Casa System C3200 CMTS Manual

CASA CMTS

CASA CMTS

VERSION: SEPTEMBER 23, 2013 ........................................................................................................................ 1 (FOR SOFTWARE RELEASES 5.2, 5.4.19, 5.4.21, 6.0.3, 6.1.1, 6.1.2, 6.1.3, AND 1G.1)........................................... 1 TABLE OF CONTENTS ............................................................................................................................. 3 PREFACE.............................................................................................................................................. 29 PURPOSE OF THE GUIDE .................................................................................................................................. 29 AUDIENCE .................................................................................................................................................... 29 REVISION INFORMATION ................................................................................................................................. 29 CONTENTS ................................................................................................................................................... 35 NOTATION CONVENTIONS ............................................................................................................................... 35 1 CASA CMTS CONFIGURATION OVERVIEW.......................................................................................... 36 SLOT AND PORT NUMBERING ........................................................................................................................... 36 C2200 slot and port numbering ............................................................................................................ 36 C3200 slot and port numbering ............................................................................................................ 38 C10200, C10G, and C100G slot and port numbering ............................................................................ 38 C10G AND C100G REDUNDANCY OPERATIONS................................................................................................... 39 Slot information and cabling on the network side ................................................................................ 39 Slot information on the RF I/O side....................................................................................................... 39 High availability (HA) redundancy commands...................................................................................... 40 Fan, power, and temperature status on the C10G ............................................................................... 44 C10G 8-channel QAM frequency configurations .................................................................................. 45 C10G router redundancy....................................................................................................................... 47 C1G/C1N FEATURES AND CONFIGURATION DIFFERENCES WITH LARGER PLATFORMS .................................................. 47 COMPLETING PRE-CONFIGURATION ................................................................................................................... 47 USING THE COMMAND LINE INTERFACE .............................................................................................................. 48 STARTING THE SYSTEM CONFIGURATION ............................................................................................................. 48 Connecting the console ......................................................................................................................... 49 Resetting the console............................................................................................................................ 49 Starting the system ............................................................................................................................... 49 Viewing the loaded software version ................................................................................................... 50 Viewing the system hardware configuration ........................................................................................ 50 Viewing the system running configuration ........................................................................................... 50

CASA CMTS Entering and exiting configuration mode ............................................................................................. 51 Configuring CMTS device contact and location strings......................................................................... 51 Setting security access to the system console ...................................................................................... 51 Setting the console timout .................................................................................................................... 52 Saving the current configuration .......................................................................................................... 53 Resetting the IP address ....................................................................................................................... 54 Restoring factory defaults .................................................................................................................... 54 SAMPLE CONFIGURATION FILES ......................................................................................................................... 55 Basic configuration ............................................................................................................................... 55 General configuration ........................................................................................................................... 57 2 CONFIGURING AND MANAGING THE CMTS FROM THE CLI ................................................................ 60 MANAGING THE SYSTEM ................................................................................................................................. 61 Entering privileged mode ...................................................................................................................... 62 Exiting privileged mode ........................................................................................................................ 62 Changing the privileged mode password ............................................................................................. 63 Resetting the privileged mode password to the default setting ........................................................... 63 Encrypting passwords ........................................................................................................................... 63 Changing the prompt for privileged mode ........................................................................................... 64 Setting up a command alias ................................................................................................................. 64 Showing the configured command alias............................................................................................... 65 MANAGING CONFIGURATIONS AND FILES............................................................................................................ 65 Saving a running configuration to the startup configuration ............................................................... 65 Copying the startup configuration to a file........................................................................................... 66 Restoring a startup configuration from a file in NVRAM ...................................................................... 66 Restoring the startup configuration to the running configuration ....................................................... 66 Copying the running configuration to an external location .................................................................. 67 Copying files over FTP/TFTP.................................................................................................................. 68 Copying files from fdsk2 to destinations over FTP/TFTP ....................................................................... 70 Specifying an MD5 checksum file ......................................................................................................... 71 Displaying fdsk2 directory contents ...................................................................................................... 71 Displaying the running configuration ................................................................................................... 71 Displaying the system startup configuration ........................................................................................ 72 Displaying configuration settings within the current context............................................................... 72 MANAGING NVRAM FILES ............................................................................................................................. 72 Listing files in the directory ................................................................................................................... 72

CASA CMTS Removing a file from the directory ....................................................................................................... 73 Copying a file to a remote host............................................................................................................. 73 UPDATING CASA CMTS SOFTWARE .................................................................................................................. 74 USER MANAGEMENT AND SECURITY CONTROL ..................................................................................................... 74 Assigning commands to user levels ...................................................................................................... 75 SSH support (Release 5.4 and later)...................................................................................................... 76 Enabling and disabling SSH................................................................................................................... 78 Adding Telnet and SSH users ................................................................................................................ 78 Displaying Telnet and SSH users ........................................................................................................... 79 Changing Telnet and SSH user passwords ............................................................................................ 80 Removing Telnet or SSH users .............................................................................................................. 80 Removing a logged-in user ................................................................................................................... 81 Configuring and displaying the Telnet port .......................................................................................... 81 Setting the maximum number of concurrent Telnet session ................................................................ 82 Configuring Telnet and SSH timeout periods ........................................................................................ 82 Rebooting the system ........................................................................................................................... 82 Enabling  a  “save  configuration”  reminder  at  reboot............................................................................ 84 Rebooting a downstream/upstream module ....................................................................................... 85 Displaying the system boot device........................................................................................................ 85 Displaying the system hardware version .............................................................................................. 85 Displaying the system software version ............................................................................................... 86 Setting and displaying the system clock ............................................................................................... 86 Setting and displaying the time zone.................................................................................................... 87 Synchronizing the system clock with an NTP server ............................................................................. 88 Displaying NTP status ........................................................................................................................... 89 Configuring system rate limiting (Rel. 6.0 and later) ............................................................................ 89 Configuring an NTP loopback interface ................................................................................................ 90 Adding and removing IPv4 network route entries ................................................................................ 90 Adding and removing IPv4 host table entries ....................................................................................... 91 Adding and removing IPv6 network route entries ................................................................................ 91 Displaying the IPv4 and IPv6 routing tables ......................................................................................... 92 Displaying IP interface status ............................................................................................................... 92 Displaying alarm states ........................................................................................................................ 93 Displaying system logs .......................................................................................................................... 94 Configuring a log message source IP address....................................................................................... 94

CASA CMTS Configuring lawful intercept ................................................................................................................. 94 Displaying Rapid Spanning Tree Protocol status .................................................................................. 95 Displaying ARP entries .......................................................................................................................... 96 Configuring the ARP request interval ................................................................................................... 97 Configuring ARP packet filtering........................................................................................................... 97 Clearing an entry in the ARP cache ....................................................................................................... 98 Displaying the ARP request interval ..................................................................................................... 98 Enabling and disabling the ARP timeout reset ..................................................................................... 99 Displaying IPv6 information.................................................................................................................. 99 Displaying the ARP timeout reset configuration................................................................................. 100 Displaying CPU usage ......................................................................................................................... 100 Displaying memory usage................................................................................................................... 103 Viewing module statistics ................................................................................................................... 104 Monitoring line card status ................................................................................................................ 107 Monitoring Gigabit Ethernet interfaces.............................................................................................. 107 Clearing interface statistics ................................................................................................................ 108 Displaying the current monitor settings (Rel. 6.0 and later)............................................................... 108 Enabling auto-reboot mode (5.2) ....................................................................................................... 108 Using the ping and ping6 commands ................................................................................................. 109 Testing connectivity with extended ping ............................................................................................ 110 Using the traceroute commands ........................................................................................................ 110 Configuring ICMP packet filtering....................................................................................................... 113 Configuring DHCP packet filtering ...................................................................................................... 114 Displaying all filtering settings in the running configuration ............................................................. 114 Setting channel utilization intervals ................................................................................................... 115 Displaying channel utilization ............................................................................................................. 115 Displaying upstream channel utilization............................................................................................. 117 Displaying downstream channel utilization........................................................................................ 118 Configuring the system monitor (Release 5.4 and later) .................................................................... 119 CONFIGURING THE MANAGEMENT PORT........................................................................................................... 120 Setting the Fast Ethernet port as the management port.................................................................... 120 Obtaining the IP address of the Fast Ethernet port from the DHCP server ......................................... 121 Configuring an IP access group on eth0 (C3200 and C10200 only) .................................................... 121 CONFIGURING GIGABIT ETHERNET (GIGE) PORTS............................................................................................... 122 Enabling/disabling auto-negotiation mode on a Gigabit Ethernet port ............................................. 123

CASA CMTS Assigning or removing a Gigabit Ethernet port IP address ................................................................. 124 Assigning an IP access group to a Gigabit Ethernet port .................................................................... 124 Assigning an IPv6 address to a Gigabit Ethernet port ........................................................................ 125 Assigning a Gigabit Ethernet port to a VLAN ...................................................................................... 126 Enabling/disabling the IGMP client service on a Gigabit Ethernet port ............................................. 126 Configuring the MTU size on a Gigabit Ethernet interface (5.4)......................................................... 127 Displaying the Gigabit Ethernet interface configuration .................................................................... 128 Displaying the 10Gigabit Ethernet interface configuration ................................................................ 129 Displaying the Gigabit Ethernet interface statistics ........................................................................... 130 CONFIGURING LOOPBACK INTERFACES.............................................................................................................. 131 Enabling interface loopback mode ..................................................................................................... 132 Configuring an IPv6 address on a loopback interface ........................................................................ 132 Configuring an IPv4 address on a loopback interface ........................................................................ 133 Assigning an access group to a loopback interface ............................................................................ 133 Configuring a log message source IP address..................................................................................... 134 Configuring a loopback interface as source IP address on FTP/TFTP packets ................................... 134 Setting the source IP address of lawful intercept packets to the loopback IP interface ..................... 135 Configuring trunk interfaces ............................................................................................................... 135 Creating a trunk interface................................................................................................................... 135 Configuring a trunk description .......................................................................................................... 136 Assigning an IP address to a trunk interface ...................................................................................... 137 Enabling/disabling a trunk interface .................................................................................................. 138 Adding a GigE port to a trunk interface .............................................................................................. 138 Enabling IGMP client services on a trunk interface ............................................................................ 139 Applying an IP access group to a trunk interface ............................................................................... 139 Displaying a trunk interface configuration ......................................................................................... 140 Displaying ARP entries from a trunk interface.................................................................................... 141 CONFIGURING DNS ..................................................................................................................................... 142 CONFIGURING DHCP ................................................................................................................................... 142 Using the DHCP insert function........................................................................................................... 143 DHCP and DHCPv6 Leasequery ........................................................................................................... 144 CONFIGURING LINK AGGREGATION CONTROL PROTOCOL (LACP) (5.4) ................................................................. 146 Enabling the LACP global configuration ............................................................................................. 146 Setting LACP port priority ................................................................................................................... 147 Setting the LACP system port priority ................................................................................................. 147

CASA CMTS Displaying LACP group information .................................................................................................... 147 Configuring and displaying LACP port priority on GigE interfaces ...................................................... 148 Configuring and displaying LACP trunk interfaces .............................................................................. 149 Displaying the LACP system ID............................................................................................................ 150 CONFIGURING IS-IS ROUTING PROTOCOL (5.4 ONLY) ........................................................................................ 150 Configuring IPv4 IS-IS under a GigE Port............................................................................................. 150 Configuring IPv6 IS-IS under a GigE port............................................................................................. 151 Configuring an IS-IS circuit type on a GigE interface .......................................................................... 151 Configuring IS-IS point-to-point links .................................................................................................. 152 Configuring the complete sequence number PDU (CSNP) interval ..................................................... 153 Configuring the IS-IS Hello interval ..................................................................................................... 153 Configuring the IS-IS Multiplier for Hello holding time ....................................................................... 154 Enabling padding on IS-IS Hello packets ............................................................................................. 155 Configuring the IS-IS default metric .................................................................................................... 155 Configuring the authentication password for a GigE interface .......................................................... 156 Configuring the IS-IS priority ............................................................................................................... 157 Configuring the IS-IS retransmit-interval ............................................................................................ 157 Configuring IS-IS router area tag ........................................................................................................ 158 Displaying the IS-IS command list ....................................................................................................... 158 Specifying the IS-IS IPv6 address family parameters .......................................................................... 159 Configuring the IS-IS router area authentication password ............................................................... 161 Configuring the IS-IS router authentication key chain ........................................................................ 162 Configuring the IS-IS router authentication mode .............................................................................. 162 Configuring the IS-IS router authentication send-only option ............................................................ 163 Configuring the IS-IS router default route distribution ....................................................................... 164 Configuring the IS-IS router domain authentication password .......................................................... 164 Configuring the IS area types.............................................................................................................. 165 Configuring the IS-IS LSP generation interval ..................................................................................... 166 Configuring the IS-IS LSP lifetime ........................................................................................................ 166 Configuring the IS-IS route redistribution metric style........................................................................ 167 Configuring the network entity title (NET).......................................................................................... 167 Enabling the IS-IS dynamic hostname capability ................................................................................ 168 Configuring IS-IS passive interfaces .................................................................................................... 168 Configuring IS-IS to redistribute route advertisements from other protocols .................................... 169 Setting the IS-IS overload bit............................................................................................................... 170

CASA CMTS Setting the IS-IS shortest path first (SPF) calculations ........................................................................ 171 Setting the IPv4 summary address prefix ........................................................................................... 172 Displaying the IS-IS area configuration............................................................................................... 172 Displaying the IS-IS counter statistics ................................................................................................. 173 Displaying the IS-IS link state database .............................................................................................. 174 Displaying the IS-IS interface statistics ............................................................................................... 175 Displaying the IS-IS neighbor routers.................................................................................................. 176 Displaying the IS-IS topology information .......................................................................................... 176 Displaying the IPv4 and IPv6 IS-IS routing table ................................................................................. 177 CONFIGURING PROTOCOL INDEPENDENT MULTICAST IN SPARSE MODE ................................................................. 177 Enabling PIM-SM on a GigE or loopback interface ............................................................................. 178 Displaying the current PIM-SM interface and neighbor configurations ............................................. 178 Configuring rendezvous point addresses ............................................................................................ 178 Configuring the rendezvous point candidate ...................................................................................... 180 Configuring the bootstrap router candidate....................................................................................... 181 Setting the Shortest Path Tree threshold ............................................................................................ 182 Configuring source-specific multicast ................................................................................................. 183 CONFIGURING THE OSPF ROUTING PROTOCOL ................................................................................................. 183 Entering OSPF configuration mode..................................................................................................... 185 Exiting OSPF configuration mode ....................................................................................................... 185 Enabling OSPF area authentication .................................................................................................... 185 Configuring the OSPF area default cost .............................................................................................. 186 Configuring the OSPF area filter list.................................................................................................... 187 Configuring the OSPF area export list ................................................................................................. 187 Configuring the OSPF area import list ................................................................................................ 188 Configuring the OSPF area NSSA ........................................................................................................ 189 Configuring the OSPF area range ....................................................................................................... 190 Configuring the OSPF area shortcut ................................................................................................... 191 Configuring the OSPF area stub .......................................................................................................... 191 Configuring the OSPF area virtual link ................................................................................................ 192 Configuring the OSPF interface auto cost ........................................................................................... 194 Configuring OSPF-compatible RFC1583 .............................................................................................. 194 Configuring OSPF control-distribution default information ................................................................ 195 Configuring the OSPF default metric .................................................................................................. 196 Configuring the OSPF administrative distance ................................................................................... 197

CASA CMTS Displaying the OSPF command list ..................................................................................................... 197 Configuring the OSPF neighbor router ................................................................................................ 198 Configuring OSPF routing on an IP network ....................................................................................... 199 Configuring the OSPF ABR type .......................................................................................................... 200 Configuring the OSPF route ID ............................................................................................................ 200 Configuring the OSPF passive interface .............................................................................................. 201 Configuring the OSPF distribute list .................................................................................................... 201 Configuring OSPF route redistribution ................................................................................................ 202 Configuring the OSPF refresh parameters .......................................................................................... 203 Configuring the OSPF route ID ............................................................................................................ 204 Configuring the OSPF routing timers .................................................................................................. 204 Configuring IP OSPF authentication.................................................................................................... 205 Configuring the IP OSPF authentication-key ....................................................................................... 206 Configuring the IP OSPF cost .............................................................................................................. 206 Configuring the IP OSPF dead interval ................................................................................................ 207 Configuring the IP OSPF Hello interval................................................................................................ 208 Configuring the IP OSPF message digest key ...................................................................................... 208 Configuring the IP OSPF retransmit interval ....................................................................................... 209 Configuring the IP OSPF transmit delay .............................................................................................. 210 Displaying OSPF general information ................................................................................................. 210 Displaying the OSPF internal routing table entries ............................................................................. 211 Displaying the OSPF database for a specified router .......................................................................... 211 Displaying OSPF interface information ............................................................................................... 211 Displaying OSPF neighbor information ............................................................................................... 212 Displaying the OSPF routing table ...................................................................................................... 212 Displaying IPv4 route information ...................................................................................................... 212 Displaying IPv6 route information ...................................................................................................... 213 Sample OSPF configurations ............................................................................................................... 214 CONFIGURING THE ROUTING INFORMATION PROTOCOL ...................................................................................... 214 Entering RIP configuration mode ........................................................................................................ 215 Exiting RIP configuration mode .......................................................................................................... 215 Configuring the RIP default route ....................................................................................................... 215 Configuring the RIP default metric ..................................................................................................... 216 Configuring the RIP administrative distance ...................................................................................... 217 Configuring the RIP filter list ............................................................................................................... 217

CASA CMTS Displaying the RIP command list ........................................................................................................ 218 Configuring the RIP neighbor router ................................................................................................... 219 Configuring RIP routing on an IP network .......................................................................................... 219 Configuring the RIP offset list ............................................................................................................. 220 Configuring the RIP passive interface ................................................................................................. 221 Redistributing routes over RIP ............................................................................................................ 221 Configuring RIP static routes .............................................................................................................. 222 Configuring the RIP router map .......................................................................................................... 223 Configuring the RIP routing timers ..................................................................................................... 223 Configuring the RIP version ................................................................................................................ 224 Configuring the IP RIP authentication key chain ................................................................................ 224 Configuring an IP RIP authentication string ....................................................................................... 225 Configuring the IP RIP authentication mode ...................................................................................... 226 Displaying RIP routing information..................................................................................................... 226 Displaying RIP status information ...................................................................................................... 227 Displaying IPv4 route information ...................................................................................................... 227 Displaying IPv6 route information ...................................................................................................... 228 CONFIGURING THE BGP ROUTING PROTOCOL (RELEASE 5.4 AND LATER) ............................................................... 229 Enabling BGP routing.......................................................................................................................... 229 Setting the BGP distance .................................................................................................................... 230 BGP decision processing ..................................................................................................................... 231 Enabling BGP networks....................................................................................................................... 232 Configuring BGP routes ...................................................................................................................... 232 Enabling route aggregation ................................................................................................................ 232 Configuring BGP route redistribution ................................................................................................. 233 Defining BGP peers ............................................................................................................................. 234 Defining BGP peer passwords ............................................................................................................. 235 Configuring BGP peers ........................................................................................................................ 236 Peer filtering ....................................................................................................................................... 242 Configuring BGP peer groups.............................................................................................................. 245 Setting the BGP address family........................................................................................................... 246 Specifying the BGP IPv6 address family parameters .......................................................................... 247 Configuring autonomous systems ...................................................................................................... 252 Defining the AS path access list .......................................................................................................... 252 Using the BGP communities attribute ................................................................................................ 253

CASA CMTS Configuring BGP community lists ....................................................................................................... 254 BGP community in route map ............................................................................................................. 255 Using the BGP community attribute ................................................................................................... 255 Displaying access class information (Release 5.4) .............................................................................. 259 Displaying BGP routes......................................................................................................................... 260 Clearing and reestablishing BGP routes ............................................................................................. 261 Enabling capability negotiation .......................................................................................................... 263 Configuring route reflectors................................................................................................................ 264 Verifying BGP routes prior to advertisement ...................................................................................... 265 IP ACCESS CONTROL ..................................................................................................................................... 266 Creating and removing ACLs............................................................................................................... 266 Entering and exiting ACL editing mode............................................................................................... 267 Adding and removing control rules .................................................................................................... 267 Adding remark statements to the ACL ................................................................................................ 269 Displaying a control rule in an ACL ..................................................................................................... 269 Displaying ACL names ......................................................................................................................... 270 Numbering control rules in ACLs......................................................................................................... 270 Applying an ACL to an IP interface (C3200 and C10200 only) ............................................................ 271 Removing the ACL from an IP interface .............................................................................................. 272 Creating and deleting IP access classes .............................................................................................. 272 CONFIGURING ROUTE MAPS ........................................................................................................................... 273 Creating a named and sequenced route-map .................................................................................... 274 Using the route-map match commands ............................................................................................. 274 Matching BGP autonomous system paths.......................................................................................... 275 Matching the BGP community list ...................................................................................................... 275 Matching IPv4 and IPv6 addresses ..................................................................................................... 276 Matching route metrics ...................................................................................................................... 277 Matching route origins ....................................................................................................................... 277 Matching peer routes ......................................................................................................................... 278 Matching route tags ........................................................................................................................... 278 Using the route-map set commands .................................................................................................. 279 Modifying BGP autonomous system paths ......................................................................................... 279 Setting the atomic aggregate ............................................................................................................. 280 Modifying the BGP community attribute............................................................................................ 280 Modifying next-hop IP addresses........................................................................................................ 281

CASA CMTS Setting the BGP local-preference path attribute ................................................................................ 282 Setting the metric for destination routing .......................................................................................... 282 Modifying route origins ...................................................................................................................... 283 Setting the BGP originator-id attribute .............................................................................................. 283 Setting the BGP weight attribute ........................................................................................................ 284 Displaying route-map details .............................................................................................................. 284 CONFIGURING VIRTUAL LOCAL AREA NETWORKS (VLANS) ................................................................................. 284 Configuring a VLAN............................................................................................................................. 285 Configuring a VLAN description .......................................................................................................... 285 Configuring up to six VLANs concurrently (Release 5.4 and later) ...................................................... 286 Configuring VLANs in a range (Release 5.4 and later) ........................................................................ 286 Configuring the MAC address on each VLAN interface....................................................................... 286 Enabling/disabling VLAN Interfaces (5.4) ........................................................................................... 287 Assigning a Gigabit Ethernet port to a VLAN ...................................................................................... 287 Assigning a 10Gigabit Ethernet port to a VLAN.................................................................................. 288 Removing a Gigabit Ethernet port from a VLAN ................................................................................. 288 Removing a 10Gigabit Ethernet port from a VLAN ............................................................................ 289 Assigning an IPv4 address to a VLAN.................................................................................................. 289 Assigning an IPv6 address to a VLAN.................................................................................................. 290 Rate limiting multicast traffic over a VLAN interface ......................................................................... 291 Assign a QAM port to a VLAN ............................................................................................................. 291 Assigning an IP access group to a VLAN interface .............................................................................. 292 Assigning a trunk to a VLAN interface ................................................................................................ 293 Displaying all VLAN configurations ..................................................................................................... 294 Displaying a VLAN interface (Release 5.4) .......................................................................................... 294 Displaying ARP entries from the current VLAN ................................................................................... 295 CONFIGURING L2VPN ................................................................................................................................. 296 Specifying ports/interfaces on the NSI side of the L2VPN VLAN ......................................................... 296 Specifying GigE/trunk interfaces on the L2VPN VLAN ........................................................................ 297 Preventing and permitting station movement and local forwarding ................................................. 297 Displaying the station movement and local forwarding configuration .............................................. 298 Displaying configured L2VPNs ............................................................................................................ 298 Displaying L2VPN statistics on QAM modules .................................................................................... 299 CONFIGURING TACACS (RELEASE 5.4) ........................................................................................................... 299 Configuring the TACACS host IP .......................................................................................................... 299

CASA CMTS Configuring a TACACS key .................................................................................................................. 300 Enabling password authentication at the TACACS+ server................................................................. 300 Disabling the TACACS+ authentication password............................................................................... 300 Enabling ASCII clear text authentication ............................................................................................ 301 Using RADIUS/TACACS+ Server for default server group for AAA login authentication ..................... 301 Configuring the AAA authentication login .......................................................................................... 301 Configuring AAA authorization ........................................................................................................... 302 Enabling accounting ........................................................................................................................... 303 Command accounting ......................................................................................................................... 303 Configuring AAA accounting for start-stop events ............................................................................. 303 Configuring AAA RADIUS-source loopback interface configuration ................................................... 304 Disabling the AAA RADIUS source ...................................................................................................... 304 Configuring the RADIUS server ........................................................................................................... 304 Disabling a specified RADIUS server or RADIUS encryption key ......................................................... 305 Displaying the AAA configuration ....................................................................................................... 305 STREAM CONFIGURATION AND MANAGEMENT................................................................................................... 306 Modes for mapping input streams to QAM output channels ............................................................. 306 Enabling manual operation mode ...................................................................................................... 306 Enabling RPC mode ............................................................................................................................. 307 Using auto-operation mode................................................................................................................ 308 Enabling auto-multiplex mode ........................................................................................................... 308 Enabling Group-4-port operation mode ............................................................................................. 309 Enabling Group-2-port operation mode ............................................................................................. 310 Setting the de-jitter interval ............................................................................................................... 311 Entering stream configuration mode.................................................................................................. 312 Ending stream configuration mode .................................................................................................... 312 Setting the stream source IP address ................................................................................................. 313 Setting the stream destination IP address .......................................................................................... 313 Setting the stream source UDP port ................................................................................................... 314 Setting the stream destination UDP port............................................................................................ 315 Displaying configured streams ........................................................................................................... 315 Binding a stream to a QAM output channel ....................................................................................... 316 Displaying unmapped streams ........................................................................................................... 317 Stream configuration example ........................................................................................................... 318 CONFIGURING DOWNSTREAM QAM PORTS ...................................................................................................... 319

CASA CMTS Entering QAM interface configuration mode ..................................................................................... 319 Ending QAM interface configuration mode ........................................................................................ 320 Enabling QAM output ports ................................................................................................................ 320 Disabling QAM output port ................................................................................................................ 321 Enabling QAM output channels .......................................................................................................... 321 Disabling QAM output channels ......................................................................................................... 322 Setting the QAM port IP address and subnet mask ............................................................................ 322 Setting the QAM port MAC address ................................................................................................... 323 Setting the QAM modulation type ...................................................................................................... 324 Setting the QAM channel annex ......................................................................................................... 325 Setting the QAM frequency ................................................................................................................ 326 Setting the QAM output power .......................................................................................................... 327 Setting the QAM interleave level ........................................................................................................ 328 Setting the QAM spectral inversion .................................................................................................... 329 Displaying QAM interface configurations ........................................................................................... 330 Displaying QAM channel counters and utilization rates ..................................................................... 331 Displaying QAM downstream channel sets ........................................................................................ 331 CONFIGURING UPSTREAM PORT INTERFACES ..................................................................................................... 332 About upstream interface configurations........................................................................................... 332 Multiple upstream logical channels, dynamic channel width switching, independent power levels 333 Entering the upstream port interface configuration mode ................................................................ 334 Ending an upstream port interface configuration session .................................................................. 334 Enabling upstream ports .................................................................................................................... 335 Disabling upstream ports ................................................................................................................... 335 Entering an upstream logical interface description ............................................................................ 336 Showing upstream port interface configurations ............................................................................... 337 Displaying upstream interface status ................................................................................................. 341 Setting the upstream logical channel frequency ................................................................................ 343 Setting the upstream logical channel width ....................................................................................... 344 Changing the upstream MAP size ....................................................................................................... 345 Setting the upstream input power level ............................................................................................. 346 Adjusting the upstream input power threshold .................................................................................. 347 Adjusting the upstream input power level .......................................................................................... 348 Setting the upstream map-advance ................................................................................................... 349 Enabling the upstream logical-channels ............................................................................................. 351

CASA CMTS Disabling the upstream logical-channels ............................................................................................ 351 Setting upstream channel data and ranging backoff values .............................................................. 352 Configuring the ranging hold-off priority bit ...................................................................................... 356 Setting the upstream channel mini-slot size ....................................................................................... 357 Enabling the upstream channel class identifier .................................................................................. 358 Setting the upstream channel S-CDMA frame interval ....................................................................... 359 Assigning modulation profiles to an upstream interface.................................................................... 360 Specifying multiple secondary profiles to an upstream interface ....................................................... 361 Setting the upstream channel pre-equalization ................................................................................. 361 Setting the provisioned attribute mask .............................................................................................. 362 Enabling/disabling ingress noise cancellation .................................................................................... 364 Setting up voice bandwidth reserve percentage ................................................................................ 365 Configuring the QoS traffic bandwidth reserve percentage ............................................................... 366 Applying spectrum rules to upstream channels .................................................................................. 367 Enabling rate limiting ......................................................................................................................... 368 Displaying the upstream channel utilization rates ............................................................................. 369 Displaying the upstream channel signal quality ................................................................................. 370 Displaying the upstream channel burst nose...................................................................................... 370 Displaying upstream channel sets ...................................................................................................... 372 Displaying voice information on upstream interfaces ........................................................................ 373 CONFIGURING IP-BUNDLE INTERFACES ............................................................................................................. 373 Adding the primary IP interface.......................................................................................................... 374 Adding a secondary IP bundle interface ............................................................................................. 375 Remove an IP bundle secondary IP address........................................................................................ 375 Adding primary and secondary IPv6 interfaces .................................................................................. 376 Specifying the IPv6 local link address ................................................................................................. 377 Displaying the IPv6 local link address ................................................................................................. 378 Adding a helper-address ..................................................................................................................... 378 Configure IP bundle sub-interfaces (Release 5.4) ............................................................................... 379 Applying IP bundle interfaces to MAC domains .................................................................................. 380 Classifying CPE devices for DHCP option 60 string matching ............................................................. 381 Configuring the IP RIP authentication key chain ................................................................................ 382 Configuring an IP RIP authentication string ....................................................................................... 383 Configuring the IP RIP authentication mode ...................................................................................... 383 Displaying the IP bundle interface configuration and statistics ......................................................... 384

CASA CMTS CONFIGURING DOCSIS MAC DOMAINS .......................................................................................................... 385 Displaying domain interface configurations ....................................................................................... 386 Creating new domain interfaces ......................................................................................................... 387 Binding IP-bundle interfaces ............................................................................................................... 388 Binding upstream interfaces ............................................................................................................... 388 Deleting upstream interface bindings ................................................................................................ 389 Binding downstream interfaces .......................................................................................................... 390 Binding secondary downstream interfaces (5.4 only)......................................................................... 390 Deleting downstream interface bindings............................................................................................ 391 Enabling MAC domain interfaces ....................................................................................................... 392 Disabling MAC domain interfaces ...................................................................................................... 392 Setting MAC domain interface IP addresses ....................................................................................... 393 Setting MAC domain interface IPv6 addresses (Rel. 5.2 and earlier).................................................. 393 Removing MAC domain interface IPv6 addresses (Rel. 5.2 and earlier) ............................................. 394 Setting the helper-address (Software Ver. 5.2 and earlier) ............................................................... 394 Configuring MAC domain IP bundle interfaces ................................................................................... 396 Setting the domain sync-interval ........................................................................................................ 397 Specifying the intial technique for moving cable modems to upstream channels.............................. 397 Setting the upstream insertion-interval .............................................................................................. 398 Configuring the MDD interval ............................................................................................................. 399 Enabling a domain interface gateway IP address .............................................................................. 400 Enabling a domain interface TFTP proxy ............................................................................................ 401 Rejecting modem registrations with TFTP enforce ............................................................................. 401 Displaying modem registrations that have bypassed TFTP ................................................................ 402 Enabling/disabling IP policies on a domain interface ......................................................................... 402 Configuring multicast on MAC domain interfaces .............................................................................. 403 Enabling/disabling DHCP authorization on a MAC domain interface ................................................ 404 Configuring channel bonding on MAC domain interface .................................................................... 404 Enabling MAC domain multicast DSID forwarding ............................................................................. 405 Configuring IP-provisioning-mode on a MAC domain interface ......................................................... 406 Configuring MAC domain IPv6 router advertisement parameters ..................................................... 406 Displaying the router advertisement table ......................................................................................... 409 Configuring BPI+ on a MAC domain interface .................................................................................... 409 Configuring cable modem trap generation and interval .................................................................... 410 Displaying the MAC domain interface configuration.......................................................................... 411

CASA CMTS Displaying MAC domain statistics ...................................................................................................... 411 CONFIGURING SERVICE GROUPS ...................................................................................................................... 412 Creating a new service group ............................................................................................................. 412 Binding upstream interfaces ............................................................................................................... 413 Binding downstream interfaces .......................................................................................................... 414 Displaying service groups ................................................................................................................... 415 Displaying MAC domain downstream service groups (Release 5.4) ................................................... 416 Displaying specific MAC domain downstream service groups ............................................................ 416 Displaying a specific downstream service group ................................................................................ 417 Displaying MAC domain upstream service group information ........................................................... 417 CONFIGURING BONDING GROUPS .................................................................................................................... 417 Creating new downstream/upstream bonding groups ...................................................................... 418 Binding upstream interfaces to a bonding group ............................................................................... 419 Binding downstream interfaces to a bonding group .......................................................................... 420 Displaying bonding groups ................................................................................................................. 421 Setting up the receive channel configuration ..................................................................................... 421 Assigning a receive module ................................................................................................................ 422 Assigning a receive channel ................................................................................................................ 422 Displaying the receive channel configuration ..................................................................................... 423 CONFIGURING MODULATION PROFILES ............................................................................................................. 424 Predefined modulation-profile 1 parameters ..................................................................................... 424 Predefined modulation-profile 2 parameters ..................................................................................... 425 Predefined modulation-profile 3 parameters ..................................................................................... 425 Predefined modulation-profile 4 parameters ..................................................................................... 425 Predefined modulation-profile 5 parameters ..................................................................................... 426 Configuring a modulation profile........................................................................................................ 427 Configuring TDMA burst types............................................................................................................ 427 Configuring ATDMA burst types ......................................................................................................... 429 Configuring MTDMA burst types ........................................................................................................ 431 Auto-mode MTDMA-type modulation profile configuration .............................................................. 431 Manual mode MTDMA-type modulation profile configuration.......................................................... 431 Configuring SCDMA burst types.......................................................................................................... 433 Retrieving configured modulation profiles ......................................................................................... 434 Removing modulation profiles ............................................................................................................ 435 Upstream burst noise detection and monitoring ................................................................................ 435

CASA CMTS CONFIGURING MULTICAST OPERATIONS ........................................................................................................... 436 Setting the multicast maximum channel utilization ........................................................................... 437 Enabling/disabling multicast session authorization ........................................................................... 438 Enabling/disabling the multicast single security association identifier .............................................. 438 Configuring a multicast session authorization profile ........................................................................ 439 Configuring a multicast session rule ................................................................................................... 439 Configuring the default action for a multicast join request ................................................................ 440 Configuring a maximum session number for multicast authorization ............................................... 441 Assigning a profile to multicast authorization .................................................................................... 441 Displaying multicast authorization configurations ............................................................................. 441 Displaying multicast authorization sessions ....................................................................................... 442 Configuring a multicast group table ................................................................................................... 442 Configuring multicast group encryption ............................................................................................. 444 Configuring multicast group QoS........................................................................................................ 444 Configuring a multicast group service class........................................................................................ 445 Configuring a default service class for a multicast group ................................................................... 447 Displaying multicast group configurations ......................................................................................... 447 Creating static multicast sessions ....................................................................................................... 448 Configuring redundant downstream multicast .................................................................................. 450 Removing a static multicast session ................................................................................................... 451 Displaying static multicast sessions .................................................................................................... 451 Configuring IGMP packet filtering ...................................................................................................... 452 Displaying all filtering settings in the running configuration ............................................................. 452 Managing multicast for IPTV as a limited multicast session .............................................................. 453 Limited multicast sessions .................................................................................................................. 453 General multicast sessions ................................................................................................................. 453 How to identify limited multicast sessions ......................................................................................... 453 Multicast Listener Discovery (RFC2710).............................................................................................. 454 CONFIGURING CABLE SERVICE CLASSES ............................................................................................................. 454 Creating a cable service class ............................................................................................................. 454 Specifying the cable service class parameters .................................................................................... 455 Displaying service class parameters ................................................................................................... 457 Applying service classes to modem configuration files....................................................................... 459 CONFIGURING PACKETCABLE ......................................................................................................................... 460 Enabling PacketCable operation ......................................................................................................... 461

