, depending on the degree of hazard or risk involved in the application of that product. In concrete construction, various job site conditions can often increase the degree of risk. Concentrated loads of reinforcing bars or storage of other types of construction materials on formwork, unsymmetrical placement of concrete, uplift, impact, use of motorized carts, formwork height, jerking of a crane during the lifting of concrete elements, use of a crane not adequate for the job, bouncing of the concrete elements after it has been lifted, are some of the conditions that have a high risk factor. Safety factors must be increased by the user to reduce these risks. It is for this reason that we state the minimum safe working loads of our products. Atlas Construction Supply recommends that the provisions of the American National Standards Institute’s (ANSI A 10.9), OSHA (Occupational Safety and Health Administration Act, Part 1926) and the American Concrete Institute’s Guide to Formwork for Concrete (ACI 347) be strictly followed when considering safety factors and safe working loads. We especially advise that the minimum safety factors listed below be adhered to. When there are unusual job conditions, these minimum safety factors must be increased by the user.
Recommended Minimum Safety Factors Accessory Form Tie Form Anchor
Form Hangers Anchoring Inserts Used as Form Ties Brace Anchors Inserts Lifting Inserts Lifting Plates and Related Items
Safety Factor 2 to 1 2 to 1 3 to 1
Type of Construction All applications Formwork supporting form weight and concrete pressures only Formwork supporting weight of forms, concrete construction live loads and impact
2 to 1 2 to 1
All applications
2 to 1 3 to 1
Bracing of tilt-up precast concrete wall panels
2 to 1 4 to 1 5 to 1
Tilt-up construction Precast concrete construction
Precast concrete panels when used as formwork
Inserts used to make permanent connections between tilt-up or precast concrete elements
Hardware used for lifting and handling of tilt-up or precast concrete elements
Warning! When in doubt about the proper use or installation of Atlas Construction Supply’s accessories and hardware, contact Atlas Construction Supply for clarification. Failure to do so may result in exposure of workers to unsafe conditions or hazards, resulting in the possibility of injury or death to workers in the vicinity of the jobsite.
6
www.atlasform.com
SAFETY NOTES AND PRODUCT APPLICATION Liability Atlas Construction Supply guarantees its products as shipped from the plant and when used within the scope of this catalog. These products are, however, intended for use by trained, qualified and experienced workers. Even slight misuse or lack of supervision and inspection can contribute to serious accidents. All unusual applications should be carefully field tested before general production use. The user of Atlas products must evaluate the product application, determine the appropriate safe working load, and control all field conditions to prevent applications of loads in excess of the safe working load. Safety factors as shown are approximate. Safe working loads should never be exceeded. Availability Because of the technical skills required, certain products in this catalog are available only to those customers who have demonstrated the ability to apply and service these products properly. Worn Working Parts It is the user’s responsibility to continually inspect working hardware for wear and to discard the parts when wear is noted. DO NOT straighten bent bolts, rather discard and replace. Discard any bolts known to have been used at loads of 70% ultimate strength or more. Such bolts may have been stretched sufficiently to become brittlehard.
Impact wrenches must not be used to tighten bolts that are part of a form tie system, form anchor, or hanger system. Shop, Field Arc Welding DO NOT WELD TO ANY CASTING unless in the opinion of a qualified engineer such weld is in a no load non-critical area. Welding to iron castings can cause extreme brittleness to form near the weld area and can destroy nearly all of the casting’s load value. WIRE PRODUCTS are often tack welded for positioning. Since we cannot control either the workmanship or conditions under which this work is done, Atlas DOES NOT GUARANTEE any product altered in the field by welding or bending. Design Changes Atlas reserves the right to change product designs, safe working load ratings and product dimensions at any time without prior notice to users. (Such changes will be made only for product improvement or further safety.) Interchangeability Many of the products that Atlas Construction Supply manufactures and supplies are designed as a system. Atlas cannot guarantee that the components from systems supplied by other manufacturers are completely interchangeable with components supplied by Atlas.
WARRANTY Atlas Construction Supply will refund the price of or replace, at its election, any product which it finds to be defective provided the product has been used properly. EXCEPT AS EXPRESSLY STATED ABOVE, THE COMPANY MAKES NO WARRANTY OF MERCHANTABILITY AND NO WARRANTY OF FITNESS FOR ANY PARTICULAR PURPOSE NOR DOES IT MAKE ANY WARRANTY, EXPRESS OR, IMPLIED, OF ANY NATURE WHATSOEVER WITH RESPECT TO THE PRODUCT OR THE
USE THEREOF, BY WAY OF ILLUSTRATION AND NO LIMITATION, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR DELAY CAUSED BY DEFECTS, FOR LOSS OF USE, FOR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, OR FOR ANY CHARGES OR EXPENSES OF ANY NATURE INCURRED WITHOUT ITS WRITTEN CONSENT. THE FOREGOING IS THE FULL EXTENT OF THE RESPONSIBILITY OF THE COMPANY EVEN THOUGH THE COMPANY MAY HAVE BEEN NEGLIGENT.
www.atlasform.com
7
ALUMINUM SHORING FRAME HANDSET SHORING SYSTEM
30-ATLAS TECH PRODUCTS
AL-SPEED® Shoring Frame The innovative Atlas AL-SPEED® Frame is a strong, light and durable shoring frame that improves the quality and speed of concrete construction, eases formwork set-up and removal, and reduces construction costs. This premier aluminum frame is the result of rigorous research and testing; all performed to provide our customers with the very best shoring system available.
40-BAR SUPPORTS
High Load Capacity The high load capacity of the AL-SPEED® frame, combined with being lightweight (50 lbs) and requiring minimal components, provides contractors with a shoring frame that is safe, efficient and economical.
50-FLATWORK ACCESSORIES
Atlas Construction Supply takes pride in providing our customers with shoring solutions that will lead to accomplished project objectives and lasting relationships.
60-PRECAST & TILT-UP
Versatility The versatility of the AL-SPEED® Frame allows for quick erection and dismantling of simple and intricate deck layouts. The AL-SPEED® system also has fewer parts than other shoring systems, therefore maximizing productivity and minimizing jobsite losses/ thefts.
PRODUCTS
Frame Sizes (width x height) • 6’ x 6’, 6’ x 5’, 6’ x 2’8” • 3’ x 6’, 3’ x 5’, 3’ x 2’8”
Call Atlas for competitive pricing on HDO, MDO and PSF plywood. Atlas stocks various sizes and styles of plywood to suit different project requirements.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
AL-SPEED® SHORING FRAME
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
8
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
HANDSET ALUMINUM FRAME
® 20-FORMING ACCESSORIES
ADVANTAGES OF THE AL-SPEED® FRAME Aluminum: Lightweight and Durable. Will provide a long service life. High Shoring Coverage - up to 16 kip / leg. 32,000 lbs. support capacity per 50 lb. frame.
30-ATLAS TECH PRODUCTS
®
Versatile system can accommodate both simple or intricate deck designs. Less time and labor needed for erection and dismantling than other systems.
6’, 5’, & 2’ 8” high frames accommodate all shoring heights (4’6” Min.). Available in 6’ or 3’ widths. Only 2 revolutions per inch for AL-SPEED® jacks. Quick set-up and removal of system. Striated horizontal rails.
50-FLATWORK ACCESSORIES
AL-SPEED® FRAME COMPONENTS
®
40-BAR SUPPORTS
6’ wide frame reduces total number of frames needed to support suspended concrete and formwork. Approximately 100 Sq. Ft. per frame, up to 12” slab thickness. Minimal parts and components. Frame is complete with integral bearing surfaces.
10-FORMING & SHORING
AL-SPEED® SHORING FRAME
60-PRECAST & TILT-UP
Quicklock System allows for easy connection and removal of crossbraces.
PRODUCTS
80- TOOLS & PLACING
*One Semi-truck can carry up to 10,000 Ft2 of shoring equipment for up to 12” deck.
www.atlasform.com
70- FOUNDATION
®
9
Contractor Committed.
AL-SPEED® SHORING FRAME HANDSET ALUMINUM FRAME
Frame Capacity 3 Tiers High, Cross-Braced Towers Safety Factor= 2.5 : 1 Equal Screwjack Extension, Top & Bottom
BEAMS AND STRINGERS
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
LVL BEAMS
6.5” Aluminum Beams available in standard lengths: 7’0”, 9’0”, 10’6”, 12’0”, 14’0”, 16’0”, 18’0”, and 21’0”
Available in standard 4” x 4” with 7’ and 14’ lengths.
7.5” Stringers available in standard lengths 8’0”, 10’0”,12’0”, 14’0”, 16’0”, and 20’0”
Cross braces available in standard sizes: 4’ X 4’, 4’ X 6’, 4’ x 8’, 4’ x 10’
CROSSBRACES
PRODUCTS
6” x 2’8” Frame 6’ x 5’ Frame 6’ x 6’ Frame
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
FRAME SIZES
3’x 2’8” Frame
10
3’ x 5’ Frame
www.atlasform.com
3’ x 6’ Frame
Serving Concrete Customers Since 1980.
FORMING & SHORING
20-FORMING ACCESSORIES
TM
30-ATLAS TECH PRODUCTS
ATLAS A-DECK is a post, joist and drop-head handset shoring system designed to maximize labor productivity and reduce formwork cycle time. The primary components include hi-capacity post shores with drop heads, aluminum girders and LVL joists. The TM ATLAS A-DECK system provides a high level of productivity through the use of a 6’ x 8’ grid pattern, easy to handle components, and drop-heads for early retrieval and cycling of joists, girders and plywood. The ability to install the system from the ground with simple light-weight components results in added safety and overall ease of use.
40-BAR SUPPORTS
TM
50-FLATWORK ACCESSORIES
The A-DECK drophead provides contractors a safe and faster early-retrieval system than ‘rotary’ style stripping mechanisms. A single, unimpeded, square hammer blow can disengage the loaded wedge, dropping the girders and joists 4” for fast and easy removal. A fixed key prevents an unsecured wedge from prematurely disengaging. TM
For mid & high rises, A-DECK perimeter tables can be used for building perimeters which incorporate 3’ of workspace beyond the slab edge. The tables are available in a large combination of widths and depths.
60-PRECAST & TILT-UP
SMALLER PRONG USED PRIMARILY FOR GRID JOIST.
PRODUCTS
WEDGE AND TRAY DROP 4”.
www.atlasform.com
80- TOOLS & PLACING
DROP-HEAD BOLTS TO TOP OF POST SHORE.
70- FOUNDATION
LARGER PRONG USED PRIMARILY FOR ALUMINIUM GIRDERS.
STRIKE WEDGE WITH HAMMER TO ENGAGE AND DISENGAGE.
10-FORMING & SHORING
POST, JOIST & DROPHEAD HANDSET SHORING SYSTEM
ATLAS A-DECKTM
11
ATLAS A-DECKTM ADVANTAGES • Post shores can accommodate soffit heights from 6’-11” to 11’-7”, or up to 14’-5” with available extension.
30-ATLAS TECH PRODUCTS
• Can support a 12” thick concrete slab on 6’ x 8’ grid throughout entire post range, including use of extension. (Up to 15’-5” finished floor to finished floor). • Can support slabs up to 48” thick throughout post range with standard equipment.
40-BAR SUPPORTS
• Drop-head allows for early retrieval of joists and girders formwork and untrapped plywood while loaded post shore remains intact. • 6’ x 8’ grid pattern reduces the amount of post shores required, reduces installation time, and is well suited for the use of 4’ x 8’ plywood sheets.
50-FLATWORK ACCESSORIES
• Joists and girders are individually labeled by length to facilitate identification on the job site. • Fast cycling of equipment by means of fastactuating drop-head, racks, baskets and carts.
60-PRECAST & TILT-UP
• Hammer is only tool needed to install and strip system.
PRODUCTS
•Easily ties into A-DECKTM perimeter tables or AL-SPEED® shoring frame.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
ATLAS A-DECKTM
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
12
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
ATLAS A-DECKTM TECHNICAL FEATURES
10-FORMING & SHORING
ATLAS A-DECKTM
20-FORMING ACCESSORIES
• 4” drop distance facilitates removal of girders, joists, and plywood. • 3.5” X 3.5” LVL joists offer increased ability to place and secure plywood.
30-ATLAS TECH PRODUCTS
• Girders allow for use of conventional 4X4’S or 4X6’S when obstructions exist. • Allows for double camber conditions, up to 10% slopes in each direction.
40-BAR SUPPORTS
• Rigid braces provide better system stability than standard “jet-lock” style crossbraces. • Quick release post shore pin allows 1/8” drop to facilitate removal of post shore. • Drop head allows for changing direction of joist by 900.
50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
A-DECKTM Carts: Atlas offers customers the convenience of A-DECKTM Carts designed to hold girders, LVL joists, posts and drop-heads. Contractors can easily move material from one part of the job site to another and store material.
PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
13
Contractor Committed.
ATLAS A-DECKTM TABLES PERIMETER TABLES
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
ATLAS A-DECKTM perimeter tables can be used for building perimeters which incorporate 3’ of workspace beyond the slab edge. The tables are available in a large combination of widths and depths, including up to 24’ wide by 20’ deep, and provide safety railing that complies with OSHA regulations even after the slab has been cast. The tables are easily cycled up the building with the 4-cable adjustable A-DECKTM caddy, which is available in either single level or dual level sizes. In addition, the tables have hinging legs that can ‘fly over’ undisturbed fall protection on the level below.
14
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
10-FORMING & SHORING
DYNAMIC SHORING SYSTEM
20-FORMING ACCESSORIES
HIGH CAPACITY SHORING SYSTEM
30-ATLAS TECH PRODUCTS
The Dynamic shoring system was developed to decrease labor costs and increase productivity for high slab and high load capacity projects. Legs, frames and beams create a shoring system with minimal components that can support loads up to 25,000 lbs per leg.
40-BAR SUPPORTS
ICS Dynamic Shoring System has three leg sizes: 5’7”, 9’6” and 14’1” allowing contractors to achieve virtually any slab height. Versatility makes the Dynamic system the perfect choice for high slab and high capacity projects such as bridge supports, tunnel construction and power plants.
50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
15
Contractor Committed.
ATLAS TRUSS DECK TRUSS & JOIST TABLE FORMS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
30-ATLAS TECH PRODUCTS
Trusses In addition to handset decking systems, Atlas offers flying deck forms and truss solutions for repetitive, multi-reuse projects. Trusses are available in variable height aluminum or steel configurations. Joists are typically aluminum beams.
40-BAR SUPPORTS
Features of Atlas flying deck forms are: • Aluminum and steel trusses
50-FLATWORK ACCESSORIES
• Aluminum joists
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
• Table sizes up to 36’ wide and 85’ long
16
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
20-FORMING ACCESSORIES
COLUMN MOUNTED TABLE FORMS
10-FORMING & SHORING
ATLAS COLUMN MOUNTED DECK
30-ATLAS TECH PRODUCTS
Atlas offers column mounted deck systems that allow for fast cycling of repetitive deck layouts, without the need for typical reshore. The components include hi-capacity column mounted jacks, castellated primary members, and open web or aluminum joists. Features of Atlas Column Mounted Deck Systems:
40-BAR SUPPORTS
• Hi-capacity column mounted jacks with integral rollers. • Castellated beams with open web or aluminum joists.
50-FLATWORK ACCESSORIES
• Table sizes up to 30’ wide and 100’ long. • Minimal or no reshore necessary. • Fast pour cycles.
60-PRECAST & TILT-UP
For more information on the Atlas Column Mounted Jack see page 38.
PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
17
10-FORMING & SHORING
FORMING & SHORING
GARAGE BEAM SYSTEM-GBS
20-FORMING ACCESSORIES
GARAGE BEAM SYSTEM (GBS)
30-ATLAS TECH PRODUCTS
The Garage Beam System(GBS) is a comprehensive design and equipment plan for post-tensioned concrete beam and slab parking structures. The system consists of long beam form assemblies, high-capacity leg supports, column and capital forms, and reusable deck panels. All Garage Beam components are quickly handled and moved with forklifts and dollies for maximum forming productivity and reduced labor costs.
40-BAR SUPPORTS
Beam Forms The beam forms feature long assemblies faced with 3/16” steel skin plate for strength, durability and excellent concrete finish. No tie system or added beam bracing is required.
50-FLATWORK ACCESSORIES
Capital Forms All-steel capital forms are designed specifically for typical exterior or “pass-through” interior locations. Forms are steel-faced for smooth concrete finish and include steel chamfer. Provisions for post-tension cable penetrations are also included in the capital form design.
PRODUCTS
60-PRECAST & TILT-UP
Deck Panels Deck panels are field-fabricated with a template using wood or aluminum beams and HDO plywood allowing spans up to 22’-0” without center shoring. The HDO plywood deck panels produce a consistently smooth concrete finish and provide maximum reuse.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
18
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
20-FORMING ACCESSORIES
PARKING STRUCTURE FORM SYSTEM FOR NON-TYPICAL BEAM SIZE
10-FORMING & SHORING
AL-SPEED® GARAGE BEAM SYSTEM
30-ATLAS TECH PRODUCTS
Atlas offers approaches for beam and slab post-tensioned parking structures where equipment can be cycled in applications ranging from totally handset to totally pre-fabricated.
40-BAR SUPPORTS
Another feature of this system is that deck joists are typically designed to clear span in structural bays of up to 21’ in width. This not only eliminates the labor-intensive activity of center-bay post shoring, but also streamlines the reshoring requirement with regard to both equipment and labor costs.
50-FLATWORK ACCESSORIES
Fabricated beam lengths, handset or partial handset garage beam options are available. Please contact an Atlas representative to discuss specific project requirements.
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
19
Contractor Committed.
ATLAS ALUMINUM BEAM WALL FORMS GANGED ALUMINUM WALL FORMS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
Lightweight Atlas offers this wallform system weighing only 10 lbs./sq.ft. including 3/4” plywood skin, utilizing high strength aluminum members for both walers and strongbacks, and is offered for applications where rapid cycling and/or architectural surface finishes are required. The Atlas tie plate allows strongback channels to be set with a clear space of 3-1/2” between webs, allowing more lateral tie bolt adjustment than comparable systems.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
Atlas provides a complete system which includes tie equipment, alignment braces, catwalk brackets, lifting hardware, and miscellaneous accessories requiring the customer to provide only plywood and incidental timber for catwalks and bulkheads, etc.
20
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
GANGED ALUMINUM WALL FORMS
LIFTING LUG
10-FORMING & SHORING
WALLFORM COMPONENTS
20-FORMING ACCESSORIES
TIE PLATE
A-CLAMP
30-ATLAS TECH PRODUCTS
ALUMINUM BEAM (6-1/2”)
EDGE OF PLYWOOD
40-BAR SUPPORTS
ALUMINUM STRONGBACK (7-1/2”)
50-FLATWORK ACCESSORIES
PLAN VIEW
60-PRECAST & TILT-UP
A-CLAMP ASSEMBLY ANGLE BRACKET 3 HOLE BRACE PLATE
PRODUCTS
80- TOOLS & PLACING
CATWALK/SCAFFOLDING BRACKET
LIFTING LUG TIE PLATE
www.atlasform.com
70- FOUNDATION
BULK HEAD BRACKET
21
Contractor Committed.
ATLAS WALLBEAM FORMS GANGED LVL WALLBEAM FORMS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
30-ATLAS TECH PRODUCTS
In addition to its all aluminum wallform system, Atlas offers LVL Wall Beams as joists (and/or strongbacks). These form components are typically used with a tie pattern of 4ft. x 4ft. creating a symmetrical pattern with plywood yielding favorable concrete finishes.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
For more information on LVL wallbeam see page 40.
22
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
GANGED LVL WALLBEAM FORMS
LIFTING LUG
10-FORMING & SHORING
WALLFORM COMPONENTS
20-FORMING ACCESSORIES
YOKE BRACKET EDGE OF PLYWOOD
30-ATLAS TECH PRODUCTS
ALUMINUM STRONGBACK (7-1/2”) LVL WALLBEAM (5-1/2”) TIE PLATE
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
PLAN VIEW
60-PRECAST & TILT-UP
YOKE BRACKET
ANGLE BRACKET
PRODUCTS
80- TOOLS & PLACING
BULK HEAD BRACKET
CATWALK/SCAFFOLDING BRACKET TIE PLATE
www.atlasform.com
70- FOUNDATION
3 HOLE BRACE PLATE
LIFTING LUG 23
10-FORMING & SHORING
FORMING & SHORING
Contractor Committed.
ATLAS JUMP FORM SYSTEM
20-FORMING ACCESSORIES
JUMP FORM SYSTEM For external elevated form applications, Atlas offers an integrated jump form system to augment the gang forms.
30-ATLAS TECH PRODUCTS
The system utilizes the Atlas A100 Frame as its nucleus, which affords a 7’ wide working platform to service the elevated forms.
40-BAR SUPPORTS
The system, suspended from jump-shoes bolted to the previous concrete lift, allows stripping, reworking, and preparation of the forms to proceed prior to crane assistance. This is achieved by means of a retracting carriage on which the form is mounted. The carriage allows approximately 30” of retractions from the previously cast face, giving adequate working clearance “inside” the form.
An additional feature of the system is the trailing platform which is connected to the A100 Frame as the system climbs its way up the structure. This trailing platform serves several functions, namely:
PRODUCTS
• Allows convenient jump-shoe removal as construction proceeds. • Allows access to the safety tie-back. • Allows sacking and patching to be accommodated from this trailing platform.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
With all this activity being possible at the working level, the form never needs to be brought to ground level or stored elsewhere while decking activity is proceeding. With this system, it is no longer necessary for unacceptably lengthy crane-intensive hoisting operations to take place. Neither is it necessary for workers to “ride” the forms during re-setting, as the gang/platform unit is hoisted as one and landed into previously mounted jump shoes. Hoisting time is extremely brief.
24
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
JUMP FORM SYSTEM COMPONENTS
10-FORMING & SHORING
ATLAS JUMP FORM SYSTEM
20-FORMING ACCESSORIES 30-ATLAS TECH PRODUCTS
SCREWJACK
ROLL BACK CARRIAGE
JUMP SHOE
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
STRONGBACK CONNECTORS
PRODUCTS
A-100 BRACKET
WIND TIE
PLAN VIEW
www.atlasform.com
25
80- TOOLS & PLACING
TRAILING SCAFFOLDING
70- FOUNDATION
JUMP SHOE
PLATFORM BEAM
60-PRECAST & TILT-UP
ROLL BACK CARRIAGE
A-100 BRACKET
Contractor Committed.
ACS WALLFORM SYSTEM
The new ACS (Atlas Clamp System) heavy-duty modular ganged wallform offers an allowable 1,650 psf pour pressure, and weighs only 11 lbs per sq.ft. ACS provides Concrete Contractors with a high performance form that is easier to set-up, strip down and transport than other panel systems. • Maximum safe working pressure of 1,650 psf with a 7/8” (20mm) thru-rod or 1-1/4” to 1” taper tie. • Maximum safe working pressure of 1,250 psf with a 5/8” (15mm) thru-rod. • The side rails support an 18mm Dulen-X® board or 5/8” Birch Plywood. • Rail profile allows for easy clamping, long form life and is easier to repair than hollow frame panels. • Tie holes in large size panels are designed for high capacity ties. • The tie hole is in a conical shape for tie tolerances and for easier cleaning. • For bulkhead forming, spacer channels allow for wall thicknesses of 6” to 20” with adjustment increments of 1”.
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
20-FORMING ACCESSORIES
ATLAS GANGED WALLFORM CLAMP SYSTEM
30-ATLAS TECH PRODUCTS
10-FORMING & SHORING
FORMING & SHORING
10 ft
PRODUCTS
8’ x 10’ ACS Panel
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Available Panel & Filler Sizes
8 ft 26
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
ATLAS GANGED WALLFORM CLAMP SYSTEM
10-FORMING & SHORING
ACS WALLFORM SYSTEM
20-FORMING ACCESSORIES
Atlas ACS Wedge Clamp
30-ATLAS TECH PRODUCTS
The round wedge clamp provides an easy & fast method of connection between panels. The clamp works with any panel or filler size and allows for strong connections with minimal hardware. This one-piece clamp weighs only 3.5 lbs and has an admissible axial tension of 1,575 lbf. Typical Clamp Use: 10’ height - 4 clamps 8’ Height - 3 clamps 4’ Height - 2 clamps
40-BAR SUPPORTS
ACS Accessories
ACS Crane Clamp
ACS Spacer Channel
50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
The ACS spacer channel allows for an adjustment to wall thickness from 6” to 20” in increments of 1”. ACS Brace System
PRODUCTS
THERMOPLASTIC COATING ALUMINUM
80- TOOLS & PLACING
• High Use Capability • 18mm Poly-Propylene Composite Panels • Durability - Constant rigidity throughout lifetime • No swelling, shrinking or delamination • Workable like wood- nailing, sawing • Same attachment to panel frame as plywood • Repairability • Less form release agent required • Easy to clean forms • Produces a dense & smooth concrete surface
70- FOUNDATION
Atlas ACS Features Dulen-X® Board
FOAMED THERMOPLASTIC CORE
www.atlasform.com
27
MODULAR WALLFORM STRAIGHT & RADIUS
30-ATLAS TECH PRODUCTS
This metric dimension, straight and radius modular forming system consists of a galvanized steel frame and a specially coated 15mm (5/8”) plywood face. It provides the strength, durability, versatility and concrete finish needed for most gangforming applications.
40-BAR SUPPORTS
Panels and fillers Available in a variety of widths from 25cm to 200cm, and heights of 1 meter or 3 meters, this range of panel and filler sizes means you’ll be able to form almost any wall dimension. When combined with corners and accessories, pilaster, bulkheads and columns can be formed with standard equipment.
50-FLATWORK ACCESSORIES
Horizontal or vertical Alisply forms can be used horizontally or vertically, even within the same gang without compromising strength. Alisply has the strength required for the large contact areas and fast pour rates common in large gangform applications. With a design pressure of 1230 lbs/sq.ft., only two ties are needed for 3 meter panel heights.
PRODUCTS
60-PRECAST & TILT-UP
Simple connections The Alisply system features simple clamp connections that eliminate the need for tools and aligning bars. Setting up or changing the configuration of gangs is fast and simple with these innovative attachment clamps, reducing assembly confusion, increasing productivity and simplifying the gangforming operations. Alisply Circular Alisply Circular is a recoverable modular formwork system for circular fair-faced concrete walls, designed to be handled with a crane. Alisply Circular consists of a light galvanized steel frame and a 15 mm thick phenolic plywood lining. The frame incorporates tie rods that allow giving the wall the required radius on site.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
ALISPLY
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
28
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
20-FORMING ACCESSORIES
ATLAS GANGED RADIUS WALL FORM SYSTEM
30-ATLAS TECH PRODUCTS
The Atlas Adjustable Waler System is capable of servicing both segmental and full circular construction of round tanks. For full circular construction, the system can be utilized tieless, the walers being capable of withstanding lateral concrete pressures in the form of tension/ compression rings.
40-BAR SUPPORTS
The system comprises a ply-faced form, with aluminum beam vertical members, which are in turn supported by horizontally oriented adjustable waler units which create a true curve. This system allows pipe penetrations with a minimum of inconvenience. Radius adjustments of 10’ and up can be accommodated.
50-FLATWORK ACCESSORIES
FLEX-FORM SYSTEM
60-PRECAST & TILT-UP
The all-steel Flex-Form system has integral 4” deep vertical stiffeners with 3/16” steel skin plate to provide a 1,000 psf system that handles radius 5’ and over.
PRODUCTS
80- TOOLS & PLACING
Panels are delivered to the job site preassembled to meet specific job requirements. Flex-Form panels are available in over 100 sizes, from 2’ wide by 1’ long to 10’ wide by 20’ long and are available on a sale or rental basis.
70- FOUNDATION
Pre-rolled steel ribs set the radius. Factory rolled top and bottom ribs bolt to flexible panels to shape and securely hold the form in the radius required. Panels conform accurately to the radius of the ribs ensuring that the correct radius is achieved every time.
www.atlasform.com
10-FORMING & SHORING
RADIUS WALL FORMS
29
ONE-SIDED WALL FORMS Tied and Ganged One-sided Forms Atlas provides wall form equipment as described in the Ganged Wall Form Section along with weld brackets which are mounted to the soldier beams supporting shoring to the basement excavation typically at 8 ft. centers. Concrete placement rates at 5’/hr. can generally be accommodated, while still maintaining 5 ft. vertical spacing of ties. Standard inventory, snub-nosed coil taper ties are included as part of the system package, allowing both rapid installation and stripping of forms.
30-ATLAS TECH PRODUCTS 50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
Tied and Handset One-sided Forms Atlas has a unique handset (craneless) approach to the forming of one-sided (blind) walls. The same components as above are utilized by individually placing aluminum beams. This design allows quick setting and stripping practices, along with the high load capacity of aluminum, absent of the use of a crane. This system is ideal for single lifts and projects with limited equipment and space.
PRODUCTS
60-PRECAST & TILT-UP
Tie-Less Ganged One-sided Forms Atlas is able to offer a basic gang wall system, this time tieless through the concrete wall and connected to, and laterally supported by, the Atlas A-100 Frame secured to the floor or foundation below.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
ONE-SIDED WALL FORMS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
30
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING & SHORING
HANDSET WALLFORMS
10-FORMING & SHORING
STEEL-PLY
20-FORMING ACCESSORIES 30-ATLAS TECH PRODUCTS
The Steel-Ply forming system is a pre-engineered, factory built, reusable concrete forming system. It may be used in handset or gang form applications, for commercial or residential structures. The Steel-Ply forming system can form walls of almost any shape or size, with accessories for special structures and details. The Steel-Ply forming system saves time because it is easy to set up and strip. No measuring, sawing, drilling, or nailing is required. The only tool required is a hammer.
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
Steel-Ply is available in a variety of standard sizes which can be combined to form virtually any dimension. This forming system is constructed of laminated plywood mounted on steel frames. With proper care this system can be used up to 200 times before being reconditioned. All standard panel sizes and most accessories are available on a rental or sale basis.
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
31
Contractor Committed.
ATLAS COLUMN FORMS ATLAS AL-SPEED® COLUMN FORMS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING & SHORING
30-ATLAS TECH PRODUCTS
Atlas AL-SPEED® fully fabricated adjustable aluminum column form system offers the advantages of providing an efficient column form solution while producing an architectural concrete finish. Fully fabricated forms are generally provided on a rental basis or job duration lease.
40-BAR SUPPORTS
Atlas AL-SPEED® column forms are capable of 36” widths and generally utilized to a height up to 16 ft. They are provided with quick double closures (two piece) or hinged/ single closures (one piece). Form skins are generally 3/4” HDO.
50-FLATWORK ACCESSORIES
The AL-SPEED® column clamps are available as individual rental or sale items. AL-SPEED® fits columns from 14” x 14” up to 36” x 36”.
AL-SPEED® COLUMN FORM
PRODUCTS
Atlas Multi-Channel fully fabricated aluminum adjustable steel column form system offers the advantages of providing an efficient column form solution while producing an architectural concrete finish. Fully fabricated forms are generally provided on a rental basis or job duration lease.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
ATLAS MULTI-CHANNEL COLUMN FORMS
MULTI-CHANNEL COLUMN FORM
32
Atlas Multi-Channel forms are capable of 72” widths and have been used to heights of 45 ft. They are provided with quick swivel barrel assembly double closures. Atlas can offer these pre-assembled and delivered to the jobsite ready to use. The Multi-Channel column clamps are also available as individual rental or sales items. Multi-Channel Clamp fits columns from 12” to 72”.
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
10-FORMING & SHORING
COLUMN FORMING ONE PIECE ROUND COLUMN FORMS
20-FORMING ACCESSORIES
One-piece round column forms are economical, and produce a smooth concrete finish. Manufactured of fiberglass reinforced plastic, these forms will not dent, sag, rot or weather and require little or any maintenance. Round Column Forms are lightweight, easy to handle, and simple to set up and remove. RCF forms have only one vertical seam and are supplied complete with bracing collars and “fast” bolts. Round Column Forms are designed for repeat use. RCFs are available on a sale or rental basis with diameters from 12 to 48 inches; available in one-piece lengths up to 20 feet.
30-ATLAS TECH PRODUCTS
STEEL ROUND COLUMN FORMS
40-BAR SUPPORTS
Heavy Duty Steel Column forms develop an exceptionally smooth, hard surface free of voids and with a minimum number of indistinct seams. All forms are galvanized constant radius steel half round sections and quarter round sections (for forms over 48” in diameter) bolted into units for crane handling on the job site. Each component is framed with flange angles diecut and punched for accurate flush butt joints without protrusion on the contact surface. Vertical and horizontal seams, opened and closed with each pour, are connected with high speed bolts to speed setting and stripping. All standard column diameters from 12” to 84” in 8’0, 4’0, and 1’0 lengths are available on a sale or rental basis.
50-FLATWORK ACCESSORIES
ATLAS LINED TUBE Provides architectural concrete for all round columns. Gives a glassy smooth concrete finish. Can be left in place for full curing and protection until the job is finished. Eliminates the need for water and sand blasting in most cases. Forms up to 24” diameter will have one vertical seam; over 24” will have 2 seams.
60-PRECAST & TILT-UP
• • • • •
PRODUCTS
80- TOOLS & PLACING
Atlas Lined Tube combines the ease of handling, strength, and economics of one-piece paper tube column forms, with a poly liner that gives a smooth finish to the concrete, a finish that is sure to please the architect and owner. Atlas Lined Tubes are made to order and can be delivered within 5 working days. Sizes are from 6 to 48 inches in diameter, and in almost any lengths.
www.atlasform.com
70- FOUNDATION
Atlas Lined Tube is designed to hold full hydrostatic pressure of concrete in a single pour. Forms can be stripped any time after two days, or left on to protect columns from spills and other hazards of construction until the job is finished.
33
Contractor Committed.
COLUMN FORMING SONOTUBE FORMS Sonotube forms are made from multiple layers of high quality fibre, providing a strong, lightweight and easy to handle column form. The spiral wound and laminated Sonotube form is a one-piece unit; there are no assembly costs and the form may be cut to fit any desired length.
Inside Diameter
USES • Round columns • Piers and footings • Pile forms • Light pole and fence pole bases • Flagstones and round steps
Standard Wall Thickness
Product Code No. Heavy Weight
0.120
Heavy Wall Thickness 0.145
6”
15.10.10106
0.120
15.10.20106
0.160
8”
15.10.10108
0.120
15.10.20108
0.160
10”
15.10.10110
0.140
15.10.20110
0.190
12”
15.10.10112
0.140
15.10.20112
0.190
14”
15.10.10114
0.165
15.10.20114
0.215
16”
15.10.10116
0.165
15.10.20116
0.250
18”
15.10.10118
0.190
15.10.20118
0.250
20”
15.10.10120
0.190
15.10.20120
0.295
22”
15.10.10122
0.210
15.10.20122
0.295
24”
15.10.10124
0.210
15.10.20124
0.295
26”
0.270
28”
0.295
15.10.20128
0.365
0.295
15.10.20130
0.365
30’
15.10.10130
32”
36”
0.295
0.295
34”
0.365
0.295 15.10.10136
0.295
0.365 15.10.20136
0.365
42”
15.10.20142
0.445
48”
15.10.20148
0.505
60”
15.10.20160
0.600
PRODUCTS
SONOTUBE FINISH FREE FIBRE FORMS Sonoco Finish Free fibre form is lined with Duraglas coating that provides for a smooth concrete finish when forms are stripped. Duraglas will leave no spiral marks, seams or imperfections that would impact the finished surface of the concrete. Available in lengths up to 12 feet and interior diameters from 12 to 36 inches. Forms can be cut to length and drilled at the job site to meet specific project requirements.
80- TOOLS & PLACING
70- FOUNDATION
Standard Product Code No.
4”
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
34
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
SCISSOR CLAMPS
10-FORMING & SHORING
COLUMN CLAMPS
20-FORMING ACCESSORIES
• Quickly and easily applied or removed with no tools other than a carpenter’s hammer. Driving home permanently attached wedge pulls clamp tight. • Bars are made of high strength carbon steel. Brackets are rugged malleable iron.
30-ATLAS TECH PRODUCTS
• Clean-Cut punched slots that provide tolerance adjustment. • No detachable parts: a rivet prevents the bracket from slipping off. Wedges are chained to the brackets.
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP PRODUCTS
80- TOOLS & PLACING
* Clamps are sold and rented by the piece, but two (2) pieces are required to make a useable clamp set. ** Concrete dimensions based on 3/4” plywood with flat 2 x 4’s at 6” on center.
www.atlasform.com
70- FOUNDATION
1) 3/4” plywood with flat 2 x 4s on 6” centers. 2) Ten foot rate of pour. 3) Pure liquid head of 150 lbs. per square foot of accumulated depth. 4) Plywood deflection between clamps limited to L/360 or 1/16”. 5) Column Clamp safety factor = 2
35
Contractor Committed.
The Atlas Post Shore is engineered for strength, installation efficiency and long service life. This quality shoring product features high load capacities for shoring heights from 6’6” to 11’1” (8,100 lbs. fully closed to 5,100 lbs. at max extension*).
Safe Working Load (kips)
ATLAS POST SHORES
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
10
8.1
8.1
8 6
5.1
4 2 0 6' 6"
7' 2"
7' 10"
8' 6"
9' 2"
9' 10"
10' 6"
11' 1"
Height
30-ATLAS TECH PRODUCTS
Atlas Post Shore Load Capacities (3:1 safety factor)
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
• High Load Capacities at Shoring Heights From 6’5” To 11’1” 15,000 lbs. fully closed to 13,700 lbs. at max. extension *(3 To 1 Safety Factor) • Extremely High Strength To Weight Ratio (35 lb. Post Shore, 59 lb. Jumbo Post Shore) • Minimal Time And Labor Needed for Set-Up And Removal • Quick Disconnect/Breakdown System • Galvanized For Durability & Long Service Life • Easy Height Adjustment • Rolled Thread • No Loose Parts • Weatherproof • Head And Base Plates Drilled For Nailing Atlas Post Shore
Product Code No. 10.21.02402
Atlas Jumbo Shore
Product Code No. 10.21.02412
350 & 550 POST SHORES Heavy Duty Post Shores are available in three models providing adjustable shoring heights from 5’7” to 18’4”. These Post Shores each carry load ratings up to 10,000 lbs. (3 to 1 safety factor). With this higher load rating, Post Shores can often be spaced further apart, producing equipment and labor savings for the contractor.
PRODUCTS
60-PRECAST & TILT-UP
The Atlas Jumbo Shore is fabricated with a secure locking pin that is inserted into one of the holes spaced at 4” intervals along the inner post. Once Jumbo Shore is set in position, a threaded collar with handle allows for easy height adjustment over a 6” range. With a high load capacity, the 59 lb. Jumbo Shore may be spaced further apart than other post shore systems, therefore reducing material and labor costs. The Atlas Shores are quickly and safely set in place with 3 simple steps: 1. Lift inner tube to approximate height required. 2. Insert pin in nearest hole to desired height. 3. Turn handle of threaded collar for final adjustment.
Post Shores are quickly and safely set in place. They have a unique locking pin for approximate height adjustment. This pin is inserted into one of the holes spaced at 4” intervals along the length of the post. After the Post Shore is positioned, a threaded collar with a handle permits fine height adjustments over a 6” range.
80- TOOLS & PLACING
70- FOUNDATION
The Atlas Jumbo Shore is engineered for maximum strength, installation efficiency and long service life. This quality shoring product features high load capacities for shoring heights from 6’5” to 9’10” (15,000 lbs. fully closed to 13,700 lbs. at max extension*).
36
350 Post Shore
Product Code No. 12.50.45017
550 Post Shore
Product Code No. 12.59.45018
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
ATLAS AL-SPEED® SAFETY RAIL POST
TOP ADJUSTING WING NUT
20-FORMING ACCESSORIES
2 x 4, 2 x 6 OR CABLE READY
30-ATLAS TECH PRODUCTS
The Atlas AL-SPEED® Safety Rail Post opens wide and tightens quickly, allowing for easy application to practically any project. The post is easily installed, utilizing a top adjusting wing nut which creates an ability to tighten from a standing position. A newly designed base adds to the simplicity of setup with predrilled holes providing trouble-free fastening to decks. The post can also adjust to any slab size between 0”-29”, with the adjustable clamp extending to the full 29”, preventing the bottom piece from falling out. A redesigned top with drop pin makes the AL-SPEED® Safety Rail Post simple and efficient to use. The AL-SPEED® Safety Rail Post is also galvanized for durability and designed to withstand the toughest jobsite conditions.
40-BAR SUPPORTS
TOEBOARD READY
AL-SPEED Safety Rail Post Advantages ®
CAPTIVE INNER MEMBER EXTENDS TO 29”
50-FLATWORK ACCESSORIES
• Galvanized for maximum durability and service life. • Easily adjustable clamp secures to slab sizes between 0”-29”. • Predrilled holes at base provide for easy screwing to concrete slabs. • Top adjusting wing nut allows for tightening from a standing position. • Easy to maintain and transport from job to job.
10-FORMING & SHORING
SAFETY RAIL POST
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
Atlas AL-SPEED® Safety Rail Post Extension attaches to the Atlas AL-SPEED® Safety Rail Post and allows contractors to meet OSHA requirements of a 42” tall safety barrier after concrete is poured when standing on top of the finished concrete slab.
AL-SPEED Safety Guard Rail Post
80- TOOLS & PLACING
Product Code No. 20.10.10100 AL-SPEED Safety Guard Rail Post Extension Product Code No. 20.10.10110
www.atlasform.com
37
COLUMN MOUNTED JACK The Column Mounted Jack offers a 60 kip capacity adjusting element. The jack supports column mounted tables and is an integral part of the column hung deck system. Ideal uses include supporting steel “I” beams and flying tables. 40k Column Mounted Jack Product Code No.
10.30.30400
60k Column Mounted Jack Product Code No.
10.30.30600
ATLAS RESHORE JACK Both light and heavy duty jacks offer a high capacity adjusting element to be utilized in conjunction with either 6” x 6” or 8” x 8” wood members (not included). Ideal uses include reshoring of structural steel “I” beams or reshoring concrete slabs supporting flying shoring tables. Product Code Standard
12.51.46681
Product Code Heavy Duty
12.51.46941
ATLAS WALER JACK Product Code Standard
20.20.21000
Product Code Deluxe
20.20.21100
PRODUCTS
ATLAS BRIDGE OVERHANG BRACKET AVAILABLE IN 30” AND 42”
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
Contractor Committed.
FORMING COMPONENTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
38
www.atlasform.com
Product Code 28”
20.10.21028
Product Code 42”
20.10.21042
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
Product Code No.
Wt. Lbs.
20.10.21554
45.0 Ea.
C-49
BRIDGE OVERHANG BRACKET
20-FORMING ACCESSORIES
Designed for use on prestressed concrete beams and medium depth steel beams. Aids in preventing web of beam from bending during construction of bridge deck. Design allows Bracket to be used on prestressed concrete beams without requiring wood blocking. Accepts C-51 Wall Plate Assembly † Under special conditions, Bracket can be adjusted to a minimum vertical height of 14”.
C-49-D 30-ATLAS TECH PRODUCTS
Special Order Product Code No.
Wt. Lbs. 50.0 Ea.
Designed for use on deep steel plate girder beams. Aids in preventing web of beam from bending during construction of bridge deck. Accepts C-51 Wall Plate Assembly Note: C-49-D is shipped unassembled
C-49-JR
Special Order Product Code No.
40-BAR SUPPORTS
BRIDGE OVERHANG BRACKET
10-FORMING & SHORING
BRIDGE OVERHANG BRACKET
Wt. Lbs. 35.0 Ea.
50-FLATWORK ACCESSORIES
Designed for use on prestressed concrete beams and medium depth steel beams. Short chord length allows brackets to be used where full sized brackets can not be utilized. Design allows Bracket to be used on prestressed concrete beams without requiring wood blocking. Accepts C-51 Wall Plate Assembly
C-51
FOR ADJUSTABLE BRIDGE OVERHANG BRACKET FOR USE WITH 3/4” DIAMETER BOLT
Special Order Type
Product Code No.
Wt. Lbs.
.40 Ea.
Wall Bracket Only
1.35 Ea.
ADJUSTABLE INSERT ADAPTER
C-51-R
FOR ADJUSTABLE BRIDGE OVERHANG BRACKET
PRODUCTS
1.75 Ea.
70- FOUNDATION
Assembly Adjustment Plate Only
60-PRECAST & TILT-UP
WALL PLATE ASSEMBLY
Special Order 80- TOOLS & PLACING
Product Code No.
Wt. Lbs. 1.75 Ea.
www.atlasform.com
39
Atlas Laminated Veneer Lumber (LVL) beam is an engineered wood fiber that promotes innovative designs, efficiencies and cost savings when used in our Atlas wall forms, deck forms, beam forms, column forms and other concrete forming applications. Atlas LVL beam is a durable and reusable forming element that is manufactured to resist bowing, shrinking and twisting; results in uniform, predictable and true line performance.
30-ATLAS TECH PRODUCTS 40-BAR SUPPORTS
Atlas designs and engineers the LVL Beam in-house to accomodate multiple forming applications. This achieved flexibility provides easy form construction and saves considerable time. The strength and stiffness provided in the LVL Beam minimize the amount of labor needed for constructing and utilizing the forms.
FORMING PLYWOOD HDO CONCRETE FORM PANEL HDO 100/30 is designed to provide multiple reuses and produce excellent concrete finishes at a lower per pour cost than other HDO forming panels. HDO 100/30 concrete form panels are made of high quality, exterior grade plywood with an high resin content face overlay for extra durability and smoothness.
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
Contractor Committed.
ENGINEERED LUMBER
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
PRODUCTS
PSF (Phenolic Surface Film) plywood offers concrete contractors significant advantages over other types of forming panels: • Superior concrete finish: smooth, hard, clean and consistent. • High durability for maximum # of reuses. • Excellent strength and stiffness. • Higher labor efficiency. • Phenolic overlay pour surface on both sides of panel. • Edge sealed. • Attractive contact foot material costing.
80- TOOLS & PLACING
70- FOUNDATION
PSF CONCRETE FORM PANEL
40
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
Product Code No. 20.27.10050
5/8” Pine
20.27.10060
3/4” Pine
20.27.10075
1” Pine
20.27.10100
1-1/16” Pine
20.27.10107
1-1/2” Pine
20.27.10150
20-FORMING ACCESSORIES
Length 1/2” Pine
10-FORMING & SHORING
WOOD CHAMFER
CHAMFER/FORMER STRIPS
30-ATLAS TECH PRODUCTS
RADIUS FORMERS Made from a specially designed plastic material that provides a smooth, uninterrupted, rounded radius corner to poured concrete. The material strips cleanly from finished concrete and is easily removed from forms for reuse.
Product Code No. 20.27.22100
3/4” Plastic Radius with Tail
20.27.22075
40-BAR SUPPORTS
Length 1/2” Plastic Radius with Tail
50-FLATWORK ACCESSORIES
CHAMFER STRIPS
Length
Product Code No.
1/2” All Plastic
20.27.20050
5/8” All Plastic
20.27.20060
3/4” All Plastic
20.27.20075
20.27.20107
PRODUCTS
20.27.20100
1-1/16” All Plastic
DRIP STRIPS
www.atlasform.com
80- TOOLS & PLACING
Provides a smooth uniform drip groove on the underside of roof overhangs and porches. The material is nailed to the form and is easily removed from the concrete. It also can be reused several times.
70- FOUNDATION
1” All Plastic
60-PRECAST & TILT-UP
Provides a smooth, uninterrupted beveled edge to piers, beams, and all outside corners of poured concrete. They are easily applied, equipped with or without nailing flange to facilitate installation, and reusable for maximum economy.
41
Atlas offers the widest selection of architectural concrete formliners in the industry. Over 500 patterns and textures allow for design versatility; with custom sizes and patterns also available for specific job requirements. Contact your Atlas representative for information on patterns & sizes. A complete catalog is available with detailed information on each formliner.
30-ATLAS TECH PRODUCTS
Formliners are available in the following different materials depending on the specific application and the number of reuses required.
40-BAR SUPPORTS
SPS Plastic - A single use plastic form liner designed for limited application. Made from a polystyrene plastic, the initial square foot price is much less than other types of formliner material. This proves very economical when only one use is needed.
50-FLATWORK ACCESSORIES
ABS Plastic - Thermoformed in ABS plastic, these formliners exhibit good impact resistance and excellent overall performance. Reuse factor is 10, subject to pattern configuration, proper handling and jobsite conditions. Dura-Tex - An economical polyurethane elastomer formliner that possesses many of the qualities of premium elastomeric, but with slightly less durability. Pattern reproduction is excellent and the reuse factor is 40, subject to pattern configuration, proper handling and jobsite conditions.
PRODUCTS
60-PRECAST & TILT-UP
Elasto-Tex - A premium polyurethane elastomer formliner that exhibits exceptional durability and tear strength. It is flexible enough to allow stripping from slight undercuts or complex designs and resilient enough to maintain pattern details. Reuse factor is 100, subject to pattern configuration, proper handling and jobsite conditions. Packaging Formliners are generally available in standard 4’ x 10’ sheets. Custom sizes and patterns are available upon request.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
FORMLINERS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
42
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
10-FORMING & SHORING
FORMLINERS Formliner Patterns
20-FORMING ACCESSORIES
Hundreds of different sizes, shapes & textures are available in the following typical patterns:
30-ATLAS TECH PRODUCTS
• Fractured (Fin, Rib, Flute) • Wood • Brick • Block • Stone • Smooth Flute • Custom patterns also available!
Features of Formliners
40-BAR SUPPORTS
• Nearly all patterns are available in 4 types of materials, ranging from single-use to 100 uses! • Hundreds of typical patterns to choose from. • Custom patterns also available. • Typical patterns provided in 4’ x 10’ sheets. • Consistent results. • Easy installation. • Easy to strip when Atlas Release or Bio-Guard is used as the form release agent. • Knowledgeable technical support.
50-FLATWORK ACCESSORIES
Formliner Accessories
60-PRECAST & TILT-UP
Form Release Agent - Atlas Release is an ideal form release agent for any of the Dayton Superior formliners. Atlas Bio-Guard water-based release agent has also produced excellent results on polyurethane formliners.
PRODUCTS
70- FOUNDATION
Rustication & Chamfer Strips - Create distinct features and bold reveals with easy to attach rustication & chamfer strips. These reusable strips provide sharp features to enhance the appearance of exposed concrete. Just nail to the form; also prevents leakage.
80- TOOLS & PLACING
www.atlasform.com
43
10-FORMING & SHORING
FORMING ACCESSORIES
Contractor Committed.
MIKE BRACKET
FORMING COMPONENTS 3/4” Plywood
20-FORMING ACCESSORIES
Aluminum Beam Snubnose Taper Tie Atlas Tie Plate
30-ATLAS TECH PRODUCTS
Aluminum Strongback
Standard Mike Bracket
20.20.63000
Heavy Duty Mike Bracket
20.20.62000
3/4” Rib Height
#5 Rebar
3/4” Plywood
PRODUCTS
End Dimension Keeper STAY-FORM
STAY-FORM or Quickjet are ribbed expanded metal leave-in-place concrete forms that are used for forming bulkheads, pile caps, grade beams, blindside walls, bridge applications and wherever form removal is difficult. Construction joints are easily made; each side of STAY-FORM or Quickjet provides a substantial key for bonding abutting pour faces. STAY-FORM or Quickjet may also be used for curved forming applications, such as water treatment tanks. • Reduces labor costs in difficult forming applications. • Joint scabbling is eliminated. • Allows for continuous placement of rebar. • May be cut to size to fit specific project requirements. • Allows for visual inspection of concrete pour. • Pre-galvanized for jobsite storage. Blind side walls are easily formed using STAY-FORM or Quickjet with a special HookTie and conventional formwork on face side.
Lumber Dimension
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Expanded mesh between solid ribs
Lumber & Wedge
Safe Working Loads (2.0 to 1) 1” Standard Mike Bracket - 18,000 lbs. 1-1/4” Heavy Duty Mike Bracket - 36,000 lbs.
STAY-FORM/QUICKJET
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
T EE ET SH HE D S T ” S TD 79 7” S t 9 je ick orm Qu tayf S
Once welded to the existing soldier beams, the Mike Bracket allows contractor time and labor saving versatility of employing a standard heavy-duty gang wall form system for a onesided wall form. A coil nut is attached to the Mike Bracket in a manner that permits off-center entry with our snubnose taper tie. The Mike Bracket is produced of A-36 hot rolled steel. The Mike Bracket is to be adequately welded to the soldier beam with 3/8” fillet weld, fully on each 3” side.
Wall Thickness + 7/8”
Hook Tie Keeper
44
Brand
Product
Product Code No.
Stayform
27” x 97” panel
20.75.12797
Quickjet
19.7” x 78.7” panel
20.75.21500
Quickjet
23.6” x 78.7” panel
20.75.21600
Quickjet
Quickjet Angle
20.75.22200
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
20-FORMING ACCESSORIES
DSI HIGH STRENGTH FORM TIE ASSEMBLIES
Size
Length
Safe Working Load
Product Code No.
DSI Rod
5/8”
48”
19.6 Kips
10.63.16048
DSI Rod
5/8”
66”
19.6 Kips
10.63.16066
DSI Rod
5/8”
72”
19.6 Kips
10.63.16072
DSI Rod
7/8”
48”
33.7 Kips
10.63.14048
DSI Rod
7/8”
66”
33.7 Kips
10.63.14066
DSI Rod
7/8”
72”
33,7 Kips
10.63.14072
Component
Taper
Length
Safe Working Load
Product Code No.
DSI 7/8” Taper Tie
1”-1-1/4”
62”
38,200 Lbs.
10.63.12062
DSI 7/8” Taper Tie
1”-1-1/4”
72”
38,200 Lbs.
10.63.12072
Component
Size
Product Code No.
Component
Size
DSI She Bolt
5/8”
10.63.16700
DSI Wing Nut
5/8”
10.63.16910
DSI She Bolt
7/8”
10.63.14700
DSI Wing Nut Bracket / Cathead
5/8”
10.63.16920
DSI Wing Nut
7/8”
10.63.14910
DSI Wing Nut Bracket / Cathead
7/8”
10.63.14920
1” PVC Sleeve 1-1/4” PVC Sleeve
Product Code No.
Sleeve I.D.
Product Code No.
5/8”
1”
13/16”
50.41.07501
Component
Size
Product Code No.
7/8”
1-5/16”
1”
50.41.10001
Plate Washer
3” x 3”
20.31.83003
1”
1-11/16”
1-3/8”
50.41.12501 Component
Size
Product Code No.
DSI Coupler
7/8”
10.63.14930
Component
Length
Dia.
Product Code No.
5/8” Plastic Cone
1-1/2”
1-5/8”
20.35.50006
7/8” Plastic Cone
1-1/2”
1-7/8”
20.35.50004
1” Plastic Cone
1-1/2”
2-1/4”
20.35.50003
Cone Removal Tool
60-PRECAST & TILT-UP
Sleeve O.D.
50-FLATWORK ACCESSORIES
3/4” PVC Sleeve
40-BAR SUPPORTS
Bar Size
30-ATLAS TECH PRODUCTS
Component
Component
20.35.70010 Wt. Lbs.
Product Code No.
5/8”
.26 ea
20.28.45010
7/8” Lead Plug
7/8”
.37 ea
20.28.45020
1” Lead Plug
1”
.52 ea
20.28.45040
PRODUCTS
Size
COIL FORM TIE ASSEMBLIES ARE ALSO AVAILABLE Item Code D-9
Catalog Page # 68
Coil Rod
B-12
59
Coil Wing Nut
B-39
65
Coil She Bolt
D-30
72
45
80- TOOLS & PLACING
www.atlasform.com
Component Coil Taper Tie
70- FOUNDATION
Component 5/8” Lead Plug
10-FORMING & SHORING
ATLAS FORM TIE ASSEMBLIES
Hex Head. Sold Only in Box of 100. Standard Breakback is 13/16” End
End
Wall Breakback
Wall Size
8-1/4” L & W Only Product Code No. A-4-H
5”
20.21.31105
6”
20.21.31106
31.8
23.5
7”
20.21.31107
32.9
1” x 1” Plastic Cone
Wall Size
6”
30-ATLAS TECH PRODUCTS 40-BAR SUPPORTS
20.21.32106
Wt. Lbs. per 100
7”
20.21.32107
24.7
7-5/8”
20.21.33107
33.6
20.21.34107
25.4
8”
20.21.31108
34.0
25.8
9”
20.21.31109
35.1
26.9
10”
20.21.31110
36.3
20.21.32108
9”
20.21.32109
10”
20.21.32110
28.0
11-5/8”
20.21.33111
38.1
11-5/8”
20.21.34111
29.9
12”
20.21.31112
38.5
20.21.31113
12”
20.21.32112
30.3
13”
14”
20.21.32114
32.6
14”
20.21.31114
40.8
15”
20.21.32115
33.7
15”
20.21.31115
41.9
34.8
16”
20.21.31116
43.0
20.21.31118
45.3
16”
50-FLATWORK ACCESSORIES
4-3/4” L & W Only Product Code No. A-4-H
20.21.32116
18”
20.21.32118
37.1
18”
20”
20.21.32120
39.4
20”
20.21.31120
47.6
22”
20.21.32122
24”
20.21.31124
52.1
23”
20.21.32123
26”
20.21.31126
24”
20.21.32124
28”
20.21.31128
28”
20.21.32128
30”
20.21.31130
30”
20.21.32130
36”
20.21.31136
36”
20.21.32136
48”
20.21.31148
43.9
50.6
58.9
Made with 1” x 1” plastic cones or metal spreader. Other sizes available upon request. Hex head measures 1/2” across flats. Note: Because of high tension stress, 100% breakback is not guaranteed for hex head snap ties with L & W over 4-3/4”. Loose Washer ties available by special order.
SNAP TIE HEAVY-3,350 Lbs. Hex Head. 1” x 1” Cone Tie or loose washer tie. Standard Breakback is 13/16” End
Wall
End
Wall Size
8-1/4” L & W Only Product Code No.
4-3/4” L & W Only Product Code No.
6”
20.21.51106
20.21.52106
8”
20.21.51108
20.21.52108
Breakback
PRODUCTS
1” x 1” Plastic Cone
80- TOOLS & PLACING
70- FOUNDATION
Wt. Lbs. per 100
7-5/8” 8”
60-PRECAST & TILT-UP
Contractor Committed.
STANDARD SNAP TIES- 2,250 Lbs.
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
46
9”
20.21.51109
20.21.52109
10”
20.21.51110
20.21.52110
11”
20.21.51111
12”
20.21.51112
20.21.52112
14”
20.21.51114
20.21.52114
16”
20.21.51116
20.21.52116
18”
20.21.51118
20.21.52118
22”
20.21.51122
20.21.52122
24”
20.21.51124
20.21.52124
32”
20.21.51132
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
A-5
Special Order
A-6
Special Order
SPANDREL PLATE TIE
A-7-A
50-FLATWORK ACCESSORIES
Special Order
A-8
Special Order
Up to 29-1/2” O.A.
Product Code No.
Wt. Lbs. per 100 36.8
80- TOOLS & PLACING
HEAVY DUTY SNAP TIE WEDGES Product Code No. 20.20.20010
www.atlasform.com
PRODUCTS
A-9
Special Order
70- FOUNDATION
TIP TO TIP TIE - 2,250 LBS.
60-PRECAST & TILT-UP
WATER SEAL FOR SNAP TIES
Length
40-BAR SUPPORTS
A-7
Special Order
30-ATLAS TECH PRODUCTS
SPANDREL HOOK TIE
20-FORMING ACCESSORIES
SPANDREL POINT TIE
10-FORMING & SHORING
THREADED PULLOUT TIE 1,875 LBS.
47
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
A-21-F
Contractor Committed.
FLAT TIE Special Order
Wall Size
A-21-K
Product Code No.
Wt. Lbs. per 100
8”
24.0
10”
28.4
12”
32.8
TIE KEY
30-ATLAS TECH PRODUCTS
Special Order Product Code No.
A-21-U
Wt. Lbs.
Packaging
50.0 per carton
1,000 per carton
STRAP TIE Special Order Wt.Lbs. per 100
A-21-X
20.6
8”
30.4
10”
34.8
12”
39.0
14”
41.2
16”
45.6
X-FLAT TIE Heavy Duty available upon request.
PRODUCTS
Wall Size
Product Code No.
6”
20.22.20006
8”
20.22.20008
10”
20.22.20010
11”
20.22.20011
12”
20.22.20012
15”
20.22.20015
18”
20.22.20018
24”
20.22.20024
80- TOOLS & PLACING
70- FOUNDATION
Product Code No.
6”
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
Wall Size
48
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
A-22
Wall Size
End Size
6” 8” 10”
Product Code No.
Wt. Lbs. per 100
Packaging
3/4”
36.3
100 per carton
3/4”
43.1
100 per carton
3/4”
47.9
100 per carton
3/4”
52.7
100 per carton
6”
1-1/8”
41.0
100 per carton
8”
1-1/8”
47.8
100 per carton
10”
1-1/8”
52.6
100 per carton
12”
1-1/8”
57.4
100 per carton
Type
Product Code No.
Wt. Lbs.
A-27
20.20.00100
7.0 Ea.
A-27-M
A-27
7.0 Ea.
A-29
40-BAR SUPPORTS
SNAP TIE SHANK WRENCH
30-ATLAS TECH PRODUCTS
TURNBUCKLE FORM ALIGNER
20-FORMING ACCESSORIES
12”
10-FORMING & SHORING
SPREADER CLEATS
Special Order
Special Order Wt. Lbs. per 100 2.3 Ea.
BREAKBACK WRENCH
A-30
50-FLATWORK ACCESSORIES
Product Code No.
Special Order 60-PRECAST & TILT-UP
Product Code No.
Wt. Lbs. 1.5 Ea.
PRODUCTS
A heavy-duty tool that has many uses on any jobsite, from stripping forms to jockeying tilt-up panels. The handle is fabricated from 1x2 tubular steel that is carefully mig-welded to a heat-treated milled blade. Product Code No.
Wt. Lbs.
80.48.6200
15.0 Ea.
5” Blade
80- TOOLS & PLACING
Type 3” Blade
15.0 Ea.
www.atlasform.com
70- FOUNDATION
BETTER BAR/ FORM STRIPPING BAR
49
10-FORMING & SHORING
FORMING ACCESSORIES
A-31
Contractor Committed.
WRENCH HEAD SNAP TIE SOCKET For breaking back Sure-Snap Hex Head
Special Order Type
Product Code No.
A-35
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
0.8 Ea.
STRONGBACK TIE Special Order Length
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
Hex A-31
Wt. Lbs.
Product Code No.
7-1/2”
A-40
Wt. Lbs. .250 Ea.
CONE REMOVAL WRENCH Product Code No. 20.35.70010
A-44
STAINLESS STEEL SNAP TIE Atlas Construction Supply cannot guarantee a proper breakback due to variations of properties in stainless steel wire.
A-45 PRODUCTS
70- FOUNDATION
60-PRECAST & TILT-UP
Special Order
BASE TIE Wall Size
Product Code No.
6”
20.22.30006
8”
20.22.30008
9”
20.22.30009
10”
80- TOOLS & PLACING
12”
50
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
A-46 A-48
A-46 LOOP PANEL TIE 2,250 Lbs. Standard
3,000 Lbs. Heavy Duty
Product Code No.
Wall Size
6”
20.22.10006
6”
7”
Product Code No.
20-FORMING ACCESSORIES
Wall Size
8”
7” 20.22.10008
8”
10”
20.22.10010
10”
12”
20.22.10012
12”
13”
20.22.10013
14”
14”
20.22.10014
15”
15”
20.22.10015
16”
16”
20.22.10016
18”
18”
20.22.10018
20”
20”
20.22.10020
24”
24”
20.22.10024
28”
20.22.10028
30”
20.22.10030
32”
20.22.10032
36”
20.22.10036
40”
20.22.10040
9”
9”
30-ATLAS TECH PRODUCTS 40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
A-48 GANG LOOP PANEL TIE Special Order
3,000 Lbs Heavy Duty Wall Size
10-FORMING & SHORING
LOOP TIES
Product Code No.
6”
60-PRECAST & TILT-UP
7” 8” 10” 12” 13” 14”
PRODUCTS
16” 18” 20” 24”
80- TOOLS & PLACING
Available in full cartons only. All other sizes and conditions available.
www.atlasform.com
70- FOUNDATION
15”
51
A-49
A-46 LOOP PANEL TIES FRACTION OR SPECIAL BREAKBACK A-46 LOOP PANEL TIE WATER RESISTANT A-46 LOOP PANEL TIE WITH CONES A-46 LOOP PANEL TIE WATER RESISTANT WITH CONES
A-51
40-BAR SUPPORTS
WEDGE BOLT Product Code No.
Wt. Lbs. per 100
Packaging
12.55.60058
12.0
500 per pail
Available in full pails only.
A-52
Z TIE HOLDER Product Code No.
Wt. Lbs. per 100
Packaging
12.55.60056
70.0
50 per carton
Available in full cartons only.
A-53
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
LOOP TIES (SPECIAL)
WALER TIE Size
Product Code No.
Wt. Lbs. per 100
Packaging
2x4
12.55.60062
11.5
200 per carton
2x6
12.22.60063
14.0
200 per carton
PRODUCTS
Available in full cartons only.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
Special Order
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
52
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
Size
Product Code No.
Wt. Lbs. per 100
Packaging
1” x 1” Snap Tie Cone Plugs
20.28.40010
2.4
1000 per carton
A-55
With 1” x 1” self-centering plastic cone
Special Order Wall Size
Product Code No.
Wt. Lbs. per 100 18.0
7”
19.0
7-5/8”
20.0
8”
21.0 22.0
10”
23.0
11-5/8”
25.0
12”
26.0
14”
29.0
15”
31.0
16”
32.0
18”
33.0
20”
35.0
24”
40.0
50-FLATWORK ACCESSORIES
9”
40-BAR SUPPORTS
6”
A-56
60-PRECAST & TILT-UP
Sold only in boxes of 100 ties with 1” x 1” self-centering plastic cone. Other Non-Stock ties available with 15/16” ends.
SURE-LOCK BRACKET
30-ATLAS TECH PRODUCTS
SURE-LOCK TIE - 2,250 LBS.
20-FORMING ACCESSORIES
For filling holes left by plastic cones; eliminates job patching problems. Use Atlas Acryl Bond or Epoxy Bonder to glue in the plug. Stocked in Grey only Available in full cartons only.
10-FORMING & SHORING
A-54
CONCRETE PLUGS
Special Order Packaging
1.4 Ea.
50 per carton
PRODUCTS
Wt. Lbs.
70- FOUNDATION
Product Code No.
80- TOOLS & PLACING
www.atlasform.com
53
A-56-A
40-BAR SUPPORTS
Contractor Committed.
SPEEDY BRACKET Special Order
Product Code No.
Wt. Lbs. 1.5 Ea.
A-57
SURE-LOCK® STRONGBACK Special Order
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
Product Code No.
A-57-A
Wt. Lbs.
Packaging
0.5 Ea.
100 per carton
STIFFBACK BRACKET Special Order Product Code No.
Wt. Lbs.
50-FLATWORK ACCESSORIES
1.3 Ea.
A-58
SURE PLUG
60-PRECAST & TILT-UP
FOR PLUGGING HOLES IN CONCRETE AFTER REMOVING TAPER TIES Size
Nominal Dia.
Length
Product Code No.
Wt. Lbs. per 100
16
1”
1-1/4”
20.28.30010
4.8
18
1-1/8”
1-3/8”
20.28.30020
5.2
20
1-1/4”
1-3/8”
20.28.30030
7.3
PRODUCTS
70- FOUNDATION
Other sizes available
A-59
SURE PLUG INSERTION TOOL FOR INSERTION OF THE A-58 SURE PLUGS
Special Order Plug Size
Product Code No.
11
80- TOOLS & PLACING
14-16 18-20 22-24
Note: To order complete A-59 Insertion Tool specify the size of plug. Stems for plug sizes 16, 20 and 24 are interchangeable in a common insertion tool. The stem for plug size 11 will work only with the insertion tool made for size 11 plugs.
54
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
A-63
Size
Product Code No.
Packaging
4” x 4”
15.5
100 per carton
4” x 6”
17.6
100 per carton
6” x 6”
19.6
100 per carton
Available in full cartons only.
JAHN “A” BRACKET
A-81
U.S. Patent No. 2,967,689
Wt. Lbs.
Packaging
20.20.10001
1.4 Ea.
50 per carton
30-ATLAS TECH PRODUCTS
Product Code No.
Available in full cartons only. Jahn “A” bracket; use with loose 2 x 4 walers and plywood for forming any type wall Eccentric compensates for 2 x 4 variations
A-82
U.S. Patent No. 2,967,689 Product Code No.
Wt. Lbs.
Packaging
20.20.10002
1.1 Ea.
75 per carton
50-FLATWORK ACCESSORIES
Available in full cartons only. Jahn “C” bracket; for attaching vertical strong-backs where alignment is needed - high walls, foundations
JAHN CORNERLOCK Product Code No.
Wt. Lbs.
Packaging
20.20.10010
2.0 Ea.
20 per carton
A-83 60-PRECAST & TILT-UP
U.S. Patent No. 3,771,757
Wt. Lbs.
Packaging
20.20.10020
0.2 Ea.
100 per carton
80- TOOLS & PLACING
Product Code No.
Available in full cartons only. Jahn Tie Extender; converts short-end snap tie into a long-end snap tie.
www.atlasform.com
PRODUCTS
A-86
U.S. Patent No. 3,203,717
70- FOUNDATION
Available in full cartons only. Jahn Cornerlock; for outside corners, pilasters and columns Quickly locks outside corners with cam action handle Can be used with other forming systems
JAHN TIE EXTENDER
40-BAR SUPPORTS
JAHN “C” BRACKET
20-FORMING ACCESSORIES
Wt. Lbs. per 100
10-FORMING & SHORING
LOOP STRONGBACK TIE Special Order
55
A-87
50-FLATWORK ACCESSORIES
Contractor Committed.
JAHN RIVET FOR JAHN A & C BRACKETS Special Order Product Code No.
A-88
JAHN ECCENTRIC FOR JAHN A & C BRACKETS Special Order Product Code No.
A-89
JAHN SCAFFOLD JACK U.S. PATENT NO. 3,000,605
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
Product Code No.
Wt. Lbs.
20.20.10040
17.0 Ea.
Jahn Scaffold Jack; one piece all-steel unit, easily attaches to Waler Brackets For 24” x 24”, 16” x 24” or 16” x 16” tie spacings
A-90
SCAFFOLD BRACKET (JACK) MEETS OSHA REQUIREMENTS
Special Order
Wt. Lbs. 23.0 Ea.
PRODUCTS
A-97
A-100
4 X 4 POST SHORE CLAMP Product Code No.
Wt. Lbs.
Packaging
20.10.31010
3.050 Ea.
1 bag (20 pcs.)
SPEED STEP Special Order
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Product Code No.
Product Code No.
Wt. Lbs. 0.8 Ea.
Packaged Ten (10) pcs. per carton.
56
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
Special Order
B-1/B-3, 1/2” Dia. (4,500 Lbs.) Standard 2-Struts
B-1, 1/2”” Dia. (6,750 Lbs.) Heavy 2-Struts
B-1/B-3, 1/2” Dia. (6,750 Lbs.) Heavy 2-Struts
Various Sizes Available Special Order
Various Sizes Available Special Order
Various Sizes Available Special Order
Various Sizes Available Special Order
B-1, 3/4” Dia. (9,000 Lbs.) Heavy 2-Struts
B-1/B-3, 3/4” Dia. (9,000 Lbs.) Heavy 2-Struts
Various Sizes Available Special Order
Various Sizes Available Special Order
Various Sizes Available Special Order
Various Sizes Available Special Order
B-2, 1” Dia. (18,000 Lbs.) Standard 4-Struts
B-2, 1-1/4” Dia. (27,000 Lbs.) Heavy 4-Struts
Various Sizes Available Special Order
Various Sizes Available Special Order
Various Sizes Available Special Order
50-FLATWORK ACCESSORIES
B-1, 1” Dia. (13,500 Lbs.) Standard 2-Struts
40-BAR SUPPORTS
B-1/B-3, 3/4” Dia. (6,750 Lbs.) Standard 2-Struts
30-ATLAS TECH PRODUCTS
B-1, 3/4” Dia. (6,750 Lbs.) Standard 2-Struts
20-FORMING ACCESSORIES
B-1, 1/2” Dia. (4,500 Lbs.) Standard 2-Struts
10-FORMING & SHORING
B-1 B-3 B-4
COIL TIES
† Neoprene Water Seal furnished as standard, metal Water Seal available on special order.
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
57
B-6
WELDING COIL TIE Size
Wire Strut Diameter
AISI No.
Product Code No.
1/2” Dia.x 4”
.306”
1008
23.0
3/4” Dia.x 6”
.375”
1018
54.0
1” Dia. x 8”
.440”
1038
100.0
1-1/4” Dia. x 8”
.440”
1038
100.0
2 AND 4 STRUT COIL INSERT (CRIMP)
B-11
FLAT WASHER
Special Order
50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
Plate Size
3/4” Hole Product Code No.
3” x 3” x 1/4”
20.40.83933
3” x 3” x 3/8”
20.40.83833
3” x 4” x 3/8”
20.40.83834
4” x 4” x 3/8”
20.40.83844
4” x 4” x 1/2” 5” x 5” x 3/8”
20.40.83855
5” x 5” x 1/2” 6” x 6” x 3/8” 6” x 6” x 1/2”
20.40.83766
8” x 8” x 5/8”
20.40.83688
PRODUCTS
Other sizes available upon request
80- TOOLS & PLACING
70- FOUNDATION
Wt. Lbs. per 100
B-7 B-22
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
Contractor Committed.
Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
58
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
B-12
HIGH TENSILE STRENGTH (MINIMUM SAFETY FACTOR 2 TO 1) SEE PRODUCT P-49 FOR LOW TENSILE STRENGTH ROD Stock Length
Safe Working Load (Lbs.)
Product Code No.
Wt. Lbs./Ft.
1/2”
12’
9,000
20.30.37012
0.530
3/4”
12’
18,000
20.30.35012
1.150
1”
12’
38,000
20.30.33012
2.040
1-1/4”
12’
56,000
20.30.32012
3.480
1-1/2”
12’
68,000
20.30.31012
6.010
Note:
20-FORMING ACCESSORIES
Dia.
30-ATLAS TECH PRODUCTS
Left-handed coil thread available. 1-1/8” diameter available on request. For lengths less than 12 ft. see D-18. Longer lengths available. 5/8” and 7/8” available on request.
D/R THREADED BAR HIGH STRENGTH BENDABLE AND WELDABLE CONTINUOUS THREAD (2-1/2 THREADS PER INCH) 5/8” AND 7/8” INCH DIAMETERS ONLY.
Safe Working Load (Lbs.)
Product Code No.
Weight Lbs./Ft.
5/8”
20’-0”
20,000
20.35.16012
1.00
20.35.16910
Wing Nut Bracket
20.35.16920
5/8” Cone
20.35.50006
50-FLATWORK ACCESSORIES
Stock Length
40-BAR SUPPORTS
Dia.
Wing Nut
5/8” Coupler
7/8”
20’-0”
32,000
20.35.14012 20.35.14910 20.35.14920
7/8” Cone
20.35.50004
1.550
60-PRECAST & TILT-UP
Wing Nut Wing Nut Bracket
7/8” Coupler
B-13
Dia.
Product Code No.
1/2”
20.30.80701
5/8”
20.30.80601
3/4”
20.30.80501
PRODUCTS
FOR HEAVY COIL HEX NUTS, SEE B-25
70- FOUNDATION
COIL NUTS
10-FORMING & SHORING
COIL ROD
7/8” 20.30.80301
1-1/4”
20.30.80201
1-1/2”
20.30.80101
Note:
80- TOOLS & PLACING
1”
Left-handed coil threaded nuts available. Stainless steel Coil Nuts available.
www.atlasform.com
59
B-14
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
Contractor Committed.
COIL BOLTS
1/2” Diameter
(4,125 Lbs.) (6,750 Lbs.) †
Bolt Length
Product Code No.
1-1/2” 2”
20.30.47020
2-1/2”
20.30.47025
3”
20.30.47030
3-1/2”
20.30.47035
30-ATLAS TECH PRODUCTS
4”
20.30.45020 20.30.45025
3”
20.30.45030
3-1/2”
20.30.45035
4”
20.30.45040
20.30.45060
8”
8”
9”
9”
10” 20.30.47100
11” 12”
12”
40-BAR SUPPORTS
2” 2-1/2”
7”
7”
20.30.45120
13”
13”
14”
14”
15”
15”
16”
16”
17”
17”
50-FLATWORK ACCESSORIES
Product Code No.
6”
6”
11”
18”
18”
1” Diameter
(18,000 Lbs.)
1-1/4” Diameter
(27,000 Lbs.)
Bolt Length
Product Code No.
Bolt Length
Product Code No.
4”
20.30.43040
4”
6”
20.30.43060
6”
8”
20.30.43080
60-PRECAST & TILT-UP
10” 12”
20.30.43120
14”
8”
12” 14”
16”
16”
18”
PRODUCTS
20.30.42060
10”
18”
20”
20.30.43200
24”
20.30.43240
30”
20.30.43300
1-1/2” Diameter
(41,250 Lbs.)
36”
20.30.43360
Bolt Length
Product Code No.
20.43480
6”
20.30.41060
48”
† All 1/2” diameter Coil Bolts less than 6” long have a rated work load of 4,125 lbs. All 1/2” diameter Coil Bolts 6” or longer have a rated work load of 6,750 lbs.
80- TOOLS & PLACING
70- FOUNDATION
(9,000 Lbs.)
Bolt Length
5”
5”
10”
3/4” Diameter
60
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
B-14-A
Special Order
Length
1/2”
12”
1/2” 1/2”
Product Code No.
Wt. Lbs.
Dia.
Length
Product Code No.
75.0
3/4”
12”
148.0
16”
91.8
3/4”
16”
186.0
18”
100.0
3/4”
18”
205.0
1/2”
20”
108.2
3/4”
20”
224.0
1/2”
24”
125.0
3/4”
24”
262.0
B-14-W
Special Order Dia.
Product Code No.
1/2”
Wt. Lbs. per 100
30-ATLAS TECH PRODUCTS
WALE BOLT ASSEMBLY
Wt. Lbs. per 100
20-FORMING ACCESSORIES
Dia.
10-FORMING & SHORING
ADJUSTABLE COIL BOLT
173.5
40-BAR SUPPORTS
B-15
Special Order Cone Size
Product Code No.
Wt. Lbs.
For 1/2” Plastic Cone
1.6 Ea.
For 3/4” Plastic Cone
1.9 Ea. 2.4 Ea.
For 1-1/4” Plastic Cone
3.3 Ea.
COIL LOOP INSERT STRAIGHT Product Code No.
Wt. Lbs. per 100
1/2”
3-1/2”
20.41.17035
1/2”
4”
20.40.17040
18.0
1/2”
6”
20.40.17060
30.2
3/4”
4”
20.41.15040
37.6
3/4”
6”
20.41.15060
39.2
3/4”
9”
1”
4”
20.41.13040
1”
6”
20.40.13060
1”
8”
PRODUCTS
Length
70- FOUNDATION
Dia.
B-16
60-PRECAST & TILT-UP
For 1” Plastic Cone
50-FLATWORK ACCESSORIES
PLASTIC CONE REMOVAL WRENCH
80.5
80- TOOLS & PLACING
† Minimum concrete strength of 2,000 psi; Safe Working Loads shown with 4 to 1 safety factor are 1/4 of the approximate ultimate strength based on the mechanical strength of the strut wire and welds.
www.atlasform.com
61
B-17
B-18
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
DOUBLE FLARED COIL LOOP INSERT Safe Load Lbs. with 4 to1 Safety Factor
Dia.
Length
Product Code No.
Wt. Lbs./ Ea.
9,500
1”
12”
2.37
9,500
1-1/4”
12”
2.45
9,500
1-1/2”
12”
2.65
13,500
1”
12”
3.12
13,500
1-1/4”
12”
3.20
13,500
1-1/2”
12”
3.40
B-35 Machine Threads available † Minimum concrete strength of 2,000 psi; Safe Working Loads shown with 4 to 1 safety factor are 1/4 the approximate ultimate strength based on the mechanical strength of the strut wire and welds.
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
Contractor Committed.
Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
SINGLE FLARED COIL LOOP INSERT Safe Load Lbs. with 4 to 1 Safety Factor
Dia.
Length
2,250
1/2”
4”
2,250
1/2”
6”
0.25
2,250
1/2”
9”
0.307
2,250
1/2”
12”
3,750
3/4”
6”
20.41.35060
0.608
3,750
3/4”
9”
20.41.35090
0.790
3,750
3/4”
12”
1.114
4,500
3/4”
9”
1.250
4,500
3/4”
12”
4,500
1”
6”
4,500
1”
9”
20.41.33090
0.675
4,500
1”
12”
20.41.33120
1.200
20.41.32120
1.850
7,675
1”
12”
7,675
1-1/4”
12”
7,675
1-1/2”
12”
Product Code No.
Wt. Lbs./Ea.
0.21
0.583
1.521 20.41.33060
0.520
1.770
2.050
B-35 Machine Threads available † Minimum concrete strength of 2,000 psi; Safe Working Loads shown with 4 to 1 safety factor are 1/4 the approximate ultimate strength based on the mechanical strength of the strut wire and welds.
B-20
WALE HOLDER Special Order
80- TOOLS & PLACING
Size
62
Product Code No.
Wt.Lbs. per 100
1/2” Coil
25.0
3/4” Coil
36.5
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
B-21
Thread Length
O.A. Length
1/2”
3”
5-3/4”
Product Code No.
Wt. Lbs. per 100 24.3
1/2”
3-1/2”
6-1/4”
26.0
1/2”
4”
6-3/4”
28.8
1/2”
4-1/2”
7-1/4”
31.0
1/2”
6”
8-3/4”
37.6
1/2”
7”
9-3/4”
42.0
1/2”
8”
10-3/4”
46.4
1/2”
10”
12-3/4”
55.3
1/2”
12”
14-3/4”
64.0
1/2”
14”
16-3/4”
73.0
(1/2” Coil Thread)
20-FORMING ACCESSORIES
Dia.
Special Order Height
1/2”
1-3/16”
Product Code No.
Wt. Lbs./Ea 0.300
5/8”
1-3/16”
0.265
3/4”
1-3/16”
0.230
1”
2”
0.538
1-1/4”
2-1/2”
1.500
1-1/2”
3-3/8”
3.130
40-BAR SUPPORTS
Dia.
B-27
Size
Washer Dia.
Product Code No.
Wt. Lbs. per 100
1/2”
4”
20.30.87003
161.4
3/4”
4”
20.30.55003
161.4
7/8”
5”
225.0
1”
5”
225.0
50-FLATWORK ACCESSORIES
COIL NUT WASHER
Setback
Wt. Lbs. per 100
B-30: Screw-on Cone Plastic Product Code No.
Wt. Lbs. per 100
1”
4.1
4.5
1/2”
1-1/2”
5.1
5.2
1/2”
2”
6.6
6.9
3/4”
1”
6.0
6.6
3/4”
1-1/2”
7.5
9.4
3/4”
2”
9.6
12.3
1”
1”
1”
2”
1”
2-1/2” 2” 2-1/2”
14.8
80- TOOLS & PLACING
1-1/4” 1-1/4”
PRODUCTS
1/2”
70- FOUNDATION
B-29: Loose Cone Plastic Product Code No.
B-29 B-30
60-PRECAST & TILT-UP
PLASTIC CONES FOR COIL TIES Special Order Bolt Dia.
30-ATLAS TECH PRODUCTS
B-25
HEAVY COIL HEX NUTS
10-FORMING & SHORING
PLY LAG (FOR STEEL-PLY FORMING) Special Order
16.6 18.8 16.6 19.8
Overall length of B-29 same as setback.
www.atlasform.com
63
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
B-31
Contractor Committed.
ROCK ANCHOR (COIL THREAD) Special Order
B-32
Size
Hole Dia.
Depth
Product Code No.
Wt. Lbs. per 100
1/2”
1-3/8”
6”
66.8
3/4”
1-5/8”
8”
95.2
1”
1-3/4”
10”
96.6
HANDLE COIL NUT Size
B-33
PRODUCTS
Product Code No.
Wt. Lbs. per 100
1/2”
21.0
3/4”
38.5
1”
77.0
DOUBLE FLARED CRISS CROSS COIL LOOP INSERT Safe Load Lbs. with 4 to 1 Safety Factor
Dia.
Length
Plain Product Code No.
9,500
1”
12-3/8”
237.0
9,500
1-1/4”
12-3/8”
245.0
9,500
1-1/2”
12-3/8”
266.0
13,500
1”
12-1/2”
312.0
13,500
1-1/4”
12-1/2”
20.41.42125
320.0
13,500
1-1/2”
12-1/2”
20.41.41125
341.0
Galvanized Product Code No.
Wt. Lbs. per 100
† Minimum concrete strength of 2,000 psi; Safe Working Loads shown with 4 to 1 safety factor are 1/4 of the approximate ultimate strength based on the mechanical strength of the strut wire and welds.
B-37
TOGGLE COIL TIES Special Order Available only in 1/2” diameter.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
Special Order
64
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
Size
Product Code No.
Wt. Lbs. per 100
1/2”
20.30.80702
65.0
3/4”
20.30.80502
B-39
90.0
7/8”
107.0 20.30.80302
107.0
1-1/4”
20.30.80202
122.0
1-1/2”
20.30.80102
286.0
1-1/8”
114.0
PLASTIC SETBACK PLUG
B-40
Color
Wt. Lbs. per 100
1/2”
Product Code No.
Light Gray
0.94
1/2”
Dark Gray
0.94
3/4”
Light Gray
1.85
30-ATLAS TECH PRODUCTS
Special Order
B-42
Special Order Product Code No.
40-BAR SUPPORTS
BATTER WASHER (1/2”, 3/4” & 1”) Size
20-FORMING ACCESSORIES
1”
Size
10-FORMING & SHORING
WING NUT (COIL THREAD)
Wt. Lbs. per 100 100.0
3/4”
250.0
1”
400.0
50-FLATWORK ACCESSORIES
1/2”
For larger sizes see D-22 Batter Washer
Special Order Dia.
Length
18,000
1-1/4”
12”/15”
Product Code No.
Wt. Lbs. per 100 450.0
PRODUCTS
† Minimum concrete strength of 2,000 psi; Safe Working Loads shown with 4 to 1 safety factor are 1/4 of the approximate ultimate strength based on the mechanical strength of the strut wire and welds.
70- FOUNDATION
Safe Load Lbs. With 4 to 1 Safety Factor
60-PRECAST & TILT-UP
B-43
TRIPLE FLARED COIL LOOP
80- TOOLS & PLACING
www.atlasform.com
65
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
D-1 D-18
Contractor Committed.
INSIDE TIE ROD Special Order On D-1 Tie Rods, flats are the only anti-turn device furnished Minimum Tie Rod length for flats:
1/2” dia. 5/8” dia. 3/4” dia. 1” dia.
6” 6” 6” 8”
D-1 COIL OR NC THREADS ENDS ONLY
30-ATLAS TECH PRODUCTS
Tie Length
Product Code No.
Product Code No.
Product Code No.
Product Code No.
1/2” Dia. Heavy (9,000 Lbs)
5/8” Dia. Heavy (12,000 Lbs)
3/4” Dia. Heavy (18,000 Lbs)
1” Dia. Heavy (38,000 Lbs)
6” 7” 8” 9” 10” 11”
40-BAR SUPPORTS
12” 13” 14” 15” 16” 17”
50-FLATWORK ACCESSORIES
18”
Longer lengths available upon request.
D-18 CONTINUOUS COIL THREADS Tie Length
Product Code No.
Product Code No.
Product Code No.
Product Code No.
Product Code No.
Product Code No.
1/2” Dia. Heavy (9,000 Lbs)
5/8” Dia. Heavy (12,000 Lbs)
3/4” Dia. Heavy (18,000 Lbs)
1” Dia. Heavy (38,000 Lbs)
1-1/4” Dia. Heavy (56,000 Lbs)
1-1/2” Dia. Heavy (68,000 Lbs)
60-PRECAST & TILT-UP
6” 8” 10” 12” 14”
16”
PRODUCTS
70- FOUNDATION
15”
18” 20” 22” 24” 30”
80- TOOLS & PLACING
36”
66
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
D-1-J D-1-L D-1-LA
D-1-J Bolt 1/2” Dia. X 1-1\2” end Size
Product Code No.
Wt. Lbs. per 100
2”
20.25.37002
9.0
3”
20.25.37003
13.4
4”
20.25.37004
17.8
6”
20.25.37006
26.6
3-1/2”
3-1/2”
8”
20.25.37008
35.4
4”
4”
24.4
10”
20.25.37010
44.2
4-1/2”
4-1/2”
26.6
12”
20.25.37012
28.8
D-1-LA Bolt 1/2” Dia. X 1-1\2” end
D-1-L Bolt 1/2” Dia. X 1-1\2” end Product Code No.
Size
Product Code No.
Wt. Lbs. per 100 22.2
5”
5”
61.8
5-1/2”
5-1/2”
31
18”
79.4
6”
6”
33.2
88.2
6-1/2”
6-1/2”
35.4
20”
20.25.37020
30-ATLAS TECH PRODUCTS
53.0
14”
D-1-J BOLT CLAMP For 3/4” Dia. J-Bolt Wt. Lbs./Ea.
20.20.27010
0.2 Ea.
D-1-PA
ANCHOR BOLT Length
1/2”
6”
Product Code No.
Bolt Dia.
Length
5/8”
6”
50-FLATWORK ACCESSORIES
Bolt Dia.
Product Code No.
8”
5/8”
8”
1/2”
10”
60.25.27010
5/8”
10”
60.25.26010
1/2”
12”
60.25.27012
5/8”
12”
60.25.26012
1/2”
14”
5/8”
14”
1/2”
16”
5/8”
16”
60.25.26016
1/2”
18”
5/8”
18”
60.25.26018
60-PRECAST & TILT-UP
1/2”
PRODUCTS
Special Order Shell Size
1/2” x 3/4”
Product Code No.
Wt. Lbs. Per Carton
2” x 5”
100 Per Ct.
8.0
5/8”, 3/4”, & 7/8”
2” x 7”
100 Per Ct.
10.0
1” & 1-1/4”
3” x 10”
50 Per Ct.
13.0
1-1/2” & 1-3/4”
4” x 15”
20 Per Ct.
12.0
2” & 2-1/4”
4” x 18”
20 Per Ct.
15.0
2-1/2” & 3”
6” x 24”
10 Per Ct.
18.0
4” & 5”
6” x 24”
10 Per Ct.
18.0
80- TOOLS & PLACING
Packaging
Sizes for smooth round bars. When using rebar, increase anchor-bolt sleeve by 1/4”.
www.atlasform.com
70- FOUNDATION
D-1-S
ANCHOR BOLT SLEEVES Bolt Diameters
40-BAR SUPPORTS
Product Code No.
20-FORMING ACCESSORIES
Size
10-FORMING & SHORING
D-1-J BOLT, D-1-L BOLT, D-1-LA BOLT
67
D-2
40-BAR SUPPORTS
SHE BOLT (OUTSIDE STUD ROD) Dia.
Threads Per Inch
Overall Length
Product Code No.
Wt. Lbs.
3/4”
3-1/3”
20”
20.30.25020
2.0 Ea.
3/4”
-
17”
20.30.25017
2.0 Ea.
3/4”
-
24”
20.30.25024
2.0 Ea.
3/4” diameter Acme Thread (external) for 1/2” diameter— Inside Tie Rod with NC threads. She Bolts with coil threads and larger sizes see D-30. West Coast Acme Thread is 5 threads per inch. Caution: Acme Thread pitch varies from region to region.
D-4
D-6
HEX COUPLING NUT (NC THREADS) Dia.
Length
Threads Per Inch
Product Code No.
3/8”
1-3/4”
16
20.40.68001
11.0
1/2”
1-3/4”
13
20.40.67005
18.1
3/4”
2-1/4”
10
20.40.65001
27.0
7/8”
2-1/2”
9
20.40.64001
42.0
1”
2-3/4”
8
20.40.63005
60.0
NUT WASHER (ACME) Dia.
Threads Per Inch
3/4”
3-1/3 Acme
Product Code No.
Wt. Lbs. 1.3 Ea
Dia.
Threads Per Inch
Product Code No.
Wt. Lbs.
1/2”
5 Acme
20.32.57003
1.4 Ea.
3/4”
5 Acme
20.32.55003
1.3 Ea.
Caution: Acme Thread pitch varies from region to region.
D-9
TAPER TIE (COIL) FOR DSI TAPER TIES SEE PAGE 45.
Tie Length
3/4” to 1/2” Dia. (7,500 Lbs.)
1” to 3/4” Dia. (18,000 Lbs.)
1-1/4” to 1” Dia. (34,000 Lbs.)
“1-1/2” to 1-1/4” Dia. (50,000 Lbs.)
Product Code No.
Product Code No.
Product Code No.
Product Code No.
PRODUCTS
30” 34”
20.30.16034
36”
20.30.16036
42” 43”
20.30.16043
48”
80- TOOLS & PLACING
70- FOUNDATION
Wt. Lbs./Ea.
West Coast
50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
Contractor Committed.
ACME THREAD
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
10.63.12048
52”
20.30.16052
54”
20.30.16054
60”
20.30.16060
72”
10.63.12072
80”
10.63.12078
Longer lengths available. Maximum length 80”.
68
10.63.12054
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
D-9-A
Taper Length
Taper Length
Overall Length
1
5/8”
13/16” to 5/8”
16”
41”
2
5/8”
13/16” to 5/8”
24”
49”
3
5/8”
13/16” to 5/8”
32”
57”
1
5/8”
1” to 5/8”
16”
41”
2
5/8”
1” to 5/8”
24”
49”
3
5/8”
1” to 5/8”
32”
57”
1
7/8”
1-1/4” to 7/8”
16”
42”
2
7/8”
1-1/4” to 7/8”
24”
50”
3
7/8”
1-1/4” to 7/8”
32”
58”
Product Code No.
D/R TAPER TIE
D-9-UHS
AVAILABLE WITH COIL THREADS ONLY Special Order
40-BAR SUPPORTS
75,000 Lb. Safe Work Load - 1-1/2” Diameter Coil Threads Each End Taper 1-3/4” - 1-1/2”.
Special Order Size No.
Rod Dia.
Product Code No.
Wt. Lbs. per 100
Clamps Per Carton
1
1/4”
38.2
50
2
3/8”
119.1
50
3
1/2”
202.0
50
50-FLATWORK ACCESSORIES
D-12
ROD CLAMP
30-ATLAS TECH PRODUCTS
Thread Dia.
20-FORMING ACCESSORIES
Size No.
10-FORMING & SHORING
D/R TAPER TIE Special Order
60-PRECAST & TILT-UP
Sold in full cartons only.
PENCIL ROD Special Order
1/4” Pencil Rod Coils
20.25.79012
3/8” Pencil Rod Coils
20.25.78012
D-12-A
1/4” and 3/8” diameter straight lengths available up to 20 ft. long.
PRODUCTS
Product Code No.
70- FOUNDATION
Type
1/4” Dia. Bright Basic, sold in full coils only. 80- TOOLS & PLACING
www.atlasform.com
69
D-12-F
Special Order Size
Product Code No.
Wt. Lbs. per 100 120.0
CLAMPING JACK FOR D-12 FORM CLAMP Size
Product Code No.
For 1/4” and 3/8” Rods
D-12-S
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
FORM CLAMP
Wt. Lbs. 8.0 Ea.
ROD CLAMP (SUPERIOR) Rod Dia.
Product Code No.
Wt. Lbs. per 100
Clamps Per Carton
1/4”
20.20.31010
38.2
100
3/8”
20.20.31015
70.6
50
Sold in full cartons only.
D-14
TIGHTENING WRENCH Rod Dia.
Product Code No.
Wt. Lbs.
1/4”
20.20.31020
1.3 Ea.
3/8”
1.3 Ea.
1/2”
1.3 Ea.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
Contractor Committed.
For 1/4” and 3/8” Rods
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
70
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
D-21
Wall Size
Product Code No.
Up to 12”
Wt. Lbs. per 100 25.0
BATTER WASHER
D-22
Special Order
30-ATLAS TECH PRODUCTS
Product Code No.
Wt. Lbs.
1-1/4-1-3/8”
5.5 Ea.
1-1/2-1-5/8”
5.5 Ea.
20-FORMING ACCESSORIES
To order: specify rebar diameter, distance between centerline of bar and face of concrete and wall thickness.
Bolt Dia.
10-FORMING & SHORING
REBAR CLIP AND SPREADER Special Order
For smaller size see B-42 Batter Washers.
AVAILABLE IN COIL OR NC THREAD
D-24
40-BAR SUPPORTS
ADJUSTABLE WELD ANGLE BRACKET Special Order Approx. Work Load Lbs. SWL 2 to 1
Bent Plate Product Code No.
Pivot Pin Product Code No.
Clip Product Code No.
Wt. Lbs. per 100
1/2”
9,000
320.0
5/8”
12,000
320.0
3/4”
18,000
320.0
7/8”
25,000
320.0
31,500
950.0
42,500
950.0
60-PRECAST & TILT-UP
1” 1-1/8”
50-FLATWORK ACCESSORIES
Thread Dia.
Pivot Pin furnished with coil thread. Threaded rod not included.
Dia.
Length
Product Code No.
Wt. Lbs. per 100
D-25 Bolt
9,000
2”
36.0
D-26 Bolt
12,000
-
18.0
PRODUCTS
Product
D-25 D-26
70- FOUNDATION
FITTING-UP BOLTS AND NUTS Special Order
80- TOOLS & PLACING
www.atlasform.com
71
10-FORMING & SHORING
FORMING ACCESSORIES
D-30
Contractor Committed.
SHE BOLT FURNISHED WITH COIL THREAD
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
She Bolt Dia.
Inside Tie Rod Dia.
Approx. Work Load Lbs.
Length
Product Code No. 20.30.25020
3/4”
1/2”
8,625
20”
7/8”
1/2” or 5/8”
9,000 or 12,000
18”
3.0
7/8”
1/2” or 5/8”
9,000 or 12,000
20”
3.7
7/8”
1/2” or 5/8”
9,000 or 12,000
24”
4.0
1”
5/8”
12,000
-
-
1-1/8”
3/4”
18,000
-
-
1-1/4”
3/4”
18,000
20”
20.30.22020
5.6
1-1/4”
3/4”
18,000
24”
20.30.22024
7.0
1-1/4”
3/4”
18,000
30”
20.30.22030
1-1/4”
3/4”
18,000
35”
1-3/8”
7/8” or 1”
31,000 or 33,750
-
-
1-1/2”
1”
37,500
20”
8.3
1-1/2”
1”
37,500
24”
10.2
1-1/2”
1”
37,500
30”
13.2
1”
37,500
35”
15.6
1-5/8”
1-1/8” or 1-1/4”
44,750 or 45,500
-
-
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
D/R SHE BOLT
Approx. Working Load Lbs.
Dia.
Length
18,000
5/8”
18”
5/8”
20”
5/8”
24”
5/8”
30”
7/8”
18”
7/8”
20”
7/8”
24”
7/8”
30”
18,000
32,000
PRODUCTS
70- FOUNDATION
9.1
1-1/2”
Special Order
32,000
80- TOOLS & PLACING
SWL: Safe working load at 2 to 1 factor of safety
72
-
11.8
† 5/8” diameter available by special order
D-30-A
Wt. Lbs.
www.atlasform.com
Product Code No.
Wt. Lbs. 4.9
7.0
7.2
10.2
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
D-32
Thread Rod Dia.
Length
Product Code No.
Wt. Lbs.
1/2”
2-1/2”
20.30.80705
0.2 Ea.
3/4”
3”
20.30.80505
0.4 Ea.
4”
1”
4-1/2”
20.30.80305
2.1 Ea.
0.9 Ea.
1-1/4”
5-1/2”
20.30.80205
2.8 Ea.
1-1/2”
7”
20-FORMING ACCESSORIES
7/8”
4.1 Ea.
Special Order Size 1-1/4” to 1” 1-1/2 “ to 1-1/4”
D-49
Special Order
40-BAR SUPPORTS
MAGNA JAW U.S. Patent No. 4,880,245
30-ATLAS TECH PRODUCTS
D-40
HE-BOLT
Product Code No.
10-FORMING & SHORING
CLOSED COUPLER
Wt. Lbs.
50-FLATWORK ACCESSORIES
8.0 Ea.
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
73
D-60 D-67
D-61 D-69
40-BAR SUPPORTS
FOR FIBERGLASS ROD Type
Dia.
Product Code No.
Wt. Lbs.
Packaging
D-60-G6000
0.306
20.20.33011
46.0 per pail
100 per pail
D-67-G15000
0.500
20.20.33005
52.0 per pail
50 per pail
SUPERTIE WEDGE FOR FIBERGLASS ROD Type
Product Code No.
Wt. Lbs.
Packaging
Fits Rod
D-61-H6000
20.20.33060
27.0 per carton
100 per carton
0.306
30.0 per carton
50 per carton
0.500
Available in full cartons only To be used with SuperTie Rod only
D-62 D-68
50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP PRODUCTS
SUPERTIE GRIPPER
D-69-H15000
SUPERTIE FIBERGLASS ROD Type
Standard Dia. x Length
Product Code No.
Wt. Lbs.
D-63 D-70
.306 x 12 ft.
20.25.68012
36.0 per bundle
600 ft. per bundle
D-62-R6/20G
.306 x 20 ft.
20.25.68020
60.0 per bundle
1000 ft. per bundle
D-68-R15/20G
.500 x 20ft.
20.25.67020
62.0 per bundle
360 ft. per bundle
SUPERTIE WATERSTOP FOR FIBERGLASS ROD Special Order Type
Product Code No.
Wt. Lbs.
Packaging
D-63-WS 6000
6.0 per carton
1,000 per carton
D-70- WS15000
8.0 per carton
1,000 per carton
Available in full cartons only To be used with SuperTie Rod only
D-64
SUPERTIE SPREADER CLIP FOR FIBERGLASS ROD Type
Product Code No.
Wt. Lbs.
Packaging
SC6000
20.20.33200
5.0 per carton
1,000 per carton
Available in full cartons only To be used with SuperTie Rod only
74
Packaging
D-62 - R6/12G
Available in full bundles only
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
Available in full cartons only To be used with SuperTie Rod only
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
F-1
Special Order Dia.
Length
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs. per 100
4”
23.8
1”
6”
54.0
1-1/4”
7”
80.6
1-1/2”
8”
89.4
2”
13”
-
SCREW ANCHOR BOLTS
F-2
Dia.
Length
Plain Product Code No.
Galvanized Product Code No.
30-ATLAS TECH PRODUCTS
USE ONLY WITH F-1 ANCHORS Wt. Lbs.
9”
121.0
1”
12”
261.0
1-1/4”
16”
565.0
1-1/2”
18”
954.0
1-3/4” and 2”
-
-
SCREW ANCHOR EYE BOLTS USE ONLY WITH F-1 ANCHORS EYE NUT WELDED TO ROD
F-3
Dia.
Length
3/4”
7”
Product Code No.
Wt. Lbs per 100
Ea. 1” Add Wt. Lbs.
155.0
12.5
1”
9”
376.0
22.3
1-1/4”
12”
757.0
35.0
1-1/2”
14”
1331.0
50.0
F-4
CUSTOM FABRICATED PRODUCT
PRODUCTS
F-4-T
70- FOUNDATION
SCREW ANCHOR SETTING BOLT TEMPLATE CUSTOM FABRICATED PRODUCT
60-PRECAST & TILT-UP
SCREW ANCHOR SETTING BOLT
50-FLATWORK ACCESSORIES
Special Order
40-BAR SUPPORTS
3/4”
20-FORMING ACCESSORIES
3/4”
10-FORMING & SHORING
SCREW ANCHORS
80- TOOLS & PLACING
www.atlasform.com
75
F-5
THREADED INSERTS Also see F-42, F-43 and F-44 Bolt Dia.