CASA CMTS Displaying event messages ................................................................................................................. 461 Enabling DSCP checking ...................................................................................................................... 461 Configuring event messages ............................................................................................................... 462 Configuring an IP address ................................................................................................................... 462 Configuring an FTP user ...................................................................................................................... 462 Configuring FTP user passwords ......................................................................................................... 463 Configuring the T0 timer..................................................................................................................... 463 Configuring the T1 timer..................................................................................................................... 463 Configuring network layer signaling (NLS) ......................................................................................... 464 Configuring maximum normal calls .................................................................................................... 464 Configuring maximum emergency calls.............................................................................................. 465 Configuring inactive call aging (Rel. 6.1 and later) ............................................................................. 465 Enabling PacketCable admission control preempt voice priority........................................................ 466 Enabling PacketCable Multimedia (PCMM)........................................................................................ 466 Enabling Packetcable Multimedia version setup ................................................................................ 466 Displaying Packetcable Multimedia specifications ............................................................................. 467 Setting the cable service flow timeout................................................................................................ 468 Assigning dynamic service flows to downstream channels ................................................................ 468 Displaying the PCMM policy server .................................................................................................... 469 Displaying PCMM multicast................................................................................................................ 469 Displaying the PacketCable configuration .......................................................................................... 469 Specifying a timeout for the RKS server .............................................................................................. 470 Specifying a retry count for the RKS server ......................................................................................... 470 Specifying batch file send mode ......................................................................................................... 471 Specifying the batch file sending time interval ................................................................................... 471 Specifying the maximum size of the event message batch file ........................................................... 472 Specifying the maximum messages in the batch file .......................................................................... 472 Specifying the RKS server media alive time ........................................................................................ 473 Specifying the RKS server maximum gates ......................................................................................... 473 Displaying RKS server information...................................................................................................... 473 Displaying live gate summary information ......................................................................................... 474 Displaying upstream or downstream gate information ..................................................................... 474 Displaying the total gate number ....................................................................................................... 474 Displaying COPS server information ................................................................................................... 475 CONFIGURING DSG ..................................................................................................................................... 475

CASA CMTS Creating a new DSG tunnel ................................................................................................................. 475 Creating a DSG tunnel-group .............................................................................................................. 476 Associating a DSG tunnel with a tunnel-group ................................................................................... 476 Displaying DSG tunnel groups ............................................................................................................ 477 Ending a DSG tunnel-group configuration session ............................................................................. 477 Assigning a destination MAC address to a DSG tunnel....................................................................... 478 Assigning a client list to a DSG tunnel ................................................................................................ 478 Assigning a service-class to a DSG tunnel ........................................................................................... 479 Assigning a classifier to a DSG tunnel ................................................................................................. 480 Displaying the DSG tunnel configuration (Release 5.4) ...................................................................... 481 Displaying the cable DSG tunnel configuration (Release 5.4) ............................................................. 481 Associating a downstream channel with a DSG tunnel-group ........................................................... 482 Displaying the downstream DSG configuration (Release 5.4) ............................................................ 482 Displaying DSG channel and tunnel group information...................................................................... 483 Setting a DSG timer to a downstream channel................................................................................... 483 Assigning a DSG vendor-parameter ID to a downstream channel ..................................................... 484 Assigning a DSG channel-list to a downstream channel ..................................................................... 484 Assigning DSG DCD ENABLE to a downstream channel ...................................................................... 485 Setting a DSG time interval on a downstream channel ...................................................................... 485 Displaying the DSG downstream-table settings ................................................................................. 486 Configuring a DSG client list ............................................................................................................... 487 Displaying DSG client lists ................................................................................................................... 487 Configuring DSG vendor parameters .................................................................................................. 488 Displaying DSG vendor parameters .................................................................................................... 488 Configuring a DSG channel list ........................................................................................................... 489 Displaying a DSG channel list.............................................................................................................. 489 Configuring DSG timers ...................................................................................................................... 489 Displaying DSG timers......................................................................................................................... 490 Configuring DSG unicast ..................................................................................................................... 490 Displaying DSG statistics..................................................................................................................... 491 Displaying the DSG running configuration ......................................................................................... 491 Using the DSG feature ........................................................................................................................ 491 Verify DSG DCD message and DSG data forwarding .......................................................................... 493 CONFIGURING DOCSIS BPI/BPI+ ................................................................................................................. 494 Configuring shared secrets to protect the modem configuration file ................................................. 494

CASA CMTS Adding the privacy certificate (DOCSIS 3.0 only) ................................................................................ 496 Displaying the privacy certificate configuration (DOCSIS 3.0 only) .................................................... 498 Enforcing BPI and BPI+ ....................................................................................................................... 498 Changing the security association descriptor TLV length ................................................................... 499 Setting the privacy hotlist (DOCSIS 3.0 only) ...................................................................................... 499 Configuring an encryption algorithm.................................................................................................. 501 Managing revocation certificates ....................................................................................................... 501 Configuring the source address verification rule ................................................................................ 504 Enabling SAV authorization ................................................................................................................ 504 Displaying the SAV configuration ....................................................................................................... 504 Enabling configuration file learning ................................................................................................... 505 Configuring TFTP proxies .................................................................................................................... 505 Displaying config file learning status .................................................................................................. 506 Displaying the TFTP option setting ..................................................................................................... 506 Configuring the EAE exclusion list ....................................................................................................... 506 Adding cable modems to the EAE exclusion list .................................................................................. 506 Displaying the EAE exclusion list ......................................................................................................... 507 SOURCE ADDRESS VERIFICATION (SAV) ........................................................................................................... 507 SPECTRUM MANAGEMENT............................................................................................................................. 509 CSM algorithm .................................................................................................................................... 510 Creating spectrum rules...................................................................................................................... 510 Exiting spectrum rule mode ................................................................................................................ 510 Setting a frequency band .................................................................................................................... 511 Setting a discrete frequency ............................................................................................................... 512 Setting the hopping period ................................................................................................................. 513 Setting the hopping priority ................................................................................................................ 513 Setting the channel-width adjustment range ..................................................................................... 514 Specifying a modulation profile SNR................................................................................................... 514 Specifying a modulation profile SNR threshold .................................................................................. 515 Specifying the hop-back threshold...................................................................................................... 516 Default SNR threshold for different modulations ............................................................................... 517 Setting the FEC threshold.................................................................................................................... 517 Assigning a spectrum rule to an upstream interface .......................................................................... 518 Assigning modulation profiles to an upstream interface.................................................................... 519 Specifying multiple secondary profiles to an upstream interface (Release 5.4 and later) ................. 520

CASA CMTS Setting the monitoring period ............................................................................................................ 521 Displaying hopping history ................................................................................................................. 521 Displaying the spectrum map ............................................................................................................. 522 Displaying the spectrum noise level.................................................................................................... 523 Enabling CM hopping ......................................................................................................................... 524 Displaying CM hopping history ........................................................................................................... 524 Considerations when using CSM ......................................................................................................... 525 Frequency hop case study ................................................................................................................... 525 CSM configuration example................................................................................................................ 527 SPECTRUM MEASUREMENT (DOCSIS 3.0 ONLY) ............................................................................................... 527 Displaying spectrum measurement results......................................................................................... 528 Running spectrum analysis across the entire spectrum...................................................................... 530 CONFIGURING LOAD BALANCING ..................................................................................................................... 530 Enabling and disabling load balancing ............................................................................................... 533 Enabling load balancing across MAC domains ................................................................................... 534 General load balancing groups ........................................................................................................... 534 Load balancing basic rules .................................................................................................................. 537 Load balance execution rules.............................................................................................................. 538 Load balancing policies ....................................................................................................................... 544 Restricted load balance groups .......................................................................................................... 545 Exclusion lists ...................................................................................................................................... 550 Restricted cable modems.................................................................................................................... 551 CM frequency and channel relocation ................................................................................................ 554 Displaying load balancing information ............................................................................................... 562 Command ordering ............................................................................................................................. 563 Command default values .................................................................................................................... 564 Sample configuration.......................................................................................................................... 564 CONFIGURING CHANNEL BONDING OPERATIONS................................................................................................. 570 Service group configuration................................................................................................................ 570 DOCSIS-MAC interface configuration ................................................................................................. 571 Channel bonding example .................................................................................................................. 572 CREATING STATIC CM BONDING GROUPS ......................................................................................................... 573 Adding a static downstream CM bonding group ................................................................................ 574 Adding a static upstream CM bonding group ..................................................................................... 574 Setting the provisioned attribute mask in an upstream/downstream bonding group ....................... 575

CASA CMTS Adding an upstream channel to a bonding group .............................................................................. 576 Adding a downstream channel to a bonding group ........................................................................... 576 Setting the DSID re-sequencing wait time in a downstream bonding group ...................................... 577 Setting the DSID re-sequencing warning threshold in a downstream bonding group ........................ 577 QOS SUPPORT ............................................................................................................................................ 578 QoS support in DQM modules ............................................................................................................ 578 QoS support in DCU modules .............................................................................................................. 578 QoS support in switch fabric and Gigabit Ethernet interfaces ............................................................ 579 CONFIGURING QOS ..................................................................................................................................... 579 Configuring the service class (DOCSIS 1.1).......................................................................................... 580 Showing the service class.................................................................................................................... 580 QoS class and policy (C3200, C10200, C10G only) .............................................................................. 581 CONFIGURING SNMP (ENHANCED FOR REL. 5.4 AND LATER) .............................................................................. 584 Configuring the SNMP engineID ......................................................................................................... 585 Enabling SNMP traps .......................................................................................................................... 585 Setting an SNMP traphost .................................................................................................................. 586 Configuring SNMP server contact and location strings ...................................................................... 586 Configuring the SNMP trap source IP address .................................................................................... 587 Enabling SNMP inform requests ......................................................................................................... 587 Setting the SNMP community ............................................................................................................. 588 Disabling default SNMP public and private community ..................................................................... 588 Configuring the SNMP access table .................................................................................................... 588 Deleting the SNMP access table ......................................................................................................... 589 Configuring the community table ....................................................................................................... 590 Deleting the SNMP community table ................................................................................................. 590 Configuring the notification table....................................................................................................... 590 Deleting the notification table ............................................................................................................ 591 Configuring the securityToGroup table............................................................................................... 591 Configuring the TargetAddress table .................................................................................................. 592 Deleting the TargetAddress table ....................................................................................................... 593 Configuring the TargetParameter table ............................................................................................. 593 Deleting the TargetParameter table................................................................................................... 594 Configure the ViewTreeFamily table................................................................................................... 594 Deleting the ViewTreeFamily table..................................................................................................... 595 Configuring the SNMP user table ....................................................................................................... 595

CASA CMTS Deleting the SNMP user table ............................................................................................................. 596 Displaying the SNMP configuration and statistics .............................................................................. 596 Monitoring the SNMP process at the CMTS ....................................................................................... 600 CONFIGURING IPDR .................................................................................................................................... 600 Displaying IPDR connections............................................................................................................... 601 Displaying IPDR sessions ..................................................................................................................... 601 Displaying IPDR statistics from the running configuration ................................................................. 602 Restarting and stopping the IPDR daemon......................................................................................... 602 Configuring IPDR collector mastership ............................................................................................... 603 Enabling IPDR service types ................................................................................................................ 603 Configuring the IPDR keepalive time interval ..................................................................................... 604 Configuring the IPDR acknowledge sequence interval ....................................................................... 604 Configuring the IPDR ACK interval ...................................................................................................... 604 Configuring the IPDR spectrum measurement interval ...................................................................... 605 Configuring the IPDR connection to be primary ................................................................................. 605 Configuring the IPDR loopback interface ............................................................................................ 605 CONFIGURING IPSEC .................................................................................................................................... 606 Enabling and disabling the IPsec service ............................................................................................ 606 Configuring the IPsec PreKey .............................................................................................................. 607 Displaying the IPsec PreKey ................................................................................................................ 607 Configuring IPsec Phase 1 ................................................................................................................... 607 Configuring IPsec Phase 2 ................................................................................................................... 608 Displaying IPsec information .............................................................................................................. 609 Deleting the IPsec configuration ......................................................................................................... 610 Adding an IPsec security policy ........................................................................................................... 610 Displaying the IPsec security policy database..................................................................................... 611 MANAGING CABLE MODEMS .......................................................................................................................... 612 Displaying cable modem status .......................................................................................................... 612 Displaying cable modem CPE devices ................................................................................................. 619 Displaying cable modems by state ..................................................................................................... 619 Cable modem summary information .................................................................................................. 620 Configuring the cable modem flap list ................................................................................................ 622 Showing the cable modem flap-list .................................................................................................... 624 Showing the cable modem summary ................................................................................................. 625 Displaying the cable modem summary (Release 5.4) ......................................................................... 626

CASA CMTS Displaying the cable modem on downstream channels ..................................................................... 627 Displaying cable modem physical information ................................................................................... 628 Showing the cable modem remote-query........................................................................................... 628 Configuring the remote-query polling interval ................................................................................... 629 Configuring the remote-query loopback interface ............................................................................. 630 Displaying the cable modem remote-query with a specified MAC address........................................ 630 Showing the cable modem remote-query with a specified IP address ............................................... 631 Setting the cable modem flap-list aging interval ................................................................................ 631 Accelerating cable modem registration.............................................................................................. 631 Registering DOCSIS 2.0 bonding modems........................................................................................... 632 Enabling the cable modem flap-list trap (Release 5.2) ....................................................................... 632 Enabling the cable modem flap-list trap (Release 5.4) ....................................................................... 633 Configuring a cable modem deny list ................................................................................................. 633 Enabling PacketCable admission control preempt voice priority........................................................ 633 Setting global QoS bandwidth over upstream and downstream interfaces ....................................... 634 Configuring QoS temporary upstream service flows .......................................................................... 635 Enabling cable DSX authorization ....................................................................................................... 635 Enabling Receive Channel Profile (RCP) fragment support ................................................................. 636 Controlling CMTS upstream power levels (Rel. 6.1 and later) ............................................................ 636 Adjusting modem upstream power levels (Rel. 6.1 and later) ............................................................ 637 Setting the SNR averaging interval ..................................................................................................... 637 Resetting cable modems and clearing cable modem counters .......................................................... 638 Clearing offline cable modems immediately ...................................................................................... 639 Clearing offline cable modems after aging ......................................................................................... 639 Displaying cable modem vendors ....................................................................................................... 640 Displaying vendor-specific information on cable modems ................................................................. 641 Adding and modifying cable modem vendor information .................................................................. 641 Deleting cable modem vendor information ........................................................................................ 642 Displaying vendor OUI information .................................................................................................... 642 Setting the default cable modem vendor ........................................................................................... 643 Displaying cable modem classifiers .................................................................................................... 644 Showing cable modem errors ............................................................................................................. 646 Displaying cable modem MAC information ........................................................................................ 646 Displaying cable modem spoof information ....................................................................................... 647 Displaying cable modem maintenance ranging information ............................................................. 648

CASA CMTS Displaying denied cable modem ......................................................................................................... 649 Displaying the cable modem MAC summary ...................................................................................... 649 Displaying the cable modem status event report ............................................................................... 650 Displaying cable modem quality-of-service (QOS) .............................................................................. 650 Displaying the cable modem docsis-mac summary ............................................................................ 651 Enabling/disabling cable modem host authorization ......................................................................... 652 Displaying the cable host authorization ............................................................................................. 653 SUBSCRIBER MANAGEMENT ........................................................................................................................... 653 CM controls (Rel. 6.0.3 and earlier) .................................................................................................... 653 Default settings .................................................................................................................................. 653 Filters .................................................................................................................................................. 653 Enabling subscriber management ...................................................................................................... 654 Setting the mode for a CM to learn the CPE IP address without DHCP (Rel. 6.0.3 and earlier) .......... 655 Setting maximum IPv4 CPEs behind a CM (Rel. 6.0.3 and earlier) ...................................................... 655 Setting maximum IPv6 CPEs behind a CM (Rel. 6.0.3 and earlier) ...................................................... 656 Resetting IP addresses of all CPEs behind a CM (Rel. 6.0.3 and earlier) ............................................. 656 Using the subscriber management default settings ........................................................................... 656 Displaying the DOCSIS subscriber management defaults ................................................................... 658 Setting a filter rule .............................................................................................................................. 659 Removing all IP and TCP-UDP filters ................................................................................................... 659 Displaying IP filters ............................................................................................................................. 659 Displaying cable modem information (Rel. 6.0.3 and earlier) ............................................................ 660 Displaying the cable modem control table (Rel. 6.0.3 and earlier)..................................................... 660 Displaying CPE information (Rel. 6.0.3 and earlier) ............................................................................ 661 CONFIGURING MPEG COMPLIANT FEATURES ................................................................................................... 661 Setting the PAT insertion interval ....................................................................................................... 661 Setting the PMT insertion interval ...................................................................................................... 662 CONFIGURING DVB-COMPLIANT FEATURES ...................................................................................................... 662 Enabling SI table generation and insertion......................................................................................... 662 Setting the network ID ........................................................................................................................ 664 Setting the channel transport stream ID ............................................................................................ 665 CONFIGURING THE TIME OFFSET TABLE ........................................................................................................... 666 Setting the time zone .......................................................................................................................... 667 Setting the time offset ........................................................................................................................ 667 Setting daylight saving time (US only) ................................................................................................ 668

CASA CMTS CONFIGURING THE DOCSIS EVENT NOTIFICATION POLICY .................................................................................... 668 Enabling DOCSIS cable event reporting .............................................................................................. 669 Configuring event reporting by unique identifier ............................................................................... 669 Displaying the cable event identifiers ................................................................................................. 670 Configure the event reporting flags for DOCSIS event messages ....................................................... 670 Displaying the current priority and flags for cable event logging....................................................... 672 Enabling logging of DOCSIS event messages to a SYSLOG server ....................................................... 672 Configuring the TRAP/INFORM and SYSLOG throttling and limiting attribute ................................... 673 Specifying the throttle interval ........................................................................................................... 673 Specifying the throttle threshold ........................................................................................................ 674 USING THE LOGGING COMMANDS ................................................................................................................... 674 Configuring logging targets and levels ............................................................................................... 675 Excluding user messages from the log file by severity level ............................................................... 676 Displaying the current logging settings .............................................................................................. 677

CASA CMTS

Purpose of the guide

.

Audience

Revision information

CASA CMTS

CASA CMTS

CASA CMTS

CASA CMTS

CASA CMTS

CASA CMTS

Contents

Notation conventions

x y z x y z

CASA CMTS

Slot and port numbering

0 1 2 3 s GigE SFP

CASA CMTS

Slot

0

1

2

3

CASA CMTS

RF interface numbering

CASA CMTS

C10G and C100G redundancy operations

CASA CMTS

Enabling and disabling redundancy on the C10G

CASA CMTS

CASA-CMTS# config CASA-CMTS(config)# ha redundancy [module list]

CASA-CMTS(config)# ha redundancy 0,1,2,5,6,7,8,11,12

CASA-CMTS(config)# ha redundancy

CASA-CMTS(config)# no ha redundancy []

CASA-CMTS(config)# no ha redundancy 2

Reverting to the primary modules after recovery

CASA-CMTS(config)# ha redundancy revert

CASA CMTS

CASA-CMTS(config)# ha redundancy revert 120

CASA-CMTS(config)# no ha redundancy revert

Rebooting of a failed card that is not redundancy-protected

CASA-CMTS(config)#

ha redundancy reboot

CASA-CMTS(config)#

no ha redundancy reboot

Interactively switching between the active and standby

CASA CMTS

CASA-CMTS# ha module protect

CASA-CMTS# ha module revert

Displaying the current high availability settings and log file

CASA-CMTS# show ha configuration ha redundancy revert 30 ha redundancy 0,1,2,3,4,6,7,9,10,11,12,13

Using software auto-recovery

CASA CMTS

CASA-CMTS(config)# ha software auto-recovery

CASA-CMTS(config)#

CASA-C10G# CASA-C10G# CASA-C10G# CASA-C10G#

show show show show

no ha software auto-recovery

envm envm envm envm

[fan | power | temperature] fan [left [0-1]| middle [0-1] | right [0-1]] temperature [module | QAM | SMM | UPS] power

CASA-C10G# show envm PEM A (-48V) Input 1 Input 1 FUSE Input 2 Input 2 FUSE Input 3 Input 4 FUSE Input 4 Input 4 FUSE Temperature

: : : : : : : : :

FAN_Tray

Temperature

LEFT** MIDDLE** RIGHT**

22C/ 71F 23C/ 73F 23C/ 73F

Module 2 6

PEM B (-48V) Input 1 Input 1 FUSE Input 2 Input 2 FUSE Input 3 Input 3 FUSE Input 4 Input 4 FUSE Temperature

Present Good Present Good Present Good Present Good 78 F/26 C DC_A/DC_B -48V/ -48V/ -48V/

Temperature 86F/ 30C 89F/ 32C

0V 0V 0V

Front/Back Fan RPM 2200/2700 1700/2900 2600/2000

: : : : : : : : :

Present Good Present Good Present Good Present Good 80 F/27 C

Switch

Present

ON ON ON

YES YES YES

Status Normal Normal

Type UPS SMM

CASA-C10G(config)#show envm temperature Module Temperature Status 1 87F/ 31C Normal

Type QAM

CASA CMTS

5 6 7 8 9 10 13

78F/ 89F/ 89F/ 102F/ 105F/ 96F/ 71F/

26C 32C 32C 39C 41C 36C 22C

interface qam 1/4 no spectral inversion on annex A modulation 256qam interleave 12 power 450 channel 0 frequency 547000000 no channel 0 shutdown channel 1 frequency 555000000 no channel 1 shutdown channel 2 frequency 563000000 no channel 2 shutdown channel 3 frequency 571000000 no channel 3 shutdown channel 4 frequency 579000000 no channel 4 shutdown channel 5 frequency 587000000 no channel 5 shutdown channel 6 frequency 595000000 no channel 6 shutdown channel 7 frequency 603000000 no channel 7 shutdown no shutdown

Normal Normal Normal Normal Normal Normal Normal

QAM SMM SMM UPS UPS UPS QAM

CASA CMTS

C10G-195(config-if-qam 1/4)#channel 0 frequency 470000000 C10G-195(config-if-qam 1/4)#show interface qam 1/4 interface qam 1/4 no spectral inversion on annex A modulation 256qam interleave 12 power 450 channel 0 frequency 470000000 no channel 0 shutdown channel 1 frequency 478000000 no channel 1 shutdown channel 2 frequency 486000000 no channel 2 shutdown channel 3 frequency 494000000 no channel 3 shutdown channel 4 frequency 579000000 no channel 4 shutdown channel 5 frequency 587000000 no channel 5 shutdown channel 6 frequency 595000000 no channel 6 shutdown channel 7 frequency 603000000 no channel 7 shutdown no shutdown

! C10G-195(config-if-qam 1/4)#

C10G-195(config-if-qam 1/4)#channel 7 frequency 609000000 C10G-195(config-if-qam 1/4)#show interface qam 1/4 interface qam 1/4 no spectral inversion on annex A modulation 256qam interleave 12 power 450 channel 0 frequency 470000000 no channel 0 shutdown channel 1 frequency 478000000 no channel 1 shutdown channel 2 frequency 486000000 no channel 2 shutdown channel 3 frequency 494000000 no channel 3 shutdown channel 4 frequency 585000000 no channel 4 shutdown channel 5 frequency 593000000 no channel 5 shutdown

CASA CMTS

channel 6 frequency 601000000 no channel 6 shutdown channel 7 frequency 609000000 no channel 7 shutdown no shutdown

C1G/C1N features and configuration differences with larger platforms

Completing pre-configuration

CASA CMTS

Using the command line interface

copy run start copy running-config startup-config

CASA-CMTS: alias scm  “show   cable  modem”

Starting the system configuration

CASA CMTS

CASA-CMTS# reset-console

CASA-CMTS>

CASA-CMTS> enable Password: casa CASA-CMTS#

CASA CMTS

CASA-CMTS# show version Running Image: SMM Rel 5.4, Ver 19, Thu Nov 4 09:23:19 EST 2010, (xcheng) Boot device: net Target IP: 192.168.8.232, Host IP: 192.168.8.2 Boot Image: smm.gz.xc54 flash1: SMM Rel 5.4, Ver 19.2, Tue Sep 21 18:12:26 EDT 2010, ( relmgr) flash2: SMM Rel 5.2, Ver 50, Fri Oct 29 12:50:37 EDT 2010, ( moly) CFE Boot: Major 2, Minor 1, Build 4

CASA-CMTS# show system

verbose

CASA-CMTS# show running-config

CASA-CMTS#show running-config verbose

CASA CMTS

(config). CASA-CMTS#config CASA-CMTS(config)#

CASA-CMTS(config)#end CASA-CMTS#

Where:

CASA-CMTS(config)# device location rack5 CASA-CMTS(config)#  device  contact  “Fred  Gamble  at   978-123-4567”

CASA CMTS

CASA-CMTS(config)# secure-console CASA-CMTS(config)# no secure-console

string string

CASA-CMTS(config)# console-password 2b/~2b CASA-CMTS(config)# console-password encrypted 2b/~2b

<

>

CASA-CMTS(config)# console timeout 10 CASA-CMTS(config)#

CASA CMTS

One or more modules are not in running state. You might lose part of your startup-config if you save now. You can wait or use 'copy run start unconditional' to save your config anyway.

CASA-CMTS#copy running-config startup-config

CASA CMTS

CASA-CMTS#config CASA-CMTS(config)#

CASA-CMTS(config)#interface eth 0 CASA-CMTS(conf-if-eth 0)# < >< >

< <

> >

CASA-CMTS(conf-if-eth 0)#ip address 135.2.2.2 255.255.252.0

CASA-CMTS# del startup-config

CASA CMTS

Sample configuration files

hostname CASA-CMTS interface eth 0 ip address 192.168.2.215 255.255.255.0 interface qam 0/0 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface qam 0/1 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface qam 0/2 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface qam 0/3 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface gige 0 ip address 192.168.3.106 255.255.255.0 ip igmp no shutdown route net 0.0.0.0 0 gw 192.168.3.7 igmp client version 2

CASA CMTS

interface upstream 1/0 no shutdown no logical-channel 0 interface upstream 1/1 no shutdown no logical-channel 0 interface upstream 1/2 no shutdown no logical-channel 0 interface upstream 1/3 no shutdown no logical-channel 0 interface upstream 1/4 no shutdown no logical-channel 0 interface upstream 1/5 no shutdown no logical-channel 0 interface upstream 1/6 no shutdown no logical-channel 0 interface upstream 1/7 no shutdown no logical-channel 0

shutdown shutdown shutdown shutdown shutdown shutdown shutdown shutdown

channel-utilization-interval 10 interface ip-bundle 1 ip address 192.168.7.1 255.255.255.0 cable helper-address 192.168.3.7 interface docsis-mac 1 no shutdown ip bundle 1 downstream 1 interface qam 0/0/0 upstream 1 interface upstream 1/0/0

CASA CMTS

hostname CASA-CMTS interface eth 0 ip address 192.168.2.215 255.255.255.0 spectrum rule 35 action modulation frequency channel-width channel-width 3200000 1600000 snmp traphost 192.168.0.196 community public version 2 interface qam 0/0 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface qam 0/1 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface qam 0/2 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface qam 0/3 no shutdown no channel 0 shutdown no channel 1 shutdown no channel 2 shutdown no channel 3 shutdown power 580 interface gige 0 ip address 192.168.3.106 255.255.255.0 ip igmp no shutdown route net 0.0.0.0 0 gw 192.168.3.7

CASA CMTS

interface ip-bundle 1 ip address 192.168.6.1 255.255.255.0 ip address 122.8.74.1 255.255.254.0 secondary cable helper-address 192.168.3.7 service group 1 qam 0/0/0 qam 0/0/1 qam 0/0/2 qam 0/0/3 qam 0/1/0 qam 0/1/1 qam 0/1/2 qam 0/1/3 upstream 1/0.0 upstream 1/1.0 upstream 1/2.0 upstream 1/3.0 upstream 1/4.0 upstream 1/5.0 upstream 1/6.0 upstream 1/7.0 interface docsis-mac 1 no shutdown ip bundle 1 downstream 1 interface qam 0/0/0 downstream 2 interface qam 0/0/1 downstream 3 interface qam 0/0/2 downstream 4 interface qam 0/0/3 downstream 5 interface qam 0/1/0 downstream 6 interface qam 0/1/1 downstream 7 interface qam 0/1/2 downstream 8 interface qam 0/1/3 upstream 1 interface upstream 1/0.0 upstream 2 interface upstream 1/1.0 upstream 3 interface upstream 1/2.0 upstream 4 interface upstream 1/3.0 upstream 5 interface upstream 1/4.0 upstream 6 interface upstream 1/5.0 upstream 7 interface upstream 1/6.0 upstream 8 interface upstream 1/7.0 channel-utilization-interval 10 interface upstream 1/0 no shutdown no logical-channel 0 shutdown interface upstream 1/1 no shutdown no logical-channel 0 shutdown interface upstream 1/2 no shutdown no logical-channel 0 shutdown

CASA CMTS

interface upstream 1/3 no shutdown no logical-channel 0 shutdown interface upstream 1/4 no shutdown no logical-channel 0 shutdown interface upstream 1/5 no shutdown no logical-channel 0 shutdown interface upstream 1/6 no shutdown no logical-channel 0 shutdown interface upstream 1/7 no shutdown no logical-channel 0 shutdown

CASA CMTS

CASA CMTS

Managing the system

CASA CMTS

CASA-CMTS>

CASA-CMTS> enable

CASA-CMTS> enable Password: casa CASA-CMTS#

CASA-CMTS# exit

CASA CMTS

new_password



CASA-CMTS# password mypassword





CASA-CMTS# reset password mypassword

CASA-CMTS(config)# service password-encryption CASA-CMTS#

CASA CMTS

CASA-CMTS#

CASA-CMTS# hostname host_200 host_200#

CASA-CMTS# alias au adduser CASA-CMTS# CASA-CMTS# no alias au CASA-CMTS#

CASA CMTS

CASA-CMTS# show aliases sh alias  sh  “show”

Managing configurations and files

CASA CMTS

One or more modules are not in running state. You might lose part of your startup-config if you save now. You can wait or use 'copy run start unconditional' to save your config anyway.

CASA CMTS

CASA-C10G(config)# copy running-config ftp casa 192.168.8.231 /tmp/config.1 Password: *****

CASA-C10G(config)# copy running-config tftp 192.168.8.231 /tmp/config.1

CASA CMTS

CASA-C10G(config)# copy ftp casa 192.168.8.192 startup-config fdsk2 Password: ***** CASA-C10G(config)# copy ftp casa 192.168.8.192 startup-config module 6 nvram CASA-C10G(config)# copy ftp casa 192.168.8.192 startup-config nvram

CASA CMTS

CASA-C10G(config)# copy tftp 192.168.8.192 startup-config fdsk2 /tmp/config.1 CASA-C10G(config)# copy tftp casa 192.168.8.192 startup-config module 6 nvram CASA-C10G(config)# copy tftp casa 192.168.8.192 startup-config nvram

CASA CMTS

CASA-C10G(config)# copy fdsk2 startup-config ftp casa 192.168.8.192 /tmp Password: ***** CASA-C10G(config)# copy fdsk2 startup-config tftp 192.168.8.192 /tmp/startup-config CASA-C10G(config)# copy fdsk2 startup-config fdsk2 startup-config.backup

CASA CMTS

CASA-C10G> md5 checksum filename

CASA-C10G> total 2079 -rw-r--r--rw-rw-rw-rw-r--r--rw-r--r--rw-r--r-CASA-C10G>

dir fdsk2 1 1 1 1 1

root root root root root

root 17538 Nov 4 root 23822 Oct 5 root 1035812 Nov 4 root 1048634 Nov 3 root 1209 Oct 28

13:19 16:04 13:30 15:46 15:24

cdb.log docsislogfile logfile logfile.old reboot_log

CASA CMTS

CASA-C10G(config-if-gige 6/1)# show this interface gige 6/1 ipv6 address 1000::192/64 mpls mtu 0 auto negotiate no shutdown ip router isis EDGE-IPv6 ipv6 router isis EDGE-IPv6 isis network point-to-point isis circuit-type level-2-only CASA-C10G(config-if-gige 6/1)#

Managing NVRAM Files

CASA CMTS

CASA-CMTS# dir Total 9 -rw—r—r-1 root 1 root 8455 Aug 7 13:44 startup-config CASA-CMTS#

CASA-CMTS# remove startup-config CASA-CMTS# del startup-config

Where:

CASA CMTS

CASA-CMTS# copy nvram startup-config tftp 192.168.2.39 startup-config-Casa CASA-CMTS#

Updating Casa CMTS software

User management and security control

CASA CMTS

Where:

CASA CMTS

CASA-CMTS(config)#privilege configure all level 2 “interface docsis-mac”

CASA-CMTS(config)# privilege exec all level 0 "clear"

CASA-CMTS(config)# privilege exec level 2 "clear cable modem reset" CASA-CMTS(config)# privilege exec all level 2 "ping"

CASA-CMTS# show ssh server SSH Server Enabled: version 2, port 22

CASA-CMTS# show ssh hostkey fingerprint rsa 2048 fe:61:45:6b:48:3f:9e:19:f3:ce:5d:c8:f6:26:9f:a2

CASA CMTS

CASA-CMTS# show ssh hostkey dsa ---- BEGIN SSH2 PUBLIC KEY ---Comment: "1024-bit DSA, converted from OpenSSH by root@C3200_155" AAAAB3NzaC1kc3MAAACBAOFVGDGO85X4Ww4fZyazYXRPnOzj0/0 mMp5FLc7L5ka+W6ksOK 45BSrbVwb4Fk2oCyUJFHUgnfFpSKxSdgVLCeT8VfOSyaLxnLZW7 r2PnLIJnb4ft+sPtBYQ Tf17uIJ/gE+o4AdqAq3KibUOlf9GyxzF8sVr8LYrsiENltaBLuD dAAAAFQDWg6//lFi6BI KUqaC7QjFsc6UXfwAAAIAjgo4/yRUASQi/sk8jL1wjL+kpeBoKi qMtcsT/6MeTyxfequGf TybeNxiI+YXI3xPWQKnYFEFr44EBj0pHXBe09hyHoHIHRFRYB55 JdGJDqk57DXiAS5yFFT NXF2Griv5mPFvuwA2hnHOVJBucrYLfDZL3+YgKBkov65FyYtssm AAAAIEAzhzwHRxVsU+v wgWdTxLnDQEi6//U82ywJdQjVAK6q+daIarwj5I1YIzNFks/cLR j0ZaBSkBtxoqrjNKdXM nQFre0rbbAknFWk2fnt9mrisFKAe/T9O7Y72lqcd5reB54/Uioz E1+WA5+K7oRcdaNKF8V ph7p/2xn7ZeUxQ35ip0= ---- END SSH2 PUBLIC KEY ---CASA-CMTS# show ssh hostkey dsa ---- BEGIN SSH2 PUBLIC KEY ---Comment: "2048-bit RSA, converted from OpenSSH by root@C3200_155" AAAAB3NzaC1yc2EAAAABIwAAAQEArfdT9vRF5UcDc7fyR2Hgt5R xDHqAsIV5AuFxZxZti8 nAdlmcu6pObu1daGQCYRXUQCWHXuy9Ygi1c2tYRMzTCP3I94hC3 ha4RaWZT2MpjfyL+5ml 5NlKX7lBz3yhLQaeHVVkMTQyVMB8kIDABykkKP3v44BMCvbWYdK eA6TbjjADneovdbmdHX tix7XQHDZPhEjYp9PD6tTbCOylp7zzjAcNzZGNG29hH7NECCaS7 jaBEIhe4qPKCTYIg6+E 2AY7koxmxcU8guXV4Zgvku8BJqDyje59+FYZF8N3jWAPIsR1Cp1 Au3ofgtBk2yjQtFcSux SWzCDTWEH+WdeZfUmaxw== ---- END SSH2 PUBLIC KEY ---C3200_155# CASA-CMTS# show ssh hostkey fingerprint 2048 ee:b7:aa:9f:c0:6c:69:5e:e0:96:ea:36:ff:d5:e9:d4

CASA CMTS

CASA-CMTS# ssh start [port ]

CASA-CMTS# ssh stop SSH server stopped.