Type
Wt. Lbs. per 100
1/2’
13NC
35.0
5/8”
11NC
60.0
3/4”
10NC
51.3
7/8”
9NC
90.0
F-7
SHELF ANGLE INSERT Special Order Bolt Dia.
Type
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs. per 100
3/4”
F-7
108.0
3/4”
F-7-L
229.0
ASKEW HEAD BOLTS
50-FLATWORK ACCESSORIES
NC Threads Bolt Dia.
Length
3/4”
1-1/2”
25.0
3/4”
2”
31.0
3/4”
2-1/2”
37.0
3/4”
3”
43.0
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs. per 100
NUTS AND CUT WASHERS Type
Plain Product Code No.
Galvanized Product Code No.
Nut
11.9
3/4”
Washer
10.3
80- TOOLS & PLACING
76
Wt. Lbs. per 100
3/4”
PRODUCTS
60-PRECAST & TILT-UP
Bolt Dia.
70- FOUNDATION
Product Code No.
Also available electro galvanized.
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
Contractor Committed.
Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
Special Order For Cushion-Lock and Gasket-Lock Reglets see F-100 thru F-122 Type
Product Code No.
Quantity per skid
Galvanized Filled
40.0
6,000 ft.
Galvanized Open
37.0
6,000 ft.
Available only in bundles of 200 ft.
DOVETAIL ANCHOR SLOT
F-17
20-FORMING ACCESSORIES
Wt. Lbs. per 100 ft.
F-16
10-FORMING & SHORING
REGLET
Special Order Product Code No.
100 ft.
Wt. Lbs. per 100 ft.
Quantity per skid
30.0
6,000 ft.
30-ATLAS TECH PRODUCTS
Size
Available only in bundles of 250 ft.
Special Order Size
Length From Face of Concrete
F-21 Dovetail
16 ga.
3-1/2”
Corrugated Brick Anchor
50-FLATWORK ACCESSORIES
Product
5-1/2”
F-34
Special Order Length From Face of Concrete
F-34 Corrugated Wall Tie
26 ga. 7/8”
7”
F-34 Corrugated Wall Tie
16 ga. 7/8”
7”
Product Code No.
PRODUCTS
70- FOUNDATION
Size
60-PRECAST & TILT-UP
CORRUGATED WALL TIE Product
40-BAR SUPPORTS
F-21
DOVETAIL
80- TOOLS & PLACING
www.atlasform.com
77
10-FORMING & SHORING
FORMING ACCESSORIES
F-37
Contractor Committed.
WALL PLUG Special Order Size & Type
Product Code No.
Wt. Lbs. per 100
26 ga. Galv. Stock 2” wide
5.0
F-42
40-BAR SUPPORTS
LOOP FERRULE INSERT NC THREADS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
Minimum order of 500 pieces.
Bolt Dia.
Thread Type
Plain Product Code No.
Galvanized Product Code No.
1/4”
20 NC
3/8” 1/2”
Stainless Steel Product Code No.
Wt. Lbs. per 100
16 NC
20.42.10008
20.42.11008
14.9
13 NC
20.42.10007
20.42.11007
20.5
5/8”
11 NC
20.42.10006
3/4”
10 NC
20.42.10005
20.42.11005
37.5
7/8”
9 NC
47.5
1”
8 NC
57.0
13.5
33.5
† Type 304 stainless steel
F-44
THIN SLAB FERRULE INSERT
PRODUCTS
F-45
Bolt Dia.
Thread Type
1/4”
20 NC
3/8”
16 NC
20.42.30008
1/2”
13 NC
20.42.30007
5/8”
11 NC
20.42.30006
3/4”
10 NC
7/8”
9 NC
60.0
1”
8 NC
70.0
78
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs. per 100 16.9
20.42.31007
19.4 40.6 50.0
CAP PLUG Product Code No.
Stainless Steel Product Code No.
18.3
FOR USE WITH FERRULE INSERT Special Order Bolt Dia.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
NC THREADS
Wt. Lbs. per 100
3/8”
0.2
1/2”
0.2
5/8”
0.3
3/4”
0.4
1”
0.8
1-1/4”
1.0
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
F-47
Dia.
Height
3/4”
2-3/4”
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs. per 100 32.6
F-48
NC Threads Product Code No.
Coil Threads Product Code No.
1/2”
Wt. Lbs.
30-ATLAS TECH PRODUCTS
Dia.
0.7 Ea.
3/4”
20.30.80506
1.2 Ea.
1”
20.30.80306
2.8 Ea.
1-1/4”
6.0 Ea.
1-1/2”
6.0 Ea.
F-49
Bolt Dia.
Bolt Length
Product Code No.
Wt. Lbs.
1/2”
2-1/2”
20.30.57025
0.8 Ea.
3”
20.30.55030
1.3 Ea.
1”
3-1/2”
20.30.53035
3.7 Ea.
1-1/4”
4”
4.7 Ea.
1-1/2”
6”
9.3 Ea.
SHOULDER EYE BOLT
F-49-A
60-PRECAST & TILT-UP
3/4”
50-FLATWORK ACCESSORIES
COIL ROD WELDED TO EYE NUT
40-BAR SUPPORTS
Normally furnished with coil thread; can be furnished with National Coarse Thread.
EYE BOLT
20-FORMING ACCESSORIES
EYE NUT Special Order
10-FORMING & SHORING
DOUBLE FLARED LOOP INSERT Special Order
COIL THREADS WITH FORGED HEAD Product Code No.
Wt. Lbs.
3/4”
3-1/2”
20.30.55135
1.2 Ea.
1”
3-1/2”
20.30.53135
3.0 Ea.
PRODUCTS
Bolt Length
70- FOUNDATION
Bolt Dia.
80- TOOLS & PLACING
www.atlasform.com
79
F-50
Bolt Dia.
Thread Type
Product Code No.
Wt. Lbs. per 100
1/2”
13 NC
30.0
5/8”
11 NC
47.0
3/4”
10 NC
66.0
7/8”
9 NC
96.0
1”
8 NC
125.0
1-1/8”
7 NC
145.0
1-1/4”
7 NC
165.0
“L” LEG (THIN SLAB) FERRULE INSERT 4-STRUT WITH COIL Special Order
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
F-52
F-53
Bolt Dia.
Height
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs. per 100
3/4” - 10 NC
3-1/8”
71.0
1” - 8 NC
4-1/8”
99.0
“L” LEG (THIN SLAB) COIL INSERT 4-STRUT WITH COIL
PRODUCTS
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
ROCKET/KOHLER FERRULE INSERT
Bolt Dia.
Height
3/4”
3”
Plain Product Code No.
Galvanized Product Code No.
80
Wt. Lbs. per 100 67.0
3/4”
5”
20.41.55150
1”
3-1/2”
20.41.53035
1”
4”
20.41.53040
103.0
1”
5-1/2”
1-1/4”
4”
121.0
1-1/2”
4”
139.0
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
www.atlasform.com
20.41.53155
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
F-54
FOR DB-SAE-3 EMBED SEE D-108-A - CUSTOM FABRICATED PRODUCT
20-FORMING ACCESSORIES
F-54-RT
RAIL FASTENER EMBED (RT-SAE)
10-FORMING & SHORING
DUCTILE EMBED (SAE)
- CUSTOM FABRICATED PRODUCT
Threads
Insert Length
No. of Struts
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs.
F-56
3/4”
Coil
4-1/2”
2
F-57
3/4”
NC
4-5/8”
2
20.42.75045
20.42.75145
55.0
F-56
1”
Coil
5-1/2”
2
F-57
1”
NC
5-5/8”
2
117.0
F-58
1”
Coil
5-1/2”
4
163.0
F-59
1”
NC
5-5/8”
4
168.0
F-58
1-1/4”
Coil
7-1/2”
4
240.0
F-59
1-1/4”
NC
7-5/8”
4
315.0
F-60
1-1/2”
Coil
9-1/2”
6
420.0
F-61
1-1/2”
NC
9-5/8”
6
490.0
55.0
112.0
50-FLATWORK ACCESSORIES
Dia.
40-BAR SUPPORTS
Type
F-56 F-57 F-58 F-59 F-60 F-61
30-ATLAS TECH PRODUCTS
EXPANDED COIL INSERT
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
Note: For Safe Working Loads please contact an Atlas Representative. F-57 - 5/8” and 7/8” available upon request. F-57 With Washer- 1/2”, 5/8” and 7/8” available upon request. F-57, F-59, and F-61 available in stainless steel.
80- TOOLS & PLACING
www.atlasform.com
81
F-62
30-ATLAS TECH PRODUCTS
Contractor Committed.
FLARED THIN SLAB INSERT (FERRULE) WING NUT TYPE- NC THREADS Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
Bolt Dia.
Thread Type
Height
“E”
1/2”
13 NC
1-3/4”
4-1/2”
25.0
Wt. Lbs. per 100
11 NC
2-7/16”
4-7/8”
44.0
3/4”
10 NC
2-7/16”
4-7/8”
48.0
3/4”
10 NC
3-5/8”
4-7/8”
66.0
1”
8 NC
2-7/16”
5-1/8”
86.0
1”
8 NC
4-5/8”
5-1/8”
106.0
Note: For Safe Working Loads please contact an Atlas Representative. Available with mounting washer.
F-63
FLARED THIN SLAB INSERT (COIL) WING NUT TYPE
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
Height
“E”
Plain Product Code No.
Galvanized Product Code No.
Wt. Lbs. per 100
1/2”
1-3/4”
4-1/8”
20.41.67015
28.0
3/4”
2-5/16”
4-7/8”
20.41.65025
56.1
3/4”
3-1/2”
4-7/8”
20.41.65035
67.0
1”
2-5/16”
5-1/4”
20.41.63025
78.8
1”
4-1/2”
5-1/4”
20.41.63045
20.41.63145
97.0
Note: For Safe Working Loads please contact an Atlas Representative.
F-64
FERRULE LOOP INSERT NC THREAD
80- TOOLS & PLACING
PRODUCTS
60-PRECAST & TILT-UP
Galvanized Product Code No.
5/8”
Bolt Dia.
70- FOUNDATION
Plain Product Code No.
Bolt Dia.
Thread Type
Length
Plain Product Code No.
1/2”
13 NC
4-1/8”
24.7
1/2”
13 NC
6-1/8”
37.7
5/8”
11 NC
4-1/8”
5/8”
11 NC
6-1/8”
20.42.56006
47.7
Stainless Steel Product Code No.
Wt. Lbs. per 100
3/4”
10 NC
4-1/8”
20.42.55040
53.8
3/4”
10 NC
6-1/8”
20.42.55060
66.8
7/8”
9 NC
6-1/8”
1”
8 NC
6-1/8”
20.42.53060
74.8
1”
8 NC
6-1/8”
34.7
74.8
-Type 304 Stainless Steel. Available with mounting washer.
82
Galvanized Product Code No.
www.atlasform.com
102.3
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
F-65
Special Order 2-STRUT WITH COIL Dia.
L
1/2”
Product Code No.
Wt. Lbs. per 100 19.0
L
3/4”
24.0
20-FORMING ACCESSORIES
Type
2-STRUT WITH FERRULE Dia.
LF
1/2”
Product Code No.
Wt. Lbs. per 100 26.0
LF
5/8”
40.0
LF
3/4”
61.0
LF
1”
64.0
Open end Ferrule available Available in Stainless Steel and electro-galvanized.
TYPE L INSERTS WITH MOUNTING WASHER Special Order
F-65-W
40-BAR SUPPORTS
2-STRUT WITH COIL Type
Dia.
LW
1/2”
Product Code No.
24.0
LW
3/4”
35.0
Wt. Lbs. per 100
Type
Dia. 1/2”
Product Code No.
34.0
LF-W
5/8”
55.0
LF-W
3/4”
80.0
50-FLATWORK ACCESSORIES
2-STRUT WITH FERRULE LF-W
30-ATLAS TECH PRODUCTS
Type
10-FORMING & SHORING
TYPE L INSERTS
Wt. Lbs. per 100
Open end Ferrule available Available in Stainless Steel and electro-galvanized
NC THREADS Special Order Thread Type
3/8”
16 NC
Product Code No.
Wt. Lbs. per 100
1/2”
13 NC
1.1
5/8”
11 NC
1.8
3/4”
10 NC
3.3
1”
8 NC
7.6
PRODUCTS
0.9
70- FOUNDATION
Dia.
F-72
60-PRECAST & TILT-UP
THREADED STEEL SETTING PLUGS
80- TOOLS & PLACING
www.atlasform.com
83
F-73
30-ATLAS TECH PRODUCTS
FERRULE INSTEAD OF A COIL Bolt Dia.
Wt. Lbs.
1/2”
7.5 per 100 ferrules
5/8”
15.0 per 100 ferrules
3/4”
18.5 per 100 ferrules
7/8”
40.0 per 100 ferrules
1”
39.0 per 100 ferrules
1-1/4”
75.0 per 100 ferrules
Ferrules with closed bottom and National Coarse Threads can be supplied instead of a coil.
F-74
THREADED PLASTIC PLUG NC THREADS
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
Contractor Committed.
Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
FORMING ACCESSORIES
F-105
Size
Thread Type
Product Code No.
Wt. Lbs. per 100
3/8”
16 NC
20.28.21010
0.5
1/2”
13 NC
20.28.21020
0.6
5/8”
11 NC
20.28.21030
0.8
3/4”
10 NC
20.28.21040
1.0
7/8”
9 NC
20.28.21050
1.7
1”
8 NC
20.28.21060
2.0
TYPE B-4 CUSHION-LOCK REGLET Special Order Product Code No.
Wt. Lbs. 37.0 per box
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Available only in full boxes of 200 ft. in 10 ft. lengths. Each box of Type B-4 Reglet includes 24 connector plugs and installation instructions with template pattern. Cushion-Lock Reglets are protected by U.S. Patent Numbers 3,241,271 - 3,246,433 - 3,319,384- 3,981,108 - 3,974,619.
84
www.atlasform.com
Serving Concrete Customers Since 1980.
FORMING ACCESSORIES
H-3
Slot Size
Type
Gauge
7/16”
A
16 ga. Galv.
Product Code No.
Wt. Lbs. per 100 12.8
3/16”
B
16 ga. Galv
13.1
10-FORMING & SHORING
BEAM CLIP Special Order
Available only in full cartons of 500 pieces
FOR PLYWOOD FORMS Size
Product Code No.
Wt. Lbs. Per Carton
Packaging
20.28.10010
4.0
1,000 per carton
20.28.10020
7.0
1,000 per carton
H-6
FORM PATCH Product Code No.
Wt. Lbs. Per Carton
Packaging
20.28.11175
20.0
1,000 per carton
2-1/4” dia. Galv. Stock
20.28.11225
27.0
1,000 per carton
2-3/4” dia. Galv. Stock
20.28.11275
33.0
1,000 per carton
40-BAR SUPPORTS
Size & Type 1-3/4” dia. Galv. Stock
30-ATLAS TECH PRODUCTS
9/16” 13/16”
20-FORMING ACCESSORIES
H-5
PLASTIC PLUG
Available only in full cartons
50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
85
Contractor Committed.
Quality Proven Performance Consistent Service Availability Technical Support Trust
Quality Concrete Construction Chemicals & Restoration Products
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Concrete Chemicals, Epoxies & Cementitious Materials
PRODUCTS
Form Release Agents Curing Compounds Concrete Sealers Bondbreakers for Tilt-Up Liquid Bonding Agents Epoxy Bonding Agents Epoxy Injection Resins Grouts Patching & Repair Mortars overlays & deck sealers Self-Leveling Underlayments Shake-on Floor Hardeners All Atlas Tech Products are conveniently stocked at all Atlas Construction Supply locations!
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
• • • • • • • • • • • •
Treat your concrete to Tech Products. 86
www.atlasform.com
Form Release Agents
Serving Concrete Customers Since 1980.
Chemically Reactive Form Release Agent
Description
Features of Atlas Release
Coverage Untreated Plywood: 700 - 1,200 ft2 per gal. BB Grade Plyform: 1,200 ft2 per gal. MDO: 1,200 - 1,500 ft2 per gal. HDO: 2,000 ft2 per gal. Steel, Aluminum, Fiberglass: 2,000 - 2,500 ft2 per gal. Atlas Fog Spray Tip This valuable spray tip increases coverage rates up to 400% over standard fan-type spray tips. Saves material costs and produces a great concrete finish! Packaging
Product Code
5 gallon pails
30.10.10025
55 gallon drums
30.10.10035
275 gallon totes
30.10.10045
60-PRECAST & TILT-UP PRODUCTS
80- TOOLS & PLACING
Competitor Release
www.atlasform.com
70- FOUNDATION
Atlas Release
Corps of Engineers CEGS 03300 Section 10.8 Navy Dock and Piers 56359 VOC Compliant
50-FLATWORK ACCESSORIES
• Provides a quick and easy release of concrete forms. • Will not stain or discolor concrete surfaces. • Produces a smooth concrete surface with minimal to no bugholes or surface dusting. • Excellent for exposed architectural concrete, and cost effective for all concrete forming applications. • Significantly reduces form clean-up time between pours. • Contains a wood preservative to provide at least twice the form life of untreated wood. • Contains rust inhibitors to protect steel forms. • Leaves no residue on concrete. Will not affect the adhesion of curing compounds, sealers, paints, caulking or other architectural treatments. • Easy to work with, pleasant scent. • Does not contain diesel oil, kerosene, waxes, silicones or carcinogenic compounds. • Once dry, it will not wash-off if exposed to light rain. • Can be applied in subfreezing or extremely hot temperatures.
Technical Data & Specifications
40-BAR SUPPORTS
• May be used on many types of concrete forms, such as wood, steel, aluminum, fiberglass, plastic, paper, epoxy or urethane coated molds, masonite and formliners. • Treat wood and steel forms to increase the useable life of form surfaces. • Spray on equipment such as mixers, pavers, trucks, finishing machines, etc. for easy clean-up and maintenance.
Atlas Release used for over 500,000 sq. ft. of architectural walls on the Cathedral of Our Lady of the Angels in Los Angeles, CA.
30-ATLAS TECH PRODUCTS
Uses
20-FORMING ACCESSORIES
Atlas Release is an extremely effective, chemically reactive form release agent that prevents concrete from bonding to formwork and leaves clean, smooth, hard and consistent concrete surfaces. The organic compounds in Atlas Release react with the alkali content of concrete to produce a slick release and allow for quick and easy removal of concrete formwork. The resulting concrete surface is stain-free and ready to accept curing compounds, sealers, paint or other architectural treatments.
10-FORMING & SHORING
The best value form release agent anywhere!
ATLAS RELEASE
87
Contractor Committed.
ATLAS BIO-GUARD Water-Based, Biodegradable Form Release Agent
Description Atlas Bio-Guard is a premium, environmentally safe, chemically reactive form release agent for use on many different types of concrete forms. A natural emulsified organic vegetable oil, Bio-Guard is biodegradable and is ideal for use in environmentally sensitive areas, concrete precast plants, or wherever architectural concrete surfaces are required. Bio-Guard provides easy form stripping, produces concrete surfaces that are stain-free, smooth & non-dusting, and minimizes form clean-up time and maintenance costs.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Form Release Agents
Uses • Ideal for environmentally sensitive projects, such as bridge work over rivers & streams, potable water reservoirs, or jobsites where spillage or run-off is a concern. • May be used on many types of concrete forms for architectural concrete, such as wood, steel, aluminum, fiberglass, plastic, paper, epoxy or urethane coated molds, masonite, formliners and expanded polystyrene. • Excellent with most elastomeric and PVC formliners. • Spray on equipment such as mixers, pavers, finishing machines, etc. for easy clean-up and maintenance.
Features of Atlas Bio-Guard • 100% natural organic chemical release agent that is biodegradable and environmentally safe. • Reduces risk of expensive clean-up. • Non-staining release for architectural concrete. • Helps prevent bugholes and surface dusting. • Leaves no residue on concrete after forms are stripped. • Easy to work with, odorless. Does not contain diesel oil, kerosene, waxes, silicones or carcinogenic compounds. • Once dry, it will not wash-off if exposed to light rain. • GreenSpec® Listed for LEED® projects and certified to meet NSF/ANSI Std. 61 requirements for potable water projects.
Coverage Untreated Plywood: 500 - 1,000 ft2 per gal. MDO: 1,000 - 1,200 ft2 per gal. HDO: 1,500 ft2 per gal. Steel, Aluminum, Fiberglass: 1,500 - 2,000 ft2 per gal. Atlas Bio-Guard performs with urethane formliners! Read Product Data Sheet and MSDS prior to use.
ATLAS PREMIUM GOLD RELEASE
Product Code 30.10.11025
55 gallon drums
30.10.11035
275 gallon totes
30.10.11045
Features of Atlas Premium Gold Release
Chemically Reactive Form Release Agent For Architectural Concrete
Description Atlas Premium Gold Release is a high performance, chemically reactive form release agent that is ideal for high visual impact precast and architectural concrete. Premium Gold Release provides easy removal of many types of concrete forms and leaves a stain-free concrete surface that is smooth, hard, and ready to accept further treatments. Premium Gold Release produces beautiful clean concrete surfaces and helps eliminate bugholes & surface dusting.
Uses • Ideal for high visual impact precast and architectural concrete. • May be used on many types of concrete forms, such as wood, steel, aluminum, fiberglass, plastic, paper, epoxy or urethane coated molds, masonite and formliners. • Compatible with most elastomeric and PVC formliners. • Treat wood and steel forms to increase the useable life of form surfaces.
88
Packaging 5 gallon pails
• Will produce a smooth, clean and stain-free concrete surface for architectural and precast concrete. • Reduces form clean-up time and cost by more than 50%. • Contains a wood preservative that increases life of wood formwork - Prevents forms from absorbing the alkali water in the concrete to keep forms smooth, hard and intact. • Safeguards steel forms to allow for easy cleaning and protection of form faces in between pours. • Unequaled for preventing bugholes and surface dusting on the concrete surface. • Leaves no residue on concrete. Will not affect the adhesion of curing compounds, sealers, paints, etc.
Coverage Untreated Plywood: 800 - 1,200 ft2 per gal. MDO: 1,500 - 2,000 ft2 per gal. HDO: 2,500 ft2 per gal. Steel, Aluminum, Fiberglass: 2,500 - 3,000 ft2 per gal. Packaging
Product Code
5 gallon pails
30.10.10525
55 gallon drums
30.10.10535
275 gallon totes
30.10.10545
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
Concrete Curing Compounds
Serving Concrete Customers Since 1980.
This cure belongs on every concrete job! 10-FORMING & SHORING
ATLAS QUANTUM CURETM Non-Staining, Membrane-Forming Concrete Curing Compound that is Compatible with Subsequent Concrete Treatments & Flooring.
Description
Atlas Quantum-CureTM used on exposed walls and walls to be covered at the Griffith Park Observatory in Los Angeles, CA.
Coverage Broom Finish: 200 - 400 ft2 per gal. Smooth Finish: 400 - 600 ft2 per gal. Vertical Surface: 400 - 500 ft2 per gal. Packaging
Product Code
Product Code
5 gallon pails
30.11.11025
30.11.11125
55 gallon drums
30.11.11035
30.11.11135
275 gallon totes
30.11.11045
40-BAR SUPPORTS
• Concrete floors, decks, walls, columns, beams, sidewalks, driveways, architectural concrete, etc. • Interior and exterior applications. • Ideal for schools, hospitals, condominiums, office buildings, parking garages, warehouses, manufacturing facilities, food processing plants, stadiums, house foundations, etc. • Certified to meet NSF/ANSI Standard 61 requirements for potable water projects, and GreenSpec® listed for LEED® projects.
30-ATLAS TECH PRODUCTS
Uses
20-FORMING ACCESSORIES
Atlas Quantum-CureTM is a clear, water-based concrete curing compound that is formulated to ensure proper concrete strength development, prevent shrinkage cracks, and leave a bondable surface for further coatings, treatments or flooring. This ready-to-use, non-staining, membrane-forming cure is formulated to control moisture retention in freshly placed concrete for proper cement hydration. Quantum-CureTM does not need to be removed prior to the application of subsequent sealers, paints, adhesives, flooring materials, waterproofing, etc. Quantum-CureTM provides contractors, architects, engineers and owners a simple solution to compatibility and discoloration issues. Certified to meet NSF/ANSI Standard 61 requirements for potable water projects.
Moisture Loss ( kg / sq. M)
89
80- TOOLS & PLACING
www.atlasform.com
PRODUCTS
ASTM C-309 .55 kg / sq. M
70- FOUNDATION
Moisture Loss
Read Product Data Sheet & MSDS prior to use.
60-PRECAST & TILT-UP
• Membrane-forming to control moisture retention for proper cement hydration. • Helps concrete reach maximum strength. • Helps prevent plastic shrinkage cracks. • Compatible with subsequent treatments, coatings and flooring, such as Atlas Tech sealers, paints, waterproofing, tile, carpet adhesives, cement-based The chart below shows the comparison of Atlas Quantum-CureTM with mortars, or other architectural coatings. other types of concrete curing compounds. Atlas Quantum-CureTM has • Non-staining formulation similiar moisture retention of resin cures, but offers the important benefits maintains natural look of of non-staining & compatibility with subsequent concrete treatments. concrete. • Increases abrasion and Moisture Loss of Concrete Curing Compounds impact resistance of (Applied @ 200 sq. ft. / gal.; measured 72 hours after application) concrete surface. 1.80 • Water-based formulation; 1.60 meets most stringent VOC regulations. 1.40 • Fast drying. 1.20 • Will not yellow, even if 1.00 exposed to sunlight. • Does not contain any waxes, 0.80 silicones or paraffins. 0.60 • Does not contain any 0.40 flammable or combustible solvents. 0.20 • Pleasant scent. 0.00 • Ready-to-use and easy to Acrylic Resin Acrylic Acrylic Resin QuantumSodium spray; no clogged sprayers. 30% White Pig. 19% 14% Cure Silicate • Easily clean equipment with Curing Compound water after use.
50-FLATWORK ACCESSORIES
Features of Atlas Quantum-CureTM
Contractor Committed.
ATLAS RES-CURE
Features of Atlas Res-Cure
Clear, Water-Based, Dissipating Resin Curing Compound
Description
Atlas Res-Cure is available in many DOT approved formulations, including Caltrans, Nevada, Arizona and Colorado. Ask your Atlas representative for further information.
White Pigmented, Water-Based, Resin Curing Compound
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
30-ATLAS TECH PRODUCTS
Atlas Res-Cure is an emulsified resin curing compound for use on interior, exterior, horizontal and vertical concrete surfaces. This ready-to-use membrane-forming cure is formulated to control moisture retention in freshly placed concrete for proper cement hydration. Res-Cure provides excellent early curing properties and will begin to dissipate approximately 28 - 40 days after application. Once the resin is completely dissipated, the concrete surface is suitable for application of subsequent sealers, paints, adhesives, flooring materials, waterproofing, etc.
40-BAR SUPPORTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Concrete Curing Compounds
ATLAS RES-CURE WHITE
PRODUCTS
70- FOUNDATION
Technical Data & Specifications ASTM C-309, Type 1 & 1D, Class A & B AASHTO M-148, Type 1 & 1D, Class A & B VOC Compliant Packaging Typical coverage rate: 5 gallon pails 200 ft2 per gal.
Description Atlas Res-Cure White is a white-pigmented, emulsified resin curing compound for use on exterior, horizontal and vertical concrete surfaces. This ready-to-use membraneforming cure is formulated to control moisture retention in freshly placed concrete for proper cement hydration. Res-Cure White provides excellent early curing properties; the white pigment keeps the concrete surface cooler and helps prevent thermal cracking. Ideal for concrete highways, airport runways, bridges, street & curb paving, sidewalks, canals, dams, etc. Atlas Res-Cure White is available in many DOT approved formulations, including Caltrans, Nevada, Arizona and Colorado. Ask your Atlas representative for further information.
ATLAS CLEAR CURE WAX Description Atlas Clear Cure Wax is a water emulsified wax curing compound for freshly poured concrete surfaces. This high solids formulation controls water retention during the curing period to help produce strong and durable concrete and help prevent plastic shrinkage cracks & surface dusting. Atlas Clear Cure Wax is ideal for concrete highways, airport runways, residential paving, canals, dams, etc. Atlas Clear Cure Wax is available in many DOT approved formulations, including Caltrans, Nevada, Arizona and Colorado. Ask your Atlas representative for further information.
90
30.11.11525
55 gallon drums
30.11.11535
275 gallon totes
30.11.11545
• White pigmentation keeps concrete surfaces cooler and helps prevent thermal cracking. • Membrane-forming to control moisture retention for proper cement hydration. • Helps produce harder and more dense concrete surfaces while increasing resistance to cracking, dusting, and chemical attack. • Ready-to-use and easy to spray-apply. • Water-based formulation; meets most stringent VOC regulations. • Fast drying. • Low odor.
Technical Data & Specifications ASTM C-309, Type 2, Class A & B AASHTO M-148, Type 2, Class A & B VOC Compliant Packaging Typical coverage rate: 5 gallon pails 2 200 ft per gal.
Read Product Data Sheet & MSDS prior to use.
Read Product Data Sheet & MSDS prior to use.
Product Code
Features of Atlas Res-Cure White
Clear, Water-Based, Wax Curing Compound
80- TOOLS & PLACING
• Membrane-forming to control moisture retention for proper cement hydration. • Ready-to-use and easy to spray-apply. • After film dissipates, concrete surface is suitable for application of subsequent treatments and flooring. • Water-based formulation; meets most stringent VOC regulations. • Fast drying. • Low odor. • Available with a red fugitive dye for ease of application.
Product Code 30.11.12025
55 gallon drums
30.11.12035
275 gallon totes
30.11.12045
Features of Atlas Clear Cure Wax • Membrane-forming to control moisture retention for proper cement hydration. • Ready-to-use and easy to spray-apply. • Economical, low odor, fast drying, & dries clear.
Technical Data & Specifications ASTM C-309, Type 1 & 1D, Class A AASHTO M-148, Type 1 & 1D, Class A VOC Compliant Typical coverage rate: 200 ft2 per gal. Packaging
Product Code
5 gallon pails 55 gallon drums 275 gallon totes
www.atlasform.com
30.11.12535
Concrete Curing Compounds
Serving Concrete Customers Since 1980.
White Pigmented, Water-Based, Wax Curing Compound
Description
Read Product Data Sheet & MSDS prior to use.
ATLAS CURE & HARD Description
Read Product Data Sheet & MSDS prior to use.
Packaging
Product Code
5 gallon pails
30.11.13025
55 gallon drums
30.11.13035
275 gallon totes
30.11.13045
Features of Atlas Cure & Hard • Retains natural look of concrete. • Compatible with subsequent treatments and coatings. • Water-based formulation; meets most stringent VOC regulations. • Economical.
Technical Data & Specifications USDA Approved VOC Compliant Typical coverage rate: 200 ft2 per gal. Packaging
Product Code
5 gallon pails
30.11.14025
55 gallon drums
30.11.14035
50-FLATWORK ACCESSORIES
Atlas Cure & Hard is a clear, odorless, water-based, general purpose concrete curing compound. This economical cure is a reactive blend of silicates that will penetrate the concrete surface to provide adequate hydration, prevent surface dusting, and increase the density of the concrete. Cure & Hard leaves no residue on the concrete and provides a bondable surface for subsequent treatments and coatings.
ASTM C-309, Type 2, Class A AASHTO M-148, Type 2, Class A VOC Compliant Typical coverage rate: 200 ft2 per gal.
40-BAR SUPPORTS
Clear, Penetrating, Water-Based Curing Compound
Technical Data & Specifications
30-ATLAS TECH PRODUCTS
Atlas Whix Cure is available in many DOT approved formulations, including Caltrans, Nevada, Arizona and Colorado. Ask your Atlas representative for further information.
• White pigmentation keeps concrete surfaces cooler and helps prevent thermal cracking. • Membrane-forming to control moisture retention for proper cement hydration. • Helps produce harder and more dense concrete surfaces while increasing resistance to cracking, dusting, and chemical attack. • Ready-to-use and easy to spray-apply. • Water-based formulation; meets most stringent VOC regulations. • Fast drying & low odor.
275 gallon totes
ATLAS FINISH-FILM Evaporation Reducer & Finishing Aid
Read Product Data Sheet & MSDS prior to use. Packaging
Product Code
5 gallon pails
30.11.16025
55 gallon drums
30.11.16035
80- TOOLS & PLACING
• During finishing of concrete flatwork when rapid-drying conditions exist (high ambient temperatures, high winds, direct sunlight, low humidity, low water-cement ratio concrete mixes). • May be used with shake-on floor hardeners and toppings, cementitious patches & repair mortars. • Interior and exterior applications.
PRODUCTS
Uses
• Significantly reduces surface moisture evaporation to extend and facilitate the finishing process during hot, dry or windy conditions. • Reduces or even eliminates plastic shrinkage cracking. • Reduces wind crusting and stickiness, allowing for easier troweling. • Promotes higher-strength, lower slump concrete by allowing lower slump mixes without the need for additional mix water to resist rapid evaporation. • Allows for proper and easier finishing of dry-shake floor hardeners. • Does not inhibit the performance or bond of curing compounds, sealers or other treatments to be applied to the concrete surface at a later time. • Does not change the final color of the concrete surface. • Increases productivity; each finisher can properly finish a larger area. • Water-based formulation; no odor.
Technical Data & Specifications VOC Compliant As recommended by ACI 302: Evaporation Retardant / Monomolecular Film Typical Coverage: 100 - 300 ft2 per gal.
www.atlasform.com
70- FOUNDATION
Atlas Finish-Film is a water-based evaporation retarder for use on freshly placed concrete flatwork. Finish-Film produces a monomolecular film on the concrete surface to prevent rapid moisture loss and allow for proper finishing. Finish-Film is especially beneficial during rapid-drying conditions and will help prevent plastic shrinkage cracking.
Features of Atlas Finish-Film 60-PRECAST & TILT-UP
Description
20-FORMING ACCESSORIES
Atlas Whix Cure is a water emulsified white wax curing compound for application on freshly placed concrete surfaces. Atlas Whix Cure forms a vapor sealing membrane to control moisture retention and produce strong and durable concrete. The white pigmentation in Atlas Whix Cure provides good reflective protection for exterior concrete which is important for applications that are subject to high temperatures caused by exposure to direct sunlight. Ideal for concrete highways, airport runways, bridges, street & curb paving, sidewalks, canals, dams, etc.
Features of Atlas Whix Cure 10-FORMING & SHORING
ATLAS WHIX CURE
91
Contractor Committed.
ATLAS CURE & SEAL 14% Clear, Water-Based, Acrylic Cure & Seal
Features of Atlas Cure & Seal-14%
Description Atlas Cure & Seal-14% is a water-based, acrylic copolymer solution that provides concrete with both an excellent cure and seal of the concrete surface. Cure & Seal-14% forms a clear membrane on the concrete surface to retain the necessary moisture in freshly placed concrete for proper strength development and help prevent plastic shrinkage cracks & dusting. This multi-funtional product provides a low to medium sheen finish on the surface and helps resist staining and penetration of mild chemicals, oils, salts and other contaminants. Packaging
Product Code
5 gallon pails
30.12.10025
55 gallon drums
30.12.10035
275 gallon totes
30.12.10045
• Cure, seal, harden and dustproof concrete surfaces in one application. • Produces a tough membrane on concrete surface for efficient moisture retention during curing period. • Minimizes plastic shrinkage cracks, dusting & spalling. • Protects surface from staining and penetration of mild chemicals, oils, salts and other contaminants. • Dries clear and provides a sheen finish that enhances the natural look of concrete. • May be used for most colored concrete applications.
Technical Data & Specifications ASTM C-309, Type 1 & 1D, Class A & B AASHTO M-148, Type 1 NAVDOCK 13 YF VOC Compliant Typical Coverage: 200 - 400 ft2 per gal.
Read Product Data Sheet & MSDS prior to use.
ATLAS CURE & SEAL 30% Clear, Water-Based, High Solids Acrylic Cure & Seal
Features of Atlas Cure & Seal-30%
Description Atlas Cure & Seal-30% is a water-based, acrylic copolymer solution that provides concrete with both an excellent cure and seal of the concrete surface. Cure & Seal-30% forms a clear membrane on the concrete surface to retain the necessary moisture in freshly placed concrete for proper strength development and help prevent plastic shrinkage cracks & dusting. This multifuntional product provides a high sheen finish on the surface and helps resist staining and penetration of mild chemicals, oils, salts and other contaminants. Packaging
Product Code
5 gallon pails
30.12.11025
55 gallon drums
30.12.11035
275 gallon totes
30.12.11045
• Cure, seal, harden and dustproof concrete surfaces. • Produces a tough membrane on concrete surface for efficient moisture retention during curing period. • Minimizes plastic shrinkage cracks, dusting & spalling. • Protects surface from staining and penetration of mild chemicals, oils, salts and other contaminants. • Dries clear and provides a sheen finish that enhances the natural look of concrete.
Technical Data & Specifications ASTM C-309, Type 1 & 1D, Class A & B AASHTO M-148, Type 1, NAVDOCK 13 YF ASTM C-1315, Type 1, Class A & B VOC Compliant Typical Coverage: 200 - 400 ft2 per gal.
PRODUCTS
Read Product Data Sheet & MSDS prior to use.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Concrete Curing & Sealing Compounds
92
www.atlasform.com
Serving Concrete Customers Since 1980.
Concrete Curing & Sealing Compounds
ATLAS EASY SEAL
Features of Atlas Easy-Seal
Description
Uses
ASTM C-309, Type 1, Class A & B AASHTO M-148, Type 1 VOC Compliant
Broom Finish: 200 - 400 ft2 per gal. Smooth Finish: 300 - 500 ft2 per gal. Tilt-up Casting Slab: 400 - 600 ft2 per gal. Packaging
Product Code
5 gallon pails
30.12.11525
55 gallon drums
30.12.11535
275 gallon totes Atlas Easy-Seal is compatible with Atlas bondbreakers for Tilt-Up construction!...Atlas provides complete product systems to save contractors $$$ & liability, while providing a better finished product!
Read Product Data Sheet & MSDS prior to use.
Features of Atlas Tech-1315
Read Product Data Sheet & MSDS prior to use.
ASTM C-1315, Type 1, Class A & B ASTM C-309, Type 1 & 1D, Class A & B Federal Specification TT-C-800A USDA Approved, VOC Compliant
Coverage Broom Finish: 200 - 400 ft2 per gal. Smooth Finish: 300 - 500 ft2 per gal.
www.atlasform.com
Packaging
Product Code
5 gallon pails
30.12.12025
55 gallon drums
30.12.12035
275 gallon totes
30.12.12045
93
80- TOOLS & PLACING
• Cure, seal, harden & dustproof freshly placed concrete or seal, harden & dustproof aged concrete surfaces. • Interior, exterior, horizontal and vertical applications. • Seal and enhance the appearance of aged concrete, terrazzo, brick and masonry. • Ideal for exposed columns, beams & walls, commercial & industrial floors, food processing plants, maintenance facilities, factories, parking structures, office buildings, driveways, sidewalks, architectural concrete, etc.
PRODUCTS
Technical Data & Specifications
70- FOUNDATION
Uses
Description
60-PRECAST & TILT-UP
Atlas Tech-1315 is a high-performance, water-based, acrylic concrete cure, sealer, hardener and dustproofer. This easy-to-use product is ultraviolet resistant and meets the demanding ASTM C-1315 specification for moisture retention and color stability when applied to freshly placed concrete. Tech-1315 produces a protective film on the concrete surface to help concrete reach its maximum strength and hardness and to improve resistance to harsh weather conditions, most acids & chemicals, oils, salts and other contaminants. Tech-1315 dries to a clear, medium sheen finish that will enhance the natural appearance of concrete, brick, decorative stone and exposed aggregate.
• Meets ASTM C-1315 specification. Excellent curing properties and UV resistance. • Cure, seal, harden and dustproof concrete surfaces in one application. • Produces a tough membrane on concrete surface for excellent moisture retention during curing period. • Minimizes plastic shrinkage cracks, dusting & spalling. • Increases durability and abrasion resistance of concrete. • Protects surface from staining and penetration of most acids, chemicals, alkalis, oils and other contaminants. • Dries clear and provides a medium sheen finish that enhances the natural look of the treated surface. • Excellent for interior or exterior applications; UV resistant. • Helps prevent efflorescence. • Fast drying. • Ready-to-use and easy to apply. • Reduces cleaning and maintenance for occupant.
Clear, Water-Based, High Solids Acrylic Cure & Seal Meeting ASTM C-1315
50-FLATWORK ACCESSORIES
ATLAS TECH-1315
40-BAR SUPPORTS
Technical Data & Specifications
Coverage
30-ATLAS TECH PRODUCTS
• Cure, seal, harden & dustproof freshly placed concrete surfaces or seal, harden & dustproof aged concrete. • Exposed columns, beams & walls, commercial & industrial floors, parking structures, office buildings, driveways, sidewalks, architectural concrete, etc. • Ideal for tilt-up casting slabs prior to the application of a bondbreaker. • Interior, exterior, horizontal and vertical applications.
20-FORMING ACCESSORIES
Atlas Easy-Seal is a clear acrylic concrete curing and sealing compound that helps provide proper strength development and a protective seal for concrete surfaces. Easy-Seal has been formulated with premium materials to produce a fast-drying, non-yellowing, membrane-forming product that meets ASTM C-309 curing standards and provide a durable finish for increased protection from chemicals, oils, chlorides and stains.
• Provides a one-application cure, sealer, hardener and dustproofer for many applications. • Meets ASTM C-309 curing specification and is compatible with Atlas Easy-Lift bondbreakers. • Rapid-drying to allow traffic on treated surface in a minimal amount of time. • Helps provide a strong concrete surface while minimizing shrinkage cracks, spalling, and dusting. • Produces a clear sheen surface finish that will not yellow, even when exposed to ultraviolet rays. • Increases protection from chemical attack and stains from oils, grease and other contaminants. • Minimizes clean-up time and costs. Sealed concrete surface is easy to clean and maintain. • Helps prevent efflorescence. • Safe and easy to use for exterior or interior applications; very low odor.
10-FORMING & SHORING
Clear, Water-Based, Acrylic Cure & Seal
20-FORMING ACCESSORIES
10-FORMING & SHORING
Concrete Curing & Sealing Compounds
Contractor Committed.
ATLAS EXPO SEALTM Clear, High Gloss, Durable, Laquer-Based, Acrylic Cure & Seal
Description Atlas Expo-SealTM is a high performance concrete curing & sealing compound that provides a tough and clear protective coating over exposed concrete surfaces. Expo-SealTM is a unique acrylic co-polymer formulation that will help prevent shrinkage cracks and produce a concrete surface with maximum strength and increased resistance to traffic, moisture and stains. Expo-SealTM is ultraviolet resistant and provides an attractive finish to architectural concrete. This durable concrete treatment enhances the beauty of colored concrete, exposed aggregate and stone.
30-ATLAS TECH PRODUCTS
ASTM C-1315, Type 1, Class A & B VOC Compliant Typical Coverage: 200 - 300 ft2 per gal.
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
• Cure, seal, harden and dustproof concrete surfaces. • Interior, exterior, horizontal and vertical exposed concrete surfaces. • Areas subjected to heavy walking or vehicle traffic. • Protect and enhance the appearance of existing concrete, exposed aggregate, colored concrete, stone, brick, tile, stucco, plaster, etc. • Ideal for shopping plazas, hotels, schools, stadiums, lobbies, residences, driveways, garages, patios, barbeque areas, or any concrete surface where a high gloss, protective coating is desired.
Features of Atlas Expo-SealTM • Meets demanding ASTM C-1315 specification; excellent curing properties and UV resistance. • Protects, dustproofs and enhances the appearance of concrete, exposed aggregate, brick, masonry and stucco surfaces. • Excellent resistance to high walking traffic and wear. • Good chemical and stain resistance. • Excellent weather and corrosion resistance. • Provides an attractive “wet-look” finish. • Excellent for interior or exterior applications • Provides an easy to clean surface. • Durable film keeps exposed aggregate from popping-out. • May be used for most colored concrete applications. • Helps prevent efflorescence. • Fast-drying. • Ready-to-use and easy to apply. • Consistent and uniform results.
Technical Data & Specifications
Atlas Expo-SealTM is ideal for application on exposed aggregate & decorative concrete to provide excellent protection and a “wet-look” finish. Read Product Data Sheet & MSDS prior to use.
Packaging
Product Code
1 gallon pails
30.12.12520
5 gallon pails
30.12.12525
ATLAS OUTSHINE SEALER Clear, Water-Based, High Solids Acrylic Sealer
Features of Atlas Out-Shine Sealer
Description
• Seals, protects, dustproofs and enhances the appearance of concrete, exposed aggregate, brick, masonry and stucco surfaces. • Increases durability and abrasion resistance of concrete. • Good chemical and stain resistance. • Provides an attractive gloss finish. • Excellent for exterior applications; UV resistant. • Helps prevent efflorescence. • Durable film prevents aggregate from popping out. • Provides an easy to clean surface. • Low odor, pleasant to use indoors. • May be used for most colored concrete applications.
Atlas Out-Shine Sealer is a heavy-duty, clear, waterbased liquid sealer and dustproofer that is designed to protect and enhance the appearance of exterior or interior concrete, exposed aggregate, brick, masonry and stucco surfaces. This innovative synthetic polymer formulation provides superior surface protection with excellent abrasion resistance in areas of high traffic, resistance to penetration and staining of mild chemicals and acids, and resistance to weathering and corrosion. Out-Shine Sealer is a high-solids product that produces a gloss finish that will not discolor when exposed to sunlight.
Technical Data & Specifications
Uses 80- TOOLS & PLACING
Uses
• Seal and protect concrete, exposed aggregate, brick, masonry and stucco surfaces. • Exterior and interior applications. • Horizontal and vertical applications. • Ideal for shopping plazas, schools, hospitals, factories, stadiums, walkways, patios, swimming pool decks, terrazzo floors, masonry walls, etc.
94
VOC Compliant Typical Coverage: 200 - 300 ft2 per gal. Packaging
Product Code
5 gallon pails
30.12.13025
55 gallon drums
30.12.13035
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
Concrete Curing & Sealing Compounds
Serving Concrete Customers Since 1980.
10-FORMING & SHORING
ATLAS ELITE HSTM
High Performance, Clear, Water-Based, Penetrating Concrete Hardener, Sealer & Dustproofer
Description
SEALER HARDENER DUSTPROOFER
Features of Atlas Elite-HSTM
Maintenance
Warranty
Packaging
Product Code
5 gallon pails
30.12.13525
55 gallon drums
30.12.13535
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
95
80- TOOLS & PLACING
Atlas provides a 20 year anti-dusting guarantee against the effects of wear and abrasion for floors treated with Elite-HSTM. Contact your local Atlas representative for details.
PRODUCTS
Elite-HSTM develops a low-gloss, integral shine that will last the lifetime of the concrete. The more traffic the concrete gets, the better it will look! For an immediate shine, a floor buffer may be used. Treated concrete surfaces are easily cleaned with a mop and warm, soapy water or a scrubbing machine.
70- FOUNDATION
USDA Approved VOC Compliant Typical Coverage: 200 -400 ft2 per gal.
60-PRECAST & TILT-UP
Technical Data & Specifications
50-FLATWORK ACCESSORIES
• Seals, densifies, hardens and dustproofs concrete and masonry surfaces in one application. • Produces a low-gloss, integral satin sheen finish that will not wear-away. • Treated concrete floors are more resistant to abrasion and wear from vehicles, forklifts, pallets, heavy walking traffic, etc. • Prevents concrete floors from dusting to protect personnel and stored materials from exposure to concrete dust. • Reduces surface porosity, helping to protect concrete from stains, spills, oils and chemical attack. • Resists black tire marks on floors. • Will not peel, scratch, blister or discolor; outlasts floor coatings. • Breathable sealer for both interior or exterior use. • Provides an easy to clean and maintain surface. • Safe and easy to use; no mixing, etching or expensive equipment needed. • Enhances the performance and look of concrete floors treated with dry-shake floor hardeners. • Environmentally safe. • No harmful fumes or odors; pleasant to use indoors. • Water-based formulation; meets most stringent VOC regulations. • Develops a more polished look with age and wear. • Long-term warranty available.
40-BAR SUPPORTS
• Ideal for warehouses, distribution centers, industrial plants, factories, food processing plants, maintenance facilities, schools, hospitals, shopping centers, retail floors, showrooms, restaurants, parking structures, garages, airports, stadiums, etc. • Interior and exterior applications. • New and aged concrete and masonry applications.
Atlas Elite-HSTM is easily applied to concrete surfaces with brooms, squeegees or buffing machines to provide a very durable concrete floor with an attractive low-gloss sheen finish that is easy to clean and maintain.
30-ATLAS TECH PRODUCTS
Uses
20-FORMING ACCESSORIES
Atlas Elite-HSTM is a colorless, odorless, penetrating, water-based, siliconate solution formulated to seal, densify, harden and dustproof concrete and masonry surfaces. Elite-HSTM uses a chemical reaction to fill the pores in concrete, therefore increasing the abrasion resistance and durability of the concrete and reducing the porosity of the treated surface. This concrete treatment will protect the most abused floors from traffic and wear, and increase resistance to chemicals, water, stains and black tire marks. Elite-HSTM protects, preserves and strengthens concrete and masonry surfaces while providing a permanent lowgloss satin sheen finish that is very easy to clean and maintain.
Contractor Committed.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Bondbreakers for Tilt-up & Precast
ATLAS EASY-LIFT FDTM Premium, Fast-Drying, Water-Based Cure & Bond Breaker for Tilt-Up & Precast
Description Atlas Easy-Lift FDTM is a high-performance, chemically reactive, water-based, fast drying cure and bondbreaker for tilt-up and precast construction. Easy-Lift FDTM is applied to the concrete casting slab to efficiently prevent the bonding of subsequent concrete pours. This premium-grade bondbreaker contains organic compounds that react with the concrete to produce a water impermeable barrier on the surface of the casting slab. When the tilt-up panel is poured, the barrier restricts the casting slab from absorbing the mix water from the panel, resulting in an easy to lift panel and a strong, smooth, uniform and clean panel appearance. This fast drying formulation allows crews to complete work more quickly and produces cleaner panels by reducing occurrence of dirt accumulation on the casting slab. Easy-Lift FDTM meets all VOC regulations.
Features Of Atlas Easy-Lift FDTM • Provides an easier lift of tilt-up panels than other bondbreakers. • Fast-drying formulation allows crews to get on slab earlier to form panels and place reinforcing steel. Also minimizes accumulation of dirt and dust on casting surface, resulting in cleaner panels. • Chemically reactive formulation minimizes “osmoticeffect”; panel surface will be stronger and have a more uniform and clean appearance. • Strong, smooth, uniform and clean panels result in minimal sacking/patching costs. • Easy to apply; no back-rolling required. • Rain resistant after coats dry. • Resists construction foot traffic during placement of reinforcing steel. • Does not contain waxes, resins or silicones. • Will not impair the adhesion of paints or coatings after the panels have been lifted and placed, when applied according to manufacturer’s application instructions. • Safe and easy to use; low odor. • Economical bondbreaker system; exhibits greater coverage rates than other bondbreakers. • Provided in agitator drums. • Water-based formulation; meets most stringent VOC regulations.
Meets all federal and local VOC requirements. Dry Time (700F): 1 hour
Cure Coat: 400 ft2 per gal. 1st Bondbreaker Coat: 500 - 700 ft2 per gal. 2nd Bondbreaker Coat: 550 - 700 ft2 per gal. Packaging
Product Code
5 gallon pails
30.15.10525
55 gallon drums
30.15.10535
Atlas Easy-Lift FDTM is the premier bondbreaker on the market to produce a clean and easy panel lift. In addition to the bondbreakers, Atlas provides contractors with a complete tilt-up package, including inserts, brace rentals, engineering, etc.
Maintenance
Technical Data & Specifications
Coverage
Atlas Easy-Lift FDTM is a fast-drying formulation that allows contractors to quickly get back on the slab to form panels and place reinforcing steel. It also minimizes the accumulation of dirt and dust on the surface; therefore producing cleaner panels.
Atlas Easy-Lift bondbreakers leave no residue on the concrete surface. Once all panels have been lifted and placed, the walls may be patched, painted or coated. Follow the surface preparation & application instructions of these other applied materials. The concrete floor, if left exposed, may be sealed with Atlas Elite-HSTM. This concrete hardener & sealer will provide a very durable concrete floor with an attractive low-gloss sheen finish that will last the lifetime of the concrete. See Elite-HSTM product data sheet for additional information.
Read Product Data Sheet & MSDS prior to use.
96
www.atlasform.com
Serving Concrete Customers Since 1980.
Bondbreakers for Tilt-up & Precast
Description
• Provides an easier lift of tilt-up panels than other bondbreakers. • Chemically reactive formulation minimizes “osmoticeffect”; panel surface will be stronger and have a more uniform and clean appearance. • Strong, smooth, uniform and clean panels result in minimal sacking/patching costs. • Easy to apply; no back-rolling required. • Rain resistant after coats dry. • Resists construction foot traffic during placement of reinforcing steel. • Does not contain waxes, resins or silicones. • Will not impair the adhesion of paints or coatings after the panels have been lifted and placed, when applied according to manufacturer’s application instructions. • Safe and easy to use; low odor. • Economical bondbreaker system; better coverage rates than other bondbreakers. • Water-based formulation; meets most stringent VOC regulations.
ETM
Atlas Easy-Lift is a high-performance, chemically reactive, water-based cure and bondbreaker for tilt-up and precast construction. Easy-Lift ETM is applied to the concrete casting slab to efficiently prevent the bonding of subsequent concrete pours. This premium-grade bondbreaker contains organic compounds that react with the excess lime in concrete. The reaction produces a gel in the pores of the concrete which effectively forms a water impermeable barrier. When the tilt-up panel is poured, the barrier restricts the casting slab from absorbing the mix water from the panel, which results in an easy to lift panel and a strong, smooth, uniform and clean panel appearance. Easy-Lift ETM meets all federal and local VOC regulations.
Technical Data & Specifications Meets all federal and local VOC requirements. Dry Time (700F): 2 hours
30-ATLAS TECH PRODUCTS
Features of Atlas Easy-Lift ETM
20-FORMING ACCESSORIES
Premium Water-Based Cure & Bond Breaker for Tilt-Up & Precast
10-FORMING & SHORING
ATLAS EASY-LIFT ETM
Coverage Packaging
Product Code
5 gallon pails
30.15.10025
55 gallon drums
30.15.10035
40-BAR SUPPORTS
Cure Coat: 400 ft2 per gal. 1st Bondbreaker Coat: 500 - 700 ft2 per gal. 2nd Bondbreaker Coat: 550 - 700 ft2 per gal. Read Product Data Sheet & MSDS prior to use.
50-FLATWORK ACCESSORIES
ATLAS EASY-LIFT STM
Premium Solvent-Based Cure & Bond Breaker for Tilt-Up & Precast
Description
Cure Coat: 400 ft2 per gal. 1st Bondbreaker Coat: 500 - 700 ft2 per gal. 2nd Bondbreaker Coat: 550 - 700 ft2 per gal.
Packaging
Product Code
5 gallon pails
30.15.11025
55 gallon drums
30.15.11035
80- TOOLS & PLACING
Coverage
PRODUCTS
Dry Time (700F): 30 - 60 minutes
• Provides an easier lift of tilt-up panels than other bondbreakers. • Dries quickly to minimize accumulation of dirt and dust on casting surface, resulting in cleaner panels. Also allows crews to get on slab earlier to form panels and place reinforcing steel. • Chemically reactive formulation minimizes “osmotic-effect”; panel surface will be stronger and have a more uniform and clean appearance. • Strong, smooth, uniform and clean panels result in minimal sacking/patching costs. • Easy to apply; no back-rolling required. • Rain resistant after coats dry. • Does not contain waxes, resins or silicones. • Will not impair the adhesion of paints or coatings after the panels have been lifted and placed, when applied according to manufacturer’s application instructions. • Does not need to be agitated prior to application.
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
70- FOUNDATION
Technical Data & Specifications
Features of Atlas Easy-Lift STM
60-PRECAST & TILT-UP
Atlas Easy-Lift STM is a high-performance, chemically reactive, solvent-based, fast drying cure and bondbreaker for tilt-up and precast construction. Easy-Lift STM is applied to the concrete casting slab to efficiently prevent the bonding of subsequent concrete pours. This premium-grade bondbreaker contains organic compounds that react with the excess lime in concrete. The reaction produces a gel in the pores of the concrete which effectively forms a water impermeable barrier. When the tilt-up panel is poured, the barrier restricts the casting slab from absorbing the mix water from the panel, which results in an easy to lift panel and a strong, smooth, uniform and clean panel appearance. Easy-Lift STM contains a red fugitive dye to aid in the application process.
97
20-FORMING ACCESSORIES
10-FORMING & SHORING
Construction Chemicals
Contractor Committed.
ATLAS CITRUS-CLEAN Strong & Safe Citrus-Based, Multi-Purpose Cleaner, Degreaser & Stripper
Description
Features of Atlas Citrus-Clean
Atlas Citrus-Clean is a strong and environmentally safe concrete cleaner, degreaser and stripper. Formulated from orange peels and designed as a multi-purpose cleaning solution, Citrus-Clean may be used on concrete surfaces to remove oil spills, grease, black tire marks, curing compounds, cutback adhesives and other stubborn materials and stains. Citrus-Clean will not etch the concrete surface, has a pleasant citrus scent, and is easily rinsed-away with water.
• A strong and safe cleaner, degreaser and stripper for concrete surfaces. • Effectively removes tough and stubborn materials and stains. • Safe to use in many different locations - restaurants, hospitals, schools, food processing plants, etc. • Pleasant to use; nice citrus scent. • Dilute and rinse with water for different cleaning strengths. • Does not etch concrete surfaces. • Non-toxic, non-flammable and non-carcinogenic; less risk of EPA or OSHA fines and employee health related lawsuits. • Cleans-up with just water.
• Effectively cleans concrete surface of oil spills, grease, black rubber tire marks, stains and other stubborn contaminants. • Ideal for warehouses, industrial plants, factories, parking garages, airport runways, loading docks, and shipping & receiving areas. • Strips curing compounds and floor sealers. • Removes un-cured epoxies from tools and equipment. • Prepares concrete surfaces for application of sealers and overlays. • Interior and exterior applications. Read Product Data Sheet & MSDS prior to use.
Technical Data & Specifications VOC Compliant Meets USDA specifications for use in food processing areas. Typical Coverage: 150 ft2 per gal. Packaging
Product Code
1 gallon jugs
30.13.10020
5 gallon drums
30.13.10025
55 gal drums
30.13.10035
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
Uses
98
www.atlasform.com
Serving Concrete Customers Since 1980.
Surface Retarder
10-FORMING & SHORING
ATLAS TOP-ETCH
Spray-Applied Surface Retardant for Concrete Flatwork
Description
20-FORMING ACCESSORIES
Atlas Top-Etch is an easy to use, liquid surface retardant that is sprayed onto fresh concrete to produce beautiful exposed aggregate concrete flatwork. Top-Etch is designed to retard the set of portland cement at the surface while the concrete below the surface cures normally. This treatment provides an excellent economical architectural finish highlighting the natural color and texture of the aggregates. Top-Etch is available in regular (blue) or deep (red) strengths.
Uses Atlas Top-Etch is easy to apply & provides a consistent & economical exposed aggregate architectural finish for driveways, patios, shopping plazas, sidewalks, etc. After Top-Etch application, protect the exposed aggregate concrete with an application of Atlas Expo-SealTM.
VOC Compliant Typical Coverage: 100 - 150 ft2 per gal. Atlas Top-Etch Packaging
Product Code
1 gallon jugs
35.10.10520
5 gallon pails
35.10.10525
50-FLATWORK ACCESSORIES
• Economical treatment to concrete flatwork that provides an excellent architectural finish highlighting the original color and texture of the aggregates. • Consistent and uniform results. • Easy to use spray-apply formulation with a fugitive dye for identification of treated areas. • No expensive equipment needed for application. • Cleans-up with water. • Much cleaner and less expensive than sandblasting. • May be used with colored concrete. • Water-based formulation; no odor and no acid residue.
40-BAR SUPPORTS
Technical Data & Specifications
Features
Read Product Data Sheet & MSDS prior to use.
30-ATLAS TECH PRODUCTS
• Exposes the aggregate in fresh concrete on floor slabs, sidewalks, entryways, driveways, patios, pool decks, etc. • Ideal for shopping plazas, schools, stadiums, lobbies, residences, or any concrete flatwork where an economical architectural finish is desired. • Provides a roughened surface for bonding subsequent coatings or treatments to the concrete. • Interior and exterior applications.
Atlas Top-Etch Deep Packaging
Product Code
1 gallon jugs
35.10.11020
5 gallon pails
35.10.11025
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
99
PRODUCTS
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Liquid Bonding Agents
Contractor Committed.
ATLAS ACRYL-BOND Acrylic Latex Bonding Agent & Admixture for Portland Cement, Patching Materials and other construction products.
Features of Atlas Acryl-Bond Description Atlas Acryl-Bond is a high-strength, non-reemulsifiable, acrylic latex emulsion for use as a bonding agent or admixture for concrete repair mortars, patching materials, grouts, masonry coatings and other cement-based products. Acryl-Bond significantly enhances the performance of cement-based materials by improving the adhesion, compressive, tensile and flexural strengths of the materials and provides excellent resistance to freeze/thaw cycles for both interior and exterior applications.
Uses • Mix with repair mortars, patching materials, grouts, masonry coatings and other cement-based products for increased adhesion and durability. • Bonding new concrete to aged concrete. • Bonding stucco, mortar or plaster to sound surfaces. • Interior and exterior applications. • Above and below grade applications. • Ideal for use with patching materials for concrete floors, walkways, ramps, walls, columns and beams.
• Improves bond, compressive, tensile and flexural strengths of cement-based materials. • Provides excellent adhesion for a superior bond to the existing surface. • Produces more durable and impact resistant repair mortars and patches. • Improves stability through freeze/thaw cycles and resistance to moisture penetration & chemical attack. • Both interior and exterior applications; will not re-emulsify when exposed to water. • Water-based formulation; meets most stringent VOC regulations. • Easy to use, low odor.
Technical Data & Specifications ASTM C-1059, Type 2 VOC Compliant Packaging
Product Code
1 gallon jugs
30.25.10020
5 gallon pails
30.25.10025
55 gallon drums
30.25.10035
Read Product Data Sheet & MSDS prior to use.
ATLAS H2 BOND
Features of Atlas H2 Bond
Cement bonding agent and admixture for H2 patch & overlay
Description Atlas H2 Bond is a next generation cement bonding agent and admixture specifically formulated to increase the flexural, bond and early and overall compressive strength of modified mixes. Both lab testing and field applications show increased strengths, and more durable, long lasting patches will be achieved. Atlas H2 Bond can be used as an admixture to greatly enhance the adhesion of cement mortars as well as improve resistance to oil, water, salt and chemical penetration. Atlas H2 Bond exhibits excellent resistance to freeze/thaw cycles and can be used for interior or exterior applications.
Uses
• Durable: Increase bond strength, flexural strength, compressive strength and chemical resistance over non-modified mortars. • Curing: Increase water retention properties. • Excellent bonding agent: Superior adhesion properties. • Freeze/Thaw resistance: Increased resistance to dramatic climatic changes. • Consistent: Strict quality control testing and standards.
Technical Data & Specifications ASTM C-1059, Type 2 VOC Compliant
Packaging
Product Code
1 gallon jugs
35.25.10520
• Bonding new concrete to old concrete in interior or exterior applications. • Designed for use with cementitious compositions such as patching materials, grouts, masonry coatings, stucco coatings and masonry mortars to increase chemical resistance and performance.
80- TOOLS & PLACING
Read Product Data Sheet & MSDS prior to use.
100
www.atlasform.com
Liquid Bonding Agents
Serving Concrete Customers Since 1980.
Apply up to 7 days before pouring concrete! • Superior adhesion for placing concrete, repair mortars, patching materials, underlayments and other cementbased products. • Re-emulsifiable bonding agent allows an extended time, up to 7 days, for placing concrete or subsequent toppings & coatings. • Will re-emulsify only one time within 7 days of bonder application. • Improves bond, compressive, tensile and flexural strengths of cement-based materials when used as an admixture. • Produces more durable and impact resistant repair mortars and patches. • Improves workability of cement-based materials. • High solids formulation that may be diluted with water to achieve desired consistency. • Water-based formulation; meets most stringent VOC regulations. • Easy to use, low odor.
Atlas Tech-Bond is a premium, high-solids, re-emulsifiable, ethyl-vinyl acetate (EVA) emulsion for use as a bonding agent or admixture when placing concrete, repair mortars, patching materials, underlayments, grouts, masonry coatings and other cement-based products. Tech-Bond establishes a superior bond strength when compared to acrylic or PVA bonding agents. Tech-Bond provides an extended open time for placement of concrete, repair mortars, patching materials, stucco and plaster, and is ideal for use as a primer prior to placing self-leveling underlayments. This bonding agent may be applied up to 7 days prior to pouring, patching or coating, and will re-emulsify only 1 time within 7 days of application. Tech-Bond is an easy to use product that improves the adhesion, compressive, tensile and flexural strengths of cement-based materials.
Uses
Technical Data & Specifications ASTM C-1059, Type 1 ASTM C-1042, Type 1 VOC Compliant Packaging
Product Code
1 gallon jugs
30.25.11520
40-BAR SUPPORTS
• Bonding new concrete to aged concrete. • Bonding patching materials to concrete, masonry or brick. • Mix with repair mortars, patching materials, grouts, masonry coatings and other cement-based products for increased adhesion and durability. • Use as a primer prior to placing self-leveling underlayments. • Interior or exterior applications.
5 gallon pails
ATLAS INTER-BOND
Re-emulsifiable, Poly-Vinyl Acetate Bonding Agent & Admixture for Portland Cement, Patching Materials & other construction products
Description
ASTM C-1059, Type 1 ASTM C-1042, Type 1 VOC Compliant Packaging
Product Code 30.25.11020 30.25.11025
55 gallon drums
30.25.11035
80- TOOLS & PLACING
1 gallon jugs 5 gallon pails
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
PRODUCTS
• Mix with repair mortars, underlayments, patching materials, masonry coatings & other cement-based or gypsum-based products for increased adhesion & durability. • Bonding new concrete to aged concrete. • Bonding stucco, mortar or plaster to sound surfaces. • Dry interior applications. • Will bond to concrete, brick, tile, stone, block, plaster, gypsum board, lath or plywood.
Technical Data & Specifications
70- FOUNDATION
Uses
• Re-emulsifiable bonding agent allows an extended open time, up to 24 hours, for applications of subsequent toppings or coatings. • Provides excellent adhesion for a superior bond to the existing surface. • Improves bond, compressive, tensile and flexural strengths of cement-based materials when used as an admixture. • Produces more durable and impact resistant repair mortars and patches. • Water-based formulation; meets most stringent VOC regulations. • Easy to use, low odor.
60-PRECAST & TILT-UP
Atlas Inter-Bond is a general purpose, re-emulsifiable, poly-vinyl acetate emulsion for use as a bonding agent or admixture for repair mortars, patching materials, underlayments, grouts, masonry coatings, and other cement-based products. Inter-Bond provides increased adhesion and an extended open time for placing concrete, coatings and other toppings to existing concrete or other sound substrates for dry interior applications. This bonding agent may be applied up to 24 hours prior to pouring, patching or coating. Inter-Bond is an easy to use product that improves the adhesion, compressive, tensile and flexural strengths of cementbased materials.
Features of Atlas Inter-Bond
50-FLATWORK ACCESSORIES
55 gallon drums
Read Product Data Sheet & MSDS prior to use.
30-ATLAS TECH PRODUCTS
Features of Atlas Tech-Bond
Description
20-FORMING ACCESSORIES
Premium, Re-emulsifiable Ethyl-Vinyl Acetate Bonding Agent
10-FORMING & SHORING
ATLAS TECH-BOND
101
Contractor Committed.
Structural Epoxy Adhesives
10-FORMING & SHORING
EPOXY APPLICATION GUIDE
20-FORMING ACCESSORIES
BONDING
ATLAS EPOXY BONDER ATLAS LPL EPOXY BONDER
BINDING IRREGULAR SURFACES
ATLAS HI-MOD EPOXY GEL
ATLAS HI-MOD EPOXY GEL
ANCHORING THREADED RODS, BOLTS,
UNITEX PRO-POXY 300
DOWELS, SCREENS, ETC.
UNITEX PRO-POXY 300 FAST
30-ATLAS TECH PRODUCTS
UNITEX PRO-POXY 400
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
CRACK INJECTION
DELAMINATION REPAIR
ATLAS E-PRO SEAL SLV
HAIR LINE CRACKS (0.05 - 0.2 MM)
ATLAS INJECTION RESIN 175
FINE CRACKS (0.2 - 0.5 MM)
ATLAS LV INJECTION EPOXY UNITEX PRO-POXY 100
CRACKS (0.5 - 0.8MM)
ATLAS EPOXY BONDER
WIDE CRACKS & VOIDS ( > 0.8 MM)
ATLAS HI-MOD EPOXY GEL UNITEX PRO-POXY 300 UNITEX PRO-POXY 300 FAST
CAP SEALING & PORT SETTING
ATLAS HI-MOD EPOXY GEL UNITEX PRO-POXY 300 UNITEX PRO-POXY 300 FAST
CONTROL JOINTS / SAW-CUTS
ATLAS EPOXY JOINT FILLER
OVERLAYS FOR BRIDGES, PARKING DECKS, ETC.
ATLAS E-PRO OVERLAY ATLAS TECH-DECK
CONCRETE SURFACES & CRACK HEALER-SEALER FOR BRIDGES, PARKING DECKS, ETC.
ATLAS E-PRO SEAL SLV ATLAS TECH SEAL HMWM
PRODUCTS
60-PRECAST & TILT-UP
SEALING
80- TOOLS & PLACING
70- FOUNDATION
NEW TO OLD CONCRETE & OLD TO NEW CONCRETE
Atlas Injection Resin 175 is a very low viscosity epoxy that will penetrate hairline cracks.
102
Atlas LV Injection Epoxy is a 100% solids easy to pump injection resin to structurally restore concrete structures.
www.atlasform.com
Serving Concrete Customers Since 1980.
Low Viscosity Epoxies / Injection Resins
100% Solids, High Strength, Low Viscosity Epoxy Resin
Technical Data & Specifications ASTM C-881: Types I, II, IV & V, Grade 1, Classes B & C. Meets USDA specifications for use in food processing areas. VOC Compliant. Cures to a transparent amber color. See Testing Data Chart for test results. Packaging
Product Code
30-ATLAS TECH PRODUCTS
1.5 quart kits (3 - 0.5 quart cans) 3 gallon kits (3 - 1 gal. cans)
30.20.12523
15 gallon kits (3 - 5 gal. pails)
30.20.12530
40-BAR SUPPORTS
Uses • Pressure-inject horizontal, vertical or overhead cracks for a structural repair of concrete structures. • Gravity-feed horizontal concrete and masonry cracks. • Grout anchor bolts, dowels and reinforcing steel. • Mix with aggregate to repair concrete spalls and voids as an epoxy repair mortar. • Seal interior slabs and exterior above grade slabs to protect concrete and reinforcing steel from moisture, chlorides and chemical attack. • Bonding new concrete to hardened concrete or patching materials to hardened concrete. • Bonding wood, masonry & other construction materials. • Interior or exterior applications.
Features of Atlas Injection Resin 175 • Excellent bond strength to many materials. • Moisture tolerant to allow for application on both dry or wet surfaces. • Super low-viscosity (175 cps) consistency for deep penetration of concrete cracks. • High-modulus for superior strength. • Good chemical resistance to protect concrete slabs and decks. • Low odor formulation. • Proven field performance.
20-FORMING ACCESSORIES
Description Atlas Injection Resin 175 is a two-component, 100% solids, high modulus, high strength, very low viscosity epoxy resin adhesive for multiple uses. Injection Resin 175 is an ideal material for repairing concrete cracks to structurally restore the integrity of concrete structures. This moisture tolerant epoxy provides excellent penetration of concrete cracks by pressure injection or by gravity-feed methods. Injection Resin 175 conforms to ASTM C-881 specifications.
10-FORMING & SHORING
ATLAS INJECTION RESIN 175
165 gallon kits (3 - 55 gal. drums)
Read Product Data Sheet & MSDS prior to use.
100% Solids, High Strength, Low Viscosity Multi-Purpose Epoxy Resin
Packaging
Product Code
1.5 quart kits (3 - 0.5 quart cans)
30.20.13013
3 gallon kits (3 - 1 gal. cans)
30.20.13023
15 gallon kits (3 - 5 gal. pails)
30.20.13030
80- TOOLS & PLACING
Technical Data & Specifications ASTM C-881: Types I, II, IV & V, Grade 1, Classes B & C. Meets USDA specifications for use in food processing areas. VOC Compliant. Cures to a transparent amber color. See Testing Data Chart for test results.
165 gallon kits (3 - 55 gal. drums)
www.atlasform.com
PRODUCTS
Uses • Pressure-inject horizontal, vertical or overhead cracks for a structural repair of concrete structures. • Grout anchor bolts, dowels and reinforcing steel. • Mix with aggregate to repair concrete spalls and voids as an epoxy repair mortar. • Seal interior slabs and exterior above grade slabs to protect concrete and reinforcing steel from moisture, chlorides and chemical attack. • Bonding new concrete to hardened concrete or patching materials to hardened concrete. • Bonding wood, masonry & other construction materials. • Interior or exterior applications.
70- FOUNDATION
Features of Atlas LV Injection Epoxy • Excellent bond strength to many materials. • Moisture tolerant to allow for application on both dry or wet surfaces. • Low-viscosity (500 cps) consistency for deep penetration of concrete cracks. • High-modulus for superior strength. • Good chemical resistance to protect concrete slabs and decks. • Low odor formulation. • Proven field performance.
60-PRECAST & TILT-UP
Description Atlas LV Injection Epoxy is a two-component, 100% solids, high modulus, high strength, low viscosity epoxy resin adhesive for multiple uses. LV Injection Epoxy is an ideal material for repairing concrete cracks to structurally restore the integrity of concrete structures. This moisture tolerant epoxy provides excellent bond strength for grouting dowels & bolts and may also be mixed with aggregate to produce a high strength, fast-setting mortar. LV Injection Epoxy conforms to ASTM C-881 specifications.
50-FLATWORK ACCESSORIES
ATLAS LV INJECTION EPOXY
103
Contractor Committed.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Structural Epoxy Adhesives, Medium Viscosity
ATLAS EPOXY BONDER
100% Solids, High Strength, Medium Viscosity, Multi-Purpose Epoxy Adhesive
Description Atlas Epoxy Bonder is a two-component, 100% solids, high modulus, high strength, medium viscosity epoxy adhesive for multiple uses. Epoxy Bonder is an excellent material for bonding new concrete to old concrete, bonding steel to concrete, and for repairing concrete cracks. This moisture tolerant epoxy provides excellent bond strength for grouting dowels & bolts and may also be mixed with aggregate to produce a high strength, fast-setting mortar. Epoxy Bonder conforms to ASTM C-881 specifications. Uses • Bonding new concrete to hardened concrete. • Bonding steel to new or hardened concrete. • Use as a binder for concrete, masonry, wood and steel. • Structural crack repairs. • Mix with aggregate for an epoxy grout or mortar. • Grout anchor bolts, dowels and reinforcing steel. • Multi-purpose pourable adhesive. • Interior or exterior applications.
Features of Atlas Epoxy Bonder • Excellent bond strength to many materials. • Moisture tolerant to allow for application on both dry or wet surfaces. • Sets rapidly for early strength. • Easy to use, low odor, 1:1 mix ratio. • Cures to a concrete gray color. • Proven field performance. Technical Data & Specifications ASTM C-881, Types I, II, IV & V, Grade 2, Classes B & C. VOC Compliant See Product Data Sheet for test results Packaging
Product Code
2 quart kits (2 - 1 quart cans) 2 gallon kits (2 - 1 gal. cans)
30.20.10522
10 gallon kits (2 - 5 gal. pails)
30.20.10527
110 gallon kits (2 - 55 gal. drums)
Read Product Data Sheet & MSDS prior to use.
ATLAS LPL EPOXY BONDER
100% Solids, High Strength, Medium Viscosity, Multi-Purpose Epoxy Adhesive With a Long Pot Life
Description Atlas LPL Epoxy Bonder is a two-component, 100% solids, high modulus, high strength, medium viscosity, multi-purpose epoxy adhesive with an extended setting time. LPL Epoxy Bonder is an excellent material for bonding new concrete to old concrete, bonding steel to concrete, and for coating reinforcing steel as a corrosion inhibitor. The extended pot life of this epoxy provides extra time and easy application for placing concrete, repair mortars, and other materials. This moisture tolerant epoxy provides excellent bond strength for grouting dowels & bolts and may also be mixed with aggregate to produce a high strength epoxy mortar. LPL Epoxy Bonder conforms to ASTM C-881 specifications. Uses • Bonding new concrete to hardened concrete. • Bonding steel to new or hardened concrete. • Use as a binder for concrete, masonry, wood and steel. • Apply to reinforcing steel as a corrosion inhibitor. • Structural crack repairs. • Mix with aggregate for an epoxy grout or mortar. • Grout anchor bolts, dowels and reinforcing steel. • Interior or exterior applications.
Features of Atlas LPL Epoxy Bonder • Excellent bond strength to many materials. • Extended pot life for ease of application; especially useful during high ambient temperatures. • Moisture tolerant to allow for application on both dry or wet surfaces. • Tough coating protects reinforcing steel from moisture and chlorides. • May be spray-applied. • Cures to a concrete gray color. • Low odor formulation. • Proven field performance. Technical Data & Specifications ASTM C-881, Types I, II & V, Grade 2, Classes B & C. VOC Compliant See Product Data Sheet for test results Packaging 1.5 quart kits (3 - 0.5 quart cans)
30.20.11013
3 gallon kits (3 - 1 gal. cans)
30.20.11023
15 gallon kits (3 - 5 gal. pails)
30.20.11030
165 gallon kits (3 - 55 gal. drums)
Read Product Data Sheet & MSDS prior to use.
104
Product Code
www.atlasform.com
Structural Epoxy Adhesive, Non-Sag
Serving Concrete Customers Since 1980.
100% Solids, High Strength, Non-Sag Epoxy Gel Adhesive
Features of Atlas Hi-Mod Epoxy Gel
Description
Uses
Technical Data & Specifications ASTM C-881, Types I, II, IV, & V, Grade 3, Classes B & C. Meets USDA specifications for use in food processing areas. VOC Compliant See Product Data Sheet for test results Packaging
Product Code
2 quart kits (2 - 1 quart cans) 2 gallon kits (2 - 1 gal. cans)
30.20.11522
10 gallon kits (2 - 5 gal. pails)
30.20.11527
40-BAR SUPPORTS
• Structural bonding of concrete, steel, wood, masonry and other materials. • Chemical anchoring for bolts, dowels, pins, etc. • Seal cracks and set injection ports for pressure-injection of concrete cracks. • Pressure-inject cracks for a structural repair of concrete structures. • Mix with aggregate to repair concrete spalls and voids as a non-sag epoxy repair mortar. • Horizontal, vertical and overhead applications. • Interior or exterior applications.
30-ATLAS TECH PRODUCTS
• Excellent bond strength to many materials. • Moisture tolerant to allow for application on both dry or wet surfaces. • Sets quickly for rapid strength gain and load capacity. • Non-sag consistency is ideal for vertical or overhead applications. • High strength, heavy-duty concrete patching material for horizontal, vertical or overhead surfaces. • Cures to a gray color. • Easy to use, low odor, 1:1 mix ratio. • Proven field performance.
20-FORMING ACCESSORIES
Atlas Hi-Mod Epoxy Gel is a two-component, 100% solids, high modulus, high strength, non-sag, multipurpose epoxy gel adhesive. Hi-Mod Epoxy Gel is an excellent material for structural bonding of concrete, steel, wood, masonry and other materials. This moisture tolerant epoxy gel is the ideal consistency to seal cracks and set injection ports prior to injecting cracks with epoxy. Hi-Mod Epoxy Gel is easy to use for horizontal, vertical or overhead concrete repair applications and conforms to ASTM C-881 specifications. Also available in a paste consistency.
10-FORMING & SHORING
ATLAS HI-MOD EPOXY GEL
110 gallon kits (2 - 55 gal. drums)
Material Water
1
Milk
3
E-Pro Seal SLV
85-140
SAE 20 Motor Oil
140-420 175
LV Injection Epoxy
500
SAE 40 Motor Oil
650-900 1,000
E-Pro Overlay
1,800
Epoxy Joint Filler
2,200
Epoxy Bonder
2,500
Karo Syrup
5,000
LPL Epoxy Bonder
6,500
Honey
10,000 50,000
Sour Cream
100,000
Peanut Butter
250,000
Hi-Mod Epoxy Gel
300,000
80- TOOLS & PLACING
Ketchup
PRODUCTS
Castor Oil
70- FOUNDATION
www.atlasform.com
< 50
SAE 10 Motor Oil
Injection Resin 175
Atlas Hi-Mod Epoxy Gel is a non-sag viscosity and is ideal for setting injection ports and cap sealing.
Viscosity in Centipoise (CPS)
60-PRECAST & TILT-UP
Atlas Epoxy Bonder is a medium viscosity bonding agent that is easy to broom-apply; ideal for bonding new concrete to old concrete. Use the LPL Epoxy Bonder for up to an 8 hour open time at 700F!
50-FLATWORK ACCESSORIES
EPOXY VISCOSITIES
105
Contractor Committed.
ATLAS EPOXY JOINT FILLER 100% Solids, Self-Leveling, Semi-Rigid Epoxy Joint Filler
Description Atlas Epoxy Joint Filler is a two-component, 100% solids, self-leveling, high strength, semi-rigid epoxy joint filler for industrial concrete floors. This moisture tolerant and easy to use joint filler provides ultimate support and protection for saw-cut or formed control joints in concrete floors that are subjected to hard-wheeled vehicle traffic.
ASTM C-881: Grade 2, Classes B & C. Meets USDA specifications for use in food processing areas. VOC Compliant See Testing Data Chart for test results
• Fill and seal control and construction joints (saw-cut or formed) in concrete slabs. • Fill and repair spalls or cracks in concrete floors and joint nosings. • New concrete floors or joint restoration projects. • Ideal for industrial and commercial floors, warehouses, distribution centers, factories, food processing plants, maintenance facilities, parking structures, etc. • Interior applications.
Product Code
2 gallon kits (2 - 1 gal. cans)
30.28.10022
10 gallon kits (2 - 5 gal. pails)
30.28.10027
110 gallon kits (2 - 55 gal. drums)
Coverage
Features of Atlas Epoxy Joint Filler • Protects joint edges from spalling and deteriorating, even when subjected to heavy forklift traffic. • Low modulus formulation allows for moderate joint movement. • High elongation; will not tear from concrete. • Excellent shock absorption from heavy impact loads. • Resistant to gasoline, oil and most common chemicals. • Moisture tolerant to allow for application on both dry or wet surfaces. • Cures to a concrete gray color. • Easy to use, low odor, 1:1 mix ratio. • No primer necessary. • Self-leveling consistency for simple application. • Will not become brittle over time. • Proven field performance.
f roo ints p k jo pic ol g, ontr a c -s on lling ns! n fi o a & ati in le aling pplic b a se a ail av for curity o n Als latio in se u m for
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
Technical Data & Specifications
Packaging
Uses
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Semi-Rigid Epoxy Joint Sealants
Atlas Epoxy Joint Filler is a self-leveling joint sealant that will protect joint edges from spalling & deterioration otherwise caused by forklifts, pallet jacks, etc. Very easy to apply with a caulking gun and cures to a gray color! Read Product Data Sheet & MSDS prior to use.
106
www.atlasform.com
Serving Concrete Customers Since 1980.
Joint Sealants
10-FORMING & SHORING
ATLAS FLEX-THANE 230
One-Component, Gun-Grade, All-Purpose, Elastomeric Construction Sealant
Features of Atlas Flex-Thane 230
Atlas Flex-Thane 230 is a one-component, non-sag, polyurethane construction sealant that cures to a tough, flexible, watertight rubber when exposed to moisture present in the atmosphere. This easy-to-use, highly resilient elastomeric material is capable of +/- 25% joint movement, making it ideal for sealing all vertical or horizontal joints that are subject to contraction and expansion. Flex-Thane 230 exhibits excellent adhesion to concrete, wood, glass and metal for many construction applications.
• Highly elastic durable sealant capable of 50% joint movement(+/- 25%) with excellent tear-resistance. • Excellent adhesion to concrete, wood, glass and metal. • Strong resistance to chemicals, staining, harsh weather and aging. • Service temperature range of -400 - 1800F (-40 - 820C). • Excels in multiple construction applications. • Proven field performance. • Fast and easy to apply. • Available in many colors.
20-FORMING ACCESSORIES
Description
• Caulk and seal expansion and contraction joints, tilt-up panels, precast concrete elements, metal curtain walls, perimeter door and window framing, etc. • Use as an elastic construction adhesive for materials with different coefficients of expansion. • Vertical or horizontal applications. • New construction or restoration projects. • Interior or exterior applications.
Technical Data & Specifications Federal Specification TT-S-00230C, Type II, Class A. ASTM C-920 Type S, Grade NS, Class 25, Use NT, M & A. VOC Compliant See Testing Data Chart for test results Packaging
Product Code
10.5 oz. cartridges
30.28.10503
Read Product Data Sheet & MSDS prior to use.
20.3 oz. sausages
40-BAR SUPPORTS
(12 cartridges per case) 30.28.10507
(20 sausages per case) 5 gallon pails
50-FLATWORK ACCESSORIES
ATLAS FLEX-THANE 230 SL One-Component, Self-Leveling, Elastomeric Construction Sealant
Description
Technical Data & Specifications Federal Specification TT-S-00230C, Type I, Class A. ASTM C-920 Type S, Grade P, Class 25, Use T, M & A. VOC Compliant See Product Data Sheet for test results Packaging
Product Code
30 oz. cartridges (12 cartridges per case)
30.28.11510
80- TOOLS & PLACING
Read Product Data Sheet & MSDS prior to use.
PRODUCTS
• Caulk and seal expansion and contraction joints, parking decks, pavements, sidewalks, plazas, patios, driveways, malls, or other areas subject to foot and light vehicle traffic. • Use as an elastic construction adhesive for materials with different coefficients of expansion. • Horizontal applications. • New construction or restoration projects. • Interior or exterior applications.
• Highly elastic durable sealant capable of 50% joint movement (+/- 25%) with excellent tear-resistance. • Excellent adhesion to concrete, wood, glass and metal. • Strong resistance to chemicals, staining, harsh weather and aging. • Service temperature range of -400 - 1800F (-40 - 820C). • Excels in multiple construction applications. • Proven field performance. • Fast and easy to apply. • Available in many colors.
5 gallon pails
www.atlasform.com
70- FOUNDATION
Uses
Features of Atlas Flex-Thane 230 SL
60-PRECAST & TILT-UP
Atlas Flex-Thane 230 SL is a one-component, selfleveling, polyurethane construction sealant that cures to a tough, flexible, watertight rubber when exposed to moisture present in the atmosphere. This easy-to-use, highly resilient elastomeric material is capable of +/- 25% joint movement, making it ideal for sealing all horizontal joints that are subject to contraction and expansion. Flex-Thane 230 SL exhibits excellent adhesion to concrete, wood, glass and metal.
30-ATLAS TECH PRODUCTS
Uses
107
Contractor Committed.
ATLAS E-PRO SEAL SLV
Super Low Viscosity, Two-Component, Epoxy Healer/Sealer for Protection of New Concrete or Repair of Concrete Cracks
Uses
Description Atlas E-Pro Seal SLV is a two-component, super low viscosity, deep-penetrating, high strength, epoxy sealer designed to protect new concrete and repair deteriorated concrete. E-Pro Seal SLV has a viscosity below 50 cps for maximum penetration into fine cracks and pores in the concrete. To seal the concrete surface and prevent the migration of moisture, chlorides, and other harmful contaminants from getting into the concrete and steel reinforcement. E-Pro Seal SLV is an easy-to-use concrete healer & sealer that will prolong the life of concrete structures, such as bridges, parking garages, elevated decks or other concrete elements subjected to harsh weather and chemical attack.
• Penetrate, fill and seal concrete cracks in bridge decks, parking structures, or other areas subject to chemical attack, harsh weather and heavy traffic. • Delamination repair by gravity-feed method. • Consolidation of porous and dusting surfaces. • Interior or exterior, above grade applications. May also be used for slab-on grade in non-freezing climates.
Features of Atlas E-Pro Seal SLV • High-performance and easy to use epoxy resin for structural repairs of concrete decks and slabs. • Protects concrete surface & reinforcing steel from corrosion by resisting the penetration of water, chlorides or other harmful contaminants. • Super low viscosity for deep crack penetration; will penetrate hairline cracks with gravity-feed method. • Excellent bond and tensile strengths. • Fills and binds concrete cracks for structural repairs. • Cures rapidly for minimal downtime of repaired area. • Minimizes future maintenance of treated surface. • Safe and easy to mix. • May be used for interior or exterior applications.
Technical Data & Specifications E-Pro Seal SLV: AASHTO T-259 Chloride Ion Penetration Resistance (90 day ponding) D.O.T. Approvals See Product Data Sheets for test results E-Pro Seal SLV may be used to penetrate cracks in concrete decks to fill the cracks and seal the surface to protect bridge decks, parking structures or other elevated decks from moisture, chlorides and other harmful contaminants.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Crack Healer / Sealer
Packaging E-Pro Seal SLV
Product Code
2 gallon kits (2 - 1 gal. cans)
30.40.10522
10 gallon kits (2 - 5 gal. pails)
30.40.10527
110 gallon kits (2 - 55 gal. drums)
30.40.10540
E-Pro Seal SLV is very easy to mix and apply. The two components are completely safe to mix together with a drill & mix paddle and then apply by flood coat over the surface with a broom or squeegee. A sand is broadcasted over the treated surface to absorb any material that did not penetrate into the concrete. Read Product Data Sheet & MSDS prior to use.
108
www.atlasform.com
Serving Concrete Customers Since 1980.
Polymer Overlay
10-FORMING & SHORING
ATLAS E-PRO OVERLAY
100% Solids, High Strength, Low Modulus, Low Viscosity Epoxy Binder for Polymer Concrete Overlays & Patching
Description
20-FORMING ACCESSORIES
Atlas E-Pro Overlay is a two-component, 100% solids, high strength, low modulus, low viscosity epoxy binder for concrete patching and overlays. E-Pro Overlay provides a protective and durable polymer concrete repair to concrete bridge decks, parking structures or other areas subjected to heavy traffic, abrasion, thermal movements and chemical attack. This moisture tolerant epoxy binder cures rapidly for minimum downtime of traffic areas. E-Pro Overlay conforms to ASTM C-881 specifications.
Uses 30-ATLAS TECH PRODUCTS
• Concrete bridge deck overlays, parking structures, or other concrete surfaces subject to heavy traffic, abrasion, thermal movements and chemical attack. • Mix with aggregate for a high strength polymer concrete mortar. • Expansion joint nosing repairs. • Low-modulus bonding agent. • Interior or exterior applications.
After the deck surface is cleaned, Atlas E-Pro Overlay is easily applied to the deck with a notched squeegee.
40-BAR SUPPORTS
Features of Atlas E-Pro Overlay
50-FLATWORK ACCESSORIES
After the Atlas E-Pro Overlay is applied, broadcast a clean, hard, angular aggregate to provide good skid resistance. (See your Atlas representative for aggregate recommendations)
PRODUCTS
ASTM C-881, Type III, Grade 1, Classes B & C. AASHTO AGC-ARTBA (Taskforce 34) Meets USDA specifications for use in food processing areas. VOC Compliant D.O.T. Approvals See Product Data Sheet for test results
80- TOOLS & PLACING
Packaging
Product Code
2 gallon kits (2 - 1 gal. cans) 10 gallon kits (2 - 5 gal. pails)
30.40.12527
110 gallon kits (2 - 55 gal. drums)
30.40.12540
A finished bridge lane after being treated with Atlas E-Pro Overlay. The overlay is applied at approximately 3/8” thick.
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
70- FOUNDATION
Technical Data & Specifications
60-PRECAST & TILT-UP
• High-performance and easy to use binder for skid resistant broadcast overlays. • Durable overlay that provides excellent protection from heavy traffic and abrasion; excellent riding surface. • Low-modulus for excellent shock absorption and thermal movement. • Impermeable to water, de-icing salts (chlorides) and other harmful chemicals. Protects steel reinforcement from corrosion. • High early strength; cures rapidly for minimal downtime of repaired area. • Moisture tolerant before and after cure; allows for application on both dry or damp surfaces. • Minimizes future maintenance of treated surface. • 1:1 component ratio is safe and easy to mix. • Non-flammable. • Low odor; may be used for interior or exterior applications. • Provides an attractive finish to bridge decks, parking structures, etc. • Proven field performance.
109
Contractor Committed.
ATLAS TECH-DECK
TM
Polyester Concrete Overlay & Patch for Bridge Deck Restoration
High Molecular Weight Methacrylate Primer/Sealer
Tech-DeckTM
Atlas is high-strength, rapid-setting, water impermeable polyester concrete patch and overlay material for the rehabilitation of concrete bridge decks, parking structures, highways, and other concrete surfaces that are exposed to heavy traffic, abrasion, harsh weather and chemical attack. Tech-DeckTM is composed of a polyester resin binder and select aggregates to provide a durable wearing surface that is resistant to moisture, chlorides and other chemicals that would otherwise penetrate the concrete and corrode steel reinforcement. Tech-DeckTM cures rapidly, allowing fast return to lane service.
Atlas Tech-Seal high molecular weight methacrylate is applied as a primer before placing Atlas Tech-DeckTM. As shown above, the methacrylate is applied to the clean bridge deck surface with brooms. Contact your Atlas representative for further information on methacrylate sealers.
• Concrete bridge deck overlays, parking structures, or other concrete surfaces subject to heavy traffic, abrasion, thermal movements and chemical attack. • Mix with aggregate for a high strength polymer concrete patching mortar. • Expansion joint nosing repairs.
Features of Atlas Tech-Deck
TM
• Provides excellent protection from moisture, chlorides and other harmful contaminants. Protects the concrete and steel reinforcement from corrosion, providing a longer service life for bridges, parking structures, etc. • Superior abrasion and skid resistance to provide a safe and durable riding surface. • Rapid curing to minimize traffic disruption. Traffic is returned to lanes within 4 hours of application. • Very dense surface protects bridge deck from extreme wear, including snow chain abrasion/snow plow equipment. • Greater tensile strength and elongation than competitive overlays. • Resilient and shock-absorbing overlay does not crack or delaminate, even through extreme freeze/thaw cycles. • Significantly reduces future bridge deck maintenance and repair costs. • Low viscosity resin is easy to mix, place and finish. • Can modify cure time for specific jobs and temperatures. • Stronger than portland cement concrete. • Greater bond strength, protection and service life than latex-modified concrete and silica fume concrete. • Provides an attractive finish to bridge decks, parking structures, etc. • Proven field performance. • Meets California Air Resource Board (CARB).
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
/ ATLAS TECH-SEAL HMWM Uses
Description
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Polyester Concrete & Methacrylate Sealer
Read Product Data Sheet & MSDS prior to use.
110
Atlas Tech-DeckTM may be placed using a vibrating screed as shown on the left, or with a mobile mixing & paving system as shown above. Specific jobsite conditions will determine which application equipment is best suited for a successful placement.
www.atlasform.com
Serving Concrete Customers Since 1980.
Non-Shrink Grouts
10-FORMING & SHORING
ATLAS CONSTRUCTION GROUT Non-Shrink, Non-Metallic, Multi-Purpose Cement-Based Grout
Description
Technical Data & Specifications ASTM C-1107, Grade B; CRD C-621 AASHTO T-260 Multiple DOT approvals
20-FORMING ACCESSORIES
Atlas Construction Grout is a blend of portland cement, natural aggregates and special additives to provide a non-shrink, non-metallic, non-corrosive, non-gas forming grout for multiple applications. Construction Grout is a flowable and pumpable grout that will provide maximum bearing area for proper support and load transfer for column baseplates, precast & tilt-up panels, and other structural grouting applications.This high strength grout may be mixed to a range of consistencies, from dry-pack to fluid, to provide contractors with a quality, multi-use grout.
Compressive Strength (Flowable): 1 day - 2,500 psi 3 days - 4,400 psi 7 days - 5,300 psi 28 days - 6,800 psi
Yield
• Structural column baseplates. • Machinery, equipment and pump baseplates. • Precast walls and tilt-up panels. • Anchor bolts and dowels.
Approximately 0.43 ft3 per 50 lb. bag when mixed with 4.0 quarts of water. At 1” thickness, one 50 lb. bag will cover approximately 5.2 ft2. When one 50 lb. bag is mixed with 4.0 quarts of water & 25 lbs. of 3/8” pea gravel, yield is approximately 0.61 ft3 .
Features of Atlas Construction Grout
Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.30.10060
40-BAR SUPPORTS
• High-strength for load stability. • Non-metallic, will not stain or rust. • Non-corrosive, does not contain calcium chloride. • Non-gas forming. • Versatile grouting, from dry-pack to fluid consistencies. • Can be molded and shaped.
Read Product Data Sheet & MSDS prior to use.
Uses
ASTM C-1107, Grade B; CRD C-621; AASHTO T-260 City of Los Angeles Approved. RR# 25526 Compressive Strength (Flowable): 1 day - 3,700 psi 3 days - 6,200 psi 7 days - 7,100 psi 28 days - 8,300 psi
Yield
PRODUCTS
Approximately 0.45 ft3 per 50 lb. bag when mixed with 4.5 quarts of water. At 1” thickness, one 50 lb. bag will cover approximately 5.4 ft2. When one 50 lb. bag is mixed with 4.5 quarts of water & 25 lbs. of 3/8” pea gravel, yield is approximately 0.63 ft3 .
70- FOUNDATION
• Grouting applications that require precision alignment. • Large, tight clearance areas requiring a highly fluid pumpable grout to fill entire void. • Structural grouting of steel & precast columns & beams. • Machinery, equipment and pump baseplates. • Crane rails. • Grouting anchors, dowels, rods, bolts and inserts. • Grouting post-tension cables and cable anchorages.
Technical Data & Specifications
60-PRECAST & TILT-UP
Atlas Hi Flow Grout is a high strength, highly fluid, non-shrink, non-metallic precision grout composed of specially graded natural aggregates, quality cements and proprietary admixtures. Hi Flow Grout provides high compressive strength for applications ranging from damp-pack to fluid, and has a long working time to meet difficult requirements for the most demanding job conditions. This structural grout is very easy to pump.
50-FLATWORK ACCESSORIES
ATLAS HI-FLOW GROUT Non-Shrink, Non-Metallic, High Flow, Precision Cement-Based Grout Description
30-ATLAS TECH PRODUCTS
Uses
Features of Atlas Hi-Flow Grout Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.30.10560
80- TOOLS & PLACING
• High fluidity for ease of pumping and placing for precise grouting applications. • High compressive strength for dynamic load stability. • Extended working time for easy placement. • Non-metallic, will not stain or rust. • Non-gas forming. • Non-corrosive, does not contain calcium chloride.
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
111
Contractor Committed.
ATLAS ULTIMATE HP GROUT
High Performance, High Early & Ultimate Strength, Non-Shrink, Non-Metallic Cement-Based Precision Grout
Features of Atlas Ultimate HP Grout
Description Atlas Ultimate HP Grout is a high performance, high early & ultimate strength, non-shrink, non-metallic precision structural grout composed of superior natural aggregates, cements and admixtures. Ultimate HP Grout exhibits extremely high compressive strength to permanently support and transfer heavy structural loads. This superior grout may be mixed at any consistency from plastic to fluid, and it does not contain chlorides or any other corrosive materials.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Non-Shrink Grouts
• High early and ultimate compressive strength for less equipment downtime, earlier job completion, and maximum load stability. • Excellent fluid consistency for ease of pumping and placing for precision grouting applications. • Extended working time for easy placement. • Greater density than other non-metallic grouts. • Resistant to high heat and thermal shock. • Non-metallic, will not stain or rust. • Non-corrosive, does not contain calcium chloride. • Non-bleeding and non-segregating. • Excellent adhesion to concrete and steel. • Can be molded and shaped.
Technical Data & Specifications ASTM C-1107, Grades A, B & C AASHTO T-260 Working Time (730F): 20-30 minutes Initial Set Time: approx. 45 minutes Compressive Strength (Flowable): 1 day - 5,000 psi 3 days - 8,500 psi 7 days - 9,300 psi 28 days - 12,000 psi Atlas Ultimate HP Grout was an ideal grout for the columns on this roller coaster ride at Sea World in San Diego, CA. This grout was chosen because of its high flowability and high early and ultimate compressive strength.
Uses • Grouting applications that require a high early and/or ultimate compressive strength. • Grouting applications that require precision alignment. • Structural grouting of steel & precast columns & beams. • Machinery, equipment and pump baseplates. • Crane rails. • Grouting anchors, dowels, rods, bolts and inserts. • Power plants, water treatment plants, manufacturing facilities, amusement park rides, or any other heavy repetitive loading applications.
ATLAS N-A GROUT
Non-Aggregate, Highly Flowable, Non-Shrink , Non-Metallic Grout
Description Atlas N-A Grout is a special blend of high quality cements and admixtures to provide a non-aggregate, high flow, high strength, non-shrink, non-metallic precision grout. N-A Grout is a unique formulation that may be pumped through extremely tight clearance areas and over large distances. This easy to use grout demonstrates high compressive and flexural strengths for maximum grouting performance. N-A Grout provides high fluidity and a long working time to meet tough requirements for the most demanding job conditions.
Yield Approximately 0.43 ft3 per 50 lb. bag when mixed with 4.0 quarts of water. At 1” thickness, one 50 lb. bag will cover approximately 5.2 ft2. When one 50 lb. bag is mixed with 4.0 quarts of water & 25 lbs. of 3/8” pea gravel, yield is approximately 0.61 ft3 .
Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.30.11060
Read Product Data Sheet & MSDS prior to use.
Uses • Grouting large, extremely tight clearane areas that require a grout with no sand for high fluidity and ease of pumping. • Structural grouting of columns, beams and concrete piles. • Grouting anchors, dowels, rods, bolts and inserts. • Grouting post-tension cables, tendons, and cable anchorages. Packaging 50 lb. bag (63 bags per pallet) 3,000 lb. Supersack
Read Product Data Sheet & MSDS prior to use.
112
www.atlasform.com
Product Code
Concrete Patching Materials
Serving Concrete Customers Since 1980.
Fast-Setting, Multi-Use, Concrete Patching Material
Description
• Concrete pipe and other precast concrete products. • Patching concrete columns, walls and beams. • Curbs, sidewalks, driveways, steps & manholes. • Large concrete cracks. • Vertical, overhead and horizontal applications. • Interior, exterior, above or below grade applications. • Repairs from featheredge to 1” thick per lift.
Technical Data & Specifications Set Time (730F): Initial - 5 minutes Final - 20 - 30 minutes Compressive Strength: 1 day - 4,300 psi 3 days - 5,000 psi 28 days - 6,800 psi
30-ATLAS TECH PRODUCTS
Uses
• Rapid-setting to provide a quick concrete repair. • High early strength; reaches 4,000 psi in 24 hours. • Smooth “putty-like” consistency; ideal for vertical and overhead applications. • Can be molded, shaped, sanded and shaved. • Can be featheredged (for non-traffic bearing). • Available in a standard gray or light gray color. • One-component; just add water.
20-FORMING ACCESSORIES
Atlas Tech Patch 5 is a rapid-setting, ready to use, concrete repair material for general purpose patching and restoration. This portland cement-based patching material is formulated with special hardeners, aggregates and set accelerators to repair, resurface and restore concrete surfaces. Tech Patch 5 may be used for vertical, overhead and horizontal applications, and is easy to shape and shave to match existing concrete surfaces. Tech Patch 5 develops twice the strength of typical concrete and provides good resistance to freeze/thaw cycles and weathering.