CASA-CMTS# ssh gen-hostkey {dsa | rsa}

CASA-CMTS(config)# ssh enable CASA-CMTS(config)# no ssh enable

CASA CMTS

user-name

password password

CASA-CMTS#  adduser  operator  privilege  9… Enter new password: private Re-enter new password: private CASA-CMTS#

CASA-CMTS# show user User Level ----------------------------root 15 metro 15 Supp0rt 10 adrian 10 noct 15 CASA-CMTS# show user current USER TTY TYPE FROM SINCE --------------------------------------------------root pts/0 ssh 135.244.224.74 Sun Oct 31 13:47:57 2010 henk pts/1 ssh 135.85.12.131 Sun Oct 31 13:57:57 2010

CASA CMTS

CASA-CMTS# user password operator Enter new password: public Re-enter new password: public CASA-CMTS#

username



CASA-CMTS# deluser operator CASA-CMTS# .

CASA CMTS

1

CASA-CMTS# show user current USER TTY TYPE FROM SINCE ---------------------------------------------------------------------root pts/1 telnet 192.168.2.38 Mon Aug 2 21:28:50 2010

CASA-CMTS# deluser root session pts/1 Connection closed by foreign host. [user@gollum]$

CASA-CMTS# config CASA-CMTS(config)# telnet port 23 CASA-CMTS (config)# show telnet port telnet port 23

CASA CMTS

CASA-CMTS# config CASA-CMTS(config)# line vty 12

CASA-CMTS# config CASA-CMTS(config)# telnet timeout 60 CASA-CMTS# config CASA-CMTS(config)# no telnet timeout

CASA CMTS

CASA-CMTS# system reboot reason “Use  new  release   5.4.19.9” CASA-CMTS#system reboot reason test at 22:00 11 December Broadcast Message from root@CASA-CMTS (/dev/pts/0) at 11:40 .. System reboot scheduled for Fri Dec 11 22:00:00 2009 Broadcast Message from root@CASA-CMTS (/dev/pts/0) at 11:40 ..

CASA CMTS

System reboot reason: test

CASA-CMTS#system reboot cancel Broadcast Message from root@CASA-CMTS (/dev/pts/0) at 10:00 *** ---SHUTDOWN ABORTED--***

CASA-CMTS#show system reboot System reboot scheduled for Fri Dec 11 22:00:00 2010 (in 24 minutes, 53 seconds) Reboot reason: test Remind: 1 minute before system reboot CASA-CMTS#

CASA-CMTS(config)#system reboot confirm

CASA CMTS

CASA-CMTS#system reboot System configuration has been modified. Save [yes/no]? yes Proceed with reload? {confirm | no} [Enter]

CASA-CMTS# show bootdev System boot device is: flash1 CASA-CMTS#

CASA-CMTS# show system Product: C2200, Module: SMM Major rev 1, Minor rev 1 serial_no = SV03B17S0016 CFE version 2.1.3 System Time: Sun Apr 12 20:32:40 EST 2009

CASA CMTS

System Uptime: 0 d, 0 h, 14 m, 49 s 128MHz T1 Clock Module 1 UPS Running (8 ports, 2 phy chans/port, 1 log chans/phy chan, scdma map 00) Major rev 3, Minor rev 0 serial_no = UV30B89S0003 CFE version 2.1.5 Module 2 QAM Running (4 ports, 4 channels/port, 1 banks/port, docsis enabled) Major rev 4, Minor rev 1 serial_no = QV46B89S0143 CFE version 2.1.3

1

CASA-CMTS#show version Running Image: SMM Rel 5.2, Ver 28, Wed Jun 24 16:09:44 EDT 2009, (moly) Boot device: flash2 flash1: SMM Rel 5.2, Ver 26B, Fri Jun 5 08:27:11 EDT 2009, ( moly) flash2: SMM Rel 5.2, Ver 28, Wed Jun 24 16:12:39 EDT 2009, ( moly) CFE Boot: Major 2, Minor 1, Build 3

CASA CMTS

CASA-CMTS(config)# system clock 071621082004 Fri Jul 16 21:08:00 UTC 2004

CASA-CMTS# show clock Fri Jul 16 21:08:06 UTC 2004 CASA-CMTS#

CASA-CMTS(config)# system timezone America/New_York

CASA-CMTS(config)# show timezone Timezone set to "America/New_York", offset from UTC is -0400

CASA-CMTS(config)# show timezone list

CASA CMTS

CASA-CMTS(config)# ntp server 192.168.4.200 CASA-CMTS(config)# ntp scheck Restarting  NTP  server… Stopping NTP server: ntpd Starting NTP server: ntpd. CASA-CMTS (config)# CASA-CMTS(config)# ntp sync 192.168.4.200 1 Nov 10:06:00 ntpdate[10661]:step time server 192.168.4.200 offset 0.075592 Restarting  NTP  server… Stopping NTP server: ntpd Starting NTP server: ntpd. CASA-CMTS(config)# ntp source-interface loopback 5

CASA CMTS

CASA-CMTS(config)# show ntp status

Example C3000-230(config# show ntp status remote

refid

st t when poll reach

delay

offset

jitter

============================================================================== 203.248.240.140 .INIT.

16 -

- 1024

0

0.000

0.000

0.000

CASA CMTS

CASA-CMTS(config)# system rate limit broadcast 500

CASA-CMTS(config)# system rate limit broadcast 0

CASA-CMTS(config)# ntp source-interface loopback 4

CASA CMTS

CASA-CMTS(config)# route net 193.100.1.0 24 gw 192.168.2.177 CASA-CMTS(config)# CASA-CMTS(config)# no route net 193.100.1.0 24 gw 192.168.0.177

CASA-CMTS(config)# route host 192.168.10.1 gw 192.168.2.177 CASA-CMTS(config)# no route host 192.168.10.1 gw 192.168.2.177

CASA CMTS

CASA-CMTS(config)# route net 2001.1234.1234.1234::::/64 gw 2001:1234::0 CASA-CMTS(config)#

CASA-CMTS(config)#show route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.3.0 * 255.255.255.0 U 0 0 0 gige0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 10.170.1.0 * 255.255.255.0 U 0 0 0 dmac1 10.121.0.0 192.168.0.135 255.255.0.0 UG 0 0 0 eth0 default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0

CASA CMTS

C3000-230(config)#show ip interface brief

Example: show ip interface brief C3000-230(config)#show ip interface brief Interface eth 0 loopback0 loopback0 gige 0 gige 0 gige 3 gige 3 vlan 34 vlan 34 vlan 35 vlan 36 vlan 37 vlan 2322 ipbundle1 ipbundle1.1 ipbundle1.1 ipbundle2 ipbundle2

IP-Address 192.168.8.230 88.88.88.230 128:238:238:238::230 192.168.3.230 3000::230 33.33.33.230 4000:238:238:238::230 34.34.34.230 3000:238:238:238::230 35.35.35.230 36.36.36.230 37.37.37.230 12.232.100.230 10.230.1.1 10.10.20.1 10.188.1.1 10.230.20.1 2000:230:1::1

CASA-CMTS# show alarm

Admin Status up up up up up up up up up up up up up up up up up up

Link Status up up up up up down down down down down down down down up up up down down

CASA CMTS

CASA-CMTS# show log [Tue Oct 27 23:53:26 2009]-AL-CLI-1: User user logged in from 70.168.1.63 [Tue Oct 27 23:53:25 2009]-AL-CLI-1: User root logged in from 192.168.3.32 [Tue Oct 27 23:46:39 2009]-AL-SYS-1: Module 0 (QAM), is up [Tue Oct 27 23:46:15 2009]-AL-SYS-1: Module 1 (UPS), is up [Tue Oct 27 23:45:57 2009]-AL-CLI-1: User root logged in from 192.168.5.169 [Tue Oct 27 23:45:19 2009]-AL-SYS-1: Module 1 (UPS), in boot state [Tue Oct 27 23:45:18 2009]-AL-SYS-1: Module 0 (QAM), in boot state

[Wed Oct 28 07:45:09 2009]-AL-CLI-1: Reboot reason: Unspecified [Wed Oct 28 07:45:09 2009]-AL-CLI-1: User root Rebooting system

CASA-CMTS(config)# logging source-interface loopback

CASA CMTS

CASA-CMTS(config)# lawful-intercept tid stream-id CASA_CMTS (config)# lawful-intercept sourceinterface loopback 0

CASA-CMTS# show rstp bridge

CASA CMTS

CASA-CMTS# show rstp port []

CASA-CMTS# show arp Address Age Hardware Addr Interface

State

Type

192.168.2.38 00:00:00 00c0.9f24.bfee dynamic ARPA eth 0 192.168.2.39 00:19:03 000c.f1a6.36e8 dynamic ARPA eth 0 192.168.2.114 00:14:18 000d.5663.d756 dynamic ARPA eth 0 192.168.2.238 00:10:00 0050.c231.c013 static ARPA eth 0 192.168.3.6 00:10:00 0009.5bbd.b87e dynamic ARPA Gige 0 192.168.3.131 00:00:00 0050.c231.c03b static ARPA Gige 0 192.169.4.4 00:18:19 0050.c231.c03f static ARPA CATV-MAC 1 192.169.4.120 00:00:48 0011.1ac8.326e dynamic ARPA CATV-MAC 1 192.169.4.121 00:00:51 0016.b560.aef8 dynamic ARPA CATV-MAC 1

CASA CMTS

CASA-CMTS(config)# arp request-interval 2000

CASA-CMTS(config)# cable arp filter 5 2

CASA CMTS

CASA-CMTS# clear arp-cache all CASA-CMTS# clear arp-cache 192.168.2.177 CASA(config)# clear arp-cache 192.*.*.* CASA(config)# clear arp-cache 10.223.*.*

CASA-CMTS# show arp request-interval

CASA CMTS

CASA-CMTS(config)# arp timeout-cm-reset

CASA-CMTS(config)# no arp timeout-cm-reset

CASA-CMTS# show ipv6 route | Output modifiers xxxx:xxxx:...:xxxx xxxx:xxxx:...:xxxx/mask_len bgp show ipv6 route bgp connected show ipv6 route connected isis show ipv6 route isis kernel show ipv6 route kernel ospf show ipv6 route ospf rip show ipv6 route rip static show ipv6 route static supernets-only supernets-only

CASA-CMTS# show router-advertisement

CASA CMTS

CASA-CMTS# show route6

CASA-CMTS# show arp timeout-cm-reset

CASA-CMTS# show cpuinfo

CASA-CMTS# show cpuinfo module 0 Module 0: cpu model SiByte SB1 V0.3 FPU V0.3 BogoMIPS 532.48 microsecond timers yes tlb_entries 64 11:01pm up 20 min, 0 users, load average: 0.13, 0.07, 0.01

CASA CMTS

44 processes: 43 sleeping, 1 running, 0 zombie, 0 stopped CPU states: 2.3% user, 1.4% system, 0.0% nice, 96.3% idle Mem: 245352K total, 192896K used, 52456K free, 500K buffers CASA-CMTS#

Example: show cpuinfo all CASA-CMTS# show cpuinfo all SMM: cpu model SiByte SB1 V0.3 FPU V0.3 BogoMIPS 265.42 microsecond timers yes tlb_entries 64 5:28pm up 1:24, 1 user, load average: 0.00, 0.00, 0.00 106 processes: 104 sleeping, 1 running, 1 zombie, 0 stopped CPU states: 0.1% user, 0.7% system, 0.0% nice, 99.2% idle Mem: 231684K total, 137320K used, 94364K free, 1004K buffers Module 0: cpu model SiByte SB1 V0.3 FPU V0.3 BogoMIPS 532.48 microsecond timers yes tlb_entries 64 5:28pm up 1:24, 0 users, load average: 0.02, 0.04, 0.00 44 processes: 43 sleeping, 1 running, 0 zombie, 0 stopped CPU states: 2.2% user, 0.9% system, 0.0% nice, 97.0% idle Mem: 245352K total, 192896K used, 52456K free, 500K buffers Module 1: cpu model SiByte SB1 V0.3 FPU V0.3 BogoMIPS 265.42 microsecond timers yes tlb_entries 64 5:28pm up 1:24, 0 users, load average: 0.21, 0.31, 0.28 45 processes: 44 sleeping, 1 running, 0 zombie, 0 stopped CPU states: 4.5% user, 2.2% system, 0.0% nice, 93.3% idle Mem: 245356K total, 140044K used, 105312K free, 504K buffers

CASA CMTS

CASA-CMTS# show cpu-process

Example: show cpu-process C3000-230# show cpu-process UID root root root root root root root root root root root root root

PID 1 2 3 4 5 6 7 8 9 10 11 12 86

PPID 0 0 2 2 2 2 2 2 2 2 2 2 2

LWP 1 2 3 4 5 6 7 8 9 10 11 12 86

C NLWP STIME TTY 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ? 0 1 Nov15 ?

TIME 00:00:15 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:01

CMD init [3] [kthreadd] [ksoftirqd/0] [events/0] [khelper] [kblockd/0] [kseriod] [casa_help] [pdflush] [pdflush] [kswapd0] [aio/0]

CASA-CMTS# show cpu-memory process-list all

Example: show cpu-memory process-list module 1 C3000-230#show cpu-memory process-list module 1 Module 1 CPU and Memory information: COMMAND PID USER STIME init 1 root 11:59 kthreadd 2 root 11:59 migration/0 3 root 11:59 ksoftirqd/0 4 root 11:59 migration/1 5 root 11:59 ksoftirqd/1 6 root 11:59 migration/2 7 root 11:59

TIME %CPU %MEM 00:00:11 0.6 0.0 00:00:00 0.0 0.0 00:00:00 0.0 0.0 00:00:00 0.0 0.0 00:00:00 0.0 0.0 00:00:00 0.0 0.0 00:00:00 0.0 0.0

CASA CMTS

ksoftirqd/2 migration/3 ksoftirqd/3 migration/4 ksoftirqd/4 migration/5 ksoftirqd/5 migration/6 ksoftirqd/6 migration/7 ksoftirqd/7 migration/8 ksoftirqd/8 migration/9

8 9 10 11 12 13 14 15 16 17 18 19 20 21

root root root root root root root root root root root root root root

11:59 11:59 11:59 11:59 11:59 11:59 11:59 11:59 11:59 11:59 11:59 11:59 11:59 11:59

00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00 00:00:00

CASA-CMTS# show meminfo

CASA-CMTS# show meminfo module 0 Module 0: MemTotal: 245352 kB MemFree : 52672 kB CASA-CMTS#

0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0

0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0

CASA CMTS

CASA-CMTS# show meminfo all SMM: MemTotal: 231684 kB MemFree: 94524 kB Module 0: MemTotal: 245352 kB MemFree : 52672 kB Module 1: MemTotal: 245356 kB MemFree : 105528 kB CASA-CMTS#

CASA-CMTS(config)#show controller

Example: show controller C3000-230#show controller Upstream module information: Interface upstream 4/0.0/0 information: IfIndex : 5000256 Admin status: UP Operating status: UP Frequency: 20000000 Hz Channel Width: 3200000 Hz Power Level: 0 Modulation profile 2 SNR: 28.2 Statistics: Received 12 broadcasts, 6 multicasts, 340 unicasts 0 discards, 0 errors, 0 unknown protocol

CASA CMTS

1247 Unerroreds, 1 Correcteds, 0 Uncorrectables Req Mslots 337935795, Used Req Mslots 1089 Init Mtn Mslots 3805323, Used Init Mtn Mslots 0 Total Mslots 341756450, Ucast Granted Mslots 15268 Downstream module information: Interface QAM 0/0 Admin Status: UP Power level: 450 Channel 0: IfIndex : 3000000 Admin Status : UP Operating Status : UP Frequency : 549000000 Channel Width : 6000000 Modulation : 256QAM Annex: : B Statistics: Broadcast packets : 8064 Multicast packets : 0 Unicast packets : 59 UCD counts : 5363 MAP counts : 2180539 Interface docsis-mac 1 statistics Ifindex: 2000001 Administrated status: UP Operation status: UP Mac address: 0017.1080.5e40 DSA Request : 0/ups; 0/ds DSA Response : 0/ups; 0/ds DSA Acknowledgements : 0/ups; 0/ds DSA Success : 0/ups; 0/ds DSA Fail : 0/ups; 0/ds DSC Request : 0/ups; 0/ds DSC Response : 0/ups; 0/ds DSC Acknowledgements : 0/ups; 0/ds DSC Success : 0/ups; 0/ds DSC Fail : 0/ups; 0/ds DSD Request : 0/ups; 0/ds DSD Response : 0/ups; 0/ds DSD Success : 0/ups; 0/ds DSD Fail : 0/ups; 0/ds DCC Request : 0/ups; 0/ds DCC Response : 0/ups; 0/ds DCC Acknowledgements : 0/ups; 0/ds DCC Success : 0/ups; 0/ds DCC Fail : 0/ups; 0/ds DCC RSP Depart : 0/ups; 0/ds DCC RSP Arrive : 0/ups; 0/ds DBC Request : 0/ups; 0/ds

CASA CMTS

DBC Response : 0/ups; DBC Acknowledgements : 0/ups; DBC Success : 0/ups; DBC Fail : 0/ups; DBC Partial Service : 0/ups; Last clearing of interface stat: never Interface gige 11 information: IfIndex: 1000083 interface status Administratively DOWN link status DOWN auto-negotiation Enabled interface speed 1000000000 duplex status Full mac address 0017.1000.5e4d Statistics: IfInOctets 0 IfInUcastPkts 0 IfInNUcastPkts 0 IfInNUcastDiscards 0 IfInDiscards 0 IfInErrors 0 IfInUnknownProtos 0 IfOutOctets 0 IfOutUcastPkts 0 IfOutNUcastPkts 0 IfOutErrors 0 IfOutNUcastDiscards 0 IfOutDiscards 0 IpForwDatagrams 0 IpInReceives 0 IpInDiscards 0 v6IfInReceives 0 v6IfInDiscards 0 v6IfInErrors 0 v6IfOutForwDatagrams 0 v6IfOutDiscards 0 Last clearing of interface stat: never SMM xgig interface information: eth interface information: Interface eth 0 information: IfIndex: 1 interface status UP interface speed 100000000 mac address 0017.1000.5e40 Statistics: IfInOctets 28077350 IfInUcastPkts 57667 IfInDiscards 0 IfInErrors 0

0/ds 0/ds 0/ds 0/ds 0/ds

CASA CMTS

IfOutOctets IfOutUcastPkts IfOutErrors IfOutDiscards C3000-230#

2285988 49326 0 0

CASA-CMTS(config)# monitor keepalive

CASA-CMTS(config)# no monitor keepalive

CASA-CMTS(config)# monitor gige CASA-CMTS(config)# no monitor gige

CASA CMTS

CASA-CMTS(config)# clear interface gige 0 stat CASA-CMTS(config)#

CASA-CMTS(config)# show monitor Monitor GIG-E activity : Monitor Keepalive : Monitor Daemon :

Disabled Disabled Enabled

CASA CMTS

CASA-CMTS(config)#auto-reboot monitor 192.168.2.177 30

CASA-CMTS# ping 192.168.8.113 PING 192.168.8.113 (192.168.8.113) 56(84) bytes of data. 64 bytes from 192.168.8.113: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.8.113: icmp_seq=2 ttl=64 time=0.067 ms 64 bytes from 192.168.8.113: icmp_seq=3 ttl=64 time=0.082 ms --- 192.168.8.113 ping 3 packets transmitted, time 2000ms rtt min/avg/max/mdev = CASA-CMTS(conf-if-vlan

statistics --3 received, 0% packet loss, 0.067/0.083/0.102/0.017 ms 6/10)#

CASA-CMTS(conf-if-vlan 6/10)# ping6 2001:0db8:85a3:0000:0000:8a2e:0370:7334

CASA CMTS

CASA-CMTS#ping "-I 10.248.1.1 192.168.3.8" PING 192.168.3.8 (192.168.3.8) from 10.248.1.1 : 56(84) bytes of data. 64 bytes from 192.168.3.8: icmp_seq=1 ttl=64 time=0.357 ms 64 bytes from 192.168.3.8: icmp_seq=2 ttl=64 time=0.372 ms 64 bytes from 192.168.3.8: icmp_seq=3 ttl=64 time=0.361 ms

CASA CMTS

CASA CMTS

C10G-CMTS# traceroute 192.168.3.195 ***** Type Ctrl-C to exit ***** traceroute to 192.168.3.195 (192.168.3.195), 30 hops max, 40 byte pac 1 192.168.10.110 (192.168.10.110) 2.111 ms 2.228 ms 2.147 ms 2 192.168.20.108 (192.168.20.108) 1.241 ms 0.904 ms 0.948 ms 3 192.168.3.195 (192.168.3.195) 1.165 ms 1.218 ms 1.150 ms C10G-CMTS# traceroute help Usage: traceroute [ -dFInrvx ] [ -f first_ttl ] [ -g gateway ] [ -i iface ] [ -m max_ttl ] [ -p port ] [ -q nqueries ] [ -s src_addr ] [ -t tos ] [ -w waittime ] [ -z pausemsecs ] host [ packetlen ] The entire argument list must be with quotation marks Example: traceroute "pluto" C10G-CMTS# traceroute  “192.168.3.192  1500” ***** Type Ctrl-C to exit ***** traceroute to 192.168.8.230 (192.168.8.230), 30 hops

CASA CMTS

max, 1500 byte packets 1 192.168.8.230 (192.168.8.230) 0.748 ms

1.624 ms

0.943 ms

traceroute to verizon.net (206.46.232.39), 30 hops max, 40 byte packets 1 192.168.2.1 (192.168.2.1) 0.564 ms 0.438 ms 0.402 ms 2 192.168.1.1 (192.168.1.1) 1.724 ms 1.482 ms 1.334 ms 3 192.168.0.1 (192.168.0.1) 3.573 ms 3.308 ms 3.400 ms 4 209.101.35.209 (209.101.35.209) 4.334 ms * 4.179 ms 5 208-41-205-1.client.dsl.net (208.41.205.1) 20.577 ms 16.912 ms 19.954 ms 6 ge-2-2-0.c00.nyc.megapath.net (155.229.123.121) 19.863 ms 17.526 ms 19.568 ms 7 ge-6-5.car1.NewYork1.Level3.net (209.246.126.1) 19.946 ms 17.224 ms 19.897 ms 8 vlan69.csw1.NewYork1.Level3.net (4.68.16.62) 19.893 ms 17.967 ms 19.767 ms 9 ae-64-64.ebr4.NewYork1.Level3.net (4.69.134.113) 24.904 ms 22.647 ms * 10 ae-6-6.ebr2.NewYork2.Level3.net (4.69.141.22) 19.224 ms 17.346 ms 19.626 ms 11 ae-2-52.edge2.NewYork2.Level3.net (4.69.138.227) 23.098 ms 17.541 ms ae1-51.edge2.NewYork2.Level3.net (4.69.138.195) 25.399 ms 12 0.ge-2-0-0.BR3.NYC4.ALTER.NET (204.255.173.53) 17.668 ms mci-level3xe.newyork2.Level3.net (4.68.110.234) 17.970 ms mci-level3xe.newyork2.Level3.net (4.68.110.106) 57.640 ms 13 0.xe-0-1-3.XL3.NYC4.ALTER.NET (152.63.17.58) 18.088 ms 0.xe-5-03.XL3.NYC4.ALTER.NET (152.63.18.6) 17.976 ms 0.xe-5-1-3.XL3.NYC4.ALTER.NET (152.63.16.182) 19.120 ms 14 0.ge-7-2-0.XL3.DFW7.ALTER.NET (152.63.0.34) 102.254 ms 101.897 ms 104.069 ms 15 POS7-0.GW2.DFW13.ALTER.NET (152.63.103.229) 103.922 ms POS60.GW2.DFW13.ALTER.NET (152.63.103.225) 102.292 ms 101.520 ms 16 verizon-gw.customer.alter.net (63.65.122.26) 104.015 ms 102.131 ms 103.928 ms 17 po121.ctn-core1.vzlink.com (206.46.225.18) 114.777 ms 101.656 ms 103.760 ms 18 206.46.228.130 (206.46.228.130) 104.236 ms 101.775 ms 104.338 ms 19 206.46.232.34 (206.46.232.34) 103.508 ms 102.530 ms 103.747 ms

CASA CMTS

CASA-CMTS(config)# cable icmp filter 100 2

CASA-CMTS(config)# cable dhcp filter 100 2

CASA-C3000(config)#show cable filter runningconfig cable arp filter 8 2 cable dhcp filter 100 2 cable icmp filter 0 2 cable igmp filter 4 2 CASA-C3000(config)#

CASA CMTS

CMTS(config)# channel-utilization-interval 100

CMTS(config)# show docsis channel utilization

Example: Display channel utilization Downstream Operational Utilization Online Secondary Channel Slot/Port/Channel Status Percentage Modems Modems Description ----------------------------------------------------------------------------0/0/0 (549000000 Hz) down 0 0 0 0/0/1 (555000000 Hz) down 0 0 0 0/0/2 (561000000 Hz) down 0 0 0 0/0/3 (567000000 Hz) down 0 0 0 0/1/0 (549000000 Hz) down 0 0 0 0/1/1 (555000000 Hz) down 0 0 0 0/1/2 (561000000 Hz) down 0 0 0 0/1/3 (567000000 Hz) down 0 0 0 0/2/0 (549000000 Hz) down 0 0 0 0/2/1 (555000000 Hz) down 0 0 0 0/2/2 (561000000 Hz) down 0 0 0 0/2/3 (567000000 Hz) down 0 0 0 0/3/0 (549000000 Hz) down 0 0 0 0/3/1 (555000000 Hz) down 0 0 0 0/3/2 (561000000 Hz) down 0 0 0 0/3/3 (567000000 Hz) down 0 0 0 1/0/0 (549000000 Hz) down 0 0 0

CASA CMTS

1/0/1 1/0/2 1/0/3 1/1/0 1/1/1 1/1/2 1/1/3 1/2/0 1/2/1 1/2/2 1/2/3 1/3/0 1/3/1 1/3/2 1/3/3 2/0/0 2/0/1 2/0/2 2/0/3 2/1/0 2/1/1 2/1/2 2/1/3 2/2/0 2/2/1 2/2/2 2/2/3 2/3/0 2/3/1 2/3/2 2/3/3 3/0.0 3/0.1 3/1.0 3/1.1 3/2.0 3/2.1 3/3.0 3/3.1 3/4.0 3/4.1 3/5.0 3/5.1 3/6.0 3/6.1 3/7.0 3/7.1 4/0.0 4/0.1 4/1.0 4/1.1 4/2.0 4/2.1 4/3.0 4/3.1 4/4.0 4/4.1 4/5.0 4/5.1 4/6.0 4/6.1 4/7.0

(555000000 Hz) (561000000 Hz) (567000000 Hz) (549000000 Hz) (555000000 Hz) (561000000 Hz) (567000000 Hz) (549000000 Hz) (555000000 Hz) (561000000 Hz) (567000000 Hz) (549000000 Hz) (555000000 Hz) (561000000 Hz) (567000000 Hz) (549000000 Hz) (555000000 Hz) (561000000 Hz) (567000000 Hz) (549000000 Hz) (555000000 Hz) (561000000 Hz) (567000000 Hz) (549000000 Hz) (555000000 Hz) (561000000 Hz) (567000000 Hz) (549000000 Hz) (555000000 Hz) (561000000 Hz) (567000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz) (20000000 Hz)

down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down down

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

CASA CMTS

4/7.1 5/0.0 5/0.1 5/1.0 5/1.1 5/2.0 5/2.1 5/3.0 5/3.1 5/4.0 5/4.1 5/5.0 5/5.1 5/6.0 5/6.1 5/7.0 5/7.1

(20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000 (20000000

Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz) Hz)

down down down down down down down down down down down down down down down down down

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

CMTS(config)# show docsis upstream channel utilization

Example: Display upstream channel utilization Upstream Operational Utilization Online Secondary Channel Slot/Port.Channel Status Percentage Modems Modems Description ------------------------------------------------------------------------------2/0.0 (18000000 Hz) up 0 1 4 Certification 2/0.1 (20000000 Hz) down 0 0 0 2/1.0 (25000000 Hz) up 0 8 3 2/1.1 (20000000 Hz) down 0 0 0 2/2.0 (32000000 Hz) up 2 7 4 2/2.1 (20000000 Hz) down 0 0 0 2/3.0 (11000000 Hz) up 0 4 3 2/3.1 (20000000 Hz) down 0 0 0 2/4.0 (16000000 Hz) up 0 0 0 2/4.1 (20000000 Hz) down 0 0 0 2/5.0 (20000000 Hz) up 0 0 0 2/5.1 (20000000 Hz) down 0 0 0 2/6.0 ( 8000000 Hz) down 0 0 0 docsis 2/6.1 (20000000 Hz) down 0 0 0 2/7.0 (32000000 Hz) down 0 0 0 2/7.1 (20000000 Hz) down 0 0 0

CASA CMTS

4/0.0 4/0.1 4/1.0 4/1.1

(32600000 (34200000 (35800000 (37400000

Hz) Hz) Hz) Hz)

up up up up

0 0 0 0

0 0 0 0

0 0 0 0

CMTS(config)# show docsis downstream channel utilization

Example: Display downstream channel utilization Downstream Operational Utilization Online Secondary Channel Slot/Port/Channel Status Percentage Modems Modems Description ----------------------------------------------------------------------------0/0/0 (525000000 Hz) up 0 0 5 testing 0/0/1 (531000000 Hz) up 0 0 5 0/0/2 (537000000 Hz) up 0 0 5 0/0/3 (543000000 Hz) up 0 0 5 0/1/0 (465000000 Hz) up 0 0 0 0/1/1 (471000000 Hz) up 0 0 0 0/1/2 (477000000 Hz) up 0 0 0 0/1/3 (483000000 Hz) up 0 0 0 0/2/0 ( 47000000 Hz) down 0 0 0 Certification 0/2/1 ( 53000000 Hz) down 0 0 0 Rotterdam 5 0/2/2 ( 59000000 Hz) down 0 0 0 0/2/3 ( 65000000 Hz) down 0 0 0 0/3/0 (549000000 Hz) up 0 0 6 0/3/1 (555000000 Hz) up 4 20 0 0/3/2 (561000000 Hz) up 0 0 6 0/3/3 (567000000 Hz) up 0 0 6 1/0/0 (129000000 Hz) down 0 0 0 1/0/1 (135000000 Hz) up 0 0 0 1/0/2 (141000000 Hz) up 0 0 0 1/0/3 (147000000 Hz) up 0 0 0 1/1/0 (549000000 Hz) down 0 0 0 1/1/1 (555000000 Hz) down 0 0 0 1/1/2 (561000000 Hz) down 0 0 0 1/1/3 (567000000 Hz) down 0 0 0 1/2/0 (549000000 Hz) down 0 0 0 1/2/1 (555000000 Hz) down 0 0 0 1/2/2 (561000000 Hz) down 0 0 0 1/2/3 (567000000 Hz) down 0 0 0 1/3/0 (549000000 Hz) up 0 0 0 testing 1/3/1 (555000000 Hz) up 0 0 0 1/3/2 (561000000 Hz) up 0 0 0 1/3/3 (567000000 Hz) up 0 0 0 casacasa

CASA CMTS

CASA-CMTS(config)#system monitor cpu enable

CASA CMTS

Configuring the management port

CASA-CMTS(config)# interface eth 0

CASA CMTS

CASA-CMTS(config-if-eth 0)# ip address 192.168.2.211 255.255.255.0 Reset to the default: CASA-CMTS(config-if-eth 0)# no ip address

CASA-CMTS(config-if-eth 0)# end

CASA-CMTS(config)# interface eth 0

CASA-CMTS(config)# interface eth 0 CASA-CMTS(config-if-eth 0)# ip address dhcp

CASA-CMTS(config)# interface eth 0

CASA CMTS

CASA-CMTS(config-if-eth0)# ip access-group my_access_group CASA-CMTS(config-if-eth0)# no ip access-group

Configuring Gigabit Ethernet (GigE) ports

CASA CMTS

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#

CASA-CMTS(config-if-gige 1)# no shutdown CASA-CMTS(config-if-gige 1)# end CASA-CMTS(config-if-gige 1)# shutdown CASA-CMTS(config-if-gige 1)# end

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#



CASA-CMTS(config-if-gige 1)# auto negotiate CASA-CMTS(config-if-gige 1)# no auto negotiate

CASA CMTS

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#

CASA-CMTS(config-if-gige)# ip address 192.168.3.100 255.255.255.0 CASA-CMTS(config-if-gige)#

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#

CASA CMTS

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)# ip access-group my_access_group CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)# no ip access-group

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#

CASA-CMTS(config-if-gige 1)# ipv6 address 2000::1000:1/64

CASA CMTS

CASA-CMTS(config-if-gige 1)# no ipv6 address

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#

CASA-CMTS(config-if-gige 1)# vlan 256 CASA-CMTS(config-if-gige 1)# no vlan

CASA CMTS

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#

CASA-CMTS(config-if-gige 1)# ip igmp CASA-CMTS(config-if-gige 1)#

CASA-CMTS(config-if-gige 1)# no ip igmp CASA-CMTS(config-if-gige 1)#

CASA-CMTS(config)#igmp client version 2

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)#

CASA CMTS

CASA-CMTS(config-if-gige 1)# mtu 1800

CASA-CMTS# show interface gige interface gige 0 ip address 192.168.3.110 255.255.255.0 no ip igmp .auto negotiate no shutdown no ip pim sparse-mode interface gige 1 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 2 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 3 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 4 no ip igmp auto negotiate no shutdown no ip pim sparse-mode

CASA CMTS

interface gige 5 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 6 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 7 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 8 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 9 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 10 no ip igmp auto negotiate no shutdown no ip pim sparse-mode interface gige 11 no ip igmp auto negotiate no shutdown no ip pim sparse-mode

CASA CMTS

CASA-C10G> show interface xgige interface xgige 6/0 ipv6 address 5000:0:130::13/64 mac address 00:17:10:03:60:ca no ip igmp no auto negotiate shutdown no ip pim sparse-mode interface xgige 6/1 ipv6 address 5000:0:130::23/64 mac address 00:17:10:03:60:cb no ip igmp no auto negotiate shutdown no ip pim sparse-mode

CASA CMTS

CASA-CMTS# show interface gige 0 stat Interface GIGE 0 statistics interface status UP link status DOWN auto-negotiation Enabled interface speed 1000 duplex status Full SFP vendor FINISAR CORP. SFP Serial Number P6E0JP6 SFP Type 1000BASE-T IfInOctets 0 IfInUcastPkts 0 IfInNUcastPkts 0 IfInDiscards 0 IfInErrors 0 IfInUnknownProtos 0 IfOutOctets 540 IfOutUcastPkts 0 IfOutNUcastPkts 6 IfOutErrors 0 IfOutDiscards 0 IpForwDatagrams 0 IpInReceives 0 IpInDiscards 0 CASA-C10G> show interface xgige 6/0 throughput Interface XGIGE 6/0 throughput IfInOctets 0 bytes/second IfInUcastPkts 0 packets/second IfInNUcastPkts 0 packets/second IfInTotalPkts 0 packets/second IfOutOctets 0 bytes/second IfOutUcastPkts 0 packets/second IfOutNUcastPkts 0 packets/second IfOutTotalPkts 0 packets/second

Configuring loopback interfaces

CASA CMTS

CASA-CMTS(config)# interface loopback 12 CASA-CMTS(conf-if-lo 12)#

CASA-CMTS(config)# interface loopback 4 CASA-CMTS(conf-if-lo 4)#

CASA CMTS

CASA-CMTS(config-if-lo 4)# ipv6 address 2000::1000:1/64 CASA-CMTS(config-if-lo 4)# no ipv6 address

CASA-CMTS(config)# interface loopback 0 CASA-CMTS(conf-if-lo 0)#

CASA-CMTS(config)# interface loopback 0 CASA-CMTS(conf-if-lo 0)#ip address 60.1.2.3 255.255.0.0

CASA-CMTS(config)# interface loopback 0 CASA-CMTS(conf-if-lo 0)#

CASA CMTS

CASA-CMTS(config-if-lo 0)#ip access-group my_access_group CASA-CMTS(config-if-lo 0)# no ip access-group

CASA-CMTS(config)# logging source-interface loopback 0

CASA-CMTS(config)# ftp-tftp source-interface loopback 0 CASA-CMTS(config)# no ftp-tftp sourceinterface loopback 0

CASA CMTS

CASA-CMTS(config)# lawful-intercept sourceinterface loopback 2

CASA-CMTS(config)# interface trunk 12

CASA CMTS

CASA-CMTS(conf-if-trunk 12)#

CASA-CMTS(config)# no interface trunk 12

CASA-CMTS(config)#interface trunk 12 C3000-230(conf-if-trunk 12)#

CASA-CMTS(config-if-trunk 12)#  description  “This   is  a  text  string  within  quotation  marks.”

CASA CMTS

CASA-CMTS(config)# interface trunk 1 CASA-CMTS(conf-if-trunk 1)#

CASA-CMTS(conf-if-trunk 6/1)# ip address 192.168.3.112 255.255.255.0 CASA-CMTS(conf-if-trunk 6/1)# ipv6 address 2000::1000:1/64 CASA-CMTS(conf-if-trunk)# no ipv6 address CASA-CMTS(conf-if-trunk)# no ip address

CASA CMTS

CASA-CMTS(config)# interface trunk 1 CASA-CMTS(conf-if-trunk 1#

CASA-CMTS(conf-if-trunk num)# no shutdown

CASA-CMTS(conf-if-trunk num)# shutdown

CASA-CMTS(config)# interface trunk 1 CASA-CMTS(conf-if-trunk) 1#

CASA CMTS

CASA-CMTS(conf-if-trunk 1)# gige 0 CASA-CMTS(conf-if-trunk 1)# no gige 0

CASA-CMTS(config)# interface trunk 1 CASA-CMTS(conf-if-trunk 1)#

CASA-CMTS(conf-if-trunk 1# ip igmp

CASA-CMTS(conf-if-trunk 1# no ip igmp

CASA-CMTS(config)# interface trunk 1

CASA CMTS

CASA-CMTS(conf-if-trunk 1)#

CASA-CMTS(conf-if-trunk 1)# ip access-group my_list CASA-CMTS(conf-if-trunk 1)# no ip access-group my_list

CASA-CMTS(config)# show interface trunk CASA-CMTS(config)# show interface trunk 1 ! interface trunk 1 gige 4 mode active gige 5 mode active gige 6 mode active

CASA CMTS

gige 7 mode active gige 8 mode active ip address 192.168.0.111 255.255.255.0 ip igmp ip access-group telnet_host ! no shutdown!

CASA-CMTS(config)# interface trunk 1 CASA-CMTS(conf-if-trunk 1)#

CASA-CMTS(config)# interface trunk 10 CASA-CMTS(conf-if-trunk 10)# show arp Interface Age Hardware Addr IP Address eth 6/0 00:00:01 0017.1001.5cab 192.168.8.1 eth 6/0 00:08:40 0022.0c9a.ea41 192.168.8.12 eth 6/0 00:18:01 bc30.5bd8.0f8e 192.168.8.90 eth 6/0 00:00:01 b8ac.6f8f.181f 192.168.8.92 eth 6/0 00:00:01 0017.1002.cc40 192.168.8.113 eth 7/0 00:08:24 0022.0c9a.ea41 192.168.8.12 eth 7/0 00:00:01 0017.1002.c4c0 192.168.8.114 CATV-MAC 1 00:00:01 0017.1002.cc4d fe80::217:10ff:fe02:cc4d CATV-MAC 2 00:00:01 0017.1002.cc4e fe80::217:10ff:fe02:cc4e

State

Type

dynamic ARPA dynamic ARPA dynamic ARPA dynamic ARPA static

ARPA

dynamic ARPA static

ARPA

static

ARPA

static

ARPA

CASA CMTS

Configuring DNS

CASA-CMTS(config)#nameserver 192.168.9.0 CASA-CMTS(config)#nameserver source-interface loopback 12

Configuring DHCP

CASA CMTS

CASA-CMTS(config)# dhcp-insert downstream-desctype 2 CASA-CMTS(config)# dhcp-insert enterprise-num 20858# CASA-CMTS(config)# dhcp-insert host-name-type 1 CASA-CMTS(config)# dhcp-insert upstream-desc-type 1

CASA CMTS

Related DHCP-insert commands

C3200-232(config)# interface docsis-mac 1 C3200-232(conf-if-mac 1)# dhcp-insert downstream-description C3200-232(conf-if-mac 1)# dhcp-insert hostname C3200-232(conf-if-mac 1)# dhcp-insert upstream-description C3200-232(conf-if-mac 1)#

/etc/dhcpd.conf allow leasequery;

key> key-id>





num> key>

CASA CMTS

num>







key>

CASA CMTS

key id> key>

CASA-CMTS(config-router-ospf)# area 3 virtual-link 10.10.10.3 message-digest-key 3 md5 3fk4j5ry76

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# auto-cost reference-bandwidth 20

CASA-CMTS(config-router-ospf)# no auto-cost reference-bandwidth 20

CASA CMTS

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# compatible rfc1583 CASA-CMTS(config-router-ospf)# no compatible rfc1583

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA CMTS

CASA-CMTS(config-router-ospf)# defaultinformation originate metric 50 metric-type 1

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# default-metric 20

CASA CMTS

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# distance ospf external 200

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA CMTS

CASA-C3000(config-router-ospf)# list area (A.B.C.D|) authentication area (A.B.C.D|) authentication message-digest area (A.B.C.D|) default-cost area (A.B.C.D|) export-list NAME area (A.B.C.D|) filter-list prefix WORD (in|out) area (A.B.C.D|) import-list NAME area (A.B.C.D|) nssa area (A.B.C.D|) nssa (translatecandidate|translate-never|translate-always) area (A.B.C.D|) nssa (translatecandidate|translate-never|translate-always) nosummary area (A.B.C.D|) nssa no-summary area (A.B.C.D|) range A.B.C.D/M area (A.B.C.D|) range A.B.C.D/M advertise area (A.B.C.D|) range A.B.C.D/M advertise cost

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA CMTS

CASA-CMTS(config-router-ospf)# neighbor 192.168.3.20 priority 1 poll-interval 140

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# network 10.10.10.0/24 area 1 CASA-CMTS(config-router-ospf)# network 10.10.20.1/24 area 2

CASA CMTS

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# ospf abr-type cisco

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# ospf router-id 192.168.3.20

CASA CMTS

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)# passive-interface gige 1 10.10.10.3

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA CMTS

CASA-CMTS(config-router-ospf)# distribute-list list1 out static

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA CMTS

CASA-CMTS(config-router-ospf)# redistribute static

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# refresh timer 100

CASA CMTS

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA-CMTS(config-router-ospf)# route-id 192.168.3.20

CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)#

CASA CMTS

CASA-CMTS(config-router-ospf)# timers spf 60 40

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip ospf authentication message-digest

CASA CMTS

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip ospf authentication-key neighbor

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA CMTS

CASA-CMTS(config-if-gige 0)# ip ospf cost 40

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip ospf deadinterval 33

CASA CMTS

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip ospf hellointerval 26

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA CMTS

CASA-CMTS(config-if-gige 0)# ip ospf messagedigest-key 12 md5 1007

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)# ip ospf retransmitinterval 10

CASA CMTS

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip ospf transmitdelay 10

CASA-CMTS(config)# show ip ospf OSPF Routing Process, Router ID: 192.168.3.95 Supports only single TOS (TOS0) routes This implementation conforms to RFC2328 RFC1583Compatibility flag is disabled SPF schedule delay 1 secs, Hold time between two SPFs 1 secs Refresh timer 10 secs Number of external LSA 0. Checksum Sum 0x0000000 Number of area attached to this router: 1 Area ID: 0.0.0.0 (Backbone)

CASA CMTS

Number of interfaces in this area: Total: 1, Active: 1 Number of fully adjacent neighbors in this area: 2 Area has no authentication SPF algorithm executed 30 times Number of router LSA 3. Checksum Sum0x0001c3bf Number of network LSA 1. Checksum Sum0x0000449d Number of summary LSA 1. Checksum Sum0x0000332c Number of ASBP summary LSA 0. Checksum Sum0x00000000 Number of NSSA LSA 0. Checksum Sum0x00000000

CASA-CMTS(config)# show ip ospf border-routers

CASA-CMTS(config)# show ip ospf database

CASA-CMTS(config)# show ip ospf interface

CASA CMTS

CASA-CMTS(config)# show ip ospf route

CASA CMTS

CASA-CMTS(config)# show ip route Codes: K – Kernel route, C - connected, S – static, R – RIP, O – OSPF, I – ISIS, B – BGP, > - selected route, * - FIB route C>* 10.109.2.0/24 is directly connected, bcm3 C>* 127.0.0.0/8 is directly connected, lo C>* 10.168.2.0/24 is directly connected, eth0 C>* 10.168.3.0/24 is directly connected, bcm1 C>* 10.168.66.0/24 is directly connected, bcm26 CASA-CMTS(config)#

CASA-CMTS(config)# show ipv6 route

CASA CMTS

CASA-CMTS# config CASA-CMTS(config)# CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)# CASA-CMTS(config-router-ospf)# redistribute connected CASA-CMTS(config-router-ospf)# network 192.168.3.0/24 area 0.0.0.0

.

CASA-CMTS# config CASA-CMTS(config)# CASA-CMTS(config)# router ospf CASA-CMTS(config-router-ospf)# CASA-CMTS(config-router-ospf)#network 192.168.3.0/24 area 0.0.0.0 CASA-CMTS(config-router-ospf)#network 10.237.1.0/24 area 0.0.0.0 CASA-CMTS(config-router-ospf)#network 10.237.2.0/24 area 0.0.0.0

Configuring the Routing Information Protocol

CASA CMTS

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# end

CASA CMTS

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)#defaultinformation originate

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)# default-metric 10

CASA CMTS

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# distance 100

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA CMTS

CASA-CMTS(config-router-rip)# distribute-list prefix area_3 in

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# list default-information originate default-metric distance distance A.B.C.D/M distance A.B.C.D/M WORD distribute-list WORD (in|out) distribute-list WORD (in|out) WORD distribute-list prefix WORD (in|out) distribute-list prefix WORD (in|out) WORD end exit list neighbor A.B.C.D network (A.B.C.D/M|WORD) no default-information originate no default-metric no default-metric no distance no distance A.B.C.D/M no distance A.B.C.D/M WORD no distribute-list WORD (in|out) no distribute-list WORD (in|out) WORD no distribute-list prefix WORD (in|out) no distribute-list prefix WORD (in|out) WORD no neighbor A.B.C.D

CASA CMTS

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# neighbor 10.10.10.3

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)# network

CASA CMTS

10.10.10.3/24 CASA-CMTS(config-router-rip)# network 192.168.3.4/24

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# offset-list acl2 out 15

CASA CMTS

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# passive interface default

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA CMTS

CASA-CMTS(config-router-ospf)# redistribute static

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# route 192.168.2.3/24

CASA CMTS

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA-CMTS(config-router-rip)# route-map test in gige2

CASA-CMTS(config)# router rip CASA-CMTS(config-router-rip)#

CASA CMTS

CASA-CMTS(config-router-rip)# timers basic 5 15 15

CASA-CMTS(config-router-rip)# version 2

CASA CMTS

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip rip authentication key-chain school CASA-CMTS(config-if-gige id)# no ip rip authentication key-chain

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip rip authentication string public CASA-CMTS(config-if-gige id)# no ip rip authentication string

CASA CMTS

CASA-CMTS(config)# interface gige 0 CASA-CMTS(config-if-gige 0)#

CASA-CMTS(config-if-gige 0)# ip rip authentication mode md5 auth-length rfc

CASA-CMTS(config)# show ip rip Codes: R – RIP, C – connected, S – static, O – OSPF, B – BGP Sub-codes: (n) – normal, (s) – static, (d) – default. (r) – redistribute, (i) - interface Network Metric From Tag Time C(i) 192.168.3.0/24 1 self 0

Next Hop 0.0.0.0

CASA CMTS

CASA-CMTS(config)# show ip rip status Routing  Protocol  is  “rip” Sending updates every 30 seconds with +/-50% next due in 4 seconds Timeout after 180 seconds, garbage collect after 120 seconds Outgoing update filter list for all interface in not set Incoming update filter list for all interface in not set Default redistribution metric is 1 Redistributing: Default version control: send version 2, receive any version Interface Send Recv Key-chain Bcm2 2 1 2 Routing for Networks: 192.168.3.0/24 Routing Information Sources: Gateway Badpackets BadRoutes Distance Last Update Distance: (default is 120)

CASA CMTS

CASA-CMTS(config)# show ip route Codes: K – Kernel route, C - connected, S – static, R – RIP, O – OSPF, I – ISIS, B – BGP, > - selected route, * - FIB route C>* 10.109.2.0/24 is directly connected, bcm3 C>* 127.0.0.0/8 is directly connected, lo C>* 10.168.2.0/24 is directly connected, eth0 C>* 10.168.3.0/24 is directly connected, bcm1 C>* 10.168.66.0/24 is directly connected, bcm26 CASA-CMTS(config)#

CASA-CMTS(config)# show ipv6 route

CASA CMTS

Configuring the BGP Routing Protocol (Release 5.4 and later)

CASA-CMTS(config)# router bgp 5 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA-CMTS(config)# router bgp 5 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# bgp router-id A.B.C.D

CASA-CMTS(config)# router bgp 5 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA-CMTS(config-router-bgp)# distance bgp

CASA-CMTS(config)# router bgp 5 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# distance 5 60.3.4.5/24 list5

CASA CMTS

CASA-CMTS(config)# router bgp 5 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# network 10.0.0.0/8

CASA CMTS

CASA-CMTS(config)# router bgp 5 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bbp)# aggregateaddress 192.168.6.7/24 as-set summary-only

CASA-CMTS(config)# router bgp 5 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA-CMTS(config-router-ospf)# redistribute static

can’t  find  neighbor  A.B.C.D

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA-CMTS(config-router-bgp)# neighbor 10.0.0.1 remote-as 2

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)# string

string

CASA CMTS

CASA-CMTS(config-router-bgp)# neighbor 10.0.0.1 password

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# no neighbor 64.10.1.0 shutdown

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA-CMTS(config-router-bgp)# neighbor 63.10.1.0 ebgp-multihop 50

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#[ no] neighbor peer description

CASA-CMTS(config)# router bgp 1

CASA CMTS

CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#neighbor 192.168.3.1 version 4

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#neighbor 192.168.3.4 interface ifname

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# neighbor 192.168.3.4 next-hop-self

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#[no] neighbor 192.168.3.4 default-originate

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#[no] neighbor peer update-source 4

CASA-CMTS(config)# router bgp 1

CASA CMTS

CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# neighbor 192.168.3.4 send-community

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config)# neighbor 192.168.3.4 weight 5

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# neighbor 192.168.3.4 maximum-prefix 100

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# neighbor 192.168.3.4 distribute-list list1 in

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA-CMTS(config-router-bgp)#neighbor peer prefix-list prefixList1 out

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#neighbor peer filter-list filterList1 in

CASA-CMTS(config)# router bgp 1

CASA CMTS

CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#neighbor peer route-map [in | out]

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)#neighbor group1

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# neighbor 192.168.3.4 peer-group peerGroup1

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA-CMTS(config-router-bgp)# address-family ipv4 unicast

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA CMTS

CASA CMTS

CASA CMTS

CASA CMTS



CASA-CMTS(config-router-bgp)# address-family ipv6 unicast CASA-CMTS(config-router-af)# exit-address-family CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 activate CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 advertisement-interval 100 CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 allowas-in 5 CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 attribute-unchanged as-path med next-hop CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 capability orf prefix-list both CASA-CMTS(config-router-af)# neighbor 2001:1::1:1

CASA CMTS

default-originate route-map map1 CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 distribute-list acl1 in CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 filter-list list1 out CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 maximum-prefix 100 warning-only CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 next-hop-self CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 prefix-list list1 in CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 remove-private-AS CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 route-map map1 in CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 send-community both CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 soft-reconfiguration inbound CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 unsuppress-map map1 CASA-CMTS(config-router-af)# neighbor 2001:1::1:1 weight 600 CASA-CMTS(config-router-af)# network 2001:1::1:1/64 CASA-CMTS(config-router-af)# redistribute connected

RFC1930

CASA CMTS

>

CASA-CMTS(config)#ip as-path access-list list1 permit regExpression

CASA CMTS

CASA-CMTS(config)#ip community-list 123 permit internet

CASA CMTS

Example 1

router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list 70 permit 7675:70 ip community-list 70 deny ip community-list 80 permit 7675:80 ip community-list 80 deny ip community-list 90 permit 7675:90 ip community-list 90 deny ! route-map RMAP permit 10 match community 70 set local-preference 70 ! route-map RMAP permit 20 match community 80 set local-preference 80 ! route-map RMAP permit 30 match community 90 set local-preference 90

Example 2

router bgp 100 network 10.0.0.0/8 neighbor 192.168.0.2 remote-as 7675 neighbor 192.168.0.2 route-map RMAP out

CASA CMTS

! ip access-list ! Permit all 10.0.0.0 255.0.0.0 any any route-map RMAP permit 10 match ip address acl set community 7675:80

Example 3

router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list 1 permit 0:80 0:90 ! route-map RMAP permit in match community 1

Example 4

router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list standard FILTER deny 1:1 ip community-list standard FILTER permit ! route-map RMAP permit 10 match community FILTER

ip community-list standard INTERNET deny 1:1 ip community-list standard INTERNET permit internet

Example 5

CASA CMTS

router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list standard DEL permit 100:1 100:2 ! route-map RMAP permit 10 set comm-list DEL delete router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list 70 permit 7675:70 ip community-list 70 deny ip community-list 80 permit 7675:80 ip community-list 80 deny ip community-list 90 permit 7675:90 ip community-list 90 deny ! route-map RMAP permit 10 match community 70 set local-preference 70 ! route-map RMAP permit 20 match community 80 set local-preference 80 ! route-map RMAP permit 30 match community 90 set local-preference 90

Example 6

router bgp 100 network 10.0.0.0/8 neighbor 192.168.0.2 remote-as 7675 neighbor 192.168.0.2 route-map RMAP out ! ip ip access-list acl ! Permit all 10.0.0.0 255.0.0.0 any route-map RMAP permit 10 match ip address acl set community 7675:80

Example 7

CASA CMTS

router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list 1 permit 0:80 0:90 ! route-map RMAP permit in match community 1

Example 8

router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list standard FILTER deny 1:1 ip community-list standard FILTER permit ! route-map RMAP permit 10 match community FILTER

ip community-list standard INTERNET deny 1:1 ip community-list standard INTERNET permit internet

Example 9

router bgp 7675 neighbor 192.168.0.1 remote-as 100 neighbor 192.168.0.1 route-map RMAP in ! ip community-list standard DEL permit 100:1 100:2 ! route-map RMAP permit 10 set comm-list DEL delete

CASA CMTS

Where: type num

CASA-CMTS# show interface eth 0 acl-count details 10 deny icmp 192.168.0.250 255.255.255.255 192.168.0.188 255.255.255.255 (8 matches)

Where: string

Where: string

CASA CMTS

CASA-CMTS# show ip bdg attribute-info

CASA-CMTS# show ip bgp dampened-paths

CASA-CMTS# show ip bgp neighbors

CASA-CMTS# show ip bgp paths

CASA-CMTS# show ip bgp rsclient

CASA CMTS

CASA-CMTS# show ip bgp scan

CASA-CMTS# show ip bgp summary

CASA-CMTS# show ip bgp attribute-info

CASA-CMTS# show ip bgp dampened-paths

CASA CMTS

CASA-CMTS# clear ip bgp external

CASA-CMTS# clear ip bgp 60.5.6.7 in

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# neighbor 192.168.3.4 dont-capability-negotiate

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# bgp cluster-id 300

CASA CMTS

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# [no] neighbor peer route-reflector-client

CASA-CMTS(config)# router bgp 1 CASA-CMTS(config-router-bgp)#

CASA-CMTS(config-router-bgp)# bgp network importcheck

CASA CMTS

IP access control

Where: acl_name

CASA-CMTS(config)# ip access-list telnet_host CASA-CMTS(conf-acl telnet_host)#

CASA-CMTS(config)# no ip access-list telnet_host

CASA CMTS

Where: acl_name

CASA-CMTS(config)# ip access-list telnet_host CASA-CMTS(conf-acl telnet_host)#

CASA-CMTS(conf-acl telnet_host)# end CASA-CMTS(config)

Where: acl_name

CASA-CMTS(config)# ip access-list telnet_host CASA-CMTS(conf-acl telnet_host)#

Where: sequence-number

CASA CMTS



CASA-CMTS(conf-acl telnet_host)# 100 permit telnet 192.168.2.222 CASA-CMTS(conf-acl telnet_host)# Where: sequence-number

CASA CMTS

CASA-CMTS(conf-acl telnet_host)# no 100 CASA-CMTS(conf-acl telnet_host)#

Where:

CASA-CMTS(config)# ip access-list telnet_host CASA-CMTS(conf-acl telnet_host)# string

CASA-CMTS(conf-acl telnet_host)#10  remark  “This  is   a  remark.”

CASA-CMTS(conf-acl telnet_host)# no 10

Where:

CASA CMTS

CASA-CMTS(config)# show ip access-list telnet_host 10 permit telnet 192.168.2.38 255.255.255.255.254 any 20 deny telnet any any 30 deny icmp 192.168.2.19 255.255.255.255 any

CASA-CMTS(config)# show ip access-list ip access-list telnet_host ip access-list ftp_host ip access-list tftp_host

CASA-CMTS(conf-acl telnet_host)# 100 permit telnet 192.168.2.222 CASA-CMTS(conf-acl telnet_host)# 200 deny telnet any

CASA-CMTS(conf-acl telnet_host)# show ip access-list telnet_host 10 permit telnet 192.168.2.238 255.255.255.255 any 20 deny telnet any any

CASA CMTS

CASA-CMTS(conf-acl telnet_host)# CASA-CMTS(conf-acl telnet_host)# 10 permit telnet 192.168.2.238 15 permit telnet 192.168.2.222 20 deny telnet any any

15 permit telnet 192.168.2.222 show ip access-list telnet_host 255.255.255.255 any 255.255.255.255 any

CASA-CMTS(conf-acl telnet_host)# CASA-CMTS(conf-acl telnet_host)# 10 permit telnet 192.168.2.238 20 permit telnet 192.168.2.222 30 deny telnet any any

resequence show ip access-list telnet_host 255.255.255.255 any 255.255.255.255 any

Where:

CASA-CMTS(config)# interface eth 0 CASA-CMTS(config-if-eth 0)#

CASA CMTS

Where:

CASA-CMTS(config-if-eth 0)# ip access-group telnet_host

Where:

CASA-CMTS(config)# interface gige 1 CASA-CMTS(config-if-gige 1)# Where:

CASA-CMTS(config-if-gige telnet_host

1)# ip access-group

CASA-CMTS(config-if-eth 0)# no ip access-group

CASA CMTS

acl_name Where:

CASA-CMTS(config)# access-class in tftp_host CASA-CMTS(config)# no access-class in

acl_name

Where:

CASA-CMTS(config)# access-class out tftp_host CASA-CMTS(config)# no access-class out

Configuring route maps

CASA CMTS

Where:

CASA-CMTS(config)# route-map cmtsNet1 permit 100

CASA-CMTS(config)# no route-map cmtsNet1

CASA CMTS

Where:

CASA-CMTS(conf-route-map cmtsNet1)# match as-path as10

CASA-CMTS(conf-route-map cmtsNet1)# no match aspath as10

Where:

CASA CMTS

CASA-CMTS(conf-route-map cmtsNet1)# match community 70 CASA-CMTS#(conf-route-map cmtsNet1)# community

no match

Where:

CASA-CMTS(conf-route-map cmtsNet1)# match ip address as2 CASA-CMTS(conf-route-map cmtsNet1)# # match ip next-hop as4

CASA-CMTS(conf-route-map cmtsNet1)# no match ip address CASA-CMTS(conf-route-map cmtsNet1)# no match ip next-hop

CASA CMTS

Where:

CASA-CMTS(conf-route-map cmtsNet1)# match metric 5

CASA-CMTS(conf-route-map cmtsNet1)# no match metric

Where:

CASA CMTS

CASA-CMTS(conf-route-map cmtsNet1)# match origin egp

CASA-CMTS(conf-route-map cmtsNet1)# no match origin egp

Where:

CASA-CMTS(conf-route-map cmtsNet1)# match peer 192.168.8.7 CASA-CMTS(conf-route-map cmtsNet1)# match peer local

CASA-CMTS(conf-route-map cmtsNet1)# no match peer 192.168.8.7 CASA-CMTS(conf-route-map cmtsNet1)# no match peer local

Where:

CASA CMTS

CASA-CMTS(conf-route-map cmtsNet1)# match tag 57

CASA-CMTS(conf-route-map cmtsNet1)# no match tag 57

Where:

CASA-CMTS(conf-route-map cmtsNet1# set as-path prepend 5

CASA CMTS

CASA-CMTS(conf-route-map cmtsNet1# no set as-path prepend 5

CASA-CMTS(conf-route-map cmtsNet1)# set atomic-aggregate

CASA-CMTS(conf-route-map cmtsNet1)# no set atomic-aggregate

CASA CMTS

Where:

CASA-CMTS(conf-route-map cmtsNet1)# set community 225:1 CASA-CMTS(conf-route-map cmtsNet1)# no set community

Where:

CASA-CMTS(conf-route-map cmtsNet1)# set ip nexthop 192.168.3.0

CASA-CMTS(conf-route-map cmtsNet1)# no set ip next-hop

CASA CMTS

Where:

CASA-CMTS(conf-route-map cmtsNet1# set localpreference 5

CASA-CMTS(conf-route-map cmtsNet1# no set localpreference

Where:

CASA-CMTS(conf-route-map cmtsNet1)# set metric 5 CASA-CMTS(conf-route-map cmtsNet1)# no set metric

CASA CMTS

Where:

CASA-CMTS(conf-route-map cmtsNet1)# set origin egp

CASA-CMTS(conf-route-map cmtsNet1)# no set origin egp

Where:

CASA CMTS

CASA-CMTS(conf-route-map cmtsNet1)# set originatorid 192.268.3.4

CASA-CMTS(conf-route-map cmtsNet1)# no set originator-id

Where:

CASA-CMTS(conf-route-map cmtsNet1)# set weight 100 CASA-CMTS(conf-route-map cmtsNet1)# no set weight

Configuring Virtual Local Area Networks (VLANs)

CASA CMTS

CASA-CMTS(config)#interface vlan 2 CASA-CMTS(config-if-vlan 2)

CASA-CMTS(config)#interface vlan 2

CASA-CMTS(config-if-vlan  10)#  description  “This   is  a  text  string  within  quotation  marks.”

CASA CMTS

CASA-CMTS(config)#interface vlan 300 1000 2000 3000 3500 3600 CASA-CMTS(config)#no interface vlan 300 1000 2000 3000 3500 3600

CASA-CMTS(config)#interface vlan range 300 400 CASA-CMTS(conf-if-vlan 300)# CASA-CMTS(config)#no interface vlan range 300 400

CASA CMTS

CASA-CMTS(config)#interface vlan 2 CASA-CMTS(conf-if-vlan 2)

CASA-CMTS(conf-if-vlan 2)#mac address xxxx.xxxx.xxxx

CASA-CMTS(config)# interface vlan 256 CASA-CMTS(conf-if-vlan 256)#

CASA-CMTS(conf-if-vlan 256)# gige 1

CASA CMTS

CASA-CMTS(config)# interface vlan 10 CASA-CMTS(conf-if-vlan 6/10)#

CASA-CMTS(conf-if-vlan 6/10)# xgige 6/0

CASA-CMTS(config)# interface vlan 256 CASA-CMTS(conf-if-vlan 256)#

CASA-CMTS(conf-if-vlan 256)# no gige 1

CASA CMTS

CASA-CMTS(config)# interface vlan 10 CASA-CMTS(conf-if-vlan 6/10)#

CASA-CMTS(conf-if-vlan 6/10)# no xgige 6/0

CASA-CMTS(config)# interface vlan 10 CASA-CMTS(conf-if-vlan 6/10)# gige 4 CASA-CMTS(conf-if-vlan 6/10)# show this interface vlan 6/10 gige 6/4 no shutdown

CASA CMTS

CASA-CMTS(config-if-vlan 10)# ip address 192.168.3.100 255.255.255.0 CASA-CMTS(config-if-vlan 10)#

CASA-CMTS(config)# interface vlan 10 CASA-CMTS(conf-if-vlan 6/10)# gige 4 CASA-CMTS(conf-if-vlan 6/10)# show this interface vlan 6/10 gige 6/4 no shutdown

CASA CMTS

CASA-CMTS(config-if-vlan 6/10)# ipv6 address 2000::1000:1/64 CASA-CMTS(config-if-gige 1)# no ipv6 address

CASA-CMTS(config)#interface vlan 10

CASA-CMTS(config)# interface vlan 2 CASA-CMTS(conf-if-vlan 2)# rate-limit multicast 1500

CASA CMTS

CASA-CMTS(config)# interface qam 0/2 CASA-CMTS(conf-if-qam)#

CASA-CMTS(conf-if-qam 0/2)# vlan 256 CASA-CMTS(config-if-qam 0/2)# CASA-CMTS(conf-if-qam 0/2)# no vlan CASA-CMTS(conf-if-qam)#

CASA-CMTS(config)#interface vlan 2

CASA-CMTS(conf-if-vlan)# ip access-group my_access_group

CASA CMTS

CASA-CMTS(conf-if-vlan)# no ip access-group my_access_group

CASA-CMTS(config)#interface vlan 10

CASA-CMTS(conf-if-vlan 10)# trunk 24 CASA-CMTS(conf-if-vlan)# no trunk 12

Example: Create trunk and add interfaces; add trunk to VLAN. CASA-CMTS(config)# interface trunk 12 CASA-CMTS(conf-if-trunk 12)# CASA-CMTS(conf-if-trunk 12)#gige 3 CASA-CMTS(conf-if-trunk 12)#gige 4 CASA-CMTS(conf-if-trunk 12)#end CASA-CMTS(config)# interface vlan 10 CASA-CMTS(conf-if-vlan 10)#trunk 10 CASA-CMTS(conf-if-vlan 10)#ip address 192.67.43.1 255.255.0.0

CASA CMTS

CASA-CMTS(config)# show interface vlan interface gige 0, vlan 2 interface gige 1, vlan 256 interface gige 2, vlan 2 interface gige 3, vlan 2 interface qam 0/0, vlan 2 interface qam 0/1, vlan 256 interface qam 0/2, vlan 2 interface qam 0/3, vlan 2 .