Features of Atlas Tech Patch 5
10-FORMING & SHORING
ATLAS TECH PATCH 5
Yield Approximately 0.54 ft3 per 50 lb. bag when mixed with 3.5 quarts of water. At 1/4” (0.64 cm) thickness, one 50 lb. bag will cover approximately 26 ft2. Product Code 30.32.10060
40-BAR SUPPORTS
Packaging 50 lb. bag (63 bags per pallet)
Read Product Data Sheet & MSDS prior to use.
Fast-Setting, Multi-Use, Concrete Patching Material
Description
Technical Data & Specifications Set Time (730F): Initial - 15 - 20 minutes Final - 30 - 40 minutes Compressive Strength: 1 day - 4,000 psi 3 days - 4,900 psi 28 days - 6,500 psi
PRODUCTS
Yield Approximately 0.54 ft3 per 50 lb. bag when mixed with 3.5 quarts of water. At 1/4” (0.64 cm) thickness, one 50 lb. bag will cover approximately 26 ft2.
Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.32.10560
80- TOOLS & PLACING
• Concrete pipe and other precast concrete products. • Patching concrete columns, walls and beams. • Curbs, sidewalks, driveways, steps & manholes. • Large concrete cracks. • Vertical, overhead and horizontal applications. • Interior, exterior, above or below grade applications. • Repairs from featheredge to 1” thick per lift.
• Rapid-setting to provide a quick concrete repair. • High early strength; reaches 4,000 psi in 24 hours. • Smooth “putty-like” consistency; ideal for vertical and overhead applications. • Can be molded, shaped, sanded and shaved. • Can be featheredged (for non-traffic bearing). • Available in a standard gray or light gray color. • One-component; just add water.
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
70- FOUNDATION
Uses
Features of Atlas Tech Patch 20
60-PRECAST & TILT-UP
Atlas Tech Patch 20 is a rapid-setting, ready to use, concrete repair material for general purpose patching and restoration. This portland cement-based patching material is formulated with special hardeners, aggregates and set accelerators to repair, resurface and restore concrete surfaces. Tech Patch 20 may be used for vertical, overhead and horizontal applications, and is easy to shape and shave to match existing concrete surfaces. Tech Patch 20 develops twice the strength of typical concrete and provides good resistance to freeze/thaw cycles and weathering.
50-FLATWORK ACCESSORIES
ATLAS TECH PATCH 20
113
Contractor Committed.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Structural Concrete Repair Materials
ATLAS TECH-H2
Two-Component, High Strength, Polymer Modified, Cement Based, Concrete Repair Mortar with an Integral Corrosion Inhibitor
Description Atlas Tech-H2 is a polymer modified, cement-based, two-component, fast-setting concrete repair mortar. This high performance structural repair mortar provides excellent durability and superior adhesion for horizontal concrete patching and overlays. Tech-H2 provides excellent workability and is formulated with Ferrolok, a penetrating corrosion inhibitor that helps prevent deterioration caused by chlorides, moisture and other harmful materials. Tech-H2 cures to a concrete gray color to blend with surrounding concrete surfaces and is ideal for areas that are subject to heavy traffic, abrasion and harsh weather.
Uses • Heavy-duty concrete patching and overlays. • Trowelable or “Form & pour” applications; Adjust H2 liquid polymer to acheive desired consistency. • Horizontal surfaces on, above and below grade. • Structural repair applications such as airport runways, parking garages, warehouse floors, manufacturing plants, maintenance facilities, loading docks, walkways, bridges, tunnels, driveways and ramps. • Surfaces subject to freeze/thaw cycles. • Repairs up to 1” neat; up to 4” per lift extended with aggregate. Available in a “H2 Fine” formualtion for easy featheredge application. • Interior and exterior applications.
Atlas Tech-H2 is a high strength polymer modifed concrete repair that will withstand extreme traffic and harsh weather. It can accept walking traffic in less than 2 hours of application, heavy traffic within 4 - 6 hours. Tech-H2 worked excellent for the Marines to repair spalled areas on this military base in Southern California.
Features of Atlas Tech-H2 • Simple to use, fast-setting, labor saving concrete repair system. • Excellent resistance to heavy taffic and abrasion. • Fast-setting repair; foot traffic in less than 2 hours, heavy traffic in 6 hours. • Easy to trowel and screed. • High early compressive and flexural strengths. • Does not form a vapor barrier. • Thermal expansion is similar to concrete for maximum service life. • Excellent freeze/thaw resistance. • Pre-measured components. Enhanced with a liquid polymer to improve adhesion and durability. • Formulated with Ferrolok, a penetrating corrosion inhibitor to help prevent future deterioration. • Consistent color match to existing concrete.
Atlas Tech-H2 is very easy to mix and may be placed with a trowel or screed. This versatile repair material may be mixed to different consistencies to suite specific project requirements. Cures to a concrete gray color to blend with surrounding concrete surfaces.
Yield Approximately 0.43 ft3 per unit - 50 lb. bag mixed with 1 gallon of H2 Bond. At 1/4” thickness, one unit will cover approximately 20 ft2 . Extended: Approximately 0.58 ft3 per unit extended with 25 lbs. 3/8” pea gravel. At 1” thickness, one extended unit will cover 7 ft2.
Technical Data & Specifications Set Time (730F): Initial - 20 - 30 minutes Final - 45 - 60 minutes Bond Strength (28 days): 3,800 psi Flexural Strength (28 days): 2,500 psi Compressive Strength: 1 day - 2,800 psi 3 days - 3,900 psi 7 days - 5,200 psi
Packaging
Product Code
1 gal. jug
30.25.10520
H2 50 lb. bag (63 bags per pallet)
30.32.11060
H2 Fine 50 lb. bag (63 bags per pallet)
30.32.11160
Read Product Data Sheet & MSDS prior to use.
114
www.atlasform.com
Serving Concrete Customers Since 1980.
Concrete Patching Materials
Heavy Duty, One-Component Structural Concrete Patching Material
Description
Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.32.12560
Read Product Data Sheet & MSDS prior to use.
Meets ASTM C-928 specification. Set Time (730F): Working - 14 -16 minutes Final - 28 - 32 minutes Compressive Strength: 3 hour - 3,000 psi 1 day - 5,600 psi 7 days - 6,100 psi 28 days - 7,000 psi
Yield Approximately 0.43 ft3 per 50 lb. bag when mixed with 4.5 quarts of water. At 1/2” thickness, one 50 lb. bag will cover approximately 10 ft2. Extended: Approximately 0.58 ft3 per unit extended with 15 lbs. 3/8” pea gravel. At 3” thickness, one extended bag will cover approximately 2.3 ft2.
50-FLATWORK ACCESSORIES
ATLAS TECH DOT PATCH
Very Fast Setting, Heavy-Duty, Flowable Concrete Repair Mortar For Traffic Bearing Applications
Description
Technical Data & Specifications Meets ASTM C-928 specification. Set Time (730F): Working - 8 - 10 minutes Final - 15 - 20 minutes Compressive Strength: 1 hour - 3,000 psi 1 day - 5,600 psi 7 days - 6,050 psi 28 days - 8,000 psi
60-PRECAST & TILT-UP
Atlas Tech DOT Patch is a fast-setting, heavy-duty, easy to use concrete pavement repair material. This one-component, flowable concrete patch develops high early strength so repair area has minimal downtime. Tech DOT Patch sets in 15 - 20 minutes and will accept traffic within 1 - 2 hours. Designed for horizontal, exterior and interior applications, Tech DOT Patch is an ideal repair material for areas subjected to heavy traffic and freeze/thaw cycles.
40-BAR SUPPORTS
• Ideal for patching and repairing concrete highways, bridge decks, parking structures & ramps, airport runways, loading docks and warehouse & industrial floors or other heavy duty applications. • Structural repair for walls, columns & beams where a trowable high strength material is required. • Repairs up to 3” deep neat; or add pea gravel for deeper repairs. • Interior, exterior, horizontal and vertical applications.
Technical Data & Specifications
30-ATLAS TECH PRODUCTS
Uses
•Develops high early strength. Reaches 3,000 psi compressive strength within 3 hours of set. • Provides a heavy-duty, traffic-bearing surface. • Allows for minimal downtime; traffic can be allowed on surface within 2-3 hours. • Excellent bond strength and flexural properties to provide a long lasting repair that will withstand freeze/thaw cycles and harsh weather environments. • Thermal expansion is similar to concrete for long-term durability and service life. • Cures to a gray color to closely blend with existing concrete. • One-component; just add water.
20-FORMING ACCESSORIES
Atlas Pro-1 Patch is a fast-setting, high performance, easy to use structural concrete repair material. This onecomponent, trowelable concrete patch develops high compressive strength, bond strength and flexural properties to hold up to heavy traffic and freeze/thaw cycles. Pro-1 Patch has been designated for exterior horizontal traffic bearing applications, but also performs well for structural patching of walls, columns, beams or other heavy duty concrete repairs. Pro-1 Patch offers good resistance to oils, de-icing salts and other chemicals to help prevent future corrosion and additional repairs.
Features of Atlas Pro-1 Patch 10-FORMING & SHORING
ATLAS PRO-1 PATCH
Yield
Uses
Product Code 30.32.12060
80- TOOLS & PLACING
• Rapid-setting, high early strength. Reaches 3,000 psi compressive strength only 1 hour after set. • Provides a heavy-duty, traffic-bearing surface. • Provides minimal downtime of repair area. Will be ready for traffic within 1 - 2 hours of placement. • One-component; just add water.
Packaging 50 lb. bag (60 bags per pallet)
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
PRODUCTS
Features of Atlas Tech DOT Patch
Approximately 0.41 ft3 per 50 lb. bag when mixed with 3.0 quarts of water. At 1” thickness, one 50 lb. bag will cover approximately 5 ft2. Extended: Approximately 0.58 ft3 per unit extended with 25 lbs. 3/8” pea gravel. At 1” thickness, one extended bag will cover approximately 7 ft2.
70- FOUNDATION
• Ideal for patching and repairing concrete highways, bridge decks, parking structures, airport runways, loading docks and warehouse & industrial floors. • Flowable mortar for “form & pour” applications. • Full-depth structural repairs from 1/2” - 6” deep. • Grout and anchor dowels, pins and bolts. • Horizontal, exterior and interior applications.
115
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Concrete Repair Materials
Contractor Committed.
ATLAS E-PRO PATCH 100% Solids, High Strength, Low-Modulus, Non-Shrink, Multi-Purpose Epoxy Patching Mortar
Description Atlas E-Pro Patch is a three-component, 100% solids, high strength, low modulus, non-shrink, multi-purpose polymer concrete patching mortar for concrete repair. E-Pro Patch is a convenient pre-packaged repair system that consists of a high quality epoxy resin, curing agent and an engineered blend of graded aggregates to provide a superior concrete patching material. This moisture tolerant epoxy mortar cures rapidly for minimum downtime of traffic areas. This semi-rigid epoxy formula allows for excellent shock absorption when exposed to heavy traffic, abrasion and freeze-thaw cycles.
Uses • Concrete patching for bridge decks, parking structures, industrial floors, airport runways, loading docks, piers, or other concrete surfaces subject to heavy traffic, abrasion, thermal movements and chemical attack. • Expansion joint nosing repairs. • Low-modulus concrete repair for spalls. • Interior or exterior applications. Packaging
Product Code
0.5 ft3 unit (1/2 Gal A. 1/2 Gal B & 60 lb. bag of aggregate)
30.32.17580
2.0 ft3 unit (1/2 Gal A. 1/2 Gal B & 4 - 60 lb. bags of aggregate)
30.32.17585
ATLAS TECH-TOP Self-Leveling Traffic-Bearing Floor Topping for Interior Applications
Description Atlas Tech-Top is a heavy-duty, cement-based, nonshrinking, self-leveling floor topping designed to produce a durable, traffic-bearing surface. This one-component product is a free-flowing pumpable material that is easy to apply and requires minimal labor and installation time. Tech-Top provides a walkable surface within 4 hours of application and will accept light traffic after 24 hours. Also available in a white color, which provides an excellent base material for application of concrete stains.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
Uses • Produce a level traffic-bearing floor topping over new or existing concrete surfaces. • Level concrete floors, ceramic tile, terrazzo and wooden floors. • Resurface rough, old, unlevel or poorly finished concrete surfaces. • Interior applications. • New or old concrete surfaces. • Ideal for industrial floors, offices, schools, hospitals, restaurants, and residential floor surfaces that will be exposed to traffic. • Applications from featheredge to 1” neat; up to 4” per lift extended with aggregate.
116
Packaging
Product Code
50 lb. bag
30.35.11560
Features of Atlas E-Pro Patch • High-performance and easy to use polymer concrete patching mortar. • Durable mortar that provides excellent protection from heavy traffic and abrasion. • Low-modulus for excellent shock absorption and thermal movement. • Excellent chemical bond to the concrete substrate. • High early compressive and tensile strengths; cures rapidly for minimal downtime of repaired area. • Moisture tolerant before and after cure; allows for application on both dry or damp surfaces. • Withstands freeze/thaw cycles. • More permanent repair than cement-based patches. • Pre-packaged system is safe and easy to mix. • Non-flammable. • Low odor; may be used for interior or exterior applications. • Compatible with E-Pro Overlay. • Proven field performance.
Technical Data & Specifications Meets USDA specifications for use in food processing areas. VOC Compliant Gel Time (60 g mass, 730F): 20 - 30 minutes Compressive Strength: 3 hours - 4,300 psi 1 day - 9,000 psi Read Product Data Sheet & MSDS prior to use.
Features of Atlas Tech-Top • Self-leveling topping produces a level, hard and traffic-bearing surface with minimal labor and installation time. • Heavy-duty topping holds up to heavy walking traffic and vehicle traffic. • Hardens quickly to provide a walkable surface within 4 hours of application and light traffic after 24 hours. • Excellent bond strength to properly prepared surfaces. • Easy to mix and place; pumpable. • Cures to a concrete gray color. • Non-shrinking, non-dusting; does not contain gypsum.
Technical Data & Specifications Working Time (730F): 15 - 25 minutes Set Time: Initial - 60 - 70 minutes Final - 1.5 - 2.0 hours Compressive Strength: 1 day - 3,100 psi 7 days - 3,500 psi 28 days - 7,200 psi
Yield Approximately 0.43 ft3 per 50 lb. bag when mixed with 4.5 quarts of water. At 1/4” thickness, one 50 lb. bag will cover approximately 21 ft2. Extended: Approximately 0.55 ft3 per unit extended with 15 lbs. 3/8” pea gravel. At 1” thickness, one extended unit will cover approximately 6.5 ft2. Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
Self-Leveling Toppings
Serving Concrete Customers Since 1980.
Concrete Resurfacing Material for Interior or Exterior Applications
Description
• One component, just add water. • Formulated with dry polymers to improve workability and increase bond to substrate. • Withstands foot and light vehicular traffic. • Fast turn-around, accepts foot traffic in 2-3 hours and, light vehicular traffic in 6-8 hours. • Cures to a light gray concrete color. • Will accept concrete stain treatments. • Freeze thaw resistant. • Easy to apply.
Uses Technical Data & Specifications Working Time (730F): 30 minutes Set Time: Initial - 45 minutes Final - 1.0 hours Compressive Strength: 1 day - 3,100 psi 28 days - 5,000 psi
30-ATLAS TECH PRODUCTS
• Re-surface concrete that is worn, pitted or spalled. • Traffic bearing applications. • Exterior or interior applications. • Horizontal or vertical applications. • New or old concrete surfaces. • Ideal for plazas, patios, parking decks, walkways, driveways, garage floors, and other residential and commercial concrete surfaces.
Yield Packaging 50 lb. bag (60 bags per pallet)
ATLAS TECH-TOP-EXT Self-Leveling Traffic-Bearing Floor Topping for Exterior Applications
Description
Yield Approx. 0.52 ft3 per 50 lb. bag when mixed with 4.0 quarts of water. At 1/4” thickness, one 50 lb. bag will cover approximately 25 ft2. Extended: Approx. 0.62 ft3 per unit extended with 25 lbs. 3/8” pea gravel. At 1/2” thickness, one extended unit will cover approximately 14 ft2. Packaging
Product Code
PRODUCTS
Read Product Data Sheet & MSDS prior to use.
Working Time (730F): 15 - 25 minutes Set Time: Initial - 60 - 70 minutes Final - 1.5 - 2.0 hours Compressive Strength: 1 day - 3,400 psi 7 days - 4,400 psi 28 days - 5,200 psi
70- FOUNDATION
• Produce a level traffic-bearing floor topping over new or existing concrete surfaces. • Level concrete slabs, ceramic tile, terrazzo and wooden floors. • Resurface rough, old, unlevel or poorly finished concrete surfaces. • Exterior or interior applications. • New or old concrete surfaces. • Ideal for loading docks, parking decks, garage floors, industrial floors, patios, walkways, driveways, or other surfaces that will be exposed to traffic and weather. • Applications from featheredge to 1/2” neat; up to 1-1/2” per lift extended with aggregate.
Technical Data & Specifications
60-PRECAST & TILT-UP
Uses
• Self-leveling topping produces a level, hard and traffic-bearing surface for exterior or interior applications. • Requires minimal labor and installation time. • Hardens quickly to provide a walkable surface within 4 hours of application and light traffic after 24 hours. • Cures to a concrete gray color. • Non-shrinking, non-dusting; does not contain gypsum.
50-FLATWORK ACCESSORIES
Atlas Tech-Top EXT is a heavy-duty, cement-based, nonshrinking, self-leveling floor topping designed to produce a durable, traffic-bearing surface for exterior or interior applications. This one-component product is a free-flowing pumpable material that is easy to apply and requires minimal labor and installation time. Tech-Top EXT provides a walkable surface within 4 hours of application and will accept light traffic after 24 hours.
Features of Atlas Tech-Top EXT
40-BAR SUPPORTS
Approx. 30-60 ft2 per 40 lb. bag when mixed with 3.0 quarts of water and applied at 1/8” to 1/16” thick.
Product Code
20-FORMING ACCESSORIES
Atlas Tech-Top MT is cement-based polymer modified micro-topping for concrete surfaces. Teck-Top MT is a thinly applied resurfacer that closely resembles the look of natural concrete and will provide a new wearing surface over damaged concrete. Atlas Tech-Top MT is available in 2 grades, MT-F for the fine smoother finishes, and MT-R for coarser or broom finish textures.
Features of Atlas Tech-Top MT
10-FORMING & SHORING
ATLAS TECH-TOP MT
50 lb. bag (60 bags per pallet)
80- TOOLS & PLACING
www.atlasform.com
117
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Self-Leveling Underlayment
Contractor Committed.
ATLAS TECH-LEVEL PREMIER Premium Self-Leveling Underlayment for Interior Applications
Description Atlas Tech-Level Premier is a high-performance, cement-based, self-leveling floor underlayment designed to produce a smooth, level and hard surface prior to the placement of floor coverings. This one-component, non-shrink underlayment exhibits superior flowability for an extremely easy installation. Tech-Level Premier will reduce labor costs, minimize placement time and produce a new substrate that will quickly accept installation of resilient flooring, carpet, ceramic tile, wood flooring, or other traffic bearing coverings. This fast-track underlayment provides a walkable surface within 4 hours of application and will accept floor coverings after 14 hours.
Prior to the application of Atlas Tech-Level Premier, the substrate is primed with an Atlas approved primer, such as Atlas Tech-Bond or Inter-Bond. The primer is easily applied with a broom and assures a good bond of Tech-Level Premier.
Uses • Create a smooth, level and hard surface prior to the placement of floor coverings. • Level concrete floors, ceramic tile, terrazzo and wooden floors. • Resurface rough, unlevel or poorly finished concrete. • Interior, above and below grade applications. • New or old concrete surfaces. • Ideal for offices, schools, hospitals, restaurants, and residential floor surfaces that are to be resurfaced with carpet, tile or other floor coverings. • Applications from featheredge to 1” neat; up to 4” per lift extended with aggregate.
Features of Atlas Tech-Level Premier • Produces a smooth, level and hard surface with minimal labor and installation time. • Cures quickly to allow for traffic in 4 hours, and for placement of floor coverings after 14 hours. • Formulated with high performance polymers for improved workability & increased bond strength. • Easy to mix and place; pumpable. • One-component; just add water. • Non-shrinking and non-dusting. • Compatible with most flooring adhesives.
Atlas Tech-Level Premier is a self-leveling material that can be poured from a bucket or placed with a pump. This free-flowing material requires minimal labor, as the product fills low spots to create a level, smooth and hard surface prior to the placement of floor coverings.
Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.35.10060
ChemGrout CG-502 Pump is available from Atlas on a rental basis.
Technical Data & Specifications Working Time (730F): 15 - 20 minutes Set Time: Initial - 30 - 40 minutes Final - 1.0 - 1.5 hours Compressive Strength: 1 day - 2,600 psi 7 days - 3,800 psi 28 days - 4,500 psi
Yield Approximately 0.51 ft3 per 50 lb. bag when mixed with 4.5 quarts of water. At 1/4” thickness, one 50 lb. bag will cover approximately 24 ft2. Extended: Approximately 0.60 ft3 per unit extended with 15 lbs. 3/8” pea gravel. At 1” thickness, one extended unit will cover approximately 7.0 ft2.
118
ChemGrout’s high-efficiency sprayer/finisher is ideal for pouring underlayments or spraying cementitous coatings. The two 45-gallon mixing tanks, large holding hopper and centrally located controls allow continuous production with a single operator. The ChemGrout CG-502 is the perfect choice along with Atlas Tech Level Premier when you have a large underlayment job!
www.atlasform.com
Concrete Repair Materials
Serving Concrete Customers Since 1980.
Cement -Based, Thin Patching Underlayment for Interior Applications
Features of Atlas Feather Coat
Description
ATLAS DURA-MORTAR High Performance, Flowable, Shrinkage Compensated, Structural Repair Mortar with an Integral Corrosion Inhibitor
Packaging
Product Code
10 lb. bag
30.32.13551
Uses • Ideal for patching and repairing concrete bridges, parking structures, highways, airport runways, loading docks, warehouse & industrial floors, tunnels, piers, docks and dams. • Free-flowing mortar for “form & pour” applications or for hard to reach areas. • Areas subjected to heavy traffic, abrasion, harsh weather or freeze/thaw cycles. • Full-depth structural repairs from 3/4” - 10” deep.
Features of Atlas Dura-Mortar • Very high compressive, flexural and bond strengths for a high performance structural repair with many applications. • High early strength - reaches 8,000 psi in 24 hours. • Extremely dense material formulated with Ferrolok, a integral corrosion inhibitor to reduce deterioration caused by chlorides, carbon dioxide & contaminants. • Formulated with shrinkage compensating admixtures. • Thermal expansion is similar to concrete for longterm durability and service life.
60-PRECAST & TILT-UP
Atlas Dura-Mortar is a high-performance, flowable, dense and resilient concrete repair mortar that exhibits high compressive strength, excellent flexural properties and superior shear bond strength. This free-flowing mortar is easy to place, has an extended set time, and is ideal for “form & pour” applications that require deep repairs for deteriorated or spalled horizontal, vertical or overhead surfaces. Dura-Mortar contains Ferrolok, an integral corrosion inhibitor that will reduce corrosion in the repaired area and adjacent concrete to provide a long service life of repair.
Approximately one 10 lb. bag of Feather Coat will cover approximately 33 ft2 at 1/8” thickness. Depending on the condition of the substrate, one bag will typically cover 150-200 ft2.
50-FLATWORK ACCESSORIES
Description
Yield
40-BAR SUPPORTS
• Provide a smooth, hard & level surface over rough, damaged or unlevel concrete prior to the installation of floor coverings. • Patch over concrete, terrazzo, wood, tile, VCT or cutback adhesives. • Ideal for fast-track projects where floor coverings need to be installed as soon as possible. • Applications from featheredge to 1/4” thick per lift. • Interior applications.
30-ATLAS TECH PRODUCTS
Uses
• High polymer formulation that contains no sand to provide an extremely smooth consistency and excellent workability. • Fast drying to allow installation of floor coverings as soon as the patch is dry; typically within 15-20 minutes of application. • True featheredge application up to 1/4” per lift. • Excellent bond strength to concrete surfaces; no primer necessary. • Simple to use one-component; just add water. • Easy to trowel-apply with excellent coverage rates.
PRODUCTS
Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.32.15060
www.atlasform.com
80- TOOLS & PLACING
Read Product Data Sheet & MSDS prior to use.
Meets ASTM C-928 specification. Set Time (730F): Initial - 35 - 45 minutes Final - 80 - 90 minutes Bond Strength (7 days): 4,000 psi Compressive Strength: 1 day - 8,000 psi 7 days - 9,600 psi 28 days - 11,800 psi
70- FOUNDATION
Technical Data & Specifications
Atlas Dura-Mortar was used to repair this 14’ tall x 14” deep void; the application took less than 2 hours, and forms were stripped the next morning. The surface was then ready to accept waterproofing.
20-FORMING ACCESSORIES
Atlas Feather Coat is an innovative, high performance trowelable underlayment that is used as a skim coat to provide a smooth surface and level floor prior to the installation of floor coverings. This polymer modified material may be used for interior applications on concrete, terrazzo, wood, ceramic tile, VCT and also over non-water soluble cutback adhesives on existing concrete. Feather Coat is fast-drying and will be ready to accept installation of flooring materials, such as carpet, tile, VCT & sheet vinyl as soon as patch is dry, which is typically within 15-20 minutes.
10-FORMING & SHORING
ATLAS FEATHER COAT
119
Contractor Committed.
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Concrete Patching Materials
ATLAS V/O-1 MORTAR
One-Component, High Strength, Polymer Modified Concrete Repair with a Corrosion Inhibitor for Vertical & Overhead Applications
Description Atlas V/O-1 Mortar is a high strength, one-component, polymer modified, cement-based, fast-setting, non-sag, mortar for vertical or overhead structural concrete repairs. This high-performance patching material is easily placed on vertical or overhead surfaces without the need for forms to properly repair parking structures, bridge structures, docks, piers, etc. This concrete repair material is specially formulated with Ferrolock, a penetrating corrosion inhibitor that helps prevent future deterioration caused by chlorides, moisture and other harmful materials. V/O-1 Mortar cures to a concrete gray color to blend-in with surrounding concrete surfaces. This durable repair mortar has excellent resistance to harsh weather conditions and freeze/thaw cycles.
Uses • Structurally repair vertical, overhead or horizontal concrete structures. • Ideal for repairing deteriorated concrete in parking structures, water treatment plants, bridge structures, tunnels, dams, docks, piers, ramps, and all concrete pipes, walls, ceilings & columns. • Surfaces subject to freeze/thaw cycles. • Repairs from 1/8” to 2” per lift. • Interior or exterior applications, above or below grade.
50-FLATWORK ACCESSORIES
Read Product Data Sheet & MSDS prior to use.
ATLAS STRUCTURAL REPAIR MORTAR V & O
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Two-Component, High Strength, Polymer Modified, Cement-Based, Concrete Repair Mortar for Vertical & Overhead Applications
Features of Atlas V/O-1 Mortar • Non-sag consistency is easy to place on vertical or overhead surfaces without the use of forms. • High bond strength for excellent adhesion and a successful, long-lasting, durable repair. • High early, compressive, flexural and tensile strengths. • Formulated with Ferrolock, an integral corrosion inhibitor. • Thermal expansion is similar to concrete for maximum service life. • Withstands harsh weather and freeze/thaw cycles. • Easy to use, just add water. • Consistent color match to surrounding concrete.
Technical Data & Specifications Working Time (730F): 20 minutes Set Time: Initial - 40-50 minutes; Final - 90-100 minutes Compressive Strength: 1 day - 1,700 psi 7 days - 4,200 psi 28 days - 5,400 psi
Yield Approximately 0.43 ft3 per 50 lb. bag mixed with 9.5 pints of water. At 1/4” thickness, one 50 lb. bag will cover approximately 20 ft2 . Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.32.15560
Features of Structural Repair Mortar V & O
Atlas Structural Repair Mortar V & O is a high strength, two-component, polymer modified, cement-based, non-sag, fast-setting concrete repair mortar. This high-performance mortar is easily placed on vertical and overhead surfaces without the use of forms. Structural Repair Mortar V & O is a unique non-shrink formulation that is very durable and will withstand harsh weather conditions and freeze/thaw cycles.
• Simple to use, fast-setting, labor saving concrete repair system. • Non-sag consistency is easy to place on vertical or overhead surfaces. • Excellent adhesion and high early strength for quick and successful concrete restoration projects. • High early compressive and flexural strengths. • Thermal expansion is similar to concrete for maximum service life. • Pre-measured components. Enhanced with a liquid polymer to improve adhesion and durability.
Uses
Yield
• Structurally repair vertical, overhead & horizontal concrete and masonry surfaces. • Ideal for restoration of parking garages, water treatment plants, bridges, tunnels, dams, docks, piers, concrete pipes, walls, ceilings & columns. • Repairs from 1/8” to 2” per lift. • Interior, exterior, above and below grade applications.
Approximately 0.41 ft3 per unit, consisting of one 50 lb. bag mixed with 1 gallon of Structural Repair Liquid polymer. At 1/4” thickness, one 50 lb. bag will cover approximately 20 ft2.
Description
Packaging 50 lb. bag & 1 gal. jug
Read Product Data Sheet & MSDS prior to use.
120
www.atlasform.com
Product Code 30.32.15860
Serving Concrete Customers Since 1980.
Structural Concrete Repair Materials
Extremely Smooth, High Polymer Resurfacing and Finishing Compound for Vertical Concrete Surfaces
Description
One 10 lb. pail will cover approximately 65 ft2 at 1/16” thickness. Depending on the condition of the concrete surface, one pail will typically cover 100-150 ft2. Product Code
7 lb. pail
30.32.16050
10 lb. bag
30.32.16051
• High polymer formulation that contains no sand to provide an extremely smooth consistency and excellent workability. • Cure to a concrete gray color for exposed concrete surfaces. • Cures quickly to a hard surface to provide a bondable surface for paints and coatings; jobs may be completed in less amount of time. • Excellent bond strength to concrete surfaces. • Simple to use one-component; just add water. • Eliminates surface dusting and sanding. • Easy to trowel-apply with excellent coverage rates. • Does not contain gypsum.
40-BAR SUPPORTS
Packaging
Features of Atlas V/R Patch
30-ATLAS TECH PRODUCTS
Yield
• Provide a smooth and hard surface over damaged, rough or discolored concrete and masonry surfaces. • Repair voids, honeycombs, holes, small cracks, etc. • Ideal for sacking and patching tilt-up panels, precast concrete, concrete walls, columns, beams, etc. • Exposed interior concrete surfaces and exterior surfaces to be painted or coated. • Vertical and overhead applications. • Applications from featheredge to 1” thick. • Interior and exterior applications.
20-FORMING ACCESSORIES
Atlas V/R Patch is an innovative, high performance patching and resurfacing material designed to repair concrete surfaces that are rough, damaged or discolored. V/R Patch is a high polymer, cement based coating that contains no sand to provide an extremely smooth consistency for easy application and maximum product performance. This surface treatment has excellent bond strength and is ideal for rubbing, smoothing and resurfacing vertical or overhead surfaces that have bug holes, voids, spalls, dents, cracks etc. This easyto-use concrete repair product dies quickly to provide a bondable surface for paints and coatings and provide for fast job completion.
Uses 10-FORMING & SHORING
ATLAS V/R PATCH
ATLAS SMOOTHCRETE PLUS Smooth Patching & Resurfacing Material for Concrete Surfaces
• Exceptionally smooth and hard finish. • Excellent workability and creamy smooth consistency. • Excellent bond strength. • Simple to use one-component; just add water. • Already contains dry polymers for superior workability, adhesion and durability. • Jobs may be completed more quickly; pre-packaged material is easy and quick to mix and cures rapidly to provide a bondable surface for paints and coatings. • Long bucket life for ease of application. • Easy to shape and sand; minimal to no surface dusting. • Does not contain gypsum. • Moisture insensitive after curing. • Cures to a concrete gray color to blend with surrounding concrete.
60-PRECAST & TILT-UP
Features of Atlas Smoothcrete Plus
Atlas Smoothcrete Plus is a specially formulated patching and resurfacing material designed for repairing and restoring concrete surfaces. Excellent for rubbing, smoothing and resurfacing horizontal, vertical or overhead surfaces for thin patching applications. Smoothcrete Plus is a unique blend of portland cement, dry polymers and special additives to provide the ultimate smooth-finish patching material. This easy-to-use concrete repair product has excellent bond strength, weather resistance, and provides a bondable surface for paints and coatings.
50-FLATWORK ACCESSORIES
Description
Technical Data & Specifications PRODUCTS
Yield One 50 lb. bag will cover approximately 100 ft2 at 1/16” thickness. Packaging
Product Code
40 lb. bag (63 bags per pallet)
30.32.16558
80- TOOLS & PLACING
• Resurface rough, damaged or discolored concrete and masonry surfaces. • Repair voids, honeycombs, holes, small cracks, etc. • Ideal for patching tilt-up panels and precast concrete. • Provides a smooth and hard surface that may be painted or treated with architectural coatings. • Horizontal, vertical and overhead applications. • Trowelable underlayment for future floor coverings. • Applications from featheredge to 1/8” thick. • Interior and exterior applications.
70- FOUNDATION
Uses
Working Time (730F): 40 minutes Set Time: Initial - 2 hours; Final - 4 - 5 hours Compressive Strength: 1 day - 900 psi 3 days - 1,300 psi 7 days - 2,800 psi 28 days - 3,950 psi
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
121
Contractor Committed.
PRODUCTS
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Concrete Patching Materials
ATLAS TECH-321
Thin patching and Resurfacing Material for Concrete Surfaces
Description Atlas Tech-321 is a specially formulated patching and coating material designed for repairing and restoring concrete surfaces. Formulated with dry polymers, Tech-321 has excellent workability and adhesion to the substrate, and cures to a hard and smooth finished surface. Ideal for rubbing, smoothing and resurfacing all horizontal, vertical or overhead concrete surfaces for thin patching and coating applications. Tech-321 is blended with white and gray portland cement, very fine aggregates and special additives to provide a smooth finish over rough, damaged or discolored concrete. This easy to use, one component product has excellent weather resistance and cures to a concrete gray color to blend with existing surfaces and leave an attractive concrete finish.
Uses • Refinish exposed concrete walls, beams, ceilings, columns, steps, walkways and patios. • Resurface rough, damaged or discolored concrete and masonry surfaces. • Repair voids, honeycombs, holes, small cracks, etc. • Horizontal, vertical and overhead applications. • Applications from featheredge to 1/8” thick. • Interior and exterior applications.
Features of Atlas Tech-321 • Provides a smooth and hard surface that cures to an attractive concrete gray color. • Excellent workability and creamy smooth consistency. • Extended working time. • Excellent bond strength. • Simple to use one-component; just add water. • Easy to shape and sand. • Does not contain gypsum. • Moisture insensitive after curing. • Also available in a white color.
Technical Data & Specifications Working Time (730F): 30 minutes Set Time: Initial - 2 hours; Final - 4 hours Compressive Strength: 1 day - 900 psi 3 days - 1,450 psi 7 days - 2,900 psi 28 days - 4,150 psi
Yield One 50 lb. bag will cover approximately 100 ft2 at 1/16” thickness. Packaging
Product Code
50 lb. bag (63 bags per pallet)
30.32.17060
Read Product Data Sheet & MSDS prior to use.
ATLAS PLUG
Features of Atlas Plug
Fast-Setting Hydraulic Cement to Plug Water Leaks
Description Atlas Plug is a fast-setting hydraulic cement designed to plug fluid leaks and stop water seepage in concrete or masonry surfaces. Atlas Plug is a durable, non-corrosive, non-rusting material that is composed of cement and proprietary admixtures. When mixed with water to a putty consistency, Atlas Plug will set in 2-3 minutes and will last the life of the structure.
Uses • Stop water seepage and fluid leaks through cracks, faults, crevices and holes in concrete and masonry surfaces. • Ideal for concrete pipes, manholes, culverts, storm drains, swimming pools, tunnels, dams, water tanks, sewers, basements, elevator pits, etc. • Underwater applications. • Vertical and horizontal applications. • Interior, exterior, above or below grade applications.
• Very fast-setting to stop water seepage immediately. • Will last the life of the structure. • Will not shrink, corrode, rust or stain. • Sets under water; just hold in place until set. • One-component; just add water.
Technical Data & Specifications Set Time: Initial - 2 minutes; Final - 3 minutes Compressive Strength: 1 day - 4,000 psi 3 days - 5,100 psi 28 days - 6,500 psi
Yield Approximately 0.50 ft3 per 50 lb. pail
Packaging
Product Code
50 lb. pail ( 36 per pallet)
30.32.18061
80- TOOLS & PLACING
Read Product Data Sheet & MSDS prior to use.
122
www.atlasform.com
Cement-Based Waterproof Coating
Serving Concrete Customers Since 1980.
Cement-Based Waterproofing Coating for Concrete & Masonry
Features of Atlas Hydroseal
Description
Uses
Technical Data & Specifications Coverage Smooth Surface 1st Coat: 150 - 200 ft2 per 50 lb. bag 2nd Coat: 300 - 500 ft2 per 50 lb. bag
40-BAR SUPPORTS
Rough Surface 1st Coat: 100 - 200 ft2 per 50 lb. bag 2nd Coat: 200 - 300 ft2 per 50 lb. bag Packaging
Product Code
50 lb. bag (60 bags per pallet)
30.32.18560
30-ATLAS TECH PRODUCTS
• Waterproof concrete, block, brick, stone, stucco and other masonry surfaces. • Interior and exterior applications, above & below grade. • Ideal for foundations, basement and retaining walls, water reservoirs, bridges and tunnels. • Positive and negative side applications.
• Excellent waterproofing properties to prevent moisture damage. • Out-performs paint-type coatings. • Breathable coating allows moisture from the interior to escape without blistering or peeling the coating. • Provides both positive and negative side protection. • Produces a consistent and uniform appearance. • Add fine sand in mix to obtain a desired texture finish. • Conceals mortar joints and hides minor surface defects. • Leaves a bondable surface for architectural coatings. • Rapid-setting speeds job cycle. • Excellent durability in freeze/thaw conditions. • Resists chloride/salt penetration.
20-FORMING ACCESSORIES
Atlas Hydroseal is a cement-based coating material designed to waterproof concrete and masonry surfaces. This protective coating fills and seals the pores and voids in the surface to prevent the migration of moisture and withstand mild hydrostatic pressure. Hydroseal is a single component, non-shrink, breathable coating that is available in a concrete gray color.
10-FORMING & SHORING
ATLAS HYDROSEAL
50-FLATWORK ACCESSORIES
Read Product Data Sheet & MSDS prior to use.
60-PRECAST & TILT-UP
Atlas Hydroseal is easily applied with a soft-bristled broom, brush or trowel to horizontal or vertical surfaces to seal the pores in concrete and masonry surfaces, effectively preventing the migration of moisture and mild hydrostatic pressure.
PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
123
Contractor Committed.
ATLAS TECH-HARD High Performance Mineral Aggregate Dry-Shake Floor Hardener
Uses Description Atlas Tech-Hard is a ready-to-use, high performance, mineral aggregate dry-shake floor hardener designed to provide a more abrasion resistant concrete floor surface. This non-metallic, non-rusting hardener is a specially blended mixture of portland cement, natural silica quartz aggregate and proprietary admixtures. Tech-Hard may be used for interior or exterior applications and will conform to floor flatness specifications. Available in many colors and an energy efficient light reflective formulation.
40-BAR SUPPORTS
Atlas Tech-Hard is efficiently applied with a laser spreader (above) or a mechanical spreader (below) for accurate application rates. This hardener provides a floor that has more than twice the abrasion resistance than a standard 4,000 psi concrete floor.
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
• Concrete floor installations where a more dense and abrasion resistant surface is required. • Ideal for distribution centers, warehouse floors, loading docks, maintenance facilities, industrial plants, aircraft hangars, shopping centers, showroom floors, hospitals, restaurants, etc. • Concrete surfaces subjected to forklift traffic, pallet jacks, tool carts or other vehicles and machinery. • Floors where a designated flatness is specified. • Wherever colorful abrasion resistant floors are required. • Interior and exterior applications.
Features of Atlas Tech-Hard
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Dry-Shake Floor Hardeners
• Provides a concrete floor with twice the abrasion resistance of normal concrete to prolong the serviceable life of the floor. • Reduces surface dusting, spalling and deterioration to minimize maintenance and repair expenses. • Increases density of the surface for greater resistance to liquid penetration and provide for easy cleaning. • Conforms to floor flatness specifications. • Non-rusting formulation for interior or exterior use. • Available in many non-fading colors to provide a longlasting attractive finish. • Light Reflective formulation exceeds 60% reflectivity to reduce energy costs. • Proven performance.
Coverage Coverage will vary depending on the particular traffic volume of the surface: Light Traffic: 0.75 - 1.0 lbs. per ft2 Moderate Traffic: 1.0 - 1.25 lbs. per ft2 Heavy Traffic: 1.25 - 1.5 lbs. per ft2 Colored Floors: 1.5 - 2.0 lbs. per ft2 Light Reflective: 1.5 - 2.0 lbs. per ft2
Packaging
Product Code
50 lb. bag (60 bags per pallet)
PRODUCTS
Colors Natural Gray, Light Gray, Battleship Gray, Terra Cotta, Tile Red, Nile Green, Tan, Brown, Black and Light Reflective (White). See Dry-Shake Floor Hardeners brochure for color samples.
80- TOOLS & PLACING
70- FOUNDATION
A Complete System Atlas offers a complete concrete flooring system to provide the toughness, protection and quality appearance that will impress the most demanding users. Five products to achieve a durable and attractive concrete floor: Atlas Tech-Hard - dry-shake floor hardener Atlas Finish-Film - evaporation retardant Atlas Quantum-Cure - curing compound Atlas Elite-HS - dustproofer/sealer Atlas Epoxy Joint Filler - joint sealant Contact your Atlas representative to discuss how this complete concrete floor system can benefit you and your clients. Read Product Data Sheet & MSDS prior to use.
124
www.atlasform.com
Dry-Shake Floor Hardeners
Serving Concrete Customers Since 1980.
Heavy-Duty Metallic Dry-Shake Floor Hardener
Description
Coverage Coverage will vary depending on the particular traffic volume of the surface: Heavy Traffic: 1.25 - 1.5 lbs. per ft2 Colored Floors: 1.5 - 2.0 lbs. per ft2 Light Reflective: 1.5 - 2.0 lbs. per ft2
Colors of Atlas Tech-Plate Natural Gray, Light Gray, Battleship Gray, Terra Cotta, Tile Red, Nile Green, Tan, Brown, Black and Light Reflective (White). See Dry-Shake Floor Hardeners brochure for color samples. Product Code
50-FLATWORK ACCESSORIES
Packaging 50 lb. bag (60 bags per pallet)
Abrasion Resistance
0.7 0.6 0.5 0.3 0.2 0.1 Metallic Aggregate Mineral Aggregate Hardener: Atlas Tech- Hardener: Atlas TechPlate Hard
10% Silica Fume Concrete
4,000 psi Concrete Treated with Penetrating Liquid Hardener: Atlas EliteHS
4,000 psi Concrete
Read Product Data Sheet & MSDS prior to use.
www.atlasform.com
125
80- TOOLS & PLACING
Iron Aggregate Topping
PRODUCTS
0.4
This chart shows the depth of wear, in inches, of several floor surfaces after 60 minutes of abrasion testing, as tested by guidelines of ASTM C-779, Procedure A.
70- FOUNDATION
Depth of Wear (inches)
60-PRECAST & TILT-UP
0.8
0
40-BAR SUPPORTS
• Concrete floor installations where an extremely more dense and abrasion resistant surface is required. • Ideal for manufacturing facilities, assembly plants, aircraft hangars, loading docks, industrial plants, distribution centers, warehouses, etc. • Concrete surfaces subjected to steel wheel traffic, heavy pin-point loading, forklift traffic, pallet-jacks, tool carts or other vehicles and machinery. • Floors where a designated flatness is specified. • Wherever colorful & extremely abrasion resistant floors are required. • Interior applications (A non-rusting formulation is available for exterior applications).
30-ATLAS TECH PRODUCTS
Uses
• Provides a concrete floor with eight times the abrasion resistance of normal concrete to prolong the serviceable life of the floor. • Reduces surface dusting, spalling and deterioration to minimize maintenance and repair expenses. • Increases density of the surface for greater resistance to liquid penetration and provide for easy cleaning. • Conforms to floor flatness specifications. • Reduces the wear on forklift tires and other vehicles. • Available in many non-fading colors to provide a longlasting attractive finish. • Light Reflective formulation exceeds 60% reflectivity to reduce energy costs. • Proven performance. • Available in a non-rusting formulation for exterior use.
20-FORMING ACCESSORIES
Atlas Tech-Plate is a ready-to-use metallic dry-shake floor hardener designed to provide a more abrasion resistant concrete floor surface for heavy traffic and industrial applications. This heavy-duty hardener is a specially blended mixture of portland cement, well-graded iron aggregates and proprietary admixtures to produce a floor surface with 8 times the abrasion resistance over normal concrete. Tech-Plate may be used for interior applications and will conform to floor flatness specifications. Available in many colors, including an energy efficient light reflective formulation and a non-rusting formulation.
Features of Atlas Tech-Plate
10-FORMING & SHORING
ATLAS TECH-PLATE
Contractor Committed.
EPOXY SYSTEMS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Construction Chemicals
Unitex Complete Systems Unitex offers a complete epoxy application system, from the epoxy material to surface ports, mix nozzles, and application guns.
Pre-Measured Cartridges
Static Mixers
Unitex Quality Unitex epoxies are manufactured under strict quality control requirements to provide contractors with high performance and reliable epoxy materials.
Manual & Pneumatic Dispensing Guns
Unitex Approvals Unitex epoxies are approved by numerous state D.O.T.s across the country, including Caltrans, Nevada, Arizona and Colorado. Also approved by City of Los Angeles. ICC Report #5000.
Bulk Containers
Unitex Cartridge Epoxies
PRODUCTS
Pro-Poxy 100 - Low viscosity, high modulus injection resin; 16.5 oz. cartridge. Pro-Poxy 204 - Medium viscosity, high modulus bonding agent & injection resin; 22 oz. cartridge. Pro-Poxy 300 - Non-sag viscosity, high modulus, anchoring gel or injection gel; 10 oz., 22 oz. or 51 oz. cartridges. Pro-Poxy 300 Fast - Fast-setting, non-sag viscosity, high modulus, anchoring gel or injection gel; 10 oz., 22 oz. or 51 oz. cartridges. Pro-Poxy 400 - Extremely fast-setting, non-sag viscosity, high modulus, epoxy acrylate anchoring gel; 5 oz or 28 oz. cartridges. Pro-Flex - Self-leveling, low modulus (semi-rigid) control joint sealant; 22 oz. cartridge. Pro-Flex Gel - Non-sag viscosity, pick-proof, low modulus (semi-rigid) sealant; 22 oz. cartridge. * - All unitex epoxies also available in bulk packaging. Contact your Atlas representative for more information.
Pro-Poxy 300 / Pro-Poxy 300 Fast Anchoring Epoxy: • Permitted for use in wet or damp holes. • Permitted in severe weathering locations. • Freeze/thaw resistant. • Suitable for seismic conditions. • Allowed at close edge distances. • Allowed at shallow embedments. • Low odor. • For both solid and hollow base materials.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
Ports
126
www.atlasform.com
Serving Concrete Customers Since 1980.
Construction Chemicals
10-FORMING & SHORING
CHEMICALS & CEMENTITIOUS PRODUCTS
Dry-Shake Floor Hardeners Quartz TuffTM - Non-metallic quartz aggregate hardener. Ferro TuffTM - Metallic iron aggregate hardener. Emery TuffTM - 100% pure emery hardener for an extremely hard, non-corrosive and rust-free concrete floor. Contact your Atlas representative for further information on Dayton Superior chemical & cementitious products.
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
Sealers & Coatings Spec Cote - Epoxy floor sealer with increased resistance to chemicals and abrasion. Day-Chem Urethane (J-39) - High performance polyurethane floor coating with superior resistance to chemicals and abrasion. WeatherWorker WB - Water-based siloxane penetrating water-repellent sealer for exposed concrete surfaces. Silane 20 / 40 WB - Water-based silane penetrating sealer for maximum water repellency on exposed concrete surfaces.
Self-Leveling Underlayments LeveLayer ITM - Premium self-leveling underlayment for interior applications. LeveLayer IITM - Self-leveling underlayment for interior applications, lower psi than LeveLayer I. LeveLayer IIITM - Heavy duty self-leveling floor topping for interior applications. LeveLayer IVTM - Heavy duty self-leveling floor topping for exterior applications.
30-ATLAS TECH PRODUCTS
Liquid Hardener, Dustproofer & Sealer Sure-Hard (J-17) - A colorless, odorless water-based solution of reactive chemicals which deeply penetrates concrete surfaces to seal, densify and harden the treated areas. Ideal for concrete floors, as it increases the durability and abrasion resistance of the surface to protect from heavy traffic. The treated surface develops an attractive sheen finish that resists black tire marks and is easy to clean and maintain.
Non-Shrink Grouts & Patching Materials Dayton Superior manufacturers high quality non-shrink cement-based grouts for many different applications, ranging from dry-pack to highly fluid consistencies.
20-FORMING ACCESSORIES
D.O.T. Curing Compounds Dayton Superior manufactures many D.O.T. approved curing compounds for Caltrans, Arizona, Nevada, Colorado and many other states. Clear resins, white resins, clear waxes, white waxes & other special formulations such as poly-alpha-methylstyrene are preapproved and ready for jobsite use.
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
127
Contractor Committed.
DECORATIVE CONCRETE Design-Crete The Design-Crete System changes normal gray concrete surfaces into an exceptional architectural design. A combination of colors and special tools permanently imprint newly placed concrete with authentic textures.
20-FORMING ACCESSORIES
10-FORMING & SHORING
Decorative Concrete
30-ATLAS TECH PRODUCTS
The Design-Crete System provides a textured concrete at a fraction of the cost of comparable natural materials. Detailed stone, brick, wood or tile patterns can be simulated in a variety of colors.
40-BAR SUPPORTS
Color Hardeners Color hardener is a cementitious dry shake material formulated with carefully balanced and blended pigments, uniform and resistant to discoloration. Color hardener increases the density and durability of the concrete surface, reduces dusting, and minimizes maintenance.
50-FLATWORK ACCESSORIES
Color Releases Color release is a pigmented dry powder release for the stamping tools designed to be used when a mottled, antiqued appearance is desired. It is a pigmented bondbreaker, formulated to prevent stamping tools from sticking to the concrete.
PRODUCTS
Stampable Overlay System The Stampable Overlay System is a stampable cementitious topping for beautifying both interior and exterior concrete surfaces. When stamped, Stampable Overlay creates a texture that duplicates a wide range of stamp designs, tile, cut stone, slate, brick, cobblestone and many other textures.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Stamping Tools Stamping tools and mats are molded urethane patterns that impart a pattern and texture to colored concrete surfaces. Stamping tools and mats are imprinted in a variety of patterns and textures for creating architectural hardscapes for interior or exterior concrete. Available in rigid, flexible and texture mats.
128
www.atlasform.com
Decorative Concrete
Serving Concrete Customers Since 1980.
20-FORMING ACCESSORIES
Spray-Rite Enhance the appearance of existing concrete surfaces with the Spray-Rite concrete texturing system. This system can transform plain, damaged, or stained concrete surfaces into an exciting textured finish.
10-FORMING & SHORING
DECORATIVE CONCRETE
30-ATLAS TECH PRODUCTS
This exclusive Spray-Rite system is based on a high-strength cement coating, specifically formulated to resurface existing concrete. It provides a durable, easily maintained and permanent color finish, engineered to withstand temperature extremes and intense sunshine.
40-BAR SUPPORTS
Patina Stain Color Patina stain is a penetrating reactive stain that produces unique color effects in finished concrete surfaces that simulate natural shadings and aged appearance of stone or masonry. The color effect is unique to each stained surface and cannot be duplicated with other materials.
50-FLATWORK ACCESSORIES
Patina Stain may be applied over smooth troweled concrete, gunite, Design-Crete, Spray-Rite, Stampable Overlay, Integral Color, or most masonry surfaces. The color will not chip, crack or wear off like coatings because the stain penetrates and colors both the surface and the substrate.
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
Integral Color System Integral colors are high purity iron oxide pigments. The pigments easily disperse in the concrete batch to produce uniform color for ready-mix applications. Integral colors provide a uniform color and are UV stable providing excellent fade resistance.
80- TOOLS & PLACING
www.atlasform.com
129
GTI COMPOSITE SLAB BOLSTER This lightweight composite slab bolster makes placement of rebar simple and fast. The GTI Slab Bolster is manufactured in 2.5 ft. & 5 ft. lengths and is available in multiple heights, ranging from 3/4” to 4”. The GTI Slab Bolster is the premier slab bolster on the market with the following features: Contains sharp “needles” on bottom of foot to provide excellent stability. Gray color; blends with concrete; also available in black color. Will not rust; continuous corrosion protection, both on job-site and in concrete. Virtually no change in strength in temperatures ranging from 00F to 3000F. Easily snaps together to eliminate overlapping and use of tie-wire. Has 1/8” deep corrugation spaced 1” apart for easy rebar placement. Product Code No. Lightweight and extremely strong. Ideal for elevated slabs, precast vaults, tilt-up panels & more! 40.10.00000
30-ATLAS TECH PRODUCTS
GTI COMPOSITE BAR CHAIR & HIGH CHAIR
50-FLATWORK ACCESSORIES
40-REBAR SUPPORTS
The GTI Composite Bar Chair is the ideal reinforcement support for poured-in-place decks, post-tensioned parking decks, tilt-up panels and precast construction. This lightweight bar support offers superior strength and stability, without the worries of rust or bleed marks. Available in multiple heights, ranging from 1/2” to 10-1/4”. Contains sharp “needles” on bottom of foot to provide excellent stability. Gray color; blends with concrete. Will not rust; continuous corrosion protection, both on job-site and in concrete. Virtually no change in strength in temperatures ranging from 00F to 3000F. Lightweight and extremely strong. Product Code No. Available with sand plates for slab on grade applications. Sand plates 40.20.17000 contain protrusion in center of plate to dig into soil for added stability.
GTI COMPOSITE PC CHAIR
60-PRECAST & TILT-UP
The GTI Composite PC Chair is the ideal reinforcement for precast concrete slabs and wall panels, tilt-up concrete wall panels and elevated slabs. Available in multiple heights, ranging from 1/2” to 12” in 1/4” increments. Gray Color, blends with concrete. Ball on foot is virtually invisible on concrete surface. Designed for maximum aggregate flow and concrete consolidation. Product Code No. Will cradle all sizes of reinforcing. 40.20.19000 Larger stable footprint.
PRODUCTS
POST-TENSIONED SLAB PRODUCTS The Mono-Strand Slab-On-Ground Product System from GTI provides a full range of products for the construction of post-tensioned slabs. Post-tensioned slabs are an effective method to support light commercial and residential buildings built on expansive soils. The components of the post-tensioned slab system include ductile cast iron anchors and wedges, pocket formers and intersectional chairs.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
REBAR SUPPORT
20-FORMING ACCESSORIES
10-FORMING & SHORING
REBAR SUPPORTS
Engineered to support the post-tensioning tendons to mid-height of slab, intersectional chairs are typically installed at the intersection of tendons. Available in multiple heights, ranging from 1-1/2” to 7” high. Product Code No. 40.80.00000
130
www.atlasform.com
Serving Concrete Customers Since 1980.
REBAR SUPPORTS
20-FORMING ACCESSORIES
METAL SLAB BOLSTER
10-FORMING & SHORING
REBAR SUPPORT
Used to support lower slab steel from the slab form. Legs are spaced on 5” centers. Available in 3/4” to 3” heights in 5’ lengths and in plastic dipped, bright basic, galvanized or stainless steel protected. Product Code No. 40.15.00000
30-ATLAS TECH PRODUCTS
METAL BEAM BOLSTER Used to support lower beam steel from the soffit form. Legs are spaced on 2-1/2” centers. Available in 1-1/2” to 5” heights in 5’ lengths. Manufactured in plastic dipped, bright basic and stainless steel protected. Product Code No.
40-REBAR SUPPORTS
40.15.00000
CONTINUOUS HIGH CHAIR
50-FLATWORK ACCESSORIES
Provides support for upper slab steel eliminating the need for carrier bars. Fabricated in 2” to 15” heights in 5’ lengths with legs spaced on 8” centers. Available in plastic dipped, bright basic, galvanized and stainless steel protected. Special Order
INDIVIDUAL METAL HIGH CHAIR 60-PRECAST & TILT-UP
Used to support upper steel directly or by means of a carrier bar. Available in 2” to 15” heights in plastic dipped, bright basic, galvanized, and stainless steel protected. Product Code No. 40.25.30000
PRODUCTS
Used to support wide spaced light steel in slab construction. Available in 3/4” to 2” heights in plastic dipped, bright basic, galvanized and stainless steel protected.
70- FOUNDATION
METAL BAR CHAIR
Product Code No. 40.25.10000
80- TOOLS & PLACING
www.atlasform.com
131
10-FORMING & SHORING
REBAR SUPPORTS
Contractor Committed.
REBAR SUPPORT
20-FORMING ACCESSORIES
E-Z LOK WHEEL Side-Form spacer. Designed for medium to heavy duty projects. Multiple hub diameter for rebar sizes #3 to #6. Wider locking hub eliminates “racking” and will not fall off. Once locked onto rebar, this wheel will not change shape and will always provide uniform cover. Product Code No.
30-ATLAS TECH PRODUCTS
40.35.00000
SPACE WHEEL Side-Form spacer. Designed to fit a wide-range of bar and wire mesh sizes. Provides minimal surface contact and is lightweight. Covers from 3/8” to 3”. Meets all requirements and qualifies as a CRSI Class 1 Bar Support. Product Code No.
40-REBAR SUPPORTS
40.35.00000
E-Z CHAIR Minimal surface contact. Designed for maximum aggregate flow and concrete consolidation. Has high load capacity and fits up to #8 rebar.
50-FLATWORK ACCESSORIES
Product Code No. 40.20.00000
TOWER CHAIR
60-PRECAST & TILT-UP
Minimal surface contact. Designed for maximum aggregate flow and concrete consolidation. Has high load capacity and fits up to #8 rebar. Tower chair straddles bottom rebar mat in double mat applications. Product Code No. 40.20.60000
PRODUCTS
Supports rebar and mesh with modest surface contact. Cover height from 1/2” to 2”. Meets all requirements and qualifies as a CRSI Class 1 Bar Support. Special Order
POST-TENSION CABLE CHAIR
80- TOOLS & PLACING
70- FOUNDATION
X-CHAIR
For post-tension and on grade applications. Cover height from 1 1/2” to 3”. Four posts securely fasten at the intersection of two cables. Special Order
132
www.atlasform.com
Serving Concrete Customers Since 1980.
REBAR SUPPORTS
20-FORMING ACCESSORIES
STRONGBACK BOLSTER
10-FORMING & SHORING
REBAR SUPPORT
For precast, elevated slab, tilt wall, post tension, parking garage decks and side form spacer applications. Cover height from 3/4” to 3”. Manufactured in 32” lengths in standard boxes. Can be used individually or snapped together to create any length. Simple to install non-corrosive and lightweight. Meets all requirements and qualifies as a CRSI Class 1 Bar Support. Product Code No. 40.10.30000
30-ATLAS TECH PRODUCTS
PLAIN DOBIES
40-REBAR SUPPORTS
Plain dobies come in a number of standard heights, 3/4” to 6”, with many of the dobies offering multiple dimensions to meet various cover requirements and are used primarily for spacing the reinforcement off grade or formwork. They are particularly suited for footing and foundation reinforcement work where heavy concentrations of rebar occur. Meets all requirements and Product Code No. qualifies as a CRSI Class 1 Bar Support. 40.30.00000
WIRE DOBIES
50-FLATWORK ACCESSORIES
Wire dobies are furnished with two 16 gauge wires for attaching to rebar or mesh. Wire dobies can be used in all concrete slab applications and vertical applications as a side form spacer. Meets all requirements and qualifies as a CRSI Class 1 Bar Support. Product Code No. 40.30.00000
COMBINATION DOBIES
60-PRECAST & TILT-UP
On-Grade or Below Grade applications. Designed with multiple heights within a single unit. Standard 4000 strength. Additional strength available. Meets all requirements and qualifies as a CRSI Class 1 Bar Support.
Product Code No. 40.30.00000
DOWEL DOBIES
PRODUCTS
40.30.00000
70- FOUNDATION
On-Grade or Below Grade applications. Uniquely supports two mats of reinforcement when used with 90 degree bent rebar dowel. Dowel hole made to accept #4 rebar, depth of hole is 1/2” from bottom. Standard 4000 PSI. Additional strength available. Ideally suited for heavy rebar mats on-grade. Meets all requirements and qualifies as a CRSI Class 1 Bar Support. Product Code No.
ATLAS TIE WIRE 80- TOOLS & PLACING
Available in 16 & 16-1/2 gauge, Atlas Tie Wire may be used for multiple jobsite applications, including securing rebar in place. This professional quality soft annealed wire is packaged 20 coils per box. Plastic-coated and galvanized wire available on special order. Product Code No. 40.70.00000
www.atlasform.com
133
D-42
30-ATLAS TECH PRODUCTS
Length
Product Code No.
Wt. Lbs. per 100
4”
40.70.20400
6.1
5”
40.70.20500
6.9
6”
40.70.20600
7.8
7”
40.70.20700
8.7
8”
40.70.20800
11.3
12”
40.70.21200
13
Sold in full bags only.
D-50
DBR COUPLER Special Order
40-REBAR SUPPORTS 50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
BAG TIES
D-51 D-52 D-53 D-54
Rebar Size
Thread Dia.
Plain Product Code No.
#4
1/2”
0.2
#5
5/8”
0.3
#6
3/4”
0.4
#7
7/8”
0.5
Wt. Lbs./ Ea.
1”
0.7
#9
1-1/8”
1.1
#10
1-1/4”
1.7
#11
1-3/8”
2.2
DBR SETTING - SPLICE BARS Rebar Size
Thread Size
Color Code
Thread Data
#4
1/2”
Clear
13 NC
#5
5/8”
Red
11 NC
#6
3/4”
Orange
10 NC
#7
7/8”
Blue
9 NC
#8
1”
Green
8 NC
#9
1-1/8”
Red
7 NC
#10
1-1/4”
Orange
8 UN
#11
1-3/8”
Green
8 UN
PRODUCTS
- Custom Fabricated Product
134
Epoxy Product Code No.
#8
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
16 GA. ANNEALED
20-FORMING ACCESSORIES
10-FORMING & SHORING
REBAR SUPPORTS
www.atlasform.com
Serving Concrete Customers Since 1980.
REBAR SUPPORTS
D-101 STRAIGHT DOWEL-IN
D-102 Thread Size
#4
5/8”
#5
3/4”
#6
7/8”
#7
1”
#8
1-1/8”
#9
1-1/4”
#10
1-7/16”
#11
1-9/16”
90° HOOKED DOWEL-IN
D-103
180° HOOKED DOWEL-IN
D-104 STRAIGHT DOWEL-IN THREAD BOTH ENDS
D-101
DOWEL BAR SPLICER (DB-SAE)
STRAIGHT DOWEL BAR SPLICER
REBAR SIZES #4 THRU #11 CUSTOM FABRICATED PRODUCT Washer Dia.
#4
1-7/8” 2”
#6
2-3/8”
#7
2-1/2”
#8
2-1/2”
#9
2-3/4”
#10
3”
#11
3-1/8”
D-103
180° HOOKED DOWEL BAR SPLICER
D-104
DOUBLE ENDED DOWEL BAR SPLICER
D-108
HEADED DOWEL BAR SPLICER
50-FLATWORK ACCESSORIES
#5
D-102
90° HOOKED DOWEL BAR SPLICER
40-REBAR SUPPORTS
Rebar Size
30-ATLAS TECH PRODUCTS
D-108 HEADED DOWEL-IN
20-FORMING ACCESSORIES
Rebar Size
10-FORMING & SHORING
DOWEL-IN (D-1) REBAR SIZES #4 THRU #11 CUSTOM FABRICATED PRODUCT
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
135
D-140
Contractor Committed.
STUDRAIL® Studrail® is a cost effective solution to punching shear at column/slab connections. Studrails reduce congestion around the column connections, while at the same time dramatically reducing labor costs. Studrails are typically used in post tension and reinforced concrete slabs with direct loading on the columns. Drop panels, beams and column capitals may be eliminated to allow efficient use of flying forms. Installation of Studrails in foundations will increase the punching shear capacity at the base of the columns and in the pile caps. This can provide significant reduction in slab thickness and substantial savings in material, excavation and concrete pumping costs. Studrails can also be used in place or hairpins to eliminate congestion in post-tensioned tendon anchorage zones. One Studrail replaces a series of hairpins to provide time, labor and material savings.
40-REBAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
REBAR SUPPORTS
STUDRAIL® SPECIFICATION
50-FLATWORK ACCESSORIES
Studrail® is fabricated with special studs, either studwelded or mechanically crimped to a steel rail.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Material Specifications: • Shear Studs - Low carbon steel, C1015 in accordance with ASTM A108. • Yield Strength - 50,000 psi minimum. • Tensile Strength - 60,000 psi minimum. • Elongation in 2” - 20%
SEISMIC PERFORMANCE Studrail® has been extensively tested and proved to withstand seismic movement and maintain connection stability long after other connections systems have failed. Lab test results show that Studrails provide superior ductility and lateral drift capacity compared to other systems.
136
www.atlasform.com
Serving Concrete Customers Since 1980.
REBAR SUPPORTS
D-250
Product Code No.
Outside Dia (in.)
Length
Wt. Lbs.
Bolt Qty.
Head Size
Nominal Shear Torque
4S/CA
#4-13M
40.60.10401
1.3
3.9
1.0
2
0.5
40
5S/CA
#5-16M
40.60.10501
1.7
4.5
1.8
2
0.5
80
6S/CA
#6-19M
40.60.10601
1.9
6.3
3.5
3
0.5
80
7S/CA
#7-22M
40.60.10701
1.9
8.0
4.1
4
0.5
80
8S/CA
#8-25M
40.60.10801
2.2
10.2
7.6
4
0.625
180
9S/CA
#9-29M
40.60.10901
2.9
9.0
11.4
3
0.75
280
10S/CA
#10-32M
40.60.11001
2.9
11.5
15.5
4
0.75
350
11S/CA
#11-36M
40.60.11101
3.1
14.0
20.5
5
0.75
350
14S/CA
#14-43M
40.60.11401
3.5
16.5
26.0
6
0.75
350
18S/CA
#18-57M
40.60.11801
4.3
27.1
60.0
10
0.75
475
40-REBAR SUPPORTS
For Use On Rebar Size (in. mm)
30-ATLAS TECH PRODUCTS
Coupler Designation
20-FORMING ACCESSORIES
The D-250 Bar-Lock S/CA-Series couplers are available in rebar sizes #4 through #18 and exceed 135% of specified yield Grade 60 rebar. S/CA couplers are an approved Caltrans “Service” splice and are recognized by ICC, ACI and most State departments of Transportation. S/CA couplers are available in transition sizes, weldable half couplers and epoxy coated.
10-FORMING & SHORING
BAR-LOCK L-SERIES & S/CA SERIES COUPLERS
Meets or exceeds Min. 135% Fy, CAL TRANS Service ICBO Type 1 Available in Epoxy and Electro-Galvanized.
50-FLATWORK ACCESSORIES
Product Code No.
Outside Dia (in.)
Length
Wt. Lbs.
Bolt Qty.
Head Size
Nominal Shear Torque
4L
#4-13M
40.60.10400
1.3
5.5
1.6
3
0.5
40
5L
#5-16M
40.60.10500
1.7
6.3
2.8
3
0.5
80
6L
#6-19M
40.60.10600
1.9
8
4.5
4
0.5
80
7L
#7-22M
40.60.10700
1.9
9.8
5.5
5
0.5
80
8L
#8-25M
40.60.10800
2.2
12.3
9.5
5
0.625
180
#9-29M
40.60.10900
2.9
11.5
15.5
4
0.75
280
#10-32M
40.60.11000
2.9
14
19.5
5
0.75
410
11L
#11-36M
40.60.11100
3.1
16.5
24
6
0.75
410
14L
#14-43M
40.60.11400
3.5
19.1
32
7
0.75
410
80- TOOLS & PLACING
9L 10L
PRODUCTS
For Use On Rebar Size (in. mm)
Meets or exceeds Min. 160% Fy, CAL TRANS Service ICBO Type 1, ICBO Type 2 Available in Epoxy and Electro-Galvanized.
www.atlasform.com
70- FOUNDATION
Coupler Designation
60-PRECAST & TILT-UP
The D-250 Bar-Lock L-Series is similar to the Standard Coupler but is designed for use when higher loads are required. L-Series couplers are available in rebar sizes #4 through #14 and exceed 160% of specified yield of Grade 60 rebar. L-Series couplers are approved for use by most state DOTs, are recognized as an ICC Type 2 seismic splice, and meet ACT specifications. L-Series couplers are also available in transition sizes, weldable half couplers and epoxy coated.
137
Contractor Committed.
K-4 K-5
WELDED DOWEL ASSEMBLIES FOR PROPER LOAD TRANSFER AT EXPANSION OR CONTRACTION JOINTS MINIMUM SLAB THICKNESS IS 5”.
40-REBAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
REBAR SUPPORTS
*EP DWL = EPOXY DOWELS EP DWL/PE = EPOXY DOWELS WITH PATCHED ENDS FULL EP = COMPLETE EPOXY COATING TE = COMPLETE TECTYL-505 COATING
PRODUCT CODES BY STATE
50-FLATWORK ACCESSORIES
STATE
PAVEMENT DEPTH (IN INCHES) / PART NUMBER 6
AZ CA CO
DIAMETER OF DOWEL
LENGTH OF DOWEL
O/C
COATING
LB./FT.
AZ9
1-1/4
18
12
EP DWL/PE
7.77
CA9
CA12
1-1/4 1-1/2
18 18
12 12
FULL EP* FULL EP
7.77 10.65
CO12
3/4 1 1-1/4 1-1/2
18 18 18 18
12 12 12 12
EP DWL EP DWL EP DWL EP DWL
3.59 5.45 7.72 10.76
1 1-3/8 1-1/2
18 18 18
12 12 12
EP DWL EP DWL EP DWL/TE
5.54 9.18 10.73
8
9
10
11
12
13
14
18
CA8 CA10
CA11
CO6 CO8
CO9 CA10
60-PRECAST & TILT-UP
CO11 NV
CO14
NV11 NV13
PRODUCT CODES FOR AIRPORTS PLACE
PAVEMENT DEPTH (IN INCHES) / PART NUMBER 6
AIRPORT
8
9
10
11
12
13
15
18
AP12
PRODUCTS
AP15.1 AP15.2 AP18
DIAMETER OF DOWEL
LENGTH OF DOWEL
O/C
COATING
LB./FT.
1 1-1/4 1-1/2 1-1/2
19 20 20 20
12 15 18 18
VARY VARY VARY VARY
5.02 8.10 8.17 10.30
WIRE BASKETS (WITHOUT DOWELS) Dowel Baskets without dowels are available for contraction and expansion joints in slabs 4” to 9” thick. These are fabricated for 3/4”, 1”, or 1-1/4” diameter dowels as required.
80- TOOLS & PLACING
70- FOUNDATION
CO13
NV10
Type “D” Contraction Baskets and K-5 Type “D” Expansion Baskets are a standard 10” width.
138
www.atlasform.com
TIE BAR ASSEMBLY Tie Bar Assembly is a basket supporting and positioning rebar dowels of various sizes as specified by the owner of the paving. It is commonly used for longitudinal joints in both DOT and commercial applications. Available in plain or epoxy coated.
Serving Concrete Customers Since 1980.
REBAR SUPPORTS
Special Order
Welded Hook Type
Product Code No.
Pieces Per Box
Wt. Lbs. per 100
200
16.0
.306” x 6” long
200
20.0
100
25.0
.306” x 12” long
100
29.0
.306” x 14” long
100
33.0
.306” x 15” long
100
35.0
.306” x 18” long
100
41.0
3/8” x 15” long
100
50.0
1/2” x 18” long
100
100.0
20-FORMING ACCESSORIES
.306” x 8” long .306” x 10” long
K-6
K-7
Diameters: 1/2”, 5/8”, 3/4”, 1”, 1-1/4”, 1-1/2” 2”. Lengths: 18”, 24”. Other lengths & diameters are also available. CUSTOM FABRICATED PRODUCT
K-8
Dowel Size
Product Code No.
Packaging
3/4”
8.0
250
1”
10.0
250
K-11
DOWEL CAPS PLASTIC Special Order Product Code No.
Wt. Lbs. / Ea.
Pieces per carton
1/2” x 4”
.020
500
5/8” x 4”
.031
500
3/4” x 4”
.032
500
3/4” x 6”
.038
500
7/8” x 4”
.045
500 500 500
1-1/4” x 4”
.063
250
1-3/8” x 4”
.063
250
1-1/2” x 4”
.065
250
PRODUCTS
.058 .059
Available in full cartons only.
70- FOUNDATION
1” x 4” 1-1/8” x 4”
60-PRECAST & TILT-UP
Description Plastic
50-FLATWORK ACCESSORIES
Wt. Lbs. per 100
40-REBAR SUPPORTS
DOWEL ALIGNER Special Order
30-ATLAS TECH PRODUCTS
To order, specify: type, gauge and length.
SMOOTH DOWEL BARS PLAIN, PAINTED OR EPOXY
10-FORMING & SHORING
STAKE FOR DOWEL BASKETS
80- TOOLS & PLACING
www.atlasform.com
139
K-11
30-ATLAS TECH PRODUCTS
3/4” x 5”
1” x 5”
1-1/8” x 5”
1-1/4” x 5”
Welded Type Sizes 3/8” x 5”
1/2” x 5”
5/8” x 5”
3/4” x 5”
7/8” x 5”
1” x 5”
1-1/8” x 6”
1-1/4” x 5”
1-3/8” x 6”
1-1/2” x 6”
1-3/4” x 6”
2” x 6”
Welded style Dowel Cap Flanges must be notched back when installing caps on dowels in baskets
K-12
BASKET CLIP FOR DOWEL BASKETS Style
K-13
50-FLATWORK ACCESSORIES
40-REBAR SUPPORTS
DOWEL CAPS 5/8” x 5”
Product Code No.
Wt. Lbs.
Wrap-Around
8.7
Nail-Down
6.0
GROUT/EPOXY RETENTION RING FOR DOWELS Special Order
60-PRECAST & TILT-UP
Dowel Size
Product Code No.
Weight Lbs/Ea.
3/8” dia.
.014
5/8” dia.
.012
1” dia.
.016
1-1/4” dia.
.018
1-1/2” dia.
.024
PRODUCTS
REBAR PROTECTIVE COVERS
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
Crimp Type Sizes
20-FORMING ACCESSORIES
10-FORMING & SHORING
REBAR SUPPORTS
Product
Coverage
Wt.
Packaging
Product Code No.
PC110
Fits up to #8 bar
.55 Lbs
100 per box
40.55.11110
Product
Coverage
Wt.
Packaging
Product Code No.
PC-200
Fits #9 bar and over
.72 Lbs
50 per box
40.55.11200
Cal. OSHA Approval #C1703AG Federal OSHA Spec. #1926.701(b)
140
www.atlasform.com
Serving Concrete Customers Since 1980.
REBAR SUPPORTS
REBAR
*PRODUCED IN CO LOCATION ONLY Reinforcing Weights According to Area
@ 6” on center each way
13.86# sq.yd.
#3 #3
@ 8” on center each way
1.24# sq. ft.
11.16# sq.yd.
@ 9” on center each way
1.078# sq. ft.
9.70# sq.yd
#3
@ 12” on center one way
.399# sq. ft.
3.59# sq.yd.
#3
@ 12” on center each way
.799# sq. ft.
7.19# sq.yd.
#3
@ 14” on center each way
.706# sq. ft.
6.35# sq.yd.
#3
@ 15” on center each way
.62# sq. ft.
5.58# sq.yd.
#3
@ 16” on center each way
.625# sq. ft.
5.63# sq.yd.
#3
@ 18” on center one way
.269# sq. ft.
2.42# sq.yd.
#3
@ 18” on center each way
.539# sq. ft.
4.85# sq.yd.
#3
@ 24” on center one way
.199# sq. ft.
1.79# sq.yd.
#3
@ 24” on center each way
.399# sq. ft.
3.59# sq.yd.
#4
@ 9” on center each way
1.86# sq. ft.
16.74# sq. yd.
.714# sq. ft.
6.43# sq. yd.
#4
@ 12” on center each way
1.43# sq. ft.
12.87# sq. yd.
#4
@ 18” on center one way
.482# sq. ft.
4.34# sq. yd.
#4
@ 18” on center each way
.964# sq. ft.
8.68# sq. yd.
#4
@ 24” on center one way
.375# sq. ft.
3.38# sq. yd.
#4
@ 24” on center each way
.75# sq. ft.
6.75# sq. yd.
#5
@ 5” on center each way
5.37# sq. ft.
48.33# sq. yd.
#5
@ 8” on center each way
3.25# sq. ft.
29.25# sq. yd.
#5
@ 9” on center each way
2.891# sq. ft.
26.019# sq. yd.
#5
@ 12” on center each way
2.217# sq. ft.
19.953# sq. yd.
#5
@ 15” on center each way
1.834# sq. ft.
16.506# sq. yd.
#5
@ 18” on center each way
1.45# sq. ft.
13.05# sq. yd.
Area* Sq. Inches
Weight Pounds per ft.
Diameter* Inches
#3
.11
.376
3/8”
#4
.20
.668
1/2”
#5
.31
1.043
5/8”
#6
.44
1.502
3/4”
#7
.60
2.044
7/8”
#8
.79
2.670
1”
* Nominal Dimensions
50-FLATWORK ACCESSORIES
@ 12” on center one way
ASTM Standard Reinforcing Bars Bar Size Designation
40-REBAR SUPPORTS
#4
Bars are of two minimum yield levels: 1. 40,000 psi, Grade 40, ASTM A 615. 2. 60,000 psi, Grade 60, ASTM A 706.
30-ATLAS TECH PRODUCTS
1.544# sq. ft.
20-FORMING ACCESSORIES
#3
10-FORMING & SHORING
REBAR FABRICATION
60-PRECAST & TILT-UP PRODUCTS
Denver, CO
80- TOOLS & PLACING
*AVAILABLE IN CO LOCATION ONLY
www.atlasform.com
70- FOUNDATION
FABRICATED REBAR
141
Contractor Committed.
WELDED WIRE FABRIC ASTM uses the letter “W” to designate smooth wire and the letter “D” to describe deformed wire. there are three widely used styles of fabric namely 4, 6 and 10 gauge. The corresponding Wnumbers for smooth fabric are:
20-FORMING ACCESSORIES
10-FORMING & SHORING
REBAR SUPPORTS
30-ATLAS TECH PRODUCTS
4 gauge equals W4.0 6 gauge equals W2.9 10 gauge equals W1.4
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-REBAR SUPPORTS
Welded wire fabric is designated by two number and two letter-number combinations. The first number gives the spacing in inches of the longitudinal wires. The second number gives the spacing of the transverse wires in inches. The first letter-number combination gives the type and the size of the longitudinal wire and the second combination gives the information on the transverse wire.
Common Stock Styles New Designation (by W-number)
Old Designation (by steel wire gauge)
Product Code No.
Weight Approx. per 100 S. F.
6 x 6 - W2.9 x W2.9
6x6x6x6
40.53.24606
-
6 x 6 -W1.4 x W1.4
6 x 6 x 10 x 10
40.53.24610
-
4 x 4 -W4.0 x W4.0
4x4x4x4
40.53.10404
85
4 x 4-W2.9 x W2.9
4x4x6x6
40.53.10406
62
6 x 6 - W4.0 x W4.0
6x6x4x4
40.53.20604
58
6 x 6 - W2.9 x W2.9
6x6x6x6
40.53.20606
42
6 x 6 - W2.0 x W2.0
6x6x8x8
40.53.20608
29
6 x 6 -W1.4 x W1.4
6 x 6 x 10 x 10
40.53.20610
21
6 x 6 x 10 x 10
40.53.30610
-
SHEETS 7’ X 20’
SHEETS 8’ X 20’
ROLLS 5’ X 150’ 6 x 6-W1.4 x W1.4
142
www.atlasform.com
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
·1¼” x 3½” ·1¼” x 5½” ·1¼” x 7¼” ·1¼” x 9½” ·1¼” x 117/8” ·1¼” x 14” ·1¼” x 16”
30-ATLAS TECH PRODUCTS
The LVL EDGE will also resist deforming, bowing, warping and swelling and is dimension stable as compared to other form boards. Easy to nail and is virtually knot free, the LVL EDGE, produces clean and consistent concrete finishes time and time again.
Available in these standard sizes:
20-FORMING ACCESSORIES
The Atlas LVL EDGE is a revolutionary concrete edge form designed for flatwork, tilt-up, residential and commercial use. The double laminated finger joint panels provide the support and high strength design. The LVL EDGE gives you higher labor efficiency and lower actual and per pour costs.
Product Code No. 50.10.00000
THE ADJUSTABLE KICKER The adjustable kicker eliminates the waste and inefficiency of traditional wood bracing.
Product Code No. 50.15.00108
16” Adjustable Kicker
50.15.00116
CURB FORMS
PRODUCTS
The Street Smart Forming System is ideal for applications that include sideways, driveways, curb and gutters, pavements, footings and industrial slabs.
www.atlasform.com
80- TOOLS & PLACING
Standard forms available in 10’ lengths, with heights ranging from 4” to 24”.
70- FOUNDATION
STREET SMART
60-PRECAST & TILT-UP
Description
50-FLATWORK ACCESSORIES
• Works on any surface including earth, wood, concrete and blacktop. • Adjusts to various slopes and angles. • Attaches easily to either steel or wood forms and makes straighter edges with less work. • Can be reused and moved from pour to pour.
40-BAR SUPPORTS
EDGE FORM BRACING
8” Adjustable Kicker
10-FORMING & SHORING
ATLAS LVL EDGE CONCRETE EDGE FORM
LVL EDGE FORM
143
1/2” x 1” FLAT
30-ATLAS TECH PRODUCTS
Length
Product Code No.
Wt. Lbs.
Length
12”
50.15.50012
1.74
12”
Product Code No.
Wt. Lbs.
18”
50.15.50018
2.70
18”
50.15.60018
2.70
24”
50.15.50024
30”
50.15.50030
3.65
24”
50.15.60024
3.65
4.61
30”
50.15.60030
36”
50.15.50036
4.61
5.56
36”
50.15.60036
5.56 6.51
42”
50.15.50042
6.51
48”
50.15.50048
7.47
48”
7.47
9.33
60”
9.33
60”
3/4” ROUND
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
11/16” SQUARE Length
Product Code No. With Hole
Product Code No. Without Holes
Wt. Lbs.
1.24
12”
50.15.23012
50.15.22012
1.24
50.15.40018
1.92
18”
50.15.23018
50.15.22018
1.92
50.15.40024
2.61
24”
50.15.23024
50.15.22024
2.61
50.15.40030
3.29
30”
50.15.23030
50.15.22030
3.29
50.15.23036
50.15.22036
3.97
Length
Product Code No.
Wt. Lbs.
12”
50.15.40012
18” 24” 30” 36”
50.15.40036
3.97
36”
42”
50.15.40042
4.65
42”
50.15.23042
50.15.22042
4.65
48”
50.15.40048
5.33
48”
50.15.23048
50.15.22048
5.33
6.67
60”
60”
1/2” x 1” FLAT
144
1.74
42”
3/8” X 1-1/2” FLAT
11/16” SQUARE
PRODUCTS
60-PRECAST & TILT-UP
3/8” X 1-1/2” FLAT
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
STEEL STAKES
20-FORMING ACCESSORIES
10-FORMING & SHORING
FLATWORK ACCESSORIES
www.atlasform.com
6.67
3/4” ROUND
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
EXPANSION JOINT FILLERS
50.50.00000
ASPHALT EXPANSION JOINTS
20-FORMING ACCESSORIES
A waterproof expansion joint that is the basic joint for almost every type of installation...offers low initial cost, great durability, and is self-sealing. Available in thicknesses of 1/4”, 3/8”, 1/2”, 3/4”, and 1”. Slabs available in 36” and 48” widths and standard lengths of 5’, 6’, and 10’. Pre-cut joints available in any desired uniform widths and standard lengths. Curb and gutter sections and other special shapes and punching for dowels available. Approx. weight: 3 lbs. per square foot based on 1/2” thickness. Meets ASTM D-994 and AASHTO M 33.
10-FORMING & SHORING
Expansion Joint Product Code No.
FIBER EXPANSION JOINTS 30-ATLAS TECH PRODUCTS
Suggested for use on highways, airport runways, and other similar installations where the joint can be sealed with a rubber asphalt joint seal. Available in thicknesses of 1/4”, 3/8”, 1/2”, 3/4”, and 1” . Slabs available in 5’, 10’, 11’, 12’, and 12’6” lengths. Pre-cut in uniform widths and lengths as desired. Special shapes and punching are available. Approximate weight is 1.4 lbs. per square foot based on 1/2” thickness. Meets ASTM D-1751; Federal HH-F-341c, Type 1 and AASHTO M 153-54, Type 3.
40-BAR SUPPORTS
CERAMAR EXPANSION JOINTS Composed of a unique blend of isomeric polymers in a very small, closed-cell structure. Gray in color, Ceramar is a lightweight, highly flexible and resilient material offering recovery qualities of over 99%. This mini closed-cell structure is virtually non-absorbent. It can be wrapped or formed around curved or circular surfaces. Available in thicknesses of 1/4”, 3/8”, 1/2”, 3/4”, and 1”. Slabs available in 48” widths and standard lengths of 10’. Meets ASTM D-1752.
50-FLATWORK ACCESSORIES
GRAY SPONGE RUBBER EXPANSION JOINTS Ideal for use where joint is visually exposed and complete resiliency is essential...fully compressible with recovery rate of 95% or more of original thickness. Sizes: thicknesses of 1/4”, 3/8”,1/2” 5/8”, 3/4”, and 1”, widths 2” to 48”, and lengths of 5’ and 10’. Approximate weight is 1.85 lbs. per square foot based on 1/2” thickness. Meets ASTM D-1752, Type 1 Federal HH F 341c, Type 2, Class A, and AASHTO M 153-54, Type 1.
60-PRECAST & TILT-UP
CORK EXPANSION JOINTS
PRODUCTS
SELF-EXPANDING CORK EXPANSION JOINTS
www.atlasform.com
80- TOOLS & PLACING
Formed and compressed under heat and pressure to permit expansion up to 140% of original thickness after installation which permits the filler to compensate for concrete shrinkage. Normal humidity conditions after installation activate the self-expanding properties of the cork. Sizes: thicknesses, 1/2”, 3/4”, and 1”. Meets ASTM D-1752, Type 3; Federal HH-F-341c, Type 2, Class C; AASHTO M-153-54, Type 3.
70- FOUNDATION
Molded of selected cork granules with a resin binder. Use where it is essential that joints are kept filled at all times, such as in sewage plants, flood walls, filtration plants, etc. Resilient, will compress without extrusion and recover to 95% of original thickness. Sizes: thickness, 1/4”, 3/8”, 1/2”, 3/4”, and 1”; widths 2” to 36”; and lengths of 5’ and 10’. Meets ASTM D-1752, Type 2; Federal HH-F-341c, Type 2, Class B.
145
FLATWORK ACCESSORIES
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
REMOVABLE CAP STRIPS
50.55.10050 50.55.10020
50.55.10040
50.55.10030
PLASTIC ZIP STRIP JOINT FORMER Length
G-28
Product Code No.
1”
50.55.30100
1-1/2”
50.55.30150
2”
50.55.30200
SCREED BRACKET FOR 3/4” DIA. ROUND STAKES Screed Size
Product Code No.
Wt. Lbs. per 100
Packaging
2 x 4 Lumber
50.15.10001
66.6
100 per carton
54.1
100 per carton
1/2 x 2 Iron Bar
G-29
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
Contractor Committed.
SCREED BRACKET FOR 3/4”DIA. SQUARE STAKES Screed Size
Product Code No.
Wt. Lbs. per 100
Packaging
2 x 4 Lumber
50.15.10001
63.9
100 per carton
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
HEADER FORM SUPPORT Product Code No.
Wt. Lbs.
50.15.01010
1.0 Each
Used for supporting headers on 3/4” round screed post. Nail support bracket to header. Set screw firmly clamps against screed post.
Screed Pad
Product Code No. 50.16.20000
146
SCREED PADS AND POSTS
1/2” tapped post fits threaded sections of screed pad. 1/4” and 3/8” screed posts also available. Sizes include 9”, 12”, 15”, 18”, 21” & 24”.
Tapped Screed Post
Product Code No.
9”
50.15.21009
12”
50.15.21012
15”
50.15.21015
18”
50.15.21018
24”
50.15.21024
36”
50.15.21036
For wood forms or decking. 3/4” round stock.
www.atlasform.com
Screw Point Screed Post
Product Code No.
9”
50.15.20009
12”
50.15.20012
15”
50.15.20015
18”
50.15.20018
21”
50.15.20021
24”
50.15.20024
30”
50.15.20030
36”
5015.20036
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
G-33
Actual Height
Product Code No.
Wt. Lbs. per 100 LF
4”
3-1/2”
50.16.10004
37.0
5”
4-1/2”
50.16.10005
45.0
6”
5-1/2”
50.16.1006
54.0
20-FORMING ACCESSORIES
Slab Thickness
Standard Packaging 3-1/2” Screed Key 40 bundles of 100 ft. per skid of 4,000 ft. 4-1/2” Screed Key 40 bundles of 100 ft. per skid of 4,000 ft. 5-1/2” Screed Key 30 bundles of 100 ft. per skid of 3,000 ft. Available only in full packages of 100 ft.
G-34
STAKES NOT INCLUDED (SEE G-37) Slab Thickness
Actual Height
Product Code No.
Wt. Lbs. per 100 LF
8”
7-1/2”
50.16.10108
71.0
10” to 12”
9-1/2”
50.16.10110
86.0
Product Code No.
Wt. Lbs. Per LF
50.16.15110
.060
G-35
Product Code No.
Wt. Lbs. per 100
12”
50.16.11012
22.0
15”
50.16.11015
27.0
18”
50.16.11018
33.0
24”
50.16.11024
43.0
PRODUCTS
Standard Packaging 12” Stakes 60 cartons of 100 per skid of 6,000 pieces. 15” Stakes 60 cartons of 100 per skid of 6,000 pieces. 18” Stakes 48 cartons of 100 per skid of 4,800 pieces. 24” Stakes 40 cartons of 100 per skid of 4,000 pieces.
70- FOUNDATION
Length
60-PRECAST & TILT-UP
STAKE FOR SCREED KEY AND LOAD KEY G-37
50-FLATWORK ACCESSORIES
REMOVABLE PLASTIC CAP STRIP
40-BAR SUPPORTS
Standard Packaging 7-1/2” Load Key 20 bundles of 100 ft. per skid of 2,000 ft. 9-1/2” Load Key 20 bundles of 100 ft. per skid of 2,000 ft. Available only in full packages of 100 ft.
30-ATLAS TECH PRODUCTS
LOAD KEY
10-FORMING & SHORING
SCREED KEY STAKES NOT INCLUDED (SEE G-37) 24 GA. MATERIAL
80- TOOLS & PLACING
www.atlasform.com
147
E-1
Contractor Committed.
RISER FRAMES, STANDARD Special Order
E-2
Size
Wt. Lbs.
“H” height 15” max
93.0
RISER FRAMES FOR SLAB ON FILL Special Order Size “H” height 15” max
E-3
RISER FRAMES SLOPING SLAB Special Order
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FLATWORK ACCESSORIES
Size “H” height 15” max
E-7
CUT WASHER Bolt Dia.
Dimension
Plain Product Code No.
1/2”
1-3/8” x 3/32”
20.30.80704
4.4
3/4”
2” x 5/32”
20.30.80504
10.3
1”
2-1/2” x 3/32”
20.30.80304
16.7
1-1/4”
3” x 3/32”
20.30.80204
21
1-1/2”
PRODUCTS
D-15
Galvanized Product Code No.
20.30.80104
PAPER TUBING Nominal Tube Dia.
Product Code No.
Wt. Lbs. per 100
Approx. Ft. per Box
3/8”
40.45.28012
2.6
500
1/2”
40.45.27012
4.7
400
5/8”
40.45.26012
5.7
300
3/4”
40.45.25012
6.4
200
1”
40.45.23012
7.5
100
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
“W” width 18” max
148
www.atlasform.com
Wt. Lbs. per 100
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
4’ x 8’ Sheets Product Code No.
1/2”
50.30.10050
3/4”
50.30.10075
1”
50.30.10100
1-1/2”
50.30.10150
2”
50.30.10200
2-1/2”
50.30.10250 50.30.10300 50.30.10350
4”
50.30.10400
5”
50.30.10500
6”
50.30.10600
30-ATLAS TECH PRODUCTS
3” 3-1/2”
20-FORMING ACCESSORIES
Thickness
40-BAR SUPPORTS
PHYSICAL PROPERTIES OF EXPANDED POLYSTYRENE Properties
Units
ASTM test
Density (pcf) 1.0
at 40F at 75F
Thermal Conductivity
at 40F at 75F
1.5
2.0
4.1 3.8 C 177
0.24 0.26
0.22 0.24
0.21 0.23
in/(in) (F)
D 696
0.000035
0.000035
0.000035
F F
-
up to 167 max 180
up to 167 max 180
up to 167 max 180
Compression strength 10% deflection
p si
D 1621
13-17
21-27
30-38
Flexural strength
p si
C 203
28-35
40-60
60-90
-
-
none
none
none
Coefficient of thermal expansion Effective temperature-continuous range intermittant
Capillarity Water vapor transmission
60-PRECAST & TILT-UP
BTU/(hr) (sq ft) (F/in)
50-FLATWORK ACCESSORIES
R Value
1.2-3.0
0.8-1.7
0.6-1.2
%
C 272
less than 2
less than 1.5
less than 1.0
Bond strength-Portland cement (in shear) gypsum plaster
p sf p sf
-
830 530
830 530
830 530
PRODUCTS
C 355
FIRE HAZARD CLASSIFICATION
www.atlasform.com
1" Thickness 5 0 50-85
80- TOOLS & PLACING
4" Thickness 5 0 250-350
70- FOUNDATION
perm in
Water absorption (by volume)
Flame Spread Fuel Contributed Smoke Developed
10-FORMING & SHORING
EXPANDED POLYSTYRENE
149
10-FORMING & SHORING
FLATWORK ACCESSORIES
Contractor Committed.
TRENCH DRAIN SYSTEMS 300 SERIES GRATE
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
Non-Metal Grates Proof Load PSI
Material
Length (in.)
Wt. Lbs.
Locking Device
2336
15
Termoplastic Heel-proof
19.60
1.1
2840.25A
400 SERIES GRATE Perforated Heel-Proof Grates Product Code No.
Proof Load PSI
2410 2452 2486
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
Length (in.)
Wt. Lbs.
Locking Device
Product Code No.
Proof Load PSI
15
Galvanized Steel
39.19
6.0
2810A
2420
15
18-8 Stainless Steel
39.19
6.0
2840A
2440
15
Brass
39.19
8.0
2892A
Reinforced Perforated Heel-Proof Grates Load Class
Material
Length (in.)
Wt. Lbs.
Locking Device
2412
A-B
Galvanized Steel
39.19
8
2810A
2454
A-B
18-8 Stainless Steel
39.19
8
2840A
Material
Length (in.)
Wt. Lbs.
Locking Device
150
Galvanized Steel
39.19
6.0
2811A
150
18-8 Stainless Steel
39.19
6.0
2841A
Product Code No.
Proof Load PSI
Material
Length (in.)
Wt. Lbs.
2422 2442 2442.19
Locking Device
300
Galvanized Steel
39.19
8.0
2811A
300
18-8 Stainless Steel
39.19
8.0
2841A
300
18-8 Stainless Steel
39.19
8.0
2841A
Load Class A-B-C perforated grating availabel on special order basis. Special Accessories
422
420
410
Product Code No.
Material
Length (in.)
Wt. Lbs.
2498.04SS 2459
Stainless Steel Heavy Duty Frame
39.19
19.0
Stainless Steel Overlay Rails
39.19
1.5
500 SERIES GRATE Ductile Iron Solid Cover
Slotted Grates
Product Code No.
Proof Load PSI
Material
Length (in.)
Wt. Lbs.
Locking Device
Product Code No.
Proof Load PSI
Material
Length (in.)
Wt. Lbs.
Locking Device
2501
300
Ductile Iron
19.6
12
2811B
2502
300
Ductile Iron
19.6
8
2811B
2503
600
Ductile Iron
19.6
11
2811B
*501 cover is also compatible with the 510 frame
Ornamental Ductile Iron Gate
Longitudinally Slotted Grates Product Code No.
Proof Load PSI
Material
Length (in.)
Wt. Lbs.
Locking Device
2504
600
Ductile Iron
19.6
10.0
2811B
Product Code No.
Proof Load PSI
Material
Length (in.)
Wt. Lbs.
Locking Device
2505
300
Ductile Iron
19.6
10
2811B
2506
300
Ductile Iron
19.6
7
2811B
530 Frame & Grate Assemblies Product Code No.
Proof Load PSI
Material
Length (in.)
Wt. Lbs.
Locking Device
2532
600
Gray iron (class 30) and 502 style
19.6
30
2815F
2534
600
Gray iron (class 30) frame and ductile iron longitudinally-slotted grate
19.6
25
2815F
80- TOOLS & PLACING
PRODUCTS
Slotted Steel Grates
Material
Reinforced Slotted Steel Grates
Product Code No.
70- FOUNDATION
313
Product Code No.
502
150
510 MFFAF Fabrication/End Frame Product Code No.
Load Class
Material
Length (in.)
Wt. Lbs.
Locking Device
2510MFFAF
N/A
Ductile Iron
19.6
9.0
N/A
Note: One is required at each end run, one at each tee, two are required at 90° turn.
504
www.atlasform.com
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
510AF Frame & Grate Assemblies
Ornamental ADA Heel-Proof Grate/Frame
2564
Proof Load PSI 600
Material Ductile Iron
Length (in.) 19.6
Wt. Lbs.
Locking Device
12
N/A
All ductile iron grates and frames available with galvanized coating. All ductile and cast grates have compatible anchor frames.
Load Class
Material
Length (in.)
Wt. Lbs.
Locking Device
2511AF
300
Ductile iron frame and 501
19.6
21.0
2815B
2512AF
300
Ductile iron frame and 502
19.6
15.0
2815B
2513AF
600
Ductile iron frame and 503
19.6
18.0
2815B
2514AF
600
Ductile iron frame and 504
19.6
17.0
2815C
2515AF
300
Ductile iron frame and 505
19.6
17.0
2815B
2516AF
300
Ductile iron frame and 506
19.6
11
2810AXL
20-FORMING ACCESSORIES
Product Code No.
Product Code No.
10-FORMING & SHORING
TRENCH DRAIN SYSTEMS
532 505
510MFF
30-ATLAS TECH PRODUCTS
512AF
700 SERIES GRATE 720
Proof Load PSI
Material
Length (in.)
Wt. Lbs.
Locking Device
2720
150
Vinyl ester (bars on 1” centers)
39.19
4.0
2887
2722
300
Vinyl ester (bars on 0.6” centers)
39.19
6.0
2887
722
50-FLATWORK ACCESSORIES
Product Code No.
40-BAR SUPPORTS
Vinyl Ester FRP Slotted Grates
60-PRECAST & TILT-UP
Cross-Sectional View Channel With In-Lay Type Grate
Cross-Sectional View Channel Frame And Grate
PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
151
Contractor Committed.
TRENCH DRAIN SYSTEMS
All runs should terminate with nos. 050, 100, 150, 200, 250, 300 or any non-sloping channel (nos. 021, 091, or 291) at outlet or deep end. Any channel may serve as shallow end.
Non-sloping channel locations - All have 100 mm (4”) and 150 mm (6”) vertical outlet.
The PolyDrain Trench Drain System consists of 30 interlocking channels, each one meter (39.19”) long. Special non-sloping channels can be inserted at specified intervals in order to extend channel runs. Catch basins, horizontal outlet plates, closed end plates and vertical outlet plate adapters can be installed at designated locations. Closed end plates terminate channel runs. NOTE: Always begin at the appropriate outlet channel, working towards the shallow end.
PRODUCTS
Trench Drain Product Code No.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FLATWORK ACCESSORIES
50.40.00000
152
www.atlasform.com
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
There are two vapor retarder specifications with very different performance requirements:
PERMINATOR™ 10 mil - 3,000 sq. ft. rolls; 15’ x 200’ PERMINATOR™ 15 mil - 2,400 sq. ft. rolls; 12’ x 200’
Moistop® Underslab With a water vapor permeance of less than .30 perms, Moistop® Underslab exceeds ASTM E-1745 requirements for water vapor permeance, providing an extremely effective barrier to moisture vapor transmission through concrete slabs. Packaging: 2,000 sq. ft. rolls (96” x 250’); 4.2 lbs. per 100 sq. ft. Thickness is 12 mils.
153
80- TOOLS & PLACING
www.atlasform.com
PRODUCTS
50.60.00000
The Boot™ The Boot is engineered to help in the installation of underslab vapor retarders around pipes. It makes installations easier while maintaining the integrity of the vapor retarding layer and jobsite durability. Its unique design makes sealing around pipes, conduits and other penetrations of any size quick and easy.
70- FOUNDATION
Vapor Retarders Product Code No.
Moistop® Tape Moistop Tape’s excellent adhesive properties help assure tight joints and smooth underslab installations while maintaining the vapor retarding characteristics required by ASTM E-1745 specifications. Available in 4 inch wide x 108 foot rolls.
60-PRECAST & TILT-UP
PREMOULDED MEMBRANE® VAPOR SEAL with Plasmatic® Core. - Underslab Vapor Barrier - 0.0011 perm rating Seven-ply, weather coated, permanently bonded, semi-flexible bituminous core board. Provides a positive, easy to install, economical, true vaporproofing and waterproofing system for horizontal applications. The product is the ultimate when a true vapor seal is required. Helps meet and maintain the maximum slab moisture transfer rate of 3 lbs./1,000 sq. ft./24 hours, allowed by the flooring industry specifications.
Packaging: Ultra 15 - 1,440 sq. ft. rolls (144” x 120’); 7.3 lbs. per 100 sq. ft. Thickness is 15 mils. Ultra 10 - 3,000 sq. ft. rolls (15’ x 200’); 4.8 lbs. per 100 sq. ft. Thickness is 10 mils. Ultra 6 - 3,000 sq. ft. rolls (240” x 150’); 2.8 lbs. per 100 sq. ft. Thickness is 6 mils.
50-FLATWORK ACCESSORIES
2) ASTM E-1993, the more stringent (lower perm rating) specification for critical area use:
40-BAR SUPPORTS
Moistop Ultra® The Moistop Ultra family represents a new generation of concrete underslab products designed to provide incredible durability on the jobsite and lasting protection against moisture. With a water vapor permeance of .02 perms and a tensile strength and puncture resistance that outperforms even thicker membranes, Moistop Ultra 15, Ultra 10 and Ultra 6 exceed all ASTM E-1745 standards for Class “A”, “B” and “C” underslab vapor retarders.
30-ATLAS TECH PRODUCTS
1) ASTM E-1745 Class A, B, and C for underslab plastic film vapor retarders:
Fortifiber Vapor Retarders
20-FORMING ACCESSORIES
W.R. Meadows Vapor Retarders
10-FORMING & SHORING
VAPOR RETARDERS
PRODUCTS
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FLATWORK ACCESSORIES
Contractor Committed.