CASA-CMTS(config)#show interface vlan interface vlan 2 no ip igmp interface vlan 300 gige 0 no ip igmp

CASA CMTS

CASA-CMTS(config)# interface vlan 10 CASA-CMTS(conf-if-vlan 6/10)#

CASA-CMTS(config)# interface vlan 10 CASA-CMTS(conf-if-vlan 6/10)# show arp Interface Age Hardware Addr IP Address eth 6/0 00:00:01 0017.1001.5cab 192.168.8.1 eth 6/0 00:08:40 0022.0c9a.ea41 192.168.8.12 eth 6/0 00:18:01 bc30.5bd8.0f8e 192.168.8.90 eth 6/0 00:00:01 b8ac.6f8f.181f 192.168.8.92 eth 6/0 00:00:01 0017.1002.cc40 192.168.8.113 eth 7/0 00:08:24 0022.0c9a.ea41 192.168.8.12 eth 7/0 00:00:01 0017.1002.c4c0 192.168.8.114 CATV-MAC 1 00:00:01 0017.1002.cc4d fe80::217:10ff:fe02:cc4d CATV-MAC 2 00:00:01 0017.1002.cc4e fe80::217:10ff:fe02:cc4e

State

Type

dynamic ARPA dynamic ARPA dynamic ARPA dynamic ARPA static

ARPA

dynamic ARPA static

ARPA

static

ARPA

static

ARPA

CASA CMTS

Configuring L2VPN

C10G-203(config)#show interface vlan 10 interface vlan 6/10 xgige 6/1 no ip igmp no ip pim sparse-mode no shutdown

CASA CMTS

CASA-CMTS(config)# interface vlan 400 CASA-CMTS(conf-if-vlan 400)#

CASA-CMTS(config)# interface vlan 400 CASA-CMTS(conf-if-vlan 400)#

CASA CMTS

CASA-CMTS(config)# no l2vpn mac-address-movable

CASA-CMTS# show l2vpn local-traffic-forwarding no l2vpn mac-address-movable no l2vpn local-traffic-forwarding

C10G-203(config)#show l2vpn vlan 10 l2vpn vlan table: vlan_id=10

CASA CMTS

C10G-203(config)#show l2vpn qam 1 lc: logical=1 phy=1 L2VPN US: ttl=0 drop=0 DS: ttl=0 drop=0 NotDefined pkt=0 id=0 bc_src=0 local: mac_addr_movable 0 traffic_fwd 0 l2vpn_vlan_tbl_prt(): l2vpn_addr_hs_tbl_prt():

Configuring TACACS (Release 5.4)

CASA-CMTS(config)tacacs-server host 192.168.10.1#

CASA CMTS

CASA-CMTS(config) tacacs-server key abcd

CASA-CMTS(config)# aaa authentication enable default group radius

CASA-CMTS(config)# no aaa authentication enable

CASA CMTS

CASA-CMTS(config)# aaa authentication ascii

CASA-CMTS(config)# aaa authentication login default group tacacsplus

CASA CMTS

CASA-CMTS(config)# aaa authentication login radius

CASA-CMTS(config)# aaa authorization command 1 default local tacacsplus

CASA-CMTS(config)# aaa authorization exec default group tacacsplus local

CASA CMTS

aaa authorization exec default if-authenticated group tacacsplus

CASA-CMTS(config)# aaa accounting commands 4 default start-stop

CASA CMTS

CASA-CMTS(config)# aaa radius-source loopback 4

CASA CMTS

CASA-CMTS(config)# radius server host server1 key 123 7

CASA-CMTS(config)# no radius server host server1/123

CASA-CMTS# show aaa ----------------- AAA Configurations ---------------AAA Server IP Address : 192.168.100.1 (KEY: test) AAA Server Encryption Key : test AAA Authentication : LOGIN, ON ENABLE, ON AAA Authentication method : TACACS+, LOCAL AAA CMD Authorization : ON : COMMAND 15 TACACSPLUS : OTHER COMMAND LEVEL(S) LOCAL AAA Accounting : COMMAND LEVEL 15 TRIGGERSTARTSTOP : NO COMMAND ACC TRIGGER FOR OTHER LEVEL(S) : EXEC ACC TRIGGER LOGIN-LOGOUT

CASA CMTS

Stream configuration and management

CASA CMTS

CASA-CMTS(config)# operation mode manual CASA-CMTS(config)#

CASA CMTS

CASA-CMTS(config)# operation mode rpc CASA-CMTS(config)#

CASA CMTS

CASA-CMTS(config)# operation mode auto CASA-CMTS(config)#

CASA CMTS

CASA-CMTS(config)# operation mode group-4-port CASA-CMTS(config)#

CASA CMTS

CASA-CMTS(config)# operation mode group-2-port CASA-CMTS(config)#

CASA CMTS



CASA-CMTS(config)# dejitter interval 200 CASA-CMTS(config)# CASA-CMTS(config)# no dejitter interval CASA-CMTS(config)#





CASA-CMTS(config)# stream 123 CASA-CMTS(config-stream 123)#

CASA-CMTS(config-stream)# end CASA-CMTS(config)#

CASA CMTS





CASA-CMTS(config)# stream 123

CASA-CMTS(config-stream 123) ip source address 192.168.4.10 CASA-CMTS(config-stream 123)#

CASA-CMTS(config-stream 123)# no ip source address CASA-CMTS(config-stream)





CASA-CMTS(config)# stream 123 CASA-CMTS(config-stream 123)#

CASA CMTS

CASA-CMTS(config-stream 123) ip destination address 192.168.3.10 CASA-CMTS(config-stream 123)#

CASA-CMTS(config-stream 123)# no ip destination address CASA-CMTS(config-stream 123)#

CASA-CMTS(config)# stream 123 CASA-CMTS(config-stream 123)#

CASA-CMTS(config-stream 123)# udp source port 1234 CASA-CMTS(config-stream 123)#

CASA-CMTS(config-stream 123)# no udp source port CASA-CMTS(config-stream 123)#

CASA CMTS

CASA-CMTS(config)# stream 123 CASA-CMTS(config-stream 123)#

CASA-CMTS(config-stream 123)# udp destination port 4321 CASA-CMTS(config-stream 123)#

CASA-CMTS(config-stream 123)# no udp destination port CASA-CMTS(config-stream 123)#

CASA-CMTS(config)# show stream config 14 configuration for stream 14 -------------------------------------------------

CASA CMTS

ip source address is ip destination address is udp source port is udp destination port is Dejitter buffer is millisecond

wildcard wildcard wildcard 3014 400

Show the configuration of all configured streams: CASA-CMTS(config)# show stream config stream configuration: stream 1 ip source address is wildcard ip destination address is wildcard udp source port is wildcard udp destination port is 3001 Dejitter buffer is 400 millisecond stream 2 ip source address is ip destination address is udp source port is udp destination port is Dejitter buffer is millisecond … stream 14 ip source address is ip destination address is udp source port is udp destination port is Dejitter buffer is millisecond CASA-CMTS(config)#

wildcard wildcard wildcard 3002 400

wildcard wildcard wildcard 3014 400

CASA CMTS

CASA-CMTS(config)# interface qam 0/2 CASA-CMTS(config-if-qam)#

CASA-CMTS(config-if-qam)# channel 1 stream 123 program 100 CASA-CMTS(config-if-qam)#

CASA-CMTS(config-if-qam)# channel 0 stream 223 pass-through CASA-CMTS(config-if-qam)#

CASA-C2150(config-if-qam)# no channel 1 stream 123 CASA-C2150(config-if-qam)#

CASA CMTS

: CASA-CMTS# show module 0 stream no-mapping Module 0 - Stream with no mapping

CASA-CMTS(config)# operation mode group-4 port

CASA-CMTS(config)# interface gige 3

CASA-CMTS(config-if-gige 3)# no shutdown N/A

CASA-CMTS(config)# interface qam 0/0 CASA-CMTS(config-if-qam0/0)# ip add a.b.c.d

CASA CMTS

Configuring downstream QAM ports

/

CASA-CMTS(config)# interface qam 0/0 CASA-CMTS(config-if-qam)#

CASA CMTS

CASA-CMTS(config)# interface qam 0/0 CASA-CMTS(config-if-qam)#

CASA-CMTS(config-if-qam 0/0)# end CASA-CMTS(config)#

/

CASA-CMTS(config)# interface qam 0/0 CASA-CMTS(config-if-qam)#

Enable QAM port 0 on module 0: CASA-CMTS(config-if-qam)# no shutdown CASA-CMTS(config-if-qam)#

CASA CMTS

/

CASA-CMTS(config)# interface qam 0/0 CASA-CMTS(config-if-qam)#

Enable QAM port 0 on module 0: CASA-CMTS(config-if-qam)# shutdown

CASA-CMTS#config CASA-CMTS(config)# /

CASA-CMTS(config)# interface qam 1/3 CASA-CMTS(config-if-qam 1/3)#

CASA CMTS

CASA-CMTS(config-if-qam 1/3)# no channel 1 shutdown CASA-CMTS(config-if-qam 1/3)#

/

CASA-CMTS(config)# interface qam 0/2 CASA-CMTS(config-if-qam 0/2)#

CASA-CMTS(config-if-qam 0/2)# channel 2 shutdown CASA-CMTS(config-if-qam 0/2)#

/

CASA CMTS

CASA-CMTS(config)# interface qam 1/2 CASA-CMTS(config-if-qam 1/2)#

CASA-CMTS(config-if-qam 1/2)# ip address 192.168.3.211 255.255.255.0 CASA-CMTS(config-if-qam 1/2)# CASA-CMTS(config-if-qam 1/2)# no ip address CASA-CMTS(config-if-qam 1/2)#

/

CASA-CMTS(config)# interface qam 1/2 CASA-CMTS(config-if-qam 1/2)#

CASA CMTS

CASA-CMTS(config-if-qam)# mac address 1234.2345.3456 CASA-CMTS(config-if-qam)# Return  to  the  manufacturer’s  built-in MAC address: CASA-CMTS(config-if-qam)# no mac address CASA-CMTS(config-if-qam)#

/

CASA-CMTS(config)# interface qam 0/3 CASA-CMTS(config-if-qam 0/3)#

CASA-CMTS(config-if-qam 0/3)# modulation 64qam

CASA CMTS

/

CASA-CMTS(config)# interface qam 0/2 CASA-CMTS(config-if-qam 0/2)#

CASA-CMTS(config-if-qam 0/2)# annex B CASA-CMTS(config-if-qam 0/2)#

CASA CMTS

CASA-CMTS(config-if-qam 0/2)# annex A symbol rate 6000 channel spacing 7000000 CASA-CMTS(config-if-qam 0/2)#

/

CASA-CMTS(config)# interface qam 0/3 CASA-CMTS(config-if-qam 0/3)#

CASA CMTS

CASA-CMTS(config-if-qam 0/3)# channel 1 frequency 555000000 CASA-CMTS(config-if-qam 0/3)#

/

CASA-CMTS(config)# interface qam 0/3 CASA-CMTS(config-if-qam 0/3)#

CASA CMTS

CASA-CMTS(config-if-qam 0/2)# power 550 CASA-CMTS(config-if-qam 0/2)#

/

CASA CMTS

CASA-CMTS(config)# interface qam 0/3 CASA-CMTS(config-if-qam 0/3)#

CASA-CMTS(config-if-qam)# interleave 128x8 CASA-CMTS(config-if-qam)#

/

CASA-CMTS(config)# interface qam 0/3 CASA-CMTS(config-if-qam 0/3)#

CASA-CMTS(config-if-qam 0/3)# spectral inversion on

CASA CMTS

CASA-CMTS(config-if-qam 0/3)# no spectral inversion on

CASA-CMTS(config) show interface qam 2/1 brief

CASA-CMTS(config) show interface qam 2/1/0

CASA CMTS

CASA-2200(config)# show docsis downstream channel utilization Downstream Slot/Port/Channel Utilization (%) 2/0/0 2 2/0/1 2 2/0/2 2 2/0/3 2 2/1/0 0 2/1/1 0 2/1/2 0 2/1/3 0 2/2/0 0 2/2/1 0 2/2/2 0 2/2/3 0 2/3/0 0 2/3/1 0 2/3/2 0 2/3/3 0

C10G(config)# show downstream channel set MAC Chan Channel ID Set List 1 1 0/0/0 1 2 0/0/1 1 3 0/0/2 1 4 0/0/3 1 5 0/0/4 1 6 0/0/5 1 7 0/0/6 1 8 0/0/7

CASA CMTS

1 2 2 2 2 2 2 2 2 2

256 1 2 3 4 5 6 7 8 256

0/0/0, 0/0/1, 0/0/2, 0/0/3, 0/0/4 0/1/8 0/1/9 0/1/10 0/1/11 0/1/12 0/1/13 0/1/14 0/1/15 0/1/8, 0/1/9, 0/1/10, 0/1/11, 0/1/12

C10G(config)#show downstream channel set | count-only / Count Line: 72 C10G(config)#

Configuring upstream port interfaces

C10G-CMTS(config-if-ups 11/0.1)#show upstream upstream channel burst noise rate (events/sec) 11/0.0/0 0.0 11/0.0/1 0.0 11/0.1/0 0.0

CASA CMTS

11/0.1/1

0.0

C10G(config-if-ups 13/0.0)# show interface upstream 13/0 interface upstream 13/0.0 spectrum-rule 35 frequency 5000000 channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit ingress-cancellation 100 logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 6400000 logical-channel 0 profile 4 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 0 ranging-backoff 0 4 logical-channel 0 pre-equalization logical-channel 0 power-offset 0 logical-channel 0 ranging-priority 0x0 logical-channel 0 class-id 0x0 no logical-channel 0 shutdown logical-channel 1 prov-attr-mask 0x0 logical-channel 1 channel-width 3200000 logical-channel 1 profile 4 logical-channel 1 minislot 8

CASA CMTS

logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 no logical-channel 1 shutdown no shutdown

CASA-CMTS#config CASA-CMTS(config)#

CASA-CMTS(config)# interface upstream 2/6 CASA-CMTS(config-if-ups 2/6)#

CASA CMTS

CASA-CMTS(config-if-ups 2/0)# end CASA-CMTS(config)#

CASA-CMTS(config)# interface upstream 2/6 CASA-CMTS(config-if-ups 2/6)#

CASA-CMTS(config-if-ups 3/7)# no shutdown CASA-CMTS(config-if-ups 3/7)#

CASA-CMTS(config)# interface upstream 2/6

CASA CMTS

CASA-CMTS(config-if-ups 2/6)#

CASA-CMTS(config-if-ups 3/7)# shutdown CASA-CMTS(config-if-ups 3/7)#

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups  11/0.0)#  description  “This   is  a  text  string  within  quotation  marks.” CASA-CMTS(config-if-ups 11/0.0)#logical channel 1 description  “This  is  a  sample  string.”

CASA-CMTS(config)# show interface upstream brief interface upstream 4/0.0 frequency 20000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown no shutdown interface upstream 4/0.1 frequency 24000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown no shutdown interface upstream 4/1.0 frequency 20000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown shutdown

CASA CMTS

Example: Showing upstream port interface configurations CASA-CMTS# show interface upstream 4 interface upstream 4/0.0 frequency 20000000 channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit no ingress-cancellation logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 0 ranging-backoff 0 4 no logical-channel 0 pre-equalization logical-channel 0 power-offset 0 logical-channel 0 ranging-priority 0x0 logical-channel 0 class-id 0x0 no logical-channel 0 shutdown logical-channel 1 prov-attr-mask 0x0 logical-channel 1 channel-width 3200000 logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 no logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 logical-channel 1 shutdown no shutdown interface upstream 4/0.1 frequency 24000000

CASA CMTS

:

channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit no ingress-cancellation logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 1 minislot 2 logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 no logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 logical-channel 1 shutdown no shutdown

interface upstream 4/0.1 frequency 24000000 channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit no ingress-cancellation logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 0 ranging-backoff 0 4 no logical-channel 0 pre-equalization logical-channel 0 power-offset 0 logical-channel 0 ranging-priority 0x0 logical-channel 0 class-id 0x0 no logical-channel 0 shutdown logical-channel 1 prov-attr-mask 0x0 logical-channel 1 channel-width 3200000 logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 no logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 logical-channel 1 shutdown no shutdown

CASA CMTS

interface upstream 4/1.0 frequency 20000000 channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit no ingress-cancellation logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 0 ranging-backoff 0 4 no logical-channel 0 pre-equalization logical-channel 0 power-offset 0 logical-channel 0 ranging-priority 0x0 logical-channel 0 class-id 0x0 no logical-channel 0 shutdown logical-channel 1 prov-attr-mask 0x0 logical-channel 1 channel-width 3200000 logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 no logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 logical-channel 1 shutdown shutdown interface upstream 4/1.1 frequency 20000000 channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit no ingress-cancellation logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 0 ranging-backoff 0 4 no logical-channel 0 pre-equalization logical-channel 0 power-offset 0 logical-channel 0 ranging-priority 0x0 logical-channel 0 class-id 0x0 logical-channel 0 shutdown logical-channel 1 prov-attr-mask 0x0 logical-channel 1 channel-width 3200000 logical-channel 1 profile 2

CASA CMTS

logical-channel 1 minislot 2 logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 no logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 logical-channel 1 shutdown shutdown

CASA-CMTS(config)# show interface upstream 4/0 frequency 20000000 channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit

CASA CMTS

no ingress-cancellation logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 0 ranging-backoff 0 4 no logical-channel 0 pre-equalization logical-channel 0 power-offset 0 logical-channel 0 ranging-priority 0x0 logical-channel 0 class-id 0x0 no logical-channel 0 shutdown logical-channel 1 prov-attr-mask 0x0 logical-channel 1 channel-width 3200000 logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 no logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 logical-channel 1 shutdown no shutdown

C3000-230(config)#show interface upstream 4/0 brief interface upstream 4/0.0 frequency 20000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown no shutdown C3000-230(config)#

C3000-230(config)#show interface upstream 4/0 current interface upstream 4/0.0 frequency 20000000 channel-width 3200000 power-level 0 power-adjustment continue 2 power-adjustment threshold 1 voice-bw-reserve 75 emergency 0 rate-limit no ingress-cancellation logical-channel 0 prov-attr-mask 0x0 logical-channel 0 channel-width 3200000

CASA CMTS

logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 data-backoff automatic logical-channel 0 ranging-backoff 0 4 no logical-channel 0 pre-equalization logical-channel 0 power-offset 0 logical-channel 0 ranging-priority 0x0 logical-channel 0 class-id 0x0 no logical-channel 0 shutdown logical-channel 1 prov-attr-mask 0x0 logical-channel 1 channel-width 3200000 logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 data-backoff automatic logical-channel 1 ranging-backoff 0 4 no logical-channel 1 pre-equalization logical-channel 1 power-offset 0 logical-channel 1 ranging-priority 0x0 logical-channel 1 class-id 0x0 logical-channel 1 shutdown no shutdown C3000-230(config)#

C3000-230(config)#show interface upstream 4/0 stat Interface upstream 4/0.0 statistics Admin status: UP Received 12 broadcasts, 5 multicasts, 23641 unicasts 0 discards, 2472 errors, 0 unknown protocol 87074 Unerrored, 0 Corrected, 0 Uncorrectables Total Modems On This Upstream Channel: 2 ,2 active cm,0 secondary cm Req Mslots 3499886425, Used Req Mslots 71064 Init Mtn Mslots 281230167, Used Init Mtn Mslots 0 Total Mslots 3782191073, Ucast Granted Mslots 1074417 Avg upstream channel utilization: 0 Channel utilization interval: 1 Last clearing of interface stat: never

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# frequency 10000000 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# channel-width 3200000 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config)# upstream map-size 6

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# power-level 10

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# power-adjustment threshold 2 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 1/0)# power-adjustment continue 5

CASA CMTS

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# map-advance dynamic 400 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# no logical-channel 0 shutdown

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 2/6)# logical-channel 0 shutdown

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 data-backoff 2 8

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 data-backoff 0 4

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 ranging-backoff 4 10 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 ranging-backoff 4 10 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 minislot 64

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 class-id 0xFFFFFFFF CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 frame 24 12 64

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 profile 2 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 profile 3 secondaryprofile 12,20,33

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 pre-equalization CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# no logicalchannel 0 pre-equalization CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 prov-attr-mask

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 2/6)#ingress-cancellation 100

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)#voice-bw-reserve 75 emergency 10 CASA-CMTS(config-if-ups 3/6)#

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)#qos bw-reserve 80 CASA-CMTS(config-if-ups 11/0.0)#

Related bandwidth reserve parameters

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)#spectrum-rule 10

CASA CMTS

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# rate-limit

CASA-CMTS(config-if-ups 11/0.0)# no rate-limit

Example: Displaying the utilization rates of upstream channels C3200-232(config-if-ups 11/0.0#show docsis upstream channel utilization Upstream Operational Utilization Online Secondary Channel Slot/Port.Channel Status Percentage Modems Modems Description ----------------------------------------------------------------------------11/0.0 (20000000 Hz) up 0 0 0 11/0.1 (24000000 Hz) up 0 0 0 C3200-232(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config)# show upstream signal-quality upstream port signal noise 11/0.0/1 42.0 11/0.0/1 42.0

CASA-CMTS(config-if-ups 11/0.0)#show upstream 11/0.0 signal-quality upstream channel signal noise 11/0.0/0 0.0 11/0.0/1 0.0 CASA-CMTS(config-if-ups 11/0.0#

CASA CMTS

CASA-CMTS(config)# show upstream burst-noise upstream channel burst noise rate (events/sec) 11/0.0/0 0.0 11/0.0/1 0.0

CASA-CMTS(config-if-ups 11/0.0)#show upstream 11/0.0/0 burstnoise Burst Noise Stats for Channel 11/0.0/0: Burst noise event rate: Percentage of Correctable Burst Events: Percentage of Uncorrectable Burst Events: Burst Duration (microseconds) (in dB) ---------------------------------0 to 1 1 to 3 3 to 10 10 to 50 50 to 500 500 to 2000 2000 to 10000 10000 to 50000 > 50000 C3200-232(config-if-ups 11/0.0)#

0.0 0 % 0 %

events/second.

% of Events

Max Power

-----------

-----------

0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0

CASA CMTS

C10G(config)# show upstream channel set MAC Chan Channel ID Set List 1 1 10/0.0/0 2 1 10/0.1/0 3 1 10/0.2/0 4 1 10/0.3/0 5 1 13/15.0/0 6 1 13/15.1/0 7 1 13/15.2/0 8 1 13/15.3/0

C10G(config)#show upstream channel set | count-only / Count Line: 8 C10G(config)# C10G-CMTS(config-if-ups 5/0.0)#show upstream channel set mac-domain 1 MAC Chan Channel ID Set List 1 1 5/0.0/0 1 2 5/0.1/0 1 256 5/0.0/0, 5/0.1/0 C10G-CMTS(config-if-ups 5/0.0)#

CASA CMTS

C3200-232(config-if-ups 5/0.0)#show cable voice summary Upstream Slot/Port.Channel Normal Emergency Total 5/0.0 0 0 0 5/0.1 0 0 0 5/1.0 0 0 0 5/1.1 0 0 0 5/2.0 0 0 0 5/2.1 0 0 0 5/3.0 0 0 0 5/3.1 0 0 0 5/4.0 0 0 0 5/4.1 0 0 0 5/5.0 0 0 0 5/5.1 0 0 0 5/6.0 0 0 0 5/6.1 0 0 0 5/7.0 0 0 0 5/7.1 0 0 0 total 0 0 0

Configuring IP-bundle interfaces

CASA CMTS

CASA-CMTS(config)# interface ip-bundle 2 CASA-CMTS(ip-bundle 2)#

CASA-CMTS(config)# interface ip-bundle 2 CASA-CMTS(ip-bundle 2)#

CASA-CMTS(ip-bundle 2)# ip address 10.248.1.1 255.255.255.0

CASA CMTS

CASA-CMTS(config)# interface ip-bundle 1.511 CASA-CMTS(ip-bundle 1.155)#

CASA-CMTS(ip-bundle 1.511)# ip address 10.248.4.1 255.255.255.0 secondary

CASA CMTS

CASA-CMTS(config)# interface ip-bundle 1.511 CASA-CMTS(ip-bundle 1.155)#

CASA-CMTS(ip-bundle 1.511)# no ip address 10.248.4.1 255.255.255.0 secondary

CASA-CMTS(config)# interface ip-bundle 1.511 CASA-CMTS(ip-bundle 1.155)#

CASA CMTS

CASA-CMTS(ip-bundle 1.155)# ipv6 address 2000::1000:1/64 secondary CASA-CMTS(ip-bundle 1.155)# no ipv6 address

CASA-CMTS(config)# interface ip-bundle 1.511 CASA-CMTS(ip-bundle 1.155)#

CASA CMTS

CASA-CMTS(ip-bundle 1.155)# ipv6 link-local-address fe80::217:10ff:fe02:cbcd CASA-CMTS(ip-bundle 1.155)# no ipv6 link-local address

CASA-CMTS(config)# interface ip-bundle 1.511 CASA-CMTS(ip-bundle 1.155)# show ipv6 link-localaddress mac domain 1 fe80::217:10ff:fe02:cbcd mac domain 2 fe80::217:10ff:fe02:cbce mac domain 3 fe80::217:10ff:fe02:cbcf mac domain 4 fe80::217:10ff:fe02:cbd0 mac domain 5 fe80::217:10ff:fe02:cbd1 mac domain 6 fe80::217:10ff:fe02:cbd2 mac domain 7 fe80::217:10ff:fe02:cbd3 mac domain 8 fe80::217:10ff:fe02:cbd4 mac domain 9 fe80::217:10ff:fe02:cbd5 mac domain 10 fe80::217:10ff:fe02:cbd6 . . .

CASA CMTS

CASA-CMTS(config)# interface ip-bundle 2 CASA-CMTS(ip-bundle 2)#

CASA-CMTS(ip-bundle 2)# cable helper-address 10.243.6.4 CASA-CMTS(ip-bundle 2)# cable helper-ipv6-address 3000::6 CASA-CMTS(config)#

CASA CMTS

interface ip-bundle 1 ip address 172.18.32.4 255.255.255.0 ip address 192.168.254.254 255.255.255.0 secondary cable helper-address 172.18.4.239 ip access-group 123 interface ip-bundle 1.1 ip address 10.0.0.3 255.255.255.0 ip address 192.168.54.254 255.255.255.0 secondary cable helper-address 172.18.4.239 ip access-group 123 interface ip-bundle 1.2 ip address 192.168.5.1 255.255.255.0 ip address 10.110.50.25 255.255.255.0 secondary cable helper-address 172.18.4.239 ip access-group 123

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# ip bundle 6

CASA CMTS

CASA(config)#cpe-class setTopBoxes CASA(conf-cpe-class stb)#dhcp option 60 stbUser1 CASA(config)#cpe-class computers CASA(conf-cpe-class stb1)#dhcp option 60 pcUser1 CASA(conf-cpe-class stb1)#end CASA(config)#interface ip-bundle 1 CASA(ip-bundle 1)# ip address 10.231.1.1 255.255.255.0 CASA(ip-bundle 1)# ip address 10.231.13.1 255.255.255.0 setTopBoxes CASA(ip-bundle 1)# ip address 10.231.20.1 255.255.255.0 computers CASA(ip-bundle 1)# cable helper-address 192.168.3.16 setTopBoxes CASA(ip-bundle 1)# cable helper-address 192.168.3.17 computers CASA(ip-bundle 1)# cable helper-address 192.168.3.6

string

CASA CMTS

string

CASA-CMTS(config)# cpe-class computers CASA-CMTS(conf-cpe-class computers)#

string

CASA-CMTS(config-if-mac 2)# ip bundle 6

CASA-CMTS(config)# interface ip-bundle 1 CASA-CMTS(ip-bundle 1)#

CASA-CMTS(ip-bundle 1)# # ip rip authentication key-chain school CASA-CMTS(ip-bundle 1)# no ip rip authentication key-chain

CASA CMTS

CASA-CMTS(config)# interface ip-bundle 1 CASA-CMTS(ip-bundle 1)#

CASA-CMTS(ip-bundle 1)# ip rip authentication string public CASA-CMTS(ip-bundle 1)# no ip rip authentication string

CASA-CMTS(config)# interface ip-bundle 1 CASA-CMTS(ip-bundle 1)#

CASA CMTS

CASA-CMTS(config-if-gige 0)# ip rip authentication mode md5 auth-length rfc

CASA-CMTS(config)# show interface ip-bundle ip address 10.232.1.1 255.255.255.0 ip address 10.232.10.1 255.255.255.0 secondary ip address 10.232.11.1 255.255.255.0 secondary ipv6 address 2000:232:1::1/60 ipv6 address 2000:232:2::1/60 secondary cable helper-address 192.168.3.6 cable helper-ipv6-address 3000::10 CASA-CMTS(config)# show interface ip-bundle 1 stat ip-bundle: upstream bytes: upstream packets:

1 144574 2118

CASA CMTS

downstream downstream downstream downstream downstream downstream

unicast bytes: multicast bytes: total bytes: unicast packets: multicast packets: total packets:

96070 0 96070 446 0 446

CASA-CMTS(config)# show interface ip-bundle throughput ip-bundle: 1 upstream: 0 kbps upstream: 0 packet/second downstream: 0 kbps downstream: 0 packet/second

Configuring DOCSIS MAC domains

CASA CMTS

CASA-CMTS# show interface docsis-mac interface docsis-mac 1 no shutdown sync-interval 10 insertion-interval 20 ucd-interval 1000 no dhcp-authorization invited-ranging-attempts 16 ip-provisioning-mode ipv4-only no early-authentication-encryption no extended-upstream-frequency-range cm-status event report multicast-dsid-forward downstream channel bonding upstream channel bonding no tftp-proxy

CASA CMTS

no upstream drop classifier no send udc rules no dhcp-giaddr-primary mdd interval 2000 sid-cluster max-requests 0 sid-cluster max-outstanding-bytes 0 sid-cluster max-total-bytes 0 sid-cluster max-time 0 max sid-cluster per-service-flow 2 ip bundle 1 downstream 1 interface qam 2/0/0 downstream 2 interface qam 2/0/1 downstream 3 interface qam 2/0/2 downstream 4 interface qam 2/0/3 upstream 1 interface upstream 1/0.0/0 upstream 2 interface upstream 1/0.1/0 upstream 3 interface upstream 1/7.0/0 upstream 4 interface upstream 1/7.1/0 mgmd ipv4 query-interval 125 mgmd ipv4 version 3 mgmd ipv4 max-query-response-time 100 mgmd ipv4 proxy-interface gige 0 mgmd ipv4 robustness 2 mgmd ipv4 last-member-query-interval 10 mgmd ipv4 shutdown mgmd ipv6 query-interval 125 mgmd ipv6 version 2 mgmd ipv6 max-query-response-time 100 mgmd ipv6 proxy-interface gige 0 mgmd ipv6 robustness 2 mgmd ipv6 last-member-query-interval 10 mgmd ipv6 shutdown privacy kek life-time 604800 privacy tek life-time 43200

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)# end

CASA CMTS

CASA-CMTS(config)# CASA-CMTS(config)# no interface docsis-mac 2

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# ip bundle 6

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# upstream 5 interface upstream 1/1/0

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# no upstream 5

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# downstream 3 interface qam 0/2/1

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# downstream 3 interface qam 0/2/1 secondary

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# no downstream 3

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# no shutdown

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# shutdown

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# ip address 192.168.3.211 255.255.255.0 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA-CMTS(config-if-mac 2)# ipv6 address 2000::1000:1/64

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# no ipv6 address

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# helper-address 172.23.66.44 CASA-CMTS(config-if-mac 2)# end CASA-CMTS(config)#

CASA-CMTS(config-if-mac 2)# 172.23.66.143 host CASA-CMTS(config-if-mac 2)# 172.23.66.144 cable-modem CASA-CMTS(config-if-mac 2)# 172.23.66.145 mta CASA-CMTS(config-if-mac 2)# CASA-CMTS(config)#

helper-address helper-address helper-address end

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# ip bundle 1

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# sync-interval 100 CASA-CMTS(config-if-mac 2)# end

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)#initial-tech broadcastranging

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# insertion-interval 10

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA-CMTS(config-if-mac 2)# mdd interval 10 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# dhcp-giaddr-primary

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)#tftp-proxy

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA-CMTS(config-if-mac 2)#tftp-enforce

CASA-CMTS(config)# show cable modem tftp-bypass MAC Address IP Address US DS MAC Prim RxPwr Timing Num BPI Intf Intf Status Sid (dB) Offset CPEs Enb total cm 0

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# no mgmd ipv4 shutdown CASA-CMTS(config-if-mac 2)# CASA-CMTS(config-if-mac 2)# mgmd ipv4 shutdown CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# dhcp-authorization CASA-CMTS(config-if-mac 2)# no dhcpauthorization

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA-CMTS(config-if-mac 2)# upstream channel bonding CASA-CMTS(config-if-mac 2)# no upstream channel bonding

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# multicast-dsidforward

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# ip-provisioningmode dual-stack

CASA CMTS

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA CMTS

CASA-CMTS(config-if-mac 1)# router-advertisement enable CASA-CMTS(config-if-mac 1)# router-advertisement other-config-flag false

CASA-CMTS# show router-advertisement router advert table, domain=22 SendAdverts=1 MaxInterval=600 MinInterval=200 ManagedFlag=1 OtherConfigFlag=1 LinkMTU=1500 ReachableTime=0 RetransmitTime=0 CurrHopLimit=64 DefaultLifetime=1800 RowStatus=1 Prefix_flag = 1

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA CMTS

CASA-CMTS(config-if-mac 1)# privacy tek lifetime 300 CASA-CMTS(config-if-mac 1)#

CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)#

CASA-CMTS(config-if-mac 2)# cm trap CASA-CMTS(config-if-mac 2)# cm trap interval 20000

CASA CMTS

CASA-CMTS# show interface docsis-mac 8

CASA-CMTS# show interface docsis-mac stat Interface docsis-mac 1 statistics Ifindex: 77 Administrated status: UP Operation status: UP Mac address: 0017.1000.2647 DSA Request : 0/ups; DSA Response : 0/ups; DSA Acknowledgements : 0/ups; DSA Success : 0/ups; DsA Fail : 0/ups; DSC Request : 0/ups; DSC Response : 0/ups; DSC Acknowledgements : 0/ups; DSC Success : 0/ups; DSC Fail : 0/ups; DSD Request : 0/ups; DSD Response : 0/ups; DSD Success : 0/ups;

0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds

CASA CMTS

DSD DCC DCC DCC DCC DCC DCC DCC DBC DBC DBC DBC DBC DBC

Fail Request Response Acknowledgements Success Fail RSP Depart RSP Arrive Request Response Acknowledgements Success Fail Partial Service

: : : : : : : : : : : : : :

Configuring service groups

0/ups; 0/ups; 2/ups; 0/ups; 0/ups; 0/ups; 1/ups; 1/ups; 0/ups; 0/ups; 0/ups; 0/ups; 0/ups; 0/ups;

0/ds 1/ds 0/ds 1/ds 1/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds 0/ds

CASA CMTS

CASA-CMTS(config)# service group 2 CASA-CMTS(conf-svc-grp 2)# end CASA-CMTS(config)#

CASA-CMTS(config)# no service group 2 CASA-CMTS(conf-svc-grp 2)# end CASA-CMTS(config)#

CASA-CMTS(config)# service group 2

CASA-CMTS(conf-svc-grp 2)# upstream 1/1.0 CASA-CMTS(conf-svc-grp 2)# no upstream 1/1.0

CASA CMTS

CASA-CMTS(conf-svc-grp 2)# qam 0/2/1 CASA-CMTS(conf-svc-grp 2)# no qam 0/2/1

CASA CMTS

CASA-CMTS(config)# show service group 1 service group 1 qam 0/1/0 qam 0/1/1 qam 0/1/2 qam 0/1/3 upstream 3/0.0 upstream 3/1.0 upstream 3/2.0 upstream 3/3.0

CASA-CMTS(config)#service group 4 C10G-CMTS(conf-svc-grp 4)#show this service group 4 upstream 11/6.0 upstream 11/6.1 upstream 11/6.2 upstream 11/6.3 upstream 11/7.0 upstream 11/7.1 upstream 11/7.2 upstream 11/7.3

CASA CMTS

CASA-CMTS(config)#show md-ds-sg docsis-mac 1 service-group 1 qam 0/1/0 qam 0/1/1 qam 0/1/2 qam 0/1/3 docsis-mac 1 service-group 2 qam 0/2/0 qam 0/2/1 qam 0/2/2 qam 0/2/3

CASA-CMTS#show md-ds-sg mac 1 service-group 1 docsis-mac 1 service-group 1 qam 0/2/0 qam 0/2/1 qam 0/2/2 qam 0/2/3

CASA CMTS

CASA-CMTS#show md-ds-sg service-group 1 docsis-mac 1 service-group 1 qam 0/2/0 qam 0/2/1 qam 0/2/2 qam 0/2/3

CASA-CMTS#show md-us-sg mac 1 service-group 1 docsis-mac 1 service-group 1 upstream 1/4/0 upstream 1/5/0 upstream 1/6/0 upstream 1/7/0

Configuring bonding groups

CASA CMTS

CASA-CMTS(config)# bonding-group downstream mac-domain 1 group-id 1 CASA-CMTS(bond-ds-mac-1-group-1)#

CASA-CMTS(config)# no bonding-group downstream mac-domain 1 group-id 1 CASA-CMTS(bond-ds-mac-1-group-1)#

CASA CMTS

CASA-CMTS(config)# bonding-group upstream macdomain 1 group-id 1 CASA-CMTS(bond-ds-mac-1-group-1)#

CASA-CMTS(config)# no bonding-group upstream mac-domain 1 group-id 1 CASA-CMTS(bond-ds-mac-1-group-1)#

CASA-CMTS(config)# bonding-group upstream macdomain 1 group-id 1 CASA-CMTS(bond-ds-mac-1-group-1)#

CASA CMTS

CASA-CMTS(bond-us-mac-1group-1)# upstream 1/1.0/0 CASA-CMTS(bond-us-mac-1group-1)# no upstream 1/1.0/0

CASA-CMTS(config)# bonding-group downstream mac-domain 1 group-id 1 CASA-CMTS(bond-ds-mac-1-group-1)#

CASA-CMTS(bond-ds-mac-1-group-1)# qam 0/2/1 CASA-CMTS(bond-ds-mac-1-group-1)# no qam 0/2/1

CASA CMTS

CASA-CMTS# show bonding-group mac-domain bonding-group downstream mac-domain 1 group-id 1 qam 0/1/0 qam 0/1/1 qam 0/1/2 qam 0/1/3 bonding-group upstream mac-domain 1 group-id 1 upstream 3/0/0 upstream 3/1/0 upstream 3/2/0 upstream 3/3/0

CASA-CMTS(config)# rcc mac 1 rcp-id 10:00:00:00:01 1 CASA-CMTS(conf-mac 1 rcc 1)#

CASA CMTS

CASA-CMTS(config)# rcc mac 1 rcp-id 10:00:00:00:01 1 CASA-CMTS(conf-mac 1 rcc 1)#

CASA-CMTS(conf-mac 1 rcc 1)# rm 1 frequency 549000000 connect 0

CASA CMTS

CASA-CMTS(config)# rcc mac 1 rcp-id 10:00:00:00:01 1 CASA-CMTS(conf-mac 1 rcc 1)#

CASA-CMTS(conf-mac 1 rcc 1)# rc 1 downstream 1 primary connect 1

CASA CMTS

CASA-CMTS# show rcc mac 1 rcc mac 1 rcp-id 10:00:00:00:01 1 vendor-specific spacing6 rcc-desc spacing=6; rc 1 downstream 1 primary connect 1 rc 2 downstream 2 primary connect 1 rc 3 downstream 3 primary connect 1 rc 4 downstream 4 primary connect 1 rm 1 frequency 549000000 connect 0

Configuring modulation profiles

CASA CMTS

CASA CMTS

CASA CMTS

Auto-mode TDMA-type modulation profile configuration

CASA-CMTS(config)#modulation profile 22 tdma qpsk CASA-CMTS(config-mod-prof)#

Manual mode TDMA-type modulation profile configuration

profile

profile

CASA CMTS

CASA-CMTS(config)#modulation-profile 22 CASA-CMTS(config-mod-prof)#

iuc mod-type diff-encoding preamble-len fec-t fec-k scrambler-seed max-burst-size guard-time code-word-len scrambler-mode