Product Description
MOISTURE RETAINING COVERS UltraCure NCF
TM
/ Ultracure SUN
TM
UltraCure NCFTM and Ultracure SUNTM are moistureretaining coverings that are natural colored cellulose fabrics with a 3 mil clear (NCF) or reflective (SUN) impervious coating applied to one side. Ultracure SUNTM has a non-perforated reflective vapor barrier coating designed to help provide protection against UV degradation. Both non-staining fabrics have a tensile strength meeting ASTM D-882 and a mimimum retention capacity of 6.5(g). Material shall meet or exceed ASTM C171-03, ASTM C171-97a and AASHTO M171-00, standard specifications for sheet material for curing concrete slabs or pavement.
Product Code No.
Packaging
UltraCure NCF
50.65.31200
8’ x 200’ roll
UltraCure SUN
50.65.33200
8’ x 200’ roll
Property
Value
Basis Wt.
151 g/sm
ASTM D-2103
Caliper
1.4 mm
ASTM D-5199
4783 psi 4900 psi
ASTM D-882
Elongation TD MD
721% 622%
ASTM D-882
Elmendorf
1500 g 350 g
ASTM D-1992
Dart
300 g
ASTM D-1709
Reflectance
96%
ASTM E-1447
Tensile
UltraCureDOTTM UltraCureDOTTM features super absorbant fibers that effectively trap water and serve as a hydrating reservoir for the slab as it cures. UltraCureDOTTM also features a perforated white reflective poly backing which provides constant visual reinforcement that the slab remains wet for the entire curing period. With proper installation, UltraCureDOTTM provides constant hydration and maintains a 100% relative humidity condition on the slab for the entire 14 day curing period.
TD MD
• • • • • •
TD MD
ASTM Test Method
Superior Hydration Increased cured concrete strength User Friendly Cost Effective Green- LEED’s points & recyclable Greater blanket wind resistance Product Description
Product Code No.
Packaging
UltraCure DOT
50.65.30100
8’ x 100’ roll
McTech EZ Cover EZcoverTM is a natural colored cellulose fabric designed to help protect slab-on-grade or other Product Code No. flooring during the construction process. The 50.66.30050 product is available in standard width 8’ rolls weighing approximately 100 lbs each with each roll covering approximately 400 square feet on application. Property Value ASTM Test Method Basis Wt.
1200 g/sm
ASTM D-2103
Caliper
3.18mm
ASTM D-5199
Tensile
TD-8100psi MD-8800psi
ASTM D-882
Dart
2300g
ASTM D-1709
Reflectance
81%
ASTM E-1447
TRM Weather-All Polyethylene
Synthetic Burlene
White polyethylene film available in 4 mil thickness. Polyethylene ASTM C-171 for curing concrete Film Product
Combination of synthetic burlap alternative and reinforced polyethylene cover. ASTM C-171 for curing concrete
80- TOOLS & PLACING
Code No.
Clear polyethylene film available from 50.62.00000 1 mil to 20 mil thickness. ASTM E-96 for water vapor permeance ASTM C-156 for moisture retention ASTM E-154 for use as vapor retarders
154
Poly Burlap Combination of 10 oz. burlap and 5 mil white opaque polyethylene. ASTM C-171 for curing concrete
www.atlasform.com
Curing Blankets & Burlap Product Code No. 50.65.00000
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
20-FORMING ACCESSORIES
The EZform™ Dowel System was designed to save concrete contractors time and money while simplifying the process of creating large slabs-on-grade, and other concrete floors where joint forming and load transfer is critical. The system consists of patent pending elements including: the reusable EZform™ board, the EZdowel™ load transfer plate dowel, EZedge™, and the EZbasket™. The EZform System saves owners and contractors money by eliminating many costly on-site labor tasks associated with large SOG projects.
30-ATLAS TECH PRODUCTS
Eliminated tasks: • On-site sawing to create chamfer • Measuring for dowel holder alignment • Nailing dowel holders • Repairing crushed or paste filled dowel holders Product Code No.
EZ Form 4” x 16’
50.11.16040
EZ Form 51/2” x 16’
50.11.16055
EZ Form 6” x 16’
50.11.16060
EZ Dowel 1/4”
40.45.41400
40-BAR SUPPORTS
Product Description
SPEED DOWEL is a slip dowel installation system that:
60-PRECAST & TILT-UP
• Minimizes differential settlement at construction joints. • Allows unobstructed contraction and expansion of concrete slabs. • Helps reduce cracking and spalling at construction joints. • Reduces time required for form board removal between slabs. Speed Dowel
Emery Non-Slip
80- TOOLS & PLACING
Emery Non-Slip is a hard, non-slip aggregate comprised of 100% pure emery. Emery is a natural occurring mined material that is extremely hard, tough and abrasion resistant. Emery Non-Slip is completely non-corrosive and rust free, for inside and outside use.
PRODUCTS
NON-SLIP FINISH
70- FOUNDATION
Product Code No.
www.atlasform.com
50-FLATWORK ACCESSORIES
SPEED DOWEL
40.45.30000
10-FORMING & SHORING
E-Z FORM DOWEL
155
Contractor Committed.
WATERSTOPS Ribbed with Center Bulb Ribbed with center bulb waterstops are employed in expansion joints where movement between members is anticipated. They are generally used above grade but in fact are a universal design and can be used in any type of joint above or below grade.
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FLATWORK ACCESSORIES
Flat Ribbed
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
Flat ribbed waterstops are employed in construction joints where movement between members is not anticipated. They are generally used below grade in footings, walls, slabs, or for breaks in concrete due to limitations in working methods.
156
www.atlasform.com
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
Split Ribbed
Dumbbell waterstops are used in construction joints where movement between members is not anticipated. They are usually employed below grade and in horizontal applications. Dumbell waterstops with a centerbulb are suitable for use where movement between members is anticipated.
Split ribbed waterstops are used in either construction or expansion joints where the elimination of split form work is feasible. The split leg of the waterstop is spread open and nailed to the bulk head. When the form work is removed following completion of first pour, the split leg is joined together and the second pour completed.
20-FORMING ACCESSORIES
Dumbbell
10-FORMING & SHORING
WATERSTOPS
30-ATLAS TECH PRODUCTS 40-BAR SUPPORTS 50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
Waterstop Vinylex R6-316 Waterstop Vinylex R6-38
50.72.11121
Waterstop Vinylex R6-38T
50.72.12110
Waterstop Vinylex RB6-316
50.72.12130
Waterstop Vinylex RB6-38
50.72.12210
Waterstop Vinylex RB9-316
www.atlasform.com
80- TOOLS & PLACING
50.72.11120
PRODUCTS
Description
50.72.11110
70- FOUNDATION
Product Code No.
157
HENRY HYDRO-FLEX WATERSTOP
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
The Hydro-Flex waterstop is a preformed adhesive hydrophilic waterstop designed to swell in the presence of water providing a watertight seal in cold joints on concrete structures. This highly advanced product is made from butyl rubber, polypropylene elastomers, hydrophilic fillers and plasticizers providing a more uniform and controlled volumetric expansion upon contact with water. Hydro-Flex Waterstop is self-adhesive and bonds to a wide variety of substrates. Its ability to swell, allows it to penetrate into poorly consolidated concrete surfaces. Product Code No.
50-FLATWORK ACCESSORIES
50.73.11000
HENRY SYNKO-FLEX WATERSTOP
PRODUCTS
60-PRECAST & TILT-UP
Synko-Flex preformed plastic adhesive waterstop is a specially formulated non-swelling preformed joint sealant that provides a long lasting, watertight bond to both fresh and cured concrete surfaces. SynkoFlex is a single-component, self-sealing adhesive compound, extruded in a square cross-section between two quick-release protective wrappers. It bonds to cured concrete surfaces and fuses with fresh concrete during the hydration and curing process to achieve a watertight seal within cold joints at footings, walls and slabs on a wide variety of concrete structures. It does not rely on swelling to achieve its watertight seal and therefore, it is unaffected by rain or wet conditions which may occur prior to joint completion.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
WATERSTOPS
20-FORMING ACCESSORIES
10-FORMING & SHORING
FLATWORK ACCESSORIES
Product Code No.
158
Synko Flex
50.73.12000
Synko Flex Primer
50.73.12100
www.atlasform.com
Serving Concrete Customers Since 1980.
FLATWORK ACCESSORIES
ARCIS ADA TACTILE PANELS
20-FORMING ACCESSORIES
Arcis ADA panels perform the vital safety function of highlighting danger areas of complicated intersections, transit platforms, crossings and blended transitions. Premium cast stone mix combines high strength and abrasion resistance with entrained air for freeze/thaw resistance. The mixes utilize quartz and granite having extremely low absorption characteristics (less than 1% by weight) and extremely high strength and abrasion resistance. Arcis panels are cast on drop tables which can compact very dry concrete, allowing the use of a low water cement ratio (less than .3), a key to high performance concrete. Along with several special additives and a controlled heat curing process the result is a premium high-tech cast stone.
30-ATLAS TECH PRODUCTS
Features
40-BAR SUPPORTS
• Fast & easy installation. Only an additional 10 minutes to typical concrete ramp placement. • Pre-stressed with high tensile strength stainless steel tendons for impact and crack resistance. • Truncated domes meet federal regulations. • Thermal coefficient of expansion similar to concrete for maximum service life through temperature cycles. Helps prevent warping, floating, voids and tripping hazards. • Excellent durability in extreme temperatures, direct sunlight, & freeze/ thaw exposure. • No waiting for concrete to setup; begin to install as soon as ramp is poured. • No extra weights or expensive adhesives needed to keep panels down. • Can cut to fit custom applications. • Made in the USA!
50-FLATWORK ACCESSORIES
Material Specifications Product Description
Product Code No.
2’ x 2’ Yellow Panels
50.20.11220
2’ x 2½’ Yellow Panels
50.20.11225
2’ x 3’ Yellow Panels
50.20.11230
2’ x 2’ Red Panels
50.20.12220
2’ x 2½’ Red Panels
50.20.12225
2’ x 3’ Red Panels
50.20.12230 50.20.16225
2’ x 3’ Black Panels
50.20.16230
PRODUCTS
50.20.16220
70- FOUNDATION
2’ x 2’ Black Panels 2’ x 2½’ Black Panels
60-PRECAST & TILT-UP
• Compressive stress resulting from prestress 220 PSI both directions • Cast Stone compressive strength greater than 9000 psi average at 56 days ASTM C140-98b • Constructed unit flexural strength; modulus of rupture greater than 1200 psi ASTM C293-94 • Absorption less then 5.3% ASTM C140 • Abrasion resistance; Coefficient of loss .1cm3/cm2 ASTM C418-98 • Freeze-Thaw resistance; less than 1% loss after 75 cycles, ASTM C1262d-98, 3% NaCL solution • Mechanical anchor pull out strength greater than 900 lbs each • Mechanical anchor push through strength greater than 1200 lbs each • Slip resistance greater than .8, ASTM C1028-96
10-FORMING & SHORING
ADA DECTECTABLE WARNING PANELS
80- TOOLS & PLACING
www.atlasform.com
159
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
P-24
Contractor Committed.
DELTA TIE SANDWICH PANEL CONNECTOR Special Order Product Code No.
Description
Packaging
5” x 7” TIE
200 per carton
Available in full cartons only.
P-25
P-30
PLASTIC SETTING BOLT Product Code No.
Bolt Dia.
Wt. Lbs. per 100
20.28.60010
1/2”
5.5
20.28.60020
3/4”
8.0
20.28.60030
1”
16.0
COREWALL SLOTTED INSERT, NUT TYPE
40-BAR SUPPORTS
Special Order
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
Part No.
P-31
Galvanized Product Code No.
Epoxy Coated Product Code No.
Wt. Lbs.
CS425
1.9 Ea.
CS625
2.5 Ea.
CS825
3.5 Ea.
CS435
2.2 Ea.
CS635
3.0 Ea.
CS835
4.3 Ea.
CS445
2.9 Ea.
CS645
4.2 Ea.
CS845
5.2 Ea.
COREWALL SLOTTED INSERT, STRAP TYPE
PRODUCTS
Part No.
80- TOOLS & PLACING
70- FOUNDATION
Special Order
160
Galvanized Product Code No.
Epoxy Coated Product Code No.
Wt. Lbs.
SA 1425
2.1 Ea.
SA 1625
2.8 Ea.
SA 1825
3.9 Ea.
SA 1435
2.7 Ea.
SA 1635
3.4 Ea.
SA 1835
4.5 Ea.
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
P-32
Part No.
Galvanized Product Code No.
Epoxy Coated Product Code No.
Wt. Lbs. 1.4 Ea.
CE 806
2.6 Ea.
CE 808
3.8 Ea.
CE 810
2.0 Ea.
CE 812
3.2 Ea.
CE 814
5.4 Ea.
P-51
U.S. Patent No. 4,398,762 Caution: Not interchangeable with other manufacturers’ products. Safe Working Loads-Tons
Product Code No.
Wt. Lbs.
2
60.10.30002
5.0 Ea.
4
60.10.30004
7.5 Ea.
8
60.10.30008
17.0 Ea.
1
30-ATLAS TECH PRODUCTS
SWIFT LIFT® UNIVERSAL LIFTING EYES
20-FORMING ACCESSORIES
CE 804
10-FORMING & SHORING
COREWALL STRAP ANCHOR, STANDARD Special Order
3.0 Ea.
40-BAR SUPPORTS
20
39.0 Ea.
P-50
U.S. Patent No. 3,499,676 Caution: Not interchangeable with other manufacturers’ products. Product Code No.
Wt. Lbs.
2
60.10.25002
5.8 Ea.
4
60.10.25004
9.2 Ea.
8
60.10.25008
17.8 Ea.
60-PRECAST & TILT-UP
Safe Working Loads-Tons
50-FLATWORK ACCESSORIES
SWIFT LIFT® LIFTING EYES
PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
161
P-52
Contractor Committed.
SWIFT LIFT® ANCHORS Made of special high tensile strength steel. Safe Working Loads-Tons
Size Dia. X Length
Plain Product Code No.
Packaging
Wt. Lbs. per 100
1
3/8” x 2-5/8”
60.11.70102
250
13.3
1
3/8” x 3-3/8”
60.11.70103
200
15.5
1
3/8” x 4-3/4”
60.11.70105
200
19.0
1
3/8” x 8”
60.11.70108
100
29.0
1
3/8” x 9-1/2”
60.11.70109
100
38.0
2
9/16” x 2-3/4”
60.11.70202
125
32.0
2
9/16” x 3-3/8”
60.11.70203
125
39.0
2
9/16” x 5-1/2”
60.11.70205
100
51.5
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
2
9/16” x 6”
60.11.70206
100
55.0
2
9/16” x 6-3/4”
60.11.70207
50
61.0
2
9/16” x 11”
60.11.70211
50
96.0
4
3/4” x 3-3/4”
60.11.70403
50
83.0
4
3/4” x 4-1/4”
60.11.70404
50
88.0
4
3/4” x 4-3/4”
60.11.70405
50
96.4
4
3/4” x 5-1/2”
60.11.70406
50
100.0
4
3/4” x 7-1/8”
60.11.70407
25
128.0
4
3/4” x 9-1/2”
60.11.70409
25
157.4
4
3/4” x 14”
60.11.70414
212.0
4
3/4” x 19”
60.11.70419
275.0
8
1-3/32” x 4-3/4”
60.11.70805
215.0
8
1-3/32” x 5-1/4”
8
1-3/32” x 6-3/4”
60.11.70807
275.0
8
1-3/32” x 10”
60.11.70810
395.0
8
1-3/32” x 10-3/8”
8
1-3/32” x 26-3/4”
60.11.70826
883.0
20
1-1/2” x 10”
60.11.72010
970.0
20
1-1/2” x 19-3/4”
60.11.72020
1306.0
461.0
PRODUCTS
P-52-W
P-53
SWIFT LIFT ANCHORS WITH WASHER Safe Working Loads-Tons
Size Dia. X Length
2 Ton
9/16” x 2-3/4”
40.0
4 Ton
3/4” x 3-3/4”
82.0
Product Code No.
Size Dia. X Length
Packaging
Product Code No.
Wt. Lbs. per 100
1
3/8” x 2-5/8”
250
14.0
2
9/16” x 3-1/2”
100
40.0
4
3/4” x 4-3/4”
50
92.0
8
1-3/32” x 7-1/8”
20
20
1-1/2” x 9-5/8”
5
60.11.90500 60.11.91000
290.0
60.11.92000
750.0
For use with 1,2,4,8 & 16 ton hardware, respectively.
162
Wt. Lbs. per 100
SWIFT LIFT® EYE ANCHORS Safe Working Loads-Tons
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
Contact Atlas Construction Supply for concrete strength requirements to develop Safe Working Loads. DOT certified SL Anchors are also available by special order.
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
P-54
FOR USE WITH P-59 SHEAR BARS
Product Code No.
Wt. Lbs. per 100
2 ton
60.10.76200
0.1 Ea.
4 ton
60.10.76400
0.2 Ea.
SWIFT LIFT® NARROW RECESS PLUG
P-56
30-ATLAS TECH PRODUCTS
FOR USE WITH P-63 AND P-64 Special Order Safe Working Loads-Tons
Dia.
1
Narrow Recess Plug Product Code No.
Wt. Lbs.
2-3/8”
200
18.0
2
3”
100
35.0
4
3-3/4”
50
67.6
8
4-3/4”
25
100.0
20
6-3/8”
10
300.0
P-56-PL
USE WITH ANY SWIFT LIFT ANCHOR AND WITH P-66-PL, P-67-PL AND P-68-PL SWIFT LIFT PLUS PLATES. Special Order Plug Dia.
Product Code No.
Packaging
1
2-1/2”
150
2
3-1/4”
150
4
4”
100
8
5”
50
P-56-R
SWIFT LIFT® RECESS PLUGS
60-PRECAST & TILT-UP
Safe Working Loads-Tons
50-FLATWORK ACCESSORIES
SWIFT LIFT® PLUS RECESS PLUG
40-BAR SUPPORTS
Packaging
20-FORMING ACCESSORIES
Size
10-FORMING & SHORING
SWIFT LIFT® THROW AWAY RECESS PLUG
Narrow Recess Plug Product Code No.
Packaging
Wt. Lbs. per 100
1
2-3/8”
60.10.70100
50
13.0
2
3”
60.10.70200
20
25.0
4
3-3/4”
60.10.70400
20
50.0
8
4-3/4”
60.10.70800
20
100.0
20
6-3/8”
10
300.0
www.atlasform.com
80- TOOLS & PLACING
Dia.
PRODUCTS
Safe Working Loads-Tons
70- FOUNDATION
FOR USE WITH P-63-R AND P-66-R
163
P-57
P-58
Packaging
Wt. Lbs.
1
25
0.8 Ea.
2
25
1.5 Ea.
4
20
3.5 Ea.
SWIFT LIFT® RUBBER RING FOR STEEL RECESS PLUG Product Code No.
Packaging
1
P-59
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
Product Code No.
Safe Working Loads-Tons
P-60
PRODUCTS
60-PRECAST & TILT-UP
SWIFT LIFT® STEEL RECESS PLUG Safe Working Loads-Tons
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
Special Order
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
164
Wt. Lbs. per 100
100
1.0
2
60.10.79200
50
2.0
4
60.10.79400
25
3.0
SHEAR BAR FOR SWIFT LIFT ANCHORS For Use With
Rebar Size
1 ton anchor
#4
Product Code No.
Wt. Lbs. per 100
2 ton anchor
#4
4 ton anchor
#4
60.11.12100
173.0
8 ton anchor
#6
60.11.13100
438.0
For Use With
Wire Dia.
Product Code No.
2 ton anchor
0.375
60.11.11200
94.0
4 ton anchor
0.44
60.11.12110
150.0
128.0 156.0
Wt. Lbs. per 100
REINFORCING BAR FOR SWIFT LIFT ANCHORS For Use With
Rebar Size
1 ton anchor
.306 wire
2 ton anchor
#3
4 ton anchor
#5
Product Code No.
Wt. Lbs. per 100 82.0 75.0
60.11.10305
134.0
8 ton anchor
#6
60.11.10306
600.0
20 ton anchor
#8
60.11.10308
1913.0
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
P-61
Special Order Safe Working Loads-Tons
Product Code No.
Wt. Lbs. / Ea.
4
25
42.0
8
25
66.0
SWIFT LIFT® COUNTERSUNK SCREW
P-62
20-FORMING ACCESSORIES
Packaging
10-FORMING & SHORING
SWIFT LIFT® SETTING PLATE WITH COUNTERSUNK SCREW
Special Order For Use With 4 ton
7/16” x 3/4”
8 ton
30-ATLAS TECH PRODUCTS
Size 5/16” x 3/4”
Product Code No.
SWIFT LIFT® STUD
P-63
Size Dia. X Length
Product Code No.
Packaging
Wt. Lbs. per 100
1
5/16” x 3”
100
9.0
2
7/16” x 3”
50
23.0
4
7/16” x 3”
50
28.0
8
7/16” x 3”
25
30.0
20
12mm x 3-3/4”
10
60.0
For Wing Nut see P-64, Use with P-56 & P-56-R Recess Plug.
SWIFT LIFT® PLUS HOLDING STUD WITH WING NUT
P-63-PL
Safe Working Loads-Tons
Stud Dia. X Length
Packaging
2, 4, & 8
3/8” x 6”
50
60-PRECAST & TILT-UP
Special Order Product Code No.
FOR USE WITH P-56-R RECESS PLUG AND P-56-R ATTACHMENT NUT Special Order Fixed
Product Code No.
Wt. Lbs.
1
8mm
0.15 Ea.
2
12mm
0.15 Ea.
4
12mm
0.15 Ea.
8
12mm
0.15 Ea.
www.atlasform.com
Free NC Thread
80- TOOLS & PLACING
Stud Dia.
PRODUCTS
P-63-R
70- FOUNDATION
SWIFT LIFT® ATTACHMENT STUD WITH WING NUTS Safe Working Loads-Tons
50-FLATWORK ACCESSORIES
Safe Working Loads-Tons
40-BAR SUPPORTS
Special Order
165
Contractor Committed.
SWIFT LIFT® WING NUT
P-64
Special Order
P-64-PL
5/16”
1 ton
7/16”
2, 4 & 8 ton
12mm
20 ton
Product Code No.
Size
Product Code No.
Dia.
Packaging
2, 4 & 8 ton
60.10.28208
3/8” dia. Coil
50
Special Order FOR USE IN SL LIFTING EYE Safe Working Loads-Tons
Wt. Lbs. per 100
1
3.0
2
6.0
4
20.0
8
24.0
20
47.0
50-FLATWORK ACCESSORIES
Special Order FOR USE IN SL RECESS PLUG
P-66-PL P-67-PL P-68-PL
Safe Working Loads-Tons
Tapped for Bolt Size
Packaging
Wt. Lbs. per 100
1 2
5/16” dia.
50
2.0
7/16” dia.
50
5.0
4
7/16” dia.
50
9.0
8
7/16” dia.
25
16.0
20
5/8” dia.
10
38.0
Product Code No.
SWIFT LIFT® PLUS PLATES USE WITH P-56-L SWIFT LIFT PLUS RECESS PLUGS ONLY Type
Product Code No.
Safe Working Loads-Tons 1
.75” x 1.5”
P-66-PL
60.10.21222
2
.75” x 1.6875”
P-66-PL
60.10.21241
4
.822” x 1.6875”
3/8” Dia. NC Threads
P-66-PL
8
.822” x 2.375”
P-67-PL †
1
.75” x 1.5” x 4”
P-67-PL †
60.10.21221
2
.75” x 1.6875” x 4”
P-67-PL †
60.10.21242
4
.822” x 1.6875” x 4”
P-67-PL †
60.10.21281
8
.822” x 2.375” x 4”
P-68-PL †
1
.625” x 1.75”
P-68-PL †
2
.875” x 2.5”
P-68-PL †
4
1.375” x 3.25”
P-68-PL †
8
1.75” x 3.75”
P-67-PL SL Plus Stud Plate
P-68-PL Sl Plus Holding Plate
† Use P-64-PL Wing Nut
166
Plate Size Width X Length
P-66-PL 4”
80- TOOLS & PLACING
Product Code No.
SWIFT LIFT® TAPPED PLATE
PRODUCTS
60-PRECAST & TILT-UP
Safe Working Loads-Tons
SWIFT LIFT® SAFETY PIN WITH WASHER
P-65
P-66
70- FOUNDATION
Size
SWIFT LIFT® PLUS COIL WING-NUT
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
Special Order
Thread Size
Product Code No.
Wt. Lbs.
1
8 mm
0.2 Ea.
2
12 mm
0.2 Ea.
4
12 mm
0.3 Ea.
8
12 mm
0.3 Ea.
SWIFT LIFT® PLUS MAGNETIC SETTING Special Order For use with P-56-L Recess Plug only. Size
Product Code No.
P-69-M P-56-MS
Wt. Lbs. 0.56 Ea.
4 Ton
0.63 Ea.
8 Ton
1.06 Ea.
30-ATLAS TECH PRODUCTS
2 Ton
P-56-MS Screw for Swift Lift Plus Magnetic Setting Plate. 3/8”- 16 NC x 3/4” Allen Head Screw. Product Code No.
20-FORMING ACCESSORIES
Safe Working Loads-Tons
P-66-R
10-FORMING & SHORING
SWIFT LIFT® ATTACHMENT NUTS
Wt. Lbs. 0.03 Ea.
Size
With 8ft. Sling Product Code No.
40-BAR SUPPORTS
P-74
PIPE TURNING DEVICE Special Order
4 Ton
P-75 UTILITY ANCHOR B
Type
Product Code No.
Wt. Lbs.
3-1/8”
4UA444
60.11.50014
0.32 Ea.
6”
3-3/4”
5UA444
60.11.50015
0.75 Ea.
6-7/16”
3-3/4”
5UA671
60.11.50215
1.00 Ea.
7-3/8”
4-3/4”
6UA444
60.11.50016
0.75 Ea.
7-9/16”
4-3/4”
6UA671
60.11.50216
1.00 Ea.
9-7/8”
6-3/4”
8UA671
60.11.50218
1.50 Ea.
60-PRECAST & TILT-UP
A 5-1/4”
P-75 P-76
50-FLATWORK ACCESSORIES
8 Ton
P-75-DOT is also available
Description .444 Anchor
Product Code No.
Wt. Lbs. 1.34 Ea.
45 Degrees
.444 Anchor
1.34 Ea.
90 Degrees
.671 Anchor
1.34 Ea.
45 Degrees
.671 Anchor
1.34 Ea.
PRODUCTS
Type 90 Degrees
Dimensions
Product Code No.
Pieces per box
Wt. Lbs. per box
2-1/2” x 5-1/2” x 1/2”
60.25.81000
400
40.0
www.atlasform.com
167
80- TOOLS & PLACING
P-78
PANEL PADS
70- FOUNDATION
P-76 UTILITY ANCHOR SETTING PLUG
P-80
30-ATLAS TECH PRODUCTS
Product Code No.
Pieces per carton
Wt. Lbs. per carton
1/16” x 2” x 4” or 1/16” x 4” x 4”
2000
39.0
1000
39.0
1/8” x2” x 4” or 1/8” x 4” x 4”
2000
78.0
1000
78.0
1/4” x 2” 4” or 1/4” x 4” x 4”
1000
78.0
500
78.0
1-16” x 3” x 3”
2000
44.0
1/8” x 3” x 3”
2000
86.0
1/4” x 3” x 3”
1000
86.0
Available in full cartons only. Other sizes available on request. Note: Each 2” x 4” or 4” x 4” sheet is scored every 2” of the 24” width; each 3” x 3” sheet is scored every 3” of the 24” width.
40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
HEAVY DUTY SHIMPACKS Item and Size
Product Code No.
1-1/16” x 4” x 6”
60.25.71020
Pieces per Carton
Wt. Lbs. per Carton
50
50.0
1-1/16” x 4” x 4”
100
65.0
1-1/16” x 3” x 3”
100
39.0
1-1/16” x 6” x 6”
50
71.0
1-1/8” x 4” x 6”
60.25.71010
GTI Shimpacks 4” x 6”
60.25.72020
Available in full cartons only Note: 1-1/16” x 4” x 6” and 1-1/16” x 4” x 4” Shimpaks are made by shim thickness of one 1/16” thick, three 1/4” thick and two 1/8” thick, in that order. Shimpaks are held together with a resilient band to make removal or addition easy.
P-82
BEARING STRIPS (NON-SKID) Item and Size
PRODUCTS
60-PRECAST & TILT-UP
SHIM STRIPS Item and Size
P-81
Pieces per Carton
Wt. Lbs. per Carton
1/2” x 2” x 48”
1200 LF
135.0
1/4” x 2” x 48”
600 LF
135.0
1/8” x 2” x 48”
Product Code No.
60.25.81224
Available in full cartons only Note: Each carton of 48” contains 25 scored sheets, which offer 300 2” x 48” strips; Other thicknesses, lengths and scoring available on special order; non-skid bearing strips are not designed for stacking.
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
168
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
P-83
Thickness
Size
1/16” 1/8”
Product Code No.
Wt. Lbs. per Carton
2” x 3”
1000
10.0
2” x 3”
1000
20.0
1/4”
2” x 3”
500
20.0
1/16”
3” x 4”
1000
22.0
1/8”
3” x 4”
1000
44.0
1/4”
3” x 4”
500
44.0
20-FORMING ACCESSORIES
Pieces per Carton
Minimum order 100 pieces of each thickness and size. Other sizes available on special order. Note: Slot width 13/16”.
Dia.
400
4”
600
6”
800
8”
P-84
Product Code No.
Plugs per Carton
Wt. Lbs. per Carton
1000
27.0
60.25.86600
2000
84.0
1000
72.0
Special Order Product
Thread Size x Insert Length
Qty. Per Carton
Wt. Lbs. Per Carton
P10T
10-24 x 11/16”
1000
7.0
P15T
1/4” x 1-1/2”
1000
45.5
Product Code No.
P-86 Standard Style
3/8” x 1”
500
22.0
P25T
3/8” x 1-3/8”
400
32.2
P35T
1/2” x 1-1/2”
150
40.5
P36T
1/2” x 2-7/8”
50
27.1
P45T
5/8” x 1-11/16”
150
46.6 36.4
50
3/4” x 1-11/16”
50
11.5
P56T
3/4” x 3”
50
23.8
P25TOB
3/8” X 1-3/8”
400
23.5
P35TOB
1/2” X 1-1/2”
150
35.2
P25A
3/8”
500
7.9
P35A
1/2”
100
3.8
P45A
5/8”
100
7.8
P55A
3/4”
100
5.2
1/2”
100
18.8
20.42.85302
PRODUCTS
5/8” x 2-7/8”
P55T
P-86 Open Bottom Style
70- FOUNDATION
P46T
60-PRECAST & TILT-UP
P24T
P-86 P-87 P-88
50-FLATWORK ACCESSORIES
STAR INSERTS AND ACCESSORIES
40-BAR SUPPORTS
Core Plugs are designed for manufacturers of prestressed hollow core planks. They are lightweight, easy to insert and effectively block off grout flow to ensure bearing through the ends of the planks onto the sill and foundation. The exclusive “wall” taper design of these plastic core plugs assures a tight interference fit. Core Plugs are available for most sizes of spancrete, flexicore, spiroll, dycore and dynaspan. Other shapes and sizes are available. Plug numbers refer to the diameter of the core holes and not to the thickness of the plank.
30-ATLAS TECH PRODUCTS
KOROLATH CORE PLUGS No.
10-FORMING & SHORING
HORSESHOE SPACER STRIPS Special Order
P-87 Star Adapter Plug
80- TOOLS & PLACING
20.42.85301
P-88 Star Holzin Insert HOLZIN
www.atlasform.com
169
P-91-S P-91-NC P-91-RB
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
FLEET LIFT® RING CLUTCH STANDARD Special Order Load Range
Length
2-3 ton
10.38”
Pieces per Box
Wt. Lbs. Ea.
Each
3.65
4-6 ton
12.50”
Each
8.65
8-10 ton
16.50”
Each
19.87
P-91 Ring Clutch Standard
Special Order Load Range
Length
Pieces per box
Wt. Lbs. Ea.
2-3 ton
30”
Each
3.65
4-5 ton
36”
Each
8.65
8-10 ton
36”
Each
19.87
Product Code No.
FLEET LIFT® RING CLUTCH HANDLE Special Order Load Range
P-92 P-92-P P-92-DP P-92-AH
Pieces per Box
Wt. Lbs. Each
3 ton
Each
0.35
6 ton
Each
0.65
10 ton
Each
1.75
Product Code No.
FLEET LIFT® ERECTION ANCHOR Special Order Load Range
Length
Product Code No.
Pieces per drum
Wt. Lbs. per 100
2 ton
8.38”
450
225
4 ton
11.88”
200
541
6 ton
13.25”
100
909
8 ton
13.25”
100
1046
P-92 Erection Anchor with Shear Plate
Length
Product Code No.
Pieces per drum
Wt. Lbs. per 100
2 ton
8.38”
300
225
4 ton
11.88”
150
541
6 ton
13.25”
75
909
8 ton
13.25”
75
1046
Load Range
PRODUCTS
70- FOUNDATION
FLEET LIFT® ERECTION ANCHOR
80- TOOLS & PLACING
P-92 Erection Anchor
FLEET LIFT® ERECTION ANCHOR WITH SHEAR PLATE Load Range
60-PRECAST & TILT-UP
Product Code No.
FLEET LIFT® RING CLUTCH WITH CABLE BALL
30-ATLAS TECH PRODUCTS 40-BAR SUPPORTS 50-FLATWORK ACCESSORIES
Contractor Committed.
P-92-DP Erection Anchor with Double Shear Plate/Pin
Length
Product Code No.
Pieces per drum
Wt. Lbs. per 100
2 ton
8.38”
300
242
4 ton
11.88”
150
583
6 ton
13.25”
75
951
8 ton
13.25”
75
1088
FLEET LIFT® ERECTION ANCHOR Load Range
P-92-AH Erection Anchor with 45º Head with Shear Plate
170
Length
Product Code No.
Pieces per drum
Wt. Lbs. per 100
2 ton
8.50”
300
230
4 ton
11.25”
150
550
8 ton
13.75”
75
1050
www.atlasform.com
WITH DOUBLE SHEAR PLATE/PIN
WITH 45 DEGREE HEAD SHEAR PLATE
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
Length
2 ton
4.38”
Product Code No.
Pieces per drum 1770
Wt. Lbs. per 100 72.0
2 ton
8.38”
450
162.0
4 ton
7.50”
400
280.0
4 ton
11.88”
200
419.0
6 ton
13.25”
100
769.0
8 ton
13.25”
100
923.0
P-92-H Two-Hole Erection Anchor
FLEET LIFT® TWO HOLE ERECTION ANCHOR WITH SHEAR PLATE Special Order Length
2 ton
4.38”
Product Code No.
Pieces per drum 500
Wt. Lbs. per 100 118
2 ton
8.38”
300
208
4 ton
7.50”
200
366
4 ton
11.88”
200
505
6 ton
13.25”
100
875
8 ton
13.25”
100
1029
P-92-HP Two-Hole Erection Anchor with Shear Plate
P-92-S P-92-SP
Special Order
Width
Pieces per drum
Wt. Lbs. per 100
4 ton
6.00”
Product Code No.
400
317
8 ton
6.00”
200
554
8-10 ton
7.00”
100
1049
8-10 ton
8.00”
100
1450
P-92-S Sandwich Panel Erection Anchor
Special Order Load Range
Width
4 ton
Product Code No.
6.00”
400
349
8 ton
6.00”
200
586
8-10 ton
7.00”
100
898
8-10 ton
8.00”
100
940
P-92-SP Sandwich Panel Erection Anchor with Shear Plate
FLEET LIFT® L-ANCHOR
P-93
Special Order Length
1 ton
4.00”
Product Code No.
Pieces per drum
Wt. Lbs. per 100
2025
30
80- TOOLS & PLACING
Load Range
P-93 L-Anchor
www.atlasform.com
PRODUCTS
Wt. Lbs. per 100
70- FOUNDATION
Pieces per drum
60-PRECAST & TILT-UP
FLEET LIFT® SANDWICH PANEL ERECTION ANCHOR WITH SHEAR PLATE
50-FLATWORK ACCESSORIES
Load Range
40-BAR SUPPORTS
FLEET LIFT® SANDWICH PANEL ERECTION ANCHOR
30-ATLAS TECH PRODUCTS
Load Range
20-FORMING ACCESSORIES
Load Range
10-FORMING & SHORING
FLEET LIFT® TWO-HOLE ERECTION ANCHOR P-92-H Special Order P-92-HP
171
P-94
30-ATLAS TECH PRODUCTS 40-BAR SUPPORTS 50-FLATWORK ACCESSORIES 60-PRECAST & TILT-UP
Contractor Committed.
FLEET LIFT® T-ANCHOR Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
P-95-F
Load Range
Length
Pieces per drum
Wt. Lbs. per 100
2 ton
4.25”
Product Code No.
1500
63.0
2 ton
5.75”
800
83.0
4 ton
4.25”
700
135.0
4 ton
4.75”
550
148.0
4 ton
5.25”
500
161.0
4 ton
5.75”
425
175.0
4 ton
6.25”
400
188.0
4 ton
6.75”
375
201.0
4 ton
7.25”
325
215.0
4 ton
7.75”
300
228.0
4 ton
8.25”
275
241.0
4 ton
8.75”
250
254.0
4 ton
9.25”
225
268.0
4 ton
9.75”
200
281.0
4 ton
10.25”
175
294.0
4 ton
10.75”
150
309.0
4 ton
11.25”
150
321.0
6 ton
11.50”
175
486.0
8 ton
6.25”
250
321.0
8 ton
11.50”
175
576.0
FLEET LIFT® FLAT FOOT ANCHOR Special Order
P-95-F Flat Foot Anchor
P-95-P
Load Range
Length
2 ton 2 ton 3 ton
3.75”
8 ton
6.25”
Product Code No.
Pieces per drum
Wt. lbs. per 100
2.75”
2000
50
3.38”
1500
58
1050
92
Use P-94 8 ton anchor
FLEET LIFT® PLATE ANCHOR
PRODUCTS
70- FOUNDATION
Special Order Length
Product Code No.
Pieces per drum
2 ton
2.25”
1600
71
4 ton
3.00”
500
142
4 ton
3.50”
500
155
4 ton
4.38”
500
196
8 ton
6.88”
250
436
80- TOOLS & PLACING
P-95-P Plate Anchor
Load Range
172
www.atlasform.com
Wt. lbs. per 100
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
P-96
Special Order Load Range
Length
2 ton
Product Code No.
Wt. lbs. per 100
4.00”
1200
42
2 ton
2.75”
1200
27
4 ton
5.50”
1125
123
8 ton
7.00”
400
331
P-96 Two-Hole Anchor
FLEET LIFT® DOUBLE TEE SPECIALTY ANCHOR
P-97-DT
30-ATLAS TECH PRODUCTS
Special Order Load Range
Length
4 ton 8 ton
Product Code No.
Pieces per drum
Wt. lbs. per 100
16.50” to 23.50”
100
300
22.25” to 32.25”
60
700
P-97-DT Shear Bar
Special Order Load Range
Length
Product Code No.
Pieces per drum
Wt. lbs. per 100
2 ton
14.75”
450
98
4 ton
14.75”
400
107
8 ton
14.75”
400
123
P-98-S Shear Bar
P-98-T
Special Order Load Range
Overall Length
Product Code No.
Wt. Lbs. per 100
2 ton
#3
36”
112.6
4 ton
#4
48”
267.0
8 ton
#6
72”
901.1
2 ton
#3
33”
103.2
4 ton
#4
42”
233.6
8 ton
#6
66”
826.0
2 ton
#3
30”
93.8
4 ton
#4
36”
200.2
8 ton
#6
54”
675.8
PRODUCTS
1500 PSI
2000 PSI
80- TOOLS & PLACING
P-98-T Tension Reinforcement
3000 PSI
www.atlasform.com
70- FOUNDATION
Grade 60 Rebar Size
60-PRECAST & TILT-UP
FLEET LIFT® TENSION BAR
50-FLATWORK ACCESSORIES
P-98-S
40-BAR SUPPORTS
Note Anchor Length Required: 4 ton: Tee Depth Minus 1.50”. 8 ton: Tee Depth Minus 1.75”.
FLEET LIFT® SHEAR BAR
20-FORMING ACCESSORIES
Pieces per drum
10-FORMING & SHORING
FLEET LIFT® TWO-HOLE ANCHOR
173
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
P-99 P-99-N
P-99 Urethane Recess Plug
P-99-C
Contractor Committed.
FLEET LIFT® REUSABLE RECESS PLUG URETHANE REUSABLE WITH 3/8” COIL THREAD
Special Order Type
Product Description
Load Range
Length
P-99-N
Narrow Recess
1 ton
4”
Product Code No.
Pieces per box
Wt. Lbs. per 100
50
23.0
P-99
Plastic Recess
2-3 ton
4”
50
22.0
P-99
Plastic Recess
4-6 ton
5-1/4”
50
60.0
P-99
Plastic Recess
8-10 ton
7-1/2”
25
155.0
FLEET LIFT® CAST STEEL RECESS PLUG CAST STEEL WITH 1/2” COIL THREAD
30-ATLAS TECH PRODUCTS
Special Order
P-99-C Cast Steel Recess Plug
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
P-100
Type
Product Description
Load Range
Length
Product Code No.
Pieces per box
Wt. Lbs. per 100
P-99-C
Cast Recess
2 ton
4”
50
72.0
P-99-C
Cast Recess
4-6 ton
5-1/4”
50
122.0
P-99-C
Cast Recess
8 ton
7-1/2”
10
350.0
Pieces per box
Wt. Lbs. per 100
FLEET LIFT® HOLDING PLATE FOR USE WITH P-99-N Special Order
P-100 Holding Plate
P-101
Type
Product Description
Load Range
Length
Product Code No.
P-100
Holding Plate
2 ton
2-3/4”
50
15.0
P-100
Holding Plate
4-6 ton
3-3/8”
50
25.0
P-100
Holding Plate
8 ton
4-7/8”
25
59.0
Pieces per box
Wt. Lbs. per 100
FLEET LIFT® HOLDING ROD FOR USE WITH P-99 AND P-99-C Special Order
P-101 Holding Rod
P-102
Type
Product Description
Load Range
Length
Product Code No.
P-101
Holding Rod
3/8” Coil
6”
50
25.0
P-101
Holding Rod
1/2” Coil
6”
50
42.0
FLEET LIFT® WEDGE FOR USE WITH P-99-C Special Order
P-102 Wedge
P-103 P-103 Foam
174
Type
Product Description
Load Range
Product Code No.
Pieces per box
Wt. Lbs. per 100
P-102
Wedge
2 ton
50
13.0
P-102
Wedge
4-6 ton
50
38.0
P-102
Wedge
8 ton
10
94.0
Pieces per box
Wt. Lbs. per 100
FOAM FOR USE WITH P-99-C Type
Product Description
Load Range
Product Code No.
P-103
Foam
2 ton
60.10.47002
1000
5.0
P-103
Foam
4-6 ton
60.10.47004
1000
5.0
P-103
Foam
8 ton
60.10.47008
500
20.0
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
T-1
WITH PLASTIC TIPPED LEGS OR STAINLESS STEEL TIPS See F-53 Thin Slab Insert for 3/4” Dia. Pickup Inserts Slab Thickness
Product Code No.
Wt. Lbs. per 100
1”
5-1/2”
60.21.53055
131.0
1”
6”
60.21.53060
133.0
1”
6-1/2”
60.21.53065
135.0
1”
7”
60.21.53070
136.0
1”
7-1/4”
1”
7-1/2”
60.21.53075
138.0
1”
8”
60.21.53080
139.0
Product Code No.
Wt. Lbs. per 100
20-FORMING ACCESSORIES
Dia.
137.0
Slab Thickness Up to 5-1/2”
190.0
1-1/4”
6”
192.0
1-1/4”
6-1/2”
193.0
1-1/4”
7”
1-1/4”
7-1/2”
Alternate leg design
30-ATLAS TECH PRODUCTS
Dia. 1-1/4”
195.0 60.21.52075
196.0
1-1/4”
8”
60.21.52080
198.0
1-1/2”
Up to 5-1/2”
60.21.51055
207.0
6”
60.21.51060
209.0
1-1/2”
6-1/2”
60.21.51065
210.0
1-1/2”
7”
60.21.51070
211.0
1-1/2”
7-1/2”
60.21.51075
213.0
1-1/2”
8”
60.21.51080
215.0
40-BAR SUPPORTS
1-1/2”
WITH PLASTIC TIPPED LEGS OR STAINLESS STEEL TIPS Dia.
Slab Thickness
Product Code No.
Wt. Lbs. per 100
300.0
1” Double Pickup Insert 1”
Up to 5-1/2”
60.21.63055
1”
6”
60.21.63060
304.0
1”
6-1/2”
60.21.63065
306.0
7”
60.21.63070
310.0
1”
7-1/2”
60.21.63075
312.0
1”
8”
60.21.63080
316.0
60-PRECAST & TILT-UP
1”
1-1/4” Double Pickup Insert 60.22.62070
7”
60.22.60277
1-1/4”
8”
60.22.60280
1-1/4”
8”
60.22.60287
1-1/4”
8”
60.22.60288
1-1/4”
8”
60.22.60289
1-1/4”
9”
60.22.60297
1-1/4”
10”
60.22.62100
1-1/4”
12”
60.22.62120
PRODUCTS
7”
1-1/4”
70- FOUNDATION
1-1/4”
50-FLATWORK ACCESSORIES
T-2
DOUBLE PICKUP INSERT
10-FORMING & SHORING
SINGLE PICKUP INSERT
1-1/2” Double Pickup Insert Up to 5-1/2”
60.22.61055
461.0
1-1/2”
6”
60.22.61060
465.0
1-1/2”
6-1/2”
1-1/2”
7”
473.0
1-1/2”
7-1/2”
477.0
1-1/2”
8”
481.0
80- TOOLS & PLACING
1-1/2”
469.0
www.atlasform.com
175
T-3
DOUBLE EDGE PICKUP INSERT Dia.
T-3-A
Loop Length
Product Code No.
Wt. Lbs. per 100
3/4”
9”
263.0
3/4”
12”
296.0
1”
12”
1-1/4”
12”
60.21.73002
330.0 350.0
SINGLE EDGE PICKUP INSERT Special Order Dia.
T-4
Loop Length
Product Code No.
Wt. Lbs. per 100
3/4”
9”
153.0
3/4”
12”
157.0
1”
12”
1-1/4”
12”
60.21.73001
175.0 185.0
BRACE ANCHOR FOR FILL Dia.
Slab Thickness
Product Code No.
3/4”
4”
60.22.35040
3/4”
4-1/2”
60.22.35045
3/4”
5”
60.22.35050
3/4”
5-1/2”
60.22.35055
3/4”
6”
60.22.35060
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
Contractor Committed.
Special Order
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
176
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
Dia.
Product Code No.
Wt. Lbs. per 100
3/4”
60.22.15030
80.0
T-6-A
Slab Thickness
Product Code No.
3/4”
4”
60.22.25040
3/4”
5”
60.22.25050
3/4”
5-1/2”
60.22.25055
3/4”
6”
60.22.25060
3/4”
6-1/2”
60.22.25065
7”
60.22.25070
3/4”
7-1/4”
60.22.25072
3/4”
7-1/2”
60.22.25075
3/4”
8”
60.22.25080
3/4”
8-1/4”
60.22.25082
3/4”
8-1/2”
60.22.25085
3/4”
8-3/4”
60.22.25088 60.22.25090
9-1/4”
60.22.25092
3/4”
9-1/2”
60.22.25095
3/4”
10”
60.22.25100
3/4”
10-1/2”
60.22.25105
3/4”
11”
60.22.25110
3/4”
11-1/4”
60.22.25112
3/4”
11-1/2”
60.22.25115
3/4”
12”
60.22.25120
3/4”
15”
60.22.25150
3/4”
16”
60.22.25160
60-PRECAST & TILT-UP
9”
3/4”
50-FLATWORK ACCESSORIES
3/4”
40-BAR SUPPORTS
3/4”
30-ATLAS TECH PRODUCTS
Dia.
20-FORMING ACCESSORIES
BRACE ANCHOR
T-5-A
10-FORMING & SHORING
INVERTED BRACE ANCHOR
T-8
LIFTING ANGLE Bolt Size
Product Code No.
Wt. Lbs.
21”
1-1/4” & 1-1/2”
60.20.41008
53.0 Ea.
18”
1”
PRODUCTS
Length
45.0 Ea.
70- FOUNDATION
For Edge Lifting Plate see T-27.
80- TOOLS & PLACING
www.atlasform.com
177
T-10
T-11
Coil Tie Strut
Shear bar Length
Product Code No.
Wt. Lbs. / Ea.
1”
9”
2
12”
2.17
1-1/4”
10”
2
12”
2.47
1”
9”
4
12”
2.95
1”
12”
4
12”
3.47
1”
15”
4
12”
4.0
DOUBLE END PICKUP INSERT Dia.
T-12
Insert Length
Coil Tie Strut
Shear bar Length
Product Code No.
Wt. Lbs. per 100
1”
9”
2
24”
302.0
1-1/4”
10”
2
24”
435.0
1”
9”
4
24”
457.0
1”
12”
4
24”
560.0
1”
15”
4
24”
664.0
SWIVEL LIFTING PLATE For Double Swivel Lifting Plate see T-26.
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
Insert Length
Special Order
60-PRECAST & TILT-UP PRODUCTS
SINGLE END PICKUP INSERT Dia.
T-13
70- FOUNDATION
Contractor Committed.
Special Order
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
Bolt Dia.
Product Code No.
Wt. Lbs. / Ea.
3/4”
60.20.20001
14.0
1”
60.20.20002
14.0
COIL-ANCHORTM U.S. Patent No. 5,006,023
T-13-L
Dia.
Length
Product Code No.
Wt. Lbs.
Packaging
T-13 Coil-Anchor Set
3/4”
4-1/2”
60.25.15150
0.8 Ea.
20 sets per carton
T-13 Coil-Anchor
3/4”
6”
60.25.15060
1.0 Ea.
20 sets per carton
Extra tangs
3/4”
60.25.15000
4.0 per 100
100 per bag
SET-EEZTM LUBRICANT FOR T-13 COIL ANCHOR BOLT
80- TOOLS & PLACING
Special Order Product Code No.
178
Wt. Lbs.
Packaging
0.4 Ea.
6 oz. bottle
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
Including Telescoping Pipe Type
Adjustment
Wt. Lbs.
Regular Pipe Brace
13 ft. 0” to 20 ft. 6”
96.0 Ea.
T-14, B-4
Heavy-Duty Regular Pipe Brace
14 ft. 0” to 23 ft. 6”
130.0 Ea.
T-14, B-5
Heavy-Duty Long Pipe Brace
22 ft. 6” to 39 ft. 0”
208.0 Ea.
T-14, B-6
Short Pipe Brace
10 ft. 0” to 14 ft. 0”
75.0 Ea.
T-14, B-7
Jumbo Brace
15 ft. 0’ fixed length
107.0 Ea.
Jumbo Brace
22 ft. 0” fixed length
130.0 Ea.
T-14, B-9
Jumbo Brace with 5 ft. extension
27 ft. 0” fixed length
172.0 Ea.
T-14, B-10
Jumbo Brace with 10 ft. extension
32 ft. 0” fixed length
193.0 Ea.
T-14, B-11
Tru-Itt Brace
25 ft. 5” to 40 ft. 0”
505.0 Ea.
T-14, B-12
Jumbo Brace
32 ft. 0” fixed length
245.0 Ea.
B-12 Brace with 10 ft. extension
42 ft. fixed length
382.0 Ea.
T-14, B-15
B-12 Brace with two 10 ft. extensions
52 ft. fixed length
410.0 Ea.
T-14, B-17
B-17 Superior Brace
32 ft. to 42 ft.
668.0 Ea.
T-14, B-18
B-18 Superior Brace
42 ft. to 52 ft.
855.0 Ea.
Adjustment
Wt. Lbs.