Configuring modulation-profile 6 CASA-CMTS# config CASA-CMTS(config)# modulation-profile 6 CASA-CMTS(config-mod-prof)# request tdma qpsk off 64 0 16 338 1 8 fixed on CASA-CMTS(config-mod-prof)# initial tdma qpsk off 128 5 34 338 0 48 fixed on CASA-CMTS(config-mod-prof)# station tdma qpsk off 128 5 34 338 0 48 fixed on CASA-CMTS(config-mod-prof)# short tdma qpsk off 72 6 75 338 6 8 fixed on CASA-CMTS(config-mod-prof)# long tdma qpsk off 80 8 220 338 0 8 fixed on CASA-CMTS(config-mod-prof)# end CASA-CMTS(config)#

iuc mod-type diff-encoding preamble-len fec-t fec-k scrambler-seed max-burst-size guard-time code-word-len scrambler-mode

CASA CMTS

Auto-mode ATDMA-type modulation profile configuration

profile

mod-type

profile mod-type

CASA-CMTS(config)#modulation profile 22 atdma qpsk CASA-CMTS(config-mod-prof)#

Manual mode ATDMA-type modulation profile configuration

CASA-CMTS(config)#modulation profile 22 CASA-CMTS(config-mod-prof)#

CASA CMTS

iuc mod-type diff-encoding preamble-len fec-t fec-k scrambler-seed max-burst-size guard-time code-word-len scrambler-mode intlv-depth intlv-block preamble-type

Configure modulation-profile 7 CASA-CMTS# config CASA-CMTS(config)# modulation-profile 7 CASA-CMTS(config-mod-prof)# request atdma qpsk 1536 qpsk0 CASA-CMTS(config-mod-prof)# initial atdma qpsk 1536 qpsk0 CASA-CMTS(config-mod-prof)# station atdma qpsk 1536 qpsk0 CASA-CMTS(config-mod-prof)# a-shot atdma 16qam 1536 qpsk0 CASA-CMTS(config-mod-prof)# a-long atdma 16qam 1536 qpsk0 CASA-CMTS(config-mod-prof)# end CASA-CMTS(config)#

= T = k

off 64 0 16 338 1 8 fixed on 1 off 128 5 34 338 0 48 fixed on 1 off 128 5 34 338 0 48 fixed on 1 off 72 6 75 338 6 8 fixed on 1 off 80 8 220 338 0 8 fixed on 1

CASA CMTS

profile

mod-type



CASA-CMTS(config)#modulation-profile 22 mtdma qpsk CASA-CMTS(config-mod-prof)#

CASA CMTS

CASA-CMTS(config)#modulation-profile 22 CASA-CMTS(config-mod-prof)#

= T = k

Configuring modulation-profile 8 CASA-CMTS# config CASA-CMTS(config)# modulation-profile 8 CASA-CMTS(config-mod-prof)# request mtdma qpsk off 64 0 16 338 1 8 fixed on 1 1536 qpsk0 CASA-CMTS(config-mod-prof)# initial mtdma qpsk off 128 5 34 338 0 48 fixed on 1 1536 qpsk0 CASA-CMTS(config-mod-prof)# station mtdma qpsk off 128 5 34 338 0 48 fixed on 1 1536 qpsk0 CASA-CMTS(config-mod-prof)# shot mtdma 16qam off 72 6 75 338 6 8 fixed on 1 1536 qpsk0 CASA-CMTS(config-mod-prof)# long mtdma 16qam off 80 8 220 338 0 8 fixed on 1 1536 qpsk0 CASA-CMTS(config-mod-prof)# a-shot mtdma 16qam off 72 6 75 338 6 8 fixed on 1 1536 qpsk0 CASA-CMTS(config-mod-prof)# a-long mtdma 16qam off 80 8 220 338 0 8 fixed on 1 1536 qpsk0 CASA-CMTS(config-mod-prof)# end CASA-CMTS(config)#

CASA CMTS

= T = k



CASA-CMTS(config)#modulation-profile 22 scdma qpsk CASA-CMTS(config-mod-prof)#

CASA CMTS

[]

Example: show modulation-profile, all profiles CASA-CMTS# config CASA-CMTS(config)# show modulation-profile modulation-profile 1 request tdma qpsk off 64 0 16 338 0 16 fixed on initial tdma qpsk off 640 5 34 338 0 48 fixed on station tdma qpsk off 384 5 34 338 0 48 fixed on short tdma qpsk off 84 6 75 338 13 8 shortened on long tdma qpsk off 96 8 220 338 0 8 shortened on modulation-profile 2 request tdma qpsk off 64 0 16 338 0 16 fixed on initial tdma qpsk off 640 5 34 338 0 48 fixed on station tdma qpsk off 384 5 34 338 0 48 fixed on short tdma 16qam off 168 6 75 338 7 8 shortened on long tdma 16qam off 192 8 220 338 0 8 shortened on modulation-profile 3 request atdma qpsk off 64 0 16 338 0 16 fixed on 1 1536 qpsk0 initial atdma qpsk off 640 5 34 338 0 48 fixed on 1 1536 qpsk0 station atdma qpsk off 384 5 34 338 0 48 fixed on 1 1536 qpsk0 a-short atdma 64qam off 104 12 75 338 6 8 shortened on 1 1536 qpsk1 a-long atdma 64qam off 104 16 220 338 0 8 shortened on 1 1536 qpsk1 modulation-profile 4 request mtdma qpsk off 64 0 16 338 0 16 fixed on 1 1536 qpsk0 initial mtdma qpsk off 640 5 34 338 0 48 fixed on 1 1536 qpsk0 station mtdma qpsk off 384 5 34 338 0 48 fixed on 1 1536 qpsk0 short mtdma 16qam off 168 6 75 338 7 8 shortened on 1 1536 qpsk1 long mtdma 16qam off 192 8 220 338 0 8 shortened on 1 1536 qpsk1 a-short mtdma 64qam off 104 12 75 338 6 8 shortened on 1 1536 qpsk1 a-long mtdma 64qam off 104 16 220 338 0 8 shortened on 1 1536 qpsk1 modulation-profile 5 request scdma qpsk off 64 0 16 338 1 0 fixed on qpsk0 on 2 1 initial scdma qpsk off 640 5 34 338 0 0 fixed on qpsk0 off 2 station scdma qpsk off 512 5 34 338 0 0 fixed on qpsk0 off 2 a-short scdma 128qam off 64 5 33 338 12 0 shortened on qpsk0 a-long scdma 128qam off 64 10 156 338 0 0 shortened on qpsk0

off 1 off 1 off on 128 1 on on 128 1 on

CASA CMTS

show modulation-profile, one profile CASA-CMTS# config CASA-CMTS(config)# show modulation-profile 1 modulation-profile 1 request tdma qpsk off 64 0 16 338 0 16 fixed on initial tdma qpsk off 640 5 34 338 0 48 fixed on station tdma qpsk off 384 5 34 338 0 48 fixed on short tdma qpsk off 84 6 75 338 13 8 shortened on long tdma qpsk off 96 8 220 338 0 8 shortened on



CASA-CMTS(config)# no modulation-profile 7 CASA-CMTS(config)#

CASA CMTS

Examples C10G(config-if-ups 13/0.0)# show upstream burst-noise upstream channel burst noise rate (events/sec) 10/0.0/0 143.0 10/0.0/1 119.7 10/0.1/0 95.2 10/0.1/1 131.1 10/1.0/0 0.0 10/1.0/1 0.0 10/1.1/0 0.0 10/1.1/1 0.0 C10G-181(config-if-ups 13/0.0)#show upstream 10/0.0/0 burst-noise Burst Noise Stats for Channel 10/0.0/0: Burst noise event rate: Percentage of Correctable Burst Events: Percentage of Uncorrectable Burst Events: Burst Duration (microseconds) ----------------------------0 to 1 1 to 3 3 to 10 10 to 50 50 to 500 500 to 2000 2000 to 10000 10000 to 50000 > 50000

% of Events ----------0 65 35 0 0 0 0 0 0

Configuring multicast operations

143.5 events/second. 98% 2% Max Power (in dB) ----------------0 0 0 0 0 0 0 0 0

CASA CMTS

CASA CMTS

CASA-CMTS(config)# multicast max channel-util 70

CASA-CMTS(config)# multicast authorization enable

CASA-CMTS(config)# no multicast authorization enable

CASA-CMTS(config)# multicast single-said

CASA CMTS

CASA-CMTS(config)# multicast authorization profile my-profile

CASA-CMTS(config)# multicast authorization profile my-profile CASA-CMTS(conf-auth-profile my-profile)#

CASA CMTS

CASA-CMTS(conf-auth-profile my-profile)# sessionrule 1 accept 192.168.2.1/24 224.0.100.1/24 priority 1

CASA-CMTS(config)# multicast authorization default-action permit

CASA CMTS

CASA-CMTS(config)# multicast authorization maxsession-num 5

CASA-CMTS(config)# multicast authorization matchprofile my-profile1 CASA-CMTS(config)# multicast authorization matchprofile my-profile2

CASA-CMTS(config)#show running-config | include multicast !multicast

CASA CMTS

multicast authorization enable multicast authorization match-profile my-profile1 multicast authorization default-action permit multicast authorization max-session-num 5 multicast authorization profile 1 multicast group config 1 multicast group config 2 multicast group encryption 1 algorithm cmts multicast group qos 1 IPTV aggregate max-sess 10 app-id 1234 multicast-dsid-forward

CASA-CMTS(config)#show igmp client Number Module Vlan Multicast ------ ----------------IPV6 Multicast Groups: Number Module Vlan Multicast ------ -----------------

Group ----Group -----

CASA-CMTS(config)# multicast group config 1 CASA-CMTS(conf-grp-config 1)#

CASA CMTS

CASA-CMTS(conf-grp-config 1)# source-address 192.168.0.1/32 CASA-CMTS(conf-grp-config 1)# group-address

CASA CMTS

244.0.0.1/32 CASA-CMTS(conf-grp-config CASA-CMTS(conf-grp-config CASA-CMTS(conf-grp-config CASA-CMTS(conf-grp-config CASA-CMTS(conf-grp-config CASA-CMTS(conf-grp-config CASA-CMTS(conf-grp-config

1)# 1)# 1)# 1)# 1)# 1)# 1)#

tos-low 0 tos-high 0 tos-mask 0 qos-id 13 encryption-id 0 phs-id 0 priority 1

CASA-CMTS(config)# multicast group encryption 1 algorithm cmts

CASA CMTS

CASA-CMTS(config)# multicast group qos 13 mysrvs-class single app-id 1

CASA-CMTS(config)# cable service class 1 CASA-CMTS(conf-service-class 1)#

CASA CMTS

CASA CMTS

CASA-CMTS(config)# cable service-class 1 CASA-CMTS(conf-service-class 1)# name my_srvs_class CASA-CMTS(conf-service-class 1)# min-packet-size 100 CASA-CMTS(conf-service-class 1)# min-reserve-rate 200 CASA-CMTS(conf-service-class 1)# max-concat-burst 123 CASA-CMTS(conf-service-class 1)# max-latency 112 CASA-CMTS(conf-service-class 1)# max-traffic-burst 10 CASA-CMTS(conf-service-class 1)# max-traffic-rate 13

CASA-CMTS(config)# multicast default grp-serviceclass dgsc1

CASA-CMTS(config)#show running-config | include multicast !multicast multicast authorization enable multicast authorization match-profile my-profile1

CASA CMTS

multicast authorization default-action permit multicast authorization max-session-num 5 multicast authorization profile 1 multicast group config 1 multicast group config 2 multicast group encryption 1 algorithm cmts multicast group qos 1 IPTV aggregate max-sess 10 app-id 1234 multicast-dsid-forward

CASA-CMTS(config)# cable igmp static-group 224.0.100.100

CASA-CMTS(config)# cable igmp static-group 224.0.100.100 source 192.168.0.1 CASA-CMTS(conf-igmp-static-group 224.0.100.100)#

CASA CMTS

CASA-CMTS(conf-igmp-static-group 224.0.100.100)# qam 2/0/0

CASA-CMTS(config)# cable igmp static-group 224.0.100.100 source 192.168.0.1 CASA-CMTS(conf-igmp-static-group 224.0.100.100)#

CASA-CMTS(conf-igmp-static-group 224.0.100.100)# qam 2/0/0

CASA CMTS

CASA-CMTS(config)# cable igmp static-group 224.0.100.100 source 192.168.0.1 CASA-CMTS(conf-igmp-static-group 224.0.100.100)#

CASA-CMTS(conf-igmp-static-group 224.0.100.100)# secondary-source 224.0.100.200

CASA-CMTS(conf-igmp-static-group 224.0.100.100)# switch multicast-source

CASA CMTS

CASA-CMTS(config)# no cable igmp static-group

CASA-CMTS(config)# no cable igmp static-group 224.0.100.100

CASA-CMTS(config)# no cable igmp static-group 224.0.100.100 source 192.168.0.1

CASA CMTS

CASA-CMTS(config)# show running-config | include igmp …… cable igmp static-group 224.0.100.1 qam 2/0/0

CASA-CMTS(config)# cable igmp filter 10 2

CASA-C3000(config)#show cable filter runningconfig cable arp filter 8 2 cable source-verify leasequery-filter 32 10 cable icmp filter 0 2 cable igmp filter 4 2 CASA-C3000(config)#

CASA CMTS

CASA-CMTS(config)# multicast group config 1 CASA-CMTS(conf-grp-config 1) source-address 0.0.0.0/0 CASA-CMTS(conf-grp-config 1) group-address 230.0.1.0/24 CASA-CMTS(conf-grp-config 1) qos-id 1 CASA-CMTS(conf-grp-config 1) end CASA-CMTS(config) multicast group qos 1 IPTV aggregate max-sess 10 appid 1 CASA-CMTS(config) application policy 1234 CASA-CMTS(conf-app-policy 1234) limit replication CASA-CMTS(conf-app-policy 1234) max iptv channel

CASA CMTS

Enabling MLD on an interface

C3200-232(config)# interface gige 5 C3200-232(config-if-gige 5)# ipv6 mld

Configuring cable service classes

CASA-CMTS(config)# cable service-class 1 CASA-CMTS(conf-service-class 1)#

CASA CMTS

CASA-CMTS(conf-service-class 1)# name my_class

CASA-CMTS(conf-service-class 1)# upstream

param

CASA CMTS

CASA-CMTS(conf-service-class 1)#max-traffic-burst 20000000

CASA CMTS

CASA-CMTS(conf-service-class 1)#end CASA-CMTS(config)#show cable service-class Index Name Dir Sched Prio MaxSusRate MaxBurst MinRsvRate 1 test US BE 0 20000000 0

0

CASA CMTS

CASA-CMTS(config)#show cable service-class Index Name Dir Sched Prio MaxSusRate MaxBurst MinRsvRate 1 PCMM-US US BE 0 0 24480 0 2 PCMM-DS DS BE 0 512000 3044 0 3 DefD3Down US BE 0 0 3044 0

CASA-CMTS(config)#show cable service-class 1 verbose Index: 1 Name: UP_UGS Direction: Upstream/Downstream Traffic Priority: 0 Maximum Sustained Rate: 0 bits/sec Max Burst: 1522 bytes Minimum Reserved Rate: 0 bits/sec Minimum Packet Size 100 bytes Admitted QoS Timeout 200 seconds Active QoS Timeout 30 seconds Scheduling Type: Unsolicited Grant Service Request/Transmission Policy: 0x1FF Unsolicited Grant Size: 100 bytes Nominal Grant Interval: 20000 usecs Tolerated Grant Jitter: 4000 usecs Grants per Interval: 1 IP ToS Overwrite [AND-mask,OR-mask]: 0xE0,0xA0 Max Latency: 0 usecs Parameter Presence Bitfield: {0xE08, 0xBCC000}

CASA CMTS

Example: Service class configuration CASA-CMTS(config)#cable service-class 1 CASA-CMTS(conf-service-class 1)# name PCMM-US CASA-CMTS(conf-service-class 1)# max-traffic-burst 24480 CASA-CMTS(conf-service-class 1)# min-packet-size 0 CASA-CMTS(conf-service-class 1)# max-concat-burst 24480 CASA-CMTS(conf-service-class 1)# req-trans-policy 0x0 CASA-CMTS(conf-service-class 1)# tos-overwrite 0xFF 0x0 CASA-CMTS(conf-service-class 1)# app-id 0 CASA-CMTS(conf-service-class 1)# CASA-CMTS(config)#cable service-class 2 CASA-CMTS(conf-service-class 2)# name PCMM-DS CASA-CMTS(conf-service-class 2)# max-traffic-rate 512000 CASA-CMTS(conf-service-class 2)# min-packet-size 0 CASA-CMTS(conf-service-class 2)# req-trans-policy 0x0 CASA-CMTS(conf-service-class 2)# tos-overwrite 0xFF 0x0 CASA-CMTS(conf-service-class 2)# downstream CASA-CMTS(conf-service-class 2)# app-id 0 CASA-CMTS(conf-service-class 2)# CASA-CMTS(config)#cable service-class 3 CASA-CMTS(conf-service-class 3)# name DefD3Down CASA-CMTS(conf-service-class 3)# min-packet-size 0 CASA-CMTS(conf-service-class 3)# req-trans-policy 0x0

CASA CMTS

CASA-CMTS(conf-service-class 3)# tos-overwrite 0xFF 0x0 CASA-CMTS(conf-service-class 3)# app-id 0 CASA-CMTS(conf-service-class 3)#end CASA-CMTS(config)#end CASA-CMTS#show cable service-class Index 1 2 3

Name Dir PCMM-US US PCMM-DS DS DefD3Down

Sched BE BE US

Configuring PacketCable

Prio 0 0 BE

MaxSusRate 0 512000 0

MaxBurst 24480 3044 3044

MinRsvRate 0 0 0

CASA CMTS

CASA-CMTS(config)# packetcable

CASA-CMTS(config)# show packetcable log

CASA-CMTS(config)# packetcable dscp check

CASA CMTS

CASA-CMTS(config)# packetcable elemid 9996

CASA-CMTS(config)# packetcable myaddress 1.1.1.1

CASA-CMTS(config)# packetcable ftp newuser abcd

CASA CMTS

CASA-CMTS(config)# packetcable ftp user password mypswd

CASA-CMTS(config)# packetcable t0 15

CASA-CMTS(config)# packetcable t1 10

CASA CMTS

CASA-CMTS(config)# CASA-CMTS(config)# interface loopback CASA-CMTS(config)# alpha

packetcable nls cpd packetcable nls source10 packetcable nsl agid 124 key

CASA-CMTS(config)# packetcable max normal call 5

CASA CMTS

CASA-CMTS(config)# packetcable max emerg call 100

CASA-CMTS(config)# packetcable inactive call aging 4 minimum traffic 50

CASA CMTS

CASA-CMTS(config)#cable admission-control preempt priority-voice

CASA-CMTS(config)# packetcable multimedia CASA-CMTS(config)# packetcable multimedia t1 100

CASA CMTS

casa-CMTS(config)#pcmm mmversion major 1 minor 10 casa-CMTS(config)# casa-CMTS(config)#no pcmm mmversion major 1 minor 10

casa-CMTS(config)#show pcmm gateid 1 clsfy spec Cable Modem: 0015.f2fe.8d6a GateID: 0x40002 PCMM gate state: AUTH Direction: upstream Type: multicast PCMM service-flow: 0 PCMM T1 timer: 200s PCMM T2 timer: 0s PCMM T3 timer: 60s PCMM T4 timer: 0s PCMM classify count: 1 PCMM traffic profile type: 1 PCMM traffic profile: Flow Spec PCMM envelope type: 1 PCMM Time Usage Limit: 0s PCMM Time Usage: 0s PCMM Volume Usage Limit: 0 Kbytes PCMM Volume Usage: 0 Kbytes casa-CMTS(config)#show pcmm gateid 5 spec casa-CMTS(config)#show pcmm gateid 1 traffic spec

CASA CMTS

CASA-CMTS(config)# cable service-flow activetimeout 100

CASA-CMTS(config)# cable dynamic service-flow primary

CASA CMTS

casa-CMTS(config)#show pcmm ps server IP Port PSID

casa-CMTS(config)#show pcmm multicast GateID SubscriberID Multicast-Session SharedResourceID

CASA-CMTS(config)# show packetcable global **********PacketCable Global********** PacketCable: enable Element ID: 9999 MyIPaddr: 0.0.0.0 Gate ID Used: 0 Max Gate: 8000 COPS Server Listen Port: 2126 RKS_Receive_Port: 1813 PCMM Listen Port : 3918 PCMM version: 2.0 T0 Timer: 30 T1 Timer: 200 Max Batch File Size: 65535 Batch File Send Mode: UDP Batch File Send Time: 1

CASA CMTS

Batch File Ftp User: casa Normal Calls: 0 Emerg Calls: 0 Max Normal Calls: 1000 Max Emerg Calls: 1000 RKS tries: 3 Media Alive: 00:00 inactive call aging: 2 inactive call mini traffic: 30 no cable admission-control preempt priority-voice **************************************

CASA-CMTS(config)# packetcable rks timeout 9 CASA-CMTS(config)# no packetcable rks timeout

CASA-CMTS(config)# packetcable rks retry 6 CASA-CMTS(config)# no packetcable rks retry

CASA CMTS

CASA-CMTS(config)# packetcable rks batchfile sendmode udp CASA-CMTS(config)# no packetcable rks batchfile sendmode

CASA-CMTS(config)# packetcable rks batchfile time 120 CASA-CMTS(config)# no packetcable rks batchfile time

CASA CMTS

CASA-CMTS(config)# packetcable rks batchfile max size 4096 CASA-CMTS(config)# no packetcable rks batchfile max size

CASA-CMTS(config)# packetcable rks batchfile max msg 10 CASA-CMTS(config)# no packetcable rks batchfile max msg

CASA CMTS

CASA-CMTS(config)# packetcable media alive time 10:30 CASA-CMTS(config)# no packetcable media alive

CASA-CMTS(config)# packetcable max gate 1000 CASA-CMTS(config)# no packetcable max gate

CASA-CMTS(config)# show packetcable rks server

CASA CMTS

CASA-CMTS(config)# show packetcable gate GateID SubID State U_stream D_stream RKSIP 1 10.237.2.200 committed enable enable 192.168.0.155

CASA-CMTS(config)# show packetcable gateid 1 uspec

CASA-CMTS(config)# show packetcable commit gate

CASA CMTS

CASA-CMTS(config)# show packetcable cms server

Configuring DSG

CASA-CMTS(config)# dsg tunnel 2 CASA-CMTS(conf-dsg-tunnel-2)# end CASA-CMTS(config)#

CASA CMTS

CASA-CMTS(config)# no dsg tunnel 2

CASA-CMTS(config)# no dsg tunnel-group 2

CASA-CMTS(config)# dsg tunnel-group 2 CASA-CMTS(conf-dsg-tunnel-grp 2)# CASA-CMTS(config)# no dsg tunnel 2

CASA CMTS

CASA-CMTS(conf-dsg-tunnel-2)# group 3 CASA-CMTS(conf-dsg-tunnel-2)# no group 3

CASA-CMTS(config)# show dsg tunnel-group 2 channel 1 qam x/y/z rule-priority 20 vendorparam-id 1 ucid-list 1 channel 2 qam x/y/z rule-priority 30 vendorparam-id 500 ucid-list 2

CASA-CMTS(conf-dsg-tunnel-grp-2)# end

CASA CMTS

CASA-CMTS(config)# dsg tunnel 2 CASA-CMTS(conf-dsg-tunnel-2)# CASA-CMTS(conf-dsg-tunnel-id)# end CASA-CMTS(config)# CASA-CMTS(config)# no dsg tunnel 2

CASA-CMTS(conf-dsg-tunnel-2)# dst-address 1234.2345.3456

CASA-CMTS(config)# dsg tunnel 2 CASA-CMTS(conf-dsg-tunnel-2)# CASA-CMTS(conf-dsg-tunnel-id)# end CASA-CMTS(config)#

CASA CMTS

CASA-CMTS(config)# no dsg tunnel 2

CASA-CMTS(conf-dsg-tunnel-2)# client-list 123 CASA-CMTS(conf-dsg-tunnel-2)# no client-list 123

CASA-CMTS(config)# dsg tunnel 2 CASA-CMTS(conf-dsg-tunnel-2)# CASA-CMTS(conf-dsg-tunnel-id)# end CASA-CMTS(config)# CASA-CMTS(config)# no dsg tunnel 2

CASA-CMTS(conf-dsg-tunnel-2)# service-class private-class CASA-CMTS(conf-dsg-tunnel-2)# no service-class private-class

CASA CMTS

CASA-CMTS(config)# dsg tunnel 2 CASA-CMTS(conf-dsg-tunnel-2)# CASA-CMTS(conf-dsg-tunnel-id)# end CASA-CMTS(config)# CASA-CMTS(config)# no dsg tunnel 2

CASA CMTS

CASA-CMTS(conf-dsg-tunnel-2)# classifier 1 20 192.168.0.1/24 224.0.0.100 indcd 6666 6667 CASA-CMTS(conf-dsg-tunnel-2)# no classifier 1 20 192.168.0.1/24 224.0.0.100 indcd 6666 6667

CASA-CMTS(config)# show dsg tunnel 2 client-list 123 service-class private-class classifier 1 20 192.168.0.1/24 224.0.0.100 indcd

CASA-CMTS# show cable dsg tunnel 1 cfrs cfr cfr cfr destination ip source ip srcPre d_port d_port id state pri address address length start end

CASA CMTS

CASA-CMTS(config)# no dsg tunnel-group 2

CASA-CMTS(conf-dsg-tunnel-grp-2)# channel 1 qam x/y/z rule-priority 20 vendor-param-id 1 ucidlist 1 CASA-CMTS(conf-dsg-tunnel-grp-2)# no channel 1

CASA CMTS

CASA-CMTS(config)#show dsg downstream dcd ds dcd dcd num of dcd num of dcd num of i/f state Tx sent change cnt fragment 0/1/0 dis off 0 0 0/1/1 dis off 0 0 0/1/2 dis off 0 0 0/1/3 dis off 0 0

0 0 0 0

CASA-CMTS(config)#show dsg downstream 1 tunnel 1

CASA-CMTS(config)# interface qam 0/1

CASA CMTS

CASA-CMTS(conf-qam 0/1)# channel 0 dsg timer-id 1

CASA-CMTS(config)# interface qam 0/1

CASA-CMTS(conf-qam 0/1)# channel 0 dsg vendorparam-id 2

CASA-CMTS(config)# interface qam 0/1

CASA CMTS

CASA-CMTS(conf-qam 0/1)# channel 0 dsg channellist 3 CASA-CMTS(conf-qam-id)# no channel 0 dsg channellist 3

CASA-CMTS(config)# interface qam 0/1

CASA-CMTS(conf-qam 0/1)# channel 0 dsg dcd-enable CASA-CMTS(conf-qam-id)# no channel 0 dsg dcdenable

CASA-CMTS(config)# interface qam 0/1

CASA CMTS

CASA-CMTS(conf-qam 0/1)# channel 0 dsg interval 5 CASA-CMTS(conf-qam 0/1)# no channel 0 dsg interval 5

CASA-CMTS(config)#show interface qam 2/0 interface qam 2/0 no spectral inversion on annex B modulation 256qam interleave 128x1 power 510 channel 0 frequency 549000000 channel 0 dsg channel-list 3 channel 0 dsg timer-id 1 channel 0 dsg vendor-param-id 2 channel 0 dsg interval 5 channel 0 dsg dcd-enable no channel 0 shutdown channel 1 frequency 555000000 no channel 1 shutdown channel 2 frequency 561000000 no channel 2 shutdown channel 3 frequency 567000000 no channel 3 shutdown no shutdown!

CASA CMTS

CASA-CMTS(config)# dsg client-list 1 client 1 idtype broadcast id-value 2048 vendor-param-id 2 CASA-CMTS(config)# no dsg client-list 1 client 1

CASA-CMTS(config)# show dsg client-list 1

CASA CMTS

dsg client-list 1 client 1 id-type broadcast idvalue 2048 vendor-param-id 2

CASA-CMTS(config)# dsg vendor-param-id 1 vendor 1 oui 01:02:03 value abc CASA-CMTS(config)# no dsg vendor-param-id 1 vendor 1

CASA-CMTS(config)# show dsg vendor-param- 1 dsg vendor-param-id 1 vendor 1 oui 01:02:03 value abc

CASA CMTS

CASA-CMTS(config)# dsg channel-list 1 channel 1 frequency 526000000 CASA-CMTS(config)# no dsg channel-list 1 channel 1

CASA-CMTS(config)# show dsg channel-list 1 dsg channel-list 1 channel 1 frequency 526000000

CASA CMTS

CASA-CMTS(config)# dsg timer-id 1 t1 20 t2 30 t3 40 t4 50 CASA-CMTS(config)# no dsg timer-id 1

CASA-CMTS(config)#show dsg timer 1 dsg timer-id 1 t1 20 t2 30 t3 40 t4 50

CASA-CMTS(config)# dsg unicast-port 1

CASA CMTS

CASA-CMTS(config)# show dsg statistics dcd

CASA-CMTS(config)# show dsg running-config dsg tunnel-group 1 channel 2 qam 0/1/0 rule-priority 1 dsg tunnel 1 group 1 dst-address 0010.5e00.1123 classifier 20 20 10.100.1.10/24 224.0.0.4 dsg client-list 1 client 1 id-type broadcast id-value 1 vendor-param-id 1 dsg vendor-param-id 1 vendor 1 oui 00:11:22 value 1 dsg channel-list 1 channel 1 frequency 640000 dsg timer-id 1 t1 1 t2 2 t3 3 t4 4 dsg server-redundancy enable dsg unicast port : 8888

CASA CMTS

CASA-CMTS(config)#igmp client version 3 CASA-CMTS(config)#interface gige 0 CASA-CMTS(conf-if-gige0)#ip igmp CASA-CMTS(config)#interface docsis-mac 3 CASA-CMTS(conf-if-mac3)# mgmd ipv4 version 3 CASA-CMTS(conf-if-mac3)# no mgmd ipv4 shutdown CASA-CMTS(config)# multicast default grpservice-class-name xyz CASA-CMTS(conf-service-class1)# name

CASA-CMTS(config)# dsg tunnel-group CASA-CMTS(conf-dsg-tunnel-grp1)# dsg channel qam rule-priority [vendor-param-id ] [ucid-list ] dsg tunnel-group channel 1 20 channel 2 20 channel 3 11 channel 4 11

1 qam 0/0/0

rule-priority

qam 0/0/1

rule-priority

qam 0/0/2

rule-priority

qam 0/0/3

rule-priority

CASA-CMTS(config)# dsg tunnel

CASA CMTS

>

CASA-CMTS(config)#cable sec sav-cfg-list host1 1 192.168.9.0/24

Spectrum management

CASA CMTS



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA CMTS



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA-CMTS(config-spec-rule 2)# end CASA-CMTS(config)#



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA CMTS

freq1 freq2

CASA-CMTS(conf-spec-rule 2)# frequency band 14000000 20000000 CASA-CMTS(conf-spec-rule 2)# frequency band 30000000 60000000 Remove frequency band 30-33 MHz from a spectrum group:

defined

CASA-CMTS(conf-spec-rule 2)# frequency band 14000000 20000000 CASA-CMTS(conf-spec-rule 2)# frequency band 30000000 60000000 CASA-CMTS(conf-spec-rule 2)# no frequency band 30000000 33000000 CASA-CMTS(conf-spec-rule 2)# show running-config … spectrum rule 2 frequency band 14000000 20000000 frequency band 33000000 60000000 …



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

freq

CASA-CMTS(conf-spec-rule 2)# frequency 34000000

CASA CMTS





CASA-CMTS(config)# hop period 100



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA-CMTS(conf-spec-rule 2)# action modulation frequency channel-width

CASA CMTS



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA-CMTS(conf-spec-rule 2)# channel-width 3200000 1600000



CASA CMTS

CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA-CMTS(conf-spec-rule 2)# profile 3 snr-threshold 130 CASA-CMTS(conf-spec-rule 2)# profile 4 snr-threshold 200 CASA-CMTS(conf-spec-rule 2)# no profile 3

CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA CMTS

CASA-CMTS(conf-spec-rule 2)# profile 3 snr-threshold 0



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)# profile 1 snr-threshold 100

CASA CMTS

CASA-CMTS#show spectrum snr-threshold-default Default SNR threshold per modulation type (tenth dB): Modulation Conservative Addressive QPSK: 130 100 8QAM: 190 160 16QAM: 220 190 32QAM: 250 220 64QAM: 280 250 128QAM: 310 290



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA-CMTS(conf-spec-rule 2)# correctable-fec threshold 5

CASA CMTS



CASA-CMTS(config)# spectrum rule 2 CASA-CMTS(conf-spec-rule 2)#

CASA-CMTS(conf-spec-rule 2)# uncorrectable-fec threshold 0

CASA-CMTS(config)# interface upstream 11/0 CASA-CMTS(config-if-ups 11/0.0)#

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)#spectrum-rule 10

CASA-CMTS(config)# interface upstream 11/0

CASA CMTS

CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 11/0.0)# logical-channel 0 profile 2 CASA-CMTS(config-if-ups 11/0.0)#

CASA-CMTS(config-if-ups 1/2)# logical-channel 0 profile 3 secondaryprofile 12,20,33

CASA CMTS

Set monitoring polling-period to 100 seconds: CASA-CMTS(config)# cable monitor-period 100

CASA-CMTS# show spectrum hop-history upstream 1/4 Port Action Time Code From To Reason 1/4/0 Mon Oct 26 22:12:26 2009 C 800000 1600000 SNR 283 (220) 1/4/0 Mon Oct 26 22:11:26 2009 C 1600000 800000 SNR 243 (220) cFEC 0 (3) uFEC 3 (1) 1/4/0 Mon Oct 26 21:34:26 2009 C 3200000 1600000 SNR 210 (220) cFEC 90 (3) uFEC 0 (1) 1/4/0 Mon Oct 26 21:33:56 2009 C 800000 3200000 SNR 281 (220) 1/4/0 Mon Oct 26 21:32:56 2009 M 12 22 SNR 285 (220) cFEC 0 (3) uFEC 20 (1) 1/4/0 Mon Oct 26 21:32:26 2009 C 1600000 800000 SNR 252 (250) cFEC 6 (3) uFEC 6 (1) 1/4/0 Mon Oct 26 21:31:56 2009 C 800000 1600000 SNR 288 (250) 1/4/0 Mon Oct 26 21:31:26 2009 C 1600000 800000 SNR 254 (250) cFEC 5 (3) uFEC 0 (1) 1/4/0 Mon Oct 26 21:30:56 2009 C 3200000 1600000 SNR 218 (250) cFEC 113 (3) uFEC 0 (1) 1/4/0 Mon Oct 26 21:30:26 2009 C 800000 3200000 SNR 285 (250) 1/4/0 Mon Oct 26 21:29:56 2009 C 1600000 800000 SNR 247 (250) cFEC 38 (3) uFEC 0 (1)

CASA CMTS

1/4/0 1600000 1/4/0 800000 1/4/0 1600000 1/4/0 800000 1/4/0 1600000 1/4/0 6400000 1/4/0 12 1/4/0 10 1/4/0 800000 1/4/0 3 1/4/0 6400000 1/4/0 17000000

Mon Oct 26 21:29:26 2009 C 800000 SNR 282 (250) Mon Oct 26 21:28:26 2009 C 1600000 SNR 258 (250) cFEC 4 (3) uFEC 0 (1) Mon Oct 26 21:27:56 2009 C 800000 SNR 281 (250) Mon Oct 26 21:26:56 2009 C 1600000 SNR 253 (250) cFEC 13 (3) uFEC 0 (1) Mon Oct 26 21:26:26 2009 C 6400000 SNR 192 (250) cFEC 100 (3) uFEC 19 (1) Mon Oct 26 21:25:56 2009 C 800000 SNR 288 (250) Mon Oct 26 21:20:26 2009 M 10 SNR 283 (250) cFEC 0 (3) uFEC 25 (1) Mon Oct 26 21:19:56 2009 M 3 SNR 286 (290) cFEC 0 (3) uFEC 3 (1) Mon Oct 26 21:18:26 2009 C 6400000 SNR 211 (280) cFEC 202 (3) uFEC 0 (1) Mon Oct 26 21:17:25 2009 M 0 Configuration change Mon Oct 26 21:17:25 2009 C 0 Configuration change Mon Oct 26 21:17:25 2009 F 0 Configuration change