T-15
Extension Pipe for B-2 Brace
21 ft. 6” to 29 ft. 0”
71.0 Ea.
T-15
Extension Pipe for B-8 Brace
5 ft 0” extension
42.0 Ea.
T-15
Extension Pipe for B-8 Brace
10 ft 0” extension
63.0 Ea.
T-15-C
Coupler for B-8 Brace
21.0 Ea.
T-20
Extension for B-12 Brace
100.0 Ea.
T-20-C
Coupler for B-12 Brace
65.0 Ea.
Size
Wt. Lbs.
Adjustable from 7 ft. 6” to 8 ft. 10”
55.0 Ea.
T-19
50-FLATWORK ACCESSORIES
ON-SITE PIPE BRACE
40-BAR SUPPORTS
T-14, B-14
30-ATLAS TECH PRODUCTS
T-14, B-8
20-FORMING ACCESSORIES
T-14, B-2
Type
T-14 T-15
10-FORMING & SHORING
STANDARD PIPE BRACE ASSEMBLIES
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
www.atlasform.com
179
T-21
Bolt Dia.
Color
3/4” 1”
Product Code No.
Wt. Lbs. Ea.
Packaging
Orange
0.2
50 per carton
Red
0.3
50 per carton
1-1/4”
Red
0.3
50 per carton
1-1/2”
Green
0.4
40 per carton
Available in full cartons only, sold in sets only. Note: Not recommended for contractors (except in emergency) to put in inserts in field Buy inserts with Locator Plug installed
T-26
DOUBLE SWIVEL LIFTING PLATE For smaller sizes see T-12 Swivel Lifting Plate Bolt Dia.
Product Code No.
Wt. Lbs.
1-1/4”
60.20.20011
16.1 Ea.
1-1/2”
60.20.20012
16.1 Ea.
1”
8.0 Ea.
1” Bushing
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
INSERT LOCATOR PLUG
T-27
-
EDGE LIFTING PLATE FOR 3/4” AND 1” DIA. BOLTS Product Code No.
Wt. Lbs.
60.20.41027
23.0 Ea.
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
Contractor Committed.
FOR COIL INSERTS Special Order
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
180
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
Wt. Lbs. per 100
Packaging
5”
60.21.20500
160
20
5-1/4”
60.21.20525
5-1/2”
60.21.20550
165
20
6”
60.21.20600
170
20
6-1/4”
60.21.20625
172.5
20
6-1/2”
60.21.20650
175
20
6-3/4”
60.21.20675
7”
60.21.20700
180
20
7-1/4”
60.21.20725
182.5
20
7-1/2”
60.21.20750
185
20
190
20
253
10
60.21.20800 60.21.20825
8-1/2”
60.21.20850
8-3/4”
60.21.20875
9”
60.21.20900
256
10
9-1/4”
60.21.20925
258
10
9-1/2”
60.21.20950
259
10
10”
60.21.21000
262
10
10-1/2”
60.21.21050
265
10
60.21.21100
302
10
60.21.21150
304
10
12”
60.21.21200
306
10
15”
60.21.21500
24”
60.21.22400
50-FLATWORK ACCESSORIES
11” 11-1/2”
40-BAR SUPPORTS
8” 8-1/4”
Plastic Base Product Code No.
30-ATLAS TECH PRODUCTS
Wire Base Product Code No.
20-FORMING ACCESSORIES
Structural Panel Thickness
T-41 T-41-S
T-43-R
Wt. Lbs.
60.20.10100
9.7 Ea.
PRODUCTS
Product Code No.
70- FOUNDATION
REPLACEMENT T-43 LIFTING HARDWARE U.S. Patent No. 4,703,595 and 4,769,960 and Design 344,836
60-PRECAST & TILT-UP
Requires a minimum concrete compressive strength of 2,500 psi. Ground Release II Inserts are shipped assembled (ready to use). Each Insert is sized 1/8” less than the panel thickness above. When ordering, specify overall panel thickness including structural thickness and aggregate or form liner thickness. Available in other sizes upon request.
GROUND RELEASETM LIFTER
10-FORMING & SHORING
GROUND RELEASE IITM INSERT
80- TOOLS & PLACING
www.atlasform.com
181
T-45
Product Code No.
Wt. Lbs.
Packaging
1.3 per bag
20 per bag
3/4” Brace anchor cap for use with T-6-A Product Code No.
T-46
Wt. Lbs.
Packaging
0.5 per bag
20 per bag
GROUND RELEASE IITM SPREADER BEAM WITH 2 SHACKLES FOR USE WITH T-43-R LIFTING HARDWARE Special Order Product Code No.
Wt. Lbs. 38.0 Ea.
T-49
GYRO TILT PLUSTM FACE LIFT INSERT Special Order Structural Panel Thickness
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
GROUND RELEASE IITM PATCH CAPS For use with T-41 and T-49 Insert Recess
60-PRECAST & TILT-UP PRODUCTS
70- FOUNDATION
Contractor Committed.
FOR USE WITH T-41 AND T-49 Special Order
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
T-49-E
Product Code No.
Packaging
5”
160.0
20
5-1/2”
165.0
20
6”
170.0
20
6-1/4”
172.5
20
6-1/2”
175.0
20
7”
180.0
20
7-1/4”
182.5
20
7-1/2”
185.0
20
8”
190.0
20
8-1/2”
253.0
20
9”
256.0
20
9-1/4”
257.5
20
9-1/2”
259.0
20
10”
262.0
20
10-1/2”
265.0
20
11”
248.0
20
11-1/2”
271.0
20
12”
224.0
20
GYRO TILT PLUSTM EDGE LIFT INSERT Special Order
80- TOOLS & PLACING
Product Code No.
182
Wt. Lbs. per 100
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
T-50
Special Order Product Code No.
Wt. Lbs. 13.0
T-51
20-FORMING ACCESSORIES
T-52
30-ATLAS TECH PRODUCTS
GYRO SHEAR BAR Special Order Length
Product Code No.
30”
Wt. Lbs. per 100 175.0
GYRO TILT PLUSTM HEAVY DUTY INSERT Special Order Structural Panel Thickness
Product Code No.
Wt. Lbs. per 100
Packaging
8”
390.0
10
10”
445.0
10
12”
560.0
10
40-BAR SUPPORTS
Gyro Tilt Inserts are shipped assembled (ready-to-use). Each insert is sized 1/8” less than panel thickness above. Requires a minimum concrete compressive strength of 2,500 psi. When ordering, specify overall panel thickness including structural thickness and aggregate or form liner thickness.
T-53
Special Order Product Code No.
Wt. Lbs.
50-FLATWORK ACCESSORIES
GYRO TILT PLUSTM HEAVY DUTY HARDWARE
10-FORMING & SHORING
GYRO TILT PLUSTM HARDWARE
41.0
T-58
EXTRUDED PVC (POLYVINYL CHLORIDE) PLASTIC, .062” THICK Wt. Lbs. / Carton
20.27.12075
30.0
PRODUCTS
Shipped in 10 ft. lengths. Available in full cartons of 200 ft.
PLASTIC KEYWAY
T-59
Product Code No.
80- TOOLS & PLACING
EXTRUDED IN 10 FT. LENGTHS Special Order Wt. Lbs. 20.0
Available only in full cartons of 400 ft.
www.atlasform.com
70- FOUNDATION
Product Code No.
60-PRECAST & TILT-UP
DOUBLE CHAMFER STRIP
183
T-61
5” to 9” panel thickness
30-ATLAS TECH PRODUCTS 40-BAR SUPPORTS
Size
Product Code No.
1” x 6”
60.21.83060
1” x 7”
60.21.83007
1” x 9”
60.21.83009
1” x 12”
60.21.83012
QUICK RELEASE STRONGBACK BOLT FOR USE WITH T-61 STRONGBACK INSERTS WITH WING NUT AND FLAT WASHER Special Order Product Code No.
Wt. Lbs. 5.9 Ea.
T-63 T-63-S
ALUMINUM STRONGBACKS ALUMINUM SPLICE PLATE ASSEMBLY Special Order Description
T-66
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
T-62
PRODUCTS
70- FOUNDATION
QUICK RELEASE STRONGBACK INSERT Structural panel Thickness
T-68
80- TOOLS & PLACING
Contractor Committed.
FOR USE WITH T-62 STRONGBACK BOLTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
PRECAST & TILT-UP
T-75
184
Product Code No.
Wt. Lbs.
T-63 10’ Channel
118.0 Ea Set
T-63 15’ Channel
177.0 Ea Set
T-63 20’ Channel
236.0 Ea. Set
T-63 25’ Channel
295.0 Ea. Set
T-63-S Splice Assembly
28.0 Ea. Set
TILT BRACKET Type and Size
Product Code No.
Wt. Lbs. / Ea.
5” Bracket
60.25.66005
0.19
7” Bracket
60.25.66007
0.22
T-66 Tilt Bracket Shoe (single use)
60.25.66000
0.18
ACA-1000 CONSTRUCTION SPRAY ADHESIVE Product Code No.
Size Can
# Can/ Box
Wt. Box
60.25.66100
17 oz.
12
20.0
13 oz.
12
16.8
SPECIAL DRILL-IN LIFT PLATE Product Code No.
Wt. Lbs.
60.20.45001
33.0 Ea.
www.atlasform.com
Serving Concrete Customers Since 1980.
PRECAST & TILT-UP
Type
Product Code No.
Wt. Lbs. per 100
Packaging
8” 9”
Wire Based
60.21.40800
390.0
10
Wire Based
60.21.40900
10”
Wire Based
60.21.41000
495.0
10
12”
Wire Based
60.21.41200
560.0
10
20-FORMING ACCESSORIES
Structural Panel Thickness
10-FORMING & SHORING
T-81
GROUND RELEASE IITM HEAVY DUTY INSERT
T-83
GROUND RELEASE IITM HEAVY DUTY HARDWARE
30-ATLAS TECH PRODUCTS
Ground Release II Inserts are shipped assembled (ready-to-use). Each insert is sized 1/8” less than panel thickness above. Requires a minimum concrete compressive strength of 2,500 psi. When ordering, specify overall panel thickness including structural thickness and aggregate or form liner thickness.
Special Order Wt. Lbs. 23.2 Ea.
SUPERIOR LIFT TU INSERT Item Description
Product Code No.
Wt. Lbs./ Ea.
5”
T110- SUPERIOR LIFT 5”
60.21.10500
1.600
5-1/2”
T110- SUPERIOR LIFT 5-1/2”
60.21.10550
1.650
T110- SUPERIOR LIFT 6”
60.21.10600
1.700
T110- SUPERIOR LIFT 6-1/4”
60.21.10625
1.725
6-1/2”
T110- SUPERIOR LIFT 6-1/2”
60.21.10650
1.750
7”
T110- SUPERIOR LIFT 7”
60.21.10700
1.800
7-1/4”
T110- SUPERIOR LIFT 7-1/4”
60.21.10725
1.825
7-1/2”
T110- SUPERIOR LIFT 7-1/2”
60.21.10750
1.850
8”
T110- SUPERIOR LIFT 8”
60.21.10800
1.900
8-1/4”
T110- SUPERIOR LIFT 8-1/4”
60.21.10825
2.530
8-1/2”
T110- SUPERIOR LIFT 8-1/2”
60.21.10850 2.560 2.575
9-1/2”
T110- SUPERIOR LIFT 9-1/2”
60.21.10950
2.590
10”
T110- SUPERIOR LIFT 10”
60.21.11000
2.620
10-1/4”
T110- SUPERIOR LIFT 10-1/4”
60.21.11025
2.650
10-1/2”
T110- SUPERIOR LIFT 10-1/2”
60.21.11050
11”
T110- SUPERIOR LIFT 11”
60.21.11100
2.480
11-1/4”
T110- SUPERIOR LIFT 11-1/4”
60.21.11125
2.710
11-1/2”
T110- SUPERIOR LIFT 11-1/2”
60.21.11150
12”
T110- SUPERIOR LIFT 12”
60.21.11200
80- TOOLS & PLACING
60.21.10900 60.21.10925
PRODUCTS
T110- SUPERIOR LIFT 9” T110- SUPERIOR LIFT 9-1/4”
70- FOUNDATION
9” 9-1/4”
60-PRECAST & TILT-UP
6” 6-1/4”
www.atlasform.com
50-FLATWORK ACCESSORIES
Panel Thickness
T-110
40-BAR SUPPORTS
Product Code No.
2.240
185
10-FORMING & SHORING
FOUNDATION PRODUCTS
Contractor Committed.
VOID FORMS Sonovoid® Slab
Standard Sizes: width: 6”, 8”, 9”, 10”, 12”, 14”, 16”, 18” and 24”. height: 4”, 6”, 8”, 10” and 12”. Custom sizes available upon request. Standard Strength: Approximately 1600-3000* PSF ultimate capacity. Approved for maximum Beam/Wall height of 10 feet Extra Strength: Approximately 2000-4500* PSF ultimate capacity. Approved for maximum Beam/Wall height of 16 feet * Ultimate capacity depends on product size.
Standard Strength: Approximately 1000 PSF ultimate capacity. Approved for floors up to maximum 24” thick. Extra Strength: Approximately 1500 PSF ultimate capacity. Approved for floors up to maximum 36” thick. Super Strength: Approximately 2000 PSF ultimate capacity. Approved for floors up to maximum 48” thick.
structural concrete slab and underlying expansive soils. The SureVoid® material, lying under structural concrete construction, absorbs ground moisture and loses strength only after the concrete has set, creating space into which soil can expand without causing damage. SlabVoid® is designed to withstand the working load of the concrete construction process, then deteriorate with the absorption of moisture. Benefits of SlabVoid® Products •Lightweight and easy to install. •Available either factory assembled or knock-down (K.D.) for lower shipping and storage costs. •Easily cut to shorter lengths for proper fit. •Available in standard strengths and sizes, or can be custom manufactured to accommodate design and load specifications. •Can be used to displace concrete volume where reduction in weight or cost is a consideration.
PRODUCTS
WallVoid® System products provide temporary support systems for liquid concrete until the concrete sets and
80- TOOLS & PLACING
70- FOUNDATION
Standard Sizes: 4”, 6”, 8”, 10”, 12” thick. Custom sizes and strengths available upon request.
SlabVoid® is a corrugated paper product that helps eliminate severe damage by creating a space between the
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
SonoVoid® Beam
can support itself. They are ideal for concrete components that span across drilled piers, pads, intermittent footings, as well as other concrete work. The WallVoid® material, lying under structural concrete construction, absorbs ground moisture and loses strength only after the concrete has set, creating space into which soil can expand without causing damage. Benefits of WallVoid® Products •Lightweight and easy to install. •Available either factory assembled or knock-down (KD) for lower shipping and storage costs. •Easily cut to shorter lengths for proper fit. •Available in standard strengths and sizes, or can be custom manufactured to accommodate design and load specifications. •Placed end-to-end between drilled piers or spread footings. •End caps and seam pads available to prevent concrete from flowing into void.
186
www.atlasform.com
Serving Concrete Customers Since 1980.
FOUNDATION PRODUCTS
20-FORMING ACCESSORIES
The Boman Kemp Easy-Buck and Easy-Well Basement Window System is now ICC approved. The Boman Kemp system is the ONLY one in the industry to to be ICC approved and to receive an ESR number!
10-FORMING & SHORING
WINDOW SYSTEMS
30-ATLAS TECH PRODUCTS
Easy Well The Boman Kemp Easy-Well (or basement window well) is used to keep earth away from basement windows. It is designed to bolt directly to the Boman Kemp Easy-Buck or can be bolted to the wall during basement remodeling.
40-BAR SUPPORTS
Safety Grate The safety grate is made of rolled angle iron steel and steel safety bars. It is designed to keep people and pets out of the Easy-Well and hold the weight of standard foot traffic.
Escape Ladder 50-FLATWORK ACCESSORIES
The safety ladder is designed to assist people in an emergency escape or egress. The safety ladder hangs in the back of the Easy-Well and is required in area wells that are deeper than 44” per IRC 2003.
Windows
CUSTOM FABRICATION
PRODUCTS
70- FOUNDATION
80- TOOLS & PLACING
Atlas provides custom fabrication of steel beams and posts for residential basements as part of our product package for customers. Atlas offers standard sizes or can accommodate nearly any size for residential projects. Please contact your Atlas representative for further details.
www.atlasform.com
60-PRECAST & TILT-UP
The Boman Kemp double insulated vinyl window comes equipped with a sliding sash, screen, and is lockable from the inside. It is available in white and almond color and is also can be ordered in both Low E and tempered glass.
187
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
TOOLS & PLACING
Contractor Committed.
POWER SPRAYER REAL PUMPTM Power Spraying System Designed to spray: Form Oils & Other Release Agents : Concrete Sealers : Curing Compounds (Including White Wax Cures, High Viscosity & High Solids Products) : Stains Herbicides : Deck Sealers & Cleaners : Acids (special wand required) : Bleach Solutions : Fertilizers : Pesticides : Cleaners And Many Other Products • All Steel Construction for Durability • Large Rubber Feet for Stability • Comes Fully Assembled • Multiple Power Options Available Including • 115VAC includes standard 9’ power cord • 230VAC includes standard 9’ power cord • 12VDC includes standard 25’ power cord w/ battery clamps • Complete spray Control Kit Includes • 1-spray Control Gun with comfort grip handle and quick connect, open flow fittings • 1-18” Straight Brass Wand Section • 1-18” Curved Brass Wand Section • 1-Adjustable Brass Fan Nozzle • 100’ Safety Yellow 3/8” Chemical Resistant Hose with quick connect open flow fittings • Chemical Resistant Diaphragm and Seals in Pump and Reel • Utilizes a circuit breaker instead of fuses, protecting the operator and eliminating the need to search for fuses. • Pressure sensitive switch shuts off pump when you stop spraying, to prevent bursting hoses and product separation or damage. • This feature can be by-passed with our pressure activated re-circulator to continuously re-circulate and mix the product you are spraying. • Reduces Labor Costs • Portable, Easy to Use and Versatile • Reduces Material Cost • Easy to Clean • Reliable
Telescoping Spray Lance
PRODUCTS
Features • Quick connect fitting- will easily connect to the REAL Pump Power Spraying System • Heavy duty chemical and crush resistant hose available in two colors • High impact, fully adjustable plastic spray tip holder • Large, comfort grip spray control handle with viton seals • Composite fiberglass, telescoping pole- easily adjusts from 8 feet to 24 feet with application spray heights up to 40 feet when using cone nozzle. • Interchangeable, quick connect spray tips •1 gallon per minute quick connect 1100 fan tip •Adjustable, quick connect cone nozzle- adjusts to create a fine mist or an additional 18 foot spray pattern for an overall effective distance of over 40 feet. • Telescoping pole can also be converted for use as a scrapper handle
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
The telescoping adjustable height spray lance makes extended height and distance applications easy to reach up to 40 feet (12.2 meters) when using the cone nozzle provided. Drastically reducing your application times and improving the safety of your employees. At only 8 lbs. the adjustable lance is light weight and easy to maneuver. This application lance has been designed with a coil hose on the outside making it easier to clean or replace when needed. Using a coil type hose has eliminated the extra hose, normally lying at your feet, that is typically associated with telescoping spray lances.
188
www.atlasform.com
TOOLS & PLACING
Serving Concrete Customers Since 1980.
HAND PUMP SPRAYERS This open-head construction chemical sprayer is a top selling model and is unmatched for quality.
20-FORMING ACCESSORIES
• Use to spray-apply Atlas Tech form releases, curing compounds, sealers and bondbreakers. • 3.0 gallon solid brass pump barrel, shut-off, 18” extension, and 1/2 gallon per minute brass fan tip nozzle. • 4.5” open head tank for easy filling and cleaning. TRI-POXY coated steel makes tank corrosion resistant and easy to clean. • Lightweight for easy use. • Comes with a comfortable carrying strap. TANK
HOSE
PUMP
EXTENSION
STRAP
SHIP UNIT/ WGT
PRODUCT CODE NO.
3.0 G / 11.3L
TRI POXY
42” / 1.06m
12”/ 300 mm Brass
18” / 455 mm Brass
Yes
1-10.16 lbs 4.60 kg
80.20.10035
30-ATLAS TECH PRODUCTS
CAPACITY
10-FORMING & SHORING
CONSTRUCTION EQUIPMENT
SPRAY NOZZLES 40-BAR SUPPORTS
Atlas offers a wide array of spray nozzles to help contractors get the most out of each Atlas Tech Product. Most standard construction sprayers come with 0.5 gallon per minute fan spray tip, usually identified as a #8005 tip. This number identifies two characteristics of the tip: 1) #8005 - the degree angle of the tip (80 degrees) 2) #8005 - the flow rate (0.5 gallon/minute) Type Product Code No. 80.20.22102 80.22.22103
#8005 - cures, sealers, bonding agents
80.22.22105
#11010 - thick cures, bonding agents
80.22.22110
Fog Tip - form release agents
80.22.22000
ELEPHANT TRUNKS
Diameter
Product Code No.
Packaging
6”
80.12.50600
100’ roll
8”
80.12.50800
100’ roll
12”
80.12.51200
50’ roll
60-PRECAST & TILT-UP
Makes difficult wall pours easy. Made from durable polyvinyl chloride it is strong, lightweight, and ribbed for greater strength. It is easily affixed to concrete hoppers by the use of band steel and hand tools.
50-FLATWORK ACCESSORIES
#8002- bondbreakers #8003 - bondbreakers, low viscosity cures
PRODUCTS
Multiquip offers a diverse construction equipment product line including concrete placement, concrete finishing, soil compaction, dewatering pumps and more. Contact Atlas Construction Supply for further information. Vibratory Screeds • Concrete Pumps• Mortar Mixers Power Trowels • Rebar Cutters & Benders • Generators & More!
www.atlasform.com
189
80- TOOLS & PLACING
Camlever concrete buckets feature high strength, light weight tubular construction. Accessories sold separately include chutes, top ring extensions, bucket boots, boot extensions, etc. Please contact Atlas Construction Supply for further information.
70- FOUNDATION
MULTIQUIP CONSTRUCTION EQUIPMENT
CAMLEVER CONCRETE BUCKETS
Contractor Committed.
GROUT PUMP
ChemGrout CG-502 The ChemGrout Sprayer/Finisher Series is specially designed to offer the flexibility for both pump and spray applications. Its twin 45-gallon mixing tanks, pump and large holding hopper are all mounted on a single skid for quick, easy set-up and immediate operation. The low profile mix tanks enable greater ease when dispensing bags of dry material, reducing operator fatigue and increasing productivity. The tanks feature high-efficiency paddles that provide a rapid mixing cycle and ensure a smooth, consistent material mix. Each mix tank alternates feeding a centrally located holding hopper allowing for a continuous, non-stop process.
CG502 / 2C4 Skid Power
Electric Hydraulic
Max Output Pressure
8 gpm (30 lpm), 174 psi (12 bar)
Required
1 phase
Weight
1000 lbs
Size
82” L x 31” W x 55” H
Complete with wheels, and only 31 inches wide, the CG-502 offers the mobility required to move quickly and easily through standard size doorways. The rugged steel frame stands up to the toughest jobsite conditions. Operator controls are centrally located for efficient production. All components are easily accessible for operating, cleaning and maintenance. The ChemGrout 2C4 pumps allows for a steady and continuous flow of material, ideal for self-leveling underlayments, fine non-shrink grouts and most other spray and injection applications. A hinged clean-out port has been added to suction housing for quick access and clean up.
PRODUCTS
Atlas Rents the ChemGrout CG-502 pump for self-leveling underlayment and fine grouting needs. Call an Atlas Representative for details.
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
TOOLS & PLACING
190
www.atlasform.com
TOOLS & PLACING
Serving Concrete Customers Since 1980.
MOTORS Weight
HP
Volts
Amps
Max Head Size
Product Code No.
VME1500
12 lbs.
1.5
115 AC/DC
11
1-3/4”
80.15.11110
VME2500
15.5 lbs.
2.5
115 AC/DC
13
2-1/2”
80.15.11120
VME3000
19 lbs.
3.0
115 AC/DC
19
2-1/2”
80.15.11130
CORES Model
20-FORMING ACCESSORIES
Model
CASINGS Product Code No.
Model
Length
Product Code No.
3’ 5’
80.15.12010
3’
80.15.13010
80.15.12020
5’
80.15.13020
VBC7
7’
80.15.12030
VBCS7
7’
80.15.13030
VBC10
10’
VBC14
14’
80.15.12040
VBCS10
10’
80.15.13040
80.15.12050
VBCS14
14’
80.15.13050
VBC21
21’
80.15.12060
VBCS21
21’
80.15.13060
HEADS
30-ATLAS TECH PRODUCTS
Length
Radius of Effect
Product Code No.
Size
Model
Product Code No.
1-1/16” Steel
VBH1116
4-5”
80.15.14310
1-1/16”
VBRT1116
80.15.14110
1-5/16” Steel
VBH1516
5-7”
1-5/16”
VBRT1516
80.15.14120
1-9/16” Steel
VBH1916
10-13”
1-3/4” Steel
VBH134
15-17”
1-9/16”
VBRT1916
80.15.14130
80.15.14340
1-3/4”
VBRT134
80.15.14140
2-1/8” Steel
VBH218
17-21”
80.15.14350
2-1/8”
VBRT218
80.15.14150
2-1/2” Steel
VBH212
21-24”
80.15.14360
2-1/2”
VBRT212
80.15.14160
50-FLATWORK ACCESSORIES
Model
40-BAR SUPPORTS
INTERCHANGABLE RUBBER TIPS
Size
60-PRECAST & TILT-UP
INTERCHANGEABLE RUBBER TIPS
www.atlasform.com
2-1/8” Produces 1130 to 1455 lbs. of force 11,000 to 12,500 rpm vibrating frequencies. All-around size capable of handling stiff, low-slump concrete. 13” long.
2-1/2” Produces 1530 to 2200 lbs. of force 10,000 to 12,000 rpm vibrating frequencies. Ample force for stiffest, low-slump concrete. 13½” long.
80- TOOLS & PLACING
1-3/4” Produces 935 to 1130 lbs. of force 12,000 to 13,200 rpm vibrating frequencies. Good general purpose head size, 12” long.
PRODUCTS
1-5/16” Produces 440 to 535 lbs. of force 12,000 to 13,200 rpm vibrating frequencies. Excellent for thin prestress sections. 14” long.
1-9/16” Produces 730 to 880 lbs. of force 12,000 to 13,200 rpm vibrating frequencies. For thin wall sections or general purpose vibrating. 12” long.
70- FOUNDATION
1-1/16” Produces 150 to 180 lbs. of force 12,000 to 13,200 rpm vibrating frequencies. Ideal for thinnest prestress sections. 11” long.
10-FORMING & SHORING
CONCRETE VIBRATORS
191
LIGHTWEIGHT MAGNESIUM SCREEDS
30-ATLAS TECH PRODUCTS
Description
Product Code No.
Screed Mag 6’
80.40.11060
Screed Mag 8’ X 1-1/2” X 3-1/2”
80.40.11080
Screed Mag 10’ X 1-1/2” X 3-1/2”
80.40.11100
Screed Mag 12’ X 1-1/2” X 3-1/2”
80.40.11120
Screed Mag 14’ X 1-1/2” X 3-1/2”
80.40.11140
Screed Mag 16’ X 1-1/2” X 3-1/2”
80.40.11160
Screed Mag 20’
80.40.11200
• Other sizes available upon request
ROUND FRESNO Description
Product Code No.
5” x 36”
80.40.27130
5” x 48”
80.40.27145
40-BAR SUPPORTS
• Other sizes available upon request
50-FLATWORK ACCESSORIES
SQUARE FRESNO Description
Product Code No.
5” x 24”
80.40.27115
5” x 36”
80.40.27125
5” x 48”
80.40.27150
• Other sizes available upon request
60-PRECAST & TILT-UP
POOL TROWELS Description
Product Code No.
5” x 14”
80.40.42430
5” x 20”
80.40.41753
• Other sizes available upon request
PRODUCTS
CONCRETE TROWELS Description
Product Code No.
12” x 4”
80.40.41330
16” x 4”
80.40.41530
18” x 4”
80.40.41630
• Other sizes available upon request
HAND AND WALKING EDGERS
80- TOOLS & PLACING
70- FOUNDATION
Contractor Committed.
CONCRETE TOOLS
20-FORMING ACCESSORIES
10-FORMING & SHORING
TOOLS & PLACING
Various sizes and radii available.
192
www.atlasform.com
TOOLS & PLACING
Serving Concrete Customers Since 1980.
CONCRETE TAMPERS Product Code No.
36”
80.40.13010
48”
80.40.13020
20-FORMING ACCESSORIES
Description
DIRT/STAMP TAMPERS Description
Product Code No. 35.50.95010
12” x12”
35.50.95020
16” x 16”
35.50.95030
30-ATLAS TECH PRODUCTS
10” x 10”
FLOOR SCRAPERS Description
10-FORMING & SHORING
CONCRETE TOOLS
Product Code No. 80.48.31300
5” x 18”
80.48.31400
5” x 22”
80.48.31500
40-BAR SUPPORTS
5” x 14”
OVERLAY SQUEEGEES Handle
Product Code No. 80.48.11024
24” Neoprene
6’ Standard
30” Serated Edge
6’ Standard
80.48.11030
36” Neoprene
6’ Standard
80.48.11036
50-FLATWORK ACCESSORIES
Description
NAILS Description
60-PRECAST & TILT-UP
TAPE AND NAILS Product Code No.
80.50.12120
16 Duplex
80.50.12130
6 Common
80.50.11110
PRODUCTS
80.50.12110
8 Duplex
TAPE Product Code No.
Duct Tape
80.75.12100
Duct Tape Red
80.7512120
Packaging Tape
80.75.13200
80- TOOLS & PLACING
Description
• Other types available varies by location
www.atlasform.com
70- FOUNDATION
6 Duplex
193
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Contractor Committed.
INDEX BY PRODUCT NAME Item
Page No.
A-100 Bracket.....................................................25 A-Clamp..............................................................21 A-Deck...........................................................11-14 ACS Wallform................................................26-27 ADA Detectable Warning Panels......................159 Abrasive Blades & Blocks.....................................2 Adhesive Spray.................................................184 Adjustable Coil Bolt .........................................61 Adjustable Kicker..............................................143 Adjustable Weld Angle Bracket ........................71 Aggregates............................................................2 Alisply..................................................................28 AL-SPEED® Shoring Frame..........................8 - 10 Aluminum Beam......................................8 - 10, 21 Aluminum Grits (non-slip).................................155 Aluminum Strongbacks.......................................21 Aluminum Wall Forms.............................20-25, 30 Anchor Bolts.......................................................67 Anchor Bolt Sleeves .........................................67 Anchoring Epoxy........................................105,126 Angle Bracket................................................21,23 Area Wells........................................................187 Arcis Detectable Warning Panels.....................159 Atlas Tech Products.....................................86-125 Backer Rod...........................................................2 Bag Ties............................................................134 Bar Chairs/ Supports.................................130-133 Bar, Stripping.......................................................49 Barlock Couplers...............................................137 Barrier Dowel Aligner .......................................139 Barrier Fencing.....................................................2 Base Tie ..........................................................50 Basket Clip........................................................140 Basket, Dowel...................................................138 Batter Washer................................................65,71 Beam Bolster.....................................................131 Beam Clip ..........................................................85 Beam Form Systems.....................................18-19 Bearing Pads........................................................2 Bearing Plate......................................................45 Bentonite Waterstop.........................................158 Better Bar............................................................49 Blankets, Curing................................................154 Blind Side Walls.............................................30,44 Bolsters.....................................................130-131 Bolts...............................................................67,71 Bolt Clamp..........................................................67 Bondbreakers................................................96-97 Bonding Agents.........................................100-107 Bottom Jacks........................................................9 Box Culvert Form System...................................31 Box Voids..........................................................186 Brace Anchor....................................................177 Brace Anchor for Fill .......................................176 Braces, Tilt-Up..................................................179 Breakback Wrench .........................................49 Bridge Deck Repair Products....................108-110 Bridge Overhang Bracket..............................38-39 Bulkhead Bracket...........................................21,23 Bulkhead Form...................................................44 Bullfloats...........................................................192 Burlap...............................................................154 Burlene.............................................................154 Cap Plug ..........................................................78 Capitol Forms.....................................................33
194
Item
Page No.
Castellated Steel Beams....................................17 Catwalk Bracket.......................................21, 38-39 Cement...................................................................2 Cementitious Repair Products....................113-123 Ceramar Expansion Joint..................................145 Chamfer Strips....................................................41 Chemical and Cement Products .................86-129 Clamp Wallform System.................................26-28 Cleaning Agent (for concrete)..............................98 Closed Coupler....................................................73 Coil Anchor/Tang...............................................178 Coil Bolts ...........................................................60 Coil Inserts.....................................................58-62 Coil Loop Insert Straight.................................61-62 Coil Nut Washer...................................................63 Coil Nuts ...........................................................59 Coil Rod ...........................................................59 Coil Ties ...........................................................57 Colored Concrete Systems........................128-129 Color Hardener...................................124-125, 128 Column Clamps..............................................32,35 Column Forms................................................32-35 Column Mounted Table Forms............................17 Column Mounted Jacks.......................................38 Composite Form Panel........................................27 Concrete Buckets..............................................189 Concrete Cleaner.................................................98 Concrete Plugs....................................................53 Concrete Pumps................................................189 Concrete Restoration.................................102-123 Concrete Saws......................................................2 Concrete Stamps............................42-43, 128-129 Concrete Toppings.......................116-117, 128-129 Cone Removal Wrench.......................................50 Construction Spray Adhesive............................184 Corewall Slotted Inserts.............................160-161 Cork Expansion Joint ........................................145 Corrosion Inhibitors.......................................2, 104 Corrugated Wall Tie ..........................................77 Couplers.............................................134-135, 137 Crack Repair...............................................102-108 Crossbraces.....................................................9-10 Curb Forms........................................................143 Cure Lap............................................................154 Cure & Seal Compounds................................89-94 Curing Blankets.................................................154 Curing Compounds................................89-93, 127 Cushion-Lock Reglet...........................................84 Cut Washer........................................................148
DBR Coupler......................................................134 DBR Setting Splice Bars....................................134 Deck Forms......................................................8-19 Decorative Concrete Systems..................128-129 Delta Tie Sandwich Panel..................................160 Diamond Blades....................................................2 Dobies................................................................133 DOT Curing Compounds........................90-91, 127 DOT Patch..........................................110, 115-116 Double Chamfer Strip........................................183 Double Flared Coil Loop Insert .........................62 Double Flared Criss Cross Coil Loop Insert........64 Double Flared Loop Insert...................................79 Double Pickup Inserts........................................175 Double Swivel Lifting Plate................................180 Double Tee Specialty Anchor.............................173
www.atlasform.com
Item
Page No.
Dovetail Anchor Slot ..........................................77 Dovetail Anchors..................................................77 Dowel Bar Splicer(DB-SAE)..............................135 Dowel Baskets...................................................138 Dowel Caps................................................139-140 Dowel-In (D-l).....................................................135 Dowels.........................................................139,155 D/R Shebolt..........................................................72 D/R Taper Tie.......................................................69 D/R Threadbar......................................................59 Drainage Channels.....................................150-152 Drip Strips............................................................41 Drophead Shoring System..............................11-14 DSI Rod...............................................................45 Drop-In Anchors................................................2,64 Ductile Embed (SAE) ..........................................81 Dustproofer / Sealer / Hardener...........................95 Dynamic Leg Shoring System..............................15 Edge Form.........................................................143 Edge Form Brace...............................................143 Edge Lifting Plate...............................................180 Edge Pick-Up Insert, Double..............................176 Edge Pickup Insert, Single.................................176 Edgers (hand)....................................................192 Elephant Trunks.................................................189 End Pick-Up Insert, Double...............................178 End PIck-Up Insert, Single................................178 Epoxies...............................................102-109, 126 Epoxy Coatings..................................................127 Epoxy Grout.......................................................126 Epoxy Injection...................................102-105, 126 Epoxy Mortar.....................................................116 Epoxy Retention Ring........................................140 Erection Anchors...............................................171 Erosion Control Products.......................................2 Evaporation Retarder...........................................91 Expanded Coil Insert ..........................................81 Expanded Metal..................................................44 Expanded Polystyrene.......................................149 Expansion Joint Fillers.......................................145 Eye Anchors.......................................................162 Eye Bolt ............................................................79 Eye Nut ............................................................79 E-Z Chair............................................................132 Fasteners...............................................................2 Fencing, Silt & Barrier............................................2 Ferrule Instead of a Coil......................................84 Ferrule Loop Insert (Straight)..............................82 Fiberglass Column Forms...................................33 Fiberglass Rod....................................................74 Fiber Expansion Joint........................................145 Fibre Forms.........................................................34 Finish Machines.................................................189 Finishing Aid........................................................91 Fitting-Up Bolts and Nuts.....................................71 Flared Thin Slab Insert (Coil) .........................82 Flared Thin Slab Insert (Ferrule) .........................82 Flat Foot Anchors..............................................172 Flat Tie ................................................................48 Flat Washer....................................................45, 58 Fleet Lift System.........................................170-174 Flex Form System................................................29 Floats.................................................................192 Floor Coatings...................................................127 Floor Cover........................................................154 Floor Hardeners..................................124-125, 127
Serving Concrete Customers Since 1980.
Item
Page No.
Item
Page No.
www.atlasform.com
195
80- TOOLS & PLACING
Panel Pads........................................................167 Paper Tubing.....................................................148 Parking Structure Form Systems...................18-19 Patching Products......................................113-126 Pencil Rod...........................................................69 Pipe Brace.........................................................179 Pipe Turning Device..........................................167 Plastic Cap for Expansion Joint........................146 Plastic Cones for Coil Ties..................................63
PRODUCTS
Jahn ”A” Bracket.................................................55 Jahn ”C” Bracket.................................................55 Jahn Cornerlock..................................................55 Jahn Eccentric.....................................................56 Jahn Rivet...........................................................56
Omni Wedge.......................................................47 On-Site Pipe Bace.............................................179 One-Sided Wall Forms...................................30,44 OSHA Regulations.............................................4-5 Overhang Bracket..........................................38-39 Overlays (Decorative)................................128-129 Overlays (Structural)....................109-110, 114-117
Radius Formers..................................................41 Radius Wall Forms........................................28-29 Rail Fastener Embed (RT-SAE).........................81 Rebar................................................................141 Rebar Clip and Form Spreader...........................71 Rebar Couplers........................................135, 137 Rebar Cutters & Benders.................................189 Rebar Guards, Plastic......................................140 Rebar Supports.........................................130-133 Recess Members..............................................174 Recess Plugs (Fleet Lift)..................................174 Recess Plugs (Swift Lift)...........................163-164 Reinforcing Bar for Swift Lift Anchors...............164 Removable Plastic Cap Strips..........................146 Repair Mortars...........................................113-122 Reshore Products...................................36, 38, 56 Retarders............................................................99 Ring Clutches...................................................170 Riser Frames....................................................148 Rock Anchor (Coil Thread).................................64 Rocket/Kohler Ferrule Insert...............................80 Rod Clamp..........................................................69 Rod Clamp (Superior).........................................70 Rollerback Carriage............................................25 Round Column Forms...................................33-34 Round Stakes...................................................144
70- FOUNDATION
Injection Resins.................................102-105, 126 Insert Locator Plug............................................180 InsertionTool........................................................54 Inside Tie Rod.....................................................66 Integral Color.............................................128-129 Intersectional Chairs..................................130-132 Inverted Brace Achor........................................177
Nails..................................................................193 Non-Shrink Grouts......................................111-112 Non-Slip Finish..................................................155 Nut Washer (Acme).............................................68
Quantum-Cure....................................................89 Quick Release Strongback Bolt........................184 Quick Release Strongback Insert.....................184
60-PRECAST & TILT-UP
Handle Coil Nut...................................................64 Handset Deck Forms.......................................8-13 Hardener (Dry-Shake).......................124-125, 127 Hardener (Liquid).........................................95,127 HDO Plywood......................................................40 He-Bolt................................................................73 Header Forms...................................................143 Header Form Support...............................143, 147 Heavy Coil Hex Nuts...........................................63 Hex Coupling Nut................................................68 High Chairs................................................130-132 Holding Plate.....................................................174 Holding Rod......................................................174 HookTie.........................................................44, 47
Magna Jaw..........................................................73 Median Barrier Forms...........................................2 Mesh Supports...........................................130-133 Methacrylate......................................................110 Mike Bracket........................................................44 Mixers........................................................189-190 Modular Form Systems............................26-28, 31 Moisture Barrier..........................................153-154 Moisture Retaining Cover..................................154
50-FLATWORK ACCESSORIES
“L” Anchor..........................................................171 “L” Leg Inserts.....................................................80 Laminated Veneer Lumber (LVL)........................40 Lead Plugs..........................................................45 Lift Plate (Drilled)...............................................184 Lifting Anchors...................................................162 Lifting Angle.......................................................177 Lifting Eyes........................................................161 Lifting Lug...........................................................21 Lined Tube.....................................................33-34 Liquid Bonding Agents...............................100-101 Load Key...........................................................147 Load Transfer Joint System..............................155 Loop Ferrule Insert..............................................78 Loop Strongback Tie...........................................55 LoopTies..............................................................51 LVL Beams.................................................8-13, 40
40-BAR SUPPORTS
Ganged Aluminum Wall Forms...........20-25, 29-30 Garage Beam Forms.....................................18-19 Generators........................................................189 Geosynthetics/Geotextiles....................................2 Graffiti Remover....................................................2 Grates for Trench Drain.............................150-152 Ground Release II Insert...................................181 Ground Release II Insert (HD)..........................185 Ground Release II Lifting Hardware..................181 Ground Release II Lifting Hardware (HD).........185 Ground Release II Patch Caps.........................182 Ground Release II Spreader Beam...................182 Grouts.................................................111-112, 127 Grout Pumps..............................................118,190 Grout Retention Ring........................................140 Guard Rail Post...................................................37 Gyro Tilt Plus Edge Lift Insert............................182 Gyro Tilt Plus Face Lift Insert............................182 Gyro Tilt Plus Insert (HD).................................183 Gyro Tilt Plus Hardware....................................183 Gyro Tilt Plus Hardware (HD)...........................183
Keyway...............................................................183 Korolath Bearing Strips.....................................168 Korolath Core Plugs..........................................169 Korolath Heavy Duty Shimpaks........................168 Korolath Horseshoe Spacer Strips....................169 Korolath Shim Strips.........................................168
Plastic Cones for Snap Ties...............................46 Plastic Cones for Taper Ties...............................45 Plastic Cone Removal Wrench...........................61 Plastic Keyway..................................................183 Plastic Plug.........................................................85 Plastic Rebar Guards.......................................140 Plastic Setback Plug...........................................65 Plastic Setting Bolt............................................160 Plastic Sleeves (for ties).....................................45 Plastic Zip Strip Joint Former............................146 Plate Anchor.....................................................172 Plate Washer..................................................45,58 Plugs, Tie Hole..............................................45,53 PlyLag................................................................63 Plywood Form Panels.........................................40 Polydrain...................................................150-152 Polyester Concrete Overlays............................110 Polyethylene Film.............................................154 Polymer Concrete.......................109-110, 114,116 Polystyrene.......................................................149 Polyureas..........................................................127 Polyurethane Sealants......................................107 Portland Cement...................................................2 Post Shore..........................................................36 Post Shore Clamp (4x4).....................................56 Post-Tensioned Slab Products.........................130 Power Sprayers................................................188 Power Trowels..................................................189 Precast Accessories..................................160-174 Precast Trench Drain................................150-152 Protective Rebar Covers..................................140 Pumps................................................118,189-190 PVC Sheeting.......................................................2 PVC Sleeve........................................................45 PVC Waterstop..........................................156-157
30-ATLAS TECH PRODUCTS
Jahn Scaffold Jack..............................................56 Jahn Tie Extender................................................55 Joint Caps.........................................................146 Joint Forming System........................................155 Joint Repair Products.................106-110, 126-127 Joint Sealants............................106-107, 126-127 Joists (Flying Deck Form)...................................16 Jumbo Shore.......................................................36 Jump Form Systems......................................24-25 Jump Shoe..........................................................25
Page No.
20-FORMING ACCESSORIES
Floor Scrapers...................................................193 Floor Underlayments..........................118-119, 127 Flying Deck Forms...................................14, 16-17 Foam (for use with Recess Member)................174 Footing Ties..........................................................2 Form Board.......................................................143 Form Clamp........................................................70 Form Panels..................................................31, 40 Form Patch and Magnetic Setting Tool...............85 Form Release Agents....................................87-88 Form Spacers...................................................132 Form Spreaders..................................................49 Form Systems................................................8 - 35 Form Tie System......................................21, 23,45 Formliners......................................................42-43 Frame Connector...................................................9 Fresnos.............................................................192
Item
10-FORMING & SHORING
INDEX BY PRODUCT NAME
PRODUCTS
80- TOOLS & PLACING
70- FOUNDATION
60-PRECAST & TILT-UP
50-FLATWORK ACCESSORIES
40-BAR SUPPORTS
30-ATLAS TECH PRODUCTS
20-FORMING ACCESSORIES
10-FORMING & SHORING
Contractor Committed.
INDEX BY PRODUCT NAME Item
Page No.
Safety Notes......................................................6-7 Safety Rail Post..................................................37 Sand.....................................................................2 Sand Plate........................................................132 Sandwich Panel Erection Anchor......................171 Scaffold Bracket (Jack).................................38, 56 Scissor Clamps...................................................35 Screed Bracket..................................................146 Screed Key........................................................147 Screed Pad.......................................................146 Screed Post......................................................146 Screeds (Magnesium).......................................192 Screeds (Vibrating)...........................................189 Screw Anchor......................................................75 Screw Anchor Bolt Setting Template...................75 Screw Anchor Bolts .........................................75 Screw Anchor Eye Bolts.....................................75 Screw Anchor Setting Bolt..................................75 Screwjacks.......................................................8 - 9 Sealants, Urethane............................................107 Sealers...................................................92-95, 127 Self-Leveling Topping.................................116-117 Self-Leveling Underlayment.......................118,127 Set-EEZ Lubricant.............................................178 Shake-On Floor Hardeners................124-125, 127 She Bolt ......................................................45,72 She Bolt (Outside Stud Rod)...............................68 Shear Bar..........................................................173 Shear Bar For Swift Lift Anchors ......................164 Shelf Angle Insert................................................76 Shim Packs.......................................................168 Shoring Systems..............................................8-19 Shotcrete..............................................................2 Shoulder Eye Bolt .........................................79 Silane / Siloxane Sealers..................................127 Silica Sand............................................................2 Single Flared Coil Loop Insert.............................62 Single Pickup Insert..........................................175 SL Anchors........................................................162 SL Attachment Nut............................................167 SL Attachment Stud with Wing Nuts.................165 SL Countersunk Screw.....................................165 SL Eye Anchor..................................................162 SL Lifting Eyes..................................................161 SL Plus Coil Wing-Nut......................................166 SL Recess Plugs ..............................................163 SL Rubber Ring For Steel Recess Plug............164 SL Safety Pin with Washer................................166 SL Setting Plate with Countersunk Screw.........165 SL Steel Recess Plug.......................................164 SL Stud.............................................................165 SL Tapped Plate................................................166 SL Throw-Away Recess Plug...........................163 SL Universal Lifting Eyes..................................161 SL Wing Nut......................................................166 Slab Bolsters..............................................130-133 Slab Grabbers.....................................................37 Smooth Dowels.................................................139 Snap Tie Shank Wrench.....................................49 Snap Ties............................................................46 Snap Tie Wedges................................................47 Soil Stabilization Products.....................................2 Sonotube.............................................................34 Space Wheels...................................................132
196
Item
Page No.
Spandrel Hook Tie..............................................47 Spandrel Plate Tie..............................................47 Spandrel Point Tie..............................................47 Special Anchor......................................................2 Special Drill-In Lift Plate....................................184 Speed Dowels...................................................155 Speed Step.........................................................56 Speedy Bracket...................................................54 Splice Bars.................................................134-135 Spray Tips.........................................................189 Sprayers....................................................188-189 Spreader Beam.................................................182 Spreader Cleats..................................................49 Squeegees........................................................193 Stainless Steel Snap Tie....................................50 Stains, Color..............................................128-129 Stake for Dowel Baskets..................................139 Stake tor Screed Key and Load Key.................147 Stakes...............................................................144 Stamps, Textured Mats.....................................128 Star Inserts.......................................................169 Stayform..............................................................44 Steel Stakes......................................................144 Steel-Ply..............................................................31 Stencils......................................................128-129 Stiffback Bracket.................................................54 StrapTie ...........................................................48 Stripping Bar.......................................................49 Strongback Tie....................................................50 Stud Rail...........................................................136 Styrofoam..........................................................149 Supertie Fiberglass Rod.....................................74 Supertie Gripper..................................................74 Supertie Spreader Clip........................................74 Supertie Waler Wedge........................................74 Supertie Waterstop.............................................74 Supertie Wedge..................................................74 Sure-Guard Rebar Protector.............................140 Sure-Lock Bracket..............................................53 Sure-Lock Strongback Clamp............................54 Sure-LockTie.......................................................53 Sure Plug ...........................................................54 Sure Plug Insertion Tool......................................54 Sure-Snap Wrench Head Snap Ties...................46 Surface Retarders...............................................99 Swift Lift Plus Holding Stud with Wing Nut........165 Swift Lift Plus Plates .......................................166 Swift Lift Plus Recess Plug...............................163 Swift Lift System........................................161-167 Swivel Lifting Plate...................................178, 180 “T” Anchor.........................................................172 Tampers............................................................193 Tang, Coil Anchor..............................................178 Tape..................................................................193 Taper Ties................................................45, 68-69 Tension Bar.......................................................173 Thin Slab Ferrule Insert......................................78 Threaded Bar.................................................45,59 Threaded Inserts................................................76 Threaded Plastic Plug........................................84 Threaded Pullout Tie..........................................47 Threaded Steel Setting Plugs............................83 Tie Key...............................................................48
www.atlasform.com
Item
Page No.
Tie Plate.......................................................21, 23 Tie Wire............................................................133 Tightening Wrench..............................................70 Tilt Bracket (Edge Form) ..................................184 Tilt-Up Accessories....................................175-185 Tilt-Up Braces....................................................179 Tip To Tip Tie.......................................................47 Toggle Pins............................................................9 Top Jacks..............................................................9 Toggle Coil Ties...................................................64 Tower Chairs.....................................................132 Trench Drains.............................................150-152 Triple Flared Coil Loop........................................65 Trowels..............................................................192 Trowels, Power..................................................189 Truss & Joist Tables.............................................16 Truncated Domes..............................................159 Tube Forms....................................................33-34 Turnbuckle Form Aligner......................................49 Two-Hole Anchor................................................171 Type L Inserts......................................................83 Type B-4 Cushion-Lock Reglet............................84 Underlayments............................................118,127 Urethane Coatings.............................................127 Utility Anchors...................................................167 Vapor Retarders.........................................153-154 Vibrators............................................................191 Vibratory Screeds..............................................189 Visqueen....................................................153-154 Void Forms.................................................149,186 Wale Bolt Assembly.............................................61 Wale Holder.........................................................62 Waler Jack...........................................................38 Waler Tie.............................................................52 Wall Clamps.......................................21, 23, 26-27 Wall Forms.....................................................20-31 Wall Plug.............................................................78 Washer Plates.....................................................58 Water Plug.........................................................122 Water Repellents..............................................127 Waterproof Coating...........................................123 Waterstops.................................................156-158 Wedge (for use with Recess Member)..............174 Wedge Anchors.....................................................2 Wedge Bolt..........................................................52 Welded Wire Fabric...........................................142 Welding Coil Tie..................................................58 Wheels (Plastic Form Spacers).........................132 Window Systems...............................................187 Wing Nut (Coil Thread)........................................65 Wing Nut (Threaded Bar)..............................45, 59 Wire Mesh.........................................................142 Wood Chamfer.....................................................41 Wrench Head Snap Tie Socket...........................50 X FlatTie..............................................................48 YokeBracket........................................................23 Z Tie Holder.........................................................52 Zip Strip Joint Former........................................146
View more...
Comments