CASA-CMTS(config)# show spectrum-map upstream 1/2 Spectrum Map for interface 1 /2.0 band 0: [18000000, 20000000] ...narrower than current chan-width 3200000 band 1: [22000000, 25400000] band 2: [28600000, 40000000] band 3: [58400000, 61600000]

CASA CMTS

chan_width

CASA-CMTS(config)# show spectrum upstream 2/0 raw FREQUENCY NOISE-LEVEL at channel-width 3200000 (dBmV) 5000000: -42.1 8200000: -42.1 11400000: -42.1 14600000: -42.1 17800000: -42.1 21000000: -42.1 24200000: -42.1 27400000: -42.1 30600000: -42.1 33800000: -42.1 37000000: -42.1 40200000: -35.1 43400000: -42.1 46600000: -42.1 49800000: -42.1 53000000: -42.1 56200000: -42.1 59400000: -42.1 62600000: -42.1 CASA-CMTS(config)# width 6400000 raw FREQUENCY

show spectrum upstream 2/0 chan-

NOISE-LEVEL (dB) 5000000: 9.5 11400000: 0.0 17800000: 7.8 24200000: 7.8 30600000: 6.0 37000000: 7.0 43400000: 17.2 49800000: 9.5 56200000: 9.5 62600000: 6.0

at channel-width 6400000

CASA CMTS

CASA-CMTS(config)# spectrum rule 1 CASA-CMTS(conf-rule 1)#

CASA-CMTS(conf-rule CASA-CMTS(conf-rule 3 CASA-CMTS(conf-rule CASA-CMTS(conf-rule

1)# correctablefec threshold 5 1)# uncorrectablefec threshold 1)# cm-hop 1)# interface ups 1/0

CASA-CMTS(conf-rule 1)# no cm-hop

CASA-CMTS(config)# spectrum rule 1 CASA-CMTS(conf-rule 1)#

CASA-CMTS(config)# spectrum rule 1 CASA-CMTS(conf-rule 1)# show cm-hop log

CASA CMTS

CASA CMTS

CASA-CMTS(config)#show spectrum-map upstream 8/1 Spectrum Map for interface 8/1/0 band 0: [28000000, 32800000] band 1: [36000000, 38400000] band 2: [41600000, 42000000]

spectrum rule 2 frequency band 26000000 42000000 action frequency

CASA-CMTS(config-if-ups 8/1)#show spectrum-map upstream 8/1 Spectrum Map for interface 8/1/0 band 0: [26000000, 32800000] band 1: [36000000, 38400000] band 2: [41600000, 42000000]

[Wed Dec 2 21:26:18 2009]-DE-CSM-FSM-1: 30000000 to 27600000 CASA-CMTS#show spectrum hop-history Port Action Time 8/1/0 Wed Dec 2 21:26:18 2009 cFEC 2 (3) uFEC 30 (1) 8/1/0 Wed Dec 2 21:20:29 2009 change 8/1/0 Wed Dec 2 20:58:46 2009 cFEC 0 (3) uFEC 29 (1) 8/1/0 Wed Dec 2 20:54:16 2009 change 8/1/0 Wed Dec 2 20:31:14 2009 cFEC 1 (3) uFEC 29 (1) 8/1/0 Wed Dec 2 20:29:33 2009 Configuration 8/1/0 Wed Dec 2 17:08:59 2009 cFEC 1 (3) uFEC 28 (1) 8/1/0 Wed Dec 2 16:41:45 2009 change 8/1/0 Wed Dec 2 16:41:45 2009

H -> R on 8/1/0.. freq hop

upstream 8/1 Code From F 30000000

To 27600000

Reason SNR 80 (280)

F

0

30000000

Configuration

F

30000000

29600000

SNR 131 (280)

F

0

30000000

Configuration

F

30000000

29600000

SNR 100 (280)

F

29600000

30000000

Back to

F

30000000

29600000

SNR 106 (280)

M

0

10

Configuration

C

0

3200000

Configuration

CASA CMTS

change 8/1/0 change

Wed Dec

2 16:41:45 2009

F

0

30000000

Configuration

spectrum rule 1 channel-width 6400000 800000 action modulation channel-width correctable-fec threshold 3 uncorrectable-fec threshold 1 profile 3 snr-threshold 280 profile 12 snr-threshold 250 profile 22 snr-threshold 220 profile 30 snr-threshold 190 profile 33 snr-threshold 150 interface upstream 1/0 spectrum-rule 1 … logical-channel 0 profile 3 secondary-profile 12,22,30,33

spectrum rule 20 frequency 60000000 frequency band 5500000 40000000 frequency band 46000000 51200000 channel-width 6400000 800000 action frequency channel-width modulation correctable-fec threshold 3 uncorrectable-fec threshold 0 profile 10 snr-threshold 300 profile 20 snr-threshold 260 interface upstream 2/0.0 spectrum-rule 20 …. logical-channel 0 profile 10 secondary-profile 20

Spectrum measurement (DOCSIS 3.0 only)

CASA CMTS



CASA-CMTS(config)# show spectrum-meas upstream 2/0

Displaying spectrum measurement results for upstream interface 2/0 CASA-CMTS(config)# show spectrum-meas upstream 2/0 2/0 (0) Spectrum MEAS data (in Hz): chan cnter freq: 8000000 frequency span: 10240000 number of bins: 513 resolution bw: 20000 bin spacing: 20000 F4 F4 F2 F2 F4 F4 F2 F2 F4 F2 F2 F4 F4 F2

F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2

F4 F4 F2 F2 F4 F4 F2 F4 F4 F2 F2

F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2

F2

F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4

F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4

CASA CMTS

F4 F2 F2 F4 F4 F2

F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4

F4 F4 F2 F2 F4 F7 4C F4 F4 F2 F2 F4 F4 F2 F2 F4 F4 F2 F4 F4 F2 F2 F4

F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2

F2

F4

F2 F2 F4 F4 F2 F2 F4 F2 F2 F4 F4 F2 F4 F4 F2 F2 F4 F4

F2

F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4

F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F7 4C F8 DA F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2 F4 F2

CASA CMTS

CASA-CMTS(config)# show spectrum-meas upstream 2/0

Spectrum analysis across the entire spectrum CASA-CMTS(config)# spectrum analysis full-spectrum CASA-CMTS# show spectrum-meas upstream 1/0 1/0 (0) Spectrum MEAS data (in Hz): chan cnter freq: 40960000 frequency span: 81920000 number of bins: 1024 resolution bw: 80000 bin spacing: 80000 FC 66 FE C0 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6 52 F6  52  F6  52  F6  52  F6  52  F6  52  F6  52  F6  52  F6  52  F6  ……………….

Configuring load balancing

CASA CMTS

CASA CMTS

CASA CMTS

CASA-CMTS(config)# load-balance enable CASA-CMTS(config)# no load-balance enable

Disabling upstream load balancing

CASA CMTS

CASA-CMTS(config)# load-balance enable across-mac CASA-CMTS(config)# no load-balance enable across-mac

Entering the general load balance group default

CASA-CMTS(config)# load-balance general-group default-settings CASA-CMTS(load-bal-general-default)#

CASA CMTS

Entering the general load balance group

CASA-CMTS(config)# load-balance general-group macdomain 1 service-group FN_A CASA-CMTS(load-bal-general-mac-1-sg-FN_A)#

Enabling the load balance function on a MAC-SG general group

CASA-CMTS(config)# load-balance general-group default-settings CASA-CMTS(load-bal-general-default)#

CASA-CMTS(load-bal-general-default)# enable CASA-CMTS(load-bal-general-default)# no enable

Specifying the technique for moving cable modems

CASA CMTS

CASA-CMTS(config)# load-balance general-group default-settings CASA-CMTS(load-bal-general-default)#

CASA-CMTS(load-bal-general-default)#initial-tech broadcast-ranging

Specifying the policy for load balancing execution

CASA-CMTS(config)# load-balance general-group default-settings CASA-CMTS(load-bal-general-default)#

CASA CMTS

CASA-CMTS(load-bal-general-default)# policy-id 2

Entering a basic rule configuration

CASA-CMTS(config)# load-balance basic-rule 1

Enabling a basic rule

CASA-CMTS(config)# load-balance basic-rule 1

CASA-CMTS(load-balance basic-rule 1)# enable CASA-CMTS(load-balance basic-rule 1)# no enable

Specifying a time period on a basic rule to disable a load balance function

CASA CMTS

CASA-CMTS(config)# load-balance execution-rule 1 CASA-CMTS(load-bal-exe-rule 1)#

CASA-CMTS(load-bal-exe-rule 1)#suspend-load-balance from 12:00:00 to 15:00:00

CASA-CMTS(config)# load-balance execution-rule 1

CASA CMTS

Specifying a minimum time Interval between each load balance calculation

CASA-CMTS(config)# load-balance execution-rule 1 CASA-CMTS(load-bal-exe-rule 1)#

CASA-CMTS(load-bal-exe-rule 1)# interval 200

Specifying a minimum time interval between upstream load balance calculations

CASA-CMTS(config)# load-balance execution-rule 1 CASA-CMTS(load-bal-exe-rule 1)#

CASA CMTS

CASA-CMTS(load-bal-exe-rule 1)# upstream-interval 30

Specifying the minimum time interval to move the same modem

CASA-CMTS(config)# load-balance execution-rule 1 CASA-CMTS(load-bal-exe-rule 1)#

CASA-CMTS(load-bal-exe-rule 1)# cable modem rebalance-interval 200

CASA-CMTS(config)# load-balance execution-rule 1 CASA-CMTS(load-bal-exe-rule 1)#

CASA CMTS

CASA-CMTS(load-bal-exe-rule 1)# cable modem retryinterval first 35000 second 87000

Specifying a method for load balance calculations

CASA-CMTS(config)# load-balance execution-rule 5 CASA-CMTS(load-bal-exe-rule 5)#

CASA-CMTS(load-bal-exe-rul 5)#method utilization

CASA CMTS

CASA-CMTS(config)# load-balance execution-rule 5 CASA-CMTS(load-bal-exe-rule 5)#

CASA-CMTS(load-bal-exe-rul 5)#method modem

Specifying a method for upstream load balance calculations

CASA-CMTS(config)# load-balance execution-rule 5 CASA-CMTS(load-bal-exe-rule 5)#

CASA-CMTS(load-bal-exe-rul 5)# upstream-method utilization

CASA-CMTS(config)# load-balance execution-rule 5 CASA-CMTS(load-bal-exe-rule 5)#

CASA CMTS

CASA-CMTS(load-bal-exe-rul 5)#method modem

Specifying a utilization method for upstream load balance calculations

CASA-CMTS(config)# load-balance execution-rule 5 CASA-CMTS(load-bal-exe-rule 5)#

CASA CMTS

CASA-CMTS(config)# load-balance execution-rule 5 CASA-CMTS(load-bal-exe-rule 5)# upstreamthreshold load350 enforce 50 minimum 50 dynamic minimum 50

CASA-CMTS(config)# load-balance policy 5 CASA-CMTS(load-bal-policy 5)#

Adding a basic rule

CASA-CMTS(config)# load-balance policy 5 CASA-CMTS(load-bal-policy 5)#

CASA CMTS

CASA-CMTS(load-bal-policy 5)# rule basic 10

Adding an execution rule

CASA-CMTS(config)# load-balance policy 5 CASA-CMTS(load-bal-policy 5)#

CASA-CMTS(load-bal-policy 5)# rule execution 10

Entering the load balance restricted group

CASA CMTS

CASA-CMTS(config)# load-balance restricted-group 2 CASA-CMTS(load-bal-restrict 2)#

Specifying the MAC domain on a restricted group

CASA-CMTS(config)# load-balance restricted-group 2 CASA-CMTS(load-bal-restrict-group-2)#

CASA-CMTS(load-bal-restrict-2)# docsis-mac 1

Enabling load balancing on a restricted group

CASA-CMTS(config)# load-balance restricted-group 2 CASA-CMTS(load-bal-restrict 2)#

CASA CMTS

CASA-CMTS(load-bal-restrict 2)# docsis-mac 1 CASA-CMTS(load-bal-restrict 2)#

CASA-CMTS(load-bal-restrict 2)# enable

Adding the service type ID to a restricted group

CASA-CMTS#config CASA-CMTS(config)#

CASA-CMTS(config)# load-balance restricted-group 2 CASA-CMTS(load-bal-restrict 2)#

CASA-CMTS(load-bal-restrict 2)# docsis-mac 1 CASA-CMTS(load-bal-restrict 2)#

CASA CMTS

CASA-CMTS(load-bal-restrict 2)# service-type-id “load  balance” CASA-CMTS(load-bal-restrict 2)#

Displaying cable modem information by service-type-id

CASA-CMTS(config)#show cable modem service-type-id

C10G-RC220#show cable modem service-type-id MAC Address Type_ID(C/P)

IP Address

US

DS

MAC

Prim Service-

0005.caa3.d5c4 0017.9a60.5c30 0025.2e06.70ec 0026.2495.b89c 0026.5e77.43b3 C10G-RC220#

10.220.1.137 10.220.1.146 10.220.1.129 0.0.0.0 10.220.1.123

Intf 11/0.0/0 11/0.0/0 11/0.0/0 11/7.0/0 11/0.0/0

Intf 2/0/7 2/0/6 2/0/4* 1/7/7 2/0/7*

Status init(o) online(pt) online(pt) offline online(pt)

Sid 19 3 4 0 1

Adding an upstream channel to a restricted group

-/-/-/-/-/-

CASA CMTS

CASA-CMTS(config)# load-balance restricted-group 2 CASA-CMTS(load-bal-restrict 2)#

CASA-CMTS(load-bal-restrict 2)# docsis-mac 1 CASA-CMTS(load-bal-restrict 2)#

CASA-CMTS(load-bal-restrict 2)# upstream 5/0.0/1 CASA-CMTS(load-bal-restrict 2)#

Adding a downstream channel to a restricted group

CASA CMTS

CASA-CMTS(config)# load-balance restricted-group group-id 2 CASA-CMTS(load-bal-restrict-group-2)#

CASA-CMTS(load-bal-restrict-group-2)# docsis-mac 1 CASA-CMTS(load-bal-restrict-mac-id-group-1)#

CASA-CMTS(load-bal-restrict 2)# qam 1/1/0 CASA-CMTS(load-bal-restrict 2)#

Adding a CM to an exclusion list

CASA CMTS

CASA-CMTS(config)# load-balance exclusion list CASA-CMTS(load-bal-exclusion-list)#

CASA-CMTS(config)# load-balance exclusion list CASA-CMTS(load-bal-exclusion-list)# mac addr 0014.0000.0000 mask ffff.0000.0000

Entering the restricted CM configuration

CASA CMTS

CASA-CMTS(config)# load-balance restricted-cm 1 CASA-CMTS(load-bal-restrict-cm 1)#

Entering the CM MAC address

CASA-CMTS(config)# load-balance restricted-cm 1 CASA-CMTS(load-bal-restrict-cm 1)# mask

CASA-CMTS(load-bal-restrict-cm 1)mac addr 0011.e6bb.e3b1 #

Adding a service type ID

CASA CMTS

CASA-CMTS(config)# load-balance restricted-cm 1 CASA-CMTS(load-bal-restrict-cm 1)#

CASA-CMTS(load-bal-restrict-cm 1)# service-typeid  “load  balance” CASA-CMTS(load-bal-restrict-cm 1)#

Adding a reference to a restricted load balance group

CASA-CMTS(config)# load-balance restricted-cm 1 CASA-CMTS(load-bal-restrict-cm 1)# id

CASA-CMTS(load-bal-restrict-cm 1)# load-balance-group 3

restricted-

CASA-CMTS(load-bal-restrict-cm 1)# restricted-load-balance-group

no

CASA CMTS

Changing upstream and downstream channels with the DCC method

CASA-CMTS(config)# cable modem 0015.f2fe.c904 dcc change-frequency 593000000 upstream 200 initialtech reinitialize-mac

CASA CMTS

Changing a downstream channel with the DCC method

CASA-CMTS(config)# cable modem 0015.f2fe.c904 dcc change-frequency 593000000 initial-tech periodranging

CASA CMTS

Changing an upstream channel with the DCC method

CASA-CMTS(config)# cable modem 0015.f2fe.c904 dcc upstream 200 initial-tech broadcast-ranging

CASA CMTS

Changing the CM to another CMTS with the DCC method

CASA-CMTS(config)# cable modem 0015.f2fe.c904 dcc change-frequency 593 initial-tech reinitializemac

Setting the upstream channel frequency difference limit on the DCC when the initial technique is direct

CASA-CMTS(config)# load-balance general-group default-settings CASA-CMTS(load-bal-general-default)#

CASA CMTS

CASA-CMTS(load-bal-general-default)# initial-tech direct frequency-limit 40

Changing an upstream channel with the UCC method

CASA-CMTS(load-bal-general-default)# cable modem 0001.0002.0003 ucc upstream 100

Changing  a  bonded  CM’s  upstream  and  downstream  with  the  DBC  method

CASA CMTS

C3000-230(config)#cable modem 0001.0002.0003 dbc rcp-id 01:FE:EA:00:04 rcc-id 200 upstream-list 1 initial-tech period-ranging

Changing  a  bonded  CM’s  downstream  channel  with  the  DBC  method

CASA CMTS

C3000-230(config)#cable modem 0001.0002.0003 dbc downstream-list 1 initial-tech period-ranging

Changing a bonded CM’s  upstream channel via the DBC method

C3000-230(config)#cable modem 0001.0002.0003 dbc upstream-list 1 initial-tech period-ranging

Sending DBC request messages to cable modems

CASA CMTS

CASA(config)#cable partial-service dbc

Configuring CableLabs Engineering Change Notice 770

CASA(config)#cable ecn 770

CASA CMTS

CASA-CMTS# show load-balance dynamic

show load-balance dynamic Mac address Mac-id upstream-channel downstream-channel initial_tech cmd status type time 0015.f2fe.c643 0 3 -1 dcc WaitToSendMsg GLB 2008-04-06 23:25:17 0015.f2fe.c643 0 2 -1 dcc WaitToSendMsg RGLB 2008-04-06 23:28:41 ----------------------------------------------------------------------total: 2; success:0; other:2

CASA CMTS

Clearing all load-balance logs

CASA-CMTS# clear load-balance log

CASA CMTS

Default values for general load-balance group default enable initial-tech-none no policy-id

Default values for general/restricted load-balance group

Default values for load-balance basic rule no enable

Default values for load-balance execution rule interval 10 method modem threshold load 10 enforce 0 minimum 10

CASA-CMTS# show run ! ! CASA-CMTS system running configuration ! hostname "sada" ! password casa ! ! interface eth 0 ip address 192.168.2.240 255.255.255.0 ! interface ip-bundle 1 ip address 10.248.1.1 255.255.255.0 cable helper-address 192.168.3.8 ! ! interface gige 0 ip address 192.168.3.48 255.255.255.0 ipv6 address 2001:50:1::3/64 no shutdown ! interface gige 1 shutdown ! interface gige 2

CASA CMTS

shutdown ! interface gige 3 shutdown ! ! cable sec tftp-options none no cable sec config-file-learning cable sec cert-revocation-list url cable sec ocsp protocol-url ! ! interface qam 0/0 interleave 128x1 power 540 channel 0 frequency 669000000 no channel 0 shutdown channel 1 frequency 675000000 no channel 1 shutdown channel 2 frequency 681000000 no channel 2 shutdown channel 3 frequency 687000000 no channel 3 shutdown no shutdown interface qam 0/1 interleave 128x1 power 540 channel 0 frequency 549000000 no channel 0 shutdown channel 1 frequency 555000000 no channel 1 shutdown channel 2 frequency 561000000 no channel 2 shutdown channel 3 frequency 567000000 no channel 3 shutdown no shutdown interface qam 0/2 interleave 128x1 channel 0 frequency channel 0 shutdown channel 1 frequency channel 1 shutdown channel 2 frequency channel 2 shutdown channel 3 frequency channel 3 shutdown shutdown

549000000 555000000 561000000 567000000

interface qam 0/3 interleave 128x1 power 450 channel 0 frequency 549000000 no channel 0 shutdown channel 1 frequency 555000000 no channel 1 shutdown

CASA CMTS

channel 2 frequency 561000000 no channel 2 shutdown channel 3 frequency 567000000 no channel 3 shutdown shutdown ! igmp client version 2 ! service group FN_A qam 0/0/0 qam 0/0/1 qam 0/0/2 qam 0/0/3 upstream 1/0 upstream 1/1 service group FN_B qam 0/1/0 qam 0/1/1 qam 0/1/2 qam 0/1/3 upstream 1/2 upstream 1/3 upstream map size 5 interface docsis-mac 1 no shutdown no dhcp-authorization no early-authentication-encryption no multicast-dsid-forward no tftp-proxy ip bundle 1 downstream 1 interface qam 0/0/0 downstream 2 interface qam 0/0/1 downstream 3 interface qam 0/0/2 downstream 4 interface qam 0/0/3 downstream 5 interface qam 0/1/0 downstream 6 interface qam 0/1/1 downstream 7 interface qam 0/1/2 downstream 8 interface qam 0/1/3 upstream 1 interface upstream 1/0/0 upstream 2 interface upstream 1/1/0 upstream 3 interface upstream 1/2/0 upstream 4 interface upstream 1/3/0 ! ! channel-utilization-interval 0 interface upstream 1/0 frequency 8000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 logical-channel 0 pre-equalization

CASA CMTS

no logical-channel 0 shutdown logical-channel 1 profile 5 logical-channel 1 frame 16 8 128 no logical-channel 1 shutdown no shutdown interface upstream 1/1 frequency 12000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 5 logical-channel 1 frame 16 8 128 no logical-channel 1 shutdown no shutdown interface upstream 1/2 frequency 16000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 5 logical-channel 1 frame 16 8 128 no logical-channel 1 shutdown no shutdown interface upstream 1/3 frequency 20000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 5 logical-channel 1 frame 16 8 128 no logical-channel 1 shutdown no shutdown interface upstream 1/4 frequency 24000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown no shutdown interface upstream 1/5 frequency 28000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown

CASA CMTS

logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown no shutdown interface upstream 1/6 frequency 32000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown no shutdown interface upstream 1/7 frequency 36000000 channel-width 3200000 logical-channel 0 profile 2 logical-channel 0 minislot 2 no logical-channel 0 shutdown logical-channel 1 profile 2 logical-channel 1 minislot 2 logical-channel 1 shutdown no shutdown ! ! ! load balance commands ! load-balance enable load-balance basic-rule 1 enable suspend-load-balance from 13:00:00 to 20:00:00 load-balance basic-rule 2 enable suspend-load-balance from 13:00:00 to 23:00:00 load-balance basic-rule 3 enable suspend-load-balance from 20:00:00 to 01:00:00 load-balance execution-rule 1 enable method modem threshold load 10 enforce 30 minimum 35 load-balance policy 1 rule basic 1 rule basic 3 rule execution 1

CASA CMTS

load-balance general-group default-settings initial-tech unicast-ranging load-balance general-group mac-domain 1 service-group FN_A enable initial-tech direct policy-id 1 load-balance general-group mac-domain 1 service-group FN_B no enable initial-tech direct policy-id 1 load-balance restricted-group group-id 10 enable docsis-mac 1 initial-tech broadcast-ranging policy-id 1 service-type-id restict1 qam 0/1/0 qam 0/1/1 qam 0/1/2 upstream 1/2 upstream 1/3 load-balance restricted-cm 1 mac addr 0018.0123.5678 service-type-id restict1 restricted-load-balance-group 10 load-balance restricted-cm 2 mac addr 0019.0000.0000 mask ffff.0000.0000 service-type-id restict1 restricted-load-balance-group 10 bonding-group downstream mac-domain 1 group-id 1 prov-attr-mask 0x00ff reseq wait-time 1000 reseq warn-thrshld 1200 qam 0/0/0 qam 0/0/1 qam 0/0/2 qam 0/0/3 bonding-group upstream mac-domain 1 group-id 1 prov-attr-mask 0x00ff upstream 1/0/0 upstream 1/1/0 ! ! !

end of config

CASA CMTS

Configuring channel bonding operations

Where:

CASA-CMTS(config)# service group 1 CASA-CMTS(conf-svc-grp 1)# Where:

CASA-CMTS(conf-svc-grp 1)# qam 0/0/0 CASA-CMTS(conf-svc-grp 1)#no qam 0/0/0

CASA CMTS

Where:

CASA-CMTS(conf-svc-grp 1)# upstream ? X/Y.C X-slot number, Y-port number, Cphysical channel index 0 or 1 CASA-CMTS(conf-svc-grp 1)# upstream 3/0.1 CASA-CMTS(conf-svc-grp 1)# show service group CASA-CMTS(conf-svc-grp 1)# no upstream 3/0.1

Where:

CASA-CMTS(config)# interface docsis-mac 1 CASA-CMTS(conf-if-mac 1)#

Where:

CASA-CMTS(conf-if-mac 1)#downstream 1 interface qam 0/0/0

CASA CMTS

Where:

CASA-CMTS(conf-if-mac 1)# upstream 1 interface upstream ? X/Y.C/Z X - slot, Y - port (0-7), C upstream physical channel(0-1), Z - upstream logical channel(0-1 CASA-CMTS(conf-if-mac 1)# upstream 1 interface upstream 4/1.0/0 CASA-CMTS(conf-if-mac 1)# show interface docsismac 1 CASA-CMTS(conf-if-mac 1)#no upstream 1 CASA-CMTS(conf-if-mac 1)#

CASA-CMTS(config)# service group 1 CASA-CMTS(config-svc-grp 1)# qam 0/0/0 CASA-CMTS(config-svc-grp 1)# qam 0/0/1 CASA-CMTS(config-svc-grp 1)# qam 0/0/2 CASA-CMTS(config-svc-grp 1)# qam 0/0/3 CASA-CMTS(config-svc-grp 1)# qam 0/1/0 CASA-CMTS(config-svc-grp 1)# qam 0/1/1 CASA-CMTS(config-svc-grp 1)# qam 0/1/2 CASA-CMTS(config-svc-grp 1)# qam 0/1/3 CASA-CMTS(config-svc-grp 1)# qam 0/2/0 CASA-CMTS(config-svc-grp 1)# qam 0/2/1 CASA-CMTS(config-svc-grp 1)# qam 0/2/2 CASA-CMTS(config-svc-grp 1)# qam 0/2/3 CASA-CMTS(config-svc-grp 1)# qam 0/3/0 CASA-CMTS(config-svc-grp 1)# qam 0/3/1 CASA-CMTS(config-svc-grp 1)# qam 0/3/2 CASA-CMTS(config-svc-grp 1)# qam 0/3/3 CASA-CMTS(config-svc-grp 1)# upstream 1/0 CASA-CMTS(config-svc-grp 1)# upstream 1/1

CASA CMTS

CASA-CMTS(config-svc-grp 1)# upstream 1/2 CASA-CMTS(config-svc-grp 1)# upstream 1/3 CASA-CMTS(config-svc-grp 1)# upstream 1/4 CASA-CMTS(config-svc-grp 1)# upstream 1/5 CASA-CMTS(config-svc-grp 1)# upstream 1/6 CASA-CMTS(config-svc-grp 1)# upstream 1/7 CASA-CMTS(config-svc-grp 1)# end CASA-CMTS(config)# interface docsis-mac 1 CASA-CMTS(config-if-mac 1)# no shutdown CASA-CMTS(config-if-mac 1)# no dhcp-authorization CASA-CMTS(config-if-mac 1)# no early-authentication-encryption CASA-CMTS(config-if-mac 1)# no tftp-proxy CASA-CMTS(config-if-mac 1)# ip address 10.15.131.1 255.255.255.0 CASA-CMTS(config-if-mac 1)# cable helper-address 192.168.3.6 CASA-CMTS(config-if-mac 1)# downstream 1 interface qam 0/0/0 CASA-CMTS(config-if-mac 1)# downstream 2 interface qam 0/0/1 CASA-CMTS(config-if-mac 1)# downstream 3 interface qam 0/0/2 CASA-CMTS(config-if-mac 1)# downstream 4 interface qam 0/0/3 CASA-CMTS(config-if-mac 1)# downstream 5 interface qam 0/1/0 CASA-CMTS(config-if-mac 1)# downstream 6 interface qam 0/1/1 CASA-CMTS(config-if-mac 1)# downstream 7 interface qam 0/1/2 CASA-CMTS(config-if-mac 1)# downstream 8 interface qam 0/1/3 CASA-CMTS(config-if-mac 1)# upstream 1 interface upstream 1/0/0 CASA-CMTS(config-if-mac 1)# upstream 2 interface upstream 1/1/0 CASA-CMTS(config-if-mac 1)# upstream 3 interface upstream 1/2/0 CASA-CMTS(config-if-mac 1)# upstream 4 interface upstream 1/3/0 CASA-CMTS(config-if-mac 1)# end CASA-CMTS(config)# interface docsis-mac 2 CASA-CMTS(config-if-mac 2)# no shutdown CASA-CMTS(config-if-mac 2)# no dhcp-authorization CASA-CMTS(config-if-mac 2)# no early-authentication-encryption CASA-CMTS(config-if-mac 2)# no tftp-proxy CASA-CMTS(config-if-mac 2)# ip address 10.15.131.2 255.255.255.0 CASA-CMTS(config-if-mac 2)# cable helper-address 192.168.3.6 CASA-CMTS(config-if-mac 2)# downstream 1 interface qam 0/2/0 CASA-CMTS(config-if-mac 2)# downstream 2 interface qam 0/2/1 CASA-CMTS(config-if-mac 2)# downstream 3 interface qam 0/2/2 CASA-CMTS(config-if-mac 2)# downstream 4 interface qam 0/2/3 CASA-CMTS(config-if-mac 2)# downstream 5 interface qam 0/3/0 CASA-CMTS(config-if-mac 2)# downstream 6 interface qam 0/3/1 CASA-CMTS(config-if-mac 2)# downstream 7 interface qam 0/3/2 CASA-CMTS(config-if-mac 2)# downstream 8 interface qam 0/3/3 CASA-CMTS(config-if-mac 2)# upstream 1 interface upstream 1/4/0 CASA-CMTS(config-if-mac 2)# upstream 2 interface upstream 1/5/0 CASA-CMTS(config-if-mac 2)# upstream 3 interface upstream 1/6/0 CASA-CMTS(config-if-mac 2)# upstream 4 interface upstream 1/7/0 CASA-CMTS(config-if-mac 2)# end CASA-CMTS(config)#

Creating static CM bonding groups

CASA CMTS

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group downstream macdomain 7 group-id 1 CASA-CMTS(bond-ds-mac-7-group-1)#

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group upstream macdomain 7 group-id 1 CASA-CMTS(bond-us-mac-7-group-1)#

CASA CMTS

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group upstream macdomain 7 group-id 1 CASA-CMTS(bond-us-mac-7-group-1)# mask Where:

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group downstream macdomain 7 group-id 1 CASA-CMTS(bond-ds-mac-7-group-1)# mask Where:

CASA CMTS

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group upstream macdomain 7 group-id 1 CASA-CMTS(bond-us-mac-7-group-1)# Where:

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group downstream macdomain 7 group-id 1 CASA-CMTS(bond-ds-mac-7-group-1)# x/y/z Where:

CASA CMTS

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group downstream macdomain 7 group-id 1 CASA-CMTS(bond-ds-mac-7-group-1)# value Where:

dmn_id grp_id Where:

CASA-CMTS(config)# bonding-group downstream macdomain 7 group-id 1 CASA-CMTS(bond-ds-mac-7-group-1)# Where:

CASA CMTS

QoS support

CASA CMTS

Configuring QoS

CASA CMTS

class-index Where: class-index

CASA-CMTS(config)# cable service-class 100

sclass-index Where:

CASA-CMTS# show cable service-class Index Name

Dir

Sched

Prio

CASA CMTS

MaxSusRate MaxBurst 1 UP_UGS 1522 0 2 UP_UGSAD 1522 0 3 UP_RTPS 2000 64000 4 UP_BE 2000 0 5 DOWN_BE 3000 0

MinRsvRate US/DS UGS

0

0

US/DS UGS_AD 0

0

US/DS RTPS

0

128000

US/DS BE

5

128000

US/DS BE

5

1000000

CASA-CMTS# show cable service-class 1 verbose Index: Name: Direction: Upstream/Downstream Traffic Priority: Maximum Sustained Rate: bits/sec Max Burst: bytes Minimum Reserved Rate: bits/sec Minimum Packet Size Admitted QoS Timeout seconds Active QoS Timeout seconds Scheduling Type: Unsolicited Grant Service Request/Transmission Policy: Unsolicited Grant Size: Nominal Grant Interval: usecs Tolerated Grant Jitter: usecs Grants per Interval: IP ToS Overwrite [AND-mask,OR-mask]: Max Latency: Parameter Presence Bitfield: 0xBCC000}

1 UP_UGS 0 0 1522 0 100 bytes 30 30

0x1FF 100 bytes 20000 4000 1 0xE0,0xA0 0 usecs {0xE08,

CASA CMTS

Where:

Where:

Where:

Where:

CASA CMTS

Where:

Where:

CASA-CMTS(config)# interface gige 5

Where:

CASA-CMTS(conf-if-gige 5)#service-policy policy1 CASA-CMTS(conf-if-gige 5)#

Where:

CASA-CMTS(config)# interface docsis-mac 1 CASA-CMTS(conf-if-mac 1)#

Where:

CASA-CMTS(conf-if-mac 1)# service-policy policy1 CASA-CMTS(conf-if-mac 1)#

CASA CMTS

Where:

Where:

CASA-CMTS(conf-if-vlan 1)#service-policy policy1 CASA-CMTS(conf-if-vlan 1)#

Configuring SNMP (Enhanced for Rel. 5.4 and later)

CASA CMTS

Where:

CASA-CMTS(config)# snmp engineid 112233445566778899001112 CASA-CMTS(config)# no snmp engineid

Where:

CASA-CMTS (config)# snmp trap version 2 CASA-CMTS (config)# no snmp trap version 2

CMTS#config)#show running-config | i syslog no snmp trap version 1

CASA CMTS

Where:

CASA-CMTS (config)# snmp traphost 192.168.6.10 community public version 1

Where:

CASA-CMTS (config)# snmp-server location bostonOffice CASA-CMTS (config)# snmp-server  contact  “Fred   Gamble at 978-123-4567”

CASA CMTS

Where:

CASA-CMTS (config)# snmp trap-source loopback 6

Where:

CASA-CMTS (config)# snmp inform version 2 CASA-CMTS (config)# CASA-CMTS (config)# no snmp inform version 2 CASA-CMTS (config)#

CMTS#config)#show running-config  |  i  “no snmp inform” no snmp inform version 2

CASA CMTS

Where:

CASA-CMTS(config)# snmp community local ro CASA-CMTS(config)# show snmp community Community name: local Community Index: local Community SecurityName: rotesting Community StorageType: 3 Community Status: active

CASA-CMTS(config)# no snmp comm-tbl public CASA-CMTS(config)# show snmp community

roup

context read

write

Where: group

notify

CASA CMTS

context

read write notify

Where: : :

CASA CMTS

Where: comm_index comm_name sec_name context_id context_name tag

comm_index Where: comm_index

Where: name tag

CASA CMTS

CASA-CMTS(config)#snmp notify InformV2cSNMPv2cNotifyTagList InformV2cSNMPv2cNotifyTagList inform n on-volatile CASA-CMTS(config) show snmp

name Where:

sec_name group_name Where:

sec_name group_name

CASA CMTS

CASA-CMTS(config)#snmp security snmpv1 rotesting rotesting non-volatile CASA-CMTS(config) show snmp

time_out_num

tgt_addr retry_num

tag_list

td_addr param mask_value

Where: tgt_addr

td_addr time_out_num retry_num tag_list param

mask_value

CASA-CMTS(config)# snmp tgt-addr anywhere snmpUDPDomain 192.168.8.232:162 500 1 anywhereTag none non-volatile 255.255.0.0:162 500 CASA-CMTS(config) show snmp

CASA CMTS

addr Where: addr

param sec_name Where: param

sec_name

CASA-CMTS(config)# snmp tgt-param InformV3SNMPv3Notify 3 snmpv2c noAuthNoPrivUser no-auth non-volatile CASA-CMTS(config) show snmp

CASA CMTS

param Where: param

view

subtree

mask

Where: view subtree mask

CASA-CMTS(config)# snmp tree-family docsisManagerView 1.3.6.1.4.1.9.9 252 exclude non-volatile CASA-CMTS(config) show snmp

CASA CMTS

view

subtree

Where: view subtree

engine_id auth_pswd target_string Where: engine_id user_name

auth_pswd

priv_pswd

user_name priv_pswd

CASA CMTS

target_string

CASA-CMTS(config)#snmp user AuthPrivMD5User user1 md5 1 zYtNm no-priv 1 - non-volatile anyWhereTag CASA-CMTS(config) show snmp

show cable flap-list

CASA> show cable flap-list ****.****.****

CASA> show cable flap-list ****.****.**** mask ****.****.****

CASA> show cable flap-list upstream x/y

CASA> show cable flap-list upstream x/y/z

CASA> show cable flap-list downstream x/y/z

CASA> show cable flap-list sort-time CASA> show cable flap-list downstream x/y/z sort-time

CASA> show cable flap-list sort-int

CASA CMTS

CASA> show cable flap-list downstream x/y/z sort-int

CASA> show cable flap-list sort-flap CASA> show cable flap-list downstream x/y/z sort-flap

CASA> show cable flap-list sort-mac CASA> show cable flap-list downstream x/y/z sort-mac

CASA> show cable flap-list ****.****.**** detail

Start Time Offline Time -2009-08-23,21:51:20 2009-08-24,16:39:28 2009-08-24,20:20:35 2009-08-25,15:28:56 2009-08-25,18:53:52

Hit

Miss(%)

CRC

P-Adj

ARP-TO

1938

768 (28.4%)

0

0

0

online

1291

342 (20.9%)

0

0

0

init(r2)

1210

175 (12.6%)

0

0

0

init(r2)

Where:

CASA-CMTS# show cable modem summary Upstream Interface 1/0/0 1/0/1 1/1/0 1/1/1 1/2/0 1/2/1 1/3/0

Total Modems 2 0 0 0 0 0 2

Active Modems 2 0 0 0 0 0 1

Registered Modems 2 0 0 0 0 0 1

States

CASA CMTS

1/3/1

0

0

0

CASA-CMTS# show cable modem summary total CASA#show ca mo summary total Upstream Total Active Registered Interface Modems Modems Modems 1/0.0/0 0 0 0 1/0.1/0 1 1 1 1/1.0/0 0 0 0 1/1.1/0 0 0 0 1/2.0/0 0 0 0 1/2.1/0 0 0 0 1/3.0/0 0 0 0 1/3.1/0 0 0 0 1/4.0/0 0 0 0 1/4.1/0 0 0 0 1/5.0/0 0 0 0 1/5.1/0 0 0 0 1/6.0/0 0 0 0 1/6.1/0 0 0 0 1/7.0/0 0 0 0 1/7.1/0 0 0 0 Total: 1 1 1

Secondary Modems 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Offline Channel Modems Description 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Where:

CASA-CMTS# show cable modem summary tot Upstream Total Description Interface Modems 1/0.0/0 0 WC-02322 1/0.1/0 0 WC-02323

Active Modems 0 0

Registered

Secondary

Modems 0

0

0

0

Modems

Offline 0 0

Modems

CASA CMTS

1/1.0/0 WC-02324 Total:

0

0

0

0

0

0

0

0

0

0

:

X/Y/Z Where: x y z

CASA-CMTS>show cable modem downstream summary Downstream Total Active Registered Interface Modems Modems Modems 2/0/0 6 6 6 2/0/1 6 6 6 2/0/2 7 6 6 2/0/3 7 7 7 2/1/0 0 0 0 2/1/1 0 0 0 2/1/2 0 0 0 2/1/3 0 0 0 2/2/0 0 0 0 2/2/1 0 0 0 2/2/2 0 0 0 2/2/3 0 0 0 2/3/0 0 0 0 2/3/1 0 0 0 2/3/2 0 0 0 2/3/3 0 0 0

CASA-CMTS#show cable modem downstream 2/0/0 MAC Address IP Address US DS Intf Intf 0015.f2fe.9160 10.170.1.9 1/7.0/0 2/0/0 0015.f2fe.98a4 10.170.1.22 1/0.0/0 2/0/0 0015.f2fe.9ad5 10.170.1.27 1/0.0/0 2/0/0 0015.f2fe.9ad8 10.170.1.31 1/0.0/0 2/0/0 0015.f2fe.ba88 10.170.1.23 1/7.1/0 2/0/0 0015.f2fe.ce86 10.170.1.10 1/0.1/0 2/0/0

MAC Status online online online online online online

Prim Sid 282 269 288 279 274 257

RxPwr (dB) 0.7 -0.5 1.0 0.5 0.0 0.5

Timing Offset 2404 2404 2405 2404 2405 2405

Num CPEs 0 0 0 0 0 0

BPI Enb no no no no no no

CASA CMTS

CASA-CMTS#show cable modem phy MAC Address

US IF

0018.4de7.3d2a 11/0.0/0 c446.199d.fee8 11/0.0/0

DS IF

Sid

1/0/0 1/0/0

1 5

USPwr(dB) TX RX -0.5 0.7

USSNR (dB) 30.8 27.4

Timing Offset -

MicroReflec (dBc) -

:

Where:

<

e>

x/y Where:

x/y/z

DSPwr (dB) -

DSSNR Mode (dB) tdma tdma

CASA CMTS

x y z

x/y x/y/z Where: x y z

CASA-CMTS>show cable modem remote-query MAC Address IP Address S/N US DS TX Time Micro(dB) Modem Ratio Power Power Offset Reflection State 0015.f2fe.c643 10.160.1.9 36.2 42.4 5.5 2435 7 online

Where:

CASA-CMTS(config)# cable modem remote-query 1000

CASA CMTS

Where:

CASA-CMTS(config)# cable modem remote-query loopback 10

Where: mac_addr x y z

CASA-C2200(config)#cable modem remote-query 30 CASA-C2200(config)#show cable modem 0015.* remote-query MAC Address IP Address S/N US DS Ratio Power Power 0015.f2fe.9247 10.160.1.241 39.6 41.1 3.4 0015.f2fe.baac 10.160.1.223 37.1 38.4 3.1 CASA-C2200(config)#show cable modem 0015.* remote-query MAC Address IP Address S/N US DS Ratio Power Power 0015.f2fe.baac 10.160.1.223 37.1 38.4 3.1

TX Time Micro(dB) Offset Reflection 2434 11 2436 9 upstream 1/1/0 TX Time Micro(dB) Offset Reflection 2436 9

Modem State online online Modem State online

CASA CMTS

Where: ip_addr mask

CASA-CMTS# show cable modem 10.160.1.9 mask 255.255.255.255 remote-query MAC Address IP Address S/N US DS TX Time Micro(dB) Modem Ratio Power Power Offset Reflection State 0015.f2fe.c643 10.160.1.9 36.2 42.4 5.5 2435 7 online

Where:

CASA-CMTS(config)# cable flap-list aging 15

CASA-CMTS(config)#cable event priority warning 0x00 0x00 CASA-CMTS(config)#cable event priority notice 0x00 0x00 CASA-CMTS(config)#show cable event notification-policy priority flash-log mem-log traps syslog ------------------------------------------------emergency yes no yes yes alert yes no yes yes

CASA CMTS

critical error warning notice informational debug

yes yes no no yes yes

no no no no no no

yes yes no no yes yes

yes yes no no yes yes

CASA-CMTS(config)#cable event priority warning CASA-CMTS(config)#cable event priority notice

CASA-CMTS(config)# cable tcc us-bonding disable CASA-CMTS(config)# no cable tcc us-bonding disable

Where:

CASA CMTS

CASA-CMTS(config)#cable flap-list trap enabled

CASA-CMTS(config)#cable flap-list trap CASA-CMTS(config)#no cable flap-list trap

Where:

CASA-CMTS(config)#cable modem deny 0015.f2fe.cef2

CASA-CMTS(config)#cable admission-control preempt priority-voice

CASA CMTS

CASA-CMTS(config)#cable qos bw-reserve 80 upstream

CASA CMTS

CASA-CMTS(config)#cable qos temp-us-sf classname

Where:

CASA-CMTS(config)#cable dsx authorization CASA-CMTS(config)#no cable dsx authorization

CASA CMTS

Where:

CASA-CMTS(config)#cable mdd rcp fragment support CASA-CMTS(config)#no cable mdd fragment support

Where:

CASA-CMTS#cable mdd extended tx-power support 0 CASA-CMTS#cable mdd extended tx-power 1

CASA CMTS

Where:

CASA-CMTS(config)#cable upstream hi-power 3

Where:

CASA-CMTS(config)#cable upstream snr-interval 60

CASA CMTS

>

>

Where:

CASA-CMTS(config)#clear cable modem 015.f2fe.cef2

CASA-CMTS# show cable modem counters MAC Address US Packets US Bytes Bytes 0004.bd02.5050 9 1582 0011.e360.5655 0 0

DS Packets

DS

3 0

406 0

CASA CMTS

0011.e62b.6c0f 0 0 0 0013.115d.25a2 0 0 0 0014.6cb9.ff9f 9 1495 4 0015.e9a0.b8c6 44 4480 0 0016.ce88.8ab2 0 0 0 0017.9a5f.dcf9 0 0 0 CASA-CMTS# CASA-CMTS# clear cable modem 0014.6cb9.ff9f counters CASA-CMTS# show cable modem counters MAC Address US Packets US Bytes DS Packets Bytes 0004.bd02.5050 9 1582 3 0011.e360.5655 0 0 0 0011.e62b.6c0f 0 0 0 0013.115d.25a2 0 0 0 0014.6cb9.ff9f 0 0 0 0015.e9a0.b8c6 44 4480 0 0016.ce88.8ab2 0 0 0 0017.9a5f.dcf9 0 0 0 CASA-CMTS#

CASA-CMTS# clear cable modem offline

>

0 0 927 0 0 0

DS 406 0 0 0 0 0 0 0

CASA CMTS

CASA-CMTS# cable modem offline aging 10

CASA(config)# show cable modem offline MAC Address

US Intf

DS Intf

Prim Previous Offline Sid State Time

0008.0e41.5664 0015.f2fe.9a7e 0015.f2fe.b9fb 0015.f2fe.ba58 0015.f2fe.c643 0015.f2fe.ceb9 0022.102b.c609 0022.3ace.d9b9 0026.5e77.4463 0026.5e77.446c

0/3.1/0 0/0.0/0 0/3.0/0 0/3.1/0 0/2.0/0 0/3.0/0 0/0.1/0 0/0.0/0 0/0.1/0 0/0.1/0

1/3/3 1/2/2 1/3/2 1/2/3 1/3/0 1/3/1 1/2/1 1/3/0 1/3/0 1/2/1

61 57 67 62 52 51 50 54 60 58

online online online online online online online online online online

Rx RX Power SNR

2010-11-13,03:02:30 2010-11-13,03:02:30 2010-11-13,03:02:29 2010-11-13,03:02:35 2010-11-13,03:02:32 2010-11-13,03:02:34 2010-11-13,03:02:27 2010-11-13,03:02:35 2010-11-13,03:02:34 2010-11-13,03:02:30

-0.5 -0.5 0.0 0.0 0.2 0.0 0.0 -0.2 0.0 0.0

40.4 40.4 42.1 45.1 35.6 42.1 45.1 39.1 40.4 39.1

SM Exh.Cnt 16 16 16 16 16 16 16 16 16 16

CASA-CMTS# show cable modem vendor summary Vendor OUI Cable Modem Total Registered Unregistered Offline ZDT 00:15:f2 1 1 0 0 Motorola 00:20:40 28 28 0 0

CASA-CMTS# show cable modem vendor Vendor MAC Address US DS Num BPI Intf Intf CPEs Enb Motorola 0011.802c.43fe 3/4/0 1/0/0 0 no Motorola 0013.7163.0f92 3/4/0 1/0/0 0 no

MAC

Prim RxPwr Timing

State

Sid

(db)

Offset

online

2

-2.0

889

online

9

-2.0

882

CASA CMTS

Motorola 0 no Motorola 0 no Motorola 0 no Motorola 0 no Motorola 0 no Motorola 0 no Motorola 0 no Motorola 0 no Motorola 0 no

0013.7163.3ea2 3/0/0

1/0/0

online

1

-3.2

840

0013.7163.6980 3/4/0

1/0/0

online

24

-1.7

895

0013.716c.e0de 3/4/0

1/0/0

online

61

-1.7

838

0013.716c.f33e 3/4/0

1/0/0

online

19

-1.5

876

0013.716d.72a6 3/0/0

1/0/0

online

7

-2.7

878

0013.7176.d8f4 3/4/0

1/0/0

online

5

-2.0

871

0013.7176.ef86 3/4/0

1/0/0

online

62

-1.2

850

0013.7176.f8e6 3/4/0

1/0/0

online

63

-1.5

885

0013.7178.0812 3/4/0

1/0/0

online

25

-1.2

877

Where: <

>

<

CASA-CMTS#show cable modem 0015.f2fe.c904 vendor Vendor MAC Address US DS MAC Intf Intf State ZDT 0015.f2fe.c904 1/6/0 0/2/0 online

< Where:

><

>

Prim RxPwr Timing Num BPI Sid (db) Offset CPEs Enb 10 1.7 2180 0 no

CASA CMTS

< <

> >

CASA-CMTS# cable modem vendor 00:00:00 ABC

Where: <

>

CASA-CMTS(config)# no cable modem vendor 0:00:00

Where:

CASA-CMTS#show cable modem vendor all system default cm vendor database: cable modem vendor 00:0f:9f "Motorola" cable modem vendor 00:11:1a "Motorola" cable modem vendor 00:11:80 "Motorola" cable modem vendor 00:12:25 "Motorola" cable modem vendor 00:13:71 "Motorola" cable modem vendor 00:14:e8 "Motorola" cable modem vendor 00:18:c0 "Motorola" cable modem vendor 00:1a:ad "Motorola"

CASA CMTS

cable modem cable modem cable modem cable modem cable modem cable modem cable modem cable modem user config cable modem cable modem

vendor 00:1b:dd vendor 00:0f:21 vendor 00:11:e6 vendor 00:14:f8 vendor 00:16:92 vendor 00:18:68 vendor 00:19:47 vendor 00:1c:ea cm vendor: vendor 00:26:5e vendor 00:20:40

"Motorola" "Sci Atl" "Sci Atl" "Sci Atl" "Sci Atl" "Sci Atl" "Sci Atl" "Sci Atl" "Ubee" "Moto"

CASA-CMTS# show cable modem vendor summary Vendor OUI Cable Modem Total Registered Unregistered Offline ZDT 00:15:f2 1 1 0 0 Motorola 00:20:40 28 28 0 0

vendor_id Where: vendor_id

CASA-CMTS(config)#show cable modem vendor default cable modem vendor 00:0f:9f "Motorola" cable modem vendor 00:11:1a "Motorola" cable modem vendor 00:11:80 "Motorola" CASA-CMTS(config)#cable modem vendor 00:0f:9f ABC CASA-CMTS(config)#show cable modem vendor all system default cm vendor database: cable modem vendor 00:0f:9f "Motorola" cable modem vendor 00:11:1a "Motorola" user config cm vendor: cable modem vendor 00:0f:9f "ABC" CASA-CMTS(config)#default cable modem vendor 00:0f:9f CASA-CMTS(config)#show cable modem vendor all system default cm vendor database: cable modem vendor 00:0f:9f "Motorola" cable modem vendor 00:11:1a "Motorola" cable modem vendor 00:11:80 "Motorola”

CASA CMTS

<

Where:

CASA-CMTS# show cable modem CM Mac Address: Classifier ID: ServiceFlow ID: Direction: Rule Priority: Activation State: IP classifiers: ToS: Protocol: Source Address: Source Mask: Destination Address: Destination Mask: Source Port Start: Source Port End: Destination Port Start: Destination Port End: LLC classifiers: Destination Mac Address: Destination Mac Mask: Source Mac Mask: Ether Type: User Priority Low: User Priority High: Vlan ID: Bit Map: CM Interface Mask: Classifier ID: ServiceFlow ID: Direction: Rule Priority: Activation State: IP classifiers:

0050.f112.b764 classifiers 0050.f112.b764 3 514 Upstream 20 Active 0x00 0x00 0x00 17 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 0 65535 0 65535 0000.0000.0000 0000.0000.0000 0000.0000.0000 0x00 0x0 0x0 0x0 0xb 0x00.00.00.00 2 639 Upstream 10 Active

CASA CMTS

ToS: Protocol: Source Address: Source Mask: Destination Address: Destination Mask: Source Port Start: Source Port End: Destination Port Start: Destination Port End: LLC classifiers: Destination Mac Address: Destination Mac Mask: Source Mac Mask: Ether Type: User Priority Low: User Priority High: Vlan ID: Bit Map: CM Interface Mask:

0x00 0x00 0x00 256 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 0 65535 0 65535

Classifier ID: ServiceFlow ID: Direction: Rule Priority: Activation State: IP classifiers: ToS: Protocol: Source Address: Source Mask: Destination Address: Destination Mask: Source Port Start: Source Port End: Destination Port Start: Destination Port End: LLC classifiers: Destination Mac Address: Destination Mac Mask: Source Mac Mask: Ether Type: User Priority Low: User Priority High: Vlan ID: Bit Map:

5 641 Down 20 Active

Classifier ID: ServiceFlow ID: Direction: Rule Priority: Activation State: IP classifiers: ToS: Protocol: Source Address:

4 767 Down 10 Active

0000.0000.0000 0000.0000.0000 0000.0000.0000 0x00 0x0 0x0 0x0 0xb 0x00.00.00.00

0x00 0x00 0x00 17 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 0 65535 0 65535 0000.0000.0000 0000.0000.0000 0000.0000.0000 0x00 0x0 0x0 0x0 0xb

0x00 0x00 256 0.0.0.0

0x00

CASA CMTS

Source Mask: Destination Address: Destination Mask: Source Port Start: Source Port End: Destination Port Start: Destination Port End: LLC classifiers: Destination Mac Address: Destination Mac Mask: Source Mac Mask: Ether Type: User Priority Low: User Priority High: Vlan ID: Bit Map:

255.255.255.255 0.0.0.0 255.255.255.255 0 65535 0 65535 0000.0000.0000 0000.0000.0000 0000.0000.0000 0x00 0x0 0x0 0x0 0xb

Where:

C2800#show cable modem errors MAC Address US Intf DS Intf 0008.0d55.da42 1/3/0 0/0/1 0015.f2fe.bea2 1/3/0 0/0/3 0050.f112.b764 1/3/0 0/0/1

>|<

CRC 0 0 0

HCS 0 0 0

CASA CMTS

Where:

CASA-C3000(config)#show cable modem upstream 4/1.1/0 mac MAC Address MAC Prim Ver QoS Frag Concat Priv DS US State Sid Prov Saids Sids 0004.bd04.c1d8 online 17 DOC1.1 DOC1.1 YES YES 0 1 0005.caa3.d65c online 22 DOC3.0 DOC1.1 YES YES 0 1 000e.5c69.0188 online 6 DOC1.1 DOC1.1 YES YES 0 1 0011.8054.3af2 online 9 DOC2.0 DOC1.1 YES YES 0 1 0012.c99f.700a online 10 DOC2.0 DOC1.1 YES YES 0 1 0026.5e77.43ba online 27 DOC3.0 DOC1.1 YES YES 0 1 0026.5e77.43ce online 24 DOC3.0 DOC1.1 YES YES 0 1 0026.5e77.446e online 21 DOC3.0 DOC1.1 YES YES 0 1 CASA-C3000(config)#

> | <

Where:

PHS

YES BPI YES BPI YES BPI YES BPI YES BPI YES BPI YES BPI YES BPI

CASA CMTS

CASA-CMTS#show cable modem rogue MAC Address Vendor US Intf Ds Intf 0011.8078.1950 3/0/0 0/0/0 ba052c3991df6a933fa2c857f9654104 0013.7192.5b04 3/2/0 0/0/0 ba052c3991df6a933fa2c857f9654104

Spoof Count Dynamic Secret 4 5

Where:

CASA-CMTS#show cable modem maintenance MAC Address US Intf Ds Intf Prim Time Sid 0015.f2fe.c763 1/0/0 0/1/0 2 30,16:16:00 0015.f2fe.cee6 1/0/0 0/1/1 1 30,16:15:58 0015.f2fe.cef2 1/2/0 0/1/1 3 30,16:16:02

SM

Fail

Active-

Count 42

Count 0

2009-06-

43

0

2009-06-

44

0

2009-06-

CASA CMTS

CASA-CMTS# show cable modem deny

CASA-CMTS# show cable modem mac downstream summary Mac Version QoS Provision Mode Interface Total DOC3.0 DOC2.0 DOC1.1 DOC1.0 Register DOC2.0 DOC1.1 DOC1.0 0/0/0 0 0 0 0 0 0 0 0 0 0/0/1 0 0 0 0 0 0 0 0 0 0/0/2 0 0 0 0 0 0 0 0 0 0/0/3 0 0 0 0 0 0 0 0 0 0/1/0 0 0 0 0 0 0 0 0 0 0/1/1 0 0 0 0 0 0 0 0 0 0/1/2 0 0 0 0 0 0 0 0 0 0/1/3 0 0 0 0 0 0 0 0 0 0/2/0 1 0 1 0 0 1 0 1 0 0/2/1 0 0 0 0 0 0 0 0 0 0/2/2 0 0 0 0 0 0 0 0 0 0/2/3 0 0 0 0 0 0 0 0 0 0/3/0 0 0 0 0 0 0 0 0 0 0/3/1 0 0 0 0 0 0 0 0 0 0/3/2 0 0 0 0 0 0 0 0 0 0/3/3 0 0 0 0 0 0 0 0 0 Total:

1

0

1

0

0

1

0

1

0

CASA CMTS

Where:

CASA-CMTS(config)# interface docsis-mac 1 CASA-CMTS(conf-if-mac 1)# Where:

Where:

CASA-CMTS(config)# show interface docsis-mac 1 cable cm-status report event-list 5 cable cm-status event 1 max-timer 1500 maxnumber 35

CASA CMTS

Where:

CASA-CMTS(config)#show cable modem qos

CASA-CMTS> show cable modem qos Sfid

Dir Curr

Sid

State

Sched

Prio MaxSusRate MaxBrst MinRsvRate Throughput

Type

(kbps)

(kbps)

(kbps)

Mac Addr : 0012.c99f.700a Mac Addr : 0050.f112.b329 383

US

act

1

BE

0

0

3044

0

0

511

DS

act

N/A

UNDEF

0

0

3044

0

0

CASA-C3000> show cable modem qos | count-only "us act" Sfid

Dir Curr State

Count Line: 9854

Sid

Sched Type

Prio MaxSusRate MaxBrst MinRsvRate Throughput (kbps)

(kbps)

(kbps)

CASA CMTS

Where:

CASA-CMTS(config)#show cable modem docsis-mac 1

CASA-CMTS> show cable modem docsis-mac 1 MAC Address

IP Address

US

DS

MAC

Prim RxPwr Timing Num

BPI

Intf

Intf

Status

Sid

(dB)

Offset CPEs Enb

0012.c99f.700a 0.0.0.0

5/1.1/0

0/0/1

offline

0

0.0

0

0050.f112.b329 10.230.1.145

5/1.0/0*

0/0/0*

online(pt)

1

0.0

2442

0

yes

c0cb.38d3.6e74 0.0.0.0

5/1.0/0

0/0/0

init(r2)

206

6.2

2391

0

no

0

CASA-C3000>

CASA-CMTS> show cable modem docsis-mac 1 | count-only online MAC Address Timing Num

IP Address

US

DS

MAC

Prim RxPwr

Intf

Intf

Status

Sid

BPI

Offset CPEs Enb Count Line: 515

Where:

CASA-CMTS(config)# cable host authorization

(dB)

no

CASA CMTS

0015.f2fe.8d6a 10.160.1.40 CASA-CMTS(config)# CASA-CMTS(config)# no cable host authorization 0015.f2fe.8d6a 10.160.1.40 CASA-CMTS(config)#

CASA-CMTS(config)#show cable host authorization cable host authorization 0015.f2fe.8d6a 10.160.1.40

Subscriber management

CASA CMTS

cm_id cm_id Where:

CASA-CMTS(config)#docsis submgt cm-control cm 1 active true

Example: Enabling subscriber management CASA-CMTS# show cable modem MAC Address

IP Address

US Intf 0005.caa3.c38c 10.160.1.250 1/1/0* 0015.f2fe.9247 10.160.1.241 1/2/0 0015.f2fe.baac 10.160.1.223 1/2/0 0020.4058.c984 10.160.1.251 1/3/0 0026.5e77.43aa 10.160.1.252 1/1/0* online cm 5 ; offline cm 0 ; ranging cm 0

DS Intf 2/0/1* 2/0/0 2/0/2 2/0/3 2/0/2*

MAC Status online online online online online

Prim Sid 40 36 37 39 38

RxPwr (dB) 0.5 0.2 0.2 0.0 0.0

Timing Offset 2443 2432 2437 1674 2392

Num CPEs 0 0 0 0 0

CASA-C2200#show qos ds cm qam 2 ip address 10.160.1.252 | i cm_id nx=0 ty= 1 lc= 2 mc=0000 pcnt= 6 ir=1 0 0 10.160.1.252 00265e7743aa cm_id=5 cid=2 cm_tbl_idx= 16 cm_id=5 cid= 2 psid=38 v=3 00265e7743aa tek=02af3628 CASA-C2200#show qos ds cm qam 2 ip address 10.160.1.251 | i cm_id nx=0 ty= 1 lc= 2 mc=0000 pcnt= 10 ir=1 0 0 10.160.1.251 00204058c984 cm_id=4 cid=3 cm_tbl_idx= 17 cm_id=4 cid= 3 psid=39 v=0 00204058c984 tek=00000000 CASA-C2200#show qos ds cm qam 2 ip address 10.160.1.223 | i cm_id nx=0 ty= 1 lc= 2 mc=0000 pcnt= 4 ir=1 0 0 10.160.1.223 0015f2febaac cm_id=3 cid=2 cm_tbl_idx= 15 cm_id=3 cid= 2 psid=37 v=0 0015f2febaac tek=02af36a8 CASA-C2200#show qos ds cm qam 2 ip address 10.160.1.241 | i cm_id nx=0 ty= 1 lc= 2 mc=0000 pcnt= 4 ir=1 0 0 10.160.1.241 0015f2fe9247 cm_id=6 cid=0 cm_tbl_idx= 14 cm_id=6 cid= 0 psid=36 v=0 0015f2fe9247 tek=02af36e8 CASA-C2200#show qos ds cm qam 2 ip address 10.160.1.250 | i cm_id nx=0 ty= 1 lc= 2 mc=0000 pcnt= 4 ir=1 0 0 10.160.1.250 0005caa3c38c cm_id=1 cid=1 cm_tbl_idx= 18 cm_id=1 cid= 1 psid=40 v=3 0005caa3c38c tek=02af3668 CASA-CMTS(config)#docsis submgt cm-control cm 1 active true CASA-C2200#show qos ds cm qam 2 ip address 10.160.1.250 | i cm_id nx=0 ty= 1 lc= 2 mc=0000 pcnt= 4 ir=1 0 0 10.160.1.250 0005caa3c38c cm_id=1 cid=1 cm_tbl_idx= 18 cm_id=1 cid= 1 psid=40 v=3 0005caa3c38c tek=02af3668 CASA-C2200(config)#show docsis submgt cm 1 module 2 Submgt Active = 1 Submgt Learnable = 1 Submgt Max IP = 10

BPI Enb yes yes yes yes yes

CASA CMTS

Downstream Upstream Downstream Upstream Downstream Upstream Downstream Upstream Downstream Upstream

Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter

Entry Entry Entry Entry Entry Entry Entry Entry Entry Entry

0 0 1 1 2 2 3 3 4 4

= = = = = = = = = =

0 0 0 0 0 0 0 0 0 0

Where:

CASA-CMTS(config)#docsis submgt cm-control cm 1 learnable true

Where: num

CASA-CMTS(config)#docsis submgt cm-control cm 1 max-cpe-ip 10

CASA CMTS

Where: num

CASA-CMTS(config)#docsis submgt cm-control cm 1 max-cpe-ipv6-prefix 10

Where:

CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis

submgt submgt submgt submgt submgt submgt submgt submgt submgt submgt

default default default default default default default default default default

active [on|off] learnable [on|off] max-ip max-ipv6-prefix cm-filter-downstream cm-filter-upstream cpe-filter-downstream cpe-filter-upstream mta-filter-downstream mta-filter-upstream

CASA CMTS

CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis CASA-CMTS(config)#docsis

submgt submgt submgt submgt

default default default default

Where is one of the following:

stb-filter-downstream stb-filter-upstream ps-filter-downstream ps-filter-upstream

CASA CMTS

CASA-CMTS (config) #show docsis submgt default docsis submgt default active on docsis submgt default max-ip 16 docsis submgt default max-ipv6-prefix 16 docsis submgt default learnable on docsis submgt default cm-filter-downstream 0 docsis submgt default cm-filter-upstream 0 docsis submgt default cpe-filter-downstream 0 docsis submgt default cpe-filter-upstream 0 docsis submgt default ps-filter-downstream 0 docsis submgt default ps-filter-upstream 0 docsis submgt default mta-filter-downstream 0 docsis submgt default mta-filter-upstream 0 docsis submgt default stb-filter-downstream 0 docsis submgt default stb-filter-upstream 0

CASA CMTS

<

> <

>

Where:

Where:

CASA-CMTS#show docsis submgt ip-filter Group Index Accept Src Ip Mask Dst Ip Mask TOShi TOSMask Hit Cnt 1 1 1 0.0.0.0 0.0.0.0 10.200.3.5 10 0 255 0 0

UIP

TOSlo

255.255.255.255

CASA CMTS

Where:

CASA-CMTS# show docsis submgt cm 1 module 2 Submgt Active = 0 Submgt Learnable = 1 Submgt Max IP = 16 Downstream Filter Entry 0 = 0 Upstream Filter Entry 0 = 0 Downstream Filter Entry 1 = 0 Upstream Filter Entry 1 = 0 Downstream Filter Entry 2 = 0 Upstream Filter Entry 2 = 0 Downstream Filter Entry 3 = 0 Upstream Filter Entry 3 = 0 Downstream Filter Entry 4 = 0 Upstream Filter Entry 4 = 0

Where:

CASA-CMTS# show docsis submgt cm-control cm 1 cm=1 maxCpe IPv4=16 IPv6=16 active=false learnable=true reset=0 numOfCpeIp=0

CASA CMTS

Where:

CASA-CMTS#show docsis submgt cm-cpe-ip cm 3

Configuring MPEG Compliant Features

Where:

CASA-CMTS(config)# pat interval 500 CASA-CMTS# show running-config | i pat pat interval 500

CASA CMTS

Where:

CASA-CMTS(config)# pmt interval 500 CASA-CMTS# show running-config | i pmt pmt interval 500

Configuring DVB-compliant features

CASA CMTS

CASA-CMTS(config)# si generator eit CASA-CMTS(config)# no si generator eit

CASA-CMTS(config)# show running-config | i generator

CASA-CMTS(config)# si generator nit CASA-CMTS(config)# no si generator nit

CASA-CMTS(config)# show running-config | i generator

CASA-CMTS(config)# si generator sdt CASA-CMTS(config)# no si generator sdt

CASA-CMTS(config)# show running-config | i generator

CASA CMTS

CASA-CMTS(config)# si generator tdt CASA-CMTS(config)# no si generator tdt

CASA-CMTS(config)# show running-config | i generator

CASA-CMTS(config)# si generator tdt CASA-CMTS(config)# no si generator tdt

CASA-CMTS(config)# show running-config | i generator

Where:

CASA-CMTS(config)# interface qam 0/4 CASA-CMTS(config-if-qam)# Where: ch-id> net-id>

CASA CMTS

CASA-CMTS(config-if-qam)# channel 2 network id 16 CASA-CMTS(config-if-qam)# show interface qam 2/0 brief

interface qam 2/0 interleave 128x1 channel 0 frequency 549000000 no channel 0 shutdown channel 1 frequency 555000000 no channel 1 shutdown channel 2 frequency 561000000 channel 2 transport stream id 500 channel 2 network id 16 no channel 2 shutdown channel 3 frequency 567000000 no channel 3 shutdown no shutdown

Where:

CASA-CMTS(config)# interface qam 0/4 CASA-CMTS(config-if-qam)#

CASA CMTS

Where: ch-id> net-id>

CASA-CMTS(config-if-qam)# channel 2 transport stream id 500 CASA-CMTS(config-if-qam)# show interface qam 2/0 brief

interface qam 2/0 interleave 128x1 channel 0 frequency 549000000 no channel 0 shutdown channel 1 frequency 555000000 no channel 1 shutdown channel 2 frequency 561000000 channel 2 transport stream id 500 channel 2 network id 16 no channel 2 shutdown channel 3 frequency 567000000 no channel 3 shutdown no shutdown

Configuring the Time Offset Table

CASA CMTS

Where: string

0-60 CASA-CMTS# show timezone list

CASA-CMTS(config)# si generator tot country-code cet region-id 0

CASA-CMTS(config)#show running-config | i tot si si si si

generator generator generator generator

Where: -12 to 13 0, 30, 45

tot tot tot tot

country-code cet region-id 0 offset-hours 5 offset-minutes 30 dst begin month 4 week 1 time 2 dst end month 10 week 5 time 2

CASA CMTS

CASA-CMTS(config)# si generator tot offset-hours 5 offset-minutes 30

CASA-CMTS(config)# show running-config | i tot

Where: 1-12 1-5> 0-3>

CASA-CMTS(config)# si generator tot dst begin month 4 week 1 time 2

CASA-CMTS(config)# si generator tot dst end month 10 week 5 time 2

CASA-CMTS(config)# show running-config | i tot

Configuring the DOCSIS event notification policy

CASA CMTS

CASA-C10G(config)# cable event CASA-C10G(config)# no cable event

Where:

CASA-C10G(config)# no cable event 83020203 CASA-C10G(config)# show cable event runningconfig . .

CASA CMTS

cable event 83020103 cable event 83020200 cable event 83020201 cable event 83020202 no cable event 83020203

Where:

CASA-C10G(config)# show cable event runningconfig . . . cable event 83020103 cable event 83020200 cable event 83020201 cable event 83020202 no cable event 83020203

Where:

CASA CMTS

flags

CASA CMTS

CASA-CMTS#config)#show cable event notificationpolicy priority flash-log mem-log traps syslog ------------------------------------------------emergency yes no no no alert yes no no no critical yes no yes yes error yes no yes yes warning no yes yes yes notice no yes yes yes informational no no no no debug no no no no

ip_address> Where:

CMTS#config)#show running-config | i syslog !syslog server for DOCSIS events: cable event syslog-server 192.168.0.163

CASA CMTS

Where:

CMTS#config)#show running-config | i throttleadminStatus cable event throttle-adminStatus stopAtThreshold

Where: num

CASA CMTS

Where: num

CMTS#config)#show running-config | i throttlethreshold cable event throttle-threshold 1000

Using the logging commands

CASA CMTS

CASA CMTS

Where:

level

CASA-CMTS(config)# logging system notifications

CASA-CMTS(config)#logging host 192.168.8.123 CASA-CMTS(config)#logging host 192.168.8.145 CASA-CMTS(config)#logging syslog alerts

CASA CMTS

CASA-CMTS(config)#user log exclusion-list CASA-CMTS(user-log-exclusive-list)# Where:

CASA-CMTS(user-log-exclusive-list)# user test1 alert

CASA-CMTS(user-log-exclusive-list)# user test1 error

CASA CMTS

CASA-CMTS(config)#show logging all /dev/console : notifications system log level : notifications non-volatile log level : warnings volatile log level : errors syslog level : warnings syslog host: 192.168.8.123 192.168.8.145